ov-lifting_bolts_divider - Updated - 09-01-2017 Lifting Bolts
Technical Information roduct information Lifting Bolts roduct marking Compliant with 2006/42/EC, and with individual date of manufacture and batch number. Complies with 2006/42/CE Model No. Individual part no. date of manufacture Lifting angles Load 100% of load rating of bolt 45 Steel and Stainless steel (316) versions Load Approx 66% of load rating of bolt 60 Load Approx 50% of load rating of bolt For full information on lifting arrangements see technical pages Steel CE mark WLL weight limit Stainless (316L) Lifting Bolts from Automotion Components ov-lifting_bolts_product_information - Updated - 09-01-2017 Tel: 01483 26 67 76 Fax: 01483 26 67 75 web: mechanicalcomponents.co.uk a website from Automotion Components 743
Lifting Bolts Technical Information Installation information ov-lifting_bolts_installation_information - Updated - 09-01-2017 Lifting Bolts from Automotion Components Never use an oversized hook or other lifting device which will pry or tend to open the U shaped bar on centre pull hoist rings. After installation, check the hoist ring to be sure it swivels and pivots freely in all directions. The side of the ring must not contact anything. Always ensure full thread engagement when installing hoist rings. 744 Tel: 01483 26 67 76 Fax: 01483 26 67 75 web: mechanicalcomponents.co.uk a website from Automotion Components
Introduction Swivel Lifting Rings and Lifting Bolts Lifting Bolts Introduction to swivel lifting rings and Lifting Bolts (4002-4055) Our swivel lifting rings fully comply with the EC directive 2006/42/EC. They are CE marked and are supplied with a Certifi cate of Conformity. There is a 100% check on anti-cracking, a proof load test of 2.5 x load limit and a safety factor of 5 on most parts. Each ring is individually marked to ensure full product traceability. The Swivel Lifting Rings come in three main forms depending on the number of axis required to swivel. The most popular type is the double swivel rings. Single swivel Threads M8 M48 Loads 0,3 tons to 15 tons Double swivel Threads M4 M100 Loads 0,05 tons to 50 tons Triple swivel Threads M8 M56 Loads 0,3 tons to 22 tons Swivel lifting rings operating instructions. lease follow these instructions carefully. Ensure all lifting bolts are CE marked. Ensure they are handled by qualifi ed personnel. Refer to the operating instructions particularly with regards to product selection, any possibility of the load swivelling, the effect of lifting angles on the load capacity (see relevant tables), etc. Never allow any personnel underneath a suspended load. Always heed the load rating of the lifting bolt. Always perform a visual inspection of the lifting rings prior to use. Checking for any damage to thread and/or swivelling system. Check for wear or corrosion, signs of stress or bending. Check CE mark and load rating. Ensure a yearly full service inspection is performed. Always ensure the full bottom face of the lifting bolts is in contact with a smooth, square surface. Ensure bolt is tightened to the correct torque. Ensure full and unrestricted movement of the lifting ring in all directions. Before each lift ensure the correct orientation of the shackle in the lift direction. Avoid using our standard steel lifting rings in corrosive environments eg sandy, chemical, acid, moisture etc. In this case consider using our stainless steel lifting rings. Note the thread length requirements: - 1 x thread diameter for steel (ST37 min.). - 1.25 x thread diameter for cast iron. - 2 x thread diameter for aluminium. - 2.5 x thread diameter for other light metals. - If fi xing into low resistance material it is better to allow for a bigger diameter thread to compensate for the lower material resistance. Note: The full thread must be engaged. Longer thread lengths can be supplied on request or a bolt and washer/nut combination can be used. REORT OF THOROUGH EXAMINATION This report complies with the requirements of the Lifting Operations and Lifting Equipment Regulations 1998 Date of Thorough Examination: Sales Order number: Name and Address of customer for whom the thorough examination was made: Automotion Components Ltd Alexia House Description and identification of the equipment, including type, dimension and part number: Little Mead Industrial Estate Cranleigh Surrey GU6 8NE Quantity: Working Load Limit: in conjunction with this document. Original declaration of conformity is available on request Date of manufacture if known: Material: Was the examination carried out in accordance with an examination scheme: Batch : This part is CE marked in compliance with European Directive : Identification of any part found to have a defect which is or could become a danger to persons and a description of the defect: (If none state NONE) None. 2006/42/EC. YES NO articulars of any repair, renewal or alteration required to remedy the defect identified above: Is the above an existing or imminent danger to persons *Note-This is a reportable defect YES NO SECIMEN articulars of any tests carried out as part of the examination: (If none state NONE) Visual inspection and compliance. IS THIS EQUIMENT SAFE TO OERATE? YES NO Name of person making this report: Name of person authenticating this report: Latest date by which n N/A ov-lifting_bolts_rings_and_bolts - Updated -01-11-2017 Tel: 01483 26 67 76 Fax: 01483 26 67 75 web: mechanicalcomponents.co.uk a website from Automotion Components
Swivel Lifting Rings Safety Guide
Single swivel Threads M8 M48 Loads 0,3 tons to 15 tons Double swivel Threads M4 M100 Loads 0,05 tons to 50 tons Triple swivel Threads M8 M56 Loads 0,3 tons to 22 tons SECIMEN
4020 Threads M8 M30 Loads 0,3 tons to 3 tons. 4022 Threads M30 M45 Loads 3,5 tons to 6 tons. Complies with 2006/42/CE CE mark Model No. WLL weight limit Individual part no. date of manufacture 45 60 Never use an oversized hook or other lifting device which will pry or tend to open the U shaped bar on center pull hoist rings. Load Load Load 100% of load rating of bolt Approx 66% of load rating of bolt Approx 50% of load rating of bolt For full information on lifting arrangements see technical pages After installation, check the hoist ring to be sure it swivels and pivots freely in all directions. The side of the ring must not contact anything. Steel Stainless (316L) Always ensure full thread engagement when installing hoist rings. Also ensure face is flush.
α α
α α
α α
α α
Lifting Bolts Safety Guide
Standard Lifting Bolts Standard lifting bolts (to DIN 580 and DIN 582) (4040-4048) These are CE marked and are available with male or female threads in either steel or stainless steel (A4 AISI 316). They are meant only for use at a maximum angle of 45 from the thread. They are not meant for loads that might swivel. These are supplied with a generic Declaration of Conformity (DOC) stating that the parts have been manufactured to the relevant DIN standard and therefore suitable for lifting. Lifting Bolts Safety Overview 45 Do not lift Assembly instructions The lifting bolts are generally intended for permanent mounting to components such as motors, switchgear cabinets and gears, and for transporting these items of equipment 1. They must be used by qualifi ed personnel trained to current European Standards on the place of use. Lifting bolts must be permanently marked with a raised manufacturer s mark, material ID (e.g. C15E, A2 or A4), load-bearing capacity in axial direction (WLL in Kg), and with the CE symbol. Refer to the relevant table to determine the effect of lifting angles on the load capacity. 2. Check the fi xing points to ensure correct bolt seating, check for; corrosion, wear and tear, deformation etc. at regular intervals and before each use. 3. The fi xing point should be selected carefully such that the resultant forces are absorbed by the base material without any deformation. Screw-in depth for steel with a tensile strength of Rm >340 N/ mm², e.g. S235JR (1.0037); or GG 25 (0.6025 without cavities or shrinkage): 1.5 x thread diameter (=L). For screw-in material with lower strength, use fi xing points with greater screw-in length. Minimum screw-in depths recommended by the Liability Insurance Association: 2 x thread diameter in aluminum alloys 2.5 x thread diameter in light metal with low strength For light metals, non-ferrous metals and grey cast iron, select the thread such that the load-bearing capacity of the thread corresponds with the requirements involving the base material. For through-holes, a nut (0.8 x d) should be fully and fi rmly bolted from the opposite side. If the thread length of the screw is suffi cient, the use of an additional washer is recommended. 4. Select the location of fi xing points carefully to ensure that any rotational effects or load shifts are avoided. Arrange the fi xing point for a single strand sling perpendicularly above the center of the load. Arrange the fi xing points for a twin strand sling on both sides and above the load center. Caution: Avoid turning or rotating movements during the lift! osition the lifting bolt such that no shear tension acts on the bolt. Any introduced force must act in the direction of the eye bolt plane. Standard lifting bolts DIN 580 & DIN 582 4040-4048 5. The attachment surface must be fl at. Maximum spot-facing of the thread hole = nominal diameter of the thread. Blind holes must be drilled to a suffi cient depth to ensure that the contact surface of the eye bolt is fully seated. 6. Shock loads, tugs or vibrations may cause inadvertent loosening. Consider using a liquid thread lock agent such as Loctite making sure to observe the manufacturer s recommendations. Always secure bolts which remain permanently at the fi xing point, e.g. by glueing. 7. The end attachment must be freely moveable in the lifting bolt. When slinging and removing the end attachments (sling chain, round sling, wire rope), make sure that no pinch, shear, catch or impact points occur. Avoid damage to the end attachments caused by sharpedged loads. 8. Temperature suitability: these lifting bolts may be used without restricting or impairing the load-bearing capacity within the temperature range from -20 C to +200 C. 9. The seating surface of the bolts must not be allowed to make contact with corrosive chemicals, acids or their vapours. 10. After initial installation and at intervals depending on use, however at least once every year, the continued suitability of the fi xing point must be checked and inspected by an expert. This should also be done after any damage or other unusual incidents. If there is any doubt with regard to safe use, the fi xing point and/or the lifting equipment must not be used for safety reasons. No person should operate under a suspended load and operators should not be distracted or put in danger in the handling area. Failure to observe these instructions may result in personal injury and material damage! F 1 F 2 45 01483 26 67 74
4040 4043 4041 4044 4046 4048 F 1 Max. Kg F 2 Max. Kg F 1 Max. Kg F 2 Max. Kg F 1 Max. Kg F 2 Max. Kg M6 70 50 70 50 70 50 70 50 1/4 70 50 69 50 M8 140 100 140 100 140 100 140 100 5/16 140 95 140 95 M10 230 170 230 170 230 170 230 170 3/8 230 170 230 170 M12 340 240 340 240 340 240 340 240 1/2 340 240 340 240 M14 340 240 340 240 340 240 340 2400 5/8 700 500 700 500 M16 700 500 700 500 700 500 700 500 3/4 1200 830 1200 830 M18 700 500 700 500 700 500 700 500 7/8 1500 1050 1500 1050 M20 1200 860 1200 860 1200 860 1200 860 1 1800 1270 1800 1270 M22 1200 830 1200 830 1200 830 1200 830 1-1/8 2500 1650 2500 1650 M24 1800 1290 1800 1290 1800 1290 1800 1290 1-1/4 4300 3200 4300 3200 M27 1800 1270 1800 1270 1800 1270 1800 1270 1-1/2 6100 4300 6100 4300 M30 3200 2300 3200 2300 3200 2300 3200 2300 1-3/4 8000 5500 8000 5500 F 1 Max. Kg F 2 Max. Kg M33 3600 3600 3600 3600 3600 3600 3600 3600 M36 4600 3300 4600 3300 4600 3300 4600 3300 M39 5100 3700 5100 3700 5100 3700 5100 3700 M42 6300 4500 6300 4500 6300 4500 6300 4500 M45 7000 5000 7000 5000 7000 5000 7000 5000 M48 8600 6100 8600 6100 8600 6100 8600 6100 M56 11500 8200 - - 11500 8200 - - M64 16000 11000 - - 16000 11000 - - M72 x 6 20000 14000 - - 20000 14000 - - M80 x 6 28000 20000 - - 28000 20000 - - M100 x 6 40000 29000 - - 40000 29000 - - * F 1 Max. Kg F 2 Max. Kg F 1 Max. Kg F 2 Max. Kg 2 9000 7300 9000 7300 2-1/4 11500 8300 11500 8300 2-1/2 16000 11000 16000 11000 *For UNC, BS & BSW threads. www.automotioncomponents.co.uk
Auto 0496 Web: www.automotioncomponents.co.uk Tel.: 01483 26 67 74 Fax: 01483 26 67 75 Email: info@automotioncomponents.co.uk Due diligence has been taken in preparing these safety instructions. Automotion Components Ltd can not be held legally responsible nor liable for any missing or incorrect information and the ensuing consequences. Automotion Components Ltd reserves the right, without prior notice to effect modifi cations and design changes to these products and associated documentation as part of a continuous program of product development.
Steel Male Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4040 Material Forged steel (C15E) annealed and zinc plated. Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 580. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread is fully screwed in, and the material it is being used in is as least as strong as the that of the bolt. Temperature range -20 C to +200 C. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg l 4040.060-Z Coarse M 6 36 36 20 20 8 70 50 0,05 13,0 4040.080-Z Coarse M 8 36 36 20 20 8 140 95 0,06 13,0 4040.100-Z Coarse M10 45 45 25 25 10 230 170 0,11 17,0 4040.120-Z Coarse M12 53 54 30 30 12 340 240 0,18 20,5 4040.140-Z Coarse M14 62 63 35 35 14 340 240 0,18 27,0 4040.160-Z Coarse M16 62 63 35 35 14 700 500 0,28 27,0 4040.180-Z Coarse M18 71 72 40 40 14 700 500 0,43 30,0 4040.200-Z Coarse M20 71 72 40 40 16 1200 830 0,45 30,0 4040.220-Z Coarse M22 71 72 40 40 16 1200 830 0,45 30,0 4040.240-Z Coarse M24 90 90 50 50 20 1800 1270 0,74 36,0 4040.270-Z Coarse M27 109 108 65 60 24 1800 1270 0,93 45,0 4040.300-Z Coarse M30 109 108 65 60 24 3200 2300 1,66 45,0 4040.330-Z Coarse M33 128 126 75 70 28 3600 3600 2,60 54,0 4040.360-Z Coarse M36 128 126 75 70 28 4600 3300 2,65 54,0 4040.390-Z Coarse M39 147 144 85 80 32 5100 3700 3,87 63,0 4040.420-Z Coarse M42 147 144 85 80 32 6300 4500 4,03 63,0 4040.450-Z Coarse M45 168 166 100 90 38 7000 5000 6,15 68,0 4040.480-Z Coarse M48 168 166 100 90 38 8600 6100 6,38 68,0 4040.560-Z Coarse M56 187 184 110 100 42 11500 8200 8,80 78,0 4040.640-Z Coarse M64 208 206 120 110 48 16000 11000 12,4 90,0 4040.720-Z Coarse M72 x 6 260 260 150 140 60 20000 14000 23,3 100,0 4040.800-Z Coarse M80 x 6 298 296 170 160 68 28000 20000 34,2 112,0 4040.999-Z Coarse M100 x 6 330 330 190 180 75 40000 29000 49,1 130,0 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Male Lifting Eye Bolts metric sizes Lifting Bolts & Shackles Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg l 4040.120-015-Z Fine M12 x 1,5 53 54 30 30 12 340 240 0,18 20,5 4040.160-015-Z Fine M16 x 1,5 62 63 35 35 14 700 500 0,28 27,0 4040.200-020-Z Fine M20 x 2,0 71 72 40 40 16 1200 830 0,45 30,0 4040.240-020-Z Fine M24 x 2,0 90 90 50 50 20 1800 1270 0,74 36,0 4040.300-020-Z Fine M30 x 2,0 109 108 65 60 24 3600 2600 1,66 45,0 4040.360-030-Z Fine M36 x 3,0 128 126 75 70 28 5100 3700 2,58 54,0 4040.420-030-Z Fine M42 x 3,0 147 144 85 80 32 7000 5000 3,95 63,0 4040.480-030-Z Fine M48 x 3,0 168 166 100 90 38 8600 6100 6,38 68,0 4040.560-040-Z Fine M56 x 4,0 187 184 110 100 42 11500 8300 8,48 78,0 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Female Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4041 Material Forged steel (C15E) annealed and zinc plated. Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 582. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. Temperature range -20 C to +200 C. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg 4041.060-Z Coarse M 6 36 36 20 20 8 70 50 0,05 4041.080-Z Coarse M 8 36 36 20 20 8 140 95 0,05 4041.100-Z Coarse M10 45 45 25 25 10 230 170 0,09 4041.120-Z Coarse M12 53 54 30 30 12 340 240 0,16 4041.140-Z Coarse M14 62 63 35 35 14 340 240 0,24 4041.160-Z Coarse M16 62 63 35 35 14 700 500 0,24 4041.180-Z Coarse M18 71 72 40 40 16 700 700 0,35 4041.200-Z Coarse M20 71 72 40 40 16 1200 830 0,36 4041.220-Z Coarse M22 71 72 40 40 16 1200 830 0,36 4041.240-Z Coarse M24 90 90 50 50 20 1800 1270 0,72 4041.270-Z Coarse M27 90 90 50 50 20 1800 1270 0,72 4041.300-Z Coarse M30 109 108 65 60 24 3200 2300 1,32 4041.330-Z Coarse M33 109 108 65 60 24 3600 2600 1,30 4041.360-Z Coarse M36 128 126 75 70 28 5100 3700 2,08 4041.390-Z Coarse M39 128 126 75 70 28 5100 3700 2,08 4041.420-Z Coarse M42 147 144 85 80 32 7000 4500 3,11 4041.450-Z Coarse M45 147 144 85 80 32 7000 5000 3,16 4041.480-Z Coarse M48 168 166 100 90 38 8600 6100 5,02 4041.560-Z Coarse M56 187 184 110 100 42 11500 8200 6,70 4041.640-Z Coarse M64 208 206 120 110 48 16000 11000 9,30 4041.720-Z Coarse M72x6 260 260 150 140 60 20000 14000 18,5 4041.800-Z Coarse M80x6 298 296 170 160 68 28000 20000 27,3 4041.999-Z Coarse M100x6 330 330 190 180 75 40000 29000 26,4 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Female Lifting Eye Bolts metric sizes Lifting Bolts & Shackles Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg 4041.160-015-Z Fine M16 x 1,5 62 63 35 35 14 700 500 0,24 4041.200-020-Z Fine M20 x 2,0 71 72 40 40 16 1200 830 0,36 4041.240-020-Z Fine M24 x 2,0 90 90 50 50 20 1800 1270 0,72 4041.300-020-Z Fine M30 x 2,0 109 108 65 60 24 3600 2600 1,32 4041.360-030-Z Fine M36 x 3,0 128 126 75 70 28 5100 3700 2,08 4041.420-030-Z Fine M42 x 3,0 147 144 85 80 32 7000 5000 3,11 4041.480-030-Z Fine M48 x 3,0 168 166 100 90 38 8600 6100 5,02 4041.560-040-Z Fine M56 x 4,0 187 184 110 100 42 11500 8300 6,69 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Stainless Male Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4043 Material Stainless steel (A4, AISI 316). CE marked. Technical notes To DIN 580. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Material d 1 l h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg 4043.060-A4 A4 s/s M 6 13,0 36 36 20 20 8 70 50 0,05 4043.080-A4 A4 s/s M 8 13,0 36 36 20 20 8 140 95 0,06 4043.100-A4 A4 s/s M10 17,0 45 45 25 25 10 230 170 0,11 4043.120-A4 A4 s/s M12 20,5 53 54 30 30 12 340 240 0,18 4043.160-A4 A4 s/s M16 27,0 62 63 35 35 14 700 500 0,28 4043.200-A4 A4 s/s M20 30,0 71 72 40 40 16 1200 860 0,45 4043.240-A4 A4 s/s M24 36,0 90 90 50 50 20 1800 1270 0,74 4043.300-A4 A4 s/s M30 45,0 109 108 65 60 24 3200 2300 1,66 4043.360-A4 A4 s/s M36 54,0 128 126 75 70 28 4600 3300 2,65 4043.420-A4 A4 s/s M42 63,0 147 144 85 80 32 6300 4500 4,03 4043.480-A4 A4 s/s M48 68,0 168 166 100 90 38 8600 6100 6,38 4043.060-A2 A2 s/s M 6 11,0 31 36 20 16 8 70 50 0,05 4043.080-A2 A2 s/s M 8 13,0 36 36 20 20 8 140 95 0,06 4043.100-A2 A2 s/s M10 17,0 45 45 25 25 10 230 170 0,11 4043.120-A2 A2 s/s M12 20,5 53 54 30 30 12 340 240 0,18 4043.160-A2 A2 s/s M16 27,0 62 63 35 35 14 700 500 0,28 4043.200-A2 A2 s/s M20 30,0 71 72 40 40 16 1200 860 0,45 4043.240-A2 A2 s/s M24 36,0 90 90 50 50 20 1800 1290 0,74 4043.300-A2 A2 s/s M30 45,0 109 108 65 60 24 3200 3200 1,66 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Stainless Female Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4044 Material Stainless steel (A4, AISI 316). CE marked. Technical notes To DIN 582. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Material d 1 h w 1 d 2 w 2 W 3 F 1 max. Kg F 2 max. Kg X Kg 4044.060-A4 A4 s/s M 6 36 36 20 20 8 70 50 0,05 4044.080-A4 A4 s/s M 8 36 36 20 20 8 140 95 0,05 4044.100-A4 A4 s/s M10 45 45 25 25 10 230 170 0,09 4044.120-A4 A4 s/s M12 53 54 30 30 12 340 240 0,16 4044.160-A4 A4 s/s M16 62 63 35 35 14 700 500 0,24 4044.200-A4 A4 s/s M20 71 72 40 40 16 1200 860 0,36 4044.240-A4 A4 s/s M24 90 90 50 50 20 1800 1270 0,72 4044.300-A4 A4 s/s M30 109 108 65 60 24@ 3200 2300 1,32 4044.360-A4 A4 s/s M36 128 126 75 70 28 4600 3300 2,08 4044.420-A4 A4 s/s M42 147 144 85 80 32 6300 4500 3,11 4044.480-A4 A4 s/s M48 168 166 100 90 38 8600 6100 5,02 4044.060-A2 A2 s/s M 6 31 36 20 16 8,5@ 70 50 0,03 4044.080-A2 A2 s/s M 8 36 36 20 20 8,5 140 95 0,05 4044.100-A2 A2 s/s M10 45 45 25 25 10 230 170 0,09 4044.120-A2 A2 s/s M12 53 54 30 30 11 340 240 0,16 4044.160-A2 A2 s/s M16 62 63 35 35 13 700 500 0,24 4044.200-A2 A2 s/s M20 71 72 40 40 16 1200 860 0,36 4044.240-A2 A2 s/s M24 90 90 50 50 20 1800 1270 0,72 4044.300-A2 A2 s/s M30 109 108 65 60 25 3200 2300 1,32 4044.360-A2 A2 s/s M36 128 126 75 70 30 4600 3300 2,08 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Male Lifting Eye Bolts inch sizes Lifting Bolts & Shackles 4046 Material Forged steel (C15E) annealed and zinc-plated (-Z). Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 580. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. d 1 Thread type d 2 w 1 w 2 w 3 l 1 h F 1max. Kg F 2max. Kg X Kg 4046.U1/4-Z 1/4$-20 UNC 20 36 20 8 13,0 36 70 50 0,06 4046.U5/16-Z 5/16$-18 UNC 20 36 20 8 13,0 36 140 95 0,06 4046.U3/8-Z 3/8$-16 UNC 25 45 25 10 17,0 45 230 170 0,11 4046.U1/2-Z 1/2$-12 UNC 30 54 30 12 20,5 53 340 240 0,18 4046.U5/8-Z 5/8$-11 UNC 35 63 35 14 27,0 62 700 500 0,28 4046.U3/4-Z 3/4$-10 UNC 40 72 40 16 30,0 71 1200 830 0,45 4046.U7/8-Z 7/8$-9 UNC 50 90 50 20 36,0 90 1500 1050 0,74 4046.U1-Z 1$-8 UNC 50 90 50 20 36,0 90 1800 1270 0,74 4046.U1-1/8-Z 1-1/8$-7 UNC 65 108 60 24 45,0 109 2500 1650 1,66 4046.U1-1/4-Z 1-1/4$-7 UNC 75 126 70 28 54,0 128 4300 3200 2,65 4046.U1-1/2-Z 1-1/2$-6 UNC 85 144 80 32 63,0 147 6100 4300 4,03 4046.U1-3/4-Z 1-3/4$-5 UNC 100 166 90 38 68,0 168 8000 5500 6,38 4046.U2-Z 2$ UNC 100 166 90 38 68,0 168 9900 7300 6,38 4046.U2-1/4-Z 2-1/4$ UNC 110 184 100 42 78,0 187 11500 8300 8,80 4046.U2-1/2-Z 2-1/2$ UNC 120 206 110 48 90,0 208 16000 11000 12,40 4046.G1/4-Z 1/4$-19 BS 35 63 35 14 27,0 62 70 50 0,28 4046.G3/8-Z 3/8$-19 BS 40 72 40 16 30,0 71 230 170 0,45 4046.G1/2-Z 1/2$-14 BS 50 90 50 20 36,0 90 340 240 0,74 4046.G5/8-Z 5/8$-14 BS 50 90 50 20 36,0 90 700 500 0,74 4046.G3/4-Z 3/4$-14 BS 65 108 60 24 45,0 109 1200 830 1,66 4046.G7/8-Z 7/8$-14 BS 65 108 60 24 45,0 109 1500 1050 1,66 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Male Lifting Eye Bolts inch sizes Lifting Bolts & Shackles Order No. d 1 Thread type d 2 w 1 w 2 w 3 l 1 h F 1max. Kg F 2max. Kg X Kg 4046.G1-Z 1$-11 BS 75 126 70 28 54,0 128 1800 1270 2,56 4046.G1-1/8-Z 1-1/8$-11 BS 85 144 80 32 63,0 147 2500 1650 4,03 4046.G1-1/4-Z 1-1/4$-11 BS 85 144 80 32 63,0 147 4300 3200 4,03@ 4046.G1-1/2-Z 1-1/2$-11 BS 100 166 90 38 68,0 168 6100 4300 6,38@ 4046.G1-3/4-Z 1-3/4$-11 BS 110 184 100 42 78,0 187 8000 5500 8,80 4046.G2-Z 2$ BS 120 206 110 48 90,0 208 9900 7300 12,40 4046.W1/4-Z 1/4$-20 BSW 20 36 20 8 13,0 36 70 50 0,06 4046.W5/16-Z 5/16$-18 BSW 20 36 20 8 13,0 36 140 95 0,06 4046.W3/8-Z 3/8$-16 BSW 25 45 25 10 17,0 45 230 170 0,11 4046.W1/2-Z 1/2$-12 BSW 30 54 30 12 20,5 53 340 240 0,18 4046.W5/8-Z 5/8$-11 BSW 35 63 35 14 27,0 62 700 500 0,28 4046.W3/4-Z 3/4$-10 BSW 40 72 40 16 30,0 71 1200 830 0,45 4046.W7/8-Z 7/8$-9 BSW 50 90 50 20 36,0 90 1500 1050 0,74 4046.W1-Z 1$-8 BSW 50 90 50 20 36,0 90 1800 1270 0,74 4046.W1-1/8-Z 1-1/8$-7 BSW 65 108 60 24 45,0 109 2500 1650 1,66 4046.W1-1/4-Z 1-1/4$-7 BSW 75 126 70 28 54,0 128 4300 3200 2,65 4046.W1-1/2-Z 1-1/2$-6 BSW 85 144 80 32 63,0 147 6100 4300 4,03 4046.W1-3/4-Z 1-3/4$-5 BSW 100 166 90 38 68,0 168 8000 5500 6,38 4046.W2-Z 2$ BSW 100 166 90 38 68,0 168 9900 7300 6,38 4046.W2-1/4-Z 2-1/4$ BSW 110 184 100 42 78,0 187 11500 8300 8,80 4046.W2-1/2-Z 2-1/2$ BSW 120 206 110 48 90,0 208 16000 11000 12,40 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Female Lifting Eye Bolts inch sizes Lifting Bolts & Shackles 4048 Material Forged steel (C15E) annealed and zinc plated. Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 582. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. d 1 Thread type d 2 w 1 w 2 h k F 1max. Kg F 2max. Kg X Kg 4048.U1/4-Z 1/4$-20 UNC 20 36 20 8 36 70 50 0,05 4048.U5/16-Z 5/16$-18 UNC 20 36 20 8 36 140 95 0,05 4048.U3/8-Z 3/8$-16 UNC 25 45 25 10 45 230 170 0,09 4048.U1/2-Z 1/2$-13 UNC 30 54 30 12 53 340 240 0,16 4048.U5/8-Z 5/8$-11 UNC 35 63 35 14 62 700 500 0,24 4048.U3/4-Z 3/4$-10 UNC 40 72 40 16 71 1200 830 0,36 4048.U7/8-Z 7/8$-9 UNC 50 90 50 20 90 1500 1050 0,72 4048.U1-Z 1$-8 UNC 50 90 50 20 90 1800 1270 0,72 4048.U1-1/8-Z 1-1/8$-7 UNC 65 108 60 24 109 2500 1650 1,32 4048.U1-1/4-Z 1-1/4$-7 UNC 75 126 70 28 128 4300 3200 2,08 4048.U1-1/2-Z 1-1/2$-6 UNC 85 144 80 32 147 6100 4300 3,11 4048.U1-3/4-Z 1-3/4$-5 UNC 100 166 90 38 168 8000 5500 5,02 4048.U2-Z 2$ UNC 100 166 90 38 168 9900 7300 5,02 4048.U2-1/4-Z 2-1/4$ UNC 110 184 100 42 187 11500 8300 6,69 4048.U2-1/2-Z 2-1/2$ UNC 120 206 110 48 208 16000 11000 9,30 4048.G1/4-Z 1/4$-19 BS 30 54 30 53 12 70 50 0,16 4048.G3/8-Z 3/8$-19 BS 35 63 35 62 14 230 170 0,24 4048.G1/2-Z 1/2$-14 BS 40 72 40 71 16 340 240 0,36 4048.G5/8-Z 5/8$-14 BS 40 72 40 71 16 700 500 0,36 4048.G3/4-Z 3/4$-14 BS 50 90 50 90 20 1200 830 0,72 4048.G7/8-Z 7/8$-14 BS 65 108 60 109 24 1500 1050 1,32 4048.G1-Z 1$-11 BS 65 108 60 109 24 1800 1270 1,32 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Steel Female Lifting Eye Bolts inch sizes Lifting Bolts & Shackles Order No. d 1 Thread type d 2 w 1 w 2 h k F 1max. Kg F 2max. Kg X Kg 4048.W1/4-Z 1/4$-20 BSW 20 36 20 36 8 70 50 0,05 4048.W5/16-Z 5/16$-18 BSW 20 36 20 36 8 140 95 0,05 4048.W3/8-Z 3/8$-16 BSW 25 45 25 45 10 230 170 0,09 4048.W1/2-Z 1/2$-13 BSW 30 54 30 53 12 340 240 0,16 4048.W5/8-Z 5/8$-11 BSW 35 63 35 62 14 700 500 0,24 4048.W3/4-Z 3/4$-10 BSW 40 72 40 71 16 1200 830 0,36 4048.W7/8-Z 7/8$-9 BSW 50 90 50 90 20 1500 1050 0,72 4048.W1-Z 1$-8 BSW 50 90 50 90 20 1800 1270 0,72 4048.W1-1/8-Z 1-1/8$-7 BSW 65 108 60 109 24 2500 1650 1,32 4048.W1-1/4-Z 1-1/4$-7 BSW 75 126 70 128 28 4300 3200 2,08 4048.W1-1/2-Z 1-1/2$-6 BSW 85 144 80 147 32 6100 4300 3,11 4048.W1-3/4-Z 1-3/4$-5 BSW 100 166 90 168 38 8000 5500 5,02 4046.W2-Z 2$ BSW 100 166 90 168 38 9900 7300 5,02 4046.W2-1/4-Z 2-1/4$ BSW 110 184 100 187 42 11500 8300 6,69 4046.W2-1/2-Z 2-1/2$ BSW 120 206 110 208 48 16000 11000 9,30 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Clamping Nuts Lifting Bolts & Shackles 4180 Material Steel (C35N) zinc plated, or stainless steel (AISI 316, 1.4571). Technical notes To DIN 28129. Order No. Material d 1 d 2 d 3 w l 1 l 2 l 3 X Kg 4180.012 Steel M12 14 100 48 25 50 0,45 35 4180.016 Steel M16 14 100 48 25 50 0,46 35 4180.020 Steel M20 16 100 50 28 50 0,63 40 4180.024 Steel M24 18 100 55 32 50 0,80 45 4180.027 Steel M27 20 100 58 35 50 1,00 50 4180.030 Steel M30 20 100 58 35 50 1,00 50 4180.012-A4 Stainless M12 14 100 48 25 50 0,45 35 4180.016-A4 Stainless M16 14 100 48 25 50 0,46 35 4180.020-A4 Stainless M20 16 100 50 28 50 0,63 40 4180.024-A4 Stainless M24 18 100 55 32 50 0,80 45 4180.027-A4 Stainless M27 20 100 58 35 50 1,00 50 4180.030-A4 Stainless M30 20 100 58 35 50 1,00 50 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk
Clamping Levers Lifting Bolts & Shackles 4182 Material Steel (St. 37) zinc plated, or stainless steel (A2, AISI 303 or A4 AISI 316). Order No. Material d l 4182.008 Steel M 8 0,04 63 4182.010 Steel M10 0,07 80 4182.012 Steel M12 0,14 100 4182.016 Steel M16 0,28 125 4182.020 Steel M20 0,56 160 4182.008-A2 A2 Stainless M 8 0,04 63 4182.010-A2 A2 Stainless M10 0,07 80 4182.012-A2 A2 Stainless M12 0,14 100 4182.016-A2 A2 Stainless M16 0,28 125 4182.020-A2 A2 Stainless M20 0,56 160 X Kg 4182.008-A4 A4 Stainless M 8 0,04 63 4182.010-A4 A4 Stainless M10 0,07 80 4182.012-A4 A4 Stainless M12 0,14 100 4182.016-A4 A4 Stainless M16 0,28 125 4182.020-A4 A4 Stainless M20 0,56 160 Tel: 0845 850 99 40 Fax: 0845 850 99 41 Email: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk