RPMAC Inverter Duty Motors Stock Model Number Cross Reference List

RPMAC Inverter Duty Motors Stock Model Cross Reference List L180 to RL210 Functional Replacement The following RL210 frames are intended to be only functional replacements of the L180 RPMAC frames, which have been discontinued. We have upgraded this part of our product line so that we can offer a complete laminated steel frame from 2 HP through 1000 HP. The RL210 is not mechanically interchangeable with the L180 since it is a 210 frame. However, if the L180 was a flange mounted motor, then the RL210 will have the same NEMA C-face and shaft as the original L180 TC frame. The RL210 frame motors will typically provide the same continuous and overload torques as the L180 overload torque provided. However, the inertia of Rl210 frames is greater than L180 frames. For a lower inertia option that will more closely match the inertia of the L180 frames, please see data for frames designated ARL210 series. HP 2 3 5 7.5 10 Base Speed C. HP Speed Voltage Enclosure Old Frame Old Model New Frame New Model Mounting Dimension Sheet 1150 2300 460 TENV L1831 P18L275 RL2153 P21R335 Foot 617254-1 850 1700 460 TENV L1831 P18L276 RL2153 P21R336 Foot 617254-1 650 1300 460 TENV L1831 P18L277 RL2153 P21R337 Foot 617254-1 1150 2300 460 TENV L1831 P18L279 RL2153 P21R338 Foot 617254-1 850 1700 460 TENV L1838 P18L280 RL2153 P21R339 Foot 617254-1 650 1300 460 TENV L1844 P18L281 RL2153 P21R340 Foot 617254-1 3550 4000 460 TENV NEW NEW RL2153 P21R341 Foot 617254-1 2500 5000 460 TENV L1831 P18L283 RL2153 P21R386 Foot 617254-1 1750 3500 230/460 TENV L1831C P18L261 RL2153C P21R307 FT/ (180TC) 617254-33 1750 3500 230/460 TENV L1831C P18L332(#) RL2153C P21R373(#) FT/ (180TC) 617254-33 1150 2300 460 TENV L1838 P18L284 RL2158 P21R342 Foot 617257-1 850 1700 460 TENV L1852 P18L285 RL2162 P21R343 Foot 617200-1 850 1700 460 TEBC L1838 P18L286 RL2153 P21R344 Foot 617255-1 650 1300 460 TEBC L1838 P18L287 RL2153 P21R345 Foot 617255-1 3550 4000 460 TENV L1838 P18L288 RL2153 P21R346 Foot 617254-1 2500 5000 460 TENV L1838 P18L269 RL2153 P21R387 Foot 617254-1 1750 3500 230/460 TENV L1844C P18L262 RL2158C P21R308 FT/ (210TC) 617257-3 1750 3500 230/460 TENV L1844C P18L263(@) RL2158C P21R374(@) FT/ (210TC) 617257-3 1750 3500 230/460 TENV L1844C P18L333(#) RL2158C P21R375(#) FT/ (210TC) 617257-3 1150 2300 230/460 TENV L1852 P18L290 RL2162 P21R347 Foot 617200-3 1150 2300 460 TEBC L1838 P18L291 RL2153 P21R348 Foot 617255-1 850 1700 460 TEFC L1852 P18L339 RL2158 P21R382 Foot 617255-1 850 1700 460 TEBC L1844 P18L293 RL2153 P21R333 Foot 617255-1 650 1000 460 TEBC L1852 P18L295 RL2158 P21R349 Foot 617258-1 3550 4000 230/460 TENV L1844 P18L296 RL2158 P21R320 Foot 617257-1 2500 5000 460 TENV L1844 P18L297 RL2158 P21R350 Foot 617257-1 1750 3500 230/460 TENV L1852C P18L264 RL2162C P21R309 FT/ (210TC) 617200-3 1750 3500 230/460 TENV L1852C P18L265(@) RL2162C P21R376(@) FT/ (210TC) 617200-3 1750 3500 230/460 TENV L1852C P18L334(#) RL2162C P21R377(#) FT/ (210TC) 617200-3 1150 2300 460 TEFC L1852 P18L340 RL2162 P21R329 Foot 617201-1 1150 2300 460 TEBC L1844 P18L298 RL2153 P21R351 Foot 617255-1 850 1050 460 DPG-FV L1844 P18L299 RL2153 P21R371 Foot 617256-1 850 1700 460 TEBC L1852 P18L300 RL2158 P21R383 Foot 617258-1 650 850 460 DPG-FV L1852 P18L301 RL2158 P21R352 Foot 617259-1 (#) -Includes BEI HS35 encoder (@) - Includes Dynapar H20 encoder M-183

Large AC RPMAC Inverter Duty Motors Stock Model Cross Reference List L180 to RL210 Functional Replacement RPM III Medium DC Motors RPM XL Small DC Motors RPM AC Inverter Duty Inverter Duty AC Motors HP 15 20 25 30 40 Base Speed C. HP Speed Voltage Enclosure Old Frame Old Model New Frame New Model Mounting Dimension Sheet 3550 4000 460 DPG-FV L1838 P18L302 RL2153 P21R353 Foot 617256-1 3550 4000 460 TEBC L1838 P18L304 RL2153 P21R354 Foot 617255-1 3550 4000 230/460 TENV L1852 P18L303 RL2162 P21R330 Foot 617200-1 2500 3600 460 DPG-FV L1838 P18L305 RL2153 P21R355 Foot 617256-1 2500 5000 460 TEBC L1838 P18L306 RL2153 P21R356 Foot 617255-1 1750 3500 460 DPG-FV L1838 P18L307 RL2153 P21R357 Foot 617256-1 1750 3500 460 TEFC L1852C P18L266 RL2158C P21R358 FT/ (250TC) 617258-13 1750 3500 460 TEFC L1852C P18L267(@) RL2158C P21R378(@) FT/ (250TC) 617258-13 1750 3500 460 TEFC L1852C P18L335(#) RL2158C P21R379(#) FT/ (250TC) 617258-13 1750 3500 460 TEBC L1844 P18L325 RL2153 P21R359 Foot 617255-1 1150 1300 460 DPG-FV L1844 P18L308 RL2153 P21R372 Foot 617256-1 1150 2300 460 TEBC L1852 P18L309 RL2162 P21R360 Foot 617201-1 850 1050 460 DPG-FV L1852 P18L310 RL2158 P21R361 Foot 617259-1 3550 4000 460 DPG-FV L1838 P18L317 RL2153 P21R363 Foot 617256-1 3550 4000 460 TEBC L1838 P18L318 RL2153 P21R323 Foot 617255-1 2500 3600 460 DPG-FV L1838 P18L319 RL2153 P21R362 Foot 617256-1 2500 3600 460 TEFC L1852 P18L338 RL2158 P21R384 Foot 617258-1 2500 5000 460 TEBC L1844 P18L320 RL2158 P21R364 Foot 617258-1 1750 2890 460 DPG-FV L1838C P18L328 RL2153C P21R365 FT/ (250TC) 617256-13 1750 3500 460 TEBC L1852C P18L268 RL2158C P21R314 FT/ (250TC) 617258-13 1750 3500 460 TEBC L1852C P18L269(@) RL2158C P21R380(@) FT/ (250TC) 617258-13 1750 3500 460 TEBC L1852C P18L336(#) RL2158C P21R381(#) FT/ (250TC) 617258-13 1150 1300 460 DPG-FV L1852C P18L329 RL2158C P21R315 FT/ (250TC) 617258-13 3550 4000 460 DPG-FV L1838 P18L321 RL2153 P21R366 Foot 617256-1 3550 4000 460 TEBC L1844 P18L322 RL2158 P21R331 Foot 617258-1 2500 3600 460 DPG-FV L1838 P18L323 RL2153 P21R367 Foot 617256-1 2500 5000 460 TEBC L1852 P18L324 RL2162 P21R385 Foot 617201-1 1750 2600 460 DPG-FV L1844C P18L330 RL2158C P21R368 FT/(250TC) 617259-13 3550 4000 460 DPG-FV L1838 P18L311 RL2153 P21R317 Foot 617256-1 3550 4000 460 TEBC L1852 P18L312 RL2162 P21R328 Foot 617201-1 2500 3000 460 DPG-FV L1844 P18L313 RL2153 P21R369 Foot 617256-1 1750 3475 460 DPG-FV L1852C P18L331 RL2158C P21R327 FT/ (250TC) 617259-13 3550 4000 460 DPG-FV L1844 P18L314 RL2158 P21R324 Foot 617259-1 2500 3000 460 DPG-FV L1852 P18L315 RL2158 P21R370 Foot 617259-1 50 3550 4000 460 DPG-FV L1852 P18L316 RL2162 P21R325 Foot 616795-1 (#) -Includes BEI HS35 encoder (@) - Includes Dynapar H20 encoder General Information For pricing information or to place orders, go to www.ptplace.com M-184

RPM AC INTEGRAL HP INVERTER DUTY MOTORS GENERAL INFORMATION GENERAL FEATURES UNIQUE SQUARE LAMINATED STEEL FRAME RPM AC motors are designed specifically for optimum inverter duty performance. From three generations of successful experience with laminated frame DC motors, RPM AC motors have been designed as square, laminated steel frame (RL210 - L440 NEMA & RDL132-DL280 IEC) to achieve maximum performance on inverter power. RPM AC customer benefits: Most cost effective solutions in the industry Square frame designs allow larger horsepower ratings in smaller frame sizes than NEMA cast iron motors without compromise in performance or life Stock availability from 1/3-1000 HP Replace larger frame NEMA AC and DC motors easily 1000:1 constant torque in vector mode is standard on DPFV, TENV, TEBC and TEFC as shown in catalog. Feet located on cast iron brackets provide more rigid, vibrationresistant structure. Rugged laminated steel frames Wide constant horsepower range - 4:1 to 12:1 available High peak torque- 200% standard on enclosed motors; 300% to 400% available upon request Low inertia for fast acceleration Mount multiple accessories easily - encoders, brakes Encoder provisions: machined opposite drive end bracket and tapped shaft for addition of stub shaft are standard on DPFV, TENV and TEBC; a tapped shaft only is standard for TEFC for ease of mounting HS35 hollow shaft encoders. TEFC 1000:1 Constant Torque RL2173 Frame Typical Applications RPM AC motors have been successfully applied on a wide variety of applications. Because of the versatility to meet both wide constant torque and constant HP needs, optimum power matched solutions are available for the following: Constant Torque: Extruders, injection molding, conveyors, paper machines, crane and hoist. Includes web processing on printing press, metal coating, film and paper coating. Cut-to -length applications on shears used in metals and paper corrugators utilize the low inertia and mechanical ruggedness of laminated frame RPM AC Constant Horsepower: Winders, unwinders, recoilers, tension reels, and machine tool spindle are examples where high peak torque to inertia for fast acceleration, and constant HP ranges of 4:1 up to 16:1 have been supplied. The ability to design very low base speeds and high response are standard with RPM AC. High shock and Vibration: Stamping presses for automotive and metal stamping take advantage of compact designs with feet on the brackets directly under the bearings. Includes high horsepower top drives for off shore oil rigs with the added demands of high humidity, salt spray and extreme ambient conditions. Test stands: Again, the fast response and compact mechanical features of RPM AC make it the choice solution for test stand applications. Depending on frame size, maximum speeds of 4000-8500 RPM are available. Variable Torque Loads: Because of the economic advantages and compactness of RPM AC motors, many customers have selected DPFV RPM AC for many variable torque applications, particularly for high horsepower requirements. M-185

Inverter Duty AC Motors RPM AC Inverter Duty RPM XL Small DC Motors Large AC APPLICATION TOOLS The RPMAC MOTOR WIZARD is a patented, revolutionary inverter duty motor selection program. For custom motor requirements not found in the catalog, the WIZARD allows you to input exact values of altitude, ambient, base speed, wide constant HP speed ranges, enclosure, voltage, continuous torque and overload torque. The output includes: motor frame size, inverter kva, and typical motor amps. It allows evaluation of lower cost alternatives based on your needs. You can immediately print typical performance data curves, motor, conduit box and encoder typical dimensions. A DUTY CYCLE CALCULATOR is included in the RPM AC Motor Wizard to determine the motor frame size for load torques which vary cyclically over time. The RPMAC MOTOR WIZARD CD can be ordered from Rockwell Automation, ordering number RAPS-517, through your Rockwell Automation contact. It can also be downloaded from the web at www. reliance.com. We encourage customer use of this powerful tool to aid in rapid selection of the exact motor for your application needs BASIS OF RATINGS The RPM AC motors in this catalog are designed specifically for use on IGBT voltage source controllers (PWM and six step VVI). Motor characteristics are optimized to reduce peak currents from the controller as well as to minimize motor losses. When the AC controller is properly adjusted, RPM AC motor performance will be in accordance with published rating data. The ratings in this catalog are based on a minimum PWM frequency of 4 khz for HP through 500, 2 khz for 600 HP and higher, and a minimum ratio of PWM frequency: fundamental frequency of 20:1. Totally Enclosed Blower Cooled With Mounted Encoder VOLTAGE SPIKE CAPABILITY CORONA-FREE DESIGNS dv/dt and peak voltages) RPM AC insulation systems have been tested extensively to insure successful operation on inverter waveshapes, including fast switching IGBTs. All motors are designed to withstand high peak voltages caused by the combination of long lead lengths and steep voltage wavefronts, with no corona formation, for AC input voltages up to 575 volts RMS. Consult the control manufacturer for specific lead length recommendations. All RPM AC motors have been designed to surpass the requirements of NEMA MG-1 1998, Part 31, Section 4 for definite purpose, inverter fed, polyphase motors for voltage spikes. All RPM AC motors for base voltage rating of 460 volts and below have been qualified by test to meet a minimum of 1600 volts peak, and a dv/dt in excess of 10,000 volts per microsecond. For voltages above 460 volts, including 575 volts, motors use an insulation system which is qualified by test to meet minimum peak voltages of 1850 volts and dv/dt in excess of 10,000 volts per microsecond rate of rise. RPM III Medium DC Motors General Information For pricing information or to place orders, go to www.ptplace.com M-186

STANDARD MOTOR FEATURES AGENCY LISTINGS AND CERTIFICATIONS RL210 through L440 Frame ORDINARY LOCATIONS All RPM AC motors are eligible for UL component listing and CSA Certification for Ordinary s for all enclosures. (Please note blower changes on certain TEBC Stock Ratings below for UL listing.) On stock motors, the CSA mark for ordinary locations on all RPM AC motors in frames RL210 - L440 (all enclosures), and UL logo in TEBC frames L360 - L440 is standard. Both the CSA CSA file number LR40567 mark and UL logo are standard on stock DPFV and TEFC models in frames RL210 - L440, and all TENV stock models. The CSA mark and UL logo can be supplied on all production motors. The UL logo can be obtained on stock TEBC RL210 - L320 by requesting the 56 frame blower package at no extra charge. Motor dimensions will change with 56 frame blower. All RPM AC IEC frame motors include the CE mark as standard. The CE mark can be supplied on any motor, NEMA or IEC frame, but must be requested at time of order entry for NEMA frames, both stock and production. IMPORTANT Motors with modifications or accessories not approved by UL or CSA may not have the agency logo stamped on the nameplate CLASSIFIED AREAS - HAZARDOUS LOCATIONS Class 1 Division 2 Certification Inverter Duty RPM AC * RPM AC motors have been tested and certified by CSA for operation on inverter power in areas classified as Class 1, Groups A, B, C and D, Division 2 for all TENV, TEBC, TEFC and DPFV CSA file number LR46877 enclosures. See Pricing and Modifications sections of catalog. Motor frame size will vary based on the NEC temperature code specified. Contact Rockwell Automation Sales Engineers representing DODGE and Reliance Electric brands of products for details. NOTE: Accessories supplied and mounted on the motor must be approved for Class 1, Division 1 or 2 and the same groups as main motor. This will limit the availability of some modifications. See available modifications in this catalog for further details. * Groups A and B not available on TEBC Enclosure Class 1 Division 1 RPM AC motors have been tested and approved by CSA for Class 1 Division 1 or 2 locations for Totally Enclosed Pipe In/ Pipe Out Ventilation - see Application section for details. For UL listed Division 1 explosion proof motors for inverter duty, see Variable Speed catalog. ALTITUDE - AMBIENT All motors in this catalog are based on 40 degrees C ambient, altitude of 3300 feet (1000 meters) above sea level at 1.0 service factor on inverter power. All motors are suitable for low ambient down to -25C as standard. Modifications can be selected for service factor, ambient and altitude as needed from the modification section. ADJUSTABLE SPEED CAPABILITY All RPM AC motors in this catalog are rated Vector Duty, in that they are capable of 1000:1 constant torque below base speed. They are suitable for full load torque continuously at zero speed. RPM AC motors may be applied to inverters that are configured for vector control with encoder (flux regulated vector), sensor less vector, or scalar (volts per hertz operation). The constant torque speed range obtained is dependent on the control s ability to properly regulate the motor flux. For example, continuous torque at zero speed may require a vector control with encoder feedback, depending on the specific performance requirements, including overloads and transient response Enclosure Below Base Speed Constant Torque (1) Speed Range Above Base Speed Constant Horsepower TEBC 1000:1 2:1 (2) TENV 1000:1 2:1 (2) TEFC 1000:1 2:1 (2) DPFV 1000:1 AS PUBLISHED (1) suitable for Full Torque down to zero speed continuously on Vector controllers on which motor flux is regulated (2) See price section and Application Data for speed limitations TEFC 1000:1 Constant Torque 25 HP 1750 RPM M-187

RPM III Medium DC Motors RPM XL Small DC Motors RPM AC Inverter Duty Inverter Duty AC Motors Large AC OPTIMIZED FOUR & SIX POLE DESIGNS The ratings in this catalog are based on the use of four pole laminations in frames RL210 thru L400, and six pole in L440 frame, for adjustable frequency service. By designing the motor for rated voltage at the desired base speed, motor current and therefore controller size can be minimized. The base speed is obtained by adjusting the controller frequency as required. For example, with four poles, a base speed of 1750 RPM at 460 volts would require a 60 Hz nominal controller output frequency at 460 volts. A base speed of 850 RPM would require a 30 Hz frequency setting at 460 volts output. Using this approach, motors of the same horsepower with different base speeds will have the same nominal full load current even though frame sizes will change. Motor designs are optimized for the exact base speed and not derated or overframed. NOTE: RPM AC motors are optimized for inverter power supplies. Contact Reliance Electric if by-pass mode (across-the-line) is required. BALANCE Standard - All RPM AC motors meet the dynamic balance limits of NEMA MG1 Part 7 for peak value of the unfiltered velocity in inches per second as shown below: Standard Balance Limits RPM RL210 - L440 Velocity (inches / sec) Peak 0-1200 Per NEMA Standard 1201-1800.15 1801-3600.15 3601-5000.2 5001-8000.2 See Modification section for higher grade balance (Ultra Standard and Precision) and NEMA Standard in Table 1 in Modification Section. BEARING - INSULATED All RPM AC L440 frames include insulated opposite drive end bearing as standard. BEARINGS - LUBRICATION Standard - All RPM AC motors use deep-grooved anti-friction ball bearings. Oversized ball bearings are standard on frames RL210 through RL250 for both coupled and belted duty. Roller bearings are used for belted duty on frames UL280 through UL440. These bearings and their internal clearances have been especially selected based on load carrying ability, thermal stresses and speed range consistent with ample bearing life. Double shielded bearings with oversize grease reservoirs that provide lifetime lubrication with no maintenance are standard on RL210-RL250 frames; bearings in frames RL210 & RL250 are not regreasable. Exclusive PLS lubrication incorporating open bearings with inner caps is standard on L280-L440 frames. See the Application Section for bearing life data. CONDUIT BOX (TERMINAL HOUSING) Standard construction for frames RL210 through L360 provides a gasketed, stamped steel box and cover. Boxes can be rotated in 90 degree increments, and located in any quadrant as long as accessories are not in the same quadrant. Standard construction for frames L400 and L440 are heavy gauge mill type conduit boxes which can be mounted on either side or the top of the motor as long as not in the same quadrant as the blower. See the Modification Section for location and construction options. Standard Conduit Box For All Frames, Including Stock Models Frame Enclosure Terminal Blocks RL210 - L400 L440 TENV / TEBC Top (F-3) Option DPG-FV F-1 Option TEAO-P/B F-1 Option DPG-FV F-1 Option For XT, Outdoor, or Paper Mill Duty, cast iron boxes are standard in frames RL210-L360. A large mill box is standard on L400 designs and all L440 frames. Other conduit box locations available on stock RL210-L440 and production. See modification section. CONNECTIONS Motor power leads and thermostat leads are terminated in the conduit box and have sufficient length (approximately 6 inches) for connecting to the power leads. DIRECTION OF ROTATION All RPMAC motors are designed for bi-directional rotation. All motors are phase sequenced so that when voltages in an A-B-C phase sequence are applied to leads U/T1, V/T2, W/T3 clockwise shaft rotation facing the opposite drive end will occur. ENCLOSURES The basic price pages contain pricing for totally enclosed and drip-proof guarded force-ventilated motors. The IEC enclosure terminology is shown for reference only. Drip proof Guarded Force Ventilated (IEC IP23/IC06) - ratings through 1000 HP (725kw) at 1750 RPM continuous duty (S1) are available. Totally Enclosed Non-Ventilated (IEC IP44/IC410) - ratings available through 100 HP (75kw) continuous duty (S1), and 400 HP (300kw) 60 minute duty (S2-60 minutes) Totally Enclosed Fan Cooled (IEC IC411) - ratings available through 250 HP (186kw) at 1750 RPM Totally Enclosed Blower Cooled (IEC 416)- ratings available through 500 HP at 1750 RPM; IEC IC416 available up to 300kw at 1450 RPM. Motors designed for higher than standard speeds may use special bearing construction other than stated above. General Information For pricing information or to place orders, go to www.ptplace.com M-188

ENCLOSURES con t The selection of the proper enclosure is vital to the successful safe operation of AC motors. The wrong enclosure can pose hazards to operating personnel and endanger other equipment. In addition, machine performance and life can be materially reduced by using an enclosure inappropriate for the application. The customer must recognize the specific environmental conditions and specify the correct enclosure. Reliance Electric can provide application assistance but must depend on the customer to provide accurate information on the operating conditions. The information in this section and the Modification Section should be studied thoroughly before specifying an enclosure. As indicated in the Introduction Section, the basic RPM AC motor may be Drip-proof Guarded Force Ventilated, Drip-proof Guarded Separately Ventilated or totally enclosed. The minimum enclosure for RPM AC motors is Drip-proof Guarded (Force Ventilated) as defined by NEMA MG1-1.25.5 to prevent accidental exposure to live metal or rotating parts. The drip-proof construction permits successful operation when drops of liquid or solid particles strike or enter the enclosure at any angle from 0 to 15 degrees downward from the vertical. Certain applications may require the Splashproof Guarded (Force Ventilated) machine to permit successful operation when drops of liquid or solid particles strike or enter the enclosure at any angle not greater than 100 degrees downward from the vertical. Both Drip-proof Guarded Force Ventilated and Splashproof Guarded Force Ventilated machines have a blower driven by a constant speed AC motor mounted on the end bracket to provide cooling independent of AC motor speed. A filter may be added to the blower when filterable contaminants are present in amounts not sufficient to rapidly clog the filter. A filter is not recommended in extremely dusty, dirty locations. Drip-Proof Guarded Force Ventilated (DPFV) Motor cooling is provided by motor-mounted blower driven by an integrally mounted three-phase blower motor. CAUTION: The blower cooling system is designed for optimum cooling air flow. Blowers must not have any auxiliary duct work connected to the inlet shroud since reduction in air flow and motor overheating will occur. Drip-Proof Guarded Separately Ventilated (DPSV) For applications where cooling air is ducted to the motor from an external source provided by the customer. For dusty, dirty environments, a totally enclosed machine is required to prevent the free exchange of air between the inside and outside of the enclosure but not sufficiently enclosed to be termed air-tight. Totally Enclosed Air Over-Blower Cooled (TEBC) RPM AC in-line blower cooled motors incorporate unique integral air ducts in the stator frame, external to the windings, to provide maximum cooling effectiveness. The integrally mounted, independently powered threephase blowers result in low noise levels over wide speed ranges. TEAO- Piggyback blower is available as an option. Totally Enclosed Non-Ventilated (TENV) Does not require any external air flow for cooling. Totally Enclosed Fan Cooled (TEFC) Exterior surface cooled by external fan mounted on motor shaft, therefore making motor cooling dependent on motor speed. XT Features Provides protection against corrosive, moist and dirt laden environments as encountered in paper, chemical and similar industries. Applicable to totally enclosed motors built in frames RL210 - L440 only. Outdoor Duty/Washdown Duty Suitable for operation outdoors subject to direct weather conditions, or for frequent washdown by high pressure water or steam. Available in all frame sizes RL210 - L440 on production basis. Paper Mill Duty Features Designed for operation at the wet end of a paper mill and in other harsh industrial environments. Totally Enclosed Pipe-Ventilated (TEPV) or Totally Enclosed Separately-Ventilated (TESV) Motor is cooled by customer supplied air which is piped into the machine and ducted out of the machine by customer supplied ducts. FINISH-PAINT Standard finish is Reliance Electric blue-green (Munsell Color System 8.5BG3.57/2.0) high-grade modified epoxy, air dry enamel with nontoxic rust inhibitors. GROUNDING Motors powered from adjustable frequency controllers will have voltages induced on inactive components, such as the motor frame, as a result of capacitive coupling of the switched voltage wavefronts from the controllers. PROPER GROUNDING OF THE MOTOR FRAME IS ESSENTIAL. All RPM AC motors have a ground lead provided in the motor conduit box as standard for grounding. INSULATION SYSTEM The standard insulation system for RPM AC is thermally rated for NEMA Class H of 180 C. All components of the system have been carefully selected to be fully compatible with any IGBT voltage source type controller, whether it is PWM or VVI. Premium VPI insulation is standard on all RPM AC L440 frames. MOUNTING All RPM AC frames are suitable for floor, wall or ceiling mount and with shaft at any angle from horizontal to vertical. M-189

Large AC OVERLOADS Momentary Overloads - all RPM AC motors have been designed for an overload capability of 150% (for DPFV) and 200% (for TEBC, TENV, and TEFC) of the base speed full load torque for 1 minute at all speeds within the constant torque speed range Inverter Duty AC Motors TEFC With Hollow Shaft HS35 Encoder Typical RPM Motor Construction With Totally Enclosed In-line Blower and Pulse Tachometer RPM AC Inverter Duty RPM XL Small DC Motors RPM III Medium DC Motors TACHOMETER MOUNTING All RPM AC motors have as a standard feature a machined opposite drive end bracket and tapped shaft provision for stub shaft for mounting an integral encoder. Mounting kits are available for selected encoders. The most cost effective encoder selection is a hollow shaft design and since it mounts on the stub shaft, no coupling or adapter is required. A tether arm mounts to the motor bracket. For TEFC motors in RL210 - L400 frames, a fan cover with machined fit for accessory mounting is available as a modification, if brakes and/or coupled/bearingless encoders are required. See Variable Speed catalog RAPS 692-1 for detail. TEST - STANDARD DPFV 1000HP 1750 RPM L4461 Frame Each motor is given a full load test on a PWM power supply, and a routine test in accordance with IEEE 112 as modified by Reliance Electric for inverter power. This provides customers with assurance that all motors meet design specifications. Routine test consists of: Stator winding resistance Hi potential test No load and full load amps No load and full load speed See Modification section for price to supply certified routine test report price and other test options. THERMAL PROTECTION All RPM AC motors include three normally closed thermostats (1 per phase) connected in series, as standard. Leads are brought into the main conduit box as standard. General Information For pricing information or to place orders, go to www.ptplace.com M-190

SMALL RPM AC MOTOR Totally enclosed, non-ventilated and blower cooled enclosures meet IP44. (1/3 to 5 HP) Washdown Duty, totally enclosed, non-ventilated enclosures meet IP55. (1/3 to 3 HP) Mounting configured for C-Face foot mounted as standard. Top mounted conduit box capable of F1 or F2 lead location. 1000:1 Constant Torque Speed Range. Constant Horsepower to 150% of base speed. NEMA Design B, Class F insulation, 1.0 Service Factor, 40 Degree C Ambient Blower on TEBC is 1 phase 50/60 Hz - 115 Volt input. Modifications available. Frame sizes 56-140T, W180T RPM AC: TEFC,TEBC and TENV Compact Vector Duty designs TEFC with 1000:1 constant torque range Totally enclosed, blower cooled (TEBC) complete with 3 phase 230/460 volt blower motor Totally enclosed non-ventilated (TENV) requires no fan or blower for cooling - Prevents entry of dust, grit or moisture - Available with XT (Extra Tough) features for severe environments in frames RL210 - L440 - Available in-line or piggy-back blower Wide speed range - 1000 : 1 constant torque, 2:1 constant horsepower - 100% Torque @ zero speed continuously High overload torque - 200% overload torque for 1 minute, base speed and below Designed to accept encoders, brakes and a full line of optional accessories - see modification and accessory pages Encoder provisions include machined opposite drive end flange and tapped hole for stub shaft First to meet and exceed NEMA MG-1 Part 31 specification for spike voltage withstand Encoder provisions include machined opposite drive end flange and tapped hole for stub shaft Three normally closed thermostats - one per phase Cast iron end brackets on RL210-L440 frames TEFC 1000:1 Constant Torque RL2162 Frame TENV TEBC M-191

Large AC RPM AC MOTORS Description Designed for optimum variable speed performance on AC controllers. The square laminated frame design achieves maximum adjustable speed performance. Ideal for use in demanding applications such as paper machines, machine tools, printing presses, extruders, cut-to-length, crane and hoist. All are suitable for full torque at zero speed continuously. Inverter Duty AC Motors RPM AC Inverter Duty TEFC Enclosure 1000:1 Constant Torque 5-250 HP TEFC Enclosure 200% overload - 1 minute base speed and below Top mounted conduit box standard (F-1, F-2 Option) Class H insulation Compact Low inertia Fast Response Optimized 4 pole design RL210 - L400 frames PLS lubrication in L280 - L400 frames Cast iron brackets Meets IP44 Drip-Proof Guarded Force Ventilated (DPGFV) 1000:1 Constant Torque 5-1000 HP 150% overload - 1 minute base speed and below F1 conduit box standard in RL210-L440 Class H insulation Most compact Lowest inertia Fast response Optimized 4 pole design (6 pole L440) RL210-L440 Frame PLS Lubrication in L280-L440 frames Cast iron brackets Meets IP23 Totally Enclosed Blower Cooled and Totally Enclosed Non-Ventilated 1000:1 Constant Torque 3-500 HP 200% overload - 1 minute base speed and below 2:1 constant HP (1) Top mounted conduit box standard RL210- L400 frames. F-1 on L440 frame Class H insulation Compact Low inertia Fast response Optimized 4 pole design (6 pole L440) RL210 - L440 Frame PLS Lubrication in L280-L440 frame Cast iron brackets Meets IP44 RPM III Medium DC Motors RPM XL Small DC Motors (1) See pricing and application sections for speed limitations General Information For pricing information or to place orders, go to www.ptplace.com M-192

RPM AC MOTORS Features 1000:1 constant torque Full continuous torque at zero speed Standard encoder provisions include machined bracket and tapped hole for stub shaft 40ì C Ambient - 1.0 Service Factor Stock encoder kits available for all ratings. See RPM AC Accessories Ball Bearing C-Face With Feet or Foot Mounted as shown - Without Encoder 1/3-1000HP HP 1/3 1/2 3/4 1 1.5 Notes: Speed, RPM Base CHP (1) Voltage Frame Enclosure Model Three normally closed thermostats (one per phase) Surpasses the requirements of NEMA MG-1 Part 31 for spike voltage withstand List Price Norm. Stock Notes Dimensions Sheet Design 3600 5400 230/460 FB56C TENV P56H6602 $343 N 610302-873 M2744 1.6/.8 3600 5400 230/460 FB56C TENV-EZ P56H6522 483 N 610302-877 M2744 1.6/.8 1800 3600 230/460 FB56C TENV P56H6605 350 Yes 610302-873 M4626F 1/.5 1800 3600 230/460 FB56C TENV-EZ P56H6525 490 N 610302-877 M4626 1/.5 1200 2400 230/460 FB56C TENV P56H6608 436 N 610302-873 M6717C 1.4/.7 1200 2400 230/460 FB56C TENV-EZ P56H6528 576 N 610302-877 M6717C 1.4/.7 3600 5400 230/460 FB56C TENV P56H6601 390 N 610302-873 M6711 1.6/.8 3600 5400 230/460 FB56C TENV-EZ P56H6521 530 N 610302-877 M6711 1.6/.8 1800 3600 230/460 FB56C TENV P56H6604 400 Yes 610302-873 M2941V 1.6/.8 1800 3600 230/460 FB56C TENV-EZ P56H6524 540 N 610302-877 M2941V 1.6/.8 1200 2400 230/460 FB56C TENV P56H6607 460 N 610302-873 M6718F 2./1 1200 2400 230/460 FB56C TENV-EZ P56H6527 600 N 610302-877 M6718F 2./1 3600 5400 230/460 FB56C TENV P56H6600 438 N 610302-873 M6712 2.2/1.1 3600 5400 230/460 FB56C TENV-EZ P56H6520 578 N 610302-877 M6712 2.2/1.1 1800 3600 230/460 FB56C TENV P56H6603 450 Yes 610302-873 M2966T 2.2/1.1 1800 3600 230/460 FB56C TENV-EZ P56H6523 590 N 610302-877 M2966T 2.2/1.1 1200 2400 230/460 FC56C TENV P56H6606 480 N 610302-873 M0149V 3/1.5 1200 2400 230/460 FC56C TENV-EZ P56H6526 620 N 610302-877 M0149V 3/1.5 3600 5400 230/460 WC143TC TENV P14A6900 516 N 610302-876 M6713 2.4/1.2 3600 5400 230/460 WC143TC TENV-EZ P14A6950 656 N 610302-879 M6713 2.4/1.2 1800 3600 230/460 WC143TC TENV P14A6903 460 Yes 610302-876 M2968Z 3.2/1.6 1800 3600 230/460 WC143TC TENV-EZ P14A6953 600 Yes 610302-879 M2968Z 3.2/1.6 1200 2400 230/460 WC143TC TENV P14A6906 540 N 610302-876 M8035V 3.6/1.8 1200 2400 230/460 WD143TC TENV-EZ P14A6956 680 N 610302-879 M8035V 3.6/1.8 3600 5400 230/460 WC143TC TENV P14A6901 660 N 610302-876 M6822 4./2 3600 5400 230/460 WD143TC TENV-EZ P14A6951 800 N 610302-879 M6822 4./2 1800 3600 230/460 WC143TC TENV P14A6904 480 Yes 610302-876 M8057 4.6/2.3 1800 3600 230/460 WC143TC TENV-EZ P14A6954 620 Yes 610302-879 M8057 4.6/2.3 1200 2400 230/460 WE145TC TENV P14A6907 640 N 610302-876 M8081V 4.4/2.2 1200 2400 230/460 WE145TC TENV-EZ P14A6957 780 N 610302-879 M8081V 4.4/2.2 For the current version of Inverter Duty Motors dimension sheets, connection diagrams, design curves, etc., go to www.reliance.com See delivery cycle sheet where N is shown above 4 week delivery based on non-modified model number shown, from date received at the plant.modifications may increase lead time. For motors with mounted encoder, (1/3-200 HP) See Page M-258 (*): Includes VPI, Stator RTDs, Grounding Brush, Insulated Bearing (O.D.E.), 3 thermostats. (2) Requires a minimum inverter carrier frequency of 4 Khz (1) CHP = Constant HP speed All L440 frames include VPI insulation and an insulated opposite drive end bearing. Price Symbol - RPMST FLA (59) M-193

RPM III Medium DC Motors RPM XL Small DC Motors RPM AC Inverter Duty Inverter Duty AC Motors Large AC RPM AC MOTORS 1000:1 Constant Torque 1/3-1000HP con t HP 2 3 5 7.5 Notes: Speed, RPM Base CHP (1) Voltage Frame Enclosure Model List Price Norm. Stock Notes Dimensions Sheet Design 3600 5400 230/460 WD145TC TENV P14A6902 $690 N 610302-876 M8082 5/2.5 3600 5400 230/460 WE145TC TENV-EZ P14A6952 830 N 610302-879 M8082 5/2.5 1800 3600 230/460 WD145TC TENV P14A6905 632 Yes 610302-876 M8058B 6./3 1800 3600 230/460 WD145TC TENV-EZ P14A6955 772 Yes 610302-879 M8058B 6./3 1150 2300 460 RL2153 TENV P21R335 2,332 4 weeks 617254-1 3 850 1700 460 RL2153 TENV P21R336 2,390 4 weeks 617254-1 3 650 1300 460 RL2153 TENV P21R337 2,465 4 weeks 617254-1 3 3600 5400 230/460 WE182TC TENV P18A8201 760 4 weeks 610302-880 M8052 7.2/3.8 3600 5400 230/460 WE182TC TENV-EZ P18A8251 900 4 weeks 610302-880 M8052 7.2/3.8 1800 3600 230/460 WE182TC TENV P18A8203 736 Yes 610302-880 M8070A 8.8/4.4 1800 3600 230/460 WE182TC TENV-EZ P18A8253 876 Yes 610302-880 M8070A 8.8/4.4 1150 2300 460 RL2153 TENV P21R338 2,440 4 weeks 617254-1 5 850 1700 460 RL2153 TENV P21R339 2,465 4 weeks 617254-1 5 650 1300 460 RL2153 TENV P21R340 2,590 4 weeks 617254-1 5 3600 5400 230/460 WE184TC TEBC P18A8102 930 4 weeks 610301-547 M4468 11.8/5.9 3550 4000 460 RL2153 TENV P21R341 2,355 4 weeks 617254-1 6.8 2500 5000 460 RL2153 TENV P21R386 3,370 4 weeks 617254-1 1800 3600 230/460 WE184TC TEBC P18A8204 880 Yes 610301-547 M4466AC 14.2/7.1 1750 3500 230/460 RL2153C TENV P21R307 2440 Yes 93 (180TC) 617254-33 L0060A 13.6/6.8 1150 2300 460 RL2158 TENV P21R342 2,595 4 weeks 617257-1 5 850 1700 460 RL2162 TENV P21R343 2,870 4 weeks 617200-1 8 850 1700 460 RL2153 TEBC P21R344 2,682 4 weeks 617255-1 8 650 1300 460 RL2153 TEBC P21R345 2,933 4 weeks 617255-1 8 650 1300 460 RL2173 TENV P21R256 2,980 4 weeks 617208-1 8 3550 4000 460 RL2153 TENV P21R346 2,490 4 weeks 617254-1 11 2500 5000 460 RL2153 TENV P21R387 3,538 4 weeks 617254-1 FLA (59) 1750 3500 230/460 RL2158C TENV P21R308 2,675 Yes 94 (210TC) 617257-3 L0056A 21.4/10.7 1150 2300 230/460 RL2162 TENV P21R347 2,854 4 weeks 617200-3 22/11 1150 2300 460 RL2153 TEBC P21R348 2,980 4 weeks 617255-1 11 850 1700 460 RL2158 TEFC P21R382 2,895 4 weeks 617255-1 11 850 1700 460 RL2153 TEBC P21R333 3,040 4 weeks 617255-1 11 850 1700 460 RL2173 TENV P21R257 3,205 4 weeks 617208-1 12 650 1000 460 RL2158 TEBC P21R349 3,439 4 weeks 617258-1 11 650 1300 460 RL2578 TENV P25R240 4,140 4 weeks 617216-1 12 For the current version of Inverter Duty Motors dimension sheets, connection diagrams, design curves, etc., go to www.reliance.com See delivery cycle sheet where N is shown above 4 week delivery based on non-modified model number shown, from date received at the plant.modifications may increase lead time. For motors with mounted encoder, (1/3-200 HP) See Page M-258 (*): Includes VPI, Stator RTDs, Grounding Brush, Insulated Bearing (O.D.E.), 3 thermostats. (2) Requires a minimum inverter carrier frequency of 4 Khz (1) CHP = Constant HP speed All L440 frames include VPI insulation and an insulated opposite drive end bearing. Price Symbol - RPMST General Information For pricing information or to place orders, go to www.ptplace.com M-194

RPM AC MOTORS 1000:1 Constant Torque 1/3-1000HP con t HP 10 15 Notes: Speed, RPM Base CHP (1) Voltage Frame Enclosure Model List Price Norm. Stock Notes Dimensions Sheet Design 3550 4000 230/460 RL2158 TENV P21R320 $2,680 4 weeks 617257-1 28/14 2500 5000 460 RL2158 TENV P21R350 3,775 4 weeks 617257-1 14 1750 3500 230/460 RL2162C TENV P21R309 2,788 Yes 94 (210TC) 617200-3 L0040A 28/14 1150 2300 460 RL2162 TEFC P21R329 3,095 4 weeks 617201-1 14 1150 2300 460 RL2158 TEBC P21R351 3,175 4 weeks 617258-1 14 1150 2300 460 RL2173 TENV P21R258 3,120 4 weeks 617208-1 14 850 1050 460 RL2153 DPG-FV P21R371 2,820 4 weeks 617256-1 14 850 1700 460 RL2162 TEFC P21R302 2,940 4 weeks 617201-1 14 850 1700 460 RL2158 TEBC P21R383 3,425 4 weeks 617258-1 14 850 1700 460 RL2578 TENV P25R271 3,730 4 weeks 617216-1 14 650 850 460 RL2158 DPG-FV P21R352 3,490 4 weeks 617259-1 14 650 1000 460 RL2168 TEBC P21R259 3,810 4 weeks 617205-1 14 650 1300 460 RL2586 TENV P25R241 4,540 4 weeks 617220-1 14 500 650 460 RL2162 DPG-FV P21R260 3,810 4 weeks 617202-1 14 3550 4000 460 RL2153 DPG-FV P21R353 2,860 4 weeks 617256-1 21 3550 4000 460 RL2153 TEBC P21R354 3,010 4 weeks 617255-1 21 3550 4000 230/460 RL2158 TENV P21R330 3,054 4 weeks 617257-1 42/21 2500 3600 460 RL2153 DPG-FV P21R355 2,935 4 weeks 617256-1 21 2500 5000 460 RL2153 TEBC P21R356 4,188 4 weeks 617255-1 21 2500 5000 460 RL2162 TENV P21R295 4,242 4 weeks 617200-1 21 1750 3500 460 RL2153 DPG-FV P21R357 2,680 4 weeks 617256-1 21 1750 3500 460 RL2158C TEFC P21R358 2,870 Yes 95 (250TC) 617258-13 L1517A 21 1750 3500 460 RL2153 TEBC P21R359 2,880 4 weeks 617255-1 21 1750 3500 460 RL2173 TENV P21R303 2,980 4 weeks 617208-1 L2401A 21 1150 1300 460 RL2153 DPG-FV P21R372 2,810 4 weeks 617256-1 21 1150 2300 460 RL2168 TEFC P21R296 3,145 4 weeks 617205-1 L2386A 21 1150 2300 460 RL2162 TEBC P21R360 3,267 4 weeks 617201-1 21 1150 2300 460 RL2586 TENV P25R243 3,692 4 weeks 617220-1 21 850 1050 460 RL2158 DPG-FV P21R361 3,125 4 weeks 617259-1 21 850 1700 460 RL2578 TEFC P25R284 3,290 4 weeks 617217-1 21 850 1700 460 RL2162 TEBC P21R297 3,760 4 weeks 617201-1 21 850 1700 460 L2882 TENV P28L240 7,980 N 616758-1 21 650 850 460 RL2162 DPG-FV P21R263 4,240 4 weeks 617202-1 21 650 1000 460 RL2173 TEBC P21R264 4,955 4 weeks 617209-1 21 650 1300 460 L2898 TENV P28L241 8,951 N 616758-1 21 500 650 460 RL2173 DPG-FV P21R265 4,820 4 weeks 617210-1 21 For the current version of Inverter Duty Motors dimension sheets, connection diagrams, design curves, etc., go to www.reliance.com See delivery cycle sheet where N is shown above 4 week delivery based on non-modified model number shown, from date received at the plant.modifications may increase lead time. For motors with mounted encoder, (1/3-200 HP) See Page M-258 (*): Includes VPI, Stator RTDs, Grounding Brush, Insulated Bearing (O.D.E.), 3 thermostats. (2) Requires a minimum inverter carrier frequency of 4 Khz (1) CHP = Constant HP speed All L440 frames include VPI insulation and an insulated opposite drive end bearing. Price Symbol - RPMST FLA (59) M-195

General Information RPM III Medium DC Motors RPM XL Small DC Motors RPM AC Inverter Duty Inverter Duty AC Motors Large AC RPM AC MOTORS 1000:1 Constant Torque 1/3-1000HP con t HP 20 25 Notes: Speed, RPM Base CHP (1) Voltage Frame Enclosure Model List Price Norm. Stock For pricing information or to place orders, go to www.ptplace.com Notes Dimensions Sheet Design 3550 4000 460 RL2153 DPG-FV P21R363 $3,048 4 weeks 617256-1 27 3550 4000 460 RL2153 TEBC P21R323 3,286 4 weeks 617255-1 27 3550 4000 460 RL2570 TENV P25R244 3,410 4 weeks 617212-1 27 2500 3600 460 RL2153 DPG-FV P21R362 3,110 4 weeks 617256-1 27 2500 3600 460 RL2158 TEFC P21R384 2,980 4 weeks 617258-1 27 2500 5000 460 RL2153 TEBC P21R364 4,530 4 weeks 617255-1 27 2500 5000 460 RL2173 TENV P21R298 4,860 4 weeks 617208-1 27 1750 2890 460 RL2153C DPG-FV P21R365 2,948 4 weeks 95 (250TC) 617256-13 27 1750 3500 460 RL2162C TEFC P21R283 2,990 Yes 95 (250TC) 617201-13 L0514A 27 1750 3500 460 RL2158C TEBC P21R314 3,005 Yes 95 (250TC) 617258-13 L0021A 27 1750 3500 460 RL2578 TENV P25R245 3,340 4 weeks 617216-1 L1876A 27 1150 1300 460 RL2162 DPG-FV P21R315 3,144 4 weeks 95 (250TC) 617259-13 27 1150 2300 460 RL2578 TEFC P25R285 3,380 4 weeks 617217-1 27 1150 2300 460 RL2168 TEBC P21R272 3,490 4 weeks 617205-1 L1756A 27 1150 2300 460 L2890 TENV P28L242 8,087 N 616758-1 27 850 1050 460 RL2162 DPG-FV P21R235 3,484 4 weeks 617202-1 27 850 1700 460 RL2586 TEFC P25R286 4,190 4 weeks 617221-1 27 850 1700 460 RL2173 TEBC P21R273 4,010 4 weeks 617209-1 27 850 1700 460 L2898 TENV P28L243 9,180 N 616758-1 27 650 850 460 RL2168 DPG-FV P21R274 4,655 4 weeks 617206-1 27 650 1000 460 RL2578 TEBC P25R246 5,787 4 weeks 617217-1 27 650 1300 460 L3203 TENV P32L263 11,688 N 616762-1 27 500 650 460 RL2570 DPG-FV P25R247 5,684 4 weeks 617214-1 27 3550 4000 460 RL2153 DPG-FV P21R366 3,252 4 weeks 617256-1 34 3550 4000 460 RL2153 TEBC P21R331 3,481 4 weeks 617255-1 34 3550 4000 460 RL2578 TENV P25R248 5,490 4 weeks 617216-1 34 2500 3600 460 RL2153 DPG-FV P21R367 3,312 4 weeks 617256-1 34 2500 3600 460 RL2162 TEFC P21R299 3,230 4 weeks 617201-1 34 2500 5000 460 RL2162 TEBC P21R385 4,755 4 weeks 617201-1 2500 5000 460 RL2578 TENV P25R249 7,340 4 weeks 617216-1 34 1750 2600 460 RL2158C DPG-FV P21R368 3,166 4 weeks 95 (250TC) 617259-13 34 1750 3550 460 RL2173C TEFC P21R286 3,288 Yes 95 (250TC) 617209-13 L1819A 34 1750 3500 460 RL2162C TEBC P21R287 3,240 Yes 95 (250TC) 617201-13 L0022A 34 1750 3500 460 RL2586 TENV P25R287 3,984 4 weeks 617220-1 L2402A 34 1150 1300 460 RL2162 DPG-FV P21R237 3,581 4 weeks 617202-1 L0349A 34 1150 2300 460 RL2586 TEFC P25R288 4,120 4 weeks 617221-1 34 1150 2300 460 RL2173 TEBC P21R275 3,925 4 weeks 617209-1 L1766A 34 1150 2300 460 L2898 TENV P28L245 9,144 N 616758-1 34 850 1050 460 RL2168 DPG-FV P21R276 4,010 4 weeks 617206-1 34 850 1700 460 L3203 TENV P32L264 11,155 N 616762-1 34 850 1700 460 RL2578 TEBC P25R250 4,910 4 weeks 617217-1 34 650 850 460 RL2570 DPG-FV P25R251 5,370 4 weeks 617214-1 34 650 1000 460 L2882 TEBC P28L246 9,105 N 616759-1 34 650 1000 460 L3213 TENV P32L265 12,995 N 616762-1 34 500 650 460 RL2586 DPG-FV P25R252 7,320 4 weeks 617222-1 34 For the current version of Inverter Duty Motors dimension sheets, connection diagrams, design curves, etc., go to www.reliance.com See delivery cycle sheet where N is shown above 4 week delivery based on non-modified model number shown, from date received at the plant.modifications may increase lead time. For motors with mounted encoder, (1/3-200 HP) See Page M-258 (*): Includes VPI, Stator RTDs, Grounding Brush, Insulated Bearing (O.D.E.), 3 thermostats. (2) Requires a minimum inverter carrier frequency of 4 Khz (1) CHP = Constant HP speed All L440 frames include VPI insulation and an insulated opposite drive end bearing. Price Symbol - RPMST FLA (59) M-196

RPM AC MOTORS 1000:1 Constant Torque 1/3-1000HP con t HP 30 40 Notes: Speed, RPM Base CHP (1) Voltage Frame Enclosure Model List Price Norm. Stock Notes Dimensions Sheet Design 3550 4000 460 RL2153 DPG-FV P21R317 $3,376 4 weeks 617256-1 40 3550 4000 460 RL2158 TEBC P21R328 3,745 4 weeks 617258-1 40 3550 3850 460 RL2586 TENV P25R289 5,940 4 weeks 617220-1 40 2500 3000 460 RL2153 DPG-FV P21R369 3,455 4 weeks 617256-1 40 2500 3550 460 RL2173 TEFC P21R300 3,440 4 weeks 617209-13 40 2500 4000 460 RL2586 TENV P25R290 6,165 4 weeks 617220-1 40 2500 5000 460 RL2162 TEBC P21R277 4,676 4 weeks 617201-1 L0181A 40 1750 3475 460 RL2158C DPG-FV P21R327 3,310 Yes 95 (250TC) 617259-13 L1206A 39 1750 3550 460 RL2578C TEFC P25R278 3,460 Yes 95 (250TC) 617217-13 L2380A 40 1750 3500 460 RL2162C TEBC P21R294 3,430 Yes 95 (250TC) 617201-13 L2381A 39 1750 3500 460 L2898 TENV P28L248 8,951 N 616758-1 40 1150 1350 460 RL2168 DPG-FV P21R250 4,290 Yes 617206-1 L1767A 38 1150 2300 460 RL2578 TEBC P25R253 4,685 4 weeks 617217-1 L1870A 40 1150 2300 460 L3203 TENV P32L236 11,240 N 616762-1 40 850 1050 460 RL2173 DPG-FV P21R278 4,435 4 weeks 617210-1 40 850 1500 460 RL2586 TEBC P25R291 5,511 4 weeks 617221-1 L2052A 40 850 1700 460 L3213 TENV P32L237 12,975 N 616762-1 40 650 850 460 RL2578 DPG-FV P25R255 6,620 4 weeks 617218-1 40 650 1000 460 L2890 TEBC P28L249 9,544 N 616759-1 40 650 1300 460 L4022 TENV P40L217 17,835 N 609995-1 40 500 650 460 RL2586 DPG-FV P25R256 7,660 4 weeks 617222-1 40 3550 4000 460 RL2158 DPG-FV P21R324 3,455 4 weeks 617259-1 52 3550 4000 460 RL2168 TEBC P21R279 4,130 4 weeks 617205-1 52 3550 3850 460 L2898 TENV P28L250 9,780 N 616758-1 52 2500 3000 460 RL2158 DPG-FV P21R370 3,573 4 weeks 617259-1 52 2500 2750 460 RL2578 TEFC P25R292 4,187 4 weeks 617217-1 52 2500 5000 460 RL2173 TEBC P21R280 6,775 4 weeks 617209-1 52 2500 3500 460 L3203 TENV P32L269 12,760 N 616762-1 52 1750 2000 460 RL2162 DPG-FV P21R211 3,550 Yes 617202-1 L0231A 52 1750 3550 460 RL2586 TEFC P25R279 3,765 Yes 617221-1 L1881A 52 1750 3500 460 RL2173 TEBC P21R285 3,580 Yes 617209-1 L2327A 52 1750 3500 460 L3203 TENV P32L238 11,240 N 616762-1 52 1150 1300 460 RL2168 DPG-FV P21R251 4,843 4 weeks 617206-1 L1814A 51 1150 2300 460 RL2586 TEBC P25R257 5,176 4 weeks 617221-1 L1871A 52 1150 2300 460 L3213 TENV P32L239 12,975 N 616762-1 52 850 1200 460 RL2578 DPG-FV P25R258 6,780 4 weeks 617218-1 53 850 1700 460 L2890 TEBC P28L252 8,842 N 616759-1 52 850 1700 460 L4022 TENV P40L218 17,100 N 609995-1 52 650 850 460 RL2586 DPG-FV P25R259 7,341 4 weeks 617222-1 52 650 1000 460 L2898 TEBC P28L253 10,200 N 616759-1 52 650 1300 460 L4022 TENV P40L219 17,235 N 609995-1 52 500 650 460 L2882 DPG-FV P28L254 9,780 N 616760-1 52 For the current version of Inverter Duty Motors dimension sheets, connection diagrams, design curves, etc., go to www.reliance.com See delivery cycle sheet where N is shown above 4 week delivery based on non-modified model number shown, from date received at the plant.modifications may increase lead time. For motors with mounted encoder, (1/3-200 HP) See Page M-258 (*): Includes VPI, Stator RTDs, Grounding Brush, Insulated Bearing (O.D.E.), 3 thermostats. (2) Requires a minimum inverter carrier frequency of 4 Khz (1) CHP = Constant HP speed All L440 frames include VPI insulation and an insulated opposite drive end bearing. Price Symbol - RPMST FLA (59) M-197

RPM III Medium DC Motors RPM XL Small DC Motors RPM AC Inverter Duty Inverter Duty AC Motors Large AC RPM AC MOTORS 1000:1 Constant Torque 1/3-1000HP con t HP 50 60 Notes: Speed, RPM Base CHP (1) Voltage Frame Enclosure Model List Price Norm. Stock Notes Dimensions Sheet Design 3550 4000 460 RL2162 DPG-FV P21R325 $4,420 4 weeks 617202-1 65 3550 4000 460 RL2173 TEBC P21R266 5,308 4 weeks 617209-1 65 3550 3850 460 L2898 TENV P28L255 12,087 N 616758-1 65 2500 3600 460 RL2168 DPG-FV P21R267 4,515 4 weeks 617206-1 65 2500 2750 460 RL2586 TEFC P25R293 4,465 4 weeks 617221-1 L2400A 65 2500 5000 460 RL2173 TEBC P21R301 7,282 4 weeks 617209-1 65 2500 3500 460 L3203 TENV P32L240 12,980 N 616762-1 65 1750 2000 460 RL2168 DPG-FV P21R254 3,960 Yes 617206-1 L1757A 65 1750 3500 460 RL2578 TEBC P25R234 4,620 Yes 617217-1 L1823A 61 1750 3500 460 L3203 TENV P32L241 11,365 N 616762-1 65 1150 1300 460 RL2570 DPG-FV P25R217 5,730 Yes 617214-1 L0191A 65 1150 2300 460 L2882 TEBC P28L256 8,680 N 616759-1 65 1150 2300 460 L4022 TENV P40L220 17,370 N 609995-1 65 850 1050 460 RL2578 DPG-FV P25R261 7,160 4 weeks 617218-1 69 850 1700 460 L2898 TEBC P28L257 9,641 N 616759-1 65 850 1700 460 L4034 TENV P40L221 18,973 N 609995-1 65 650 850 460 L2882 DPG-FV P28L258 10,440 N 616760-1 65 650 1000 460 L3213 TEBC P32L242 12,810 N 616763-1 65 650 1300 460 L4034 TENV P40L222 22,302 N 609995-1 65 500 650 460 L2898 DPG-FV P28L259 11,300 N 616760-1 65 3550 4000 460 RL2168 DPG-FV P21R268 4,945 4 weeks 617206-1 77 3550 4000 460 RL2578 TEBC P25R262 6,240 4 weeks 617217-1 77 3550 3850 460 L3203 TENV P32L243 12,200 N 616762-1 77 2500 3000 460 RL2168 DPG-FV P21R269 4,610 4 weeks 617206-1 77 2500 3500 460 L3213 TENV P32L244 13,444 N 616762-1 77 2500 5000 460 RL2578 TEBC P25R263 8,421 4 weeks 617217-1 77 1750 2200 460 RL2168 DPG-FV P21R247 4,780 Yes 617206-1 L1765A 74 1750 3500 460 RL2586 TEBC P25R232 5,980 Yes 617221-1 L1820A 74 1750 3500 460 L3607 TENV P36L224 16,912 N 609995-1 77 1150 1300 460 RL2578 DPG-FV P25R237 6,970 Yes 617218-1 L1866A 73 1150 2300 460 L2898 TEBC P28L260 9,240 N 616759-1 77 1150 2300 460 L4034 TENV P40L223 19,494 N 609995-1 77 850 950 460 RL2586 DPG-FV P25R264 8,155 4 weeks 617222-1 77 850 1700 460 L3203 TEBC P32L245 10,320 N 616763-1 77 850 1700 460 L4046 TENV P40L224 21,400 N 609995-1 77 650 900 460 L2890 DPG-FV P28L261 11,360 N 616760-1 77 650 1000 460 L4022 TEBC P40L206 19,800 N 609994-1 77 500 650 460 L2898 DPG-FV P28L262 12,520 N 616760-1 77 For the current version of Inverter Duty Motors dimension sheets, connection diagrams, design curves, etc., go to www.reliance.com See delivery cycle sheet where N is shown above 4 week delivery based on non-modified model number shown, from date received at the plant.modifications may increase lead time. For motors with mounted encoder, (1/3-200 HP) See Page M-258 (*): Includes VPI, Stator RTDs, Grounding Brush, Insulated Bearing (O.D.E.), 3 thermostats. (2) Requires a minimum inverter carrier frequency of 4 Khz (1) CHP = Constant HP speed All L440 frames include VPI insulation and an insulated opposite drive end bearing. Price Symbol - RPMST FLA (59) General Information For pricing information or to place orders, go to www.ptplace.com M-198