Features. Applications

The new SemiQ Family of DC/DC converters from di/dt provides a high efficiency single output in a size that is only 6% of industry-standard quarter bricks, while preserving the same pinout and functionality. In high temperature environments, for output voltages ranging from 3.3 V to 1. V, the thermal performance of SemiQ converters exceeds that of most competitors' 2-3 A quarter bricks. This is accomplished through the use of patent pending circuit, packaging and processing techniques to achieve ultra-high efficiency, excellent thermal management and a very low body profile. Low body profile and the preclusion of heatsinks minimize airflow shadowing, thus enhancing cooling for downstream devices. The use of 1% automation for assembly, coupled with di/dt s advanced electric and thermal design, results in a product with extremely high reliability. Operating from a 36-7 V input, the SQ48 Series converters of the SemiQ Family provides any standard output voltage from 12 V down to 1. V. Outputs can be trimmed from 2% to +1% of the nominal output voltage (±1% for output voltages 1.2 V and 1. V), thus providing outstanding design flexibility. With a standard pinout and trim equations, the SQ48 Series converters are perfect drop-in replacements for existing quarter brick designs. Inclusion of this converter in new designs can result in significant board space and cost savings. The device is also available in a surface mount package. In both cases the designer can expect reliability improvement over other available converters because of the SQ48 Series optimized thermal efficiency. Applications Telecommunications Datacommunications Wireless Servers Features SQ48T and SQ48S Converters Delivers up to 1 A ( W) Industry-standard quarter brick pinout Extremely small footprint:.896 x 2.3 (2.6 in 2 ), 4% smaller than conventional quarter bricks For output voltages ranging from 3.3 to 1. V, higher current capability at elevated temperatures than most competitors' 2-3 A quarter bricks On-board input differential LC-filter Outputs available in 12., 8., 6.,., 3.3, 2., 2., 1.8, 1., 1.2 and 1. V High efficiency no heatsink required Start up into pre-biased output No minimum load required Available in through-hole and SM packages Lowest profile in industry:.26 (6.6 mm) Lowest weight in industry:.3 oz (1 g) Meets Basic Insulation requirements of EN69 Withstands 1 V input transient for 1 ms Fixed frequency operation Fully protected Remote output sense Output voltage trim range: +1%/ 2% with Industrystandard trim equations (except 1.2 and 1. V outputs with trim range ±1%) High reliability: MTBF of 3.4 million hours, calculated per Telcordia TR-332, Method I Case 1 Positive or negative logic ON/OFF option UL 69 recognized in US and Canada and DEMKO certified per IEC/EN 69 Meets conducted emissions requirements of FCC Class B and EN 22 Class B with external filter All materials meet UL94, V- flammability rating SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 1 of 7

Electrical Specifications (common to all versions) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, All output voltages, unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS ABSOLUTE MAXIMUM RATINGS Input Voltage Continuous 8 Vdc Operating Ambient Temperature -4 8 C Storage Temperature - 12 C INPUT CHARACTERISTICS Operating Input Voltage Range 36 48 7 Vdc Input Under Voltage Lockout Non-latching Turn-on Threshold 33 34 3 Vdc Turn-off Threshold 31 32 33 Vdc Input Voltage Transient 1 ms 1 Vdc ISOLATION CHARACTERISTICS I/O Isolation 2 Vdc Isolation Capacitance: 1. - 3.3 V 16 pf. - 6. V 26 pf 8. - 12 V 23 pf Isolation Resistance 1 MΩ FEATURE CHARACTERISTICS Switching Frequency 41 khz Output Voltage Trim Range 1 Industry-std. equations (1. - 12 V ) -2 +1 % Use trim equations on Page 4 (1. - 1.2 V) -1 +1 % Remote Sense Compensation 1 Percent of V OUT (NOM) +1 % Output Over-Voltage Protection Non-latching (1. - 12 V) 117 122 127 % Non-latching (1. - 1.2 V) 124 132 14 % Auto-Restart Period Applies to all protection features 1 ms Turn-On Time 4 ms ON/OFF Control (Positive Logic) Converter Off -2.8 Vdc Converter On 2.4 2 Vdc ON/OFF Control (Negative Logic) Converter Off 2.4 2 Vdc Converter On -2.8 Vdc Additional Notes: 1. Vout can be increased up to 1% via the sense leads or up to 1% via the trim function, however total output voltage trim from all sources should not exceed 1% of V OUT (NOM), in order to insure specified operation of over-voltage protection circuitry. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 2 of 7

Operation Input and Output Impedance These power converters have been designed to be stable with no external capacitors when used in low inductance input and output circuits. However, in many applications, the inductance associated with the distribution from the power source to the input of the converter can affect the stability of the converter. The addition of a 33 µf electrolytic capacitor with an ESR < 1 Ω across the input helps ensure stability of the converter. In many applications, the user has to use decoupling capacitance at the load. The power converter will exhibit stable operation with external load capacitance up to 1 µf on 12 V, 2,2µF on 8. V, 1, µf on. 6. V, and 1, µf on 3.3 1. V outputs. be used to drive the input of the ON/OFF pin. The device must be capable of sinking up to.2 ma at a low level voltage of.8 V. An external voltage source of ±2 V max. may be connected directly to the ON/OFF input, in which case it should be capable of sourcing or sinking up to 1 ma depending on the signal polarity. See the Start-up Information section for system timing waveforms associated with use of the ON/OFF pin. Remote Sense (Pins and 7) The remote sense feature of the converter compensates for voltage drops occurring between the output pins of the converter and the load. The SENSE(-) (Pin ) and SENSE(+) (Pin 7) pins should be connected at the load or at the point where regulation is required (see Fig. B). ON/OFF (Pin 2) The ON/OFF pin is used to turn the power converter on or off remotely via a system signal. There are two remote control options available, positive logic and negative logic and both are referenced to Vin(-). Typical connections are shown in Fig. A. Vin Vin (+) ON/OFF Vin (-) TM SemiQ Family Converter Vout (+) 1 SENSE (+) (Top View) TRIM SENSE (-) 1 Vout (-) Rw Rw Rload Vin CONTROL INPUT Vin (+) ON/OFF Vin (-) TM SemiQ Family Converter (Top View) Vout (+) SENSE (+) TRIM SENSE (-) Vout (-) Fig. A: Circuit configuration for ON/OFF function. The positive logic version turns on when the ON/OFF pin is at logic high and turns off when at logic low. The converter is on when the ON/OFF pin is left open. The negative logic version turns on when the pin is at logic low and turns off when the pin is at logic high. The ON/OFF pin can be hard wired directly to Vin(-) to enable automatic power up of the converter without the need of an external control signal. ON/OFF pin is internally pulled-up to V through a resistor. A mechanical switch, open collector transistor, or FET can Rload Fig. B: Remote sense circuit configuration. If remote sensing is not required, the SENSE(-) pin must be connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin must be connected to the Vout(+) pin (Pin 8) to ensure the converter will regulate at the specified output voltage. If these connections are not made, the converter will deliver an output voltage that is slightly higher than the specified value. Because the sense leads carry minimal current, large traces on the end-user board are not required. However, sense traces should be located close to a ground plane to minimize system noise and insure optimum performance. When wiring discretely, twisted pair wires should be used to connect the sense lines to the load to reduce susceptibility to noise. The converter s output over-voltage protection (OVP) senses the voltage across Vout(+) and Vout(-), and not across the sense lines, so the resistance (and resulting voltage drop) between the output pins of the converter and the load should be minimized to prevent unwanted triggering of the OVP. When utilizing the remote sense feature, care must be taken not to exceed the maximum allowable output power capabil- SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 3 of 7

ity of the converter, equal to the product of the nominal output voltage and the allowable output current for the given conditions. When using remote sense, the output voltage at the converter can be increased by as much as 1% above the nominal rating in order to maintain the required voltage across the load. Therefore, the designer must, if necessary, decrease the maximum current (originally obtained from the derating curves) by the same percentage to ensure the converter s actual output power remains at or below the maximum allowable output power. Output Voltage Adjust /TRIM (Pin 6) The converter s output voltage can be adjusted up 1% or down 2% for Vout 1. V, and ±1% for Vout = 1.2 V and 1. V relative to the rated output voltage by the addition of an externally connected resistor. For output voltage 3.3 V, trim up to 1% is guaranteed only at Vin 4 V, and it is marginal (8% to 1%) at Vin = 36 V. The TRIM pin should be left open if trimming is not being used. To minimize noise pickup, a.1 µf capacitor is connected internally between the TRIM and SENSE(-) pins. To increase the output voltage, refer to Fig. C. A trim resistor, R T-INCR, should be connected between the TRIM (Pin 6) and SENSE(+) (Pin 7), with a value of:.11(1 + )VO NOM 626 RT INCR = 1.22 [kω] (1. 12 V) 1.22 84.6 = 7.2 [kω] (1.2 V) RT INCR 12 RT INCR = 9 [kω] (1. V) where, RT INCR VO NOM = = Required value of trim-up resistor kω] Nominal value of output voltage [V] (VO-REQ VO-NOM) = X 1 [%] VO -NOM VO REQ = Desired (trimmed) output voltage [V]. When trimming up, care must be taken not to exceed the converter s maximum allowable output power. See previous section for a complete discussion of this requirement. Vin Vin (+) ON/OFF Vin (-) TM SemiQ Family Converter (Top View) Vout (+) SENSE (+) TRIM SENSE (-) Vout (-) R T-INCR Fig. C: Configuration for increasing output voltage. To decrease the output voltage (Fig. D), a trim resistor, R T-DECR, should be connected between the TRIM (Pin 6) and SENSE(-) (Pin ), with a value of: 11 = 1.22 [kω] (1. 12 V) RT DECR 7 = 1 [kω] (1.2 V) RT DECR 7 RT DECR = 17 [kω] (1. V) where, RT DECR = Required value of trim-down resistor [kω] and is as defined above. Note: The above equations for calculation of trim resistor values match those typically used in conventional industrystandard quarter bricks and one-eighth bricks (except for 1.2 V and 1. V outputs). Converters with output voltages 1.2 V and 1. V are available with alternative trim feature to provide the customers with the flexibility of second sourcing. For these converters, the last character in the part number is T. The trim equations of T version of converters and more information can be found in Application Note 13. Vin Vin (+) ON/OFF Vin (-) TM SemiQ Family Converter (Top View) Vout (+) SENSE (+) TRIM SENSE (-) Vout (-) RT-DECR Fig. D: Configuration for decreasing output voltage. Rload Rload SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 4 of 7

Trimming/sensing beyond 11% of the rated output voltage is not an acceptable design practice, as this condition could cause unwanted triggering of the output over-voltage protection (OVP) circuit. The designer should ensure that the difference between the voltages across the converter s output pins and its sense pins does not exceed 1% of V OUT (NOM), or: [VOUT( + ) VOUT( )] [VSENSE( + ) VSENSE( )] VO - NOM X1% [V] This equation is applicable for any condition of output sensing and/or output trim. Protection Features Input Under-Voltage Lockout Input under-voltage lockout is standard with this converter. The converter will shut down when the input voltage drops below a pre-determined voltage. The input voltage must be at least 3 V for the converter to turn on. Once the converter has been turned on, it will shut off when the input voltage drops below 31 V. This feature is beneficial in preventing deep discharging of batteries used in telecom applications. Output Over-Current Protection (OCP) The converter is protected against over-current or short circuit conditions. Upon sensing an over-current condition, the converter will switch to constant current operation and thereby begin to reduce output voltage. When the output voltage drops below % of the nominal value of output voltage, the converter will shut down (Fig. x.17). Once the converter has shut down, it will attempt to restart nominally every 1 ms with a typical 1-2% duty cycle (Fig. x.18). The attempted restart will continue indefinitely until the overload or short circuit conditions are removed or the output voltage rises above % of its nominal value. Output Over-Voltage Protection (OVP) The converter will shut down if the output voltage across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds the threshold of the OVP circuitry. The OVP circuitry contains its own reference, independent of the output voltage regulation loop. Once the converter has shut down, it will attempt to restart every 1 ms until the OVP condition is removed. Over-Temperature Protection (OTP) The converter will shut down under an over-temperature condition to protect itself from overheating caused by operation outside the thermal derating curves, or operation in abnormal conditions such as system fan failure. After the converter has cooled to a safe operating temperature, it will automatically restart. Safety Requirements The converters meet North American and International safety regulatory requirements per UL69 and EN69. Basic Insulation is provided between input and output. To comply with safety agencies requirements, an input line fuse must be used external to the converter. The Table below provides the recommended fuse rating for use with this family of products. Output Voltage Fuse Rating 3.3 V 4-A 12 -. V, 2. V 3-A 2. - 1. V 2-A If one input fuse is used for a group of modules, the maximum fuse rating should not exceed 1-A (SQ modules are UL approved with up to a 1-A fuse). Electromagnetic Compatibility (EMC) EMC requirements must be met at the end-product system level, as no specific standards dedicated to EMC characteristics of board mounted component dc-dc converters exist. However, di/dt tests its converters to several system level standards, primary of which is the more stringent EN22, Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement. With the addition of a simple external filter (see application notes), all versions of the SQ Series of converters pass the requirements of Class B conducted emissions per EN22 and FCC, and meet at a minimum, Class A radiated emissions per EN 22 and Class B per FCC Title 47CFR, Part 1-J. Please contact di/dt Applications Engineering for details of this testing. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page of 7

Characterization General Information The converter has been characterized for many operational aspects, to include thermal derating (maximum load current as a function of ambient temperature and airflow) for vertical and horizontal mounting, efficiency, start-up and shutdown parameters, output ripple and noise, transient response to load step-change, overload and short circuit. The figures are numbered as Fig. x.y, where x indicates the different output voltages, and y is associated with a specific plot (y = 1 for the vertical thermal derating, ). For example, Fig. x.1 will refer to the vertical thermal derating for all the output voltages in general. The following pages contain specific plots or waveforms associated with the converter. Additional comments for specific data are provided below. Test Conditions All data presented were taken with the converter soldered to a test board, specifically a.6 thick printed wiring board (PWB) with four layers. The top and bottom layers were not metalized. The two inner layers, comprising two-ounce copper, were used to provide traces for connectivity to the converter. The lack of metalization on the outer layers as well as the limited thermal connection ensured that heat transfer from the converter to the PWB was minimized. This provides a worst-case but consistent scenario for thermal derating purposes. All measurements requiring airflow were made in di/dt s vertical and horizontal wind tunnel facilities using Infrared (IR) thermography and thermocouples for thermometry. Ensuring components on the converter do not exceed their ratings is important to maintaining high reliability. If one anticipates operating the converter at or close to the maximum loads specified in the derating curves, it is prudent to check actual operating temperatures in the application. Thermographic imaging is preferable; if this capability is not available, then thermocouples may be used. di/dt recommends the use of AWG #4 gauge thermocouples to ensure measurement accuracy. Careful routing of the thermocouple leads will further minimize measurement error. Refer to Figure H for optimum measuring thermocouple location. Thermal Derating Load current vs. ambient temperature and airflow rates are given in Fig. x.1 to Fig. x.4 for through-hole and surface mount version. Ambient temperature was varied between 2 C and 8 C, with airflow rates from 3 to LFM (.1 to 2. m/s), and vertical and horizontal converter mounting. For each set of conditions, the maximum load current was defined as the lowest of: (i) The output current at which either any FET junction temperature did not exceed a maximum specified temperature (12 C) as indicated by the thermographic image, or (ii) The nominal rating of the converter (4 A on 12 V,.3 A on 8. V, 8 A on 6. V, 1 A on. V, and 1 A on 3.3 1. V). During normal operation, derating curves with maximum FET temperature less than or equal to 12 C should not be exceeded. Temperature on the PCB at the thermocouple location shown in Fig. H should not exceed 118 C in order to operate inside the derating curves. Efficiency Fig. x. shows the efficiency vs. load current plot for ambient temperature of 2ºC, airflow rate of 3 LFM (1. m/s) with vertical mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of efficiency vs. load current, as a function of ambient temperature with Vin = 48 V, airflow rate of 2 LFM (1 m/s) with vertical mounting is shown in Fig. x.6. Power Dissipation Fig. x.7 shows the power dissipation vs. load current plot for Ta = 2ºC, airflow rate of 3 LFM (1. m/s) with vertical mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of power dissipation vs. load current, as a function of ambient temperature with Vin = 48 V, airflow rate of 2 LFM (1 m/s) with vertical mounting is shown in Fig. x.8. Start-up Output voltage waveforms, during the turn-on transient using the ON/OFF pin for full rated load currents (resistive load) are shown without and with external load capacitance in Fig. x.9 and Fig. x.1, respectively. Ripple and Noise Fig. x.13 shows the output voltage ripple waveform, measured at full rated load current with a 1 µf tantalum and 1 µf ceramic capacitor across the output. Note that all output SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 6 of 7

voltage waveforms are measured across a 1 µf ceramic capacitor. The input reflected ripple current waveforms are obtained using the test setup shown in Fig x.14. The corresponding waveforms are shown in Fig. x.1 and Fig. x.16. Start-up Information (using negative ON/OFF) Scenario #1: Initial Start-up From Bulk Supply ON/OFF function enabled, converter started via application of V IN. See Figure E. Time Comments t ON/OFF pin is ON; system front end power is toggled on, V IN to converter begins to rise. t 1 V IN crosses Under-Voltage Lockout protection circuit threshold; converter enabled. t 2 Converter begins to respond to turn-on command (converter turn-on delay). t 3 Converter V OUT reaches 1% of nominal value. For this example, the total converter start-up time (t 3 - t 1 ) is typically 4 ms. V IN ON/OFF STATE V OUT VIN OFF ON t t1 t2 t3 Fig. E: Start-up scenario #1 t Scenario #2: Initial Start-up Using ON/OFF Pin With V IN previously powered, converter started via ON/OFF pin. See Figure F. Time Comments t V INPUT at nominal value. t 1 Arbitrary time when ON/OFF pin is enabled (converter enabled). t 2 End of converter turn-on delay. t 3 Converter V OUT reaches 1% of nominal value. For this example, the total converter start-up time (t 3 - t 1 ) is typically 4 ms. Scenario #3: Turn-off and Restart Using ON/OFF Pin With V IN previously powered, converter is disabled and then enabled via ON/OFF pin. See Figure G. Time Comments t V IN and V OUT are at nominal values; ON/OFF pin ON. t 1 ON/OFF pin arbitrarily disabled; converter output falls to zero; turn-on inhibit delay period (1 ms typical) is initiated, and ON/OFF pin action is internally inhibited. t 2 ON/OFF pin is externally re-enabled. If (t 2 - t 1 ) 1 ms, external action of ON/OFF pin is locked out by start-up inhibit timer. If (t 2 - t 1 ) > 1 ms, ON/OFF pin action is internally enabled. t 3 Turn-on inhibit delay period ends. If ON/OFF pin is ON, converter begins turn-on; if off, converter awaits ON/OFF pin ON signal; see Figure F. t 4 End of converter turn-on delay. t Converter V OUT reaches 1% of nominal value. For the condition, (t 2 - t 1 ) 1 ms, the total converter start-up time (t - t 2 ) is typically 14 ms. For (t 2 - t 1 ) > 1 ms, start-up will be typically 4 ms after release of ON/OFF pin. ON/OFF STATE VOUT VIN ON/OFF STATE VOUT t OFF ON OFF ON t1 t t1 t2 t3 Fig. F: Start-up scenario #2. t2 1 ms t3 t4 Fig. G: Start-up scenario #3. t t t SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 7 of 7

Electrical Specifications: SQ48T/S412 (12 Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=12 Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 4 Adc, 12 Vdc Out @ 36 Vdc In 1.3 Adc Input Stand-by Current Vin = 48 V, converter disabled 3 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 4 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 11.88 12. 12.12 Vdc Output Regulation Over Line ±4 ±1 mv Over Load ±4 ±1 mv Output Voltage Range Over line, load and temperature 2 11.82 12.18 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 8 12 mv PK-PK External Load Capacitance Plus full load (resistive) 1 µf Output Current Range 4 Adc Current Limit Inception Non-latching 4.. Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 7. 1 A RMS Short-Circuit Current Non-latching 4 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 2 mv di/dt = A/µS Co = 47 µf tant. + 1 µf ceramic 2 mv Setting Time to 1% 4 µs EFFICIENCY 1% Load 87 % % Load 87 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 8 of 7

SQ48T/S412 (12 Volts Out) 4 4 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 12V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T412 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 12V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T412 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 4 4 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 12V.3: Available load current vs. ambient temperature and airflow rates for SQ48S412 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 12V.4: Available load current vs. ambient temperature and airflow rates for SQ48S412 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 9 of 7

SQ48T/S412 (12 Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 1 2 3 4 Fig. 12V.: Efficiency vs. load current and input voltage for SQ48T/S412 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 1 2 3 4 Fig. 12V.6: Efficiency vs. load current and ambient temperature for SQ48T/S412 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 1. 1. 8. 8. Power Dissipation [W] 6. 4. 2. 72 V 48 V 36 V Power Dissipation [W] 6. 4. 2. 7 C C 4 C. 1 2 3 4 Fig. 12V.7: Power dissipation vs. load current and input voltage for SQ48T/S412 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 1 2 3 4 Fig. 12V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S412 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 1 of 7

SQ48T/S412 (12 Volts Out) Fig. 12V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage ( V/div.). Time scale: 1 ms/div. Fig. 12V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage ( V/div.). Time scale: 2 ms/div. Fig. 12V.11: Output voltage response to load current stepchange (1 A 2 A 1 A) at Vin = 48 V. Top trace: output voltage (2 mv/div.). Bottom trace: load current (1 A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:. ms/div. Fig. 12V.12: Output voltage response to load current stepchange (1 A 2 A 1 A) at Vin = 48 V. Top trace: output voltage (2 mv/div.). Bottom trace: load current (1 A/div.). Current slew rate: A/µs. Co = 47 µf tantalum + 1 µf ceramic. Time scale:. ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 11 of 7

SQ48T/S412 (12 Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 12V.13: Output voltage ripple ( mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 12V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 12V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 12V.14 for test setup. Time scale: 1 µs/div. Fig. 12V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 12V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 12 of 7

SQ48T/S412 (12 Volts Out) 1 1 Vout [Vdc] 1 2 3 4 6 Iout [Adc] Fig. 12V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 12V.18: Load current (top trace, A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace ( A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 13 of 7

Electrical Specifications: SQ48T/S8 (8. Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=8. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current.3 Adc, 8. Vdc Out @ 36 Vdc In 1.38 Adc Input Stand-by Current Vin = 48 V, converter disabled 3 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 33 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 7.92 8. 8.8 Vdc Output Regulation Over Line ±4 ±1 mv Over Load ±4 ±1 mv Output Voltage Range Over line, load and temperature 2 7.88 8.12 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 7 1 mv PK-PK External Load Capacitance Plus full load (resistive) 22 µf Output Current Range.3 Adc Current Limit Inception Non-latching.7 6.2 6.7 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 1 12 A RMS Short-Circuit Current Non-latching 4 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 16 mv di/dt = A/µS Co = 94 µf tant. + 1 µf ceramic 16 mv Setting Time to 1% 4 µs EFFICIENCY 1% Load 8. % % Load 87 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 14 of 7

SQ48T/S8 (8. Volts Out) 6 6 4 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 4 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 8.V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T8 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 8.V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T8 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 6 6 4 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 4 3 2 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 8.V.3: Available load current vs. ambient temperature and airflow rates for SQ48S8 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 8.V.4: Available load current vs. ambient temperature and airflow rates for SQ48S8 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 1 of 7

SQ48T/S8 (8. Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 1 2 3 4 6 Fig. 8.V.: Efficiency vs. load current and input voltage for SQ48T/S8 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 1 2 3 4 6 Fig. 8.V.6: Efficiency vs. load current and ambient temperature for SQ48T/S8 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 1. 1. 8. 8. Power Dissipation [W] 6. 4. 2. 72 V 48 V 36 V Power Dissipation [W] 6. 4. 2. 7 C C 4 C. 1 2 3 4 6 Fig. 8.V.7: Power dissipation vs. load current and ambient temperature for SQ48T/S8 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 1 2 3 4 6 Fig. 8.V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S8 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 16 of 7

SQ48T/S8 (8. Volts Out) Fig. 8.V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (2V/div.). Time scale: 1 ms/div. Fig. 8.V.1: Turn-on transient at full rated load current (resistive) plus 2,2 µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (2 V/div.). Time scale: 2 ms/div. Fig. 8.V.11: Output voltage response to load current stepchange (1.32 A 2.6 A 1.32 A) at Vin = 48 V. Top trace: output voltage (2 mv/div.). Bottom trace: load current (1 A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:. ms/div. Fig. 8.V.12: Output voltage response to load current stepchange (1.32 A 2.6 A 1.32 A) at Vin = 48 V. Top trace: output voltage (2 mv/div.). Bottom trace: load current (1 A/div.). Current slew rate: A/µs. Co = 94 µf tantalum + 1 µf ceramic. Time scale:. ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 17 of 7

SQ48T/S8 (8. Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 8.V.13: Output voltage ripple ( mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 8.V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 8.V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 8.V.14 for test setup. Time scale: 1 µs/div. Fig. 8.V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 8.V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 18 of 7

SQ48T/S8 (8. Volts Out) 12 8 Vout [Vdc] 4 2 4 6 8 Iout [Adc] Fig. 8.V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 8.V.18: Load current (top trace, A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace ( A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 19 of 7

Electrical Specifications: SQ48T/S86 (6. Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=6. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 8 Adc, 6. Vdc Out @ 36 Vdc In 1. Adc Input Stand-by Current Vin = 48 V, converter disabled 3 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 4 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load).94 6. 6.6 Vdc Output Regulation Over Line ±2 ± mv Over Load ±2 ± mv Output Voltage Range Over line, load and temperature 2.91 6.9 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 4 6 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 8 Adc Current Limit Inception Non-latching 9 1 11. Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 1 2 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 1 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 8 mv Setting Time to 1% 2 µs EFFICIENCY 1% Load 89 % % Load 89 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 2 of 7

SQ48T/S86 (6. Volts Out) 1 1 8 8 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 6.V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T86 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 6.V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T86 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 1 1 8 8 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 6.V.3: Available load current vs. ambient temperature and airflow rates for SQ48S86 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 6.V.4: Available load current vs. ambient temperature and airflow rates for SQ48S86 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 21 of 7

SQ48T/S86 (6. Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 Fig. 6.V.: Efficiency vs. load current and input voltage for SQ48T/S86 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 Fig. 6.V.6: Efficiency vs. load current and ambient temperature for SQ48T/S86 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 1. 1. 8. 8. Power Dissipation [W] 6. 4. 2. 72 V 48 V 36 V Power Dissipation [W] 6. 4. 2. 7 C C 4 C. 2 4 6 8 1 Fig. 6.V.7: Power dissipation vs. load current and ambient temperature for SQ48T/S86 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 Fig. 6.V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S86 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 22 of 7

SQ48T/S86 (6. Volts Out) Fig. 6.V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (2 V/div.). Time scale: 2 ms/div. Fig. 6.V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (2 V/div.). Time scale: ms/div. Fig. 6.V.11: Output voltage response to load current stepchange (2 A 4 A 2 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current (2 A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 6.V.12: Output voltage response to load current stepchange (2 A 4 A 2 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current (2 A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 23 of 7

SQ48T/S86 (6. Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 6.V.13: Output voltage ripple ( mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 6.V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 6.V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 6.V.14 for test setup. Time scale: 1 µs/div. Fig. 6.V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 6.V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 24 of 7

SQ48T/S86 (6. Volts Out) 8 6 Vout [Vdc] 4 2 3 6 9 12 Iout [Adc] Fig. 6.V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 6.V.18: Load current (top trace, 1 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (1 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 2 of 7

Electrical Specifications: SQ48T/S1 (. Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc,. Vdc Out @ 36 Vdc In 1.6 Adc Input Stand-by Current Vin = 48 V, converter disabled 2.6 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 4 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 4.9.. Vdc Output Regulation Over Line ±2 ± mv Over Load ±2 ± mv Output Voltage Range Over line, load and temperature 2 4.92.7 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 4 8 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 11 12. 14 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 2 3 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 2 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 18 mv Setting Time to 1% 4 µs EFFICIENCY 1% Load 87 % % Load 88 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 26 of 7

SQ48T/S1 (. Volts Out) 12 12 1 1 8 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 8 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig..V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T1 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig..V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T1 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 12 12 1 1 8 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 8 6 4 2 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig..V.3: Available load current vs. ambient temperature and airflow rates for SQ48S1 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig..V.4: Available load current vs. ambient temperature and airflow rates for SQ48S1 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 27 of 7

SQ48T/S1 (. Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 Fig..V.: Efficiency vs. load current and input voltage for SQ48T/S1 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 12 Fig..V.6: Efficiency vs. load current and ambient temperature for SQ48T/S1 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 1. 1. 8. 8. Power Dissipation [W] 6. 4. 2. 72 V 48 V 36 V Power Dissipation [W] 6. 4. 2. 7 C C 4 C. 2 4 6 8 1 12 Fig..V.7: Power dissipation vs. load current and input voltage for SQ48T/S1 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 Fig..V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S1 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 28 of 7

SQ48T/S1 (. Volts Out) Fig..V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (2 V/div.). Time scale: 2 ms/div. Fig..V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (2 V/div.). Time scale: 2 ms/div. Fig..V.11: Output voltage response to load current stepchange (2. A A 2. A) at Vin = 48 V. Top trace: output voltage (2 mv/div.). Bottom trace: load current (2 A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig..V.12: Output voltage response to load current stepchange (2. A A 2. A) at Vin = 48 V. Top trace: output voltage (2 mv/div.). Bottom trace: load current (2 A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 29 of 7

SQ48T/S1 (. Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig..V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig..V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig..V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig..V.14 for test setup. Time scale: 1 µs/div. Fig..V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig..V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 3 of 7

SQ48T/S1 (. Volts Out) 6 4 Vout [Vdc] 3 2 1 1 1 Iout [Adc] Fig..V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig..V.18: Load current (top trace, 1 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (1 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 31 of 7

Electrical Specifications: SQ48T/S133 (3.3 Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=3.3 Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 3.3 Vdc Out @ 36 Vdc In 1.6 Adc Input Stand-by Current Vin = 48 V, converter disabled 2.6 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 42 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 3.267 3.3 3.333 Vdc Output Regulation Over Line ±2 ± mv Over Load ±2 ± mv Output Voltage Range Over line, load and temperature 2 3.2 3.3 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 9 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 1 mv Setting Time to 1% 1 µs EFFICIENCY 1% Load 89. % % Load 89. % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 32 of 7

SQ48T/S133 (3.3 Volts Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 3.3V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T133 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 3.3V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T133 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 3.3V.3: Available load current vs. ambient temperature and airflow rates for SQ48S133 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 3.3V.4: Available load current vs. ambient temperature and airflow rates for SQ48S133 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 33 of 7

SQ48T/S133 (3.3 Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16 Fig. 3.3V.: Efficiency vs. load current and input voltage for SQ48T/S133 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 12 14 16 Fig. 3.3V.6: Efficiency vs. load current and ambient temperature for SQ48T/S133 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 8. 8. Power Dissipation [W] 6. 4. 2. 72 V 48 V 36 V Power Dissipation [W] 6. 4. 2. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 3.3V.7: Power dissipation vs. load current and input voltage for SQ48T/S133 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 3.3V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S133 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 34 of 7

SQ48T/S133 (3.3 Volts Out) Fig. 3.3V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 3.3V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 3.3V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 3.3V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 3 of 7

SQ48T/S133 (3.3 Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 3.3V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 3.3V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 3.3V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 3.3V.14 for test setup. Time scale: 1 µs/div. Fig. 3.3V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 3.3V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 36 of 7

SQ48T/S133 (3.3 Volts Out) 4 3 Vout [Vdc] 2 1 1 1 2 Iout [Adc] Fig. 3.3V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 3.3V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 37 of 7

Electrical Specifications: SQ48T/S12 (2. Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=2. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 2. Vdc Out @ 36 Vdc In 1.2 Adc Input Stand-by Current Vin = 48 V, converter disabled 2.6 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 34 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 2.47 2. 2.2 Vdc Output Regulation Over Line ±2 ± mv Over Load ±2 ± mv Output Voltage Range Over line, load and temperature 2 2.462 2.38 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic) 12 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 12 mv Setting Time to 1% 1 µs EFFICIENCY 1% Load 87 % % Load 87. % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 38 of 7

SQ48T/S12 (2. Volts Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 2.V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T12 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 2.V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T12 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 2.V.3: Available load current vs. ambient temperature and airflow rates for SQ48S12 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 2.V.4: Available load current vs. ambient temperature and airflow rates for SQ48S12 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 39 of 7

SQ48T/S12 (2. Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16 Fig. 2.V.: Efficiency vs. load current and input voltage for SQ48T/S12 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 12 14 16 Fig. 2.V.6: Efficiency vs. load current and ambient temperature for SQ48T/S12 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 8. 8. Power Dissipation [W] 6. 4. 2. 72 V 48 V 36 V Power Dissipation [W] 6. 4. 2. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 2.V.7: Power dissipation vs. load current and input voltage for SQ48T/S12 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 2.V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S12 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 4 of 7

SQ48T/S12 (2. Volts Out) Fig. 2.V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 2.V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 2.V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 2.V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 41 of 7

SQ48T/S12 (2. Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 2.V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 2.V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 2.V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 2.V.14 for test setup. Time scale: 1 µs/div. Fig. 2.V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 2.V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 42 of 7

SQ48T/S12 (2. Volts Out) 3 Vout [Vdc] 2 1 1 1 2 Iout [Adc] Fig. 2.V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 2.V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 43 of 7

Electrical Specifications: SQ48T/S12 (2. Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=2. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 2. Vdc Out @ 36 Vdc In 1. Adc Input Stand-by Current Vin = 48 V, converter disabled 3 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 31 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 1.98 2. 2.2 Vdc Output Regulation Over Line ±2 ± mv Over Load ±2 ± mv Output Voltage Range Over line, load and temperature 2 1.97 2.3 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 8 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 6 mv Setting Time to 1% 6 µs EFFICIENCY 1% Load 86. % % Load 87 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 44 of 7

SQ48T/S12 (2. Volts Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 2.V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T12 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 2.V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T12 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 2.V.3: Available load current vs. ambient temperature and airflow rates for SQ48S12 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 2.V.4: Available load current vs. ambient temperature and airflow rates for SQ48S12 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 4 of 7

SQ48T/S12 (2. Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16 Fig. 2.V.: Efficiency vs. load current and input voltage for SQ48T/S12 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 12 14 16 Fig. 2.V.6: Efficiency vs. load current and ambient temperature for SQ48T/S12 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 6. 6... Power Dissipation [W] 4. 3. 2. 1. 72 V 48 V 36 V Power Dissipation [W] 4. 3. 2. 1. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 2.V.7: Power dissipation vs. load current and input voltage for SQ48T/S12 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 2.V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S12 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 46 of 7

SQ48T/S12 (2. Volts Out) Fig. 2.V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 2.V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 2.V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 2.V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 47 of 7

SQ48T/S12 (2. Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 2.V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 2.V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 2.V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 2.V.14 for test setup. Time scale: 1 µs/div. Fig. 2.V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 2.V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 48 of 7

SQ48T/S12 (2. Volts Out) 3 Vout [Vdc] 2 1 1 1 2 Iout [Adc] Fig. 2.V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 2.V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 49 of 7

Electrical Specifications: SQ48T/S118 (1.8 Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=1.8 Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 1.8 Vdc Out @ 36 Vdc In.9 Adc Input Stand-by Current Vin = 48 V, converter disabled 2.6 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 29 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 1.782 1.8 1.818 Vdc Output Regulation Over Line ±2 ±4 mv Over Load ±2 ± mv Output Voltage Range Over line, load and temperature 2 1.773 1.827 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 8 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 1 mv Setting Time to 1% 1 µs EFFICIENCY 1% Load 8. % % Load 86 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page of 7

SQ48T/S118 (1.8 Volts Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.8V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T118 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.8V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T118 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.8V.3: Available load current vs. ambient temperature and airflow rates for SQ48S118 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.8V.4: Available load current vs. ambient temperature and airflow rates for SQ48S118 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 1 of 7

SQ48T/S118 (1.8 Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16 Fig. 1.8V.: Efficiency vs. load current and input voltage for SQ48T/S118 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 12 14 16 Fig. 1.8V.6: Efficiency vs. load current and ambient temperature for SQ48T/S118 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 6. 6... Power Dissipation [W] 4. 3. 2. 1. 72 V 48 V 36 V Power Dissipation [W] 4. 3. 2. 1. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 1.8V.7: Power dissipation vs. load current and input voltage for SQ48T/S118 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 1.8V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S118 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 2 of 7

SQ48T/S118 (1.8 Volts Out) Fig. 1.8V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 1.8V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 1.8V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 1.8V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 3 of 7

SQ48T/S118 (1.8 Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 1.8V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 1.8V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 1.8V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.8V.14 for test setup. Time scale: 1 µs/div. Fig. 1.8V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.8V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 4 of 7

SQ48T/S118 (1.8 Volts Out) 3 Vout [Vdc] 2 1 1 1 2 Iout [Adc] Fig. 1.8V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.8V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page of 7

Electrical Specifications: SQ48T/S11 (1. Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=1. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 1. Vdc Out @ 36 Vdc In.7 Adc Input Stand-by Current Vin = 48 V, converter disabled 2.6 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 2 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 1.48 1. 1.1 Vdc Output Regulation Over Line ±2 ±4 mv Over Load ±2 ±4 mv Output Voltage Range Over line, load and temperature 2 1.477 1.23 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 8 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 12 mv Setting Time to 1% 1 µs EFFICIENCY 1% Load 84. % % Load 8 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 6 of 7

SQ48T/S11 (1. Volts Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T11 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T11 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.V.3: Available load current vs. ambient temperature and airflow rates for SQ48S11 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.V.4: Available load current vs. ambient temperature and airflow rates for SQ48S11 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 7 of 7

SQ48T/S11 (1. Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16 Fig. 1.V.: Efficiency vs. load current and input voltage for SQ48T/S11 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C..6 2 4 6 8 1 12 14 16 Fig. 1.V.6: Efficiency vs. load current and ambient temperature for SQ48T/S11 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 6. 6... Power Dissipation [W] 4. 3. 2. 1. 72 V 48 V 36 V Power Dissipation [W] 4. 3. 2. 1. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 1.V.7: Power dissipation vs. load current and input voltage for SQ48T/S11 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 1.V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S11 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 8 of 7

SQ48T/S11 (1. Volts Out) Fig. 1.V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (. V/div.). Time scale: 2 ms/div. Fig. 1.V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (. V/div.). Time scale: 2 ms/div. Fig. 1.V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 1.V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 9 of 7

SQ48T/S11 (1. Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 1.V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 1.V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 1.V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.V.14 for test setup. Time scale: 1 µs/div. Fig. 1.V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 6 of 7

SQ48T/S11 (1. Volts Out) 2. 1. Vout [Vdc] 1.. 1 1 2 Iout [Adc] Fig. 1.V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 61 of 7

Electrical Specifications: SQ48T/S112 (1.2 Volts Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=1.2 Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 1.2 Vdc Out @ 36 Vdc In.62 Adc Input Stand-by Current Vin = 48 V, converter disabled 2.6 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 22 madc Input Reflected-Ripple Current 2MHz bandwidth 6 ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load) 1.188 1.2 1.212 Vdc Output Regulation Over Line ±1 ±3 mv Over Load ±1 ±3 mv Output Voltage Range Over line, load and temperature 2 1.182 1.218 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 9 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 12 mv Setting Time to 1% 1 µs EFFICIENCY 1% Load 82 % % Load 83 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 62 of 7

SQ48T/S112 (1.2 Volts Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.2V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T112 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.2V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T112 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.2V.3: Available load current vs. ambient temperature and airflow rates for SQ48S112 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.2V.4: Available load current vs. ambient temperature and airflow rates for SQ48S112 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 63 of 7

SQ48T/S112 (1.2 Volts Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16.6 2 4 6 8 1 12 14 16 Fig. 1.2V.: Efficiency vs. load current and input voltage for SQ48T/S112 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C. Fig. 1.2V.6: Efficiency vs. load current and ambient temperature for SQ48T/S112 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 6. 6... Power Dissipation [W] 4. 3. 2. 1. 72 V 48 V 36 V Power Dissipation [W] 4. 3. 2. 1. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 1.2V.7: Power dissipation vs. load current and input voltage for SQ48T/S112 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 1.2V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S112 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 64 of 7

SQ48T/S112 (1.2 Volts Out) Fig. 1.2V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (. V/div.). Time scale: 2 ms/div. Fig. 1.2V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (. V/div.). Time scale: 2 ms/div. Fig. 1.2V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 1.2V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 6 of 7

SQ48T/S112 (1.2 Volts Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 1.2V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 1.2V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 1.2V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.2V.14 for test setup. Time scale: 1 µs/div. Fig. 1.2V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.2V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 66 of 7

SQ48T/S112 (1.2 Volts Out) 1. 1. Vout [Vdc]. 1 1 2 Iout [Adc] Fig. 1.2V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.2V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 67 of 7

Electrical Specifications: SQ48T/S11 (1. Volt Out) Conditions: T A =2ºC, Airflow=3 LFM (1. m/s), Vin=48 Vdc, Vout=1. Vdc unless otherwise specified. PARAMETER NOTES MIN TYP MAX UNITS INPUT CHARACTERISTICS Maximum Input Current 1 Adc, 1. Vdc Out @ 36 Vdc In.2 Adc Input Stand-by Current Vin = 48 V, converter disabled 3 madc Input No Load Current ( load on the output) Vin = 48 V, converter enabled 22 madc Input Reflected-Ripple Current 2MHz bandwidth 7. ma PK-PK Input Voltage Ripple Rejection 12Hz TBD db OUTPUT CHARACTERISTICS Output Voltage Set Point (no load).99 1. 1.1 Vdc Output Regulation Over Line ±1 ±2 mv Over Load ±1 ±3 mv Output Voltage Range Over line, load and temperature 2.98 1.1 Vdc Output Ripple and Noise - 2MHz bandwidth Full load + 1 µf tantalum + 1 µf ceramic 3 mv PK-PK External Load Capacitance Plus full load (resistive) 1, µf Output Current Range 1 Adc Current Limit Inception Non-latching 16. 18 2 Adc Peak Short-Circuit Current Non-latching. Short=1mΩ. 3 4 A RMS Short-Circuit Current Non-latching.3 Arms DYNAMIC RESPONSE Load Change 2% of Iout Max, di/dt =.1 A/µS Co = 1 µf ceramic 8 mv di/dt = A/µS Co = 4 µf tant. + 1 µf ceramic 14 mv Setting Time to 1% 1 µs EFFICIENCY 1% Load 8. % % Load 81 % Additional Notes: 2. -4ºC to 8ºC SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 68 of 7

SQ48T/S11 (1. Volt Out) 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.V.1: Available load current vs. ambient air temperature and airflow rates for SQ48T11 converter with D height pins mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.V.2: Available load current vs. ambient air temperature and airflow rates for SQ48T11 converter with D height pins mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 2 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 1 1 LFM (2. m/s) 4 LFM (2. m/s) 3 LFM (1. m/s) 2 LFM (1. m/s) 1 LFM (. m/s) 3 LFM (.1 m/s) 2 3 4 6 7 8 9 Fig. 1.V.3: Available load current vs. ambient temperature and airflow rates for SQ48S11 converter mounted vertically with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. 2 3 4 6 7 8 9 Fig. 1.V.4: Available load current vs. ambient temperature and airflow rates for SQ48S11 converter mounted horizontally with Vin = 48 V, air flowing from pin 3 to pin 1 and maximum FET temperature 12 C. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 69 of 7

SQ48T/S11 (1. Volt Out).9.9.9.9.8.8 Efficiency.8 Efficiency.8.7.7 72 V 48 V 36 V.7.7 7 C C 4 C.6 2 4 6 8 1 12 14 16.6 2 4 6 8 1 12 14 16 Fig. 1.V.: Efficiency vs. load current and input voltage for SQ48T/S11 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C. Fig. 1.V.6: Efficiency vs. load current and ambient temperature for SQ48T/S11 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). 6. 6... Power Dissipation [W] 4. 3. 2. 1. 72 V 48 V 36 V Power Dissipation [W] 4. 3. 2. 1. 7 C C 4 C. 2 4 6 8 1 12 14 16 Fig. 1.V.7: Power dissipation vs. load current and input voltage for SQ48T/S11 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 3 LFM (1. m/s) and Ta = 2 C.. 2 4 6 8 1 12 14 16 Fig. 1.V.8: Power dissipation vs. load current and ambient temperature for SQ48T/S11 converter mounted vertically with Vin = 48 V and air flowing from pin 3 to pin 1 at a rate of 2 LFM (1. m/s). SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 7 of 7

SQ48T/S11 (1. Volt Out) Fig. 1.V.9: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (. V/div.). Time scale: 1 ms/div. Fig. 1.V.1: Turn-on transient at full rated load current (resistive) plus 1, µf at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal ( V/div.). Bottom trace: output voltage (. V/div.). Time scale: 1 ms/div. Fig. 1.V.11: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate:.1 A/µs. Co = 1 µf ceramic. Time scale:.2 ms/div. Fig. 1.V.12: Output voltage response to load current stepchange (3.7 A 7. A 3.7 A) at Vin = 48 V. Top trace: output voltage (1 mv/div.). Bottom trace: load current ( A/div.). Current slew rate: A/µs. Co = 4 µf tantalum + 1 µf ceramic. Time scale:.2 ms/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 71 of 7

SQ48T/S11 (1. Volt Out) i S i C 1 µh source inductance Vsource 33 µf ESR <1Ω electrolytic capacitor TM SemiQ Family DC/DC Converter 1 µf ceramic capacitor Vout Fig. 1.V.13: Output voltage ripple (2 mv/div.) at full rated load current into a resistive load with Co = 1 µf tantalum + 1uF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 1.V.14: Test Set-up for measuring input reflected ripple currents, i c and i s. Fig. 1.V.1: Input reflected ripple current, i c (1 ma/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.V.14 for test setup. Time scale: 1 µs/div. Fig. 1.V.16: Input reflected ripple current, i s (1 ma/div.), measured through 1 µh at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.V.14 for test setup. Time scale: 1µs/div. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 72 of 7

SQ48T/S11 (1. Volt Out) 1. 1. Vout [Vdc]. 1 1 2 Iout [Adc] Fig. 1.V.17: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.V.18: Load current (top trace, 2 A/div., 2 ms/div.) into a 1 mω short circuit during restart, at Vin = 48 V. Bottom trace (2 A/div., 1 ms/div.) is an expansion of the on-time portion of the top trace. SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 73 of 7

Physical Information 1 2 3 TOP VIEW SIDE VIEW SQ48S Pinout (Surface Mount) 8 7 6 4 SQ48S Platform Notes Pad/Pin Connections Pad/Pin # Function 1 Vin (+) 2 ON/OFF 3 Vin (-) 4 Vout (-) SENSE(-) 6 TRIM 7 SENSE(+) 8 Vout (+) All dimensions are in inches [mm] Connector Material: Copper Connector Finish: Gold over Nickel Converter Weight:.3 oz [1 g] Recommended Surface-Mount Pads: Min..8 X.112 [2.3 x 2.84] Max..92 X.124 [2.34 x 3.1] Height HT (Max. Height) CL (Min. Clearance) Option +. [+.] -.38 [-.97] +.16 [+.41] -. [-.] A.33 [7.69].3 [.77] B.336 [8.3].63 [1.6] C. [12.7].227 [.77] D.4 [1.16].127 [3.23] E.282 [7.16].9 [.23] 1 8 2 3 TOP VIEW 7 6 4 Pin Option PL Pin Length ±. [±.13] SIDE VIEW A.188 [4.77] B.14 [3.68] C.11 [2.79] SQ48T Platform Notes SQ48T Pinout (Through-hole) All dimensions are in inches [mm] Pins 1-3 and -7 are Ø.4 [1.2] with Ø.78 [1.98] shoulder Pins 4 and 8 are Ø.62 [1.7] without shoulder Pin material: Brass Pin Finish: Tin/Lead over Nickel Converter Weight:.3 oz [1 g] SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 74 of 7

Converter Part Numbering Scheme Product Series Input Voltage Mounting Scheme Rated Load Current Output Voltage ON/OFF Logic Maximum Height [HT] Pin Length [PL] SQ 48 T 1 18 - N B A Special Features One-Eighth Brick Format 36-7 V S Surface Mount T Throughhole 1 A (1. 3.3 V) 1 A (. V) 8 A (6. V).3 A (8. V) 4 A (12. V) 1 1. V 12 1.2 V 1 1. V 18 1.8 V 2 2. V 2 2. V 33 3.3 V. V 6 6. V 8 8. V 12 12. V N Negative P Positive SMT S.273 Through hole A.33 B.336 C. D.4 E.282 SMT. Through hole A.188 B.14 C.11 STD T Alternative Trim Option (For 1.2V & 1.V only) The example above describes P/N SQ48T118-NBA: 36-7 V input, through-hole mounting, 1 A @ 1.8 V output, negative ON/OFF logic, a maximum height of.336, and a through the board pin length of.188. Please consult factory regarding availability of a specific version. Fig. H: Location of the thermocouple for thermal testing. For more information please contact di/dt, Inc. 1822 Aston Avenue Carlsbad, CA 928 USA USA Toll Free 866-WOW-didt (969-3438) www.didt.com support@didt.com The information and specifications contained in this data sheet are believed to be accurate and reliable at the time of publication. However, di/dt, Inc. assumes no responsibility for its use or for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of di/dt, Inc. Specifications are subject to change without notice. Copyright di/dt, Inc. 23 SQ48 Family DS Ver 2 3-2-3 USA Toll Free 866 WOW-didt Page 7 of 7