SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 MONTOI, S.A. DE C.V. Libramiento Noreste Km.27 Escobedo, CP 66052 Nuevo Leon, Mexico Rodolfo Caballero Phone: 52-818154030 Email: Rodolfo.Caballero@Mattel.com Raymundo Rosas Phone: 52-818154030 Email: Raymundo.Rosas@Mattel.com MECHANICAL Valid To: December 31, 2018 Certificate Number: 2770.02 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on toys and other children s products 1 : Test/Tested Product Safety of Toys Basic Code Mechanical and Physical Properties GB 6675-1:2014 GB 6675-2:2014 (Sections 4.1-4.8, 4.10-4.15, 4.22, 4.23, 4.28, 5.1-5.14, 5.18, 5.22-5.25) Accessibility ASTM F963-11 (Sections 4.7, 8.5-8.10); ASTM F963-16 (Sections 4.7, 8.5-8.10); Mattel QSOP 0006-3010; 1 The Consumer Product Safety Improvement Act (CPSIA) requires that every children's product subject to a federal consumer product safety requirement be tested by a Consumer Product Safety Commission (CPSC) accepted laboratory for compliance with the applicable federal children's product safety requirements. Accreditation by A2LA does not infer acceptance by the CPSC. Please verify this organization s acceptance status by using the CPSC s searchable database, located at http://www.cpsc.gov/cgi-bin/labsearch/. (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 1 of 10
Sharp Points ASTM F963-11 (Sections 4.9-4.11, 8.5-8.10, 8.12); ASTM F963-16 (Sections 4.9-4.11, 8.5-8.10, 8.12); 16 CFR 1500.48; Mattel QSOP 0006-3020; Sharp Edges ASTM F963-11 (Sections 4.7, 4.10, 4.11, 8.5-8.10); ASTM F963-16 (Sections 4.7, 4.10, 4.11, 8.5-8.10); 16 CFR 1500.49; Mattel QSOP 0006-3030; Projections ASTM F963-11 (Sections 4.8, 8.5-8.10); ASTM F963-16 (Sections 4.8, 8.5-8.10); Mattel QSOP 0006-3035; Small Parts, Balls and Marbles ASTM F963-11 (Section 4.6); ASTM F963-16 (Section 4.6); 16 CFR 1501; Canadian Hazardous Products Act (HPA) (Schedule VIII, Pg. 26 A); Mattel QSOP 0006-3040; (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 2 of 10
Torque/Tension ASTM F963-11 (Sections 8.8 and 8.9); ASTM F963-16 (Sections 8.8 and 8.9); Mattel QSOP 0006-3060; Seam and Attachment Strength ASTM F963-11 (Sections 4.27 and 8.9.1); ASTM F963-16 (Sections 4.27 and 8.9.1); Mattel QSOP 0006-3070; Compression ASTM F963-11 (Section 8.10); ASTM F963-16 (Section 8.10); Mattel QSOP 0006-3110; Drop and Tip-Over Test ASTM F963-11 (Sections 8.7.1 and 8.7.2); ASTM F963-16 (Sections 8.7.1 and 8.7.2); 16 CFR 1500.50, 1500.51, 1500.52, and 1500.53; Mattel QSOP 0006-3120; Impact Test ASTM F963-11 (Section 8.7.4); ASTM F963-16 (Section 8.7.4); Mattel QSOP 0006-3130 (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 3 of 10
Tumble Test ASTM F963-11 (Section 8.7.3); ASTM F963-16 (Section 8.7.3); Mattel QSOP 0006-3140; Static and Dynamic Strength ASTM F963-11 (Sections 4.15, 8.5-8.10, 8.15, 8.20, 8.26); ASTM F963-16 (Sections 4.15, 8.5-8.10, 8.15, 8.21, 8.28); Mattel QSOP 0006-3151; ; Canadian Hazardous Products Act (HPA) Stability ASTM F963-11 (Sections 4.15, 8.5-8.10, 8.15, 8.20, 8.26); ASTM F963-16 (Sections 4.15, 8.5-8.10, 8.15, 8.21, 8.28); Mattel QSOP 0006-3152; Cords, Straps and Elastics ASTM F963-11 (Sections 4.14, 8.5-8.10, 8.22); ASTM F963-11 (Sections 4.14, 8.5-8.10, 8.23); Mattel QSOP 0006-3160; Finger Entrapment Openings in Rigid Materials ASTM F963-11 (Sections 4.18 and 8.5-8.10); ASTM F963-16 (Sections 4.18 and 8.5-8.10); Mattel QSOP 0006-3189; (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 4 of 10
Jaw Entrapment in Handles and Steering Wheels Movable Parts and Hinge Line Clearance ASTM F963-11 (Section 4.39); ASTM F963-16 (Section 4.39); Mattel QSOP 0006-3145 ASTM F963-11 (Sections 4.13, 4.18, 8.5-8.10, 8.25.1, 8.25.2); ASTM F963-16 (Sections 4.13, 4.18, 8.5-8.10, 8.26.1, 8.26.2); Mattel QSOP 0006-3200; Springs ASTM F963-11 (Section 4.18.6); ASTM F963-16 (Section 4.18.6); Mattel QSOP 0006-3201; Plastic Bags and Films ASTM F963-11 (Sections 4.12 and 8.21); ASTM F963-16 (Sections 4.12 and 8.22); Mattel QSOP 0006-3210; Sound Pressure Levels ASTM F963-11 (Sections 4.5, 8.5-8.10, 8.19); ASTM F963-16 (Sections 4.5, 8.5-8.10, 8.19); Mattel QSOP 0006-3400; ; ISO 8124-1 Teethers and Teething Toys ASTM F963-11 (Sections 4.22, 8.5-8.10); ASTM F963-16 (Sections 4.22, 8.5-8.10); Mattel QSOP 0006-3050 (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 5 of 10
Rattles ASTM F963-11 (Section 4.23); ASTM F963-16 (Section 4.23); 16 CFR 1510; Mattel QSOP 0006-3050 Toys with Nearly Spherical Ends ASTM F963-11 (Section 4.32); ASTM F963-16 (Section 4.32); Mattel QSOP 0006-3050 Hemispheric-Shaped Objects ASTM F963-11 (Section 4.36); ASTM F963-16 (Section 4.36); ISO 8124-1 QSOP 3050 Labeling Cords, Strings, and Elastics Labeling Battery Powered Ride on/in Toys ASTM F963-11 (Section 5 and 6); EN 71-6; Mattel QSOP 0006-3524; ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3536; ; NM300-1 Labeling Unassembled Products ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3556; (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 6 of 10
Safety Labeling Format ASTM F963-11 (Sections 5 and 6); 16 CFR 1500; Mattel QSOP 0006-3500; ; ISO 8124-1 Instructions for Use of Products of Consumer Interest Toys Furniture GB 5296-5:2006; GB 5296-6:2004 Tricycles Safety Requirements Handle Bar Strength Drop Test Sharp Point Sharp Edge Stability Load Test for Push Handles Front Wheel Retention Labeling Warning Statements for High Chairs High Chair Requirements Protective Components Tray Performance (Drop) Tray Performance (Pull) Static Load Stability Exposed Coil Springs Scissoring, Shearing and Pinching Restraint System Passive Crotch Restraint System Structural Integrity Tray Latch Release Mechanism Slide Containment ANSI Z315.1; 16 CFR 1500.49; 16 CFR 1500.50; 16 CFR 1500.51; 16 CFR 1500.52; 16 CFR 1500.53; 16 CFR 1501; Mattel QSOP 0006-3154; EN71-1 Mattel QSOP 0006-3586; ASTM F404; EN 14988-1; AS 4684; BS 5799; CEN/TR 13387 ASTM F404; EN 14988; AS 4684; GB 22793-1, -2:2008 (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 7 of 10
Labeling High Chair / Booster Seat Combination Products Labeling Warning Statements for Booster Seats Mattel QSOP 0006-3588; EN 16120; ASTM F2640; ASTM F404 Mattel QSOP 0006-3589; ASTM F2640; EN 16120 (Sections 9, 9.2, 9.4) Booster Seat Requirements ASTM F2640; EN 16120 Labeling Small Parts, Small Balls and Marbles ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3530; 16 CFR 1500; 16 CFR 1501; EN 71-1, -6; NM 300-1; Labeling Packaging Copy ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3510; 16 CFR 1500; EN 71-1, -6; NM 300-1; IS 9873-1 Labeling and Marking of Electrical Products Labeling and Marking of Battery Operated Products ASTM F963-11 (Sections 4.25, 8.5-8.12, 8.18.2, 8.18.4, 8.18.5, 8.18.6, 8.18.7, 8.18.8); ASTM F963-16 (Sections 4.25, 8.5-8.12, 8.18.3, 8.18.4, 8.18.5, 8.18.6, 8.18.7, 8.18.8); EN 62115; 16 CFR 1500; Mattel QSOP 0006-3534; NM300-6 ASTM F963-11 (Sections 4.25, 8.5-8.12, 8.18.2, 8.18.4, 8.18.5, 8.18.6, 8.18.7, 8.18.8); ASTM F963-16 (Sections 4.25, 8.5-8.12, 8.18.3, 8.18.4, 8.18.5, 8.18.6, 8.18.7, 8.18.8); Mattel QSOP 0006-3535; NM300-6 (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 8 of 10
Labeling Products with Circuit Boards Labeling Non-Battery Powered Ride on/in Toys and Toys With Weight Bearing Limits EN 62115; Canadian Radio Equipment Certification Procedure RSP-100 2 ; Mattel QSOP 0006-3544; NM300-6 ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3537; ; NM300-1 Labeling Tricycle ASTM F963-11 (Sections 5 and 6); Mattel QSOP: 0006-3504; ANSI Z315.1; EN 71-1 Labeling Battery Chargers ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3563; 16 CFR 1505.3; EN 71-6; ; NM 300-1 Labeling Sealed Lead Acid Batteries Labeling External Power Supplies and Transformers ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3592; 16 CFR 1500.121 ASTM F963-11 (Sections 5 and 6); Mattel QSOP 0006-3564; EN 62115; NM 300-6 Stationary Activity Centers ASTM F2012; EN 14036 2 This product certification procedure is not an accredited test and the inclusion of this procedure on this Scope does not confer laboratory accreditation to the procedure nor does it confer accreditation for the method(s) embedded within the procedure. The accredited test methods listed on this scope are used in determining compliance with this product certification procedure. (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 9 of 10
Labeling Stationary Activity Centers ASTM F2012; Mattel QSOP 0006-3577; EN 14036 Marking of Plastic Products GB 16288 Infant and Toddler Rockers ASTM F3084 Infant Swings ASTM F2088; EN 16232 (except finger entrapment for mesh products); Mattel QSOP 0006-3069; 16 CFR 1223 Labeling Infant Swings ASTM F2088 (Sections 8 and 9); Mattel QSOP 0006-3587; EN 16232 (Section 9) Child Use and Care Articles Chair Mounted Seats Labeling Child Use and Care Articles Chair Mounted Seats Child Use and Care Articles Baby Bouncers Labeling Child Use and Care Articles Baby Bouncers General Safety Technical Specification for Children s Furniture EN 16120 (except finger entrapment for mesh products) EN 16120 (Section 9) EN 14036 (except Section 7.6 (Static Strength)) EN 14036; Mattel QSOP 0006-3577 SN 2144:2008 Canada Toy Regulation SOR 2011/17 (A2LA Cert. No. 2770.02) Revised 03/01/2017 Page 10 of 10
Accredited Laboratory A2LA has accredited MONTOI, S.A. DE C.V. Escobedo, Nuevo Leon, Mexico for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 23 rd day of November 2016. President and CEO For the Accreditation Council Certificate Number 2770.02 Valid to December 31, 2018 For the types of tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.