Working etween the hook and the load 2015 Product Catalogue for UK & ROW Safe Lifting Solutions
Contents Modulift Sets 03 Modulift Spreader Beams 04 One Beam Many Lifts 05 The Standard Range 06 The Heavy Range 07 Regs, Standards & Compliance 08 Enhanced QA/Custom Design 09 Accessories 10 Design Engineering & Lift Management 12 QuickJoint 2 15 Mod 6 16 Mod 12 17 Mod 24 18 Mod 34 19 Mod 50 20 MOD 50/24 Step-Downs 21 MOD 50/12 Step-Downs 22 MOD 50/6 Step-Downs 23 Mod 70 24 Mod 70H 25 MOD 70/34 Step-Downs 26 MOD 70/24 Step-Downs 27 Mod 110 28 Mod 110H 29 Mod 110SH 30 MOD 110/70 Step-Downs 31 MOD 110/50 Step-Downs 32 Professional Bodies & Regulatory Standards 27 Mod Mod 250/250 600XA/400 33 28 Mod MOD 250/300 600XA/500 34 29 Mod MOD 250/400 600XA/600 35 30 MOD MOD 250/110H 600XA/800 Hyrid 36 31 MOD MOD 250/110 600XB/500 Hyrid 37 32 MOD MOD 250/70H 600XB/800 Hyrid 38 33 MOD MOD 250/70 600 Hyrid B/1000 39 34 Mod 400/400 40 Mod 400/500 41 Mod 400/600 42 MOD 400/250 Hyrid 43 MOD 400/110SH Hyrid 44 MOD 400/110H Hyrid 45 MOD 400/110 Hyrid 46 MOD 600XB/400 47 MOD 600 XB/600 48 MOD 600 XB/800 49 MOD 600 XB/1000 50 MOD 800J/1000 51 CMOD Spreader Frame Range 52 CMOD 6 53 CMOD 12 54 CMOD 24 55 CMOD 34 56 CMOD 50 57 CMOD 70 58 CMOD & Beyond 59 Lattice Spreader Beams 60 Modulift UK Ltd 11 New Fields Business Park Stinsford Road, Poole Dorset BH17 0NF Tel: +44 (0) 1202 621511 Fax: +44 (0) 1202 632811 Email: info@modulift.com We: Lattice SF 6-24m 61 Lattice SF 27m 62 Lattice SF 30m 63 Lattice SF 33m 64 Lattice SF 36m 65 Lattice SF 42m 66 Where To Buy & Contacts 67 2
Modulift Sets The most cost efficient way to purchase the Modulift System is in the predetermined sets. This will allow you to interchange components in each set to gain the full range of spans availale. This tale shows the asic product range and gives you a quick guide to their specification and retail price. The remainder of this catalogue will look at the full range of products and support services in more detail. If the information you need is not within these pages then pick up the phone or send us an email we will e pleased to help you. Standard Heavy QJ2 Up to 2t at 1.2m/4ft MOD 34 Up to 34t at 5m/17ft Up to 8m/26ft at a lower capacity. MOD 110 Up to 110 t at 11m/37ft Up to 16m/52ft at a lower capacity. MOD 250/300 Up to 300t at 12m/40ft Up to 20m/66ft at a lower capacity. MOD 400/600 Up to 600t at 12m/40ft Up to 23m/76ft at a lower capacity. MOD 6 Up to 6t at 2.5m/8ft MOD 50 Up to 50t at 7.5m/25ft Up to 11m/36 ft at a lower capacity. MOD 110H Up to 170t at 8m/26ft Up to 16m/52ft at a lower capacity. MOD 250/400 Up to 400t at 8m/28ft Up to 20m/66ft at a lower capacity. MOD 600/600 Up to 600t at 21m/70ft Up to 26m/85ft at a lower capacity. MOD 12 Up to 12t at 4m/13ft MOD 70 Up to 70t at 9m/29ft Up to 12m/40 ft at a lower capacity. MOD 110SH Up to 240t at 6m/20ft Up to 16m/52ft at a lower capacity. MOD 400/400 Up to 400t at 16m/55ft Up to 23m/76ft at a lower capacity. MOD 600/800 Up to 800t at 18m/60ft Up to 26m/85ft at a lower capacity. MOD 24 Up to 24t at 4.5m/14ft Up to 6m/20ft at a lower capacity. MOD 70H Up to 100t at 8m/25ft Up to 12m/40ft at a lower capacity. MOD 250/250 Up to 250t at 13m/45ft Up to 20m/66ft at a lower capacity. MOD 400/500 Up to 500t at 14m/47ft Up to 23m/76ft at a lower capacity. MOD 600/1000 Up to 1000t at 15m/51ft and up to 26m/85ft at a lower capacity. 3
Modulift Spreader Beams Modulift offer a wide range of Modular Spreader Beam components, offering a variety of different spans for all your lifting needs. Part of the Modulift Standard Range The sizes range from 2 to 5,000t with spans availale from 0.4m/1 4-100m/300 The flexiility of the modular configuration enales our Spreader Beams to e reused time and time again, providing a cost-effective solution. What Size Beam Do I Need? Simple! First select the span you require, then select the you need for that span. Please see tales on pages 6 & 7 to select your eam. Range Classification Part of the Modulift Heavy Range Range Standard Modulift Sizes 6, 12, 24, 34, 50, 70, 70H MOD 600 Heavy 110, 110H, 110SH, 250, 400, 600 MOD 400 MOD 250 MOD 110SH MOD 110/110H 4
One Beam Many Lifts Interchangeale Components For Larger Lighter Loads For longer spans and lighter loads, additional components are availale allowing you to optimise the weight of our higher capacity range of Modular Spreader Beams to carry out these lifts. These struts provide the ackone of our Spreader Beams when trying to achieve longer spans. We have two solutions that can make the system more flexile and cheaper for you y interchanging smaller capacity End Units and Drop Links. Step-Down End Units are designed for smaller sizes, up to the MOD 70 Cone Adaptors accommodate the larger sizes These additional components allow your existing Spreader Beam to ecome even more versatile over a numer of lifts so you can remain cost-effective with your rigging and crane capacity requirements. By stepping down the End Units to a more suitale capacity, you can optimise your Shackles and Slings to provide a lighter system overall. There are a numer of ways you can utilise our Modular Spreader Beams, for example; Need a span of 20m/66 ut are only lifting 70t - we can provide you with a MOD 250/70 giving you Cone Adapters and MOD 70 End Units to olt to MOD 250 struts to achieve the required overall Spreader Beam system. Need to lift 24t ut at 12m/40 - change our standard MOD 70 Spreader Beam End Units to Step-Down End Units and decrease the to 24t allowing you to use smaller Shackles and Slings with the MOD 70 struts. Need to lift 100t if you already have a MOD 70 Spreader Beam, y changing the End Units to the MOD 70H End Units you can increase the to 100t negating the need to uy a completely rand new Spreader Beam. Using one of our Modular Spreader Beams enales you to e more flexile over a numer of lifts without needing to uy a new Spreader Beam every time, our lightweight design also minimises the overall weight of the lifting equipment and the costs incurred whilst working etween the hook and the load. 5
The Standard Range Load v Chart - Modulift Spreader Beam Standard Range 100 95 90 MOD 70H 85 80 75 70 /tonnes @ 60º /60º /30º 65 60 55 50 45 40 35 30 MOD 70 MOD 50 MOD 34 MOD 24 25 20 MOD 24 15 10 MOD 12 5 MOD 6 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 (m) MOD 34 MOD 50 TOP: 25t LOWER: 17t Components per Set * Please note: Custom length Struts are availale on request strut spreader system 0.1m 0.2m 0.25m 0.3m 0.5m 0.6m 0.75m 1.0m 1.5m 2.0m 3.0m 4.0m 6.0m end unit drop link MOD 6 1 1 1 1 1 2 2 MOD 12 1 1 1 1 1 2 2 MOD 24 1 1 2 2 2 MOD 34 1 1 3 2 2 MOD 50 1 1 1 2 2 2 MOD 70/70H 1 1 1 2 2 2 MOD 110/110H/110SH 1 1 1 3 2 2 MOD 250-250/250-300/250-400 1 1 1 2 2 2 MOD 400-400/400-500/400-600 1 1 1 3 2 2 MOD 600-600/600-800/600-1000 1 1 1 3 2 2 6
The Heavy Range Load v Chart - Modulift Spreader Beam Heavy Range onnes @ 60 / 60 / 30 1000 975 950 925 900 875 850 825 800 775 750 725 700 675 650 625 600 575 550 525 500 475 450 425 400 375 350 325 300 275 250 225 200 175 150 125 100 75 50 25 0 MOD 600/1000 MOD 600/800 MOD 400/600 MOD 600/600 MOD 400/500 MOD 250/400 MOD 400/400 MOD 250/300 MOD 110SH MOD 250/250 MOD 110H MOD 110 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 (m) TOP/LOWER: Consult Modulift for Shackle sizes Weight per Set (kgs) * Weight ased on heaviest spreader in series using configuration recommended in user instructions WEIGHT MOD 6 MOD 12 MOD 24 MOD 34 MOD 50 MOD 70/70H MOD 110/110H MOD 110SH Max Component Weight 8.1 19 41 51 140 240 367 444 860 1365 2665 Min Component Weight 0.6 1.3 5 7 11 17/32 44/55 63 90 135 135 Weight at Max 32 75 178 290 532 972/1090 1970/2130 2628 4895 8260 17260 MOD 250 MOD 400 MOD 600 7
Regulations, Standards & Compliance Each Modulift Spreader Beam series has een proven y eing Proof Load Tested in the Modulift compression test rig and all products comply with the relevant standards as detailed elow: UK & Europe Compliance All our Spreader Beams have een designed in accordance with: BS EN 13155: 2003+A2:2009: Cranes Safety Non- fixed load lifting attachments DNV Standard for Certification No. 2.22 Lifting Appliances 2011 Mod 6 up to Mod 800/1000 Type Approved y DNV LOLER: 1998 (Lifting Operations and Lifting Equipment Regulations) PUWER: 1998 (Provision and Use of Work Equipment Regulations) EC Machinery Directive 2006/42/EC BS EN 1993-1: 2005: Eurocode 3 USA Compliance ASME B30.20-20103 For Below-the-Hook Lifting Devices. ASME BTH-1 2011: Design of Below-the-Hook Lifting Devices. Australia Compliance AS 4991-2004: Lifting Devices. DNV Standard for Certification DNV 2.22: Modulift Spreader Beams designs conform to DNV Standard for Certification No.2.22 Lifting Appliances. Modulift is the first and only Spreader Beam Manufacturer in the world to have the gloally recognised DNV Type Approval for all Spreader Beams up to 1000t capacity in accordance with DNV s standard for Certification No. 2.22 for Lifting Appliances 2011, at no extra cost to the client. For those customers who require a higher level of quality standard, Modulift also provides further options for project specific 3rd party verification. When a project demands the highest level of certification Modulift are ale to offer our customers varying degrees of additional DNV certification depending upon their individual QA requirements, including: Proof Load Test Survey Report and Record of Test DNV Certificate of Conformity for Manufacture & Test (CG3 in accordance with ILO convention 152) Please ask aout these additional services at the time of your enquiry. Ask Modulift aout the Level of Options Availale to Ensure Your Safe Lift We now have all our Spreader Beams up to 1000t capacity DNV Type Approved. Level 1. Standard Modulift Spreader Beams In accordance with BS EN 13155-2003. Availale CE Marked and supplied with a Certificate of Conformity, up to 400t availale off-the-shelf. Level 2. Individual Proof Load Testing of Modulift Spreader Beams Modulift offer an individual Proof Load Test service with or without 3rd party verification to those requiring a higher level of certification. Please ask for further information. Level 3. Modulift Spreader Beams with project specific DNV Certification Although our range Spreader Beams are now DNV Type Approved, we can also offer project specific DNV certification of individual Spreader Beams. It is the ultimate in certification and quality control for the most demanding project specification; a Modulift Spreader Beam individually certified y DNV in terms of design, manufacturing and Proof Load testing. Supplied with a design review report and Certificate of Conformity for Manufacture and Test, issued y DNV. 8
Enhanced QA Options/Custom Design Solutions Modulift recognise the high level QA requirements of the Oil & Gas, Offshore and Renewale Energy industries. In response to these high standards Modulift offer Enhanced QA Options to our standard Off-the-Shelf range of Spreader Beams - see our options list elow. Design Product Specification Off-the-Shelf BS EN 13155-2003, BS EN 1993-1 - 1-2005 ASME B30.20-2010, AS 4991-2004, DNV 2.22 Enhanced QA Options Project Specific requirements Materials Impact tested to -20 C /-4 F in accordance with BS EN10025/10210/10219 Impact tested to -40 C /-40 F in accordance with BS EN 10025/10225/API SL Welding BS EN ISO 15614.1 Paint Finish MOD 1600 Standard Finish - Yellow RAL 1003 2 Pack epoxy paint system High uild systems suitale for marine environments Markings Engraved stainless steel ID plate ID plate and additional laelling Testing - Proof Load Testing & NDT Bolts Grade 8.8 HT zinc plated Low temperature, galvanised Shackles Rated to -20 C /-4 F Rated to -40 C /-40 F Slings Rated to -40 C/ -40 F and BS EN 13414-1 & -3 compliant MOD 1000 Verification Off-the-Shelf Enhanced QA Options DNV Type Approval DNV Design Approval Original Design Verification Proof Load Test Jo specific Proof Load Testing & NDT on individual eams x MOD 600 Third Party Verification of individual eams x Certification / Documentation Off-the-Shelf Enhanced QA Options MOD 400 EC Declaration of MOD Conformity 1000 User Instructions Material Certification x Inspection and Test Plan (ITP) x Welding, NDT & MOD Proof 600 Load Testing documentation x MRB (Manufactures Record Book) x 9
Accessories SHACKLES & SLINGS Modulift can supply shackle sets and s to suit all rigging requirements. Sling Types: Round Slings, Chain Slings, Flat Weing Slings, Wire Rope Slings and Cale Laid Slings & Grommets to BS EN 13414-1 & 3. Shackles generally conform to EN 13889 and US Fed Spec RR-C-271. Summary of the sizes of Shackles that are required for the Modulift Modular Spreader Beam Range: Modulift Spreader Series Bottom Shackle Size Top Shackle Size Van Beest Model Numer The Crosy Group Model Numer MOD 6 3.25t 4.75t G - 4163 G - 2130 MOD 12 6.5t 8.5t G - 4163 G - 2130 MOD 24 12t 17t G - 4163 G - 2130 MOD 34 17t 25t G - 4163 G - 2130 MOD 50 25t 35t G - 4163 G - 2130 MOD 70 35t 55t G - 4163 G - 2130 MOD 70H 55t 85t G - 4163 G - 2130 MOD 110 55t 85t G - 4163 G - 2130 MOD 110H 85t 120t G - 163/P-6036 G - 2130 MOD 110SH 120t 150t P - 6036 MOD 250 125t-200t 200t-300t P - 6033 MOD 400 200t-400t 300t-400t P - 6033 MOD 600 200t-500t 300t-600t P - 6033 All Modulift shackles recommended are DNV Type Approved. 10
Accessories LOGISTIC CRADLES Modulift Logistic Cradles are an essential part of safe and efficient handling and storage of Modulift Systems. Designed with a storage position for each component, the cradles enale instant recognition of any missing components. Cradles can e produced to suit any rig comination. Other design features can include fork pockets, stacking feet, lifting points, tool storage and security cases for locking. ACCESSORIES - DELTA PLATES AND CLEVIS S A range of alternatives to standard Drop Links are availale to help you with your rigging needs. Clevis Drop Links will rotate the shackle orientation y 90 degrees. Delta Plates enale 2 s to e connected with separate shackles. ASSEMBLY AIDS The Modulift Drop Link Assemly Aids are a tool used when rigging drop links into heavier Spreader Beams. It enales the drop link to e supported and aligned in position while a shackle is eing fitted. Drop Link Assemly Aids are availale for the MOD 250 and larger sizes (must e asked for at time of ordering). STEP DOWN S AND CONE ADAPTORS For requirements with longer spans and lighter loads, these enale a Spreader System to e optimised to suit a particular need. Step Down End Units are designed for smaller sizes up to MOD 70. Cone Adaptors are used for the larger sizes. FASTENERS Modulift olts, nuts and washers are specifically supplied for each Spreader Beam assemly; see individual User Instructions in the following pages for details. Additional fasteners that are Modulift approved can e purchased at any time. 11
Engineering Design and Lift Management Custom lifting solutions; innovative, approved safety, effective, on udget and on time With over 20 years of specialist lifting experience, Modulift is expert in designing and manufacturing any manner of complicated or excessively heavy lifting project. At the forefront of every lift, Modulift maintains the very highest standards of risk management while ensuring a safe lifting environment. With a team of highly trained specialist in-house Lifting Engineers, Project Consultants, Rig Planning Services and On-Site Support, Modulift can deliver an extensive personalised package which will guide you through from your initial enquiry up to the day of your successful lift. Using amongst the most Quality Assured products in the lifting industry, Modulift can design and uild to the very highest gloal standards. Enhanced with a custom integrated service, Modulift can ensure a safe, cost efficient lift on time, every time. Lifting solutions made easy 1. Simple Single Beam 2 point Lift A single Spreader Beam is the simplest configuration and is suitale for 2 point lifts. The Spreader Beam asors the compression forces to protect the load eing lifted. 2. Single Beam 4 Point Lift This configuration again used a single eam where the load eing lifted has four individual lifting points. 3. 1-Over-2 Rig We use this configuration when vertical s are essential for 4 point lifts. By varying the lengths, we can also take into account an offset center of gravity. 4. 1-Over-2 Inline Rig Ideal for those lifts where the span is long and potential ending of the load is a prolem. Further cascading layers are availale to increase the numer of lifting points 12
Engineering Design and Lift Management 5. 1-Over-1 Where there are an uneven numer of points to lift from a 1 over 1 system can e used to lift the load whilst still providing a alanced rig. 6. Various Multi Spreader Beam Rigs With our expert help we can address most lifting issues using a comination of our products to fit the application and the circumstances. 7. CMOD Spreader Frame The CMod spreader frame uses corner units to connect existing Modulift struts into a 4 point modular spreader frame. This uses less headroom than a 1 over 2 rig. 8. Lifting Frame (H Frame) For extremely low headroom applications, Modulift can design and faricate a espoke lifting frame to suit your exact requirements Using these Rig Design options, Modulift can provide purpose-uilt lifting equipment which takes in to account all the necessary elements such as load type and weight, height restrictions, environmental factors, Centre of Gravity composition for example, to deploy a safe and strategic lift. Modulift team memers are availale and on-hand every step of the way, assisting in producing an effective and smooth-running project. 13
Engineering Design and Lift Management Modulift Custom Process Flow Call today to discuss your Custom Designed & Managed Lifting Project Tel: +44 (0) 1202 621511 14
QuickJoint 2 What is a QuickJoint? - It s only the future says Modulift The QuickJoint 2 (QJ2) is the smaller addition to the Modulift Spreader System. QuickJoint has a similar arrangement to the standard Modulift Spreader System and retains all the flexiility with the improved aility to e assemled quickly. QJ2: WLL 2 Tonnes to 1.2m The compact size and lightness of the QuickJoint rings a new reality that Spreader Beams don t have to e ulky and difficult to take to site. The convenient carry case will ensure that QuickJoint is easy to store, transport and used in applications such as in machinery assemly, installation and maintenance. Applications: Mechanical and Machinery Installation Mechanical and Machinery Maintenance Aerospace Maintenance Ship s Machinery Maintenance Process Equipment Maintenance Features: Fast assemly due to QJ2 design Lightweight: Less than 8kg Handy carry case enales the QJ2 to e easily moved to a worksite efore assemly BENEFITS: QJ2 s light weight aids compliance with Manual Handling Regulations and PUWER Rapid assemly TYPICAL QUICKJOINT ASSEMBLY QuickJoint 2 - The future of portale eams 1. You Wanted Fast Assemly We wanted to give you a Spreader System that is quick and simple to assemle and so our team came up with the QuickJoint Design! 2. Strong But Lightweight The entire set of components weighs less than 8 kgs for true portaility and great duraility 3. Handy Carry Case Our carry case enales the QuickJoint to e easily moved to a worksite efore assemly. 4. Multiple Applications QJ2 can e used for a variety of applications, including installation, maintenance, aerospace and process equipment maintenance. QUICK RELEASE PIN: Load v / m 45 Recommended Min.Top Sling Length Configuration. EU - End Unit (0.15m) 30 15 Min.Top Sling Length 300 2 0.25 EU EU 300 2 0.3 400 2 0.28 EU 100 EU 400 2 0.4 500 2 0.36 EU 200 EU 500 2 0.5 600 2 0.43 EU 300 EU 600 2 0.6 700 2 0.50 EU 300 100 EU 700 2 0.7 800 2 0.57 EU 300 200 EU 800 2 0.8 900 2 0.64 EU 300 300 EU 900 2 0.9 1000 2 0.71 EU 300 300 100 EU 1000 2 1.0 1100 2 0.78 EU 300 300 200 EU 1100 2 1.1 1200 2 0.85 EU 100 300 300 200 EU 1200 2 1.2
MOD 6 The MOD 6 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 6 has an assemled span ranging from 400mm to 2.5m which can e achieved in 100mm increments. β = Sling to Vertical angle - 1m 0.6m 0.3m 0 0.2m Fig. 1: Typical Spreader Assemly. 0.1m 4.75t SHACKLE 3.25t SHACKLE 0 M10X30, GRADE 8.8, HT BOLTS, Load v 45 Top Min Sling Recommended Configuration EU - End Unit (0.2m) = SLING TO VERTICAL ANGLE, ß 30 Sling 400 6 0.3 EU EU 400 6 0.4 500 6 0.4 EU 100 EU 500 6 0.5 600 6 0.5 EU 200 EU 600 6 0.6 700 6 0.5 EU 300 EU 700 6 0.7 800 6 0.6 EU 300 100 EU 800 6 0.8 900 6 0.7 EU 300 200 EU 900 6 0.9 1000 6 0.7 EU 600 EU 1000 6 1.0 1100 6 0.8 EU 600 100 EU 1100 6 1.1 1200 6 0.9 EU 600 200 EU 1200 6 1.2 1300 6 0.9 EU 600 300 EU 1300 6 1.3 1400 6 1.0 EU 1000 EU 1400 6 1.4 1500 6 1.1 EU 1000 100 EU 1500 6 1.5 1600 6 1.2 EU 1000 200 EU 1600 6 1.6 1700 6 1.2 EU 1000 300 EU 1700 6 1.7 1800 6 1.3 EU 1000 300 100 EU 1800 6 1.8 1900 6 1.4 EU 1000 300 200 EU 1900 6 1.9 2000 6 1.5 EU 1000 600 EU 2000 6 2.0 2100 6 1.5 EU 600 1000 100 EU 2100 6 2.1 2200 6 1.6 EU 600 1000 200 EU 2200 6 2.2 2300 6 1.6 EU 600 1000 300 EU 2300 6 2.3 2400 6 1.7 EU 600 1000 300 100 EU 2400 6 2.4 2500 6 1.8 EU 600 1000 300 200 EU 2500 6 2.5 Mod 6 - SYSTEM Specification Rated at 6 tonnes at 2.5m span Sling to vertical angle, ß, 45 degrees End units and drop links are rated at 3 tonnes (6 tonnes comined capacity) Bolt tightening torque: 60Nm ner size required: 17mm 16
MOD 12 The MOD 12 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 12 has an assemled span ranging from 0.5m to 4m which can e achieved in 0.25m increments. β = Sling to Vertical angle 0-1.5m 0 1m 0.75m 0.5m Fig. 1: Typical Spreader Assemly. 0.25m 8.5t SHACKLE 6.5t SHACKLE M12X35, GRADE 8.8, HT BOLTS, Load v 45 Min TOP Sling Recommended Configuration EU - End Unit (0.25m) = SLING TO VERTICAL ANGLE, ß 30 Min TOP Sling 0.5 12 0.4 EU EU 0.5 12 0.5 0.75 12 0.6 EU 0.25 EU 0.75 12 0.75 1 12 0.8 EU 0.5 EU 1 12 1.0 1.25 12 0.9 EU 0.75 EU 1.25 12 1.25 1.5 12 1.1 EU 1 EU 1.5 12 1.5 1.75 12 1.2 EU 1 0.25 EU 1.75 12 1.75 2 12 1.5 EU 1.5 EU 2 12 2 2.25 12 1.6 EU 1.5 0.25 EU 2.25 12 2.25 2.5 12 1.8 EU 1.5 0.5 EU 2.5 12 2.75 2.75 12 2.0 EU 1.5 0.75 EU 2.75 12 2.75 3 12 2.2 EU 1.5 1 EU 3 12 3 3.25 11 2.3 EU 1 1.5 0.25 EU 3.25 12 3.25 3.5 10 2.5 EU 1 1.5 0.5 EU 3.5 12 3.5 3.75 8 2.7 EU 1 1.5 0.75 EU 3.75 12 3.75 4 7 2.9 EU 1 1.5 0.75 0.25 EU 4 12 4.0 Mod 12 - SYSTEM Specification Rated at 12 tonnes at 4m span Sling to verticle angle, ß, 45 degrees End units and drop links are rated at 6 tonnes (12 tonnes comined capacity) Bolt tightening torque: 90 Nm ner size required: 19mm 17
MOD 24 The MOD 24 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 24 has an assemled span ranging from 1m to 6m which can e achieved in 0.5m increments. β = Sling to Vertical angle - 2m 1m 0.5m 17t SHACKLE Fig. 1: Typical Spreader Assemly. 12t SHACKLE M20X50 GRADE 8.8 HT BOLTS, Load v 45 Sling Recommended Configuration EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30 Sling 1 24 0.7 EU EU 1 24 1.0 1.5 24 1.1 EU 0.5 EU 1.5 24 1.5 2 24 1.5 EU 1 EU 2 24 2.0 2.5 24 1.8 EU 1 0.5 EU 2.5 24 2.5 3 24 2.2 EU 2 EU 3 24 3.0 3.5 22 2.5 EU 2 0.5 EU 3.5 24 3.5 4 18 2.9 EU 2 1 EU 4 24 4.0 Mod 24 - SYSTEM Specification Rated at 24 tonnes at 3m span Sling to Vertical ß, 45 degrees or less End units and drop links are rated at 12 tonnes (24 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 4.5 15 3.2 EU 0.5 2 1 EU 4.5 24 4.5 5 12 3.6 EU 2 2 EU 5 21 5.0 5.5 10 3.9 EU 2 2 0.5 EU 5.5 17 5.5 6 8 4.3 EU 2 2 1 EU 6 14 6.0 18
MOD 34 The MOD 34 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 34 has an assemled span ranging from 1 m to 8 m which can e achieved in 0.5 m increments. β = Sling to Vertical angle - 2m 1m 0.5m 25t SHACKLE Fig. 1: Typical Spreader Assemly. 17t SHACKLE M20X50, GRADE 8.8, HT BOLTS, Load v 45 Sling Recommended Configuration EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30 Sling Length /m 1 34 0.7 EU EU 1 34 1.0 1.5 34 1.1 EU 0.5 EU 1.5 34 1.5 2 34 1.5 EU 1 EU 2 34 2.0 2.5 34 1.8 EU 1 0.5 EU 2.5 34 2.5 3 34 2.2 EU 2 EU 3 34 3.0 3.5 32 2.5 EU 2 0.5 EU 3.5 34 3.5 4 29 2.9 EU 2 1 EU 4 34 4.0 4.5 25 3.2 EU 0.5 2 1 EU 4.5 34 4.5 5 21 3.6 EU 2 2 EU 5 34 5.0 5.5 18 3.9 EU 2 2 0.5 EU 5.5 31 5.5 6 15 4.3 EU 2 2 1 EU 6 26 6.0 6.5 13 4.6 EU 0.5 2 2 1 EU 6.5 22 6.5 7 11 5.0 EU 2 2 2 EU 7 19 7.0 7.5 9 5.3 EU 0.5 2 2 2 EU 7.5 16 7.5 8 8 5.7 EU 2 2 2 1 EU 8 14 8.0 Mod 34 - SYSTEM Specification Rated at 34 tonnes at 12 span Base to Sling Angle, a, 45 degrees or less End units and drop links are rated at 17 tonnes (34 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 19
MOD 50 The MOD 50 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 50 has an assemled span ranging from 1m to 11m which can e achieved in 0.5m increments. β = Sling to Vertical angle - 4m 2m 1m 0.5m Fig. 1: Typical Spreader Assemly. 35t SHACKLE 25t SHACKLE M20X65 HT BOLTS, NUTS & WASHERS Load v 45 /t Sling Recommended Configuration EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30 Sling Mod 50 - SYSTEM Specification Rated at 50 tonnes at 6m span 1 50 0.7 EU EU 1 50 1.0 1.5 50 1.1 EU 0.5 EU 1.5 50 1.5 2 50 1.5 EU 1 EU 2 50 2.0 2.5 50 1.8 EU 1 0.5 EU 2.5 50 2.5 3 50 2.2 EU 2 EU 3 50 3.0 3.5 50 2.5 EU 2 0.5 EU 3.5 50 3.5 4 50 2.9 EU 2 1 EU 4 50 4 4.5 50 3.2 EU 0.5 2 1 EU 4.5 50 4.5 5 50 3.6 EU 2 2 EU 5 50 5 5.5 50 3.9 EU 2 2 0.5 EU 5.5 50 5.5 6 50 4.3 EU 2 2 1 EU 6 50 6 6.5 42 4.6 EU 0.5 2 2 1 EU 6.5 50 6.5 7 35 5.0 EU 2 2 2 EU 7 50 7 7.5 29 5.3 EU 0.5 2 2 2 EU 7.5 50 7.5 8 25 5.7 EU 2 2 2 1 EU 8 43 8 8.5 22 6.0 EU 0.5 1 4 2 EU 8.5 38 8.5 9 19 6.4 EU 4 4 EU 9 33 9 9.5 17 6.8 EU 4 4 0.5 EU 9.5 29 9.5 10 15 7.1 EU 4 4 1 EU 10 26 10 10.5 13 7.5 EU 1 4 4 0.5 EU 10.5 22 10.5 11 11 7.8 EU 2 4 4 EU 11 19 11 Sling to Verticle angle, ß 45 degrees End units and drop links are rated at 25 tonnes (50 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 20
MOD 50/24: Step-Downs The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 50/24 has an assemled span ranging from 1 metre to 11 metres in 0.5 metre increments. - ß = Sling to Vertical angle Fig.1: Typical Spreader Assemly. STEP DOWN Load v /m 45º Recommended Configuration. EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30º 1 24 0.7 EU EU 1 24 1 1.5 24 1.1 EU 0.5 EU 1.5 24 1.5 2 24 1.5 EU 1 EU 2 24 2 2.5 24 1.8 EU 1 0.5 EU 2.5 24 2.5 3 24 2.2 EU 2 EU 3 24 3 3.5 24 2.5 EU 2 0.5 EU 3.5 24 3.5 4 24 2.9 EU 2 1 EU 4 24 4 4.5 24 3.2 EU 0.5 2 1 EU 4.5 24 4.5 5 24 3.6 EU 4 EU 5 24 5 5.5 24 3.9 EU 4 0.5 EU 5.5 24 5.5 6 24 4.3 EU 4 1 EU 6 24 6 6.5 24 4.6 EU 0.5 4 1 EU 6.5 24 6.5 7 24 5.0 EU 4 2 EU 7 24 7 7.5 24 5.3 EU 0.5 4 2 EU 7.5 24 7.5 8 24 5.7 EU 1 4 2 EU 8 24 8 8.5 22 6.0 EU 0.5 1 4 2 EU 8.5 24 8.5 9 19 6.4 EU 4 4 EU 9 24 9 9.5 17 6.8 EU 4 4 0.5 EU 9.5 24 9.5 10 15 7.1 EU 4 4 1 EU 10 24 10 10.5 13 7.5 EU 1 4 4 0.5 EU 10.5 22 10.5 11 11 7.8 EU 2 4 4 EU 11 19 11 (STEP DOWN) (MOD 24) 4.0m 2.0m 1.0m 0.5m 17t SHACKLE 12t SHACKLE M20x65 HT BOLTS, Mod 50/24 - SYSTEM Specification Rated at 24 tonnes at 8m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 12 tonnes (24 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 21
MOD 50/12: Step-Downs The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 50/12 has an assemled span ranging from 1 metre to 11 metres in 0.5 metre increments. - ß = Sling to Vertical angle Fig.1: Typical Spreader Assemly. STEP DOWN Load v /m 45º Recommended Configuration. EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30º 1 12 0.7 EU EU 1 12 1 1.5 12 1.1 EU 0.5 EU 1.5 12 1.5 2 12 1.5 EU 1 EU 2 12 2 2.5 12 1.8 EU 1 0.5 EU 2.5 12 2.5 3 12 2.2 EU 2 EU 3 12 3 3.5 12 2.5 EU 2 0.5 EU 3.5 12 3.5 4 12 2.9 EU 2 1 EU 4 12 4 4.5 12 3.2 EU 0.5 2 1 EU 4.5 12 4.5 5 12 3.6 EU 4 EU 5 12 5 5.5 12 3.9 EU 4 0.5 EU 5.5 12 5.5 6 12 4.3 EU 4 1 EU 6 12 6 6.5 12 4.6 EU 0.5 4 1 EU 6.5 12 6.5 7 12 5.0 EU 4 2 EU 7 12 7 7.5 12 5.3 EU 0.5 4 2 EU 7.5 12 7.5 8 12 5.7 EU 1 4 2 EU 8 12 8 8.5 12 6.0 EU 0.5 1 4 2 EU 8.5 12 8.5 9 12 6.4 EU 4 4 EU 9 12 9 9.5 12 6.8 EU 4 4 0.5 EU 9.5 12 9.5 10 12 7.1 EU 4 4 1 EU 10 12 10 10.5 12 7.5 EU 1 4 4 0.5 EU 10.5 12 10.5 11 11 7.8 EU 2 4 4 EU 11 12 11 (STEP DOWN) (MOD 12) 4.0m 2.0m 1.0m 0.5m 8.5t SHACKLE 6.5t SHACKLE M20x65 HT BOLTS, Mod 50/12 - SYSTEM Specification Rated at 12 tonnes at 10.5m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 6 tonnes (12 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 22
MOD 50/6: Step-Downs The MOD 6 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 50/6 has an assemled span ranging from 1m to 11m which can e achieved in 0.5m increments. - ß = Sling to Vertical angle Fig.1: Typical Spreader Assemly. STEP DOWN Load v 45 Top Min Sling Recommended Configuration EU - End Unit (0.2m) = SLING TO VERTICAL ANGLE, ß 30 Sling 1 6 0.7 EU EU 1 6 1 1.5 6 1.1 EU 0.5 EU 1.5 6 1.5 2 6 1.5 EU 1 EU 2 6 2 2.5 6 1.8 EU 1 0.5 EU 2.5 6 2.5 3 6 2.2 EU 2 EU 3 6 3 3.5 6 2.5 EU 2 0.5 EU 3.5 6 3.5 4 6 2.9 EU 2 1 EU 4 6 4 4.5 6 3.2 EU 0.5 2 1 EU 4.5 6 4.5 5 6 3.6 EU 4 EU 5 6 5 5.5 6 3.9 EU 4 0.5 EU 5.5 6 5.5 6 6 4.3 EU 4 1 EU 6 6 6 6.5 6 4.6 EU 0.5 4 1 EU 6.5 6 6.5 7 6 5.0 EU 4 2 EU 7 6 7 7.5 6 5.3 EU 0.5 4 2 EU 7.5 6 7.5 8 6 5.7 EU 1 4 2 EU 8 6 8 8.5 6 6.0 EU 0.5 1 4 2 EU 8.5 6 8.5 9 6 6.4 EU 4 4 EU 9 6 9 9.5 6 6.8 EU 4 4 0.5 EU 9.5 6 9.5 10 6 7.1 EU 4 4 1 EU 10 6 10 10.5 6 7.5 EU 1 4 4 0.5 EU 10.5 6 10.5 11 6 7.8 EU 2 4 4 EU 11 6 11 (STEP DOWN) 4.0m 2.0m 1.0m 0.5m 4.75t SHACKLE 3.25t SHACKLE M20x65 HT BOLTS, Mod 6 - SYSTEM Specification Rated at 6 tonnes at 11m span Sling to vertical angle, ß, 45 degrees End units and drop links are rated at 3 tonnes (6 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 23
MOD 70 The MOD 70 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 70 has an assemled span ranging from 1m to 12m which can e achieved in 0.5m increments. β = Sling to Vertical angle - 4m 2m 1m TRUT 0.5m Fig.1: Typical Spreader Assemly. Fig. 1: Typical Spreader Assemly. 55t SHACKLE 35t SHACKLE M20X65, GRADE 8.8 HT BOLTS, Load v /m 45 Sling Length /m Recommended Configuration EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß /m 30 Sling 1 70 0.7 EU EU 1 70 1 1.5 70 1.1 EU 0.5 EU 1.5 70 1.5 2 70 1.5 EU 1 EU 2 70 2 2.5 70 1.8 EU 1 0.5 EU 2.5 70 2.5 3 70 2.2 EU 2 EU 3 70 3 3.5 70 2.5 EU 2 0.5 EU 3.5 70 3.5 4 70 2.9 EU 2 1 EU 4 70 4 4.5 70 3.2 EU 0.5 2 1 EU 4.5 70 4.5 5 70 3.6 EU 4 EU 5 70 5 5.5 70 3.9 EU 4 0.5 EU 5.5 70 5.5 6 70 4.3 EU 4 1 EU 6 70 6 6.5 70 4.6 EU 0.5 4 1 EU 6.5 70 6.5 7 70 5.0 EU 4 2 EU 7 70 7 7.5 67 5.3 EU 0.5 4 2 EU 7.5 70 7.5 8 58 5.7 EU 1 4 2 EU 8 70 8 8.5 51 6.0 EU 0.5 1 4 2 EU 8.5 70 8.5 9 44 6.4 EU 4 4 EU 9 70 9 9.5 39 6.8 EU 4 4 0.5 EU 9.5 68 9.5 10 34 7.1 EU 4 4 1 EU 10 59 10 10.5 30 7.5 EU 1 4 4 0.5 EU 10.5 53 10.5 11 27 7.8 EU 2 4 4 EU 11 47 11 11.5 25 8.2 EU 2 4 4 0.5 EU 11.5 43 11.5 12 22 8.5 EU 2 4 4 1 EU 12 38 12 Mod 70 - SYSTEM Specification Rated at 70 tonnes at 7m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 35 tonnes (70 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 24
MOD 70H The MOD 70H Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 70H has an assemled span ranging from 1m to 12m which can e achieved in 0.5m increments. β = Sling to Vertical angle - 4m 2m 1m 0.5m Fig.1: Typical Spreader Assemly. Fig. 1: Typical Spreader Assemly. 85t SHACKLE 55t SHACKLE M20X65, GRADE 8.8 HT BOLTS, Load v /m 45 Sling Length /m Recommended Configuration EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30 Sling 1 100 0.7 EU EU 1 100 1 1.5 100 1.1 EU 0.5 EU 1.5 100 1.5 2 100 1.5 EU 1 EU 2 100 2 2.5 100 1.8 EU 1 0.5 EU 2.5 100 2.5 3 100 2.2 EU 2 EU 3 100 3 3.5 100 2.5 EU 2 0.5 EU 3.5 100 3.5 Mod 70H - SYSTEM Specification Rated at 100 tonnes at 6m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 50 tonnes (100 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 4 100 2.9 EU 2 1 EU 4 100 4 4.5 100 3.2 EU 0.5 2 1 EU 4.5 100 4.5 5 100 3.6 EU 2 2 EU 5 100 5 5.5 100 3.9 EU 2 2 0.5 EU 5.5 100 5.5 6 100 4.3 EU 2 2 1 EU 6 100 6 6.5 88 4.6 EU 0.5 2 2 1 EU 6.5 100 6.5 7 76 5.0 EU 2 2 2 EU 7 100 7 7.5 67 5.3 EU 0.5 2 2 2 EU 7.5 100 7.5 8 58 5.7 EU 2 2 2 1 EU 8 100 8 8.5 51 6.0 EU 0.5 1 4 2 EU 8.5 89 8.5 9 44 6.4 EU 4 4 EU 9 77 9 9.5 39 6.8 EU 4 4 0.5 EU 9.5 68 9.5 10 34 7.1 EU 4 4 1 EU 10 59 10 10.5 30 7.5 EU 1 4 4 0.5 EU 10.5 53 10.5 11 27 7.8 EU 2 4 4 EU 11 47 11 11.5 25 8.2 EU 2 4 4 0.5 EU 11.5 43 11.5 12 22 8.5 EU 2 4 4 1 EU 12 38 12 25
MOD 70/34: Step-Downs The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 70/34 has an assemled span ranging from 1 metre to 12 metres in 0.5 metre increments. ß = Sling to Vertical angle - Fig.1: Typical Spreader Assemly. STEP DOWN Load v /m 45º Recommended Configuration. EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30º 1 34 0.7 EU EU 1 34 1 1.5 34 1.1 EU 0.5 EU 1.5 34 1.5 2 34 1.5 EU 1 EU 2 34 2 2.5 34 1.8 EU 1 0.5 EU 2.5 34 2.5 3 34 2.2 EU 2 EU 3 34 3 3.5 34 2.5 EU 2 0.5 EU 3.5 34 3.5 4 34 2.9 EU 2 1 EU 4 34 4 4.5 34 3.2 EU 0.5 2 1 EU 4.5 34 4.5 5 34 3.6 EU 4 EU 5 34 5 5.5 34 3.9 EU 4 0.5 EU 5.5 34 5.5 6 34 4.3 EU 4 1 EU 6 34 6 6.5 34 4.6 EU 0.5 4 1 EU 6.5 34 6.5 7 34 5.0 EU 4 2 EU 7 34 7 7.5 34 5.3 EU 0.5 4 2 EU 7.5 34 7.5 8 34 5.7 EU 1 4 2 EU 8 34 8 8.5 34 6.0 EU 0.5 1 4 2 EU 8.5 34 8.5 9 34 6.4 EU 4 4 EU 9 34 9 9.5 34 6.8 EU 4 4 0.5 EU 9.5 34 9.5 10 34 7.1 EU 4 4 1 EU 10 34 10 10.5 30 7.5 EU 1 4 4 0.5 EU 10.5 34 10.5 11 27 7.8 EU 2 4 4 EU 11 34 11 11.5 25 8.2 EU 2 4 4 0.5 EU 11.5 34 11.5 12 22 8.5 EU 2 4 4 1 EU 12 34 12 (STEP DOWN) (MOD 34) 4.0m 2.0m 1.0m 0.5m 25t SHACKLE 17t SHACKLE M20x65 HT BOLTS, Mod 70/34 - SYSTEM Specification Rated at 34 tonnes at 10m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 17 tonnes (34 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 26
MOD 70/24: Step-Downs The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 70/24 has an assemled span ranging from 1 metre to 12 metres in 0.5 metre increments. ß = Sling to Vertical angle - Fig.1: Typical Spreader Assemly. STEP DOWN Load v /m 45º Recommended Configuration. EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30º 1 24 0.7 EU EU 1 24 1 1.5 24 1.1 EU 0.5 EU 1.5 24 1.5 2 24 1.5 EU 1 EU 2 24 2 2.5 24 1.8 EU 1 0.5 EU 2.5 24 2.5 3 24 2.2 EU 2 EU 3 24 3 3.5 24 2.5 EU 2 0.5 EU 3.5 24 3.5 4 24 2.9 EU 2 1 EU 4 24 4 4.5 24 3.2 EU 0.5 2 1 EU 4.5 24 4.5 5 24 3.6 EU 4 EU 5 24 5 5.5 24 3.9 EU 4 0.5 EU 5.5 24 5.5 6 24 4.3 EU 4 1 EU 6 24 6 6.5 24 4.6 EU 0.5 4 1 EU 6.5 24 6.5 7 24 5.0 EU 4 2 EU 7 24 7 7.5 24 5.3 EU 0.5 4 2 EU 7.5 24 7.5 8 24 5.7 EU 1 4 2 EU 8 24 8 8.5 24 6.0 EU 0.5 1 4 2 EU 8.5 24 8.5 9 24 6.4 EU 4 4 EU 9 24 9 9.5 24 6.8 EU 4 4 0.5 EU 9.5 24 9.5 10 24 7.1 EU 4 4 1 EU 10 24 10 10.5 24 7.5 EU 1 4 4 0.5 EU 10.5 24 10.5 11 24 7.8 EU 2 4 4 EU 11 24 11 11.5 24 8.2 EU 2 4 4 0.5 EU 11.5 24 11.5 12 22 8.5 EU 2 4 4 1 EU 12 24 12 (STEP DOWN) (MOD 24) 4.0m 2.0m 1.0m 0.5m 17t SHACKLE 12t SHACKLE M20x65 HT BOLTS, Mod 70/34 - SYSTEM Specification Rated at 24 tonnes at 11.5m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 12 tonnes (24 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 27
MOD 110 The MOD 110 Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 110 has an assemled span ranging from 2m to 16m which can e achieved in 0.5m increments. β = Sling to Vertical angle - 4m 2m 1m 0.5 Fig.1: Typical Spreader Assemly. Fig. 1: Typical Spreader Assemly. 85t SHACKLE 55t SHACKLE Load v M20X65 HT BOLTS, NUTS & WASHERS /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 Sling 2 110 1.5 EU EU 2 110 2 2.5 110 1.8 EU 0.5 EU 2.5 110 2.5 3 110 2.2 EU 1 EU 3 110 3 3.5 110 2.5 EU 1 0.5 EU 3.5 110 3.5 4 110 2.9 EU 2 EU 4 110 4 4.5 110 3.2 EU 2 0.5 EU 4.5 110 4.5 5 110 3.6 EU 2 1 EU 5 110 5 5.5 110 3.9 EU 0.5 2 1 EU 5.5 110 5.5 6 110 4.3 EU 2 2 EU 6 110 6 6.5 109 4.6 EU 2 2 0.5 EU 6.5 110 6.5 7 106 5.0 EU 2 2 1 EU 7 110 7 7.5 102 5.3 EU 0.5 2 2 1 EU 7.5 110 7.5 8 98 5.7 EU 2 2 2 EU 8 110 8 8.5 93 6.0 EU 0.5 2 2 2 EU 8.5 110 8.5 9 88 6.4 EU 2 2 2 1 EU 9 110 9 9.5 83 6.8 EU 0.5 1 4 2 EU 9.5 110 9.5 10 78 7.1 EU 4 4 EU 10 110 10 10.5 72 7.5 EU 4 4 0.5 EU 10.5 110 10.5 11 66 7.8 EU 4 4 1 EU 11 110 11 11.5 62 8.2 EU 0.5 4 4 1 EU 11.5 107 11.5 12 58 8.5 EU 2 4 4 EU 12 100 12 12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 92 12.5 13 48 9.5 EU 2 4 4 1 EU 13 84 13 13.5 45 9.75 EU 2 4 4 1 0.5 EU 13.5 80 13.5 14 43 10.0 EU 4 4 4 EU 14 75 14 14.5 39 10.25 EU 0.5 4 4 4 EU 14.5 69 14.5 15 35 10.5 EU 4 4 4 1 EU 15 62 15 15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5 16 31 11.5 EU 4 4 4 2 EU 16 53 16 Mod 110 - SYSTEM Specification Rated at 110 tonnes at 6m span. Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 55 tonnes 110 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 28
MOD 110H The MOD 110H Series is modular in length and each system consists of one pair of end units and drop links, with intermediate struts that can e assemled to achieve different spans. The MOD 110H has an assemled span ranging from 2m to 16m which can e achieved in 0.5m increments. Load v 45 4m 2m 1m 0.5m 120t SHACKLE 85t SHACKLE M20X65 HT BOLTS, NUTS & WASHERS Sling Length Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 Sling 2 125 1.5 EU EU 2 170 2 2.5 124 1.8 EU 0.5 EU 2.5 170 2.5 3 124 2.2 EU 1 EU 3 170 3 3.5 123 2.5 EU 1 0.5 EU 3.5 170 3.5 4 122 2.9 EU 2 EU 4 170 4 4.5 120 3.2 EU 2 0.5 EU 4.5 170 4.5 5 118 3.6 EU 2 1 EU 5 170 5 5.5 115 3.9 EU 0.5 2 1 EU 5.5 170 5.5 6 112 4.3 EU 2 2 EU 6 170 6 6.5 109 4.6 EU 2 2 0.5 EU 6.5 170 6.5 7 106 5.0 EU 2 2 1 EU 7 170 7 7.5 102 5.3 EU 0.5 2 2 1 EU 7.5 170 7.5 8 98 5.7 EU 2 2 2 EU 8 170 8 8.5 93 6.0 EU 0.5 2 2 2 EU 8.5 161 8.5 9 88 6.4 EU 2 2 2 1 EU 9 152 9 9.5 83 6.8 EU 0.5 1 4 2 EU 9.5 144 9.5 10 78 7.1 EU 4 4 EU 10 135 10 10.5 72 7.5 EU 4 4 0.5 EU 10.5 125 10.5 11 66 7.8 EU 4 4 1 EU 11 114 11 11.5 62 8.2 EU 0.5 4 4 1 EU 11.5 107 11.5 12 58 8.5 EU 2 4 4 EU 12 100 12 12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 92 12.5 13 48 9.5 EU 2 4 4 1 EU 13 84 13 13.5 45 9.75 EU 2 4 4 1 0.5 EU 13.5 80 13.5 14 43 10.0 EU 4 4 4 EU 14 75 14 14.5 39 10.25 EU 0.5 4 4 4 EU 14.5 69 14.5 15 35 10.5 EU 4 4 4 1 EU 15 62 15 15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5 16 31 11.5 EU 4 4 4 2 EU 16 53 16 β = Sling to Vertical angle Fig.1: Typical Spreader Assemly. Fig. 1: Typical Spreader Assemly. - Mod 110H - SYSTEM Specification Rated at 170 tonnes at 8m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 85 tonnes (170 tons comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 29
MOD 110SH The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 110SH has an assemled span ranging from 2m to 16m in 0.5m increments. β = Sling to Vertical angle - 4m 2m 1m Fig.1: Typical Spreader Assemly. Fig. 1: Typical Spreader Assemly. 0.5m 150t SHACKLE 120t SHACKLE M20X65 GRADE 8.8, HT BOLTS, Load v /m 45 Length Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 Length 2 158 1.5 EU EU 2 240 2 2.5 157 1.8 EU 0.5 EU 2.5 240 2.5 3 156 2.2 EU 1 EU 3 240 3 3.5 154 2.5 EU 1 0.5 EU 3.5 240 3.5 4 152 2.9 EU 2 EU 4 240 4 4.5 149 3.2 EU 2 0.5 EU 4.5 240 4.5 5 146 3.6 EU 2 1 EU 5 240 5 5.5 143 3.9 EU 0.5 2 1 EU 5.5 240 5.5 6 140 4.3 EU 2 2 EU 6 240 6 6.5 136 4.6 EU 2 2 0.5 EU 6.5 234 6.5 7 132 5.0 EU 2 2 1 EU 7 228 7 7.5 126 5.3 EU 0.5 2 2 1 EU 7.5 219 7.5 8 121 5.7 EU 2 2 2 EU 8 210 8 8.5 115 6.0 EU 0.5 2 2 2 EU 8.5 200 8.5 9 110 6.4 EU 2 2 2 1 EU 9 190 9 9.5 103 6.8 EU 0.5 1 4 2 EU 9.5 180 9.5 10 96 7.1 EU 4 4 EU 10 170 10 10.5 89 7.5 EU 4 4 0.5 EU 10.5 156 10.5 11 82 7.8 EU 4 4 1 EU 11 142 11 11.5 75 8.2 EU 1 4 4 0.5 EU 11.5 133 11.5 12 72 8.5 EU 2 4 4 EU 12 125 12 12.5 66 9.0 EU 2 4 4 0.5 EU 12.5 114 12.5 13 60 9.5 EU 2 4 4 1 EU 13 104 13 13.5 57 9.75 EU 2 4 4 1 0.5 EU 13.5 98 13.5 14 53 10.0 EU 4 4 4 EU 14 92 14 14.5 48 10.25 EU 0.5 4 4 4 EU 14.5 84 14.5 Mod 110SH - SYSTEM Specification Rated at 240 tonnes at 6m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 120 tonnes (240 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 15 44 10.5 EU 4 4 4 1 EU 15 76 15 15.5 41 11.0 EU 0.5 4 4 4 1 EU 15.5 71 15.5 16 38 11.5 EU 4 4 4 2 EU 16 66 16 30
MOD 110/70: Step-Downs The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 110/70 has an assemled span ranging from 1 metre to 16 metres in 0.5 metre increments. ß = Sling to Vertical angle - Fig.1: Typical Spreader Assemly. STEP DOWN Load v /m 45º Recommended Configuration. EU - End Unit (0.5m) = SLING TO VERTICAL ANGLE, ß 30º 2 70 1.5 EU EU 2 70 2 2.5 70 2.0 EU 0.5 EU 2.5 70 2.5 3 70 2.5 EU 1 EU 3 70 3 3.5 70 2.8 EU 1 0.5 EU 3.5 70 3.5 4 70 3.0 EU 2 EU 4 70 4 4.5 70 3.3 EU 2 1 EU 4.5 70 4.5 5 70 3.5 EU 2 1 EU 5 70 5 5.5 70 4.0 EU 0.5 2 1 EU 5.5 70 5.5 6 70 4.5 EU 4 EU 6 70 6 6.5 70 4.8 EU 2 2 0.5 EU 6.5 70 6.5 7 70 5.0 EU 4 1 EU 7 70 7 7.5 70 5.5 EU 0.5 2 2 1 EU 7.5 70 7.5 8 70 6.0 EU 4 2 EU 8 70 8 8.5 70 6.5 EU 0.5 2 2 2 EU 8.5 70 8.5 9 70 6.5 EU 4 2 1 EU 9 70 9 9.5 70 6.8 EU 0.5 1 4 2 EU 9.5 70 9.5 10 70 7.0 EU 4 4 EU 10 70 10 10.5 70 7.5 EU 4 4 0.5 EU 10.5 70 10.5 11 66 8.0 EU 4 4 1 EU 11 70 11 11.5 62 8.3 EU 1 4 1 0.5 EU 11.5 70 11.5 12 58 8.5 EU 4 4 2 EU 12 70 12 12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 70 12.5 13 48 9.5 EU 1 4 4 2 EU 13 70 13 13.5 45 9.8 EU 2 4 4 1 0.5 EU 13.5 70 13.5 14 43 10.0 EU 4 4 4 EU 14 70 14 14.5 39 10.3 EU 0.5 4 4 4 EU 14.5 67 14.5 15 35 10.5 EU 4 4 4 1 EU 15 62 15 15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5 16 31 11.5 EU 4 4 4 2 EU 16 53 16 (STEP DOWN) (MOD 70) 4.0m 2.0m 1.0m 0.5m 55t SHACKLE 35t SHACKLE M20x65 HT BOLTS, Mod 110/70 - SYSTEM Specification Rated at 70 tonnes at 10m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 35 tonnes (70 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 31
MOD 110/50: Step-Downs The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 110/50 has an assemled span ranging from 1 metre to 16 metres in 0.5 metre increments. - ß = Sling to Vertical angle Fig.1: Typical Spreader Assemly. STEP DOWN Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß Sling 2 110 1.5 EU EU 2 110 2 2.5 110 1.8 EU 0.5 EU 2.5 110 2.5 3 110 2.2 EU 1 EU 3 110 3 3.5 110 2.5 EU 1 0.5 EU 3.5 110 3.5 4 110 2.9 EU 2 EU 4 110 4 4.5 110 3.2 EU 2 0.5 EU 4.5 110 4.5 5 110 3.6 EU 2 1 EU 5 110 5 5.5 110 3.9 EU 0.5 2 1 EU 5.5 110 5.5 6 110 4.3 EU 2 2 EU 6 110 6 6.5 109 4.6 EU 2 2 0.5 EU 6.5 110 6.5 7 106 5.0 EU 2 2 1 EU 7 110 7 7.5 102 5.3 EU 0.5 2 2 1 EU 7.5 110 7.5 8 98 5.7 EU 2 2 2 EU 8 110 8 8.5 93 6.0 EU 0.5 2 2 2 EU 8.5 110 8.5 9 88 6.4 EU 2 2 2 1 EU 9 110 9 9.5 83 6.8 EU 0.5 1 4 2 EU 9.5 110 9.5 10 78 7.1 EU 4 4 EU 10 110 10 10.5 72 7.5 EU 4 4 0.5 EU 10.5 110 10.5 11 66 7.8 EU 4 4 1 EU 11 110 11 11.5 62 8.2 EU 0.5 4 4 1 EU 11.5 107 11.5 12 58 8.5 EU 2 4 4 EU 12 100 12 12.5 53 9.0 EU 2 4 4 0.5 EU 12.5 92 12.5 13 48 9.5 EU 2 4 4 1 EU 13 84 13 13.5 45 9.75 EU 2 4 4 1 0.5 EU 13.5 80 13.5 14 43 10.0 EU 4 4 4 EU 14 75 14 14.5 39 10.25 EU 0.5 4 4 4 EU 14.5 69 14.5 15 35 10.5 EU 4 4 4 1 EU 15 62 15 15.5 33 11.0 EU 0.5 4 4 4 1 EU 15.5 58 15.5 16 31 11.5 EU 4 4 4 2 EU 16 53 16 30 (STEP DOWN) (MOD 50) 4.0m 2.0m 1.0m 0.5m 35t SHACKLE 25t SHACKLE M20x65 HT BOLTS, Mod 110/50 - SYSTEM Specification Rated at 50 tonnes at 16m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 25 tonnes (50 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 32
MOD 250/250 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 250/250 has an assemled span ranging from 2 metres to 20m in 1m increments. ß = Sling to Vertical angle WLL 125t - WLL 125t 6m 3m 2m 1m 0 Fig. 1: Typical Spreader Assemly. 0.5m 200t WIDE BODY SHACKLE 125t WIDE BODY SHACKLE 0 M24X80 GRADE 8.8, HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 250 1.5 EU EU 2 250 2 3 250 2.5 EU 1 EU 3 250 3 4 250 3.0 EU 2 EU 4 250 4 5 250 3.5 EU 3 EU 5 250 5 6 250 4.5 EU 3 1 EU 6 250 6 7 250 5.0 EU 3 2 EU 7 250 7 8 244 6.0 EU 6 EU 8 250 8 9 228 6.5 EU 6 1 EU 9 250 9 10 212 7.0 EU 6 2 EU 10 250 10 11 194 8.0 EU 6 3 EU 11 250 11 12 178 8.5 EU 3 6 1 EU 12 250 12 13 158 9.5 EU 3 6 2 EU 13 250 13 14 140 10.0 EU 6 6 EU 14 242 14 15 122 10.5 EU 6 6 1 EU 15 211 15 16 106 11.5 EU 6 6 2 EU 16 183 16 17 94 12.0 EU 6 6 3 EU 17 163 17 18 82 13.0 EU 1 6 6 3 EU 18 142 18 19 70 13.5 EU 2 6 6 3 EU 19 121 19 20 52 14.5 EU 2 6 6 3 1 EU 20 90 20 Mod 250/250 - SYSTEM Specification Rated at 250 tonnes at 13m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 125 tonnes (250 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 33
MOD 250/300 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 250/300 has an assemled span ranging from 2 metres to 20m in 1m increments. β = Sling to Vertical angle WLL 150t - WLL 150t 6m 3m 2m 1m 0 Fig. 1: Typical Spreader Assemly. 0.5m 200t WIDE BODY SHACKLE 150t WIDE BODY SHACKLE 0 M24X80 GRADE 8.8, HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 278 1.5 EU EU 2 300 2 3 278 2.5 EU 1 EU 3 300 3 4 278 3.0 EU 2 EU 4 300 4 5 272 3.5 EU 3 EU 5 300 5 6 264 4.5 EU 3 1 EU 6 300 6 7 254 5.0 EU 3 2 EU 7 300 7 8 244 6.0 EU 6 EU 8 300 8 9 228 6.5 EU 6 1 EU 9 300 9 10 212 7.0 EU 6 2 EU 10 300 10 11 194 8.0 EU 6 3 EU 11 300 11 12 178 8.5 EU 3 6 1 EU 12 300 12 13 158 9.5 EU 3 6 2 EU 13 273 13 14 140 10.0 EU 6 6 EU 14 242 14 15 122 10.5 EU 6 6 1 EU 15 211 15 16 106 11.5 EU 6 6 2 EU 16 183 16 17 94 12.0 EU 6 6 3 EU 17 163 17 18 82 13.0 EU 1 6 6 3 EU 18 142 18 19 70 13.5 EU 2 6 6 3 EU 19 121 19 20 52 14.5 EU 3 6 6 2 1 EU 20 90 20 Mod 250/300 - SYSTEM Specification Rated at 300 tonnes at 12m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 150 tonnes (300 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 34
MOD 250/400 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 250/400 has an assemled span ranging from 2 metres to 20m in 1m increments. β = Sling to Vertical angle WLL 200t - WLL 200t 6m 3m 2m 1m 0 Fig. 1: Typical Spreader Assemly. 0.5m 300t WIDE BODY SHACKLE 0 200t WIDE BODY SHACKLE M24X80 GRADE 8.8, HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 300 1.5 EU EU 2 400 2 3 284 2.5 EU 1 EU 3 400 3 4 278 3.0 EU 2 EU 4 400 4 5 272 3.5 EU 3 EU 5 400 5 6 264 4.5 EU 3 1 EU 6 400 6 7 254 5.0 EU 3 2 EU 7 400 7 8 244 6.0 EU 6 EU 8 400 8 9 228 6.5 EU 6 1 EU 9 394 9 10 212 7.0 EU 6 2 EU 10 367 10 11 194 8.0 EU 6 3 EU 11 336 11 12 178 8.5 EU 3 6 1 EU 12 308 12 13 158 9.5 EU 3 6 2 EU 13 273 13 14 140 10.0 EU 6 6 EU 14 242 14 15 122 10.5 EU 6 6 1 EU 15 211 15 16 106 11.5 EU 6 6 2 EU 16 183 16 17 94 12.0 EU 6 6 3 EU 17 163 17 18 82 13.0 EU 1 6 6 3 EU 18 142 18 19 70 13.5 EU 2 6 6 3 EU 19 121 19 20 52 14.5 EU 3 6 6 2 1 EU 20 90 20 Mod 250/400 - SYSTEM Specification Rated at 400 tonnes at 8m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 200 tonnes (400 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 35
MOD 250/110H: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 250/110H has an assemled span ranging from 2 metres to 20 metres in 1 metre increments. β = Sling to Vertical angle - 0 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 2 170 1.5 EU EU 2 170 2 3 170 2.5 EU CA CA EU 3 170 3 4 170 3.0 EU CA 1 CA EU 4 170 4 5 170 3.5 EU CA 2 CA EU 5 170 5 6 170 4.5 EU CA 3 CA EU 6 170 6 7 170 5.0 EU CA 3 1 CA EU 7 170 7 8 170 6.0 EU CA 3 2 CA EU 8 170 8 9 170 6.5 EU CA 6 CA EU 9 170 9 10 170 7.0 EU CA 6 1 CA EU 10 170 10 11 170 8.0 EU CA 6 2 CA EU 11 170 11 12 170 8.5 EU CA 6 3 CA EU 12 170 12 13 158 9.5 EU CA 3 6 1 CA EU 13 170 13 14 140 10.0 EU CA 3 6 2 CA EU 14 170 14 15 122 10.5 EU CA 6 6 CA EU 15 170 15 16 106 11.5 EU CA 6 6 1 CA EU 16 170 16 17 94 12.0 EU CA 6 6 2 CA EU 17 163 17 18 82 13.0 EU CA 6 6 3 CA EU 18 142 18 19 70 13.5 EU CA 1 6 6 3 CA EU 19 121 19 20 52 14.5 EU CA 2 6 6 3 CA EU 20 90 20 0 1 - MOD 110H WLL 85t - MOD 110H WLL 85t 6.0m 3.0m 2.0m 1.0m 0.5 MOD 250/110 CONE ADAPTER 120t SHACKLE 85t SHACKLE MOD 250: M24x80 HT BOLTS, NUTS & WASHERS MOD 110H: M20x65 HT BOLTS, Mod 250/110H - SYSTEM Specification Rated at 170 tonnes at 16m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 85 tonnes (170 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 36
MOD 250/110: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 250/110 has an assemled span ranging from 2 metres to 20 metres in 1 metre increments. β = Sling to Vertical angle - 0 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 2 110 1.5 EU EU 2 110 2 3 110 2.5 EU CA CA EU 3 110 3 4 110 3.0 EU CA 1 CA EU 4 110 4 5 110 3.5 EU CA 2 CA EU 5 110 5 6 110 4.5 EU CA 3 CA EU 6 110 6 7 110 5.0 EU CA 3 1 CA EU 7 110 7 8 110 6.0 EU CA 3 2 CA EU 8 110 8 9 110 6.5 EU CA 6 CA EU 9 110 9 10 110 7.0 EU CA 6 1 CA EU 10 110 10 11 110 8.0 EU CA 6 2 CA EU 11 110 11 12 110 8.5 EU CA 6 3 CA EU 12 110 12 13 110 9.5 EU CA 3 6 1 CA EU 13 110 13 14 110 10.0 EU CA 3 6 2 CA EU 14 110 14 15 110 10.5 EU CA 6 6 CA EU 15 110 15 16 106 11.5 EU CA 6 6 1 CA EU 16 110 16 17 94 12.0 EU CA 6 6 2 CA EU 17 110 17 18 82 13.0 EU CA 6 6 3 CA EU 18 110 18 19 70 13.5 EU CA 1 6 6 3 CA EU 19 110 19 20 52 14.5 EU CA 2 6 6 3 CA EU 20 90 20 0 - MOD 110 WLL 55t - MOD 110 WLL 55t 6.0m 3.0m 2.0m 1.0m MOD 250/110 CONE ADAPTER 85t SHACKLE 55t SHACKLE MOD 250: M24x80 HT BOLTS, NUTS & WASHERS MOD 110: M20x65 HT BOLTS, NUTS & WASHERS Mod 250/110 - SYSTEM Specification Rated at 110 tonnes at 15m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 55 tonnes (110 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 37
MOD 250/70H: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 250/70H has an assemled span ranging from 1 metre to 20 metres in 0.5 metre increments. β = Sling to Vertical angle - 1 0 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 1 100 0.8 EU EU 1 100 1 2 100 1.5 EU CA CA EU 2 100 2 3 100 2.5 EU CA 1 CA EU 3 100 3 4 100 3.0 EU CA 2 CA EU 4 100 4 5 100 3.5 EU CA 3 CA EU 5 100 5 6 100 4.5 EU CA 3 1 CA EU 6 100 6 7 100 5.0 EU CA 3 2 CA EU 7 100 7 8 100 6.0 EU CA 6 CA EU 8 100 8 9 100 6.5 EU CA 6 1 CA EU 9 100 9 10 100 7.0 EU CA 6 2 CA EU 10 100 10 11 100 8.0 EU CA 6 3 CA EU 11 100 11 12 100 8.5 EU CA 3 6 1 CA EU 12 100 12 13 100 9.5 EU CA 3 6 2 CA EU 13 100 13 14 100 10.0 EU CA 6 6 CA EU 14 100 14 15 100 10.5 EU CA 6 6 1 CA EU 15 100 15 16 100 11.5 EU CA 6 6 2 CA EU 16 100 16 17 94 12.0 EU CA 6 6 3 CA EU 17 100 17 18 82 13.0 EU CA 1 6 6 3 CA EU 18 100 18 19 70 13.5 EU CA 2 6 6 3 CA EU 19 100 19 20 52 14.5 EU CA 2 6 6 3 CA EU 20 90 20 0 - MOD 70H WLL 50t - MOD 70H WLL 50t 6.0m 3.0m 2.0m 1.0m MOD 250/70 CONE ADAPTER 85t SHACKLE 55t SHACKLE MOD 250: M24x80 HT BOLTS, NUTS & WASHERS MOD 70H: M20x65 HT BOLTS, NUTS & WASHERS Mod 250/70H - SYSTEM Specification Rated at 100 tonnes at 16m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 50 tonnes (100 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 38
MOD 250/70: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 250/70 has an assemled span ranging from 1 metre to 20 metres in 0.5 metre increments. β = Sling to Vertical angle - 1 0 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 1 70 0.8 EU EU 1 70 1 2 70 1.5 EU CA CA EU 2 70 2 3 70 2.5 EU CA 1 CA EU 3 70 3 4 70 3.0 EU CA 2 CA EU 4 70 4 5 70 3.5 EU CA 3 CA EU 5 70 5 6 70 4.5 EU CA 3 1 CA EU 6 70 6 7 70 5.0 EU CA 3 2 CA EU 7 70 7 8 70 6.0 EU CA 6 CA EU 8 70 8 9 70 6.5 EU CA 6 1 CA EU 9 70 9 10 70 7.0 EU CA 6 2 CA EU 10 70 10 11 70 8.0 EU CA 6 3 CA EU 11 70 11 12 70 8.5 EU CA 3 6 1 CA EU 12 70 12 13 70 9.5 EU CA 3 6 2 CA EU 13 70 13 14 70 10.0 EU CA 6 6 CA EU 14 70 14 15 70 10.5 EU CA 6 6 1 CA EU 15 70 15 16 70 11.5 EU CA 6 6 2 CA EU 16 70 16 17 70 12.0 EU CA 6 6 3 CA EU 17 70 17 18 70 13.0 EU CA 1 6 6 3 CA EU 18 70 18 19 70 13.5 EU CA 2 6 6 3 CA EU 19 70 19 20 52 14.5 EU CA 2 6 6 3 CA EU 20 70 20 0 - MOD 70 WLL 35t - MOD 70 WLL 35t 6.0m 3.0m 2.0m 1.0m MOD 250/70 CONE ADAPTER 55t SHACKLE 35t SHACKLE MOD 250: M24x80 HT BOLTS, NUTS & WASHERS MOD 70H M20x65 HT BOLTS, NUTS & WASHERS Mod 250/70 - SYSTEM Specification Rated at 70 tonnes at 19m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 35 tonnes (70 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 39
MOD 400/400 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 400/400 has an assemled span ranging from 2 metres to 23m in 1m increments. β = Sling to Vertical angle WLL 200t - WLL 200t 6m 3m 2m 1m 0 Fig. 1: Typical Spreader Assemly. 0.5m 300t WIDE BODY SHACKLE 200t WIDE BODY SHACKLE 0 M24X90 GRADE 8.8, HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 400 1.5 EU EU 2 400 2 3 400 2.5 EU 1 EU 3 400 3 4 400 3.0 EU 2 EU 4 400 4 5 400 3.5 EU 3 EU 5 400 5 6 400 4.5 EU 3 1 EU 6 400 6 7 400 5.0 EU 3 2 EU 7 400 7 8 400 6.0 EU 6 EU 8 400 8 9 400 6.5 EU 6 1 EU 9 400 9 10 384 7.0 EU 6 2 EU 10 400 10 11 365 8.0 EU 6 3 EU 11 400 11 12 350 8.5 EU 3 6 1 EU 12 400 12 13 327 9.5 EU 3 6 2 EU 13 400 13 14 303 10.0 EU 6 6 EU 14 400 14 15 278 11.0 EU 6 6 1 EU 15 400 15 16 250 11.5 EU 6 6 2 EU 16 400 16 17 227 12.0 EU 6 6 3 EU 17 393 17 18 205 13.0 EU 1 6 6 3 EU 18 355 18 19 183 13.5 EU 2 6 6 3 EU 19 317 19 20 161 14.5 EU 6 6 6 EU 20 279 20 21 145 15.0 EU 6 6 6 1 EU 21 251 21 22 133 16.0 EU 6 6 6 2 EU 22 230 22 23 116 16.5 EU 6 6 6 3 EU 23 200 23 Mod 400/400 - SYSTEM Specification Rated at 400 tonnes at 16m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 200 tonnes (400 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 40
MOD 400/500 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 400/500 has an assemled span ranging from 2 metres to 23m in 1m increments. β = Sling to Vertical angle WLL 250t - WLL 250t 6m 3m 2m 1m 0 Fig. 1: Typical Spreader Assemly. 0.5m 300t WIDE BODY SHACKLE 250t WIDE BODY SHACKLE 0 M24X90 GRADE 8.8, HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 420 1.5 EU EU 2 500 2 3 420 2.5 EU 1 EU 3 500 3 4 420 3.0 EU 2 EU 4 500 4 5 420 3.5 EU 3 EU 5 500 5 6 420 4.5 EU 3 1 EU 6 500 6 7 420 5.0 EU 3 2 EU 7 500 7 8 413 6.0 EU 6 EU 8 500 8 9 400 6.5 EU 6 1 EU 9 500 9 10 384 7.0 EU 6 2 EU 10 500 10 11 365 8.0 EU 6 3 EU 11 500 11 12 350 8.5 EU 3 6 1 EU 12 500 12 13 327 9.5 EU 3 6 2 EU 13 500 13 14 303 10.0 EU 6 6 EU 14 500 14 15 278 11.0 EU 6 6 1 EU 15 481 15 16 250 11.5 EU 6 6 2 EU 16 433 16 17 227 12.0 EU 6 6 3 EU 17 393 17 18 205 13.0 EU 1 6 6 3 EU 18 355 18 19 183 13.5 EU 2 6 6 3 EU 19 317 19 20 161 14.5 EU 6 6 6 EU 20 279 20 21 145 15.0 EU 6 6 6 1 EU 21 251 21 22 133 16.0 EU 6 6 6 2 EU 22 230 22 23 116 16.5 EU 6 6 6 3 EU 23 200 23 Mod 400/500 - SYSTEM Specification Rated at 500 tonnes at 14m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 250 tonnes (500 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 41
MOD 400/600 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 400/600 has an assemled span ranging from 2 metres to 23m in 1m increments. β = Sling to Vertical angle WLL 300t - WLL 300t 6m 3m 2m 1m 0 Fig. 1: Typical Spreader Assemly. 0.5m 400t WIDE BODY SHACKLE 300t WIDE BODY SHACKLE 0 M24X90 GRADE 8.8, HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 460 1.5 EU EU 2 600 2 3 456 2.5 EU 1 EU 3 600 3 4 450 3.0 EU 2 EU 4 600 4 5 442 3.5 EU 3 EU 5 600 5 6 434 4.5 EU 3 1 EU 6 600 6 7 424 5.0 EU 3 2 EU 7 600 7 8 413 6.0 EU 6 EU 8 600 8 9 400 6.5 EU 6 1 EU 9 600 9 10 384 7.0 EU 6 2 EU 10 600 10 11 365 8.0 EU 6 3 EU 11 600 11 12 350 8.5 EU 3 6 1 EU 12 600 12 13 327 9.5 EU 3 6 2 EU 13 566 13 14 303 10.0 EU 6 6 EU 14 524 14 15 278 11.0 EU 6 6 1 EU 15 481 15 16 250 11.5 EU 6 6 2 EU 16 433 16 17 227 12.0 EU 6 6 3 EU 17 393 17 18 205 13.0 EU 1 6 6 3 EU 18 355 18 19 183 13.5 EU 2 6 6 3 EU 19 317 19 20 161 14.5 EU 6 6 6 EU 20 279 20 21 145 15.0 EU 6 6 6 1 EU 21 251 21 22 133 16.0 EU 6 6 6 2 EU 22 230 22 23 116 16.5 EU 6 6 6 3 EU 23 200 23 Mod 400/600 - SYSTEM Specification Rated at 600 tonnes at 12m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 300 tonnes (600 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 42
MOD 400/250: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 400/250 has an assemled span ranging from 2 metres to 23 metres in 1 metre increments. β = Sling to Vertical angle 1-0 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 2 250 1.5 EU EU 2 250 2 3 250 2.5 EU CA CA EU 3 250 3 4 230 3.0 EU CA 1 CA EU 4 230 4 5 250 3.5 EU CA 2 CA EU 5 250 5 6 250 4.5 EU CA 3 CA EU 6 250 6 7 250 5.0 EU CA 3 1 CA EU 7 250 7 8 250 6.0 EU CA 3 2 CA EU 8 250 8 9 230 6.5 EU CA 6 CA EU 9 230 9 10 250 7.0 EU CA 6 1 CA EU 10 250 10 11 250 8.0 EU CA 6 2 CA EU 11 250 11 12 250 8.5 EU CA 6 3 CA EU 12 250 12 13 250 9.5 EU CA 3 6 1 CA EU 13 250 13 14 230 10.0 EU CA 3 6 2 CA EU 14 230 14 15 250 11.0 EU CA 6 6 CA EU 15 250 15 16 250 11.5 EU CA 6 6 1 CA EU 16 250 16 17 227 12.0 EU CA 6 6 2 CA EU 17 250 17 18 205 13.0 EU CA 6 6 3 CA EU 18 230 18 19 183 13.5 EU CA 3 6 6 1 CA EU 19 250 19 20 161 14.5 EU CA 3 6 6 2 CA EU 20 250 20 21 145 15.0 EU CA 6 6 6 CA EU 21 250 21 22 133 16.0 EU CA 6 6 6 1 CA EU 22 230 22 23 116 16.5 EU CA 6 6 6 2 CA EU 23 200 23 0 - MOD 250 WLL 125t - MOD 250 WLL 125t 6.0m 3.0m 2.0m 1.0m MOD 400/250 CONE ADAPTER 200t WIDE BODY SHACKLE 125t WIDE BODY SHACKLE MOD 400: M24x90 HT BOLTS, MOD 250: M24x80 HT BOLTS, Mod 400/250 - SYSTEM Specification Rated at 12 tonnes at 10.5m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 6 tonnes (12 tonnes comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 43
MOD 400/110SH: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 400/110SH has an assemled span ranging from 2 metres to 23 metres in 1 metre increments. β = Sling to Vertical angle - 0 1 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 2 240 1.5 EU EU 2 240 2 3 240 2.5 EU CA CA EU 3 240 3 4 240 3.0 EU CA 1 CA EU 4 240 4 5 240 3.5 EU CA 2 CA EU 5 240 5 6 240 4.5 EU CA 3 CA EU 6 240 6 7 240 5.0 EU CA 3 1 CA EU 7 240 7 8 240 6.0 EU CA 3 2 CA EU 8 240 8 9 240 6.5 EU CA 6 CA EU 9 240 9 10 240 7.0 EU CA 6 1 CA EU 10 240 10 11 240 8.0 EU CA 6 2 CA EU 11 240 11 12 240 8.5 EU CA 6 3 CA EU 12 240 12 13 240 9.5 EU CA 3 6 1 CA EU 13 240 13 14 240 10.0 EU CA 3 6 2 CA EU 14 240 14 15 240 11.0 EU CA 6 6 CA EU 15 240 15 16 240 11.5 EU CA 6 6 1 CA EU 16 240 16 17 227 12.0 EU CA 6 6 2 CA EU 17 240 17 18 205 13.0 EU CA 6 6 3 CA EU 18 240 18 19 183 13.5 EU CA 3 6 6 1 CA EU 19 240 19 20 161 14.5 EU CA 3 6 6 2 CA EU 20 240 20 21 145 15.0 EU CA 6 6 6 CA EU 21 240 21 22 133 16.0 EU CA 6 6 6 1 CA EU 22 230 22 23 116 16.5 EU CA 6 6 6 2 CA EU 23 200 23 0 - MOD 110SH WLL 120t - MOD 110SH WLL 120t 6.0m 3.0m 2.0m 1.0m MOD 400/110 CONE ADAPTER 150t SHACKLE 120t SHACKLE MOD 400: M24x90 HT BOLTS, MOD 110: M20x65 HT BOLTS, Mod 400/110SH - SYSTEM Specification Rated at 240 tonnes at 21m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 120 tonnes (240 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 44
MOD 400/110H: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 400/110H has an assemled span ranging from 2 metres to 23 metres in 1 metre increments. β = Sling to Vertical angle - 0 1 Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 2 240 1.5 EU EU 2 240 2 3 240 2.5 EU CA CA EU 3 240 3 4 240 3.0 EU CA 1 CA EU 4 240 4 5 240 3.5 EU CA 2 CA EU 5 240 5 6 240 4.5 EU CA 3 CA EU 6 240 6 7 240 5.0 EU CA 3 1 CA EU 7 240 7 8 240 6.0 EU CA 3 2 CA EU 8 240 8 9 240 6.5 EU CA 6 CA EU 9 240 9 10 240 7.0 EU CA 6 1 CA EU 10 240 10 11 240 8.0 EU CA 6 2 CA EU 11 240 11 12 240 8.5 EU CA 6 3 CA EU 12 240 12 13 240 9.5 EU CA 3 6 1 CA EU 13 240 13 14 240 10.0 EU CA 3 6 2 CA EU 14 240 14 15 240 11.0 EU CA 6 6 CA EU 15 240 15 16 240 11.5 EU CA 6 6 1 CA EU 16 240 16 17 227 12.0 EU CA 6 6 2 CA EU 17 240 17 18 205 13.0 EU CA 6 6 3 CA EU 18 240 18 19 183 13.5 EU CA 3 6 6 1 CA EU 19 240 19 20 161 14.5 EU CA 3 6 6 2 CA EU 20 240 20 21 145 15.0 EU CA 6 6 6 CA EU 21 240 21 22 133 16.0 EU CA 6 6 6 1 CA EU 22 230 22 23 116 16.5 EU CA 6 6 6 2 CA EU 23 200 23 0 - MOD 110H WLL 120t - MOD 110H WLL 120t 6.0m 3.0m 2.0m 1.0m MOD 400/110 CONE ADAPTER 150t SHACKLE 120t SHACKLE MOD 400: M24x90 HT BOLTS, MOD 110: M20x65 HT BOLTS, Mod 400/110H - SYSTEM Specification Rated at 240 tonnes at 21m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 120 tonnes (240 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 45
MOD 400/110: Hyrid The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e assemled to achieve different spans. The Modulift 400/110 has an assemled span ranging from 2 metres to 23 metres in 0.5 metre increments. β = Sling to Vertical angle - 0 1 Fig.1: Typical Spreader Assemly. Fig.1: Typical Spreader Assemly. CONE ADAPTER Load v /m 45º Recommended Configuration. EU - End Unit (1m) CA - Cone Adaptor (0.5m) 30º 2 110 1.5 EU EU 2 110 2 3 110 2.5 EU CA CA EU 3 110 3 4 110 3.0 EU CA 1 CA EU 4 110 4 5 110 3.5 EU CA 2 CA EU 5 110 5 6 110 4.5 EU CA 3 CA EU 6 110 6 7 110 5.0 EU CA 3 1 CA EU 7 110 7 8 110 6.0 EU CA 3 2 CA EU 8 110 8 9 110 6.5 EU CA 6 CA EU 9 110 9 10 110 7.0 EU CA 6 1 CA EU 10 110 10 11 110 8.0 EU CA 6 2 CA EU 11 110 11 12 110 8.5 EU CA 6 3 CA EU 12 110 12 13 110 9.5 EU CA 3 6 1 CA EU 13 110 13 14 110 10.0 EU CA 3 6 2 CA EU 14 110 14 15 110 11.0 EU CA 6 6 CA EU 15 110 15 16 110 11.5 EU CA 6 6 1 CA EU 16 110 16 17 110 12.0 EU CA 6 6 2 CA EU 17 110 17 18 110 13.0 EU CA 6 6 3 CA EU 18 110 18 19 110 13.5 EU CA 3 6 6 1 CA EU 19 110 19 20 110 14.5 EU CA 3 6 6 2 CA EU 20 110 20 21 110 15.0 EU CA 6 6 6 CA EU 21 110 21 22 110 16.0 EU CA 6 6 6 1 CA EU 22 110 22 23 110 16.5 EU CA 6 6 6 2 CA EU 23 110 23 0 1 - MOD 110H WLL 55t - MOD 110H WLL 55t 6.0m 3.0m 2.0m 1.0m 0.5m MOD 400/110 CONE ADAPTER 85t SHACKLE 55t SHACKLE MOD 400: M24x90 HT BOLTS, MOD 110: M20x65 HT BOLTS, Mod 400/110 - SYSTEM Specification Rated at 110 tonnes at 23m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 55 tonnes (110 tonnes comined capacity) Bolt tightening torque: 250Nm (M24) 150Nm (M20) ner size required: 36mm (M24) 30mm (M20) 46
MOD 600XB/400 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 600XB/400 has an assemled span ranging from 2 metres to 26m in 1m increments. WLL 200t - β = Sling to Vertical angle 0 WLL 200t 5m 3m 4m 3m 1 2 Fig. 1: Typical Spreader Assemly. 2m 1m 0.5m 0 1 2 300t WIDE BODY SHACKLE 200t WIDE BODY SHACKLE M24x90 GRADE 10.9 HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 285 1.0 EU EU 2 400 2 3 285 2.0 EU 1 EU 3 400 3 4 285 2.5 EU 2 EU 4 400 4 5 285 3.5 EU 3 EU 5 400 5 6 285 4.0 EU 3 1 EU 6 400 6 7 285 4.5 EU 3 2 EU 7 400 7 8 285 5.5 EU 6 EU 8 400 8 9 285 6.0 EU 6 1 EU 9 400 9 10 285 7.0 EU 6 2 EU 10 400 10 11 285 7.5 EU 6 3 EU 11 400 11 12 285 8.5 EU 3 6 1 EU 12 400 12 13 285 9.0 EU 3 6 2 EU 13 400 13 14 285 9.5 EU 6 6 EU 14 400 14 15 285 10.5 EU 6 6 1 EU 15 400 15 16 285 11.0 EU 6 6 2 EU 16 400 16 17 285 12.0 EU 6 6 3 EU 17 400 17 18 285 12.5 EU 1 6 6 3 EU 18 400 18 19 285 13.0 EU 2 6 6 3 EU 19 400 19 20 285 14.0 EU 6 6 6 EU 20 400 20 21 285 14.5 EU 6 6 6 1 EU 21 400 21 22 285 15.0 EU 6 6 6 2 EU 22 400 22 23 285 15.5 EU 6 6 6 3 EU 23 400 23 24 260 17.0 EU 1 6 6 6 3 EU 24 400 24 25 234 17.5 EU 2 6 6 6 3 EU 25 400 25 26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26 Mod 600XB/400 - SYSTEM Specification Rated at 400 tonnes at 25m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 200 tonnes (400 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 47
MOD 600XB/600 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 600XB/600 has an assemled span ranging from 2 metres to 26m in 1m increments. WLL 300t - β = Sling to Vertical angle 0 WLL 300t 5m 3m 4m 3m 1 2 Fig. 1: Typical Spreader Assemly. 2m 1m 0.5m 0 1 400t WIDE BODY SHACKLE 300t WIDE BODY SHACKLE 2 M24x90 GRADE 10.9 HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 415 1.0 EU EU 2 600 2 3 415 2.0 EU 1 EU 3 600 3 4 415 2.5 EU 2 EU 4 600 4 5 415 3.5 EU 3 EU 5 600 5 6 415 4.0 EU 3 1 EU 6 600 6 7 415 4.5 EU 3 2 EU 7 600 7 8 415 5.5 EU 6 EU 8 600 8 9 415 6.0 EU 6 1 EU 9 600 9 10 415 7.0 EU 6 2 EU 10 600 10 11 415 7.5 EU 6 3 EU 11 600 11 12 415 8.5 EU 3 6 1 EU 12 600 12 13 415 9.0 EU 3 6 2 EU 13 600 13 14 415 9.5 EU 6 6 EU 14 600 14 15 415 10.5 EU 6 6 1 EU 15 600 15 16 415 11.0 EU 6 6 2 EU 16 600 16 17 415 12.0 EU 6 6 3 EU 17 600 17 18 415 12.5 EU 1 6 6 3 EU 18 600 18 19 415 13.0 EU 2 6 6 3 EU 19 600 19 20 391 14.0 EU 6 6 6 EU 20 600 20 21 354 14.5 EU 6 6 6 1 EU 21 600 21 22 320 15.0 EU 6 6 6 2 EU 22 565 22 23 289 15.5 EU 6 6 6 3 EU 23 512 23 24 260 17.0 EU 1 6 6 6 3 EU 24 461 24 25 234 17.5 EU 2 6 6 6 3 EU 25 416 25 26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26 Mod 600XB/600 - SYSTEM Specification Rated at 600 tonnes at 21m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 300 tonnes (600 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 48
MOD 600XB/800 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 600XB/800 has an assemled span ranging from 2 metres to 26m in 1m increments. WLL 400t - β = Sling to Vertical angle 0 WLL 400t 6m 5m 4m 3m 1 2 Fig. 1: Typical Spreader Assemly. 2m 1m 0.5m 0 1 500t WIDE BODY SHACKLE 400t WIDE BODY SHACKLE 2 M24x90 GRADE 10.9 HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 565 1.0 EU EU 2 800 2 3 565 2.0 EU 1 EU 3 800 3 4 565 2.5 EU 2 EU 4 800 4 5 565 3.5 EU 3 EU 5 800 5 6 565 4.0 EU 3 1 EU 6 800 6 7 565 4.5 EU 3 2 EU 7 800 7 8 565 5.5 EU 6 EU 8 800 8 9 565 6.0 EU 6 1 EU 9 800 9 10 565 7.0 EU 6 2 EU 10 800 10 11 565 7.5 EU 6 3 EU 11 800 11 12 565 8.5 EU 3 6 1 EU 12 800 12 13 565 9.0 EU 3 6 2 EU 13 800 13 14 565 9.5 EU 6 6 EU 14 800 14 15 565 10.5 EU 6 6 1 EU 15 800 15 16 559 11.0 EU 6 6 2 EU 16 800 16 17 514 12.0 EU 6 6 3 EU 17 800 17 18 469 12.5 EU 1 6 6 3 EU 18 800 18 19 427 13.0 EU 2 6 6 3 EU 19 749 19 20 391 14.0 EU 6 6 6 EU 20 688 20 21 354 14.5 EU 6 6 6 1 EU 21 623 21 22 320 15.5 EU 6 6 6 2 EU 22 565 22 23 289 16.0 EU 6 6 6 3 EU 23 512 23 24 260 17.0 EU 1 6 6 6 3 EU 24 461 24 25 234 17.5 EU 2 6 6 6 3 EU 25 416 25 26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26 Mod 600XB/800 - SYSTEM Specification Rated at 800 tonnes at 18m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 400 tonnes (800 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 49
MOD 600XB/1000 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 600XB/1000 has an assemled span ranging from 2 metres to 26m in 1m increments. WLL 500t - β = Sling to Vertical angle 0 WLL 500t 6m 5m 4m 3m 1 2 Fig. 1: Typical Spreader Assemly. 2m 1m 0.5m 0 1 600t WIDE BODY SHACKLE 500t WIDE BODY SHACKLE 2 M24x90 GRADE 10.9 HT BOLTS, Load v /m 45 Recommended Configuration EU - End Unit (1m) = SLING TO VERTICAL ANGLE, ß 30 2 575 1.0 EU EU 2 1000 2 3 575 2.0 EU 1 EU 3 1000 3 4 575 2.5 EU 2 EU 4 1000 4 5 575 3.5 EU 3 EU 5 1000 5 6 575 4.0 EU 3 1 EU 6 1000 6 7 575 4.5 EU 3 2 EU 7 1000 7 8 575 5.5 EU 6 EU 8 1000 8 9 575 6.0 EU 6 1 EU 9 1000 9 10 575 7.0 EU 6 2 EU 10 1000 10 11 575 7.5 EU 6 3 EU 11 1000 11 12 575 8.5 EU 3 6 1 EU 12 1000 12 13 575 9.0 EU 3 6 2 EU 13 1000 13 14 575 9.5 EU 6 6 EU 14 1000 14 15 575 10.5 EU 6 6 1 EU 15 1000 15 16 559 11.0 EU 6 6 2 EU 16 977 16 17 514 12.0 EU 6 6 3 EU 17 899 17 18 469 12.5 EU 1 6 6 3 EU 18 821 18 19 427 13.0 EU 2 6 6 3 EU 19 749 19 Mod 600XB/1000 - SYSTEM Specification Rated at 1000 tonnes at 15m span Sling to Vertical angle, ß, 45 degrees End units and drop links are rated at 500 tonnes (1000 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 20 391 14.0 EU 6 6 6 EU 20 688 20 21 354 14.5 EU 6 6 6 1 EU 21 623 21 22 320 15.5 EU 6 6 6 2 EU 22 565 22 23 289 16.0 EU 6 6 6 3 EU 23 512 23 24 260 17.0 EU 1 6 6 6 3 EU 24 461 24 25 234 17.5 EU 2 6 6 6 3 EU 25 416 25 26 209 18.0 EU 1 2 6 6 6 3 EU 26 373 26 50
MOD 800J/1000 The Modulift Spreader is modular in length. Every spreader consists of 1 pair of End Units & Drop Links, with intermediate struts that can e olted into the assemly to achieve different spans. The MOD 800J/1000 has an assemled span ranging from 2 metres to 28m in 0.5m increments. β = Sling to Vertical angle Fig. 1: Typical Spreader Assemly. Load v Recommended Configuration. EU - End Unit (1m) = SLING to VERTICAL ANGLE, β 30º EU EU 2 1000 1.5 EU 1 EU 3 1000 2.5 EU 2 EU 4 1000 3.5 EU 3 EU 5 1000 4.5 EU 3 1 EU 6 1000 5.5 EU 3 2 EU 7 1000 6.5 EU 6 EU 8 1000 7.5 EU 6 1 EU 9 1000 8.5 EU 6 2 EU 10 1000 9.5 EU 6 3 EU 11 1000 10.5 EU 3 6 1 EU 12 1000 11.5 EU 3 6 2 EU 13 1000 12.5 EU 6 6 EU 14 1000 13.5 EU 6 6 1 EU 15 1000 14.5 EU 6 6 2 EU 16 1000 15.5 EU 6 6 3 EU 17 1000 16.5 EU 1 6 6 3 EU 18 1000 17.5 EU 2 6 6 3 EU 19 1000 18.5 EU 6 6 6 EU 20 1000 19.5 EU 6 6 6 1 EU 21 944 20.5 EU 6 6 6 2 EU 22 871 21.5 EU 6 6 6 3 EU 23 802 22.5 EU 1 6 6 6 3 EU 24 734 23.5 EU 2 6 6 6 3 EU 25 673 24.5 EU 1 2 6 6 6 3 EU 26 612 25.5 EU 1 3 6 6 6 3 EU 27 556 26.5 EU 2 3 6 6 6 3 EU 28 505 27.5 0 1 2 - WLL 500t - WLL 500t 6.0m 5.0m 4.0m 3.0m 2.0m 1.0m 0.5m 600t WIDE BODY SHACKLE 500t WIDE BODY SHACKJLE M24x100 Grade 10.9 HT BOLTS, Mod 800J/1000 - SYSTEM Specification Rated at 1000 tonnes at 20m span Sling to Vertical angle, ß, 30 degrees End units and drop links are rated at 500 tonnes (1000 tonnes comined capacity) Bolt tightening torque: 250Nm ner size required: 36mm 51
CMOD Spreader Frame Range Modulift Modular Spreader Frames work with existing struts from our Modular Spreader Beam range Fig. 1: Example CMOD Modular Spreader Frame Modulift, the market leaders in Spreader Beam design and manufacture, have extended their modular offering, y launching the CMOD Modular Spreader Frame! A truly adaptale frame that maintains its engineering principles as its configuration adapts. Designed with ease and economy in mind - the CMOD is simple to set up, manoeuvre, and reconfigure to any size frame - allowing for multiple uses and diverse application. The CMOD is a modular frame utilising Corner Units which are compatile with our existing Spreader Beam Struts and is modular in length and width. Every CMOD Spreader Frame consists of 4 x Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. Existing customers can adapt their Spreader Beam into a frame, y simply olting on the corresponding Corner Units and any additional Struts required. Even the largest CMOD can e easily transported as the frame is roken down into modular parts, saving the cost of specialist transportation. System Specifications The CMOD comes in the following sizes: CMOD 6, CMOD 12, CMOD 24, CMOD 34, CMOD 50, CMOD 70 and CMOD 110 It spans from 0.5m/1 6 x 0.5m/1 6 to 16m/52 x 16m/52, whilst adapting to all rectangular shapes in etween. The systems will lift up to 140t* * The system s will de-rate as the shape of the frame ecomes more rectangular. Higher capacities and longer spans in development. 52
CMOD 6 Spreader Frame The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. The CMOD 6 has an assemled span ranging from 0.5m y 0.5m to 2.5m y 2.5m and all spans inetween. β Fig. 1 Typical CMOD Spreader Frame Assemly β = Sling to Vertical Angle () - Assemled Frame: CORNER UNIT Tale 2 30 = tonnes 2.5 8 2 8 8 m 1.5 8 8 8 /m /m 1 8 8 8 6 0.5 8 8 8 6 6 0.5 1 1.5 2 2.5 /m m 2.5 45 = tonnes 6 2 6 6 1.5 6 6 6 1 6 6 6 4 0.5 6 6 6 4 4 0.5 1 1.5 2 2.5 /m CORNER UNIT - Length: 0.25m each 1000mm 600mm 300mm 200mm 100mm 8.5t SHACKLE 6.5t SHACKLE M10X30, GRADE 8.8, HT BOLTS NUTS & WASHERS CMOD 6 - SYSTEM Specification Rated at a maximum of 8 tonnes Sling to Vertical angle, ß, no more than 45 degrees Corner Units are rated at 2 tonnes each (8t comined capacity) Bolt tightening torque: 60Nm ner size required: 17mm 53
CMOD 12 Spreader Frame The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. The CMOD 12 has an assemled span ranging from 0.5m y 0.5m to 4m y 4m and all spans inetween. β Fig. 1 Typical CMOD Spreader Frame Assemly β = Sling to Vertical Angle () - Assemled Frame: CORNER UNIT Tale 2 /m 4 30 = tonnes 16 3.5 16 16 3 16 16 15 2.5 16 16 15 14 CORNER UNIT - Length: 0.25m each 1.5m 1.0m 0.75m 2 16 16 16 14 13 0.5m 1.5 16 16 16 16 14 12 0.25m 1 16 16 16 16 16 14 12 0.5 16 16 16 16 16 16 14 12 0.5 1 1.5 2 2.5 3 3.5 4 8.5t SHACKLE 6.5t SHACKLE M12X35, GRADE 8.8, HT BOLTS /m /m 4 45 = tonnes 9 3.5 9 9 3 9 9 8 2.5 9 9 8 8 2 9 9 9 8 7 1.5 9 9 9 9 8 6 1 9 9 9 9 9 8 6 0.5 9 9 9 9 9 9 8 6 0.5 1 1.5 2 2.5 3 3.5 4 /m CMOD 12 - SYSTEM Specification Rated at a maximum of 16 tonnes Sling to Vertical Angle, β, no more than 45 degrees Corner Units are rated at 4 tonnes each (16t comined capacity) Bolt tightening torque: 90Nm ner size required: 19mm 54
CMOD 24 Spreader Frame The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. The CMOD 24 has an assemled span ranging from 1m y 1m to 6m y 6m and all spans inetween. β Fig. 1 Typical CMOD Spreader Frame Assemly β = Sling to Vertical Angle () - Assemled Frame: CORNER UNIT Tale 2 6 30 = tonnes 23 CORNER UNIT - Length: 0.5m each 5 30 21 2.0m /m 4 30 24 19 1.0m 0.5m 3 30 30 24 18 17t SHACKLE 2 30 30 30 24 17 1 30 30 30 24 22 16 12t SHACKLE M20X50, GRADE 8.8, HT BOLTS NUTS & WASHERS 1 2 3 4 5 6 /m /m 6 45 = tonnes 13 5 17 12 4 19 13 10 3 19 19 13 10 2 19 19 17 13 9 1 19 19 19 13 12 9 1 2 3 4 5 6 /m CMOD 24 - SYSTEM Specification Rated at a maximum of 30 tonnes Sling to Vertical angle, ß, no more than 45 degrees Corner Units are rated at 7.5 tonnes each (30t comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 55
CMOD 34 Spreader Frame The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. The CMOD 34 has an assemled span ranging from 1m y 1m to 8m y 8m and all spans inetween. β Fig. 1 Typical CMOD Spreader Frame Assemly β = Sling to Vertical Angle () - Tale 2 Assemled Frame: CORNER UNIT 8 30 = tonnes 24 7 32 23 CORNER UNIT - Length: 0.5m each 2.0m 6 40 31 22 1.0m 5 40 40 28 20 0.5m /m 4 40 40 34 26 19 3 40 40 40 34 24 18 2 40 40 40 40 32 23 17 25t SHACKLE 17t SHACKLE M20X50, GRADE 8.8, HT BOLTS NUTS & WASHERS 1 40 40 40 40 34 30 22 16 1 2 3 4 5 6 7 8 /m 8 45 = tonnes 13 /m 7 18 13 6 22 17 12 5 27 22 16 11 4 27 27 19 15 10 3 27 27 25 19 13 10 2 27 27 27 22 18 13 9 1 27 27 27 27 19 17 12 9 1 2 3 4 5 6 7 8 /m CMOD 34 - SYSTEM Specification Rated at a maximum of 40 tonnes Sling to Vertical angle, ß, no more than 45 degrees Corner Units are rated at 10 tonnes each (40t comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 56
CMOD 50 Spreader Frame The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. The CMOD 50 has an assemled span ranging from 1m y 1m to 11m y 11m and all spans inetween. β Fig. 1 Typical CMOD Spreader Frame Assemly β = Sling to Vertical Angle () - Tale 2 /m 11 30 = tonnes 32 10 41 31 9 50 39 29 8 50 48 37 28 7 60 50 45 35 27 6 60 60 50 43 33 26 5 60 60 60 50 40 32 25 4 60 60 60 50 49 38 31 24 3 60 60 60 60 50 47 37 30 23 2 60 60 60 60 60 50 45 36 29 23 1 60 60 60 60 60 60 50 44 35 28 22 1 2 3 4 5 6 7 8 9 10 11 Assemled Frame: CORNER UNIT CORNER UNIT - Length: 0.5m each 4.0m 2.0m 1.0m 0.5m 35t SHACKLE 25t SHACKLE M20X65, GRADE 8.8, HT BOLTS /m /m 11 45 = tonnes 18 10 23 17 9 28 21 16 8 28 27 20 15 7 34 28 25 19 14 6 40 34 28 24 18 14 5 40 40 34 28 23 17 13 4 50 40 40 28 28 21 17 13 3 50 50 40 40 28 26 21 16 12 2 50 50 50 40 34 28 25 20 16 12 1 50 50 50 50 40 34 28 25 20 15 12 1 2 3 4 5 6 7 8 9 10 11 /m CMOD 50 - SYSTEM Specification Rated at a maximum of 60 tonnes Sling to Vertical angle, ß, no more than 45 degrees Corner Units are rated at 15 tonnes each (60t comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 57
CMOD 70 Spreader Frame The CMOD Spreader Frame is modular in span, and every frame consists of 4 Corner Units, with intermediate Struts that can e olted into the assemly to achieve different spans. The CMOD 70 has an assemled span ranging from 1m y 1m to 12m y 12m and all spans inetween. β Fig. 1 Typical CMOD Spreader Frame Assemly β = Sling to Vertical Angle () - Tale 2 Assemled Frame: CORNER UNIT /m 12 30 = tonnes 63 11 70 60 10 80 70 58 9 80 80 70 55 8 80 80 80 67 53 7 80 80 80 70 65 51 6 80 80 80 70 60 62 49 5 80 80 80 80 70 60 60 47 4 80 80 80 80 80 70 60 58 46 3 80 80 80 80 80 80 70 60 56 45 CORNER UNIT - Length: 0.5m each 4.0m 2.0m 1.0m 0.5m 42.5t SHACKLE 35t SHACKLE 2 80 80 80 80 80 80 70 70 60 55 44 1 80 80 80 80 80 80 80 70 70 60 54 44 1 2 3 4 5 6 7 8 9 10 11 12 M20X65, GRADE 8.8, HT BOLTS NUTS & WASHERS /m /m 12 45 = tonnes 36 11 40 34 10 40 40 33 9 46 40 40 31 8 57 46 40 38 30 7 60 57 46 40 37 29 6 60 60 57 40 34 35 28 5 60 60 60 50 40 34 34 27 4 60 60 60 60 50 40 34 33 26 3 60 60 60 60 60 50 40 34 32 26 2 60 60 60 60 60 60 50 40 34 31 25 1 60 60 60 60 60 60 60 50 40 34 31 24 1 2 3 4 5 6 7 8 9 10 11 12 /m CMOD 70 - SYSTEM Specification Rated at a maximum of 80 tonnes Sling to Vertical angle, ß, no more than 45 degrees Corner Units are rated at 20 tonnes each (80t comined capacity) Bolt tightening torque: 150Nm ner size required: 30mm 58
CMOD & Beyond System Benefits Cheaper and easier to transport than a fixed system Easy to set up, handle and manoeuvre Re-configure the frame to any size to allow for multiple uses The corner plate has a ow (like the shackle). This means that a reversed Shackle can contact the plate ow to ow allowing it to easily rotate to suit any angle of and setup of frame without de-rating the Shackle Design Strengths The plate is made of high strength caron steel and is specifically designed to withstand any ending, and transfers the compression to the strut in an almost purely axial form. The system was designed to BS EN 13155 Non Fixed Lifting Load Attachments and the method of Shackle connection has een approved y Van Beest. CMOD T-pieces Elaorating on this popular concept Modulift has now developed a T-Piece to work in conjunction with the CMOD. This allows the frame to ecome a 6-point lift, (8-point,10-point and so forth on request) adding yet another dimension to your Modulift equipment. s of up to 40m x 16m and capacities of up to 200t are availale as standard. 59
Lattice Spreader Beams The Modulift Lattice System (MLS) is a light-weight modular spreader suitale for long, light loads, and has een specially developed to suit roofing sheets. Maximum spans from 6m up to 42m in 3m increments are achievale using this system. Lower support s must e attached to the frames every 2m to ensure a uniformly distriuted load. Components TYPE 1: 100KG 3m 1m TYPE 2: 137KG CROSS BAR: 7.5KG 3m FRAMES TYPE 3: 17.5 KG CONNECTION PIN SPREADER SYSTEM Specification Rated at a maximum of 3 tonnes WLL(Upto 24m ) Sling to Vertical angle, ß, 45 degrees or less Lifting points: Slings can e connected to weld eyes on ends of 1m span cross ars, or to weld eyes on underside of frames. Assemly Max. 6.5t shackle Max. 3.25t shackle Connection Pins - 2 per Cross Beam CONNECTION JOINTS - USE 4 no. CONNECTION PINS PER JOINT. TYPICAL CROSS BAR CONNECTION 60
Lattice Spreader Beam 6-24m Configuration SPREADER Configuration No. of Crosseams 6m 2 3 2 3 or 4 9m 2 1 3 2 6 12m 1 2 3 2 1 7 15m 1 2 1 3 2 1 8 18m 1 2 1 3 1 2 1 10 21m 1 2 1 1 3 1 2 1 11 24m 1 2 1 1 3 1 1 2 1 13 1 = Type 1 Frame 2 = Type 2 Frame 3 = Type 3 Frame Maximum 1.5m overhang of roofing sheet per end Lifting Points/Load Connection Points = connection point for cross ar, and/or connection point for to weld eye. 318 KG 6m Spreader: 327 KG 6m Spreader: Alternative LC =8; CB = 6 PINS LC =8; CB = 8 PINS LC = Lattice Connections CB = Cross Beams 444 KG 9m Spreader: LC =12; CB = 12 PINS 552 KG 12m Spreader: LC =16; CB = 14 PINS 661 KG 15m Spreader: 778 KG 18m Spreader: 887 KG 21m Spreader: LC =20; CB = 16 PINS LC =24; CB = 20 PINS LC =28; CB = 22 PINS 1005 KG 24m Spreader: LC =32; CB = 26 PINS Top Sling Minimum Length 6m Spreader : 2.2m 9m Spreader: 4.3m 12m Spreader: 2.2m 15m Spreader: 4.3m 18m Spreader: 6.5m 21m Spreader: 8.7m 24m Spreader: 10.8m These lengths are essential to ensure the Sling to Vertical Angle is 45 degrees. 45º 59
Lattice Spreader Beam - 27m The Modulift Lattice System (MLS) is a light-weight modular spreader suitale for long, light loads, and has een specially developed to suit roofing sheets. Maximum spans from 6m up to 42m in 3m increments are achievale using this system. Lower support s must e attached to the frames every 2m to ensure a uniformly distriuted load. Components TYPE 1: 100KG 3m 1m TYPE 2: 137KG CROSS BAR: 7.5KG 3m FRAMES TYPE 3: 17.5 KG CONNECTION PIN Assemled Lattice Spreader Beam Total weight = 1121kg Top Sling Min Length = 13m SPREADER Configuration No. of Crosseams 27m 1 2 1 1 1 3 1 1 2 1 15 1 = Type 1 Frame x 7 2 = Type 2 Frame x 2 3 = Type 3 Frame x 1 Assemly CONNECTION JOINTS - USE 4 no. CONNECTION PINS PER JOINT. Maximum 1.5m overhang of roofing sheet per end Max. 6.5t shackle Max. 3.25t shackle TYPICAL CROSS BAR CONNECTION CONNECTION PINS - 2 PER CROSS BEAM LATTICE SPREADER Specification Rated at a maximum of 2 tonnes WLL - Uniformly Distriuted Load only (Up to 27m span) Sling to Vertical angle, ß, 45 degrees Lifting points: Slings can e connected to weld eyes on ends of 1m span cross ars, or to weld eyes on underside of frames The arrangement must not e modified without Modulift s written approval 62
Lattice Spreader Beam - 30m The Modulift Lattice System (MLS) is a light-weight modular spreader suitale for long, light loads, and has een specially developed to suit roofing sheets. Maximum spans from 6m up to 42m in 3m increments are achievale using this system. Lower support s must e attached to the frames every 2m to ensure a uniformly distriuted load. Components TYPE 1: 100KG 3m 1m TYPE 2: 137KG CROSS BAR: 7.5KG 3m FRAMES TYPE 3: 17.5 KG CONNECTION PIN Assemled Lattice Spreader Beam Centred Sling Support Wire Rope Chain Block Total weight = 1231kg Top Sling Min Length = 15m Use round/weing to connect chain lock and Spreader Beam SPREADER Configuration No. of Crosseams 30m 1 2 1 1 1 3 1 1 1 2 1 16 1 = Type 1 Frame x 8 2 = Type 2 Frame x 2 3 = Type 3 Frame x 1 Assemly CONNECTION JOINTS - USE 4 no. CONNECTION PINS PER JOINT. Maximum 1.5m overhang of roofing sheet per end Max. 6.5t shackle Max. 3.25t shackle TYPICAL CROSS BAR CONNECTION CONNECTION PINS - 2 PER CROSS BEAM LATTICE SPREADER Specification Rated at a maximum of 2 tonnes WLL - Uniformly Distriuted Load only (Up to 30m span) Sling to Vertical angle, ß, 45 degrees Lifting points: Slings can e connected to weld eyes on ends of 1m span cross ars, or to weld eyes on underside of frames The arrangement must not e modified without Modulift s written approval 63
Lattice Spreader Beam - 33m The Modulift Lattice System (MLS) is a light-weight modular spreader suitale for long, light loads, and has een specially developed to suit roofing sheets. Maximum spans from 6m up to 42m in 3m increments are achievale using this system. Lower support s must e attached to the frames every 2m to ensure a uniformly distriuted load. Components TYPE 1: 100KG 3m 1m TYPE 2: 137KG CROSS BAR: 7.5KG 3m FRAMES TYPE 3: 17.5 KG CONNECTION PIN Assemled Lattice Spreader Beam Centred Sling Support Wire Rope Chain Block Total weight = 1347kg Top Sling Min Length = 17.5m Use round/weing to connect chain lock and Spreader Beam SPREADER Configuration No. of Crosseams 33m 1 2 1 1 1 1 3 1 1 1 2 1 18 1 = Type 1 Frame x 9 2 = Type 2 Frame x 2 3 = Type 3 Frame x 1 Assemly CONNECTION JOINTS - USE 4 no. CONNECTION PINS PER JOINT. Maximum 1.5m overhang of roofing sheet per end Max. 6.5t shackle Max. 3.25t shackle TYPICAL CROSS BAR CONNECTION CONNECTION PINS - 2 PER CROSS BEAM LATTICE SPREADER Specification Rated at a maximum of 2 tonnes WLL - Uniformly Distriuted Load only (Up to 33m span) Sling to Vertical angle, ß, 45 degrees Lifting points: Slings can e connected to weld eyes on ends of 1m span cross ars, or to weld eyes on underside of frames The arrangement must not e modified without Modulift s written approval 64
Lattice Spreader Beam - 36m The Modulift Lattice System (MLS) is a light-weight modular spreader suitale for long, light loads, and has een specially developed to suit roofing sheets. Maximum spans from 6m up to 42m in 3m increments are achievale using this system. Lower support s can e attached to the frames every 2m to ensure a uniformly distriuted load. Components TYPE 1: 100KG 3m 1m TYPE 2: 137KG CROSS BAR: 7.5KG 3m FRAMES TYPE 3: 17.5 KG CONNECTION PIN Assemled Lattice Spreader Beam 22m 18m 13m 18m 22m 2.6m Total weight = 1604kg Top Sling Min Length = As shown aove SPREADER Configuration No. of Crosseams 36m 2 1 2 1 1 2 3 2 1 1 2 1 2 19 1 = Type 1 Frame x 6 2 = Type 2 Frame x 6 3 = Type 3 Frame x 1 Assemly CONNECTION JOINTS - USE 4 no. CONNECTION PINS PER JOINT. Maximum 1.5m overhang of roofing sheet per end Max. 6.5t shackle Max. 3.25t shackle TYPICAL CROSS BAR CONNECTION CONNECTION PINS - 2 PER CROSS BEAM LATTICE SPREADER Specification Rated at a maximum of 2 tonnes WLL - Uniformly Distriuted Load only (Up to 36m span) Sling to Vertical angle, ß, 45 degrees Lifting points: Slings can e connected to weld eyes on ends of 1m span cross ars, or to weld eyes on underside of frames The arrangement must not e modified without Modulift s written approval 65
Lattice Spreader Beam - 42m The Modulift Lattice System (MLS) is a light-weight modular spreader suitale for long, light loads, and has een specially developed to suit roofing sheets. Maximum spans from 6m up to 42m in 3m increments are achievale using this system. Lower support s must e attached to the frames every 2m to ensure a uniformly distriuted load. TYPE 1: 100KG 3m 1m TYPE 2: 137KG CROSS BAR: 7.5KG 3m FRAMES TYPE 3: 17.5 KG CONNECTION PIN Assemled Lattice Spreader Beam 37m 33.5m 3 Leg Assy 33.5m 37m Total weight = 1822kg Top Sling Min Length = As shown aove SPREADER Configuration No. of Crosseams 42m 2 1 1 2 1 1 2 3 2 1 1 2 1 2 21 1 = Type 1 Frame x 8 2 = Type 2 Frame x 6 3 = Type 3 Frame x 1 Assemly CONNECTION JOINTS - USE 4 no. CONNECTION PINS PER JOINT. Max. 6.5t shackle Maximum 1.5m overhang of roofing sheet per end Max. 3.25t shackle TYPICAL CROSS BAR CONNECTION CONNECTION PINS - 2 PER CROSS BEAM LATTICE SPREADER Specification Rated at a maximum of 1 tonne WLL - Uniformly Distriuted Load only (Up to 42m span) Lifting points: Slings can e connected to weld eyes on ends of 1m span cross ars, or to weld eyes on underside of frames The arrangement must not e modified without Modulift s written approval. 66
Where To Buy & Contacts Modulift is here for you every step of the way... UK Head Office Contact details: Managing Director Sarah Spivey Sarah@modulift.com Technical Director Sue Caples Sue.@modulift.com QuEnSH Manager Simon Cranny Simon@modulift.com For Distriutor Operations/Training or to ecome a Distriutor International Business Development Managers Malcolm Peacock - Malcolm@modulift.com Based in UAE - Tel: +971 56 2199 663 Serafim Marinho - Serafim@modulift.com Based in Portugal - Tel: +351 93 7409 345 For Marketing Enquiries Marketing Manager - Wendy Armstrong Wendy@modulift.com Marketing Executive Sophie Briggs Sophie@modulift.com For Accounts & Order Enquiries Financial Controller Paul Savage Paul@modulift.com For Production & Administrational Enquiries Production Administrator - Lydia Davies Lydia@modulift.com Tel: +44 (0) 1202 621511 00 11 44 1202 621511 (USA & Canada) Fax: +44 (0) 1202 632811 For Sales Enquiries Sales Executive Chris Schwa Chris@modulift.com 67