Series RoS ompliant onnectors onforming to European Safety Standards s of January 1995 all industrial machinery, including machine tools, which are exported to Europe must conform with European safety standards. The series connectors, which offer full compatibiliy with /MS connectors in factory automation applications, were developed to comply with this demand. FETURE TUV Rheinland onformity with European Safety Standards series connectors fully conform with the following European safety standards : EN60204-1 (electric machinery parts) and IN VE 0627 (connectors). They have been approved by TUV Rheinland. Sequence Structure with Protective ircuitry (First-make, Last-break contact design) onnectors are provided with a premating and grounding contact, consisting of a shell having conductivity with the shell to serve as protective circuitry. When making connections, the contact of the connector is connected first before other contacts, and detached last. onformity with MIL--5015 connectors fully comply with MIL--5015 standards and can be mated with conventional MS connectors. Water/Oil/ustproof Structure : lass IP67 Protection Once connected, full protection is provided against ingression of water droplets, cutting fluid, dust particles, etc. Use of a synthetic rubber insert ensures protection against water and dust even in the unconnected state in the case of the receptacle with male contacts. Plug onnector ccessories vailable accessories include waterproof straight-backshells, waterproof angle-backshells and waterproof cable clamps (with rubber bushing). Plug connectors are also available for conduit applications. Solder Wire Like /MS connectors, connectors have solder buckets. Note : connectors offer full compatiblity with MS series connectors. MTERIL/FINIS ontact Pin front insert Pin rear insert Socket insert Shell oupling ring Retaining ring Ground tab Gasket opper alloy/silver plating Synthetic rubber/lack Synthetic resin/lack Synthetic resin/lack luminum alloy/zinc plating, Trivalent hromate finish (lack) luminum alloy/zinc plating, Trivalent hromate finish (lack) opper alloy/nickel plating opper alloy/silver plating Synthetic rubber/lack 1
Series Wire Size ontact Size Wire Size #16 WG#22-#16 #12 WG#14-#12 #8 WG#10-#8 #4 WG#6-#4 Specification urrent rating ontact size #16 #2 #8 #4 Max. value per contact 13 23 46 80 ielectric withstanding voltage (rms), 1minute 1000V, 2000V, 2800V or 3000V Insulation resistance 5000MΩ Min. at 500V Operating temperature -55 to +125 onnection Series Plug Nonwateproof able lamps Waterproof Straight ackshell Staight Plug Waterproof Receptacle onnectors Nonwateproof able lamps Waterproof able lamps Waterproof ngle ackshell Right ngie Plug MS Series Flexible onduit Waterproof able lamps Straight Plug Wall Mounting Receptacle Straight Piug able onnecting Receptacle Flexible onduit Flexible onduit Jacketed able onduit Right ngle Plug ox Mounting Receptacle 2
Series List of Series Insert No. Receptacle Plug Note 10SL-3-210SL-3P- 18-10 -218-10P- 18-12 -218-12P- 20-4 -220-4P- 20-15 -220-15P- 22-22 -222-22P- 22-23 -222-23P- 24-10 () -224-10P- 24-10 (G) -224-10PG- 32-17 -232-17P- Waterproof able lamp or onduit -610SL-3S- Without ack Shell Type For onduit -610SL-3S--SS Straight ack Shell Type E3057-4-1- -810SL-3S--S ngle ack Shell Type -618-10S- Without ack Shell Type For onduit -618-10S--SS Straight ack Shell Type E3057-10- - -818-10S--S ngle ack Shell Type -618-12S- Without ack Shell Type For onduit -618-12S--SS Straight ack Shell Type E3057-10- - -818-12S--S ngle ack Shell Type -620-4S- Without ack Shell Type For onduit -620-4S--SS Straight ack Shell Type E3057-12- - -820-4S--S ngle ack Shell Type -620-15S- Without ack Shell Type For onduit -620-15S--SS Straight ack Shell Type E3057-12- - -820-15S--S ngle ack Shell Type -622-22S- Without ack Shell Type For onduit -622-22S--SS Straight ack Shell Type E3057-12- - -822-22S--S ngle ack Shell Type -622-23S- Without ack Shell Type For onduit -622-23S--SS Straight ack Shell Type E3057-12- - -822-23S--S ngle ack Shell Type -624-10S- Without ack Shell Type For onduit -624-10S--SS Straight ack Shell Type E3057-16- - -824-10S--S ngle ack Shell Type -624-10SG- Without ack Shell Type For onduit -624-10SG--SS Straight ack Shell Type E3057-16- - -824-10SG--S ngle ack Shell Type -632-17S- Without ack Shell Type For onduit -632-17S--SS Straight ack Shell Type E3057-20- - -832-17S--S ngle ack Shell Type 3
Series Insert rrangements Insert No. 10SL-3 18-10 18-12 20-4 20-15 rrangements E F E F G ontact Size #16 #12 #16 #12 #12 No. of ontacts 3 4 6 4 7 Premating ontact Position Voltage Rating Withstanding Voltage 200V (rms) 250V (rms) 250V (rms) 250V (rms) 250V (rms) 2000V (rms) 3000V (rms) 2000V (rms) 2800V (rms) 2000V (rms) urrent apacity 13 (29.2) 23 (62.5) 13 (43.6) 23 (62.5) 23 (83.7) Insert No. 22-22 22-23 24-10 () 24-10 (G) 32-17 rrangements F E G F E G F E G ontact Size #8 #12 #8 #8 #4 No. of ontacts 4 8 7 7 4 Premating ontact Position G Voltage Rating Withstanding Voltage urrent apacity 250V (rms) 250V (rms) 250V (rms) 250V (rms) 250V (rms) 3000V (rms) 2000V (rms) 2000V (rms) 2000V (rms) 2800V (rms) 46 (125.1) 23 (90.1) 46 (167.4) 46 (167.4) 80 (217.6) Note 1) The above figures show the views from solder cup side of E02-6 plug connectors (socket insert). 2) urrent capacities show the maximum permitted current values per contact. 4
Series lternate Insert Positions Z W Y X Front View of Socket Insert Insert No. ontact size/ Number W X Y Z 10SL-3 #16/3 - - - - 18-10 #12/4-120 240-18-12 #16/6 80 - - 280 20-4 #12/4 45 110 250-20-15 #12/7 80 - - 280 22-22 #8/4-110 250-22-23 #12/8 35 - - - 24-10 #8/7 80 - - 280 32-17 #4/4 45 110 250-5
Series Receptacle -218-10PYS- SELL STYLE 2 : ox Mounting Receptacle SELL OLOR : lack SELL SIZE 10SL, 18, 20, 22, 24, 32 INSERT RRNGEMENT See page 4 ONTT STYLE P : Pin FLNGE GSKET Omit : Less Gasket S : With Gasket LTERNTE INSERT POSITION Omit : Standard position W,X,Y,Z : lternate position PREMTING ONTT POSITION Reter to insert arrangements F ±1 G ± 0.5 dia L +0.25-0.12 dia min J ± 0.15 +0.97-0.5 ± 0.35 K ± 0.15 E ±1 Thread P/N E F G J K L -210SL-3P- 5 / 8-24UNEF-2 14.27 2.15 23.50 12.4 16 9.53 18.26 25.4-218-10P- 1 1 14.2 / 8-18UNEF-2 30.50 27 26.97 34.9-218-12P- 13.3-220-4P- 3.05 1 1 / 4-18UNEF-2 19.05 30.60 14.2 32 29.36 38.1-220-15P- 2.75-222-22P- 15.88 1 3 17.2 / 8-18UNEF-2 31.50 33 31.75 41.3-222-23P- 14.3-224-10P- -224-10PG- 1 1 / 2-18UNEF-2 20.63 33.85 15.6 36 34.92 44.4 3.74-232-17P- 2-18UNS-2 22.23 3.35 38.15 20.2 48 44.45 57.2 4.40 6
Series Plug -618-10SY--SS SELL STYLE 6:Straight plug SELL SIZE 10SL, 18, 20, 22, 24, 32 ONNETOR STYLE Omit:Without ack Shell (For onduit) SS:Straight Plug (With Straight ack Shell) S:Right ngle Plug (With Right ngle ack Shell) INSERT RRNGEMENT See page 4 SELL OLOR : lack ONTT STYLE S:Socket LTERNTE INSERT POSITION Omit:Standard position W,X,Y,Z:ltemate Position PREMTING ONTT POSITION Refer to insert arrangements Plug -6 - S - Gasket J G +0.05-0.25 dia 0-0.38 dia E ±0.5 ±1 ±1 P/N oupling Threads Pear Threads E G J -610SL-3S- 5 / 8-24UNEF-2 22.22 23.3 9 / 16-24UNEF-2 7.50 12.5 5.6 13.2-618-10S- 1 1 6.4 / 8-18UNEF-2 34.13 33.7 1-20UNEF-2 11.74 23.5-618-12S- 5.6-620-4S- 1 1 / 4-18UNEF-2 37.28 34.1 1 1 6.0 / 8-18UNEF-2 12.16 26.8-620-15S- 6.0-622-22S- 1 3 / 8-18UNEF-2 40.48 34.1 1 1 9.3 / 4-18UNEF-2 14.65 29.9-622-23S- 6.1-624-10S- 1 1 / 2-18UNEF-2 43.63 36.6 1 3 6.8 / 8-18UNEF-2 13.42 32.9-624-10SG- 6.8-632-17S- 2-18UNS-2 56.33 37.0 1 7 / 8-16UN-2 13.14 45.3 9.2 19.0 19.4 7
Series Straight Plug -6 - S --SS W max 7.85 min ±0.8 dia 0-0.38 dia P/N oupling Threads Rear Threads W -610SL-3S--SS 5 / 8-24UNEF-2 22.22 18.6 40 5 / 8-24UNEF-2-618-10S--SS -618-12S--SS 1 1 / 8-18UNEF-2 34.13 32.1 57 1-20UNEF-2-620-4S--SS -620-15S--SS 1 1 / 4-18UNEF-2 37.28 35.2-622-22S--SS -622-23S--SS 1 3 / 8-18UNEF-2 40.48 38.3 61 1 3 / 16-18UNEF-2-624-10S--SS -624-10SG--SS 1 1 / 2-18UNEF-2 43.63 42.0 68 1 7 / 16-18UNEF-2-632-17S--SS 2-18UNS-2 56.33 54.2 79 1 3 / 4-18UNS-2 8
Series Right ngle Plug -8 - S --S max U ± 0.7 R ± 0.7 Y min 0-0.38 dia W P/N oupling Threads Rear Threads W R U Y -810SL-3S--S 5 / 8-24UNEF-2 22.22 47.8 5 / 8-24UNEF-2 7.9 21.0-818-10S--S -818-12S--S 1 1 / 8-18UNEF-2 34.13 69.5 1-20UNEF-2 13.2 30.2-820-4S--S 1 1 / 4-18UNEF-2 37.28 15.0-820-15S--S 75.5 1 3 / 16-18UNEF-2-822-22S--S 1 3 / 8-18UNEF-2 40.48 16.3-822-23S--S 33.3-824-10S--S -824-10SG--S 1 1 / 2-18UNEF-2 43.63 86.3 1 7 / 16-18UNEF-2 18.2 36.5-832-17S--S 2-18UNS-2 56.33 93.5 1 3 / 4-18UNS-2 24.6 44.5 8.5 7.5 9
Series ccessories Waterproof Straight ack Shell - S-S- Material/Finish luminum alloy/lack chromate finish - S-S- is a waterproof backshell to hold a length of cable when no conduit is used. L Set SREW (SUS/ONE SPOT) W V dia O-ring dia 7.85min Shell Size P/N L 10SL -10SLS-S- 20.0 18.6 6.5 6.6 17.9 Threads V 9 / 16-24UNEF-2 Threads W 5 / 8-24UNEF-2 18-18S-S- 31.0 32.1 10.5 16.3 26.7 1-20UNEF-2 1-20UNEF-2 20-20S-S- 35.0 35.2 10.9 17.8 31.6 1 1 / 8-18UNEF-2 1 3 / 16-18UNEF-2 22-22S-S- 35.0 38.3 10.9 17.8 32.4 1 1 / 4-18UNEF-2 1 3 / 16-18UNEF-2 24-24S-S- 40.5 42.0 12.2 21.0 36.6 1 3 / 8-18UNEF-2 1 7 / 16-18UNEF-2 32-32S-S- 46.0 54.2 11.7 25.8 47.3 1 7 / 8-16UN-2 1 3 / 4-18UNS-2 10
Series Waterproof ngle ack Shell E- -S- Material/Finish luminum alloy/lack chromate finish E- -S- is a waterproof backshell to hold a length of cable at right angle when no conduit is used. L1 max L2 max U R Y min V O-ring dia W Shell Size P/N L1 L2 R U Threads V Threads W Y 5 / 8-24UNEF-2 7.5 10SL E-10SL-S- 30.6 22.5 21.7 7.9 21.0 9 / 16-24UNEF-2 18 E-18-S- 44.6 34.0 32.4 13.2 30.2 1-20UNEF-2 1-20UNEF-2 7.5 20 E-20-S- 50.5 39.6 36.0 15.0 33.3 1 1 / 8-18UNEF-2 1 3 / 16-18UNEF-2 7.5 22 E-22-S- 50.5 39.6 38.6 16.3 33.3 1 1 / 4-18UNEF-2 1 3 / 16-18UNEF-2 7.5 24 E-24-S- 60.1 47.9 42.4 18.2 36.5 1 3 / 8-18UNEF-2 1 7 / 16-18UNEF-2 7.5 32 E-32-S- 69.1 55.1 55.3 24.6 44.5 1 7 / 8-16UN-2 1 3 / 4-18UNS-2 8.5 11
Series Waterproof able lamps E3057- - - Material/Finish luminium alloy/zinc Plating. lack chromate finish E3057- - - is a waterproof cable clamp for use with a plug. The cable clamp body is the /MS3057- K that has a waterproof rubber bushing. Therefore, be sure to use a jacketed cable meeting one of the applicable cable size ranges as shown. The cable clamp should be used together with a waterproof backshell. V 1.5 F dia G E dia P/N Shell Size F G Threads V ushing P/N able Outer iameter E3057-4-1-10SL 20.6 20.6 5.6 22.2 5 / 8-24UNEF-2 E3420-4-1 3.6~ 5.6 E3057-10-1-14.1 E3420-10-1 10.5~14.1 E3057-10-2-18 23.8 30.1 11.0 31.7 1-20UNEF-2 E3420-10-2 8.5~11.0 E3057-10-3-8.7 E3420-10-3 5.5~ 8.7 E3057-12-1-16.0 E3420-12-1 12.5~16.0 E3057-12-2-20, 22 23.8 35.0 13.0 37.3 1 3 / 16-18UNEF-2 E3420-12-2 9.5~13.0 E3057-12-3-10.0 E3420-12-3 6.8~10.0 E3057-16-1-19.1 24 26.2 42.1 42.9 1 7 E3420-16-1 15.0~19.1 / 16-18UNEF-2 E3057-16-2-15.5 E3420-16-2 13.0~15.5 E3057-20-1-23.8 E3420-20-1 22.0~23.8 E3057-20-2-32 27.8 51.6 26.6 51.6 1 3 / 4-18UNEF-2 E3420-20-2 24.0~26.6 E3057-20-3-22.5 E3420-20-3 22.0~22.5 12
Series ushing E3420- - Material/Finish Synthetic rubber (lack) E3420- - is the bushing used on cable clamp part number E3057- - - dia dia dia P/N pplicable Washer E3420-4-1 5.6 7.5 11.8 38.4 MS3057-4W E3420-10-1 14.1 E3420-10-2 11.6 15.5 21.6 38.5 MS3057-10W E3420-10-3 8.7 E3420-12-1 16.0 E3420-12-2 13.0 18.6 25.1 39.3 MS3057-12W E3420-12-3 10.0 E3420-16-1 19.1 E3420-16-2 15.5 23.4 30.5 40.0 MS3057-16W E3420-20-1 23.8 31.4 38.2 41.0 MS3057-20W NOTE : Please place an order for a washer separately from a bushing. 13
Series ap and hain ssembly (Not Waterproof) Material/Finish ap luminum alloy/lack chromate finish hain Stainless steel The cap and chain assembly protects the connector joint by preventing the intrusion of dust or other foreign substances that may impair the electrical connection. The cap for the receptacle (/MS25043) comes with a drip-resistant gasket. /MS25042- (For Plug) P/N Shell Size Threads E /MS25042-10 10SL 5 / 8-24UNEF 15.9 15.9 3.9 101 /MS35042-18 18 1 1 / 8-18UNEF 20.7 28.6 3.9 114 /MS25042-20 20 1 1 / 4-18UNEF 20.7 31.8 4.7 127 /MS25042-22 22 1 3 / 8-18UNEF 20.7 34.9 4.7 127 E /MS25042-24 24 1 1 / 2-18UNEF 20.7 38.1 4.7 139 /MS25042-32 32 2-18UNS 20.7 50.8 5.5 190 /MS25043- (For Receptacle) P/N Shell Size Threads E /MS25043-10 10SL 5 / 8-24UNEF 11.1 19.1 3.3 101 /MS35043-18 18 1 1 / 8-18UNEF 11.1 31.8 3.5 114 /MS25043-20 20 1 1 / 4-18UNEF 11.1 34.9 3.5 127 /MS25043-22 22 1 3 / 8-18UNEF 11.1 38.1 3.5 127 /MS25043-24 24 1 1 / 2-18UNEF 11.1 42.9 4.3 139 E /MS25043-32 32 2-18UNEF 12.7 55.6 4.7 190 14