-Series Circuit Breaker The -Series hydraulic/magnetic circuit breaker provides dependable circuit protection in a low cost, compact package. By meeting the IEC spacing requirements, the -Series is the ideal choice for international market applications. It also features a trip-free mechanism, which will open the contacts when a fault condition occurs, even if the handle is held in the ON position. Although a low cost option, the -Series was designed for maximum performance and reliable equipment protection meeting Carling s stringent quality standards. Key Features & Benefits: Choice of actuator styles U0, CCC, CSA, C. and EN09 approvals Compact size Temperature stable operation -0 o c to 0 o c Choice of terminals, including PCB Single or multi-pole configurations CURVED ROCKER ACTUATOR ANDE ACTUATOR FAT WIT PUS TO RESET ACTUATOR CURVED ROCKER WIT GUARD
-Series General Specifi ations Electrical Tables Table A: ists U Recognized, CSA Accepted and TUV Certified configurations and performance capabilities as a Component Supplementary Protector. SERIES - COMPONENT SUPPEMENTARY PROTECTOR CIRCUIT VOTAGE CURRENT SORT CIRCUIT CAPACITY (AMPS) CONFIGURATION MAX U CSA TUV APPICATION CODES RATING FREQ. PASE FU MINIMUM POES WITOUT BACKUP FUSE WITOUT BACKUP FUSE WITOUT BACKUP FUSE U CSA DC -- - 000 000 00(PC) TC, O, U TC, O, U DC -- - --- 00 --- --- TC, O, U 0 DC -- - 000 00 000(PC) TC, O, U TC, O, U SERIES 0 DC -- - 000 000 000(PC) TC, O, U TC, O, U 0 0/0-00 00 000(PC) TC, O, U TC, O, U 0 0/0-00 00 000(PC) TC, O, U TC, O, U 0 0/0-00 00 000(PC) TC, O0, U TC, O0, U - Polarity Sensitive Electrical Maximum Voltage Current Rating Auxiliary Switch Rating Mechanical Endurance Physical Number of Poles Weight Internal Circuit Config. Agency Approvals 0VAC 0/0z 0 VDC Standard current coils:.00,.0,.00,.0, 0.0,.0, 0.0,.0, 0.0,.0 SPDT: 0.A-0VAC,.0A-VDC/0.A-0VDC, 0.A-VAC (with gold contacts) 0,000 ON-OFF operations @ per minute; with rated current & voltage - Approx. grams/pole (. oz) Series and Switch Only (with or without auxiliary switch) U Recognized under the Component Recognition Program as Protectors, Supplementary (Guide QVNU File E9) U standard 0 Typical Protector Resistance DCR and Impedance values are based on measurements by the voltmeter ammeter method. Rated current is applied for one hour and at a voltage t less than 0 volts. Ambient temperature: ; Tolerance: Below 0 amps +/- %; Above 0 amps +/-% Impedance Chart Current rating in amperes DC-Ohms Series 0/0z-Ohms 0. 0.. 0. 0. 0.0 0.0. 0.0 0.09 0 0.0 0.0 0.00 0.00 0 0.00 0.00 0.00 0.00 0 0.00 0.00 CCC certified, Certificate No. 000009 CSA Accepted Circuit Breaker, CSA standard C. No. TUV certified to EN09, Certificate No. R000 *Manufacturer reserves the right to change product specification without prior tice.
-Series Dimensional Specifi ations: in. [mm] andle Actuator
-Series Dimensional Specifications: in. [mm] Curved Rocker Actuator #-[M] TREAD *0.[.0] DEEP PCS PER POE 0. [.0] 0. [.00] -POE (J). [.0]. [.].0 [.0]. [.90]. [.00] 0. [.0] 0.0 [.] MAX 0. [9.0]. [.00]. [9.] TAB(Q.C.)TYPE. [9.] SCREW TYPE SCREW TYPE TEMINAS IN SERIES TRIP CIRCUIT CONFIGURATION SOWN. FOR OTERS CONFIGURATIONS, SEE CIRCUIT AND TERMINA DIAGRAMS.. [.] 0. [.0] 0. [0.0] -POE (J).0 [.0].0 [.0] 0.0 [.00] OPTIONA "ROCKER GUARD".0 [.] MAX.9 [0.0] -POE (J).9 [.0] C ON NC.99 [9.00] MAX 0.0 [.00] TYP 0. [9.] -Ø0. [Ø.9] 0. [.99]. [.0]. [9.] POE POE POE MUTI-POE IDENTIFICATION SCEME AS VIEWED FROM TERMINA END OF BREAKER. NOTES:. A DIMENSIONS ARE IN INCES [mm]. TOERANCE +.00 [.] UNESS OTERWISE SPECIFIED. 0.0 [.] PANE CUTOUT DETAI TOERANCE +.00[ +.] UNESS OTERWISE SPECIFIED
-Series Dimensional Specifications: in. [mm] Flat Rocker Actuator PUS-TO-RESET ACTUATOR #-[M] TREAD *0.[.0] DEEP PCS PER POE 0. [.00] 0. [.00] -POE () 0. [.0] 0. [.0]. [.0]. [.0] 0.0 [.] MAX 0.0 [.] MAX. [.]. [.].0 [.0].0 [.0] 0.9 [9.] 0. [9.0] 0.9 [9.] 0. [9.0]. [.00].. [9.] [.00] TAB(Q.C.)TYPE. [9.] TAB(Q.C.)TYPE. [9.] SCREW TYPE. [9.] SCREW TYPE. [.90]. [.90]. [.00]. [.00] SCREW TYPE TEMINAS IN SERIES TRIP CIRCUIT CONFIGURATION SOWN. FOR OTERS CONFIGURATIONS, SEE CIRCUIT AND TERMINA DIAGRAMS. -POE (). [.0]. [.0]. [.]. [.].0 [.0].0 [.0] 0. [.00] 0. [.00] 0. [.0] 0. [.0] 0.0 [.] 0.9 [9.] MAX 0.0 [.] 0.9 [9.]. [.] MAX 0. [.0]. [.] 0. [.0] -POE ().0 [.0].0 [.0].0 [.0].0 [.0] 0.0 [.00].0 [.] MAX 0.0 [.00].0 [.] MAX.9 [0.0].9 [0.0].9 [0.0] -POE ().99 [9.00] MAX.99 [9.00].99 MAX [9.00] MAX 0.0 [.00] TYP 0.0 [.00] 0.0 TYP [.00] TYP.9 [.0].9 [.0].9 [.0] 0. [9.] 0. [9.] 0. [9.] -Ø0. [Ø.9] -Ø0. [Ø.9] 0. [.99] 0. [.99] -Ø0. [Ø.9] 0. [.99]. [.0]. [.0]. [9.]. [9.]. [.0]. [9.] 0.0 [.] 0.0 [.] 0.0 [.] MUTI-POE IDENTIFICATION SCEME AS VIEWED FROM TERMINA END OF BREAKER. NOTES:. A DIMENSIONS ARE IN INCES [mm]. TOERANCE +.00 [.] UNESS OTERWISE SPECIFIED. PANE CUTOUT DETAI TOERANCE +.00[ +.] UNESS OTERWISE SPECIFIED
-Series Dimensional Specifications: in. [mm] PC Teminals PRINTED CIRCUIT BOARD MOUNTING TERMINA CODE R PRINTED CIRCUIT BOARD MOUNTING TERMINA CODE PRINTED CIRCUIT BOARD MOUNTING TERMINA CODE S & T NOTES:. A DIMENSIONS ARE IN INCES [mm]. TOERANCE +.00 [.] UNESS OTERWISE SPECIFIED.
-Series Dimensional Specifications: in. [mm] PC Teminals P.C. FOOT PRINT FOR TERMINA CODE R P.C. FOOT PRINT FOR TERMINA CODE P.C. FOOT PRINT FOR TERMINA CODE S & T NOTES:. A DIMENSIONS ARE IN INCES [mm]. TOERANCE +.00 [.] UNESS OTERWISE SPECIFIED.
-Series Dimensional Specifications: in. [mm] Circuit & Terminal CIRCUIT BREAKER MODE ANDE POSITION VS. AUX SWITC MODE STANDARD C/B ANDE POSITION AUX. SWITC MODE OFF 0 OFF NC NO C ON ON 0 NC NO C EECTRICA TRIP 0 OFF O NC NO C 0. [.0] 0. [.0] TERMINA DIMENSIONA DETAI & RATING 0. [.0] 0.9 [.9] 0. [9.9] 0.0 [.0] 0.0 [0.] 0.0 [.0] Ø0.0 [Ø.] TAB (Q.C.) 0.0 [.] 0. [9.00] UPTURN UG 0. [9.00] BUS 0. [.9] 0.9 [.00] 0.0 [.0] 0.9 [.00] 0. [.00] 0.9 [.00] 0. [.00] P.C. TERMINA P.C. TERMINA P.C. TERMINA 90 FACING EFT STRAIGT (SORT) STRAIGT (ONG) 90 FACING RIGT.9 [0.0] BARRIER FOR U-RECOGNIZED MUTI-POE BREAKERS.0 [.0].9 [.00] TABE A TIGTENING TORQUE SPECIFICATIONS TREAD SIZE #- & M MOUNTING ARDWARE #- & M TREAD TERMINA SCREW TABE B TORQUE -9 IN-BS [0.-.0 NM] - IN-BS [.-. NM] DEPT TERMINA DESCRIPTION BEIND PANE TAB (Q.C.).99 [0.0] MAIN SCREW TYPE.99 [0.0].0 TAB (Q.C.). [.] AUX. SWITC* SODER TYPE. [.9] SEE TABE B. [.0] * AVAIABE ON SERIES TRIP AND SWITC ONY CIRCUITS. WEN CAED FOR ON MUTI-POE UNITS, ONY ONE AUX. SWITC IS NORMAY SUPPIED, AS SOWN IN MUTI-POE IDENTIFICATION SCEME.. [.90]. [.90].0 [.0]. [.00] REF 0.0 [.0] 0.0 [0.0]. A DIMENSIONS ARE IN INCES [mm]. TOERANCE ±.00 [.] UNESS OTERWISE SPECIFIED.
-Series Dimensional Specifications: in. [mm] Circuit & Terminal 9 B,C B,C G
0 -Series Time Delay Values PERCENT OF RATED CURRENT NOTES: Delay Curves,,,,,,,: Breakers to hold 00% and must trip at % of rated current and greater within the time limit shown in this curve. Delay Curves 0,0: Breakers to hold 00% and must trip at 0% of rated current and greater within the time limit shown in this curve. All Curves: Curve data shown represents breaker response at ambient temperature of F ( C) with preloading. Breakers are mounted in standard wall-mount position. The minimum inrush pulse tolerance handling capability is times the rated current. These values are based on a 0 z / cycle,. ms pulse. Instantaneous AC DC Ultrashort Short
-Series Time Delay Values Medium AC DC ong Short igh Inrush AC igh Inrush DC Medium ong
-Series andle Actuator Ordering Scheme A B 0 0 B D C Series Actuator Poles Circuit Aux/Alarm Switch Frequency & Delay Current Rating Terminal 9 Actuator Color & egend 0 Mounting Bezel/Barrier Rating Agency Approval SERIES ACTUATOR A andle, one per pole B andle, one per unit TERMINA Push ON 0.0 Tab (Q.C.) Screw - w/upturned lugs Screw - (bus type) A Screw M w/upturned lugs B Screw M (bus type) R S T Printed Circuitboard Terminals 90 Facing eft 90 Facing Right Straight Straight, ong POE One Two Three CIRCUIT A Switch Only ( coil) B Series Trip (current) AUXIIARY/AARM SWITC 0 w/o Aux Switch 0.0 Q.C. term 0.0 Solder ug FREQUENCY & DEAY 0 DC 0/0z, Switch Only 0 DC Instantaneous DC Ultra Short DC Short DC Medium DC ong 0 0/0z Instantaneous 0/0z Ultra Short 0/0z Short 0/0z Medium 0/0z ong C G Series Trip (voltage) Relay Trip (voltage) 0.0 Q.C. term w/ gold contacts 0.0 PC term 0 DC, 0/0z, Instantaneous DC, 0/0z,Ultra Short DC, 0/0z, Short DC, 0/0z, Medium DC, 0/0z, ong 0/0z Short, i-inrush 0/0z Medium, i-inrush 0/0z ong, i-inrush DC Short, i-inrush DC Medium, i-inrush DC ong, i-inrush 9 ACTUATOR COOR & EGEND Actuator Color Red Green Blue Yellow Orange I-O A C F K M P R ON-OFF B D G J N Q S 0 MOUNTING/BARRIERS MOUNTING STYE A B C D Threaded Insert BARRIERS MAX. APPICATION RATING A DC D 0AC M 0DC Dual BEZE domed domed domed domed flat flat flat flat egend Color 0VDC/0VAC CURRENT RATING (AMPERES) CODE AMPERES 0.000.0.00.0 0.000.0.00.0 0.000.00 VOTAGE RATING CODE RATING TRIP VOTS A0 DC DC A DC 0DC A DC DC A DC 0DC A DC DC A DC 0DC 0.000.00 0.000.00 0.000.00 0.000.00 0.000.00 90 9.000 9 9.00 0 0.000 0 0.00.000.00.000.00.000.000 A DC DC J0 AC AC J AC 0AC J AC AC J AC 0AC J AC 0AC.000.000.000.000 0 0.000.000.000.000 0 0.000.000 J AC AC K0 0AC AC 0 0AC 0AC B0 0DC 9DC B0 0DC DC AGENCY APPROVA A Without approvals C U Recognized, CSA Accepted, CCC Certified E U Recognized, CSA Accepted, TUV Certified U Recognized, CSA Accepted, TUV Certified, CCC Certified Notes: Actuator Option A: handle tie pin, spacer & retainers provided unassembled on multipole units. Actuator Option B: andle location as viewed from front of panel: pole: left pole; pole: center pole Standard multipole units have all poles identical, except when specifying auxiliary switch Auxiliary switch available on Series Trip and Switch Only circuits to A. On multipole units, only one aux. switch is rmally supplied, mounted in extreme right pole. Separate Pole Type Voltage Coils t rated for continuous duty. Available only with delay code 0 & 0. Only Available w/ Agency code C. For other current ratings, consult factory. -A Polarity sensitive, only available as pole unit. Voltage code available to A max.
-Series Curved Rocker Actuator Ordering Scheme J B 0 0 0 B D C Series Actuator Poles Circuit Aux/Alarm Switch Frequency & Delay Current Rating Terminal 9 Actuator Color & egend 0 Mounting Bezel/Barrier Rating Agency Approval SERIES (VISI ROCKER) ACTUATOR J Vertical - Indicate OFF K Vertical - Indicate ON TERMINA Push ON 0.0 Tab (Q.C.) Screw - w/upturned lugs Screw - (bus type) A Screw M w/upturned lugs B Screw M (bus type) R S T Printed Circuitboard Terminals 90 Facing eft 90 Facing Right Straight Straight, ong POE One Two Three CIRCUIT A Switch Only ( coil) B Series Trip (current) AUXIIARY/AARM SWITC 0 w/o Aux Switch 0.0 Q.C. term 0.0 Solder ug FREQUENCY & DEAY 0 DC 0/0z, Switch Only 0 DC Instantaneous DC Ultra Short DC Short DC Medium DC ong 0 0/0z Instantaneous 0/0z Ultra Short 0/0z Short 0/0z Medium 0/0z ong CURRENT RATING (AMPERES) CODE AMPERES 0.000.0.00.0 0.000.0.00.0 0.000.00 0.000.00 VOTAGE RATING CODE RATING TRIP VOTS A0 DC DC A DC 0DC A DC DC A DC 0DC A DC DC A DC 0DC 0.000.00 0.000.00 0.000.00 0.000.00 90 9.000 9 9.00 0 0.000 0 0.00 C G Series Trip (voltage) Relay Trip (voltage) 0.0 Q.C. term w/ gold contacts 0.0 PC term 0 DC, 0/0z, Instantaneous DC, 0/0z,Ultra Short DC, 0/0z, Short DC, 0/0z, Medium DC, 0/0z, ong 0/0z Short, i-inrush 0/0z Medium, i-inrush 0/0z ong, i-inrush DC Short, i-inrush DC Medium, i-inrush DC ong, i-inrush.000.00.000.00.000.000.000.000.000.000 9 9.000 0 0.000 A DC DC J0 AC AC J AC 0AC J AC AC J AC 0AC J AC 0AC.000.000.000.000.000.000.000.000 9 9.000 0 0.000.000 J AC AC K0 0AC AC 0 0AC 0AC B0 0DC 9DC B0 0DC DC 9 ACTUATOR COOR & EGEND Actuator Color Red Green Blue Yellow Orange I-O A F K M P R ON-OFF B G J N Q S 0 MOUNTING/BARRIERS MOUNTING STYE A B C D E F G 9 J P K Q U M Threaded Insert BARRIERS Dual AF ROCKER GUARD BRACKET COOR MAX. APPICATION RATING A DC D 0AC M 0DC 0VDC/0VAC AGENCY APPROVA A Without approvals C U Recognized, CSA Accepted E U Recognized, CSA Accepted, TUV Certified U Recognized, CSA Accepted, TUV Certified, CCC Certified FIG.B FIG. C Notes: alf guard construction have OFF protection for actuator Standard multipole units have all poles identical, except when specifying auxiliary switch Auxiliary switch available on Series Trip and Switch Only circuits to A. On multipole units, only one aux. switch is rmally supplied, mounted in extreme right pole. Separate Pole Type Voltage Coils t rated for continuous duty. Available only with delay code 0 & 0. Only Available w/ Agency code C. For other current ratings, consult factory. On Visi-Rocker,Visi portion of rocker cant be the same color as the bezel. Remainder of rocker same color as bezel. -A Polarity sensitive, only available as pole unit. Voltage code available to A max.
-Series Flat Rocker Actuator Ordering Scheme B 0 0 0 B D C Series Actuator Poles Circuit Aux/Alarm Switch Frequency & Delay Current Rating Terminal 9 Actuator Color & egend 0 Mounting Bezel/Barrier Rating Agency Approval SERIES ACTUATOR Single Color Vertical Single Color orizontal Push to Reset, Single Color Vertical Push to Reset, Single Color orizontal TERMINA Push ON 0.0 Tab (Q.C.) Screw - w/upturned lugs Screw - (bus type) A Screw M w/upturned lugs B Screw M (bus type) R S T Printed Circuitboard Terminals 90 Facing eft 90 Facing Right Straight Straight, ong POE One Two Three CIRCUIT A Switch Only ( coil) B Series Trip (current) AUXIIARY/AARM SWITC 0 w/o Aux Switch 0.0 Q.C. term 0.0 Solder ug FREQUENCY & DEAY 0 DC 0/0z, Switch Only 0 DC Instantaneous DC Ultra Short DC Short DC Medium DC ong 0 0/0z Instantaneous 0/0z Ultra Short 0/0z Short 0/0z Medium 0/0z ong CURRENT RATING (AMPERES) CODE AMPERES 0.000.0.00.0 0.000.0.00.0 0.000.00 0.000.00 VOTAGE RATING CODE RATING TRIP VOTS A0 DC DC A DC 0DC A DC DC A DC 0DC A DC DC A DC 0DC 0.000.00 0.000.00 0.000.00 0.000.00 90 9.000 9 9.00 0 0.000 0 0.00 C G Series Trip (voltage) Relay Trip (voltage) 0.0 Q.C. term w/ gold contacts 0.0 PC term 0 DC, 0/0z, Instantaneous DC, 0/0z,Ultra Short DC, 0/0z, Short DC, 0/0z, Medium DC, 0/0z, ong 0/0z Short, i-inrush 0/0z Medium, i-inrush 0/0z ong, i-inrush DC Short, i-inrush DC Medium, i-inrush DC ong, i-inrush.000.00.000.00.000.000.000.000.000.000 9 9.000 0 0.000 A DC DC J0 AC AC J AC 0AC J AC AC J AC 0AC J AC 0AC.000.000.000.000.000.000.000.000 9 9.000 0 0.000.000 J AC AC K0 0AC AC 0 0AC 0AC B0 0DC 9DC B0 0DC DC X0 AC special catalog # 9 ACTUATOR COOR & EGEND Actuator Color Red Green Blue Yellow Orange I-O A C F K M P R ON-OFF B D G J N Q S 0 MOUNTING/BARRIERS MOUNTING STYE A B C D E F G 9 J P K Q U M Threaded Insert BARRIERS Dual PUS-TO- RESET egend Color BRACKET COOR MAX. APPICATION RATING A DC D 0AC M 0DC 0VDC/0VAC AGENCY APPROVA A Without approvals C U Recognized, CSA Accepted, CCC Certified E U Recognized, CSA Accepted, TUV Certified U Recognized, CSA Accepted, TUV Certified, CCC Certified FIG.B FIG. C Notes: Push-To-Reset actuator shave OFF portion of rocker shrounded Standard multipole units have all poles identical, except when specifying auxiliary switch Auxiliary switch available on Series Trip and Switch Only circuits to A. On multipole units, only one aux. switch is rmally supplied, mounted in extreme right pole. Separate Pole Type Voltage Coils t rated for continuous duty. Available only with delay code 0 & 0. Only Available w/ Agency code C. For other current ratings, consult factory. On Visi-Rocker,Visi portion of rocker cant be the same color as the bezel. Remainder of rocker same color as bezel. -A Polarity sensitive, only available as pole unit. Voltage code available to A max.