Rotary Cutter RC(M)4620 39216 331-936P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 07/10/18 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Decks & Hitches...6 Deck Center Components...6 Deck Center Drive Components...8 Deck Wing Components...10 Deck Wing Drive Components...12 Hitch A-Frame...14 Hitch Ball Coupler...16 Hitch Bar Tite...18 Hitch LP Performance...20 Hitch Pintle...22 Hitch Standard Pivoting Clevis...24 Leveling Rod...26 Lights 5 Inch (LED)...28 Section 3: Axles...30 Axle Center...30 Axle Wing...32 Hub Assembly (330-938K)...34 Tire Options...36 Section 4: Guards...38 Guards Chain Double Row Front...38 Guards Chain Double Row Rear...40 Guards Chain Single Row Front...42 Guards Chain Single Row Rear...44 Section 5: Drivelines...46 Driveline Center (826-820C) Comer...46 Driveline Conv. 1000 RPM (826-247C) Walterscheid...48 Driveline Conv. 540 RPM (826-112C) Walterscheid...50 Driveline CV 38 1000 RPM (826-644C) Weasler...52 Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler...54 Driveline CV 75 1000 RPM (826-645C)...56 Driveline CV 540 RPM (826-643C) Weasler...58 Driveline Wing (826-819C) Comer...60 Section 6: Gearboxes...62 Divider Box 1000 RPM 35:1 (826-709C)...62 Divider Box 540 RPM 1:35 (826-708C)...64 Gearbox (826-840C)...66 Gearbox (826-841C)...68 Gearbox 1000 RPM (826-626C) Comer...70 Gearbox 540 RPM (826-316C)...72 Section 7: Hydraulics...74 Hydraulic Cylinder (810-738C) (Red Lion)...74 Hydraulic Cylinder (810-838C) Red Lion...76 Hydraulic Cylinder Plumbing Components...78 Hydraulic Cylinder Rephase (810-632C) 3X...80 Hydraulic Cylinder Rephase (810-831C) Red Lion 25 X...82 Hydraulic Cylinder Wing Deck (810-362C) Cross...84 Hydraulic Cylinder Wing Deck (810-362C) Midway...86 Hydraulic Cylinders W/ Mounting Components...88 Section 8: Options & Accessories...90 Blade Carrier Components...90 Blade Carrier Options...92 Lights 5 Inch (LED)...94 Shredder Blades...96 Section 9: Decals...98 Decals...98 Touch-up Paints...100...102 Copyright 201 All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Alphabetized Table of Contents A B D G H L Axle Center...30 Axle Wing...32 Blade Carrier Components...90 Blade Carrier Options...92 Decals...98 Deck Center Components...6 Deck Center Drive Components...8 Deck Wing Components...10 Deck Wing Drive Components...12 Divider Box 1000 RPM 35:1 (826-709C)...62 Divider Box 540 RPM 1:35 (826-708C)...64 Driveline Center (826-820C) Comer...46 Driveline Conv. 1000 RPM (826-247C) Walterscheid...48 Driveline Conv. 540 RPM (826-112C) Walterscheid...50 Driveline CV 38 1000 RPM (826-644C) Weasler...52 Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler...54 Driveline CV 75 1000 RPM (826-645C)...56 Driveline CV 540 RPM (826-643C) Weasler...58 Driveline Wing (826-819C) Comer...60 Gearbox (826-840C)...66 Gearbox (826-841C)...68 Gearbox 1000 RPM (826-626C) Comer...70 Gearbox 540 RPM (826-316C)...72 Guards Chain Double Row Front...38 Guards Chain Double Row Rear...40 Guards Chain Single Row Front...42 Guards Chain Single Row Rear...44 Hitch A-Frame...14 Hitch Ball Coupler...16 Hitch Bar Tite...18 Hitch LP Performance...20 Hitch Pintle...22 Hitch Standard Pivoting Clevis...24 Hub Assembly (330-938K)...34 Hydraulic Cylinder (810-738C) (Red Lion)...74 Hydraulic Cylinder (810-838C) Red Lion...76 Hydraulic Cylinder Plumbing Components...78 Hydraulic Cylinder Rephase (810-632C) 3X...80 Hydraulic Cylinder Rephase (810-831C) Red Lion 25 X...82 Hydraulic Cylinder Wing Deck (810-362C) Cross...84 Hydraulic Cylinder Wing Deck (810-362C) Midway...86 Hydraulic Cylinders W/ Mounting Components...88 Touch-up Paints...100 Leveling Rod...26 S T Lights 5 Inch (LED)...28 Lights 5 Inch (LED)...94 Shredder Blades...96 Tire Options...36 07/10/18 RC(M)4620 Rotary Cutter 331-936P 3
4 RC(M)4620 Rotary Cutter 331-936P 07/10/18
07/10/18 RC(M)4620 Rotary Cutter 331-936P 5
Deck Center Components Section 2: Decks & Hitches 39218 6 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Deck Center Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 Dwg 39218 318-920S 330-801H 330-802H 331-903H 331-903H81 331-903H82 331-903H83 331-903H86 331-904H 331-904H81 331-904H82 331-904H83 331-904H86 802-005C 802-091C 802-287C 802-377C 802-456C 803-037C 803-147C 803-168C 803-255C 804-007C 804-017C 804-029C 805-104C 805-131C 807-073C 807-271C 816-481C 840-273C Image No. MANUAL STORAGE CONTAINER KIT SPRING TRUNNION SKID SHOE DECK CENTER W/O DR DECK CENTER W/O DR GREEN DECK CENTER W/O DR ORANGE DECK CENTER W/O DR RED DECK CENTER W/O DR YELLOW DECK CENTER W/ DR DECK CENTER W/ DR GREEN DECK CENTER W/ DR ORANGE DECK CENTER W/ DR RED DECK CENTER W/ DR YELLOW HHCS 1/4-20X1 GR5 HHCS 1/2-13X1 1/2 GR5 HHCS 1-8X9 1/2 GR5 HHCS 1/2-13X7 1/2 GR5 HFS 1/2-13X2 GR8 NUT HEX WHIZ 1/2-13 PLT NUT HEX NYLOCK 1/2-13 NUT HEX TOP LOCK 1-8 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT WASHER FLAT 1/2 USS PLT WASHER FLAT 1 SAE PIN COTTER 3/16 X 1 1/2 PLT PIN CLVS 0X69 USBL SPRING HOSE LOOP HEAVY SPRING COMP 20OD.63W 5.5L MANUAL STORAGE CONTAINER PLUG LP 3" ID RUBBER Beige Green Orange Red Yellow Beige Green Orange Red Yellow 07/10/18 RC(M)4620 Rotary Cutter 331-936P 7
Deck Center Drive Components Section 2: Decks & Hitches 39219 8 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Deck Center Drive Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 17. 1 19. 20. 20. 20. 20. 20. 20. 2 2 2 2 2 Dwg 39219 318-141H 330-661D 330-662D 331-046H 331-356D 802-007C 802-065C 802-314C 802-900C 803-177C 803-209C 804-009C 804-010C 804-036C 807-023C 817-259C 826-316C 826-626C 826-486C 826-820C 826-643C 826-112C 826-793C 826-645C 826-644C 826-247C 826-708C 826-709C 837-066C 837-079C 842-243C Image No. WLDMT. SHAFT PROTECTOR SHIELD, FRONT HALF BRKT, SHIELD MOUNT SHIELD, REAR HALF SHIELD LOCK BRKT HHCS 5/16-18X3/4 GR5 HHCS 3/4-10X2 1/4 GR5 HHCS M8X25X20 GR8 HHCS 3/8-16X8 GR5 ZNYCR NUT HEX FLG TP LK 5/16-18ZNYCR NUT FLANGE LOCK 3/8-16 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER FLAT 5/16 SAE PLT SPRING HOSE LOOP KNOB 3/8-16 FEMALE THD 2 3/8OD GBOX RC50 1:46 REV GBOX RCM50 21:1 REV COMER U0.125.70000 DIPSTICK DRVLN C4 16 75-20 FX CLTCH DRVLN C6 42 38-6 CV DRVLN C5 40 38-6 QD DRVLN C6 39 38-21 CV ORCLTCH DRVLN C6 47 75-20 CV DRVLN C6 42 38-21 CV DRVLN C5 44 38-21 QD DIV BOX 540RPM 1:35 DIV BOX 1000RPM 35:1 DRIVELINE SHIELD CONE, 2 PIECE EA DRVLN SHLD CONE, 2 PIECE LONG HHCS M8X25X20 GR8 THD-LCK Used only with RC4614 540 RPM 1000 RPM 540 RPM 540 RPM 1000 RPM 1000 RPM 1000 RPM 1000 RPM 540 RPM 1000 RPM Used only with driveline 826-793C 07/10/18 RC(M)4620 Rotary Cutter 331-936P 9
Deck Wing Components Section 2: Decks & Hitches 39220 10 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Deck Wing Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. Dwg 39220 330-522D 330-528D 330-526D 330-529D 330-788H 330-982H 330-806L 330-807H 330-835D 331-120H 331-905H 331-905H81 331-905H82 331-905H83 331-905H86 331-906H 331-906H81 331-906H82 331-906H83 331-906H86 331-907H 331-907H81 331-907H82 331-907H83 331-907H86 331-908H 331-908H81 331-908H82 331-908H83 331-908H86 800-001C 802-022C 802-106C 802-155C 802-466C 802-754C 803-030C 803-037C 803-123C 803-198C 804-027C 840-273C Image No. DEFLECTOR INNER RH DEFLECTOR INNER LH DEFLECTOR OUTER RH DEFLECTOR OUTER LH MOUNT REPH CYL ADJ RH MOUNT REPH CYL ADJ LH ASSY HINGE ROD HINGE ROD WING SKID SHOE HARDENED WING SKID SHOE DECK WING RH W/O DR DECK WING RH W/O DR GREEN DECK WING RH W/O DR ORANGE DECK WING RH W/O DR RED DECK WING RH W/O DR YELLOW DECK WING RH W/ DR DECK WING RH W/ DR GREEN DECK WING RH W/ DR ORANGE DECK WING RH W/ DR RED DECK WING RH W/ DR YELLOW DECK WING LH W/O DR DECK WING LH W/O DR GREEN DECK WING LH W/O DR ORANGE DECK WING LH W/O DR RED DECK WING LH W/O DR YELLOW DECK WING LH W/ DR DECK WING LH W/ DR GREEN DECK WING LH W/ DR ORANGE DECK WING LH W/ DR RED DECK WING LH W/ DR YELLOW GREASE ZERK STRAIGHT 1/4-28 HHCS 3/8-16X1 1/2 GR5 RHSNB 1/2-13X1 1/2 GR5 RHSNB 3/8-16X1 1/4 GR5 PLOW 3/8-16X1 1/4 GR5 EYE BOLT 1-8X7 1/2 LG PLT SP NUT HEX JAM 1-8 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX TOP LOCK 3/8-16 PLT NUT HEX WHIZ 3/8-16 PLT WASHER LOCK SPRING 1 PLT PLUG LP 3" ID RUBBER Right wing Left wing Right wing Left wing Right wing Left Wing Beige Green Orange Red Yellow Beige Green Orange Red Yellow Beige Green Orange Red Yellow Beige Green Orange Red Yellow 07/10/18 RC(M)4620 Rotary Cutter 331-936P 11
Deck Wing Drive Components Section 2: Decks & Hitches 39221 12 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Deck Wing Drive Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 7. 9. Dwg 39221 802-065C 803-299C 804-009C 804-010C 826-486C 826-819C 826-840C 826-841C 837-066C 842-243C Image No. HHCS 3/4-10X2 1/4 GR5 NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT COMER U0.125.70000 DIPSTICK DRVLN C5 65 75-20 FX CLTCH GBOX RC50 1:1 STD GBOX RC50 1:1 REV DRIVELINE SHIELD CONE, 2 PIECE HHCS M8X25X20 GR8 THD-LCK Left & Right wing Right wing Left wing 07/10/18 RC(M)4620 Rotary Cutter 331-936P 13
Hitch A-Frame Table of Contents Section 2: Decks & Hitches 39277 14 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 2: Decks & Hitches Hitch A-Frame Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 26. Dwg 39277 331-087D 331-088D 331-089D 331-561H 331-629H 800-001C 802-096C 802-106C 802-143C 802-155C 803-013C 803-014C 803-020C 803-031C 803-168C 804-011C 804-013C 804-015C 804-027C 804-028C 804-029C 805-249C 805-548C 890-182C N\A 891-524C Image No. PTO HANGER BUSHING PTO HANGER STOP PTO HANGER ADJUSTABLE JACK MOUNT HITCH W/ ADJ JACK MNT GREASE ZERK STRAIGHT 1/4-28 HHCS 1-8X2 1/2 GR5 RHSNB 1/2-13X1 1/2 GR5 HHCS 3/8-16X2 GR5 RHSNB 3/8-16X1 1/4 GR5 NUT LOCK 3/8-16 PLT NUT HEX 3/8-16 PLT NUT HEX 1/2-13 PLT NUT HEX 1-8 PLT NUT HEX TOP LOCK 1-8 PLT WASHER FLAT 3/8 USS PLT WASHER LOCK SPRING 3/8 PLT WASHER LOCK SPRING 1/2 PLT WASHER LOCK SPRING 1 PLT WASHER FLAT 1 USS PLT WASHER FLAT 1 SAE PIN ROLL 3/8 X 2 PLT PIN 0 X 62 USBL HRDN SAFETY CHAIN 10000 LB SIDEWIND JACK 7000 LB Available with sidewind jack 07/10/18 RC(M)4620 Rotary Cutter 331-936P 15
Hitch Ball Coupler Table of Contents Section 2: Decks & Hitches 26568 16 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hitch Ball Coupler Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg 26568 330-335A 330-348H 802-053C 803-304C Drawing Image Number 2 5/16" BALL HITCH ASSEMBLY * 2 5/16" BALL HITCH WELDMENT HHCS 5/8-11X1 3/4 GR5 NUT HEX WHIZ 5/8-11 PLT For 2-5/16" Ball 07/10/18 RC(M)4620 Rotary Cutter 331-936P 17
Hitch Bar Tite Table of Contents Section 2: Decks & Hitches 26569 18 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 2: Decks & Hitches Hitch Bar Tite Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 Dwg 26569 330-333A 318-358H 318-834H 330-271H 330-563D 330-564D 330-975H 800-001C 802-053C 802-070C 802-074C 802-205C 803-168C 803-181C 803-258C 803-301C 803-304C 804-025C 804-028C 804-171C 805-105C 890-862C 330-974K Drawing Image Number BAR TITE HITCH * SHAFT WELDMENT WELDMENT HITCH CLEVIS SWIVEL RECEIVER HITCH WEAR PLATE WIDE FORMED HITCH SUPPORT WIDE BAR TITE WIDE TOP GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 3/4-10X6 GR5 HHCS 1-8X6 1/2 GR5 HHCS 1-8X5 1/2 GR5 NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 3/4-10 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER FLAT 50 HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING 50ODX00IDX25 BAR TITE HITCH WIDE 07/10/18 RC(M)4620 Rotary Cutter 331-936P 19
Hitch LP Performance Section 2: Decks & Hitches 39286 20 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hitch LP Performance Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. Dwg 39286 334-045A * 330-271H 331-543D 334-046H 334-048H 800-001C 802-053C 802-075C 802-079C 803-201C 803-258C 803-301C 803-304C 804-013C 804-171C 805-105C 890-836C 890-850C Image No. LP PERFORMANCE HITCH SWIVEL RECEIVER HITCH HOLDER HITCH CLEVIS HITCH YOKE GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X7 GR5 HHCS 3/8-16X1 1/4 GR5 NUT HEX COUPLER 3/8-16X1 3/4 NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 50 HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING 1 1/4X1X1/2 HRD BUSHING 1 1/4X1X5/8 07/10/18 RC(M)4620 Rotary Cutter 331-936P 21
Hitch Pintle Table of Contents Section 2: Decks & Hitches 26570 22 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 2: Decks & Hitches Hitch Pintle Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 Dwg 26570 330-334A 318-006H 318-053L 318-556H 330-223H 802-053C 802-877C 802-729C 803-304C 803-258C 803-304C 804-025C 805-045C 805-083C 890-806C Drawing Image Number PINTLE HITCH * WLDMT. CLEVIS LEVEL ROD ASSY. LEVEL ROD CLEVIS WLDMT. PINTLE HITCH CLEVIS YOKE HITCH HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X9 GR8 SPTHD HFS 5/8-11X2 1/2 GR8 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT WASHER FLAT 3/4 SAE PLT PIN COTTER 5/32 X 1 1/4 LG PIN CLEVIS 3/4 X 1 1/2 PINTLE HOOK SQ.BASE BDB1250-15 07/10/18 RC(M)4620 Rotary Cutter 331-936P 23
Hitch Standard Pivoting Clevis Section 2: Decks & Hitches 26557 24 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hitch Standard Pivoting Clevis Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 Dwg 26557 330-225A 318-005H 318-006H 318-053L 330-223H 802-053C 802-877C 803-304C 803-258C 804-025C 805-045C 805-083C Drawing Image Number STANDARD HITCH * WLDMT. TONGUE CLEVIS WLDMT. CLEVIS LEVEL ROD ASSY. LEVEL ROD CLEVIS YOKE HITCH HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X9 GR8 SPTHD NUT HEX WHIZ 5/8-11 PLT NUT HEX FLG LOCK 1-8 GR B PLT WASHER FLAT 3/4 SAE PLT PIN COTTER 5/32 X 1 1/4 LG PIN CLEVIS 3/4 X 1 1/2 07/10/18 RC(M)4620 Rotary Cutter 331-936P 25
Leveling Rod Table of Contents Section 2: Decks & Hitches 39222 26 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 2: Decks & Hitches Leveling Rod Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. Dwg 39222 318-008H 330-803K 330-804H 803-075C 803-265C 804-025C 805-083C 805-109C Image No. WLDMT. LEVEL ROD SHORT LEVEL ROD ASSY LEVEL ROD LONG NUT HEX JAM 7/8-9 NUT HEX COUPLER 7/8-9X5 WASHER FLAT 3/4 SAE PLT PIN CLVS.75X50 USBL HT PIN COTTER 1/8 X 1 1/4 PLT 07/10/18 RC(M)4620 Rotary Cutter 331-936P 27
Lights 5 Inch (LED) Section 2: Decks & Hitches 37671 28 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Lights 5 Inch (LED) Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 Dwg 37671 334-581A 331-471S 331-472S 330-966D 803-209C 802-015C 891-523C 891-522C 803-255C 804-007C 330-965D 802-224C 803-078C 330-967D 802-318C 802-027C 800-060C 891-529C 891-531C 891-533C J-AC1-15-B J-37-R J-37-A 334-574M Image No. FOLDING CUTTER LGHT KIT 5 LL * RH LIGHT ASSY LH LIGHT ASSY LIGHT GUARD NUT FLANGE LOCK 3/8-16 PLT RHSNB 3/8-16X1 GR5 DUAL LED LIGHT RH DUAL LED LIGHT LH NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT LIGHT MNT HHCS 1/4-20X1 1/4 GR5 NUT LOCK 3/8-16 NYLON INSERT LIGHT MNT CLAMP HHCS 3/8-16X5 GR5 HHCS 3/8-16X4 1/2 GR5 CABLE TIE.19X125 3DIA 50LB LIGHT WIRE HARNESS 8' ENHANCE MODULE LEAD WIRE HARNESS 13' BLACK LENS COVER RED LED LENS MODULE AMBER LED LENS MODULE ROTARY CUTTER LIGHT KIT MANUAL S/N 1150617- Lights were optional Includes Items 3, 4, 5, 6, 8, 9, 10, & 11 Includes Items 3, 4, 5, 7, 8, 9, 10, & 11 Includes items 19, 20, & 21 Includes items 19, 20, & 21 S/N 1058900+ S/N 1058899- Black lens Red lens Amber lens 07/10/18 RC(M)4620 Rotary Cutter 331-936P 29
Axle Center Table of Contents Section 3: Axles 39223 30 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 3: Axles Axle Center Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. Dwg 39223 330-763H 330-938K 331-168H 800-073C 802-099C 803-019C 803-381C 805-058C 815-383C 891-177C Image No. AXLE CENTER HUB 5 BOLT COMPLETE PIVOT PIN TRAILING ARM GREASE ZERK 1/4-28 X 90-DEG HHCS 1/2-13X3 1/4 GR5 NUT LOCK 1/2-13 PLT NUT HEX JAM SLOTTED 1 1/4-7 PIN COTTER 3/16 X 2 DUAL AXLE SPINDLE BHG 50ODX25X38 07/10/18 RC(M)4620 Rotary Cutter 331-936P 31
Axle Wing Table of Contents Section 3: Axles 39224 32 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 3: Axles Axle Wing Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 25. 26. 26. 27. Dwg 39224 330-567D 330-615S 330-616H 330-794H 330-938K 330-969H 331-168H 334-465H 334-467S 334-593H 334-594H 800-001C 800-073C 801-229C 802-082C 802-099C 802-416C 803-019C 803-169C 803-381C 804-016C 804-029C 805-058C 805-104C 807-372C N/A 815-381C 815-387C 891-177C Image No. PIN 1 OD X 5.13 USABLE ASY PIVOT PIN TANDEM ARM PIVOT PIN TANDEM ARM WING AXLE RH HUB 5 BOLT COMPLETE TRAILING ARM WING PIVOT PIN TRAILING ARM WALKING TANDEM PIVOT PIN WALKING TANDEM PIV PIN ASY WING AXLE TRAILING ARM WING GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 X 90-DEG SCREW SLOTTED HEX 1/4-28X3/16 HHCS 1/2-13X1 3/4 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1/2-13X10 GR5 NUT LOCK 1/2-13 PLT NUT HEX FLG LOCK 1/2-13 PLT NUT HEX JAM SLOTTED 1 1/4-7 WASHER FLAT 1/2 SAE PLT WASHER FLAT 1 SAE PIN COTTER 3/16 X 2 PIN COTTER 3/16 X 1 1/2 PLT SPRING COMP 62OD.531W 5L SPRING COMP 5OD.5W 5L DUAL AXLE SPINDLE SINGLE AXLE SPINDLE BHG 50ODX25X38 S/N 1081359- S/N 1081359- S/N - S/N - S/N 1081360+ S/N 1081360+ S/N + S/N + S/N 1081360+ S/N 1081360+ S/N - S/N 1090040+ S/N 1090039- RPBY 807-372C 07/10/18 RC(M)4620 Rotary Cutter 331-936P 33
Hub Assembly (330-938K) Section 3: Axles 37676 34 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hub Assembly (330-938K) Section 3: Axles Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. Dwg 37676 200-001D 330-938K 800-080C 802-779C 803-029C 803-310C 804-055C 805-246C 815-243C 816-497C 822-020C 822-021C 822-033C 822-034C 815-242C Image No. HUB GREASE CAP HUB 5 BOLT COMPLETE GREASE ZERK 1/4-28 THD FORMING HUB STUD 1/2-20X88 GR5 NUT HEX SLOTTED 7/8-14 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT W/CUPS/STUDS SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 HUB 5-BOLT CASTING 07/10/18 RC(M)4620 Rotary Cutter 331-936P 35
Tire Options Table of Contents Section 3: Axles 35672 36 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 3: Axles Tire Options Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 Dwg 35672 814-265C 330-779S 814-449C 330-340D 802-580C 803-019C 804-016C 814-287C 814-450C 814-451C 814-461C Drawing Image Number TIRE & WHL LAM. 6X9X21(5-BOLT) AC TIRE FF 27X7.75X15 5-BOLT TIRE, AC 29" 16 PLY 5 BOLT REINFORCING RING, AC TIRE HHCS 1/2-13X1 1/4 GR8 NUT LOCK 1/2-13 PLT WASHER FLAT 1/2 SAE PLT AC TIRE FF 27X7.75X15 5-BOLT TIRE H29X9.0X15 USED TUBE FOR 29X9.0-15 RIM 2PC 5BLT 15X6.5 07/10/18 RC(M)4620 Rotary Cutter 331-936P 37
Guards Chain Double Row Front Section 4: Guards 39228 38 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Guards Chain Double Row Front Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 Dwg 39228 331-833A * 316-096D 318-107D 318-476D 330-445D 330-446D 330-448D 330-882K 330-884K 330-885K 331-332D 802-015C 803-198C 890-175C 890-341C Image No. CHNGRD FRONT DOUBLE CHAIN HANGER ROD - 32 1/2 LG ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 94 CHNGRD, FRT DBL CNTR CHNGRD, FRT DBL WING CHNGRD FRT DBL CTR OU ASSY CHNGRD WG FRT DBL ASSY CHNGRD CTR FRT DBL ASSY CHNGRD OTR FRT DBL GUARD EXTENSION RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN WELD 5/16 GR 43 X 5 LINK 07/10/18 RC(M)4620 Rotary Cutter 331-936P 39
Guards Chain Double Row Rear Section 4: Guards 39231 40 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Guards Chain Double Row Rear Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. Dwg 39231 330-820A * 312-737D 312-942D 318-478D 330-447D 330-449D 330-886K 330-887K 802-015C 803-198C 890-400C Image No. CHNGRD REAR DOUBLE ROD 1/4 X 44 PLTD. RPBY 318-478D ROUND ROD.25 X 59 CHNGRD, REAR DBL CTR CHNGRD, WING DBL REAR ASSY CHNGRD CTR REAR DBL ASSY CHNGRD WG REAR DBL RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN WELD 5/16 GR 43 X 4 LINK 07/10/18 RC(M)4620 Rotary Cutter 331-936P 41
Guards Chain Single Row Front Section 4: Guards 39225 42 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Guards Chain Single Row Front Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 Dwg 39225 331-812A * 316-096D 318-107D 318-476D 330-428D 330-431D 330-432D 330-810K 330-813K 330-814K 331-332D 802-015C 803-198C 890-175C 890-341C Image No. CHNGRD FRONT SINGLE CHAIN HANGER ROD - 32 1/2 LG ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 94 CHNGRD, FRT SGL WING CHNGRD, FRT SGL CNTR CHNGRD FRT SGL CTR OU ASSY CHNGRD WG FRT SGL ASSY CHNGRD CTR FRT SGL ASSY CHNGRD OTR FRT SGL GUARD EXTENSION RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN WELD 5/16 GR 43 X 5 LINK 07/10/18 RC(M)4620 Rotary Cutter 331-936P 43
Guards Chain Single Row Rear Section 4: Guards 39230 44 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Guards Chain Single Row Rear Section 4: Guards Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. Dwg 39230 330-819A * 312-737D 312-942D 318-478D 330-430D 330-434D 330-812K 330-815K 802-015C 803-198C 890-400C Image No. CHNGRD REAR SINGLE ROD 1/4 X 44 PLTD. RPBY 318-478D ROUND ROD.25 X 59 CHNGRD, WING SGL REAR CHNGRD, REAR SGL CTR ASSY CHNGRD WG REAR SGL ASSY CHNGRD CTR REAR SGL RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN WELD 5/16 GR 43 X 4 LINK 07/10/18 RC(M)4620 Rotary Cutter 331-936P 45
Driveline Center (826-820C) Comer Section 5: Drivelines 37508 46 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline Center (826-820C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. Dwg 37508 826-820C 14026.357.1 180.016.780 190.000.032 190.000.047 170.016.630.1 155.150.726 190.000.016 15016.896.1 146.26021 165.000.589 180.01022 15016.037.1 180.019.019 180.019.340 1501221 180.019.014 180.019.115 180.019.116.1 165.000.548 Image No. PTO E60 X 27.44 1280NM CLUTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE CO INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH COMER LINING RING COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 07/10/18 RC(M)4620 Rotary Cutter 331-936P 47
Driveline Conv. 1000 RPM (826-247C) Walterscheid Section 5: Drivelines Applies to RCM4620 18549 48 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline Conv. 1000 RPM (826-247C) Walterscheid Section 5: Drivelines Applies to RCM4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 Dwg 18549 826-247C 325027 362430 312209 097140 304046 333645 387768 097133 818-540C 365305 087276 044321 391409 818-552C 391410 364915 377437 380371 355155 702352 304011 826-603C 359474 Drawing Image Number PTO 2500 CAT.5 1000 1 3/8-21 * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS YOKE 1 3/8-21 SPL. AS WS CROSS & BEARING KIT 2500 WS INBOARD YOKE 2500 WS SPRING PIN 10 X 90 WS INNER PROFILE S4 WS PROFILE & SLEEVE W.A. WS INBOARD YOKE 2400 DECAL DANGER GUARD MISS PTO WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS OUTER SHIELD TUBE OVAL DECAL DANGER PTO DRIVELINE WS INNER SHIELD TUBE RND. WS ASSY COLLAR KIT WS SHIELD CONE 7 RIB WS ZERK WS SUPPORT BEARING WS HEX BOLT M16 X 90 GR 8 WS LOCK NUT M16 SHIELD KIT, 826-247C WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)4620 Rotary Cutter 331-936P 49
Driveline Conv. 540 RPM (826-112C) Walterscheid Section 5: Drivelines Applies to RC4620 18548 50 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline Conv. 540 RPM (826-112C) Walterscheid Section 5: Drivelines Applies to RC4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 Dwg 18548 826-112C 325027 362428 312209 097140 304046 321256 390257 097133 818-540C 365305 087276 044321 389850 818-552C 388957 339107 377437 380371 355155 702352 304011 377442 826-587C 359474 Drawing Image Number PTO 2500 X 39.76 NO CLUTCH * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS YOKE 1 3/8"-6 SPL. ASG WS CROSS & BEARING KIT 2500 WS INBOARD YOKE 2500 WS SPRING PIN 10 X 90 WS INNER PROFILE 2400 WS PROFILE & SLEEVE W.A. WS INBOARD YOKE 2400 DECAL DANGER GUARD MISS PTO WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS OUTER SHIELD TUBE RND. DECAL DANGER PTO DRIVELINE WS INNER SHIELD TUBE ROUND WS Q.D. PIN KIT WS SHIELD CONE 7 RIB WS ZERK WS SUPPORT BEARING WS HEX BOLT M16 X 90 GR 8 WS LOCK NUT M16 WS SHIELD CONE - 12 RIB SHIELD KIT, 826-112C WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)4620 Rotary Cutter 331-936P 51
Driveline CV 38 1000 RPM (826-644C) Weasler Section 5: Drivelines Applies to RCM4620 37911 52 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline CV 38 1000 RPM (826-644C) Weasler Section 5: Drivelines Applies to RCM4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. Dwg 37911 826-644C 26-15120 68810-1003 03-15570 26-16033 99-24406 19-15135 97-25023 96-24406 98-24406 03-15316 55051-1817 11-14988 11-15180 93-25023 92-24406 91-25023 Drawing Image Number DRVLN C6 42 38-21 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET 07/10/18 RC(M)4620 Rotary Cutter 331-936P 53
Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler Applies to RCM4620 Section 5: Drivelines 35997 54 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler Section 5: Drivelines Applies to RCM4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 Dwg 35997 826-793C 26-15120 68810-1003 03-15570 26-16033 99-24406 97-26654 19-15135 13-10021 13-10022 96-26654 98-26654 03-15316 39-10039 Drawing Image Number DRVLN C6 39 38-21 CV ORCLTCH * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE OUTER GUARD WE GUARD REPAIR KIT WE SAFETY SIGN WE SAFETY SIGN WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE OVERRUNNING THRST CLTCH ASM 07/10/18 RC(M)4620 Rotary Cutter 331-936P 55
Driveline CV 75 1000 RPM (826-645C) Section 5: Drivelines Applies to RCM4620 37912 56 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline CV 75 1000 RPM (826-645C) Section 5: Drivelines Applies to RCM4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. Dwg 37912 826-645C 26-13387 68810-1005 03-15570 26-16033 99-24406 19-15135 97-25075 96-25075 98-25075 03-15316 55051-1817 11-14988 11-15180 93-25075 92-25075 Drawing Image Number DRVLN C6 47 75-20 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD 07/10/18 RC(M)4620 Rotary Cutter 331-936P 57
Driveline CV 540 RPM (826-643C) Weasler Section 5: Drivelines Applies to RC4620 37916 58 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline CV 540 RPM (826-643C) Weasler Section 5: Drivelines Applies to RC4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. Dwg 37916 826-643C 26-15120 68810-1004 03-15570 26-16033 99-24406 19-15135 97-24406 96-24406 98-24406 03-15316 55051-1817 11-14988 11-15180 93-24406 92-24406 91-24406 Drawing Image Number DRVLN C6 42 38-6 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT W/ CHAINS WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET 07/10/18 RC(M)4620 Rotary Cutter 331-936P 59
Driveline Wing (826-819C) Comer Section 5: Drivelines 37507 60 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Driveline Wing (826-819C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 26. 27. 2 29. 30. 3 3 3 3 35. 36. Dwg 37507 826-819C 1402195.1 180.01581 190.000.035 190.000.047 1501241 190.000.243 180.01437 150.285257810 159.280.207 190.000.271 1501241 146.28020.1 180.01251 180.01240 180.01252 180.016.790 14286.2499821 165.000.589 180.01022 1501016.1 180.019.019 180.019.018 1501221 180.019.014 180.019.115 180.019.116.1 165.000.548 14282489821 14287.2179821 12386.1801 12486.3301 190.000.098 190.000.099 180.01393 180.01435 190.000.920 Image No. PTO V80 X 77.05 1280NM CLUTCH * COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE OUTER COMER OUTER TUBE ROLL PIN COMER WIPER CO COMPLETE OUTER TUBE CO INNER TUBE COMER ROLL PIN FOR INNER TUBE COMER INNER YOKE COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE GUARD CO HALF MALE GUARD CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER COMER CAP OUTER TUBE, PLASTIC COMER INNER CAP CO LABEL W/CUSTOMER CODE (S/N 928934-) 07/10/18 RC(M)4620 Rotary Cutter 331-936P 61
Divider Box 1000 RPM 35:1 (826-709C) Section 6: Gearboxes Applies to RCM4620 33807 62 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Divider Box 1000 RPM 35:1 (826-709C) Section 6: Gearboxes Applies to RCM4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 Dwg 33807 826-709C 0.9.00143 0.305.0300.01 7.02348 5.01772 A.709.500 0.305.5006.00 0.305.3000.00 0.305.60000 0.305.2000.00 0.305.1300.00 00109 6.6.00088 6.6.00201 Drawing Image Number DIV BOX 1000RPM 35:1 * CO BRG 30209 TAPPERED CO CASING CO DUST LIP (45X85X10) CO SNAP RING COMER SHIM KIT CO GEAR M6 Z20 CO SHAFT 1" 3/4 Z20 CO GEAR M6 Z27 CO SHAFT 1" 3/4 Z20 TOP COVER PLATE CO BOLT M10 X 35 8 CO 1/2" GAS OIL PLUG W/EMB HEX CO PLUG 3/8 GAS (SOLID PLUG) 07/10/18 RC(M)4620 Rotary Cutter 331-936P 63
Divider Box 540 RPM 1:35 (826-708C) Section 6: Gearboxes Applies to RC4620 33806 64 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Divider Box 540 RPM 1:35 (826-708C) Section 6: Gearboxes Applies to RC4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 Dwg 33806 826-708C 0.9.00143 0.305.0300.01 7.02348 5.01772 A.709.500 0.305.5006.00 0.305.3000.00 0.305.60000 0.305.2000.00 0.305.1300.00 00109 6.6.00088 6.6.00201 Drawing Image Number DIV BOX 540RPM 1:35 * CO BRG 30209 TAPPERED CO CASING CO DUST LIP (45X85X10) CO SNAP RING COMER SHIM KIT CO GEAR M6 Z20 CO SHAFT 1" 3/4 Z20 CO GEAR M6 Z27 CO SHAFT 1" 3/4 Z20 TOP COVER PLATE CO BOLT M10 X 35 8 CO 1/2" GAS OIL PLUG W/EMB HEX CO PLUG 3/8 GAS (SOLID PLUG) 07/10/18 RC(M)4620 Rotary Cutter 331-936P 65
Gearbox (826-840C) Section 6: Gearboxes 39261 66 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Gearbox (826-840C) Section 6: Gearboxes Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 26. 27. Dwg 39261 0.1271000 0.147109.00 0.257525.00 0.285.7510.00 0.2871000 A.709.500 A.71500 1871000 0.9.00079 0.9.00143 0.9.01090 00501 00560 7.02265 5.00533 5.00332 6.5.00006 6.6.02901 7.02349 7.02348 U0.125.05300 U0.125.13000 U0.125.2050.00 U0.125.30000 U0.125.50000 U0.125.7100.00 7.01045 Image No. CO CAP CO NAME PLATE CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO BLANK WASHER COMER SHIM KIT COMER SHIM KIT CO SEAL PROTECTOR CO BRG 30212 (60X110X275) CO BRG 30209 TAPERED CO BRG 32210 (50X90X275) CO BOLT M10X22 HHB CO CASTLE NUT M36X3 CO COTTER PIN B 5X60 CO SNAP RING 50 UNI7435 CO SNAP RING UNI 7437 CO OIL PLUG 3/8 CO GAS PLUG 1/2 CO OIL SEAL 60X110X12 SL CO DUST LIP (45X85X10) CO CASTING & MACHINING CO TOP COVER CO INPUT SHAFT 1 3/4"-20 CO OUTPUT SHAFT GEAR CROWN Z21 M7.75 CO CASTLE NUT CO COTTER PIN B6X70 SLD-SPRTLY 07/10/18 RC(M)4620 Rotary Cutter 331-936P 67
Gearbox (826-841C) Section 6: Gearboxes 39262 68 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Gearbox (826-841C) Section 6: Gearboxes Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 26. 27. Dwg 39262 826-841C 0.1271000 0.147109.00 0.257525.00 0.285.7510.00 0.2871000 A.709.500 A.71500 1871000 0.9.00079 0.9.00143 0.9.01090 00501 00560 7.02265 5.00533 5.00332 6.5.00006 6.6.02901 7.02349 7.02348 U0.125.05300 U0.125.13000 U0.125.2050.00 U0.125.30000 U0.125.50000 U0.125.7100.00 7.01045 Image No. GBOX RC50 1:1 REV * CO CAP CO NAME PLATE CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO BLANK WASHER COMER SHIM KIT COMER SHIM KIT CO SEAL PROTECTOR CO BRG 30212 (60X110X275) CO BRG 30209 TAPERED CO BRG 32210 (50X90X275) CO BOLT M10X22 HHB CO CASTLE NUT M36X3 CO COTTER PIN B 5X60 CO SNAP RING 50 UNI7435 CO SNAP RING UNI 7437 CO OIL PLUG 3/8 CO GAS PLUG 1/2 CO OIL SEAL 60X110X12 SL CO DUST LIP (45X85X10) CO CASTING & MACHINING CO TOP COVER CO INPUT SHAFT 1 3/4"-20 CO OUTPUT SHAFT GEAR CROWN Z21 M7.75 CO CASTLE NUT CO COTTER PIN B6X70 SLD-SPRTLY 07/10/18 RC(M)4620 Rotary Cutter 331-936P 69
Gearbox 1000 RPM (826-626C) Comer Applies to RCM4620 Section 6: Gearboxes 26639 70 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Gearbox 1000 RPM (826-626C) Comer Section 6: Gearboxes Applies to RCM4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 26. 27. Dwg 21167 826-626C U0.125.05300 U0.125.60000 0.9.00143 7.00331 U0.125.2050.00 5.00332 0.709.7500.00 5.00533 U0.125.7100.00 0.717500.00 0.9.01090 1871000 7.02349 0.9.00079 U0.125.30000 7.02265 0.1271000 0.2871000 0.257525.00 0.285.7510.00 U0.125.13000 00501 826-486C 6.5.00006 7.01045 00560 U0.125.50000 Drawing Image Number GBOX RCM50 75-20 21:1 CCW * CO HOUSING CO CROWN GEAR Z18 M7.8 CO BEARING 30209 RTA25 CO OIL SEAL 45 X 85 X 10 CO INPUT SHAFT 1 3/4"-20 CO SNAP RING UNI 7437 CO SHIM 87 CO SNAP RING 50 UNI7435 CO CASTLE NUT CO SHIM 50.3X70.3 CO BEARING 32210 CO SEAL PROTECTOR CO OIL SEAL 60X110X12 CO BEARING 30212 CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO COVER CO BOLT M10X22 HHB COMER U0.125.70000 OIL PLUG CO OIL PLUG 3/8 CO COTTER PIN B6X70 SLD-SPRTLY CO CASTLE NUT M36X3 CO CROWN GEAR Z22 M7.8 07/10/18 RC(M)4620 Rotary Cutter 331-936P 71
Gearbox 540 RPM (826-316C) Applies to RC4620 Section 6: Gearboxes 21171 72 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Gearbox 540 RPM (826-316C) Section 6: Gearboxes Applies to RC4620 Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 2 2 25. 26. 27. Dwg 21771 826-316C U0.125.05300 U0.125.5005.00 0.9.00143 7.00331 U0.125.2050.00 5.00332 0.709.7500.00 5.00533 U0.125.7100.00 0.717500.00 0.9.01090 1871000 7.02349 0.9.00079 U0.125.30000 7.02265 0.1271000 0.2871000 0.257525.00 0.285.7510.00 U0.125.13000 00501 826-486C 6.5.00006 7.01045 00560 U0.125.60000 Drawing Image Number GBOX RC50 75-20 1:46 CW * CO HOUSING CO CROWN GEAR Z22 M8 CO BEARING 30209 RTA25 CO OIL SEAL 45 X 85 X 10 CO INPUT SHAFT 1 3/4"-20 CO SNAP RING UNI 7437 CO SHIM 87 CO SNAP RING 50 UNI7435 CO CASTLE NUT CO SHIM 50.3X70.3 CO BEARING 32210 CO SEAL PROTECTOR CO OIL SEAL 60X110X12 CO BEARING 30212 CO OUTPUT SHAFT CO COTTER PIN B 5X60 CO CAP CO BLANK WASHER CO SHIM 45.3X5 CO SHIM 40.3 X 67 X 1 CO COVER CO BOLT M10X22 HHB COMER U0.125.70000 OIL PLUG CO OIL PLUG 3/8 CO COTTER PIN B6X70 SLD-SPRTLY CO CASTLE NUT M36X3 CO CROWN GEAR Z15 M8 * Notes: Oil Type 80-90W Capacity 10 Pints R. H. Deck 07/10/18 RC(M)4620 Rotary Cutter 331-936P 73
Hydraulic Cylinder (810-738C) (Red Lion) Section 7: Hydraulics 33905 74 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder (810-738C) (Red Lion) Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. Dwg 33905 810-738C 492660 492661 294727 492180 464264 492278 235005 N/A N/A N/A N/A N/A N/A 492650 803-020C 130556 186562 N/A 851-348C Drawing Image Number CYL REP 75X8X13 ROD (TIE) * MON CLEVIS CAP 75-3/4ORB-0 MON ROD CAP 75-12-3/4ORB MON PISTON 75-.75-TH-TP-TD MON ROD CYL12-08-.75-12-TP MON TUBE WELDT 75-000-TP MON TIE ROD MON PIN KIT 00C/W COTTER PIN MON SEAL HALLITE 605 ROD 13 MON ORING 141 2 5/16X2 1/2 LION WIPER SEAL MON SEAL PTFE PSTN RING 2 3/4D MON WEAR RNG 75-50-.25-GFN MON NYLON THREAD PROTECTOR LION ROD CLEVIS 1 1/8-12UNF NUT HEX 1/2-13 PLT MON PISTON NUT LION PLUG 3/4-16UNF SOCKET HD MON SEAL DUAL 75 MON SEAL KIT 810-738C 07/10/18 RC(M)4620 Rotary Cutter 331-936P 75
Hydraulic Cylinder (810-838C) Red Lion Section 7: Hydraulics 35033 76 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder (810-838C) Red Lion Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 Dwg 35033 810-838C 803-020C 130560 148000 258821 491742 492282 492652 492721 492870 494383 649206 Drawing Image Number CYL 3X12X25 ROD (TIE ROD) * NUT HEX 1/2-13 PLT MON PISTON NUT MON SET SCREW 3/8INC ONE PIECE MON PISTON 00-0-TSS-ISO-WR MON CYL TUBE MON TIE ROD LION ROD CLEVIS 1 1/4 (1PIN) LION CLEVIS CAP 0-9/16 ORB MON CYL ROD MON ROD CAP00-25-9/16ORBTS MON SEAL KIT KR30WR-125 TSS 07/10/18 RC(M)4620 Rotary Cutter 331-936P 77
Hydraulic Cylinder Plumbing Components Section 7: Hydraulics 33805 78 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder Plumbing Components Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 10. 1 1 1 1 15. Dwg 33805 810-831C 810-632C 810-738C 811-088C 811-394C 841-654C 811-142C 841-605C 841-606C 810-362C 810-838C 811-337C 811-309C 811-356C 811-238C 800-117C Drawing Image Number CYL REP 25X8X25 ROD (TIE) REP CYL 3X8X25 ROD (TIE) CYL REP 75X8X13 ROD (TIE) AD 3/4MORB 3/4MJIC CP 3/4FORB MALE QD POPPET TYPE HH3/8R1 228 3/4MORB 3/4FJIC HH3/8R1 114 3/4FJIC HH3/8R1 234 3/4FJIC HH3/8R1 288 3/4MORB 3/4FJIC CYL 5X12X25ROD (TIE ROD) CYL 3X12X25 ROD (TIE ROD) OREL 1/16 9/16MJIC 9/16MORB HH1/4R1 066 9/16FJIC TE 9/16MJIC BH 9/16MJIC 9/16MJ HH3/8R1 189 9/16FJIC 3/4MORB VENT PLUG - 9/16-18 PLATED S/N 1058900+ must grind 1/4" out of the radius of the lug that the base end of the cylinder attaches to if your machine is under S/N 1058900 S/N 1058899-07/10/18 RC(M)4620 Rotary Cutter 331-936P 79
Hydraulic Cylinder Rephase (810-632C) 3X8 Section 7: Hydraulics 27884 80 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder Rephase (810-632C) 3X8 Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. 20. 2 Dwg 27884 810-632C 803-020C 130560 134953 135995 801-023C 186562 N/A N/A N/A N/A 292675 294719 464265 492278 492652 492670 492700 N/A N/A N/A 639558 Drawing Image Number REP CYL 3X8X25 ROD (TIE) * NUT HEX 1/2-13 PLT MON PISTON NUT LION PIN MON CLEVIS PIN COTTER SCREW SET SH 3/8-16X3/8 TYPE C LION PLUG 3/4-16UNF SOCKET HD MON ROD SEAL MON END CAP B/U WASHER MON END CAP O-RING SEAL WIPER ROD MON CLEVIS CAP MON PISTON MON TUBE MON TIE ROD LION ROD CLEVIS 1 1/4 (1PIN) MON ROD CAP LION ROD 25 DIA. ASAE 8 O-RING EXPANDER WEAR RING MON REPAIR KIT Only in Seal Kit Item 21 Only in Seal Kit Item 21 Only in Seal Kit Item 21 Only in Seal Kit Item 21 Only in Seal Kit Item 21 Only in Seal Kit Item 21 Only in Seal Kit Item 21 07/10/18 RC(M)4620 Rotary Cutter 331-936P 81
Hydraulic Cylinder Rephase (810-831C) Red Lion 25 X 8 Section 7: Hydraulics 33230 82 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder Rephase (810-831C) Red Lion 25 X 8 Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 19. Dwg 33230 810-831C 803-022C 130560 148000 186562 N/A N/A N/A N/A N/A N/A 294737 464266 492338 492652 492662 492664 492700 235005 639560 Drawing Image Number CYL REP 25X8X25 ROD (TIE) * NUT HEX 5/8-18 PLT MON PISTON NUT MON SET SCREW 3/8INC ONE PIECE LION PLUG 3/4-16UNF SOCKET HD MON SEAL PTFE PISTN RING 3-1/4 MON SEAL HALLITE 605 ROD 1-1/4 MON O RING 149 2-13/16X3 DUR90 MON SEAL WIPER ROD 250 METAL MON SEAL DUAL 25 MON WEAR RNG 25-00-.25-GFN MON PISTON 25-00-TP MON TUBE WELDT 25-000-TP LION TIE ROD 5/8 X 8 LION ROD CLEVIS 1 1/4 (1PIN) MON CLEVIS CAP 25-3/4ORB-0 MON ROD CAP 25-25-3/4ORB LION ROD 25 DIA. ASAE 8 MON PIN KIT 00C/W COTTER PIN MON SEAL KIT 32TP08-125 Order Seal Kit Item #19 Order Seal Kit Item #19 Order Seal Kit Item #19 Order Seal Kit Item #19 Order Seal Kit Item #19 Order Seal Kit Item #19 07/10/18 RC(M)4620 Rotary Cutter 331-936P 83
Hydraulic Cylinder Wing Deck (810-362C) Cross Section 7: Hydraulics 15704 84 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder Wing Deck (810-362C) Cross Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 Dwg 15704 810-362C 1D0009-1450 1D0205-1662 1D1013-5 2A0235-6 2A0079-616 2A0581-1725 2A0236-9 1D1159-7 N/A N/A N/A N/A 1D1401-350 1D1224-7 1A1141 1D1551-16300 2A0308-1 810-146C Drawing Image Number CYL 5x12x25ROD (TIE ROD) * CROSS TUBE CROSS ROD CROSS ROD CLEVIS CROSS NUT, CLEVIS & TIE ROD CROSS SCREW, CAP CROSS TIE ROD TIE ROD NUT CROSS HEAD CROSS BACKUP PISTON U-CUP ROD WIPER O-RING PISTON PISTON CROSS BASE CROSS 826-362C PISTON NUT CROSS CROSS CLEVIS PIN CROSS PIN, CLIP SEAL KIT CROSS 5 CYL 1C4429 Only found in seal kit 18 Only found in seal kit 18 Only found in seal kit 18 Only found in seal kit 18 07/10/18 RC(M)4620 Rotary Cutter 331-936P 85
Hydraulic Cylinder Wing Deck (810-362C) Midway Section 7: Hydraulics 15704 86 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinder Wing Deck (810-362C) Midway Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 16. 17. 1 Dwg 15704 810-362C 5M5120 2M5418 1M6010 2A0012 2A0006 7M5320 2A0016 3M5410 N/A N/A N/A N/A 4M5102 6M5152 2A0024 2A0208 2A0132 810-149C Drawing Image Number CYL 5x12x25ROD (TIE ROD) MW TUBE MW ROD 1 1/4 DIA X 10' STROKE MW CLEVIS STD. DUTY MW NUT CLEVIS & TIE ROD MW CAPSCREW TIE ROD MIDWAY MW TIE ROD NUT MW HEAD 3-1/2X1-1/4ROD 9/16SAE MW BACK UP TUBE MW WIPER MW U-CUP MW O-RING MW PISTON 3 1/2 DIA. MW BASE 3 1/2 MW PISTON NUT 1-14 MW CLEVIS PIN MW PIN CLIP SEAL KIT 810-104C MW 3A5102 Found in Seal Kit #18 Found in Seal Kit #18 Found in Seal Kit #18 Found in Seal Kit #18 07/10/18 RC(M)4620 Rotary Cutter 331-936P 87
Hydraulic Cylinders W/ Mounting Components Section 7: Hydraulics 33804 88 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Hydraulic Cylinders W/ Mounting Components Section 7: Hydraulics Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 15. 15. 16. 17. 1 19. Dwg 33804 318-018H 330-567D 330-788H 330-876S 330-982H 802-106C 802-754C 803-030C 803-037C 804-027C 804-029C 805-088C 805-104C 805-131C 810-362C 810-838C 810-632C 810-738C 810-818C 810-831C Drawing Image Number WLDMT. CYLINDER PIN PIN 1 OD X 5.13 USABLE MOUNT REPH CYL ADJ RH TRANSPORT BAR W/ DECALS MOUNT REPH CYL ADJ LH RHSNB 1/2-13X1 1/2 GR5 EYE BOLT 1-8X6 1/2 LG PLT SP NUT HEX JAM 1-8 PLT NUT HEX WHIZ 1/2-13 PLT WASHER LOCK SPRING 1 PLT WASHER FLAT 1 SAE PIN, HAIR COTTER 3/16 WIRE DIA PIN COTTER 3/16 X 1 1/2 PLT PIN CLEVIS 1 X 4 11/16 USABLE CYL 5X12X25ROD (TIE ROD) CYL 3X12X25 ROD (TIE ROD) REP CYL 3X8X25 ROD (TIE) CYL REP 75X8X13 ROD (TIE) STRK CNTRL SPCRS 125 TO 50 CYL REP 25X8X25 ROD (TIE) S/N 1058900+ must grind 1/4" out of the radius of the lug that the base end of the cylinder attaches to if your machine is under S/N 1058900 S/N 1058899-07/10/18 RC(M)4620 Rotary Cutter 331-936P 89
Blade Carrier Components Section 8: Options & Accessories 39217 90 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Blade Carrier Components Section 8: Options & Accessories Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. Dwg 39217 318-871H 330-482D 802-096C 802-277C 803-168C 803-170C 804-147C 820-249C 820-168C 318-586A Image No. BLD PLT DSHPN WMT 31C/C DISHPAN 31" CENTER HHCS 1-8X2 1/2 GR5 BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1-8 PLT NUT HEX TOP LOCK 1 1/8-12 PLT WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X29 CW CUTTER BLADE 1/2X4X29 CCW BLADE BOLT KIT Center deck & Right hand deck Left hand deck 07/10/18 RC(M)4620 Rotary Cutter 331-936P 91
Blade Carrier Options Section 8: Options & Accessories 39264 92 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Blade Carrier Options Section 8: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg 39264 331-930A 331-929A Image No. 20' DIAMOND BLADE BAR W/PANS 20' DIAMOND BLADE BAR 07/10/18 RC(M)4620 Rotary Cutter 331-936P 93
Lights 5 Inch (LED) Section 8: Options & Accessories 37671 94 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Lights 5 Inch (LED) Section 8: Options & Accessories Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 1 15. 16. 17. 1 19. 20. 2 2 Dwg 37671 334-581A 331-471S 331-472S 330-966D 803-209C 802-015C 891-523C 891-522C 803-255C 804-007C 330-965D 802-224C 803-078C 330-967D 802-318C 802-027C 800-060C 891-529C 891-531C 891-533C J-AC1-15-B J-37-R J-37-A 334-574M Image No. FOLDING CUTTER LGHT KIT 5 LL * RH LIGHT ASSY LH LIGHT ASSY LIGHT GUARD NUT FLANGE LOCK 3/8-16 PLT RHSNB 3/8-16X1 GR5 DUAL LED LIGHT RH DUAL LED LIGHT LH NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT LIGHT MNT HHCS 1/4-20X1 1/4 GR5 NUT LOCK 3/8-16 NYLON INSERT LIGHT MNT CLAMP HHCS 3/8-16X5 GR5 HHCS 3/8-16X4 1/2 GR5 CABLE TIE.19X125 3DIA 50LB LIGHT WIRE HARNESS 8' ENHANCE MODULE LEAD WIRE HARNESS 13' BLACK LENS COVER RED LED LENS MODULE AMBER LED LENS MODULE ROTARY CUTTER LIGHT KIT MANUAL S/N 1150617- Lights were optional Includes Items 3, 4, 5, 6, 8, 9, 10, & 11 Includes Items 3, 4, 5, 7, 8, 9, 10, & 11 Includes items 19, 20, & 21 Includes items 19, 20, & 21 S/N 1058900+ S/N 1058899- Black lens Red lens Amber lens 07/10/18 RC(M)4620 Rotary Cutter 331-936P 95
Shredder Blades Table of Contents Section 8: Options & Accessories 39233 96 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Shredder Blades Section 8: Options & Accessories Ref. Part No. Part Description Comments Revision 5. 5. 6. Dwg 39233 318-309D 330-227H 802-680C 803-168C 820-169C 820-170C 820-217C Image No. BLADE BUSHING BLD BAR WMT 45C/C FLAT HHCS 1-8X4 1/2 PLT GR8 NUT HEX TOP LOCK 1-8 PLT CUTTER BLADE 1/2X4X23 CCW CUTTER BLADE 1/2X4X23 CW CUTTER BLADE 1/2X4X25 FLAT Left hand deck Center deck & Right hand deck 07/10/18 RC(M)4620 Rotary Cutter 331-936P 97
Decals Table of Contents Section 9: Decals 39234 98 RC(M)4620 Rotary Cutter 331-936P 07/10/18
Section 9: Decals Decals Table of Contents Ref. Part No. Part Description Comments Revision 5. 6. 7. 9. 10. 1 1 1 1 1 15. 16. 17. 1 19. 20. 20. 2 2 2 2 2 2 2 25. 26. Dwg 39234 818-045C 818-130C 818-240C 818-142C 818-190C 818-229C 818-230C 818-276C 818-543C 818-552C 818-556C 818-561C 818-555C 818-564C 818-714C 818-830C 818-840C 838-094C 838-588C 838-614C 838-615C 838-959C 848-122C 838-965C 848-797C 848-872C 858-325C 858-327C 858-326C 858-328C 858-381C 858-441C Image No. DECAL WARNING PINCH PT/CRUSH DECAL CAUTION 540 RPM DECAL CAUTION 1000 RPM DECAL DANGER PTO DRIVELINE EN DECAL FLAG DECAL AMBER REFLECTOR DECAL RED REFLECTOR DECAL WARNING OPERATING ANGLE DECAL DANGER PD GUARD MISS SML DECAL DANGER PTO DRIVELINE DECAL DANGER THROWN OBJ CUTTER DECAL DANGER RAISED WING HAZAR DECAL DANGER ROTATE BLADE RPBY 818-555C DECAL DANGER CRUSHING TWO IMP DECAL SAFETY COMBO SUNWEST DECAL DANGER ROLLOVER HAZARD DECAL WARNING HYD PRESS LONG FOLDING CUTTER SPEED WARNING DECAL REFLECTOR RED 2X9 DECAL REFLECTOR AMBER 2X9 DECAL LANDPRIDE 30" GREEN DECAL LANDPRIDE 34" TAN/BROWN DECAL LANDPRIDE 16" BROWN/GOLD DECAL BLADE ROTATION DECAL 7 YEAR GEARBOX WARRANTY DECAL RC4620 GREEN DECAL RC4620 GOLD DECAL RCM4620 GREEN DECAL RCM4620 GOLD DECAL JACK ADJUSTMENT DECAL, WRANGLER 540 RPM 1000 RPM Obsolete Beige & Yellow units Green, Orange & Red units Beige & Yellow units Green, Orange & Red units Beige & Yellow units Green, Orange & Red units 07/10/18 RC(M)4620 Rotary Cutter 331-936P 99