FLASHLIGHT ANSI STANDARDS

FLASHLIGHT ANSI STANDARDS While Pelian was one of the first manufaturers to use quantifiable test proedures, the need was reognized to develop a ommon language that ustomers ould use to selet the right flashlight for their speifi needs. As a result, the Amerian National Standards Institute (ANSI) with input from the flashlight industry, developed performane standards and symbols to effetively ommuniate a flashlight's features and benefits. Resulting ANSI/NEMA FL 1 Standards inlude the six riteria desribed below: LIGHT OUTPUT Light Output is the total luminous flux. It is the total quantity of emitted overall light energy as measure by integrating the entire angular output of the portable light soure. Light output in this standart is expressed in units of lumens. RUN TIME Run Time is defined as the duraton of time from the initial light output value defined as 30 seons after the point the devie is first turned on using fresh batteries, until the light output reahes 10% of the initial value. BEAM DISTANCE Beam Distane is defined as the distane from the devie at whih the light beam is 0.25 lux (0.25 lux is approximately the equivalent of the light emitted from the full moon "on a lear night in an open field"). PEAK BEAM INTENSITY Peak Beam Intensity is the maximum luminous intensity typially along the entral axis of a one of light. The value is reported in andela and does not hange with distane. IMPACT RESISTANCE Impat Resistane is the degree to whih a devie resists damage from dropping on a solid surfae. IPX4 WATER PENETRATION RATINGS IPX4 - Water Resistane - Water splashed against the devie from any diretion shall have no harmful effets. IPX4 / IPX7 WATER PENETRATION RATINGS IPX7 - Water Proof - Ingress of water in quantities ausing harmful effets shall not be possible when the enlosure is temporarily immersed in water under standardized onditions of pressure and time. IPX8 - Submersible - Ingress of water in quantities ausing harmful effets shall not be possible when the enlosure is ontinuously immersed in water under onditions whih shall be stated by manufaturer, but whih are more severe than for IPX7.

ANSI (AMERICAN NATIONAL STANDARDS INSITUTE) These standards are aredited by ANSI, whih is a private non-profit organization that oversees the development of voluntary onsensus standards for produts, servies, proesses, systems, and personnel in the United States. The organization also oordinates U.S. standards with international standards so Amerian produts an be used globally. GLOSSARY OF TERMS Candela - A unit of measurement of the intensity of light that is, power emitted by a light soure in a partiular diretion. Lux - The unit of luminous flux in the International System, equal to the amount of light given out through a solid angle by a soure of one andela intensity radiating equally in all diretions. Lumen - A unit of measurement of the amount of brightness that omes from a light soure. Lumens define "luminous flux," whih is energy within the range of frequenies we pereive as light. Integrating Sphere - An integrating sphere is a measurement devie with an entrane port that an aept all the diretional light output of the devie under test, or an totally enlose the devie itself. The walls of the sphere should be highly diffuse with high refletivity (>80%) and the spetroradiometer should be shielded from diret view of the devie under test by a baffle system. IP (Ingress Protetion) - Ingress Protetion (IP) ratings speify the environmental protetion the enlosure provides. The IP rating normally has two numbers (IPXX). The first number represents protetion from solid objets or materials (dust) where the seond number represents protetion from liquids (water). With the IP rating IP 54, 5 desribes the level of protetion from solid objets and 4 desribes the level of protetion from liquids.

File E184884 Projet 98NK16439 1998-08-27 REPORT on FLASHLIGHTS AND LANTERNS, FOR USE IN HAZARDOUS LOCATIONS Pelian Produts In. Torrane, CA

DESCRIPTION PRODUCT COVERED: USL - Flashlight, Model Pelilite 1800 for use in Class I, Division 2, Group D Hazardous Loations. GENERAL: The flashlight noted above is not provided with a lamp disonnet mehanism. ENGINEERING CONSIDERATIONS (NOT FOR FIELD REPRESENTATIVE'S USE): USL, indiates investigation to United States Standard UL 783, Sixth Edition. MARKING: The following marking is molded on the external surfae of the flashlight ase. * 1. Listee's name. 2. Catalog number. 3. Designation of the Hazardous Loations as shown in "Produt Covered." 4. The designation of the lamp bulb to be used and the number, type and size of batteries to be employed. 5. Temperature Code T3. 6. The word "WARNING" and the following or equivalent statement: "Risk of ignition - Do not open in a hazardous area." ASSEMBLY AND CONSTRUCTION DETAILS: The general assembly of the devie is shown on Figs. 1 and 2. Certain other subassemblies are shown on additional illustrations. All dimensions are approximate unless otherwise stated. Assembled devie is shown in Fig. 1.

FLASHLIGHT MODEL SUPER PELILITE 1800 - FIG. 1 (N98-9375) Fig. 1 shows a piture of the devie fully assembled. For use with two size "C" dry ell alkaline batteries and Cat. No. 1804, Carley Xenon lamp module.

FLASHLIGHT MODEL SUPER PELILITE 1800 - FIG. 2 1. Shroud - ABS, shape and dimensions as shown in ILL. 2. Alternate - Thermoplasti rubber, material name Rimflex, Compound No. A/AG38B, manufatured by Rimpat International In. Shape and dimension as shown in ILL. 2A. Alternate - Thermoplasti rubber, material name Rimflex, Type A/OM55TPE manufatured by Rimpat International In. Alternate - Thermoplasti rubber, shape and dimensions as shown in ILL. 2B. 2. Lens - Bayer Mobay, Makrolon 2500. A 1.14 in. deep up with minimum thikness of not less than 0.15 in. and an internal diameter of 1.495 in. Lens fits into shroud with snap in motion. See ILL. 3. Alternate Same as above, exept GE, Lexan HF1130, ILL. 3A. Alternate - GE Lexan HF1130. A 0.93 in. deep up with minimum wall thikness of not less than 0.17 in. and an internal diameter of 1.48 in. Lens fit into shroud with snap in motion. See ILL. 3B 3. Lamp Module - Cat. No. 1804, mahined aluminum refletor with smooth aluminized surfae with Xenon bulb rated 2.5 V, 0.74 A, seured in the refletor with erami Saueveisen No. 8 ement. Lamp module omes fully assembled from vendor, manufatured by Carley Lamp In. See ILL. 4. Alternate Manufatured by Illumination Tehnology Industries, with polyarbonate refletor with mirror finish, with Xenon bulb rated 2.6 V, 0.74 A. See ILL. 4A. 4. Battery Retainer - 302 Stainless steel. Shape and dimensions as shown. See ILL. 5. 5. Spring (Battery Contat) - 302 Stainless steel. Spot welded to the battery retainer. See ILL. 6. 6. Foam Pad - Plaed around the battery ontat spring. See ILL. 7. 7. Body - ABS. Shape and dimension as shown in ILL. 8. 8. End Cap - ABS, fits on the bottom of the body. Shape and dimension as shown in ILL. 9.

Certifiate of Compliane Certifiate: 1640694 Master Contrat: 154507 Projet: 2657098 Date Issued: January 3, 2014 Issued to: Pelian Produts, Inorporated The produts listed below are eligible to bear the CSA Mark shown Issued by: Ezio Migliozi Ezio Migliozi PRODUCTS CLASS 9098 01 - MISCELLANEOUS - For Hazardous Loations Class I, Div 2, Groups A, B, C and D (Non-Inendive); Class II, Div 2, Groups F and G; Class III. Handheld flashlight Model "Poket Sabre 2C" Cat No 1820, to be used with two (2) "C" size batteries 1.5V per ell by "Eveready No E93 or Duraell MN1400 or Ray-O-Va No 813 and lamp Cat. No.1804, P/N 1803-350-000. Temp Code T3C. Ambient: 35 C to +40 C. Handheld flashlight Model "Magnum Plus-2AA" Cat No 2340 to be used with two (2) "AA" size batteries 1.5V per ell, by Eveready No E91 or Duraell MN1500 or PC1500 or Ray-O-Va Al-AA or 815 with lamp Module CAT # 2304; Temp. Code T3C. Ambient: 35 C to +40 C. Handheld flashlight Model "Heads-Up" Cat No 2600, for use with four (4) size "AA", 1.5V eah, battery ells by Eveready No E91 or Duraell MN1500 or PC1500 or Ray-O-Va No 815 and light bulb Cat No 2604 or 2605, Temp Code T3C. Handheld flashlight Cat No 8040 M10 to be used with two (4) "C" size batteries, 1.5V per ell by Eveready No E93 or Duraell MN1400 with Lamp Module Cat. No. 8044, P/N 8043-350-000; Temp. Code T3C. Ambient: 35 C to +40 C. Class I, Div. 2, Groups A, B, C and D (Non-inendive); Class II, Div. 2, Group G:

Certifiate: 1640694 Master Contrat: 154507 Projet: 2657098 Date Issued: January 3, 2014 Handheld flashlight Model "Super Pelilite" Cat No 1800, to be used with two (2) "C" size batteries, 1.5V eah per ell by "Eveready No E93 or "Eveready No CH35 or Duraell MN1400 or PC1400 or Ray-O-Va AL-C or No 814 and lamp P/N 1804. Temp Code T3C. Handheld flashlight Model "Mitylite" Cat No 1900, to be used with two (2) "AAA" size batteries, 1.5V eah per ell by "Eveready" No E92 or Duraell MN2400 or PC2400 and refletor Module P/N 1904. Temp. Code T3C. Handheld flashlight Model "Super Sabrelite" Cat No 2000, to be used with three (3) "C" size batteries, 1.5V eah per ell by "Eveready" E93 or "Eveready" No CH35 or Duraell MN1400 or PC1400 or Ray-O-Va AL- C or No 814 with lamp module P/N 2004. Temp Code T3C. Handheld or lip-on flashlight Model "VersaBrite" Cat No 2250 to be used with two(2), "AA" size batteries, 1.5V eah by Eveready No E91 or Duraell MN1500 or PC1500 or Ray-O-Va No 815 and lamp module Cat No 2204. Temp Code T3C. Ambient: 35 C to +40 C. Handheld flashlight Model "Mitylite Magnum" Cat No 2300 to be used with two (2) "AA" size batteries, 1.5V eah by "Eveready" No E91 or Duraell MN1500 or PC1500 or Ray-O-Va No 815 with lamp module CAT # 2304; Temp. Code T3C. Handheld flashlight Model "StealthLite" Cat No 2400, to be used with four (4) "AA" size batteries, 1.5V eah by "Eveready" No E91 or Duraell MN1500 or PC1500 or Ray-O-Va No 815 with lamp module Cat No 2404; Temp. Code T3C. Handheld flashlight Model "Stealthlite Rehargeable" Cat No 2450 to be used with four (4) "AA" size batteries, 1.5V eah by Eveready No E91 or Duraell MN1500 or PC1500 or Ray-O-Va No 815 or rehargeable battery pak Cat No 2469; used with lamps module CAT # 2454; Temp Code T3C. Handheld flashlight Model Heads-Up Cat No 2600, for use with four (4) size AA, 1.5V eah, battery ells by Eveready No E91 or Duraell MN1500 or PC1500 or Ray-O-Va No 815 and light bulb Cat No 2604 or 2605; Temp Code T3C Handheld lantern Model "King Pelian Lite" Cat No 4000, to be used with eight (8) size "D" Eveready E95 or Duraell MN1300 or PC1300 or Ray-O-Va AL-D or No 813 battery ells, 1.5V eah, with lamp Cat No 4003. Temp Code T3C. Ambient: 0 C to +40 C.

Certifiate: 1640694 Master Contrat: 154507 Projet: 2657098 Date Issued: January 3, 2014 APPLICABLE REQUIREMENTS CAN/CSA C22.2 No. 0-M91 - General Requirements - Canadian Eletrial Code, Part II CAN/CSA C22.2 No. 213-M1987 - Non-Inendive Eletrial Equipment for Use in Class I, Division 2 Hazardous Loations CEC Part I - Se 18.252 - As a guide. CAN/CSA C22.2 No. 25-1966 - Enlosures for Use in Class II, Groups E, F and G Hazardous Loations CAN/CSA-C22.2 No. 157-92 - Intrinsially Safe and Non-Inendive Equipment for Use in Hazardous Loations MARKINGS - Company name; - Model number; - Serial number; - Hazardous loations designation; - CSA Monogram; - Temperature Code Rating; - Ambient temperature range. - Battery Type; - Lamp Type or Lamp Module Cat. No. - Battery pak Cat. No. - The following warnings shall appear in Operating Instrutions: "WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR USE IN HAZARDOUS LOCATIONS "WARNING - EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED AND/OR CHARGED IN NON-HAZARDOUS LOCATIONS"

4D4AO.AX (3613, 36 11) SUPER PELILITE, MODEL 1800 MITYLITE MAGNUM, MODEL 2300 VERSABRITE I, MODEL 2250 VERSABRITE II, MODEL 2270 SEALED HANDHELD FLASHLIGHTS for HAZARDOUS (CLASSIFIED) LOCATIONS from PELICAN PRODUCTS I 1.1 Pelian Produts requested Approval of the apparatus listed in Setion 1.2 to be in ompliane with the appliable requirements of the following standards: Title No. Issue Date Eletrial Equipment for Use in Hazardous FMRC 36 00 Marh 19 89 Loations, General Eletri Flashlights and Lanterns for Use in Class I, FMRC 36 13 June 1996 Div. 2, Class I, Zone 2 Hazardous (Classified) Loations Eletrial Equipment for Use in Class I, Div. 2, FMRC 36 11 April 19 86 Class II, Div. 2 and Class III, Divisions 1 and 2 Hazardous Loations 1.2 The fashlights listed in Setions 1.3 and 1.4 have been previously approved by FMRC. They were submitted for re-examination to determine ignition apabilities at elevated pressures.

FACTORY MUTUAL RESEARCH CORPORATION Job Identifiation 4D4AO.AX 1.3 The following apparatus was evaluated as Noninendive for Class I, Division 2, Groups A,B,C and D hazardous (lassified) loations and will appear in the Approval Guide as follows: NI/1/2/ABCD VersaBrite I Handheld Flashlight. Model 2250* *When used with 2"AA" Eveready Energizer E9 1, Duraell MN1500 or Ray-0-Va AL-AA or 815 Batteries and Lamp Module Cat. No. 2204, PIN 19 03-350-000. VersaBrite II Handheld Flashlight. Model 2270* *When used with 2 "AA" Eveready Energizer E9 1, Duraell MN1500 or Ray-0-Va AL-AA or 815 Batteries and Lamp Module Cat. No. 2274, PIN 2273-351-000. 1.4 The following apparatus was evaluated as Noninendive for Class I, Division 2, Groups A,B, C and D; Suitable for Class II, Division 2, Groups F and G and Suitable for Class III, Division 2 hazardous (lassified) loations and will appear in the Approval Guide as follows: Nl/1/2/ S/11/2/FG; S/111/2 MityLite Magnum Sealed Handheld Flashlight. Model 2300* *When used with 2 "AA" Eveready Energizer E9 1, Duraell MN1500 or Ray-0-Va AL-AA or 815 Batteries and Lamp Module Cat. No. 2304, PIN 2303-351-000. Super PeliLite Sealed Handheld Flashlight. Model 1800* *When used with 2 "C" Eveready Energizer E9 3, Duraell MN1400 or Ray-0-Va AL-C or 813 Batteries and Lamp Module Cat. No. 1804, PIN 1803-350-000. II 2.1 General - The flashlights listed in Setions 1.3 and 1.4 are handheld portable battery powered flashlights. The MityLite Magnum Model 2300 and Super PeliLite Model 1800 are sealed for underwater usage and ontain a vent valve for pressure relief. The Models 2250, 2270 and 2300 ontain two "AA" batteries and the Model 1800 ontains two "C" batteries. The batteries in eah flashlight are series onneted. All models are ativated by the rotation of the bezel. 2.2 Lamp Assemblies - All models utilize lamp assemblies manufatured by Carley Lamp and speified as follows: Pelian Produts Model 2250 2270 2300 1800 787 111 4 1080 841 PIN Cat. No. PIN 2204 19 03-350-000 2274 2273-351-000 2304 2303-351-000 1804 1803-350-000

FACTORY MUTUAL RESEARCH CORPORATION Job Identifiation 4D4AO.AX III AND Representative samples of the apparatus listed in Setions 1.3 and 1.4 were examined and tested by Fatory Mutual Researh Corporation (FMRC) to determine their aeptability for use in the speified hazardous loations. The examination inluded enlosure pressure testing, ignition testing, temperature evaluation and dust-exlusion testing, as well as a review of the manufaturer's doumentation and the unit's physial onstrution. All were satisfatory and are summarized in the following setions. All data is on file at FMRC along with other douments and orrespondene appliable to this program. 3.1 N oninendive Examination - N oninendive equipment aeptability is based on the inability of the apparatus to release suffiient eletrial or thermal energy under normal operating onditions to ause ignition of speifi hazardous atmospheres. 3.1.1 Enlosure Pressure Test - Pressure testing was onduted on a series of six samples to determine the maximum internal pressure prior to venting. The test was onduted on a fully assembled model void of batteries. This test is required only for sealed flashlights. The results are as follows: Maximum Pressure MityLite Magnum, 2300 Super PeliLite, 1800 3.4 psi 2.2 psi The above models utilize a threaded over to atuate the lamp. A seond set of tests was onduted to verify that there is no ejetion of the over or parts of the devie. With the batteries in plae, the threaded over was unsrewed two turns past the extinguishing point of the lamp. Pressure was applied until venting ourred. There was no rupturing of the lens, over, or any other parts. 3.1.2 Make/Break Evaluation - Spark ignition testing was onduted using a 21 % hydrogen-in-air mixture at 1.1 times the maximum reorded venting pressure. A series of six tests on a battery set was onduted in its intended onfiguration for eah battery type and manufaturer. A fresh set of batteries was used for eah test. Results are as follows: 3.1.2.1 Models 2300, 2250 and 2270 - The test iruit onsisted of two fresh "AA" ells with no lamp resistane in the iruit. The gas mixture was pressurized to 3.74 psi A series of six tests were onduted using Duraell MNl 500 ells, Eveready Energizer E91 ells and Ray-0-Va AL-AA ells. Results were satisfatory in that there was no ignition of the test gas. 3.1.2.2 Model 1800 - The test iruit onsisted of two fresh "C" ells with no lamp resistane in the iruit. The gas mixture was pressurized to 2.40 psi. A series of six tests were onduted using Duraell MN1400 ells, Eveready Energizer E93 ells and Ray-0-Va AL-C ells. Results were satisfatory in that there was no ignition of the test gas.

FACTORY MUTUAL RESEARCH CORPORATION Job Identifiation 4D4AO.AX 3.1.3 Drop Test - Fully assembled representative samples of eah model were dropped six times onto a onrete floor from a height of 3 ft. (0.9m). The diretion of the unit was varied so as to impat the floor on all sides. The results are satisfatory in that there was no separation or ejetion of the batteries or any damage whih would affet safety in the Division 2 hazardous loation. 3.1.4 Temperature Evaluation 3.1.4.l VersaBrite II Model 2270 and MityLite Magnum Model 2300 - Temperature evaluation for VersaBrite II Model 2270 and MityLite Magnum Model 2300 are based on testing onduted under FMRC J.I. 2Z3A8.AX. The maximum temperature was measured on the lamp and referened to a 40 C ambient. VersaBrite II Model 2270 MityLite Magnum Model 2300 Temperature Code= T3A (180 C) Temperature Code= T3A (180 C) 3.1.4.2 VersaBrite I Model 2250 and Super PeliLite Model 1800 - Temperature evaluation was based on testing for T4 Classifiation aording to omponent size and ambient temperature. Testing was onduted by plaing a lamp assembly in a mixture of diethyl-ether and powering the lamp with a fresh set of batteries. Results were satisfatory in that there was no ignition of the test gas. VersaBrite I Model 2250 Super PeliLite Model 1800 Temperature Code= T4 (135 C) Temperature Code= T4 (135 C) 3.2 Class II, il Evaluation - The enlosures of the MityLite Magnum, Model 2300, and Super PeliLite, Model 1800, were evaluated for dust-exlusion and temperature. Testing as follows: 3.2.1 Impat Test - A fully assembled representative sample of eah model was subjeted to an impat of 2.7 Joule. The impat was obtained by dropping a 4 lb (1.8 kg) weight from a height of 6 inhes (150 mm) onto the lens, vent and side of vent. Results were satisfatory in that no damage ourred to the sample that would impair the enlosures ability to pass the subsequent dust exlusion test. 3.2.2 Normal and Cold Drop Test - Fully assembled samples of eah model were subjeted to a drop test at room temperature as desribed in Setion 3.1.3. Additional samples were subjeted to a drop test at a temperature of -25 C. The lens aps were loosened two turns past the extinguishing point of the lamps and samples were dropped 3 times at a different angle from a height of 3 feet onto a onrete floor. Results were satisfatory in that no damage ourred to the sample that would impair the enlosures ability to pass the subsequent dust exlusion test. 3.2.3 Dust-Exlusion Test - A Model 2300 and Model 1800 fully assembled enlosure was suspended in a irulating dust atmosphere of 200 mesh tal while onneted to a vauum pump adjusted to draw a vauum of 20 mbar on eah sample. The lens aps on both samples were loosened two turns past the extinguishing point of the lamps. The test was ontinued for eight hours at an average air extration rate of 18.1 volumes per hour for the Model 2300 and 15.2 volumes per hour for the Model 1800. At the onlusion of the test, exess dust was removed from the sample exteriors and the samples opened. Results were satisfatory as the enlosures exluded the entry of dust.

FACTORY MUTUAL RESEARCH CORPORATION Job Identifiation 4D4AO.AX 3.2.4 Temperature Testing - Measurements were taken on the lens under a one inh layer of dust. The maximum reorded temperatures, when adjusted to an ambient temperature of 40 C, are 84.3 C for the Model 2300 and 80.5 C for the Model 1800. There was no harring of the dust as a result of this test. No additional temperature ode is required. 3.2.5 Mold Stress - One omplete sample of Model 2300 and Model 1800 (void of batteries) was plaed in a full irulating air oven at a temperature of 94.l C for 7 hours. After allowing the samples to ool to room temperature, it was determined that there was no damage to any parts, external or internal. IV Marking is molded onto the body of the flashlight and meets standard requirements as illustrated by the attahed labels. V REMARKS 5.1 Only the speifi batteries and lamps tested shall be used with this apparatus. The batteries are to be installed aording to the manufaturer's instrutions. 5.2 Only fresh batteries should be used when ells are replaed. 5.3 Batteries and lamps must not be replaed in a hazardous area. the system. 5.4 Tampering or replaement with nonfatory omponents may adversely affet the safe use of VI FACILITIES AND AUDIT The manufaturing site in Torrane, CA is examined on a periodi basis with regard to failities and quality ontrol proedures. Results are satisfatory in that the level of performane assures ontinued produt quality as originally Approved herein. VII MANUFACTURER'S RESPONSIBILITIES 7.1 The doumentation listed in Setion VIII is appliable to this Approval and is on file at Fatory Mutual Researh Corporation. No hanges of any nature shall be made unless notie of the proposed hange has been given and written authorization obtained from FMRC. The Approved Produt - Revision Report, FMRC Form 797 shall be forwarded to Fatory Mutual Researh Corporation as notie of proposed hanges.

FACTORY MUTUAL RESEARCH CORPORATION Job Identifiation 4D4AO.AX VIII The following doumentation is appliable to this Approval and is on file at Fatory Mutual Researh Corporation. 1903-300-000 A Gas Pellet 1800-001 1800-000 q' 1801-941-ooo 2001-946 -000 1804-401-000 S22 1203-2 1803-920-100 1803-350-000 1803-321-000 1803-331-000 2103-300-110 1803-341-000 1803-945-110 2003-347-000 2003-346 -000 2003-322-000 B F e-y._ B B PR A E A B B A Label Assembly Body Plug Valve Foam Pad Lanyard Slide & End End Cap Lens Cat. # 1804 Lamp Module 0-Ring Battery Retainer Lanyard Spring, Battery Contat Shroud Spring Purge Valve Dis Relief Valve 0-Ring Relief Valve - Model 2300 2300-001 B 2300-010-110 I 2303-351-000 E 3113-301-000 2303-321-000 B 2003-346 -000 2003-322-000 A 2303-342-000 B 2303-343-000 PR 2303-925-000 B 2303-331-000 E 2003-347-000 B 2303-920-100 B 2301-920-000 H Label Assembly Lamp Module, Cat# 2304 Plug Valve 0-Ring Dis Relief Valve 0-Ring Relief Valve Contat Pad Washer Shroud Retainer Spring Purge Valve Lens Body

FACTORY MUTUAL RESEARCH CORPORATION Job Identifiation 4D4AO.AX Doument No. Revision I II - 2250 & 2270 2200-001 2250-000-000 2270-010 2203-342-000 2273-342-000 2203-343-000 2403-344-000 2200-010 2200-020 1971-925-110 2271-925-110 1903-920-100 2303-920-1 00 2203-341-000 1903-341-000 2273-341-000 2501-923 2203-350-000 2273-351-000 1903-321-000 2303-321-000 2501-924 2003-345-0000 E D PR A D G A B B B D D PR A A PR Label Cut-Away Drawing - Model 2250 Cut-Away Drawing - Model 2270 Ring - Model 2250 Ring - Model 2270 Eyelet, Hinge Jumper Contat Case Cap Shroud - Model 2250 Shroud - Model 2270 Lens - Model 2250 Lens - Model 2270 Spring, Battery Contat Spring - Model 2250 Spring - Model 2270 Goose-Nek Lamp Module, Cat # 2204 - Model 2250 Lamp Module, Cat# 2270 - Model 2270 0-Ring - Model 2250 0-Ring - Model 2270 Cover Eyelet, Contat - Model 2270 IX The apparatus desribed in Setion 1.2 meets Fatory Mutual Researh Corporation requirements. Approval is effetive when the Approval Agreement is signed and reeived by FMRC. EXAMINATION AND TESTS BY: Cheryl A. Gagliardi, John J. Woolley, Curt D. Mae ORIGINAL TEST DATA: Projet Data Reord 4D4AO.AX ATTACHMENTS: Model 1800 Label Drawing - Dwg. 1800-001, Rev. B Model 2300 Label Drawing - Dwg. 2300-001, Rev. B Models 2250 & 2270 Label Drawing - Dwg. 2200-001, Rev. C WRITTEN BY: REVIEWED BY: