QUICK FLOW CDT1 series Digital Flowmeter for ir Conditioning pplication OUTLINE CDT1 is a new series of flowmeter which combines a multidigital indicator with a pitot tube. CDT1 detects the differential pressure exerted by flow velocity in the pitot tube inserted in the pipe and s flow rate with digital indication. pplicable sizes range from 2mm to 4mm dia. The principal applications are for hot and cooling water lines for air conditioning in apartment and office buildings and other facilities. FETURES Easy installation Installation simply by making a 5mm dia. hole and welding 2mm (/4") socket at measuring point of existing pipes. This is most convenient for renewal use when additional flow sensor is required on the line. Low pressure drop Wide measuring range Measuring range selectable depending on application pplicable for both horizontal and vertical pipes. Various indicator functions selectable from the following: Battery type, Current Output type (2wire 4 to 2m), larm Output type, Temperature Sensor Input type and LonWorks type Indicator parts are interchangeable. Easy to see because of large LCD display Compact size and lightweight Quick delivery STNDRD SPECIFICTION Measuring Fluid : Water, Cold water, Hot water Max. Pressure : 2MPa Max. llowable Differential Pressure : 2kPa (Bias pressure) Temperature and Relative Humidity Fluid temperature : 1 to 7 o C mbient Temp. : 1 to o C < 85%RH Storage Temp. : 2 to 6 o C < 85%RH (Without icing, without condensation) Process pipe size : 2mm(/4") to 4mm(18") daptation pipe : Carbon steel pipe for piping (JIS G 452) [1MPa class] Carbon steel pipe for pressure piping (JIS G 454 Sch4) [2MPa class] Note : If pipe other than above is required, special calibration may be necessary. Consult factory for details. ccuracy : 5% F.S. [std.] ccuracy is guaranteed for fluid temperature range 7 to 6 o C Measuring range : Flow rate from 1 to 1% of full scale Protection class : IP65 (JIS C 92) (Except for the air introduction port at the bottom of housing.) Mass : pprox. 2kg Indicator type function (ll types with indicator) Type Battery type Current type larm type larm B type Temp. sensor input type LonWorks Type Function Battery drive, Indication only 42m DC (2wire) 2 points 42m DC 2 points Temp. Indication Temp. Indication, Battery drive pplicable to LON communication network Indication function Flow rate indication 1/2 digits LCD (Height 18mm) : to 1999 (FFF appears in case of out of range) 11 segment bar graph Totalizer indication 71/2 digits LCD (Height 5mm): to 19999999 Indication interval : 1s (Sampling.5 sec) Filter :,2,4,8,16,2s (Moving average) LCD back light : Continue 1s after operation (Except current type) Material of Pitot tube parts : Refer to [OUTLINE DIMENSION] and [MTERIL] Material of wetted parts of indicator Diaphragm : 16L SS Body : 16SS : Fluorine rubber (JIS Class4D) Drain hole sealing : lumina ceramics Material of indicator body: luminium alloy Painting : Melamine resin painting (Indicator housing) Painting color Front : Wine red (Munsell 1RP/8) Rear : Light gray (Munsell N7.5) Process connection : R/4" (M) Installation posture : Front vertical installation TGF9761E May. 2
CDT1 QUICK FLOW for ir Conditioning pplication Digital Flowmeter Standard full scale range [SGP,STPG(4~4mm)pipe] Process pipe size Full scale range [L/min] Inside dia. (mm) mm inch Code 5 1 2 1MPa 2MPa 2 /4 7 1 (26) Refer to 25 1 7 1 1 (4) following 2 11/4 12 16 2 (4) table 4 11/2 1 2 41.6 41.2 2 2 4 52.9 52.7 65 21/2 4 7 67.9 65.9 8 7 1 8.7 78.1 1 4 9 1 18 15. 12. 125 5 1 2 28 1.8 126.6 1 6 2 4 155.2 151. 2 8 7 24.7 199.9 2 1 7 1 254.2 248.8 12 8 1 16 4.7 297.9 14 1 1 2 9.8.4 4 16 1 18 2 9.6 81. 4 18 16 2 441.4 428.6 Standard full scale range [2MPa version = 2~2mm] Process pipe size Full scale range [L/min] Inside dia. mm inch Code 1 2 (mm) 2 /4 7 1 21.4 25 1 7 1 1 27.2 2 11/4 12 16 2 5.5 Standard full scale range [PVC lined pipe] Process pipe size Full scale range [L/min] Inside dia. mm inch Code (mm) 5 1 2 2 11/4 75 1 1 29.5 4 11/2 1 1 2 4.7 2 17 2 46.2 65 21/2 4 6 59.7 8 4 6 9 7.9 1 4 8 1 16 95.2 125 5 12 18 2 119.7 1 6 17 2 142 Note 1) The inside diameter of pipe size 2 to 2mm in 1MPa is based on threeway socket (JIS B 21). (It is possible to attach threeway socket as option.) 2) The inside diameter of pipe size 2 to 2mm in 2MPa is based on threeway socket (Sch.4). (Supplied by customer.) ) 4mm or more, the inside diameter of in 1MPa specification is based on Carbon steel tube for ordinary piping SGP (JIS G452), and the inside diameter of in 2MPa specification is based on Carbon steel pipes for pressure piping STPG (JIS G 454 Sch4). 4) Scale range of PVC lining is based on the inside diameter of the upper table. In the case of inside diameter other than the upper table, special calibration is required. Consult after checking L and D size of the figure in page 6. Specification and function of each type 1) Battery type Battery :lkali battery (LR6) x 2 pcs. Battery life :pprox. 2 years at 2 o C uto power off mode selectable Low Battery monitor as standard 2) Current type Power supply :24V DC 1% Output :42m DC (2wire) Max. load :6Ω Output accuracy :.5% F.S. at 2 o C Response :Less than 2 s (t filter setting ) ) larm type Power Supply :24V DC 1% Power Consumption :Less than 25m larm Output :Open Collector x 2 (Independent) Load :Less than V DC / 8m Response :Less than 2 s (t Filter setting ) larm setting :Selectable (high / Low), Reset Span: djustable / Min. 1digit Output : 42m DC Max. load :6Ω Output ccuracy :.5%F.S.at 2 o C 4) larm B type Power Supply :24V DC 1% Power Consumption :Less than 25m larm Output :Open Collector x 2 (Independent) Load :Less than V DC / 8m Response :Less than 2 s (t Filter setting ) larm setting :Selectable (high / Low), Reset Span: djustable / Min. 1digit Connecting Temp. Sensor:Pt1Ω (wire) (JIS C 164) Temp. Indication :1 to 8 o C Indication Interval :6 s Temp. Ind. ccuracy : 2 o C (Excluding sensor error) 5) Temperature sensor input type Following function is added to battery type Connecting temp. sensor :Pt1Ω (wire) (JIS C 164) Temp. Indication :1 to 8 o C Indication interval :6 s Temp. indication accuracy: 2 o C (Excluding sensor error) 6) LonWorks type pplicable to Lon communication network. Communication with network devices by FTT1 Transceiver. Power Supply :24V C 1% /, 6Hz Power Consumption :Less than 8m Transmission LON Value :Flowrate and differential pressure (Convert the Indication value to LON value) Response :Less than 2 s (t Filter setting ) The communication of each device is in accordance with definite procedure related to its LON value. FTT1 can be connected by free topology and multi drop connection. Refer to [Function Profile] for detailed information Cable entry Type Cable entry L Cable entry R Battery type Current type larm type larm B type Temperature sensor input type LonWorks type cceptable cable outside diameter 8mm OPTION (Factory set) Totalizing indication Selection of totalizer function CODE : /TLZ Selection of Temp. indication unit : o F (Export Model) Temp. sensor input type only (Standard unit : o C) CODE : /TPF OPTION (Others) Refer to L CODE : Yes : No 2 TOKYO KEISO CO., LTD. TGF9761E
l CDT1 QUICK FLOW for ir Conditioning Digital Flowmeter WIRING DIGRM [Current type] [larm type] larm (1)/(2) : Open collector Load: Less than V DC/8m (each) [larm B type] [Temp. sensor input type] [LonWorks Type] larm (1)/(2) : Open collector Load: Less than V DC/8m (each) 42m DC24V Receiver N OUT DC24V larm (1) larm (2) 42m Receiver b larm (1) DC24V larm (2) b B Pt1Ω Black Red White blue ~ C24V NETB NET Host device B Pt1Ω MTERIL and OUTLINE DIMENSION CDT12 9 (.5) (184) (84) (1) l 1 2 4 5 6 72 1 o ff O U T 1 O U T 2 L R Z.kPa UNI T m / h c m / h o C (95) 16 1.5 (9) (9) R/4 (Refer to approval drawing for the dimension I.) (21) Drain hole Cable entry L 21 CDT14 9 24 Cable entry R 5 (91.5) (84) 1 (14) Socket (CFSW) 9 /4 4.5 [OPTION] 8 SGP threeway socket (JIS B 21/CFTW) Rc/4 1 O U T 1 O U T 2 UNI T m / h ir vent screw B 2d c m / h of f L R Z.kPa o C 72 Dimension of threeway socket Size d B 2mm Rc/4 25mm Rc1 5 6 2mm Rc11/4 6 41 (199) 2 No. Part Description Material (41) (47) (127) (66.5) 4 Indicator body luminum alloy Isolation valve SCS 14 Valve Shaft SUS 16 NBR 5 Vent valve SUS 16 Cap nut SCS1 R/4 6 Fittings BC6 Pitot tube SUS 16 Socket SS 4*1 8 Threeway socket FCMB*1,2 *1 It is possible to attach standard material for socket (SS4 or FCMB) if requested, but material besides these materials shall be provided by customer when needed. *1,2 In the 2MPa specification, material is equivalent to S25C. Supplied by customer. (Note: Sch4 specification) TGF9761E TOKYO KEISO CO., LTD.
1 1 1 o cm/h o C o CDT1 QUICK FLOW for ir Conditioning pplication Digital Flowmeter CONSTURUCTION CDT1 2 Vent valve (4pcs) Equalizing pressure valve with (P4) Bolt, Washer M5 x 2(4pcs) (S4) Vent plug (4pcs) (P8) (P8) Cap nut (S1.5) Pitot tube SCS14 Isolation valve Socket Fittings Screwing Welding Blind plug Piping Indicator off LRZ kpa UNIT m/h cm/h Hexagon socket head cap screws M4 x 14(4pcs) C CDT1 4 Hexagon socket head cap screws M4 x 14(4pcs) Indicator off LRZ kpa UNIT m/h cm/h [Option] Protection cover (For indicator protection) CODE : /HGC CUTIONS ON INSTLLTION void direct rays and equip with a protection cover or install in the place which a direct rainstorm does not splash. (If protection cover is used, it may be difficult to read the display.) Protection cover Equalizing pressure valve with (P4) (S4) Isolation valve Screwing Fittings Socket Blind plug Vent valve (2pcs) Vent plug (2pcs) Bolt, Washer M5 x 2(4pcs) (P8) (P8) Pitot tube (S1.5) Cap nut Welding off UNIT m/h C Piping 4 TOKYO KEISO CO., LTD. TGF9761E
CDT1 QUICK FLOW for ir Conditioning Digital Flowmeter L CODE CDT1 L / Description Installation 2 Horizontal type type 4 Perpendicular type 1 1MPa class Pressure rating 2 2MPa class 2 2mm 25 25mm 2 2mm 4 4mm mm 65 65mm 8 8mm 1 1mm Main pipe size 125 125mm 1 1mm 2 2mm 2 2mm mm mm 4 4mm 4 4mm 5 1 Full scale range Flow rate range 2 4 Battery type 5 Current type 6 larm type Indicator type 7 larm B type 8 Temp.sensor input type 9 LonWorks type pplication L For liquid Version Version code /TLZ Totalization indicator /TPF Indication Temp. o F Option* /CFS Welding sockt (CFSW) /PL PVC lined pipe specification Blank Not provided dditional function /Z Provided /HGC With protection cover at display part /CFT Threeway socket for piping (CFTW) *Note) Insert / between each code when the plural codes are selected. Note Standard type Vertical type Carbon steel pipe for piping (JIS G 452) Carbon steel pipe for pressure piping (JIS G 454 Sch4) Nominal diameter for installation pipe Select for the code of Standard full scale range Battery drive 42m DC (2wire) 2 points 42m DC 2 points Temp. input. Indication Temp. input. Indication, Battery drive LonWorks available Indication type and incase of export are available ttachment is possible in case of the quality of the material FCMB and 1MPa specification vailable only for SS4 Inform us L and D dimension of figure in page 6. Not necessary if abovementioned code is available. Consult about the details of the pipe material or Pitottube length. Code example 1: [In case optional code is not selected] Horizontal installation, Connection size mm, 1MPa class, Full scale flow rate code[1], Battery drive type Model code: CDT12114L Code example 2: [In case all of the possible optional codes are selected] Vertical installation, Connection size 1mm, 1MPa class, Full scale flow rate code[5], Temp. sensor input type, Totalization indicator, indication, With protection cover at display part, With welding socket Model code: CDT141158L/TLZ/TPF/HGC/CFS Code example : [In case piping type specification] Horizontal installation, Connection size 8mm, Pipe material SUS4TPD, 1MPa class, Full scale flow rate code[2], Current type, Totalization indicator, With welding socket Model code: CDT121825L/TLZ/CFS/Z When the piping type is specified as seen in the above Code example, it will be additional function. Moreover, in case socket and threeway socket are prepared by customer, Pitot tube length may be changed by installation dimension. This will be an additional function. ccordingly the last letter of model code will be /Z in case of such special specification as not mentioned in the above mode code. TGF9761E TOKYO KEISO CO., LTD. 5
CDT1 QUICK FLOW for ir Conditioning pplication Digtal Flowmeter INSTLLTION 1) Select the installation place in consideration of the required straight length. 2) Make the hole of ø5 in place of the pipe for more than 4mm. 2mm process piping : Install threeway socket. ) Select the position of the hole prudently so as the indicator would become vertical after the fixing has been made. 4) Weld the socket to the drilled hole. t this time the center line of the socket and the center line of the piping shall be crossed. 5) It is over completed when CDT1 is installed in the socket welded. Piping CDT22 CDT24 Threeway socket (2 to 2mm) Threeway socket Rc/4 Rc/4 Threeway socket SUGGESTIONS CDT12(4)1 flowmeter is calibrated for use with standard steel pipe lines. In case the pipe material is different from standard steel pipe, special calibration is required. Consult factory for details. Straight length for upstream and downstream is required for accurate measurement as shown in the following table, Size Upstream Downstream 2 1D 5D 4 5D D Note) D : Inside diameter of main pipe. Use this flowmeter, filling with water in the pipe. In case the fluid is liquid,eliminate the air in according to the CDT1 Instruction manual. LINING ND OTHER PIPING In case of PVC lining piping, prepare bushing (25mm x 2mm) for the main pipe in more than 2mm and for branch tube in 25mm. vailable for other piping. Inform of the types of piping and dimension of L and D of the following figure. Refer to the table for full scale flow rate. Straight piping ( 4mm) /4 /4 9 ØD 2mm L Bushing (R1 x Rc/4) ØD L Rc/4 Ø5 Ø5 Lining piping (PVC) Other piping 9 ORDERING INFORMTION Indicator 1. Model code 2. Quantity * Specification subject to change without notice Head Office : Shiba Toho Building, 1 7 24 Shibakoen, Minatoku, Tokyo 15 8558 Tel : 41 1625 (KEY) ; Fax : 4 4922 email : overseas.sales@tokyokeiso.co.jp ; URL : http://www.tokyokeiso.co.jp 6 TGF9761E