Manual Motor Protectors

88 Manual Motor Protectors 51 30 UP TO IMM16 Frame IMM32 Frame IMM65 Frame E468295 E468295 High interrupt capacity up to 100k (with optional current limiter) Din rail mounting Lockable handle (OFF position) IP20 finger safe terminals Class 10 thermal overload protection Trip test feature Phase loss protection Complies with IEC 60947-1 and IEC 60947-4-1, UL508 Listed (Manual motor controller) UL508 Listed (Combination motor controller starter) CS C.22.2/14 51 35 UP TO 2 114 UL HP Ratings Thermal Short Circuit Current Part Number Price Single Phase Three Phase djustable Rating (SCCR) 115V 230V 200V 230V 460V 575V Range () 480V 600V 16 mp Frame, Pushbutton Operator IMM16-P16 30 - - - - - - 0.10 to 0.16 50k 10k IMM16-P25 30 - - - - - - 0.16 to 0.25 50k 10k IMM16-P40 30 - - - - - - 0.25 to 0.40 50k 10k IMM16-P63 30 - - - - - - 0.40 to 0.63 50k 10k IMM16-1P0 30 - - - - - 1/2 0.63 to 1.0 50k 10k IMM16-1P6 30-1/10 - - 3/4 3/4 1.0 to 1.6 50k 10k IMM16-2P5 30-1/6 1/2 1/2 1 1-1/2 1.6 to 2.5 50k 10k IMM16-4P0 30 1/8 1/3 3/4 3/4 2 3 2.5 to 4.0 50k 10k IMM16-6P3 30 1/4 1/2 1 1-1/2 3 5 4.0 to 6.3 50k 10k IMM16-010 32 1/2 1-1/2 2 3 5 7-1/2 6.3 to 10 50k 5k IMM16-016 32 1 2 3 5 10 10 10 to 16 30k 5k 32 mp Frame, Rotary Operator IMM32-P16 35 - - - - - - 0.10 to 0.16 50k 25k IMM32-P25 37 - - - - - - 0.16 to 0.25 50k 25k IMM32-P40 37 - - - - - - 0.25 to 0.40 50k 25k IMM32-P63 37 - - - - - 1/4 0.40 to 0.63 50k 25k IMM32-1P0 37 - - - - 1/2 1/2 0.63 to 1.0 50k 25k IMM32-1P6 38-1/10 1/4 1/3 3/4 1 1.0 to 1.6 50k 25k IMM32-2P5 38-1/6 1/2 1/2 1-1/2 1-1/2 1.6 to 2.5 50k 25k IMM32-4P0 40 1/8 1/3 3/4 1 2 3 2.5 to 4.0 50k 25k IMM32-6P3 40 1/4 3/4 1-1/2 1-1/2 5 5 4.0 to 6.3 50k 25k IMM32-010 40 1/2 1-1/2 3 3 7-1/2 10 6.3 to 10 50k 25k IMM32-016 40 1 3 5 5 10 15 10 to 16 50k 25k IMM32-020 45 1-1/2 3 5 7-1/2 15 20 16 to 20 50k 25k IMM32-025 48 2 3 7-1/2 7-1/2 15 20 20 to 25 50k 25k IMM32-032 48-5 10 10 20 25 25 to 32 42k 25k 65 mp Frame, Rotary Operator IMM65-040 114 3 7 1/2-15 25 40 32 to 40 35k 10k IMM65-050 114-10 15 15 30 40 40 to 50 35k 10k IMM65-065 114 5 10 20 20 50 60 50 to 65 35k 10k 51 UP TO 60HP E468295

Manual Motor Protectors (cont d) 89 IM-TDH Through-the-door Handle UL Type 1/IP55 & UL Type 4X/IP65 Padlockable & Defeatable Rotary Handle djustable shafts Shows IMM position I (ON) or O (OFF) vailable in Gray/Black or Red/Yellow Shown attached to Manual Motor Starter (sold separately) TYPE 1 / IP55 & TYPE 4X / IP65 PROTECTION IM-TDH E468295 Part Number Price Handle Color IM-TDH32-130-B1 18 Gray/Black IM-TDH32-130-Y1 18 Red/Yellow IM-TDH32-130-B4X 24 Gray/Black IM-TDH32-130-Y4X 24 Red/Yellow IM-TDH32-330-B1 19 Gray/Black IM-TDH32-330-Y1 19 Red/Yellow IM-TDH32-330-B4X 26 Gray/Black IM-TDH32-330-Y4X 26 Red/Yellow IM-TDH65-130-B4X 24 Gray/Black IM-TDH65-130-Y4X 24 Red/Yellow IM-TDH65-330-B4X 26 Gray/Black IM-TDH65-330-Y4X 26 Red/Yellow Environmental Rating TYPE 1 / IP55 TYPE 4X / IP65 TYPE 1 / IP55 TYPE 4X / IP65 TYPE 4X / IP65 TYPE 4X / IP65 Shaft Length 5.12-6.10" (130-155mm) 12.99-13.98" (330-355mm) 5.12-6.10" (130-155mm) 12.99-13.98" (330-355mm) pplicable MMP IMM32 IMM32 IMM65 MOTOR CONTROLS IMM Bus Bars For parallel connection with IMM to contactor power terminals Simplifies wiring and reduces wiring space Multiple bus bars can be combined providing total current rating Total maximum current rating 63 @ 690VC Link dapters For electrical and mechanical direct connection between IMM and contactor Simplifies wiring and reduces wiring space IM-LNKDP-16F-16MC 7 For IMM16 + IMCxxx-07S to IMCxxx-16S IM-LNKDP-16F-25MC 7 For IMM16 + IMCxxx-25S IM-LNKDP-32F-16MC 7 For IMM32 + IMCxxx-07S to IMCxxx-16S IM-LNKDP-32F-25C 7 For IMM32 + ICxxx-09S to ICxxx-25S (IC contactor C Coils Only) IM-LNKDP-32F-40C 7 For IMM32 + ICxxx-32S to ICxxx-40S (IC contactor C Coils Only) IM-ENCL-16FY IM-LNKDP-32F IM-ENCL-32xx IM-BBS32F-54-4 IM-BBLST IM-BBSHROUD Enclosed Disconnect Stations Conveniently house manual motor protector in sealed enclosure Two cable entry knockouts top and bottom Includes neutral and ground terminals Wide model available to accommodate side mounting accessories IM-ENCL-16FY 16 Standard Disconnect Station with translucent membrane for IMM16, Red/Yellow, IP66 IM-ENCL-32FB 18 Standard Disconnect Station for IMM32, Black, IP55 IM-ENCL-32FY 18 Standard Disconnect Station for IMM32, Red/Yellow, IP55 IM-ENCL-32FWB 20 Wide Disconnect Station for IMM32, Black, IP55 IM-ENCL-32FWY 20 Wide Disconnect Station for IMM32, Red/Yellow, IP55 IM-BBS32F IM-BBS32F-45-2 8 45mm for 2 IMM16 or IMM32., 63 max. total IM-BBS32F-45-3 9 45mm for 3 IMM16 or IMM32., 63 max. total IM-BBS32F-45-4 10 45mm for 4 IMM16 or IMM32., 63 max. total IM-BBS32F-45-5 12 45mm for 5 IMM16 or IMM32., 63 max. total IM-BBS32F-54-2 8 54mm for 2 IMM16 or IMM32 w/ side mount aux., 63 max. total IM-BBS32F-54-3 10 54mm for 3 IMM16 or IMM32 w/ side mount aux., 63 max. total IM-BBS32F-54-4 11 54mm for 4 IMM16 or IMM32 w/ side mount aux., 63 max. total IM-BBS32F-54-5 16 54mm for 5 IMM16 or IMM32 w/ side mount aux., 63 max. total IM-BBS32F-63-2 8 54mm for 2 IMM16 or IMM32 with 2 side mounting aux contacts IM-BBS32F-63-3 10 54mm for 3 IMM16 or IMM32 with 2 side mounting aux contacts IM-BBS32F-63-4 11 54mm for 4 IMM16 or IMM32 with 2 side mounting aux contacts IM-BBS32F-63-5 12 54mm for 5 IMM16 or IMM32 with 2 side mounting aux contacts IM-BBSHROUD 3 Busbar Shroud for unused IM-BBS32F & IM-BBS54F terminals IM-BBLST 9 ccessories Incoming Power Terminal for Bus Bar System, 3-pole, IMM16 & IMM32 IM-UX-F11 IM-LRM-S02 IM-CURLIM-32F uxiliary Contacts IM-UX-F11 8 Front mount, 1 N.O./1 N.C., 250V max IM-UX-S02 10 Left side mount, 2 N.C., 600V max IM-UX-S11 10 Left side mount, 1 N.O./1 N.C., 600V max IM-UX-S20 10 Left side mount, 2 N.O., 600V max larm & Trip Signaling Switch IM-LRM-S02 12 Left side mount, 1 N.O./1 N.C. for short-circuit signaling and 1 N.O./1 N.C. for overload signaling Shunt Release IM-SHR-C24 17 Right side mount, 20-24V, 50/60Hz IM-SHR-C127 17 Right side mount, 110V-127V, 50/60Hz IM-SHR-C240 17 Right side mount, 200-240V, 50/60Hz Undervoltage Release IM-UVR-C24 17 Right side mount, 24V, 50Hz/60Hz IM-UVR-C120 17 Right side mount, 110V-120V, 50/60Hz IM-UVR-C127 17 Right side mount, 110-115/127V, 50/60Hz IM-UVR-C208 17 Right side mount, 208V, 60Hz IM-UVR-C240 17 Right side mount, 240V, 60Hz IM-UVR-C480 17 Right side mount, 2 N.O. Contacts, 400-415/480V, 50/60Hz Current Limiter IM-CURLIM-32F 31 Provides enhanced short-circuit interrupt rating: 100k@480V for Mounting dapters IM-MBDOL-32F 13 For DOL Starters, 45mm, use w/ IMM32 + IMCxxx-07S to IMCxxx- 25S or ICxxx-09S to ICxxx-25S IM-MBREV-32F 17 For Reversing Starters, 90mm, use w/ IMM32 + (2) IMCxxx-07S to -25S or (2) ICxxx-09S to -25S IM-MBYDEL-32F 26 For Star-Delta Motor Starters, 90mm, use w/ IMM32 + (2) IMCxxx- 07S to -25S or (2) ICxxx-09S to -25S IM-MNTTB 1 Mounting tabs for (1) IMM16, IMM32 & IMM65 direct mount to any surface using screws, 2pc/pkg Scale Protection Cover IM-SDPC 3 For IMM16, IMM32 & IMM65 adjustment dial Incoming Power Terminals IM-TYPEE-32F 13 For IMM32 IM-TYPEE-65F 25 For IMM65 www.factorymation.com/motorcontrols ONLINE ORDERS FREESHIPPING SMLL PCKGES MIN. 29 500 LTL FREIGHT MIN. SEE INSIDE BCK COVER FOR MORE DETILS

90 Manual Motor Protectors (cont d) General Specifications General Specifications IMM16 IMM32 IMM65 Standards IMM Terminal Specifications 16 mp Frame 32 mp Frame 65 mp Frame IEC 60947-1/60947-4-1, EN 60947-1 / EN 60947-4-1, UL508, CS C.22.2/14 Rated Insulation (Ui) & Operating (Ue) Voltage [V] UL/CS: 600V, IEC 60947-1: 690V Rated Impulse Voltage cc. IEC60947-1 [kv] 6 Rated Operating Frequency [Hz] 50/60 Overvoltage Category Phase Failure Sensitivity Protection Overload Protection Characteristics (x lu) [] 0.61 to 1 Magnetic Release (x lu) [] 13 Overload Trip Class 10 Total Power Loss Pv t Rated Load Operating Temp [W] 6 6 (1.6 to 16) / 8 (20 to 32) 25 Utilization Category Lifespan Degree of Protection Resistance IEC 60947-2 (Motor Protector) IEC 60947-4-1 (Motor Starter) III Yes C-3 Mechanical: 100,000 ops., Electrical (le max.): 100,000 ops., Switching Rate (motor start) C-3: 15 ops/hr IP20 Shock resistance: 15g/11ms, Vibration resistance: 10g/5-150Hz Screw Driver Philips #2 Philips #2 llen #4 Terminal Capacity Environmental Conditions Solid - Stranded 1 or 2 conductors (18 to 12 WG) (see IMM Terminal Specs) (see IMM Terminal Specs) Tightening Torque [lb-in] 11 to 16 lb-in (1.2 to 1.7 Nm) 18 to 22 lb-in (2.0 to 2.5 Nm) 55 lb-in (6.2 Nm) mbient Temperature Storage: -58 to 176 F (-50 to 80 C), Operating: -4 to 140 F (-20 to 60 C) Climatic Proofing IEC 60068-2-3 / IEC 60068-2-30 ltitude (Up to 6,600ft) ltitude (Up to 6,600ft): Nominal values, Pollution degree: 3, Mounting position: ny Weight [lb] 0.7 0.7 1.42 Warranty Terminal Capacity IMM16/IMM32 Drawing (mm 2 ) (WG) 1 or 2 x (1 to 2.5) - 1 or 2 x (2.5 to 6) - 1 or 2 x (14 to 10) 1 x (8) 1 or 2 x (1 to 2.5) 1 or 2 x (2.5 to 6) 1 or 2 x (14 to 10) 10 1 x (10) Terminal Capacity IMM65 Solid Ferrule Stranded Tightening Torque 1 Conductor on Lower Part Only 12 to 2 WG 12 to 2 WG B 2 Conductors, 1 on Upper Part () and 1 on Lower Part (B) 16 to 2 WG 16 to 2 WG 12 to 2 WG 16 to 2 WG 16 to 2 WG 12 to 2 WG 8 to 2 WG 14 to 2 WG 14 to 2 WG 8 to 2 WG 55 lb-in (6.2 Nm) B 1 year Trip Characteristics Extended Rotary Handle Dimensions in(mm) Manual Motor Protector Dimensions in(mm) B C D verage Curves Curve 1: 3 pole Curve 2: Bipolar with phase loss sensitivity Tripping time as function of the current at cold condition. For warm condition (after submitted to the rated operational current - Ie ), the tripping times reduce to approximately 25%. E-Handle Type Min Max Inches (mm) MMS Type IM-THD32 (TYPE 1) 5.9 8.3 (148.6 210.6) IMM32 IM-TDH32 (TYPE 4X) 5.9 16.2 (148.6 410.6) IMM32 IM-TDH65 (TYPE 4X) 7.6 10.1 (193.6 255.6) IMM65 in (mm) Dimensions B C D IMM16 2.99 (76) 1.77 (45) 3.94 (100) 1.77 (45) IMM32 3.86 (98) 1.77 (45) 3.82 (97) 1.77 (45 IMM65 6.18 (157) 2.13 (54) 4.92 (125) 4.50 (114) The characteristics of the magnetic trip are based on the upper value of the setting range for IMM16, IMM32 & IMM65.

Miniature Contactors & Overloads 91 15 7 25 1/ 1 16 Frame E468299 E108780 1/ to 1 Surface or DIN rail mountable UL508 Listed 50/60Hz C and DC coil versions available Direct-mounting overloads RoHS compliant uxiliary contacts standard (16 Frame) IEC 60947 Optional ccessories Include: dditional auxiliary contact blocks Reverse mounting kits and interlocks Surge suppressors Direct mount to Manual Motor Starter (with optional adapter) Miniature Thermal Overload Relays IMC-LCHBLK-16F 3-pole Contactors 3-pole Overloads 2-pole Overloads Price Current Range pplicable Contactor IMOL-16S-P40 IMOLS-16S-P40 14 0.28-0.40 IMOL-16S-P63 IMOLS-16S-P63 14 0.40-0.63 IMCxxx-07S IMOL-16S-P80 IMOLS-16S-P80 14 0.56-0.80 IMCxxx-09S IMOL-16S-1P2 IMOLS-16S-1P2 14 0.80-1.2 IMCxxx-12S IMOL-16S-1P8 IMOLS-16S-1P8 14 1.2-1.8 IMCxxx-16S IMOL-16S-2P8 IMOLS-16S-2P8 14 1.8-2.8 IMOL-16S-4P0 IMOLS-16S-4P0 14 2.8-4.0 IMOL-16S-6P3 IMOLS-16S-6P3 14 4.0-6.3 IMOL-16S-8P0 IMOLS-16S-8P0 14 5.6-8.0 IMCxxx-07S IMCxxx-09S IMOL-16S-010 IMOLS-16S-010 14 7-10 IMCxxx-12S IMOL-16S-012 IMOLS-16S-012 14 8-12.5 IMCxxx-16S IMOL-16S-015 IMOLS-16S-015 14 10-15 IMOL-16S-017 IMOLS-16S-017 14 11-17 IMOL-25S-023 IMOLS-25S-023 15 15-23 IMOL-25S-032 IMOLS-25S-032 15 23-32 IMCxxx-25S IMH-SMB-25F 4 FMX Separate Mounting Bracket for IMOL-16S to IMOL-25S, screw or DIN-rail mountable IMOL-16S 11 Part Number UL HP Ratings (C3 Motor Load) Optional Price Coil Voltage Single Phase Three Phase Overload 1 N.O. ux Contact 1 N.C. ux Contact 115V 230V 230V 460V 575V Relay 16 Frame Size IMC330-07S-10-C24 IMC330-07S-01-C24 11 24VC (60Hz) IMC330-07S-10-C120 IMC330-07S-01-C120 11 110/120VC (50/60Hz) IMC330-07S-10-C240 IMC330-07S-01-C240 11 208-240VC (60Hz) 1/ 3/4HP 1-1/ IMC330-07S-10-C480 IMC330-07S-01-C480 11 400-415/480VC (7.2) (7) (7) IMOL-16S IMC330-07S-10-DC12-14 12VDC IMC330-07S-10-DC24 IMC330-07S-01-DC24 14 24VDC IMC330-09S-10-C24-12 24VC (60Hz) IMC330-09S-10-C120-12 110/120VC (50/60Hz) IMC330-09S-10-C240-12 208-240VC (60Hz) IMC330-09S-10-C480-12 400-415/480VC (50/60Hz) IMC330-09S-10-DC12-15 12VDC IMC330-09S-10-DC24-15 24VDC IMC330-12S-10-C24-13 24VC (60Hz) IMC330-12S-10-C120-13 110/120VC (50/60Hz) IMC330-12S-10-C240-13 208-240VC (60Hz) IMC330-12S-10-C480-13 400-415/480VC (50/60Hz) IMC330-12S-10-DC12-16 12VDC IMC330-12S-10-DC24-16 24VDC IMC330-16S-10-C24 IMC330-16S-01-C24 15 24VC (60Hz) IMC330-16S-10-C120 IMC330-16S-01-C120 15 110/120VC (50/60Hz) IMC330-16S-10-C240 IMC330-16S-01-C240 15 208-240VC (60Hz) IMC330-16S-10-C480 IMC330-16S-01-C480 15 400-415/480VC (50/60Hz) IMC330-16S-10-DC12-19 12VDC IMC330-16S-10-DC24 IMC330-16S-01-DC24 19 24VDC IMC-MECINT-16F Mini Series ccessories 1/3 HP (9.8) 1/ (12.8) 1HP IMC330-16S-10-DC110-19 110VDC 25 Frame Size (ux contacts sold separately) IMC330-25S-00-C24 16 24VC (60Hz) IMC330-25S-00-C120 IMC330-25S-00-C240 16 16 110/120VC (50/60Hz) 208-240VC (60Hz) 1-1/ (22) IMC330-25S-00-C480 16 400-415/480VC (50/60Hz) IMC-UX-316-F11 1HP (12) (25) (12) 7-1/ (22) Part Number Price Description uxiliary Contacts IMC-UX-316-F02 4 Front mount, 2 N.C., IMCxxx-07S to -16S Contactors IMC-UX-316-F04 7 Front mount, 4 N.C., IMCxxx-07S to -16S Contactors IMC-UX-316-F11 4 Front mount, 1 N.O./1 N.C., IMCxxx-07S to -16S Contactors IMC-UX-316-F20 4 Front mount, 2 N.O., IMCxxx-07S to -16S Contactors IMC-UX-316-F22 7 Front mount, 2 N.O./ 2 N.C., IMCxxx-07S to -16S Contactors IMC-UX-316-F40 7 Front mount, 4 N.O., IMCxxx-07S to -16S Contactors IMC-UX-325-F02 4 Front mount, 2 N.C., IMCxxx-25S Contactors 7-1/ IMC-UX-325-F11 4 Front mount, 1 N.O./1 N.C., IMCxxx-25S Contactors IMOL-16S 7-1/ 7-1/ IMOL-16S (12) 1 (22) 1 (27) IMOL-16S IMOL-25S IMC-UX-325-F20 4 Front mount, 2 N.O., IMCxxx-25S Contactors Latch Block IMC-LCHBLK-16F 3 For IMCxxx-07S to -16S Contactors Mechanical Interlock Block for Reversing Configuration IMC-MECINT-16F 3 For IMCxxx-07S to -16S, front mount Reverse Wire Kit for Reversing Starters IMC-REVKIT-16F 9 For IMCxxx-07S-01 to -16S-01 (N.C. aux. contactors only). ssemble IMOL-16S to -25S and IMM16 to 32 Surge Suppressors IMC-DIODE-16F-DC600 3 Diode, Front Mount, 12-600VDC IMC-RCSURG-25F-C127 3 RC, Front Mount, 50-127VC, 50/60Hz IMC-RCSURG-25F-C24 3 RC, Front Mount, 12-24VC, 50/60Hz IMC-RCSURG-25F-C250 3 RC, Front Mount, 130-250VC, 50/60Hz IMC-RCSURG-25F-C510 3 RC, Front Mount, 400-510VC, 50/60Hz IMC-VRSURG-25F-D127 3 Varistor, Front Mount, 50-127VC / 60-180VDC IMC-VRSURG-25F-D275 3 Varistor, Front Mount, 130-275VC / 180-300VDC IMC-VRSURG-25F-D380 3 Varistor, Front Mount, 277-380VC / 300-510VDC IMC-VRSURG-25F-D48 3 Varistor, Front Mount, 12-48VC / 12-60VDC IMC-VRSURG-25F-D510 3 Varistor, Front Mount, 400-510VC 50-60Hz Link dapters IM-LNKDP-16F-16MC 7 For IMM16 + IMCxxx-07S to IMCxxx-16S IM-LNKDP-16F-25MC 7 For IMM16 + IMCxxx-25S IM-LNKDP-32F-16MC 7 For IMM32 + IMCxxx-07S to IMCxxx-16S MOTOR CONTROLS www.factorymation.com/motorcontrols IMC-REVKIT-16F IMC-RCSURG-25F-C127 IM-LNKDP-16F-16MC ONLINE ORDERS FREESHIPPING SMLL PCKGES MIN. 29 500 LTL FREIGHT MIN. SEE INSIDE BCK COVER FOR MORE DETILS

2.77(70) 92 Miniature Contactors & Overloads (cont d) E468299 E108780 1/ to Surface or DIN rail mountable UL508 Listed 50/60Hz C and DC coil versions available IEC 60947 Optional ccessories Include: dditional auxiliary contact blocks Reverse mounting kits and interlocks Surge suppressors Dimensions in(mm) IMCxxx-07S to -16S 3.4(86) 2.0(51) 13 15 7 16 1/ 16 Frame 4-pole Contactors 2 NO Power Poles 2 NC Power Poles Price 4 NO Power Poles Price Coil Voltage 16 Frame Size IMC422-07S-00-C24 13 IMC440-07S-00-C24 13 24VC (60Hz) IMC422-07S-00-C120 13 IMC440-07S-00-C120 13 110/120VC (50/60Hz) IMC422-07S-00-C240 13 IMC440-07S-00-C240 13 208-240VC (60Hz) IMC422-07S-00-C480 13 IMC440-07S-00-C480 13 400-415/480VC IMC422-07S-00-DC12 16 IMC440-07S-00-DC12 16 12VDC IMC422-07S-00-DC24 16 IMC440-07S-00-DC24 16 24VDC IMC422-07S-00-DC110 16 IMC440-07S-00-DC110 16 110VDC IMC422-09S-00-C24 14 IMC440-09S-00-C24 14 24VC (60Hz) IMC422-09S-00-C120 14 IMC440-09S-00-C120 14 110/120VC (50/60Hz) IMC422-09S-00-C240 14 IMC440-09S-00-C240 14 208-240VC (60Hz) IMC422-09S-00-C480 14 IMC440-09S-00-C480 14 400-415/480VC IMC422-09S-00-DC12 17 IMC440-09S-00-DC12 17 12VDC IMC422-09S-00-DC24 17 IMC440-09S-00-DC24 17 24VDC IMC422-09S-00-DC110 17 IMC440-09S-00-DC110 17 110VDC IMC422-12S-00-C24 14 IMC440-12S-00-C24 14 24VC (60Hz) IMC422-12S-00-C120 14 IMC440-12S-00-C120 14 110/120VC (50/60Hz) IMC422-12S-00-C240 14 IMC440-12S-00-C240 14 208-240VC (60Hz) IMC422-12S-00-C480 14 IMC440-12S-00-C480 14 400-415/480VC IMC422-12S-00-DC12 19 IMC440-12S-00-DC12 19 12VDC IMC422-12S-00-DC24 19 IMC440-12S-00-DC24 19 24VDC IMC422-12S-00-DC110 19 IMC440-12S-00-DC110 19 110VDC IMC422-16S-00-C24 19 IMC440-16S-00-C24 19 24VC (60Hz) IMC422-16S-00-C120 19 IMC440-16S-00-C120 19 110/120VC (50/60Hz) IMC422-16S-00-C240 19 IMC440-16S-00-C240 19 208-240VC (60Hz) IMC422-16S-00-C480 19 IMC440-16S-00-C480 19 400-415/480VC IMC422-16S-00-DC12 21 IMC440-16S-00-DC12 21 12VDC IMC422-16S-00-DC24 21 IMC440-16S-00-DC24 21 24VDC IMC422-16S-00-DC110 21 IMC440-16S-00-DC110 21 110VDC Screw Mount 1.5(38) 3.3(84) 2.2 (56) 1.8(46) UL HP Ratings (C3 Motor Load) Single Phase Three Phase 115V 230V 230V 460V 575V 1/ (7.2) 1/3 HP (9.8) 1/ (12.8) 1HP 3/4HP 1HP (12) 1-1/ (7) (12) (7) 7-1/ 7-1/ 7-1/ (12) 2.3(58) IMC IMC-UX IMC-LCHBLK-16F or IMC-MECINT-16F 2.0(51) 2.3(58) 4.5(114) IMC IMOL IMOL-16S / -25S 1.77(45) IMCxxx-25S 3.3(84) 2.2(56) 2.3(58) IMC IMC-UX 3.26(83)

Miniature Contactors & Overloads (cont d) 93 Miniature Contactor Specifications General Specifications IMCxxx-07S IMCxxx-09S IMCxxx-12S IMCxxx-16S IMCxxx-25S General Purpose Rating () 18 20 22 22 32 Rated Operational Voltage (V) 12 to 690 Rated Insulation Voltage (V) UL/CS: 600, IEC/VDE 0660: 690 Rated Impulse Voltage IEC60947-1 (V) 4000 Rated Operating Frequency (Hz) 25 to 400 Degree of Protection Vibration Resistance (5 to 200Hz) IP20 Contactor Open (g) 2 Contactor Closed at Coil (g) 4 Mechanical Endurance (Million ops) 10 (C Coil) / 12 (DC Coil) 3 (C Coil) Electrical Endurance (Million ops) 1.4 1.3 1.2 1 0.6 Shock Resistance Contactor Open (g) 6 6 6 6 6 (1/2 Sin Wave = 11ms) Contactor Closed at Coil (g) 10 10 10 10 10 Terminal Capacity Main Contacts (WG) 1 or 2 x (18 to 12) 1 or 2 x (18 to 12) 1 or 2 x (18 to 12) 1 or 2 x (18 to 12) 1 or 2 x (18 to 10) Screw Driver Phillips #2 Phillips #2 Phillips #2 Phillips #2 Phillips #2 Tightening Torque (lb-in) 10 10 10 10 13 Environmental Conditions mbient Temperature Storage: -67 to 176 F (-55 to 80 C), Operating: -4 to 140 F (-20 to 60 C) Climatic Withstand ccording to IEC 60680-2 Pollution Degree 3 Mounting 35mm DIN-rail cc. DIN EN 50 022 Weight (lb) 0.42 0.42 0.42 0.42 0.42 Control Circuit Ratings (C/DC COIL) Standard Voltages Coil Operating Limits Coil Consumption (Single coils) Power Factor Operating Time Miniature Overload Specifications General Specifications 12 to 660 (60Hz) Monofrequency Coils (NO LOD) (V) 0.85 to 1.1 Pick-up (V) 0.40 to 0.76 (C-60Hz) / 0.40 to 0.70 (DC) Drop-out (V) 0.25 to 0.65 (C-60Hz) / 0.15 to 0.40 (DC) Sealed (V) 2.5 to 3.5 2.5 to 3.5 2.5 to 3.5 2.5 to 3.5 10.8 to 13.2 Inrush (V) 35 35 35 35 72 Closed Cos Φ 0.28 0.28 0.28 0.28 0.32 Opened Cos Φ 0.85 0.85 0.85 0.85 0.93 Coil Energization - N.O. (ms) 8 to 20 (C-60Hz) / 10 to 20 (DC) 13 to 16 (C-60Hz) Coil De-energization - N.O. (ms) 5 to 15 (C-60Hz) / 2 to 8 (DC) 13.5 to 17 (C-60Hz) Standards IEC 60947-1 / 60947-4-1, UL 508; CS C.22.2/14; VDE 0660/102 Number of Poles 3 Rated Operation & Insulation Voltage [V] UL/CS: 600, IEC 60947-4-1: 690 Rated Impulse Voltage, Uimp [kv] 6 Tripping Class 10 Phase Failure Sensitivity Current Direct lternating [Hz] Up to 400 Shock Resistance (IEC 60068-2-27; 1/2 sine wave) [g/ms] 10/11 Power Terminals IP Rating Main Terminals Capacity IMOL Yes Yes IP10 Cross/Slotted Combination Stranded / Solid (UL/CS) [WG] 14-6 Tightening Torque [lb-in] 20 Environmental Conditions mbient Temperature Storage: -58 to 176 F (-50 to 80 C), Operating: -4 to 158 C (-20 to 70 C) Pollution Degree 3 Higher Value of Setting Range 3 Weight [lb] 0.33 uxiliary Contacts Specifications Front uxiliary Contact Rated uxiliary Contacts C-14/15 DC-13/14 UL/CS 1 NO / 1 NC 24V:4, 60V:3.5, 125V:3, 230V:2, 400V:1.5, 500V:0.5, 690V:0.3 24V:1, 60V:0.5, 110V:0.25, 220V:0.1 Rated Thermal Current [] 6 Short Circuit Protection (Time-delay Fuse ) [] 6 C600 ; R300 uxiliary Terminals Capacity [WG] 16-12 Tightening Torque [lb-in] 13.3 MOTOR CONTROLS www.factorymation.com/motorcontrols ONLINE ORDERS FREESHIPPING SMLL PCKGES MIN. 29 500 LTL FREIGHT MIN. SEE INSIDE BCK COVER FOR MORE DETILS

94 Standard Contactors & Overloads 15 E468299 3/4HP to 7 DIN rail mountable up to 105 frame UL508 Listed UL and CE Certified IEC 60947 Optional ccessories Include: dditional auxiliary contact blocks Replacement coils Mechanical interlock blocks Link adapters for MMS Coil surge suppression Electronic modules 40 Frame Size 80 Frame Size 105 Frame Size 14 25 Frame Size 7.6 104 18 Frame Size 31 54 106 3/4HP 7 Contactors Part Number Price Coil Voltage ux. Contacts 18 Frame Size IC330-09S-10-C24 14 24VC (60Hz) 1 N.O. IC330-09S-10-C120 14 110/120VC (50/60Hz) 1 N.O. IC330-09S-10-C240 14 208-240VC (60Hz) 1 N.O. IC330-09S-10-C480 14 400-415/480VC (50/60Hz) 1 N.O. IC330-09S-10-C600 14 500/600VC (50/60Hz) 1 N.O. IC330-09S-10-DC24 16 24VDC 1 N.O. IC330-09S-01-DC24 16 24VDC 1 N.C. IC330-12S-10-C24 16 24VC (60Hz) 1 N.O. IC330-12S-10-C120 16 110/120VC (50/60Hz) 1 N.O. IC330-12S-10-C240 16 208-240VC (60Hz) 1 N.O. IC330-12S-10-C480 16 400-415/480VC (50/60Hz) 1 N.O. IC330-12S-10-C600 16 500/600VC (50/60Hz) 1 N.O. IC330-12S-10-DC24 18 24VDC 1 N.O. IC330-12S-01-DC24 18 24VDC 1 N.C. IC330-18S-10-C24 22 24VC (60Hz) 1 N.O. IC330-18S-10-C120 22 110/120VC (50/60Hz) 1 N.O. IC330-18S-10-C240 22 208-240VC (60Hz) 1 N.O. IC330-18S-10-C480 22 400-415/480VC (50/60Hz) 1 N.O. IC330-18S-10-C600 22 500/600VC (50/60Hz) 1 N.O. IC330-18S-10-DC24 25 24VDC 1 N.O. IC330-18S-01-DC24 25 24VDC 1 N.C. 25 Frame Size IC330-25S-00-C24 24 24VC (60Hz) - IC330-25S-00-C120 24 110/120VC (50/60Hz) - IC330-25S-00-C240 24 208-240VC (60Hz) - IC330-25S-00-C480 24 400-415/480VC (50/60Hz) - IC330-25S-00-DC24 28 24VDC - 40 Frame Size IC330-32S-00-C24 31 24VC (60Hz) - IC330-32S-00-C120 31 110/120VC (50/60Hz) - IC330-32S-00-C240 31 208-240VC (60Hz) - IC330-32S-00-C480 31 400-415/480VC (50/60Hz) - IC330-32S-00-DC28 36 24-28VDC - IC330-40S-00-C24 39 24VC (60Hz) - IC330-40S-00-C120 39 110/120VC (50/60Hz) - IC330-40S-00-C240 39 208-240VC (60Hz) - IC330-40S-00-C480 39 400-415/480VC (50/60Hz) - IC330-40S-00-DC28 45 24-28VDC - 80 Frame Size IC330-50S-00-C24 54 24VC (60Hz) - IC330-50S-00-C120 54 110/120VC (50/60Hz) - IC330-50S-00-C240 54 208-240VC (60Hz) - IC330-50S-00-C480 54 400-415/480VC (50/60Hz) - IC330-50S-00-DC28 57 24-28VDC - IC330-65S-00-C24 62 24VC (60Hz) - IC330-65S-00-C120 62 110/120VC (50/60Hz) - IC330-65S-00-C240 62 208-240VC (60Hz) - IC330-65S-00-C480 62 400-415/480VC (50/60Hz) - IC330-65S-00-DC28 62 24-28VDC - IC330-80S-00-C24 64 24VC (60Hz) - IC330-80S-00-C120 64 110/120VC (50/60Hz) - IC330-80S-00-C240 64 208-240VC (60Hz) - IC330-80S-00-C480 64 400-415/480VC (50/60Hz) - IC330-80S-00-DC28 70 24-28VDC - 105 Frame Size IC330-95S-00-C24 106 24VC (60Hz) - IC330-95S-00-C120 106 110/120VC (50/60Hz) - IC330-95S-00-C240 106 208-240VC (60Hz) - IC330-95S-00-C480 106 400-415/480VC (50/60Hz) - IC330-95S-00-DC28 111 24-28VDC - IC330-105S-00-C24 116 24VC (60Hz) - IC330-105S-00-C12 0 116 110/120VC (50/60Hz) - IC330-105S-00-C240 116 208-240VC (60Hz) - IC330-105S-00-C480 116 400-415/480VC (50/60Hz) - IC330-105S-00-DC28 131 24-28VDC - UL HP Ratings (C3 Motor Load) Optional Single Phase Three Phase Overload 115V 230V 200V 230V 460V 575V Relay 0.7 1. (9.8) (10) 0.7 (13.8) 1HP (24) (34) (34) (56) (56) 7. (80) 7. (80) (12) (28) (28) 7. (40) 7. (40) (50) 1 (68) 1 (68) 20HP (100) (88) (9.6) (9.6) (17.5) (15.2) 7. (25) 7. (22) (32.2) (28) 1 (32.2) (42) 1 1 (48.3) (42) 20HP 20HP (62.1) (54) 20HP 2 (62.1) (68) 2 30HP (78.2) (80) 30HP (92) (7.6) 7. (14) 1 (21) 20HP (27) 30HP (40) 40HP (52) 50HP (65) 50HP (65) 60HP (77) 40HP 7 (104) (96) 7. 1 1 2 (27) 2 (27) 40HP (41) 50HP (52) 60HP (62) 7 (77) 7 (77) IOL-40S IOL-40S IOL-80S IOL-80S IOL-80S IOL- 105S IOL- 105S

Standard Contactors & Overloads (cont d) 95 1 5 187 99 336 UP TO 350HP 150 to 300 IC330-112L E468299 Up to 350HP UL508 Listed UL and CE Certified IEC 60947 Optional ccessories Include: uxiliary contact blocks Replacement coils Part Number Price Coil Voltage ux. Contacts 150 Frame Size IC330-112L-22-D28 187 24-28VC/DC 2 N.O./2 N.C. IC330-112L-22-D130 187 110-130VC/DC 2 N.O./2 N.C. IC330-112L-22-D250 187 208-250VC/DC 2 N.O./2 N.C. IC330-112L-22-D500 187 430-500VC/DC 2 N.O./2 N.C. IC330-150L-22-D28 218 24-28VC/DC 2 N.O./2 N.C. IC330-150L-22-D130 218 110-130VC/DC 2 N.O./2 N.C. IC330-150L-22-D250 218 208-250VC/DC 2 N.O./2 N.C. IC330-150L-22-D500 218 430-500VC/DC 2 N.O./2 N.C. 180 Frame Size IC330-180L-22-D130 306 110-130VC/DC 2 N.O./2 N.C. IC330-180L-22-D250 306 208-250VC/DC 2 N.O./2 N.C. IC330-180L-22-D500 306 430-500VC/DC 2 N.O./2 N.C. 300 Frame Size IC330-250L-22-D28 434 24-28VC/DC 2 N.O./2 N.C. IC330-250L-22-D130 434 110-130VC/DC 2 N.O./2 N.C. IC330-250L-22-D250 434 208-250VC/DC 2 N.O./2 N.C. IC330-250L-22-D500 434 430-500VC/DC 2 N.O./2 N.C. IC330-300L-22-D28 451 24-28VC/DC 2 N.O./2 N.C. IC330-300L-22-D130 451 110-130VC/DC 2 N.O./2 N.C. IC330-300L-22-D250 451 208-250VC/DC 2 N.O./2 N.C. IC330-300L-22-D500 451 430-500VC/DC 2 N.O./2 N.C. UL HP Ratings (C3 Motor Load) Single Phase Three Phase 115V 230V 200V 230V 460V 575V - - - - - - - - - - 40HP (120) 50HP (150) 60HP (177) Optional Overload Relay 50HP 100HP 100HP IOL-150L (130) (124) (99) 60HP 12 150HP IOL-150L (154) (156) (144) 7 150HP 200HP IOL-180L (192) (180) (192) 7 100HP 200HP 250HP IOL-300L (221) (248) (240) (242) 100HP 12 250HP 350HP IOL-300L (285) (312) (302) (336) MOTOR CONTROLS Contactor ccessories uxiliary Contacts IC-UX-F10 3 Front Mount, 1NO, for ICxxx-09S to -105S contactors IC-UX-F01 3 Front Mount, 1NC, for ICxxx-09S to -105S contactors IC-UX-S11 6 Side Mount, 1NO/1NC for ICxxx-09S to ICxxx-300L contactors IC-UX-S20 6 Side Mount, 2NO, for ICxxx-09S to ICxxx-300L contactors IC-UX-S11X 6 Side Mount, 2nd Block, 1NO/1NC, for ICxxx-09S to ICxxx-300L contactors IC-UX-S20X 6 Side Mount, 2nd Block, 2NO, for ICxxx-09S to ICxxx-300L contactors Mechanical Interlock Blocks IC-MECINT02-105F 11 Side mount between two ICxxx-09S to ICxxx-105S contactors Side mount between two ICxxx-112L to ICxxx-300L contactors w/ IC-MECINT00-300F 22 the same frame size Link dapters (Electrical and Mechanical Direct Connection) IM-LNKDP-32F-25C 7 For IMM32 + ICxxx-09S to ICxxx-25S (IC contactor C Coils Only) IM-LNKDP-32F-40C 7 For IMM32 + ICxxx-32S to ICxxx-40S (IC contactor C Coils Only) Lug Terminals IC-LUGS-150F FMX Lugs for ICxxx-112L to ICxxx-150L, 300 MCM to 6 WG wire 22 size, 3 pack IC-LUGS-180F 26 FMX Lugs for ICxxx-180L, 300 MCM to 6 WG wire size, 3 pack IC-LUGS-300F FMX Lugs for ICxxx-250S to ICxxx-300L, 300 MCM to 6 WG wire 46 size, 3 pack Surge Suppressors IC-VRSURG-105F-C510 6 Varistor, ICxxx-09S to ICxxx-105S, 400 to 510VC IC-RCSURG-40F-C48 8 RC, ICxxx-09S to ICxxx-40S, 24 to 48VC IC-RCSURG-40F-C127 8 RC, ICxxx-09S to ICxxx-40S, 50 to 127VC IC-RCSURG-40F-C250 8 RC, ICxxx-09S to ICxxx-40S, 130 to 250VC IC-RCSURG-105F-C48 8 RC, ICxxx-50S to ICxxx-105S, 24 to 48VC IC-RCSURG-105F-C127 8 RC, ICxxx-50S to ICxxx-105S, 50 to 127VC IC-RCSURG-105F-C250 8 RC, ICxxx-50S to ICxxx-105S, 130 to 250VC IC-RCSURG-250F-C48 8 RC, ICxxx-112L to ICxxx-250L, 24 to 48VC IC-RCSURG-250F-C250 8 RC, ICxxx-112L to ICxxx-250L, 50 to 250VC IC-DIODE-25F-DC600 8 Diode, ICxxx-09S to ICxxx-25S, 12 to 600VDC Replacement Contactor Coils ICR-COIL-25F-C24 9 ICxxx-09 to ICxxx-25, 24VC, 60Hz ICR-COIL-25F-C120 9 ICxxx-09 to ICxxx-25, 110/120VC, 50/60Hz ICR-COIL-25F-C240 9 ICxxx-09 to ICxxx-25, 208-240VC, 60Hz ICR-COIL-25F-C480 9 ICxxx-09 to ICxxx-25, 400-415/480VC, 50/60Hz ICR-COIL-25F-C600 9 ICxxx-09 to ICxxx-25, 500/600VC, 50/60Hz ICR-COIL-25F-DC24 14 ICxxx-09 to ICxxx-25, 24VDC ICR-COIL-40F-C24 10 ICxxx-32 to ICxxx-40, 24VC, 60Hz ICR-COIL-40F-C120 10 ICxxx-32 to ICxxx-40, 110/120VC, 50/60Hz ICR-COIL-40F-C240 10 ICxxx-32 to ICxxx-40, 208-240VC, 60Hz ICR-COIL-40F-C480 10 ICxxx-32 to ICxxx-40, 400-415/480VC, 50/60Hz ICR-COIL-40F-C600 10 ICxxx-32 to ICxxx-40, 500/600VC, 50/60Hz ICR-COIL-40F-DC24 16 ICxxx-32 to ICxxx-40, 24VDC ICR-COIL-40F-DF240 10 ICxxx-32 to ICxxx-40, 208/240VC, 50/60Hz ICR-COIL-105F-C120 14 ICxxx-50 to ICxxx-105, 110/120VC, 50/60Hz ICR-COIL-105F-C240 14 ICxxx-50 to ICxxx-105, 208-240VC, 60Hz ICR-COIL-105F-C480 14 ICxxx-50 to ICxxx-105, 400-415/480VC, 50/60Hz ICR-COIL-105F-C600 14 ICxxx-50 to ICxxx-105, 500/600VC, 50/60Hz ICR-COIL-105F-DC24 21 ICxxx-50 to ICxxx-105, 24VDC Replacement Contactor Coils 150-300 Frame ICR-COIL-150F-D28* 20 ICxxx-112 to ICxxx-150, 24-28VC/DC*Use w/icr-emod-300f-d28* ICR-COIL-150F-D130* 20 ICxxx-112 to ICxxx-150,110-130VC/DC*Use w/icr-emod-300f-d130* ICR-COIL-150F-D250* 20 ICxxx-112 to ICxxx-150, 208-250VC/DC*Use w/icr-emod-300f-d250* ICR-COIL-150F-D500* 20 ICxxx-112 to ICxxx-150, 430-500VC/DC*Use w/icr-emod-300f-d500* ICR-COIL-180F-D28* 26 ICxxx-180L, 24-28VC/DC*Use w/icr-emod-300f-d28* ICR-COIL-180F-D130* 26 ICxxx-180L,110-130VC/DC*Use w/icr-emod-300f-d130* ICR-COIL-180F-D250* 26 ICxxx-180L, 208-250VC/DC*Use w/icr-emod-300f-d250* ICR-COIL-180F-D500* 26 ICxxx-180L, 430-500VC/DC*Use w/icr-emod-300f-d500* ICR-COIL-300F-D28* 33 ICxxx-250 to ICxxx-300, 24-28VC/DC*Use w/icr-emod-300f-d28* ICR-COIL-300F-D130* 33 ICxxx-250 to ICxxx-300,110-130VC/DC*Use w/icr-emod-300f-d130* ICR-COIL-300F-D250* 33 ICxxx-250 to ICxxx-300, 208-250VC/DC*Use w/icr-emod-300f-d250* ICR-COIL-300F-D500* 33 ICxxx-250 to ICxxx-300, 430-500VC/DC*Use w/icr-emod-300f-d500* Replacement Electronic Modules ICR-EMOD-300F-D28* 71 ICxxx-112 to ICxxx-300, 24-28VC/DC*Use w/ ICR-COIL-xxxx-D28* ICR-EMOD-300F-D130* 71 ICxxx-112 to ICxxx-300,110-130VC/DC*Use w/ ICR-COIL-xxxx-D130* ICR-EMOD-300F-D250* 71 ICxxx-112 to ICxxx-300, 208-250VC/DC*Use w/ ICR-COIL-xxxx-D250* ICR-EMOD-300F-D500* 71 ICxxx-112 to ICxxx-300, 430-500VC/DC*Use w/ ICR-COIL-xxxx-D500* *Replacement Coils 112 and above must be paired with an Electronic Module www.factorymation.com/motorcontrols IC-UX-F10 IC-UX-S11 IM-LNKDP-32F Lug Terminals Surge Suppressor ONLINE ORDERS FREESHIPPING SMLL PCKGES MIN. 29 500 LTL FREIGHT MIN. SEE INSIDE BCK COVER FOR MORE DETILS

96 Standard Contactors & Overloads (cont d) 18 Thermal Overload Relays 3-pole Overloads 2-pole Overloads Price ux Contacts Current Range pplicable Contactor 15 Trip ranges from 0.28 to 420 Separate mount adapter available (through IOL-105S) mbient compensated -4 to 140 F (-20 to 60 C) Selectable RESET button (auto or manual) Differential current / phase loss protection Isolated 1N.O. & 1 N.C. auxiliary contacts Trip class 10 UL and CE Certified UL508 / IEC 60947 IOL-80S IOL-105S IOL-40S 0.28 420 E468296 37 54 -P40 IOLS-25S-P40 18 1 N.O. / 1N.C. 0.28-.040 -P63 IOLS-25S-P63 18 1 N.O. / 1N.C 0.40-0.63 -P80 IOLS-25S-P80 18 1 N.O. / 1N.C. 0.56-0.8-1P2 IOLS-25S-1P2 18 1 N.O. / 1N.C 0.8-1.2-1P8 IOLS-25S-1P8 18 1 N.O. / 1N.C. 1.2-1.8-2P8 IOLS-25S-2P8 18 1 N.O. / 1N.C 1.8-2.8-4P0 IOLS-25S-4P0 18 1 N.O. / 1N.C. 2.8-4.0-6P3 IOLS-25S-6P3 18 1 N.O. / 1N.C 4.0-6.3-8P0 IOLS-25S-8P0 18 1 N.O. / 1N.C. 5.6-8.0-010 IOLS-25S-010 18 1 N.O. / 1N.C 7-10 -012 IOLS-25S-012 18 1 N.O. / 1N.C. 8-12.5-015 IOLS-25S-015 18 1 N.O. / 1N.C 10-15 -017 IOLS-25S-017 18 1 N.O. / 1N.C. 11-17 -023 IOLS-25S-023 18 1 N.O. / 1N.C. 15-23 -032 IOLS-25S-032 18 1 N.O. / 1N.C 22-32 ICxxx-09S ICxxx-12S ICxxx-18S ICxxx-25S ICxxx-09S ICxxx-12S ICxxx-18S ICxxx-25S ICxxx-32S ICxxx-40S IOL-40S-040 IOLS-40S-040 33 1 N.O. / 1N.C. 25-40 ICxxx-32S IOL-40S-050 IOLS-40S-050 33 1 N.O. / 1N.C 32-50 ICxxx-40S IOL-80S-040 IOLS-80S-040 37 1 N.O. / 1N.C 25-40 IOL-80S-050 IOLS-80S-050 37 1 N.O. / 1N.C. 32-50 IOL-80S-057 IOLS-80S-057 37 1 N.O. / 1N.C 40-57 IOL-80S-063 IOLS-80S-063 37 1 N.O. / 1N.C. 50-63 IOL-80S-070 IOLS-80S-070 40 1 N.O. / 1N.C. 57-70 IOL-80S-080 IOLS-80S-080 40 1 N.O. / 1N.C. 63-80 IOL-105S-080-54 1 N.O. / 1N.C 63-80 IOL-105S-097-54 1 N.O. / 1N.C. 75-97 IOL-105S-112-54 1 N.O. / 1N.C 90-112 IOL-150L-097-LK - 130 1 N.O. / 1N.C 75-97 IOL-150L-112-LK - 130 1 N.O. / 1N.C 90-112 IOL-150L-150-LK - 132 1 N.O. / 1N.C 100-150 IOL-150L-215-LK - 132 1 N.O. / 1N.C 140-215 IOL-180L-150-LK - 132 1 N.O. / 1N.C 100-150 IOL-180L-215-LK - 132 1 N.O. / 1N.C 140-215 IOL-300L-150-LK - 148 1 N.O. / 1N.C 100-150 IOL-300L-215-LK - 148 1 N.O. / 1N.C 140-215 IOL-300L-310-LK - 179 1 N.O. / 1N.C 200-310 IOL-300L-420-LK - 179 1 N.O. / 1N.C 275-420 Overload ccessories Separate Mount Block IH-SMB-32F 6 For & IOLS-25S IH-SMB-50F 8 For IOL-40S & IOLS-40S IH-SMB-80F 8 For IOL-80S & IOLS-80S IH-SMB-105F 10 For IOL-105L Lug Terminals IH-LUGS-215 22 For IOL-300L-150 & IOL-300L-215, 3 pack IH-LUGS-420 46 For IOL-300L-310 & IOL-300L-420, 3 pack IH-LUGSPCR 4 Spacers for IH-LUGS-215 & IH-LUGS-420 (required for UL) ICxxx-50S ICxxx-65S ICxxx-80S ICxxx-95S ICxxx-105S ICxxx-112L ICxxx-150L ICxxx-180L ICxxx-250L ICxxx-300L 130 separate mount block Lug Terminals IOL-150L

Standard Contactors & Overloads (cont d) 97 Contactor Dimension Legend in(mm) Overload Dimension Legend in(mm) W H D D H MOTOR CONTROLS Contactor Dimensions Contactor Frame Size Contactor Specifications Contactor ICxxx-09S ICxxx-12S ICxxx-18S ICxxx-25S ICxxx-32S ICxxx-40S ICxxx-50S ICxxx-65S ICxxx-80S ICxxx-95S ICxxx-105S Rated Insulation Voltage (V) UL/CS: 600, IEC/VDE 0660: 1000 Rated Impulse Voltage IEC60947-1 (kv) 6 6 6 6 6 6 8 8 8 8 8 Rated Operating Frequency (Hz) 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 Degree of Protection H W D in mm in mm in mm 18 (C) 3.189 81.0 1.772 45.0 3.362 85.4 18 (DC) 3.189 81.0 1.772 45.0 4.547 115.5 25 (C) 3.189 81.0 1.772 45.0 3.425 87.0 25 (DC) 3.189 81.0 1.772 45.0 4.606 117.0 40 (C) 3.524 89.5 2.165 55.5 3.852 97.9 40 (DC) 3.524 89.5 2.165 55.5 4.640 117.9 80 (C/DC) 4.58 116.3 2.60 66.0 4.53 115.0 105 (C/DC) 4.58 116.3 2.97 75.4 4.97 126.2 150 (C/DC) 6.3 160.0 4.8 121.5 5.7 145.0 180 (C/DC) 7.2 183.0 5.5 139.0 6.7 170.0 300 (C/DC) 7.8 198.0 5.8 147.5 7.1 181.0 Overload Dimensions Main Terminals IP20 IP20 IP20 IP10 IP10 IP10 IP10 IP10 IP10 IP10 IP10 Coil Terminals IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 uxiliary Terminals IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 IP20 Vibration Resistance Contactor Open (g) 3 3 3 4.5 7 7 4.5 4.5 4.5 5 5 (5 to 200Hz) Contactor Closed at (g) 6 6 6 5 9 9 9 9 9 7 7 Mechanical (Million C Coil Endurance ops) 10 10 10 10 10 10 10 10 10 10 10 Electrical Endurance C-3 (Million ops) 1.8 1.6 1.2 1.3 1.2 1.2 1.1 1.3 1.1 1.1 1.0 Shock Resistance: Contactor Open 8 8 8 8 7 7 6 6 6 6 6 1/2 Sin Wave = 11ms Contactor Closed at Coil 12 12 12 12 12 12 10 10 10 10 10 Terminal Capacity Stranded/Solid 1 or 2 1 or 2 1 or 2 1 or 2 (WG) (UL/CS) (14-10) (14-10) (14-10) (14-8) 14-8 14-8 14-1/0 14-1/0 14-1/0 14-1/0 14-1/0 Screw Driver Philips #2 Philips #2 Philips #2 Philips #2 Philips #2 Philips #2 5/32 5/32 5/32 5/32 5/32 Tightening Torque (lb-in) 15 15 15 16 22 22 40 40 40 60 60 mbient Temperature Storage: -67 to 176 F (-55 to 80 C), Operating (IEC) -13 to 131 F (-25 to 55 C) Environmental Climatic Withstand ccording to IEC 60680-2 Conditions Pollution Degree 3 Mounting 35mm DIN-rail cc. DIN EN 50 022 Weight (lbs) 0.65 0.65 0.65 0.65 1.15 1.19 2.44 2.47 2.49 3.20 3.24 Warranty 1 year Control Circuit Ratings (C/DC COIL) Standard Voltages 24 to 600VC / 24 to 500VDC 24 to 600 (C) / 24 to 240 24 to 600 (C) / 24 to 240 (DC) Monofrequency Coils (V) 0.85 to 1.1 (C) 0.85 to 1.1 (C) 0.85 to 1.1 (C) Coil Operating Limits Pick-up (V) 0.4 to 0.76 (C/DC) 0.5 to 0.8 (C/DC) 0.5 to 0.8 (C) / 0.7 to 0.8 (DC) Drop-out (V) 0.25 to 0.65 (C) / 0.15 to 0.4 (DC) 0.2 to 0.6 (C) / 0.4 to 0.6 0.2 to 0.6 (C) / 0.4 to 0.6 (DC) Coil Consumption Sealed (V) 4.0 to 7.2 (C) / 3.8 to 7.5 (DC) 9.2 to 12.5 (C) / 6.0 (DC) 16.5 to 25 (C) / 6.5 (DC) (Single Coils) Inrush (V) 70.0 (C) / 3.8 to 7.5 (DC) 115 (C) / 240 (DC) 295 (C) / 340 (DC) Heat Loss (W) 2.6 4.3 8.0 Power Factor Closed Cos Φ 0.28 0.34 0.32 Opened Cos Φ 0.85 0.69 0.54 Operating Time Coil Energization-N.O. (ms) 35 to 45 (DC) 50 to 60 (DC) 50 to 60 (DC) Coil De-energization-N.O. (ms) 7 to 12 (DC) 55 to 60 (DC) 55 to 60 (DC) Overload H W D in mm in mm in mm 2.0 51.5 1.8 45 3.3 82.5 IOL-40S/-80S 3.0 76.0 2.0 50.0 4.2 106.0 IOL-105S 3.9 99.5 3.0 75.0 3.9 98.5 IOL-150L-097-LK IOL-150L-112-LK IOL-150L-150-LK IOL-150L-215-LK 4.6 116.4 3.0 75.0 4.2 106.2 6.8 172.72 4.75 120.65 7.3 185.42 IOL-180L 6.8 172.72 4.75 120.65 7.3 185.42 IOL-300L 6.8 172.72 4.75 120.65 7.3 185.42 www.factorymation.com/motorcontrols ONLINE ORDERS FREESHIPPING SMLL PCKGES MIN. 29 500 LTL FREIGHT MIN. SEE INSIDE BCK COVER FOR MORE DETILS

98 Standard Contactors & Overloads (cont d) Contactor Specifications (cont d) Contactor ICxxx-112L ICxxx-150L ICxxx-180L ICxxx-250L ICxxx-300L Rated Insulation Voltage (V) UL/CS: 600, IEC/VDE 0660: 1000 Rated Impulse Voltage IEC60947-1 (kv) 8 8 8 8 8 Rated Operating Frequency (Hz) 25 to 400 25 to 400 25 to 400 25 to 400 25 to 400 Main Terminals IP00 IP00 IP00 IP00 IP00 Degree of Protection Coil Terminals IP20 IP20 IP20 IP20 IP20 uxiliary Terminals IP20 IP20 IP20 IP20 IP20 Vibration Resistance Contactor Open (g) 4 4 4 4 4 (5 to 200Hz) Contactor Closed at Coil (g) 4 4 4 4 4 Mechanical Endurance C Coil (Million ops) 10 10 10 10 10 Electrical Endurance C-3 (Million ops) 1.1 1.0 1.0 1.0 1.0 Shock Resistance (1/2 Sin Wave = 11ms) Terminal Capacity Overload IOL-40S/80S IOL-105S/150L IOL-300L Number of Poles 3 Rated Operation & Insulation Voltage IEC 60947-4-1 [V] 690 1000 UL; CS [V] 600 Rated Impulse Voltage [kv] 6 8 Tripping Class 10 Phase Failure Sensitivity Current mbient Temperature Contactor Open 3 3 3 3 3 Contactor Closed at Coil 3 3 3 3 3 Wires w/end Sleeve (WG) 1 x 300 or 2 x 107 1 x 300 or 2 x 107 1 x 300 or 2 x 107 1 x 500 or 2 x 300 1 x 500 or 2 x 300 Fine - Stranded w/sleeve (mm2) 2 x (25-70) 2 x (25-70) 2 x (50-120) 2 x (50-150) 2 x (50-150) Busbars (mm) 2 x (15x3) 2 x (15x3) 2 x (20x3) 2 x (30x5) 2 x (30x5) Screw Driver Philips #2 Philips #2 Philips #2 Philips #2 Philips #2 Tightening Torque (lb-in) 47.8-53.1 47.8-53.1 123.9-141.6 203.6-230.1 203.6-230.1 Environmental Conditions mbient Temperature Direct YES NO lternating [Hz] Up to 400 50/60 Storage Operating Storage: -67 to 176 F (-55 to 80 C), Operating (IEC) -13 to 131 F (-25 to 55 C) Climatic Withstand ccording to IEC 68-2 Pollution Degree 3 Mounting Screw to panel Weight (lbs) 0.65 0.65 0.65 0.65 1.15 Warranty Electronic Control Module Control Circuit Ratings (C/DC COIL) Standard Voltages (V) UL/CS: 600, IEC/VDE 0660: 1000 Coil Operating Limits YES -58 to 176 F (-50 to 80 C) -4 to 158 F (-20 to 70 C) Pollution Degree 3 Current Heat Loss [W] 3 5.5 5.5 15 Weight [lb] 0.32 0.68 1.00/1.45 3.95 Shock Resistance (IEC 60068-2-27; 1/2 Sine Wave) [g/ms] 10/11 Standards IEC 60947-1 / 60947-4-1, UL 508; CS C.22.2/14; VDE 0660/102 Power Terminals IP Rating IP10 IP00 Main Terminals Capacity Cross/Slotted Combination llen Head Slide Bar Stranded / Solid (UL/CS) 75 C, Cu Only [WG] 14-6 18-2 8-1/0 8-1/0 Tightening Torque [lb-in] 20 35 53 141 (100-215) 230 (200-420) 1 year Monofrequency Coils (V) 24 to 500 Pick-up (V) 0.65 to 1.1 Drop-out (V) 0.70 to 0.85 Coil Consumption Sealed (V) 0.40 to 0.60 (Single Coils) Inrush (V) 40 to 85 Heat Loss (W) 50 to 75 Coil Consumption Sealed (V/W) 14.8 (C) / 2.4 (DC) 14.8 (C) / 2.4 (DC) 14.1 (C) / 2.4 (DC) 14.1 (C) / 2.5 (DC) 14.1 (C) / 2.5 (DC) Inrush (V/W) 213 (C) / 166 (DC) 213 (C) / 166 (DC) 214 (C) / 154 (DC) 229 (C) / 171 (DC) 229 (C) / 171 (DC) Heat Loss (W) 3.9 (C) 2.4 (DC) 3.9 (C) 2.4 (DC) 3.8 (C) /2.4 (DC) 3.7 (C) /2.5 (DC) 3.7 (C) /2.5 (DC) Overload Specifications