116 E5 Cam Latches Overview Modularity and simplicity in action The SOUTHCO E5 cam latch is a highly modular and easy to configure solution, suitable for a wide range of applications. By changing any of the three basic components (access style driver, latch body or cam in either geometry or material, the E5 can be easily adjusted to suit most applications. Product features ÂÂ Cost effective, easy to design and install ÂÂ Multiple material and access options to suit multiple needs ÂÂ Suitable to meet NEMA 4 / IP65 sealing standards ÂÂ Corrosion-resistant materials available ÂÂ Highly modular and configurable Match material and finish options for style and functionality requirements A variety of materials and finishes to complement your application. Die-cast zinc latch bodies standard finishes: Chrome plated Black powder coated Corrosion resistant materials available 316 Stainless steel Glass-filled nylon, black 304 Stainless steel Select one of these four styles to fit your access requirements There are four basic E5 styles to meet specific door configuration and mounting requirements in terms of design, depth, surface protrusion and operation style. 27.2 (1.07 23.7 (0.93 36 (1.42 46 (1.81 A E5 Standard Industry standard, highly modular and configurable options in a wide choice of materials, finishes and access styles. (See page 118 E5 Low Profile Stylish, low profile design. Tool and hand operated access styles in zinc alloy chrome plated or black powder coated. (See page 120 E5 Push-to-Close Standard E5 with the added functionality of a springloaded cam or actuator for single or multi-point operation. Provides quicker turn-to-open, push-to-close action. (See page 128 E5 Flush Cup Wing Knob Stylish oval cup design. Provides a clean, flush outer surface. Ideal for multi-point actuation of large doors in aesthetically pleasing applications. (See page 122 www.southco.com
117 Choose from a wide range of operating styles to fit application and industry requirements. 6 21 y Ke s c ni re tro llco c Ele (Be ÂÂ Convenient hand-operated wing knob, T and L-handle styles for easy hand access ÂÂ Tool operated for restricted access, flush-mount or low-profile clearances, and industry-specifc standards ÂÂ Key operated for added security Tool / key operable 9 (.35 Slotted Recessed slot Railway standard Hex recess 216 electronics ng wi Sh ort recess.19 bit 5 ( ble u Do.11 bit 3 ( ble u Do.19 bit 5 ( ble u Do ss.32 ce 8 ( re re ua Sq ng wi ll Ta.28 le 7 ( iang Tr Cylinder lock.11 bit 3 ( ble u Do Sh 5 (.19 6 (.24.28 e 7 ( quar S.28 le 7 ( iang Tr Flush wing Tall wing 3 (.11 ss.32 ce 8 ( re re ua Sq Short wing o Wing knob non-locking.32 e 8 ( quar S L-handle non-locking.32 le 8 ( iang Tr L-handle key-locking Wing knob locking.32 ess 8 ( rec x.32 le He 8 ( iang Tr T-handle non-locking.28 e 7 ( quar S.32 e 8 ( quar S T-handle key-locking r inlglco tr wbe e2 16 l Be re lco y Ke nigcs i ll wron ore Tlaect ellc E (B Hand operable Total grip includes the dimensions of all elements in-between the mounting surface of the latch and the latch's contact surface on the frame - including door thickness, compressed seals and gaskets, accessories, frame offset, etc. Some SOUTHCO E5 latches are shipped latch and cam separately and some completely pre-assembled. See product pages for details. Slo 7 (.0 7 2 (.0 d tte Slo 15 58 (. 2 15 58 (..32 ess 8 ( rec x He Installation d tte Determine your grip options for a perfect fit Cam Screw Sealing washer Mounting nut Selecting the right cam for the E5 is easy once the total grip is known. Southco provides a wide selection of standard cams in many grip increments, and special ones like hook and push-to-close cams. Standard cams provide vibration resistance and grip variation tolerance. E5 Standard E5 Low Profile Latch and cam shipped separately. Latch and cam shipped pre-assembled.
118 E5 Cam Latch Stainless steel Tool operated Fixed grip Single hole install Latched / unlatched indicator EN 45545-3 E60 Compliant Stainless steel, 304 or 316 grade Maximum static load: 304 Stainless steel 550 N (124 lbf 316 Stainless steel 670 N (150 lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Installation Mounting nut: Maximum tightening torque: 20 N m (177 in lbf Screw Maximum tightening torque 10 N m (90 in lbf Keys and Accessories +0.1 20.1-0 +.004 (.79 -.000 H Head Styles Slotted Hex recess 6 (.24 Max. 1 (.04 Min. Ø 28 (1.10 36±4 (1.42±.15 +0.5 +.02 Ø 22.5 (.89-0 -.00 8 (.31 5 (.20 0.5 (.02 Sealing washer (compressed 19 (.75 28 (1.10 Mounting nut 4 (.16 Internal O-ring Internal spring 3 (.11 Cam 45 (1.77 5 (.19 23 (.91 Optional Detent Version Detent housing prevents accidental cam movement. Cam securely detents in place both in open and closed positions. 216 Railway standard Selection Order latch and cam separately Latch (no cam E5 - B - H M - UU1 H Head style 00 Slotted 01 Hex recess 02 03 04 05 06 3 (.11 07 5 (.19 13 216 22 Railway standard B Body 6 Normal housing 32 Detented housing M Material 24 304 Stainless steel 27 316 Stainless steel +2(.08-0 (.00 304 Stainless steel 316 Stainless steel +2(.08-0 (.00 Cam Table (order separately from latch 304 316 304 +2(.08 Stainless Stainless Stainless - 0 (.00 steel steel steel 316 Stainless steel +2(.08-0 (.00 304 Stainless steel 316 Stainless steel 4 (.16 E5-8003 E5-9003 14 (.55 E5-8008 E5-9008 24 (.94 E5-8013 E5-9013 34 (1.34 E5-8018 E5-9018 6 (.24 E5-8004 E5-9004 16 (.63 E5-8009 E5-9009 26 (1.02 E5-8014 E5-9014 36 (1.42 E5-8019 E5-9019 8 (.31 E5-8005 E5-9005 18 (.71 E5-8010 E5-9010 28 (1.10 E5-8015 E5-9015 38 (1.50 E5-8020 E5-9020 10 (.39 E5-8006 E5-9006 20 (.79 E5-8011 E5-9011 30 (1.18 E5-8016 E5-9016 40 (1.57 E5-8021 E5-9021 12 (.47 E5-8007 E5-9007 22 (.87 E5-8012 E5-9012 32 (1.25 E5-8017 E5-9017 42 (1.65 E5-8022 E5-9022
E5 Cam Latch Zinc Tool operated Adjustable grip 118A Ø 28 (1.10 Ø 28 (1.10 +0.1 20.1-0 +.004 (.79 -.000 6 (.24 Max. 1 (.04 Min. H Head Styles Slotted Hex recess 45 (1.77 45 (1.77 36±4 (1.42±.15 +0.5 +.02 Ø 22.5 (.89-0 20 (.79 20 (.79 -.00 19 (.75 19 (.75 5 (.20 53 (2.09 18 (.71 Lock washer (2x 0.5 (.02 Sealing washer (compressed Mounting nut 4 (.16 M10 Jam nut (2x Do not adjust screw 3 (.11 Shaft adapter Internal O-ring Internal spring 5 (.19 recess 8 (.31 Extended 216 Single hole install Latched / unlatched indicator Easy grip adjustment Tool operated for security Zinc alloy, powder coated or chrome plated and steel, zinc plated Maximum static load: 330 N (74 lbf Installation Position cam so latching function can be achieved comfortably by hand. Recommended tightening torque for mounting nut is 10 N m (88 in lbf max, and jam nut is 7 N m (62 in lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Keys and Accessories electronics Recessed slot (tamper resistant F Finish 2 Bright chrome 5 Black powder coated Railway standard Selection Latch (no cam Order latch and cam separately E5-6 - H F - 01 H Head style 00 Slotted 01 Hex recess 02 03 04 05 06 3 (.11 Cam Table (order separately from latch Minimum +2(.08-0 (.00 Maximum +2(.08-0 (.00 Cam Type 5 (.20 16.5 (.65 Deep Offset Cam, Forward 51 (2.01 62.5 (2.46 Deep Offset Cam, Reversed 16.5 (.65 28 (1.10 Offset Cam, Forward 39.5 (1.56 51 (2.01 Offset Cam, Reversed 07 5 (.19 08 recess 13 216 19 electronics 21 Recessed slot (tamper resistant 22 Railway standard E5-4001 E5-4002 28 (1.10 39.5 (1.56 Straight Cam E5-4003
E5 Cam Latch Zinc Tool operated Fixed grip 119 +0.1 20.1-0 +.004 (.79 -.000 H Head Styles Slotted Hex recess electronics 6 (.24 Max. 1 (.04 Min. F Finish 2 Bright chrome 5 Black powder coated +2(.08-0 (.00 Recessed slot (tamper resistant Ø 28 (1.10 36±4 (1.42±.15 +0.5 +.02 Ø 22.5 (.89-0 -.00 19 (.75 5 (.20 0.5 (.02 Sealing washer (compressed E5-6 - H F - UU1 Railway standard 27.2 (1.07 Mounting nut 4 (.16 Internal O-ring Internal spring 3 (.11 H Head style 00 Slotted 01 Hex recess 02 03 04 05 06 3 (.11 Cam Table (order separately from latch +2(.08-0 (.00 +2(.08-0 (.00 Cam 45 (1.77 5 (.19 23 (.91 recess 216 07 5 (.19 08 recess 13 216 19 electronics 21 Recessed slot (tamper resistant 22 Railway standard +2(.08-0 (.00 4 (.16 E5-6003 14 (.55 E5-6008 24 (.94 E5-6013 34 (1.34 E5-6018 6 (.24 E5-6004 16 (.63 E5-6009 26 (1.02 E5-6014 36 (1.42 E5-6019 8 (.31 E5-6005 18 (.71 E5-6010 28 (1.10 E5-6015 38 (1.50 E5-6020 10 (.39 E5-6006 20 (.79 E5-6011 30 (1.18 E5-6016 40 (1.57 E5-6021 12 (.47 E5-6007 22 (.87 E5-6012 32 (1.25 E5-6017 42 (1.65 E5-6022 Single hole install Latched / unlatched indicator EN 45545-3 E10 Compliant Zinc alloy, powder coated or chrome plated and steel, zinc plated Maximum static load: 330 N (74 lbf Installation Mounting nut: Maximum tightening torque: 10 N m (88 in lbf Screw Maximum tightening torque: 5 N m (45 in lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Keys and Accessories Suitable for push-to-close action see page 128 Selection Latch (no cam Order latch and cam separately
119A E5 Cam Latch Zinc Shutter Tool operated Fixed grip Single hole install Latched / unlatched detent Vibration resistant EN 61373 Compliant Zinc alloy, powder coated or chrome plated and steel, zinc plated Maximum static load: 330 N (74 lbf Installation Mounting nut maximum tightening torque: 10 N m (88 in lbf Screw Maximum tightening torque: 5 N m (45 in lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Keys and Accessories +0.1 20.1-0 +.004 (.79 -.000 H Head Styles Ø28 (1.10 6 (.24 Max. 1 (.04 Min. 19 (.75 36±4 (1.42±.15 +0.5 +.02 Ø 22.5 (.89-0 -.00 5 (.20 27.2 (1.07 0.5 (.02 Sealing washer (compressed 4 (.16 Mounting nut Cam 23 (.91 45 (1.77 Insert key to depress shutter and rotate cam 216 Selection Order latch and cam separately Latch (no cam E5-8 - H F - UU1 H Head style 02 03 04 05 F Finish 13 216 2 Bright chrome 5 Black powder coated Cam Table (order separately from latch 4 (.16 E5-6003 14 (.55 E5-6008 24 (.94 E5-6013 34 (1.34 E5-6018 6 (.24 E5-6004 16 (.63 E5-6009 26 (1.02 E5-6014 36 (1.42 E5-6019 8 (.31 E5-6005 18 (.71 E5-6010 28 (1.10 E5-6015 38 (1.50 E5-6020 10 (.39 E5-6006 20 (.79 E5-6011 30 (1.18 E5-6016 40 (1.57 E5-6021 12 (.47 E5-6007 22 (.87 E5-6012 32 (1.25 E5-6017 42 (1.65 E5-6022
120 E5 Cam Latch Low Profile Zinc Tool or hand operated Fixed grip Single hole install Latched / unlatched indicator Shipped fully assembled EN 45545-3 E10 Compliant Zinc alloy, powder coated or chrome plated and steel, zinc plated Maximum static load: 330 N (74 lbf Installation Mounting nut Maximum tightening torque: 10 N m (88 in lbf Keys and Accessories Latch is shipped fully assembled For door thicknesses 1-6 (.039 -.236 grip must exceed door thickness by 4 (.157 for assembled installation When sealing option is selected, add 0.4 (.02 to grip calculation to accommodate sealing washer Ø 31 (1.22 +0.1 20.1 0 +.004 (.79 -.000 H Head style 00 Slotted 01 Hex recess 02 03 04 05 06 3 (.11 7.5 (.30 for 216 Drive stud 4.5 (.18 for all other head styles except wing versions 45 D (1.77 thickness G 14 (.55 Max 1 (.04 Min Housing Mounting nut M 22 X 1.5 thread Detent washer Cam 23.7 (.93 For short housing 31.7 (1.25 For long housing 36±4 (1.42±.15 Ø 22.5 +.5 +.02 -.0 (.89 -.00 07 5 (.19 08 recess 11 Short wing 12 Tall wing 13 216 19 Electronics E5 - D - H F - G S H Head Styles Slotted Hex recess recess 216 14.5 (.57 Short wing electronics 3 (.11 19.5 (.77 F Finish 1 Textured chrome 5 Black powder coated 5 (.19 Selection Tall wing S Sealing option 0 No o-ring or external seal 1 O-ring and external seal to meet NEMA 4/IP65 standards D thickness range 1 1-6 (.039 -.236 (short housing supplied 2 1-14 (.039 - (.551 (long housing supplied G table G Short housing Long housing G Short housing Long housing G Short housing Long housing G Short housing Long housing 00 Do not use 6 (.24 05 8 (.31 16 (.63 10 18 (.71 26 (1.02 15 28 (1.10 36 (1.42 01 Do not use 8 (.31 06 10 (.39 18 (.71 11 20 (.79 28 (1.10 16 30 (1.18 38 (1.50 02 2 (.08 10 (.39 07 12 (.47 20 (.79 12 22 (.87 30 (1.18 17 32 (1.25 40 (1.57 03 4 (.16 12 (.47 08 14 (.55 22 (.87 13 24 (.94 32 (1.25 18 34 (1.34 42 (1.65 04 6 (.24 14 (.55 09 16 (.63 24 (.94 14 26 (1.02 34 (1.34 19 36 (1.42 44 (1.73 If grip falls between two choices, use the smaller option
E5 Cam Latch Glass-filled nylon Tool or hand operated Fixed grip 121 Ø ( ( Ø ( ( Single hole install Corrosion-resistant materials 6 (.24 0.5 (.02 Sealing washer (Compressed ( Ø ( ( 0.5 (.02 Sealing washer (Compressed Glass-filled nylon and Stainless steel Average ultimate load: 300 N (68 lbf L Mounting nut G L Mounting nut G Installation Mounting nut Maximum tightening torque: 4.25 N m (38 in lbf +0.1 20.1-0 +.004 (.79 -.000 ( 26±4 (1.02±.16 ( ( ( Sealing NEMA 4 / IP65 achieved using gasket supplied Keys and Accessories H Head Styles +0.5 +.02 Ø 22.5 (.89-0 -.00 6 (.24 Max. 1 (.04 Min. E5-4 - H 3 - G 1 Slotted 3 (.11 Wing knob Latch H Head style 00 Slotted 03 05 06 3 (.11 30 Wing knob Selection Total G L Max. Thickness for Assembled Latch Total G L G table Max. Thickness for Assembled Latch Total G L Max. Thickness for Assembled Latch 16 (.63 16 28.1 (1.1 5 (.20 24 (.94 24 34.6 (1.36 6 (.24 30 (1.18 30 40.6 (1.6 6 (.24 18 (.71 18 28.1 (1.1 5 (.20 25 (.98 25 35.6 (1.4 6 (.24 32 (1.26 32 42.6 (1.68 6 (.24 20 (.79 20 28.1 (1.1 6 (.24 26 (1.02 26 36.6 (1.44 6 (.24 34 (1.34 34 44.6 (1.76 6 (.24 22 (.87 22 32 (1.26 6 (.24 28 (1.10 28 38.6 (1.52 6 (.24 36 (1.42 36 46.6 (1.83 6 (.24
122 E5 Cam Latch Zinc Flush cup wing style Hand operated Fixed grip Low profile Multiple key code options Zinc alloy, powder coated and steel, zinc plated Maximum static load: 330 N (74 lbf Installation Mounting nuts 10-24 UNC (supplied maximum tightening torque: 3 N m (25 in lbf Screw maximum tightening torque: 10 N m (90 in lbf Keys Two point push-to-close action: Internal spring causes return of wing knob and actuator to original latched position when wing knob is released after opening. Ideal for use with cables and rotary latches. For lock core selection and a complete overview of the SOUTHCO Key-Choice System see page 158 Single Point Two Point (for use with rods Two Point Push-to-Close Action (spring-loaded 96 (3.8 Maximum door thickness Mounting nut 3.2 (.125 2.4 (.094 46 4 (1.8 (.16 2 Holes Ø 5.5± 0.1 (.22±.004 76 (3.0 Type A (reverse frame for type B Type A 23 (.91 60 (2.36 19 (.75 Single point cam 9.2 (0.36 51±4 (2.00±.16 Single point only 46 (1.8 31 (1.22 Rod clearance Actuator (supplied 4.4 (.18 36 (1.42 6.5 (.26 Actuator (supplied Rods (contact Southco for options Ø 6.1 (.24 20 (.80 55 (2.18 18 (.7 51 (2.0 Cables 3.5 (.14 Two point actuator (order separately, see page 131 15.2 (.59 Ø 65.5±0.5 (2.58±.02 40±0.2 (1.57±.008 80±0.3 (3.14±.01
123 R Rotation Type A Turn clockwise to latch Type B Turn counter-clockwise to latch L Lock Styles Non-locking key code CH751 key code R001 (order lock core separately Latch (no cam E5-9 R - L 5 - A S - 1 K R Rotation 1 Type A clockwise to latch 2 Type B counterclockwise to latch S Sealing option 0 Non-sealing (when A = TR or TL 1 Sealed (when A = UU or RR K Key options 0 No keys supplied (order separately, see page 130 3 1 Overmolded key supplied A Assembly status UU Single point order cam separately RR Two point (for use with rods - actuator supplied TR Type A two point push-to-close (order actuator separately TL Type B two point push-to-close (order actuator separately Selection Single point Order latch and cam separately Two point (for use with rods Order latch only (two point actuator supplied Two point push-to-close action (spring loaded Order latch and actuator separately. Actuator part number A5-91-201-11, see page 131 for details. To be used with SOUTHCO R4 rotary series latches and cables see page 272. L Lock Style 30 Non-locking (omit last 2 digits from part number 31 black lock core keyed alike CH751 32 stainless steel scalp and shuttered lock core keyed alike R001 33 Without lock core (omit last 2 digits from part number Order lock core separately, see page 158 Cam Table (order separately from latch 22.7 (.89 E5-6603 30.7 (1.21 E5-6607 24.7 (.97 E5-6604 32.7 (1.29 E5-6608 26.7 (1.05 E5-6605 34.7 (1.37 E5-6609 28.7 (1.13 E5-6606 36.7 (1.44 E5-6610 If grip falls between two choices, use the smaller option
124 E5 Cam Latch Zinc L-handle Hand operated Fixed grip Single hole install Multiple key codes Zinc alloy, powder coated or chrome plated and steel, zinc plated Maximum static load: 330 N (74 lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Installation Mounting nut: Maximum tightening torque: 10 N m (88 in lbf Screw maximum tightening torque: 10 N m (90 in lbf Keys Suitable for push-to-close action see page 128 For lock core selection and a complete overview of the SOUTHCO Key-Choice System see page 158 For adjustable grip versions see page 134 Selection Order latch and cam separately Ø 28 Ø 25 (1.10 (.98 L Lock Style Non-locking Latch (no cam 112.5 (4.42 Key code CH751 Key code R001 E5-9 - L F - UU1-1 K L Lock style 70 Non-locking (omit last two digits of part number 71 Keyed CH751 (lock core finish matches handle finish 72 Keyed R001 (stainless steel scalp shuttered 73 Without lock core (omit last two digits of part number Order lock core separately, see page 158 0.5 (.02 Sealing washer (compressed 17.9 (.7 27 (1.06 4 (.16 +0.1 20.1-0 +.004 (.79 -.000 6 (.24 Max. 1 (.04 Min. F Finish 2 Bright chrome 5 Black powder coated Cam Table (order separately from latch 36 (1.42 45 (1.77 36±4 (1.42±.15 +0.5 +.02 Ø 22.5 (.89 4 (.16 E5-6003 14 (.55 E5-6008 24 (.94 E5-6013 34 (1.34 E5-6018 6 (.24 E5-6004 16 (.63 E5-6009 26 (1.02 E5-6014 36 (1.42 E5-6019 8 (.31 E5-6005 18 (.71 E5-6010 28 (1.10 E5-6015 38 (1.50 E5-6020 10 (.39 E5-6006 20 (.79 E5-6011 30 (1.18 E5-6016 40 (1.57 E5-6021 12 (.47 E5-6007 22 (.87 E5-6012 32 (1.25 E5-6017 42 (1.65 E5-6022 If grip falls between two choices, use the smaller option (order lock core separately K Key options 0 No keys supplied (order separately, see page 130 3 1 Overmolded key supplied -0 23 (.91 -.00
E5 Cam Latch Zinc T-handle Hand operated Fixed grip 125 Ø 28 (1.10 L Lock Style Non-locking Latch (no cam 82.5 (3.25 key code CH751 22 (.88 key code R001 with shutter E5-9 - L F - UU1-1 K L Lock style 60 Non-locking (omit last two digits of part number 61 Keyed CH751 (lock core finish matches handle finish 62 Keyed R001 (stainless steel scalp shuttered 63 Without lock core (omit last two digits of part number Order lock core separately, see page 158 0.5 (.02 Sealing washer (compressed 27 (1.06 4 (.16 (order lock core separately +0.1 20.1-0 +.004 (.79 -.000 6 (.24 Max. 1 (.04 Min. F Finish 2 Bright chrome 5 Black powder coated 23 (.91 45 (1.77 36±4 (1.42±.15 +0.5 +.02 Ø 22.5 (.89-0 -.00 32 (1.25 K Key options 0 No keys supplied (order separately, see page 130 3 1 Overmolded key supplied Single hole install Multiple key codes Zinc alloy, powder coated or chrome plated and steel, zinc plated Maximum static load: 330 N (74 lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Installation Mounting nut: Maximum tightening torque: 10 N m (88 in lbf Screw: Maximum tightening torque: 10 N m (90 in lbf Keys Suitable for push-to-close action see page 128 For adjustable grip versions see page 134 For lock core selection and a complete overview of the SOUTHCO Key-Choice System see page 158 Selection Order latch and cam separately Cam Table (order separately from latch 4 (.16 E5-6003 14 (.55 E5-6008 24 (.94 E5-6013 34 (1.34 E5-6018 6 (.24 E5-6004 16 (.63 E5-6009 26 (1.02 E5-6014 36 (1.42 E5-6019 8 (.31 E5-6005 18 (.71 E5-6010 28 (1.10 E5-6015 38 (1.50 E5-6020 10 (.39 E5-6006 20 (.79 E5-6011 30 (1.18 E5-6016 40 (1.57 E5-6021 12 (.47 E5-6007 22 (.87 E5-6012 32 (1.25 E5-6017 42 (1.65 E5-6022 If grip falls between two choices, use the smaller option
126 E5 Cam Latch Zinc Wing style Fixed grip Single hole install Multiple key codes Easy finger grip Wing 21 (.83 56 (2.00 0.5 (.02 Sealing washer (compressed Wing: Zinc alloy, black powder coated and steel, zinc plated Maximum static load: 330 N (74 lbf Sealing NEMA 4 / IP65 achieved using gasket supplied Installation Mounting nut maximum tightening torque: 10 N m (88 in lbf Screw Maximum tightening torque: 5 N m (45 in lbf Keys Wing style suitable for push-toclose action see page 128 For lock core selection and a complete overview of the SOUTHCO Key-Choice System see page 158 Selection Order latch and cam separately Ø 28 (1.10 L Lock Styles Non-locking Latch (no cam key code CH751 19 (.75 key code R001 with shutter E5-9 - L 5 - UU1-1 K 27 (1.06 24 (.94 4 (.16 Ø8.5 (.33 lock core (order separately Padlockable 45 (1.77 L Lock style 30 Non-locking (omit last two digits of part number 31 black lock core keyed alike CH751 32 stainless steel scalp and shuttered lock core keyed alike R001 33 Without lock core (omit last two digits of part number Order lock core separately, see page 158 51 Padlockable, Type A clockwise to latch (omit last two digits in part number 52 Padlockable, Type B counter-clockwise to latch (omit last two digits in part number 23 (.91 Padlockable Version K Key options 0 No keys supplied (order separately, see page 130 3 1 Overmolded key supplied Cam E5-6 L G L Lock style 0 Non-locking or 1 Padlockable G G G G G 4 (.16 03 14 (.55 08 24 (.94 13 34 (1.34 18 6 (.24 04 16 (.63 09 26 (1.02 14 36 (1.42 19 8 (.31 05 18 (.71 10 28 (1.10 15 38 (1.50 20 10 (.39 06 20 (.79 11 30 (1.18 16 40 (1.57 21 12 (.47 07 22 (.87 12 32 (1.25 17 42 (1.65 22
E5 Cam Latch Zinc Cylinder lock Fixed grip 127 Cylinder Lock 6 (.24 0.5 (.02 Sealing washer (compressed Single hole install Latched / unlatched indicator Ø 28 (1.10 19 (.75 +0.1 20.1-0 +.004 (.79 -.000 27.2 (1.07 Mounting nut 4 (.16 36±4 (1.42±.15 Cam 45 (1.77 23 (.91 Zinc alloy, powder coated and steel, zinc plated Scalp stainless steel Maximum static load: 330 N (74 lbf Installation Mounting nut maximum tightening torque: 10 N m (88 in lbf Screw Maximum tightening torque: 5 N m (45 in lbf Sealing NEMA 4 / IP65 achieved using gasket supplied +0.5 +.02 Ø 22.5 (.89-0 -.00 Keys and Accessories 6 (.24 Max. 1 (.04 Min. Suitable for push-to-close action see page 128. See page 126 for cam part numbers F Finish 2 Bright chrome 5 Black powder coated Latch (no cam E5-5 - 40 F - UU1-1 K K Key options CH751 0 No keys supplied (order separately, see page 130 2 2 Flat keys supplied Selection Order latch and cam separately
128 E5 Cam Latch Zinc Push-to-close Hand, key or tool operated Single and two point Single hole installation Latched / unlatched indicator Push-to-close action Zinc alloy, powder coated and steel, zinc plated Maximum static load: 330 N (74 lbf Installation Mounting nut maximum tightening torque: 10 N m (88 in lbf Screw Maximum tightening torque: 5 N m (45 in lbf for two point actuator only Keys and Accessories Single Point: Push-to-close action in unlocked position only and key inserted (cylinder lock Two Point: Order actuator separately (see page 131 For lock core selection and a complete overview of the SOUTHCO Key-Choice System see page 158 Actuator See page 131 for details Two point to be used with SOUTHCO R4 rotary series latches and cables see page 272 Two point push to close action: Internal spring causes return of driver and actuator to original latched position when driver is released after opening. Ideal for use with cables and rotary latches. Single Point Spring-Loaded (Type A tool operated shown Ø 28 (1.10 Operation R Rotation Type A A Cam rotates clockwise to latch 18 (.70 Rotation identification 1. Push door towards frame 2. Ramp-shaped cam rotates as it contacts frame 3. Cam springs back and moves behind frame to achieve latching Type B 5 (.20 Cam rotates counter-clockwise to latch 31 (1.22 Two Point Spring-Loaded (Type A hand operated shown Ø 28 (1.10 Two Point Actuator for bare cable (order separately, see page 132 0.5 (.02 Sealing washer (compressed Mounting nut 8.3 (.32 +0.1 20.1 0 +.004 (.79 -.000 3.5 24.9 (.14 (.98 Mounting nut 21 (.83 24 (.79 21 (.83 33 (1.30 6 (.24 Max 1 (.04 Min 26±1.5 (.94±.06 (For single point only +0.5 Ø 22.5 (.89 55.4 (2.20 55.4 (2.20 0 +.02 -.00 Cable actuator (see notes 21 (.83 0.5 (.02 Sealing washer (compressed Two point actuator (order separately.5 (.02 Sealing Washer (compressed Two Point Actuator (order separately 20 (.79 Mounting Nut Cable Bracket AC Cable assembly, jacketed (see
129 Hand / Key Operated F Finish 2 Bright chrome (not available for wing type 5 Black powder coated T Type 5 Cylinder lock keyed alike CH751 9 Wing / T-handle / L-handle E5 - T - L F - R 0-1 K Selection Latch supplied fully assembled R Rotation 51 Type A single point (for visual identification cam stamped A or B 52 Type B single point (for visual identification cam stamped A or B TR Type A two point (order actuator separately TL Type B two point (order actuator separately K Key options 0 No keys supplied (order separately, see page 130 3 1 Overmolded key supplied L T = 5 T = 9 Lock style Cylinder Lock Wing T-handle L-handle Non-locking (omit last two digits of part number ~ 30 60 70 Keyed CH751 (lock core finish matches handle finish ~ 31 61 71 Keyed CH751 (stainless steel scalp shuttered 40 ~ ~ ~ Keyed R001 reversible (stainless steel scalp shuttered ~ 32 62 72 Without lock core (omit last two digits of part number (to be ordered separately see page 158 ~ 33 63 73 Tool Operated H Head Styles Slotted Hex recess 3 (.11 5 (.19 recess 216 electronics Recessed slot (tamper resistant Railway standard F Finish 2 Bright chrome 5 Black powder coated E5-6 - H F - R 0 Selection Latch supplied fully assembled H Head style 00 Slotted 01 Hex recess 02 03 04 05 06 3 (.11 07 5 (.19 08 recess 13 216 19 electronics 21 Recessed slot (tamper resistant 22 Railway standard R Rotation 51 Type A single point (for visual identification, cam stamped A or B 52 Type B single point (for visual identification, cam stamped A or B TR Type A two point (order actuator separately TL Type B two point (order actuator separately
130 E5 Cam Latch Accessories Keys and Flush Mount Bracket Tool key: Zinc alloy or nylon Overmolded key: Nickel plated and ABS plastic black Flat key: Nickel plated Keys Zinc or Nylon H Head style 2 3 (.11 3 4 7 8 recess 9 5 (.19 (nylon only 10 male (zinc only 11 electronics 12 216 (zinc only 14 Railway Standard (zinc only 56 (2.2 55 (2.2 F Finish 1 Plated zinc 2 Natural zinc 3 Nylon, black Head Styles 2 3 (.11 3 4 7 8 recess 9 5 (.19 E3 - H - F 10 male Overmolded key CH751: Single: PK-10-10-05 Pair: PK-10-01-05 Overmolded Keys Key CH751 Key R001 Flat Keys Key CH751 11 electronics 12 216 Overmolded key R001: Single: PK-10-10-05-KR001 Pair: PK-10-01-05-KR001 14 Railway Standard Flat key Pair: PK-10-01 Flush Mount Bracket 14 (.55 5.4 (.21 1.25 (.05 Stainless steel or galvanized steel with rubber o-ring For use with tool operated standard series cam latches, see pages 118-119, 121, 127 See page 91 for door preparation dimensions Compressed gasket O-ring thickness Total grip Flush bracket Ø 43 (1.69 20.1 (.79 Ø 5.4 (.21 58 (2.28 72 (2.84 A A Material 6.6 E5-77-1-12 Galvanized steel 6.6 E5-77-1-24 304 Stainless steel To calculate the Total, use the following formula: Thickness + Compressed Gasket - A. Use this Total with the appropriate E5 tables in the SOUTHCO Handbook to determine cam type.
E5 Cam Latch Accessories Multi-point actuators Dummy cam 131 Multi-Point Actuator Ø 6.1 (.24 18 (.7 51 (2.0 15.2 (.59 3.5 (.14 6 (.23 Zinc alloy Actuator plate (for multi-point see page 272 for cable assembly (Not recommended for Cylinder Lock version Not to be used with low profile E5 A5-91-201-11 Multi-Point Actuator - Low Profile 59 (2.32 23 (.9 23 (.9 17 (.66 2.4 (.09 Steel, plated Actuator plate (for multi-point see pages 198-199 for rods For use with all E5 latches Ø 6.2 (.24 17.2 (.67 A8-4-01-03 Multi-Point Actuator 22.2 (.87 4.6 (.18 Actuator plate 93.6 (3.68 8.1 (.31 18 (.7 28.8 (1.13 Adaptor Ø 8.6 (.33 x 18 (.7 deep Zinc alloy and steel, zinc plated Actuator plate (for multi-point see page 198 for rods Not to be used with low profile E5 A5-90-101-11 Dummy Cam 4 (.16 2X 8.1 (.32 Ø 17 (.67 8.5 (.33 Steel, stainless steel Replaces cam when used with actuator plate A5-90-101-11 in order to create a 2-point latching system 3.8 (.15 20 Steel Stainless Steel H3-0-45688 H3-0-45688-24
132 E5 Cam Latch Accessories Hooked cam Multi-point actuator Cable brackets Steel plated Hook cam: Steel, plated Multi-point actuator: Zinc alloy, plated Cable bracket: Steel, plated Not to be used with low profile E5 Hooked Cam 8.1 (.32 18 (.71 Ø 9.95 (.39 18 (.71 R4 R28 36 (.42 10 (.39 4 (.16 Hooked Cam E5-6200 No stop E5-6210 Stop for clockwise rotation E5-6220 Stop for counter-clockwise rotation Multi-Point Actuator 7.5 (.3 51 (2.0 36 (1.42 18 (.71 9 (.35 6 (.24 3.1 (.12 22 (.87 2X 8.1 Ø 3 18.1 (.71 A5-99-136 Cable Bracket Counter Clockwise Rotation Ø 22.5 (.88 38 (1.5 2X R20 4X Ø 6.4 (.25 2X 16 (.63 2X 17 (.67 52 (2.05 2X 20.1 (.79 32.4 (1.28 2X 25 55 (2.17 2 (.08 2X 43 AC-0-49617-11-L See page 272 for additional cable assembly selections Cable Bracket Clockwise Rotation Ø 22.5 (.88 38 (1.5 4X Ø 6.4 (.25 2X 16 (.63 2X 52 20.1 (.79 32.4 (1.28 2X 25 2 (.08 2X R20 55 (2.17 2X 43 2X 17 AC-0-49617-11-R
E5 Cam Latch Accessories Sealing cover Sealing washer Pull tab Padlock bracket 133 Sealing Cover Sealing Washer Ø 28.2 (1.11 47 (1.84 0.8 (.031 35 (1.38 28 (1.09 Sealing washer Ø 28.7 (1.13 11.7 (.46 6.9 (.27 Ø 22.5 (.875 19.6 (.77 Sealing washer: Neoprene natural Sealing cover: Thermoplastic elastomer, black Installation To provide sealing: use two sealing washers and add compressed thickness of each washer and accessory thickness to your door thickness range. Sealing washer for use with all E5 products Sealing cover for use with tool operated and cylinder lock E5 only Pull Tab 2.4 (.093 16 (.63 Shown perpendicular to latch cam Ø 22.6 (.89 20 (.79 20 (.79 32 (1.25 Ø 22.2 (.88 45 29 (1.78 (1.16 Shown in-line with latch cam Sealing washer Accessory Type Adjustment Formula Sealing washer E5-17 Add 0.4 (0.02 compressed height to door thickness Sealing cover 90-3 Add 2.3 (.090 to door thickness Padlock Bracket (Round Padlock Bracket ( Ø 11 (.43 42 (1.65 Ø 22.5 (.88 Ø 34 (1.34 24.5 (.96 2 (.08 Type Adjustment Formula Padlock bracket square E3-77-101-31 Add 2 (.08 to door thickness Padlock bracket round E3-77-102-31 Add 2 (.08 to door thickness Pull tab E5-18 Add 2.4 (.093 to door thickness 33 (1.30 2 (.08 Ø 22 (.87 25 (.98 Ø 11 (.43 Padlock bracket: Stainless steel, black powder coated Pull tab: Nylon, black Installation To provide sealing: use two sealing washers and add compressed thickness of each washer and accessory thickness to your door thickness range. Padlock brackets and pull tabs for use with tool operated and cylinder lock E5 only