Char-Lynn Power Steering No. 6-34 November, 6 Parts Information 7 Series (Gerotor Unit) 7 Series (Geroler Unit) 7 Series and 7 Series Torque Generator 00
Torque Generator Parts Drawing 700 7 Series (Gerotor Unit) 6 4 3 5 8 0 8 0 7 5 7 4 3 6 6 4 3 5 8 0 8 0 7 5 5 7 4 3 6 7 Series (Geroler Unit) 700
Ref. 7 Series 7 Series X 3 Sleeve 4 Spool 5 5-000 5-000 Pin 6 3037-000 3037-000 Spring, Centering for Standard Input Torque 6 370-000 370-000 Spring, Centering for Increased Input Torque 6 7 6078-00 6078-00 Ring, Retaining X 8 450-00 450-00 Seal, Quad 8a 467-000 467-000 Seal, Shaft (Lip Type see Page 5) X 500-000 500-000 O-ring 0 4565-000 4565-000 Washer 3378-000 34-000 Plate, Spacer 5 6 7 8 30 700 Screw, Cap (6 Point (E0) Drive 5/6-4 UNF) 7 3 4 5 6 004-000 004-000 Housing, Power End 34-003 34-004 Housing, Power End (Bearings, Needle Type) 4564-000 6078-0 004-008 45-000 45-000 Washer Spacer 84-004 84-004 Relief Valve S/A 53-000 53-000 Plug 5000-3 5000-3 O-ring 6-000 6-000 Spacer, Spring 4 8033-000 8033-000 Key, Woodruff X 64500-000 644-000 Seal Kit Contains parts indicated by X * 4564-000 6078-0 004-008 003-000 003-000 8 30-000 3448-000 See Separate Chart Washer Ring, Retaining Seal, Quad 7 Drive, Power End Plate, Spacer X 5776-000 5000-04 Seal, O-ring 4 0 Gerotor or Geroler Drive, Control End Housing, Valve Shaft, Power End Displ. cm 3 /r [in 3 /r] Item No. Item No. 7 Item No. 0 Item No. Cap Screws (7) Length Power End Drive () Length Gerotor or Geroler () Width Control End Drive () 76 [4.7] 64-00 50,8 [.00] 48-000 50,4 [.8] 868-033 6,3 [.5] 384-00 6 [5.] 64-00 50,8 [.00] 48-000 50,4 [.8] 868-003 3, [.5] 384-00 60 [.7] 64-5 57, [.5] 45-000 5,7 [.07] 868-004,0 [.86] 384-00 80 [4.] 64-00 50,8 [.00] 48-000 50,4 [.8] 3440-004 4,7 [.58] 384-00 0 [6.] 64-53,8 [.] 45-000 5,7 [.07] 3440-005 8,5 [.73] 384-00 60 [.7] 64-6 66,6 [.6] 45-000 5,7 [.07] 3440-007,0 [.4] 384-00 Length 58, [.3] 58, [.3] 64,0 [.5] 58, [.3] 58, [.3] 64,0 [.5] Item No. 5 Spacer () 60-05 60-00 60-00 Width,5 [.0] 3,6 [.4] 8, [.3] 3
Standard Open Center Model Housing Sleeve Spool Ref. 7 Series 7 Series 0045-00 0046-00 Housing, Valve /6-8 Ports () Open Center No Relief Valve Option 0045-003 0045-006 0045-007 0045-00 0045-0 0046-006 0046-00 0046-0 3 0736-000 0736-000 Sleeve Open Center Housing, Valve Manifold ( Mounting Holes) Open Center No Relief Valve Option Housing, Valve /6-8 Ports () Open Center with Relief Valve Option Housing, Valve Manifold ( Mounting Holes) Open Center with Relief Valve Option Housing, Valve G 3/8 (BSP) Ports () Open Center No Relief Valve Option Housing, Valve G 3/8 (BSP) Ports () Open Center with Relief Valve Option 4 0735-000 0735-000 Spool Open Center for Standard Torque Spring Pkg. 083-000 083-000 Spool Open Center for Increased Input Torque Spring Pkg. Power Beyond Model Housing Sleeve Spool Ref. 7 Series 7 Series 0045-00 0046-00 Housing, Valve /6-8 Ports (3) Power Beyond No Relief Valve Option 0045-005 0046-005 Housing, Valve /6-8 Ports (3) Power Beyond with Relief Valve Option 0045-00 0046-00 Housing, Valve G 3/8 (BSP) Ports (3) Power Beyond No Relief Valve Option 0045-0 0046-0 Housing, Valve G 3/8 (BSP) Ports (3) Power Beyond with Relief Valve Option 3 0745-000 0745-000 Sleeve Open Center Power Beyond Displacements** 4 0744-000 0744-000 Spool Open Center Power Beyond Displacements** **Standard Gerotor Displacements 76 [4.7], 6 [5.] and 80 [4.] Load Sensing Model Housing Sleeve Spool Ref. 7 Series 7 Series 0045-00 0046-00 Housing, Valve /6-8 Ports (3) Load Sensing No Relief Valve Option 0045-005 0046-005 Housing, Valve /6-8 Ports (3) Load Sensing with Relief Valve Option 0045-00 0046-00 Housing, Valve G 3/8 (BSP) Ports (3) Load Sensing No Relief Valve Option 0045-0 0046-0 Housing, Valve G 3/8 (BSP) Ports (3) Load Sensing with Relief Valve Option 3 087-000 087-000 Sleeve Load Sensing 4 086-000 086-000 Spool Load Sensing for Standard Input Torque Spring Pkg. Open Center with Case Drain Housing Sleeve Spool Ref. 7 Series 7 Series 0045-00 0046-00 Housing, Valve /6-8 Ports (3) Open Center w/case Drain No Relief Valve Option 0045-005 0046-005 Housing, Valve /6-8 Ports (3) Open Center w/case Drain and Relief Valve Option 0045-00 0046-00 Housing, Valve G 3/8 (BSP) Ports (3) Open Center w/case Drain No Relief Valve Option 0045-0 0046-0 Housing, Valve G 3/8 (BSP) Ports (3) Open Center w/case Drain and Relief Valve Option 3 0753-000 0753-000 Sleeve High Back Pressure 4 075-000 075-000 Spool Open Center High Back Pressure for Standard Input Torque Spring Pkg. 07-000 07-000 Spool Open Center High Back Pressure for Increased Input Torque Spring Pkg. 4
30 Four Spring Spacers added to outside of six springs for Increased input torque (Special Spool Required see Ref. No. 4). Three Port Housing Power Beyond Load Sensing Open Center with Case Drain With Internal Inlet Relief Without Internal Inlet Relief 7 8 6 Port Block Kit 8a 8 Two Port Housings With Internal Inlet Relief Without Internal Inlet Relief 7 Series will Accept 0 Port Block Kit N0. 08-05 Kit contains port block with two 3/8-8 NPTF ports for right angle connection, two 5/6-8 cap screws, and two o-rings. Two Input Shaft Seals Available Quad Seal Lip Seal 7 Series will require customer supplied port block contact your Eaton representative. 5
For Additional Literature Contact Eaton Corp. Hydraulics Division 55 Highway 5 Eden Prairie, MN 55344. Specifications and performance Data, Catalog No. -30 When Servicing 7 Series and 7 Series Torque Generators Refer to Repair Information No. 7-3. This Repair Manual List Tools Required, Step by Step Disassembly and Reassembly Procedures. How to Order Replacement Parts Char-Lynn Product number Week of Eaton Corp. Hydraulics Div. Year 0 Eden Prairie, MN 55344 Thru 5 Product Number 7 0000 000 Gerotor 7 0000 000 Geroler Date Code 00 00 Last Number(s) of Year Each Order Must Include the Following:. Product Number. Date Code 3. Part Name 4. Part Number 5. Quantity of Parts Product Line Identification Number Product Identification Number Engineering Change Code 6
Notes: 7
Eaton Corporation Hydraulics Division 55 Hwy. 5 Eden Prairie, MN 55344 Telephone 6/37-800 Fax 6/37-730 Eaton Ltd. Hydraulics Division Glenrothes, Fife Scotland, KY7 4NW Telephone 0-5-77-77 Fax 0-5-773-84 Eaton GmbH Hydraulics Products Am Schimmersfeld 7 40880 Ratingen, Germany Telephone 00-406-830 Fax 00-406-800 ACCREDITED BY THE DUTCH COUNCIL FOR CERTIFICATION Reg. No. 4 ISO-00 CERTIFICATED FIRM DET NORSKE VERITAS DUSTRY BV, THE NETHERLANDS Quality System Certified Products in this catalog are manufactured in an ISO-00-certified site. http://www.eaton.com Form No. 6-34 Copyright Eaton Corporation, 4, and 6 All Rights Reserved Printed in USA