HSC HSC Full Size Solenoid Locking Switches Key features: Rugged aluminum die-cast housing 00N locking retention force Flexible Installation: The actuator can be accessed from two directions Select from four different circuit configurations IP HSC Series Functionality LED (green or red) Manual Unlocking Entry (M hole) Accessible using a small screwdriver after removing a TORX screw on the unlocking entry Part Numbers (Mechanical Spring Lock Only) Two Conduit Ports (G/) Use IP conduit or gland Tubular Clamp Terminal Block (M) Terminal Block (M.) Ground Terminal (M) Two Entry Slots TORX is a registered trademark of Camcar Textron. Contact Configuration LED Part Number Contact Configuration LED Part Number HSC-RR-G + HSC-RR-G Red HSC-RR-R Red HSC-RR-R HSC-RR-G + HSC-RR-G Red HSC-RR-R Red HSC-RR-R 00--IDEC () USA & Canada
HSC Solenoid Locking Safety Switches Overview Keys & Accessories Appearance Part Number Description Appearance Part Number Description HS9Z-A Straight HS9Z-T Key Wrench (included with switch) HS9Z-A Right-angle HS9Z-P Conduit Opening Plug (G/) Light Curtains Safety Control Relays Enabling Switches Interlock Switches XW Series E-Stops HS9Z-A Adjustable Specifications Conforming to Standards EN0, IEC09--, EN09--, GS-ET-9, UL0, GB 0. (CCC approval), CSA C. No. Operating Temperature 0 to +0 C (no freezing) Storage Temperature 0 to +0 C Relative Humidity 0 to % (no condensation) Altitude,000m maximum Rated Insulation Voltage (U i ) 00V (between LED or solenoid and ground: 0V) Impulse Withstand Voltage (U imp ) kv (between LED or solenoid and ground:. kv) Between live and dead metal parts: 00 MΩ minimum Insulation Resistance Between live metal part and ground: 00 MΩ minimum Between live metal parts: 00 MΩ minimum Between terminals of the same pole: 00 MΩ minimum Electric Shock Protection Class Class (IEC0) Pollution Degree (IEC09--) Degree of Protection IP (IEC09) Vibration Operating Extremes 0 to Hz, amplitude 0. mm Resistance Damage Limits 0 m/sec (approx. G) Shock Resistance,000 m/s (approx. 00G) Retention Force,00N minimum Operating Speed 0.0 to.0m/s Direct Opening Travel mm minimum Direct Opening Force 0N minimum Thermal Current (I th ) Main circuit: 0A, Auxiliary circuit: A Contact Opening Distance Main circuit:. mm max., Auxiliary circuit:. mm min. Operating Frequency 900 operations/hour max. Mechanical Life,000,000 operations Electrical Life 00,000 operations (rated load) Conditional Short-circuit Current 00A (IEC09--) Recommended Short Circuit Protection 0V, 0A fuse (Type D0 based on IEC09-, 09-) AS-Interface Safety at Work www.idec.com
HSC Specifications, con t Operating Voltage V DC (00% duty cycle) Current ma (initial value) Coil Resistance Ω (at 0ºC) Solenoid Unit Energizing Voltage Rated voltage x % maximum (at 0ºC) De-energizing Voltage Rated voltage x 0% minimum (at 0ºC) Continuous Applicable Voltage Rated voltage x 0% Insulation Class Class B Operating Voltage V DC Current 0 ma Light Source LED lamp Lens Color Red or Weight (approx.) 0g Contact Ratings Rated Operating Current (Ie) Operating Voltage (Ue) 0V V 0V AC Resistive load (AC) 0A 0A A Inductive load (AC) 0A A A DC Resistive load (DC) A Inductive load (DC) A 0.9A AC Resistive load (AC) A A Inductive load (AC) A DC Resistive load (DC) A Inductive load (DC) 0.9A Main Circuit Auxiliary Circuit 00--IDEC () USA & Canada
HSC Solenoid Locking Safety Switches Dimensions (mm) HSC-RR-* - using the straight actuator (HS9Z-A) AS-Interface Safety at Work Interlock Switches Light Curtains Safety Control Relays Enabling Switches XW Series E-Stops Overview HSC-RR-* - using the Right-angle actuator (HS9Z-A) www.idec.com
HSC Accessories Straight (mainly for sliding doors) HS9Z-A Adjustable -M Screws Mounting Holes R. 0. 9 9. 9. 9. Cover (red) The actuator angle is adjustable (0 to 0 ) for hinged doors. The minimum radius of the door opening can be as small as 00mm. For HS/HS Series (HS9Z-A) Applicable Crimping Terminals max. () 0. (Note) Stop Film (attached) 9. 0 R. Right-angle (mainly for hinged doors) HS9Z-A Angle Adjustment Screw (M hexagon socket head screw) 0 All dimensions in mm. (Refer to the Crimping Terminal or shown in the drawing below.) HSC Terminals No. to : Use solid or stranded wires only (crimping terminals not applicable). Terminals No. and : Crimping Terminal Ground Terminal: Crimping Terminal HSB Ground Terminal: Crimping Terminal Other Terminals: Crimping Terminal HSB, HSB, and HSE Crimping Terminal *After installing the actuator, remove the actuator cover. Door hinge -M Screws Mounting Holes. min.. max. ø. min..9 max. Crimping Terminal Mounting Holes -M Screws Use an insulation tube on the crimping terminal. Wire Approx. mm Insulation Tube R. 0. 0. 90. min.. max. ø. min.. max. Crimping Terminal Crimping Terminal. 9. Cover (red). 00--IDEC () USA & Canada