INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-100B 2008 ELEMENT (SC) AII 36532 Issue Date MAY 2007 PARTS LIST Relay bracket Right fog light Relay Left fog light Fuse label Right fog light bracket 17 Wire ties 2 Wire ties with clip Left fog light bracket 8 Self-tapping screws Right sub-bracket 3 Washer-bolts Left sub-bracket Flange nut Switch Switch harness 2 Grommets Fog light harness 2 Self-tapping washer-screws Clip 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36532 (0705) 08V31-SCV-1000-9A 1 of 12
TOOL AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 8 mm and 10 mm sockets File Utility knife Clip remover Masking tape Eye protection (face shield, safety goggle, etc.) Installing the Fog Light 3. Open the hood and remove the radiator cover (five clips). CLIPS Illustration of the Fog Light Installed on the Vehicle FUSE CASE (20A) FOG LIGHT INSTALLATION RELAY 5003010K RADIATOR COVER 2328091K 4. With the help of an assistant, remove the front bumper (seven clips at the top, four clips and four stepped bolts at the bottom, one self-tapping washer-screw on each side and one self-tapping screw on each side). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 7 CLIPS NOTE: These installation instructions show the left fog light being installed. The same procedure applies to installing the right fog light. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. FRONT BUMPER 4 CLIPS 2 SELF- TAPPING SCREWS 4 STEPPED BOLTS 2 SELF- TAPPING WASHER- SCREWS 5912021T 2 of 12 AII 36532 (0705) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
5. Apply masking tape to the front bumper in the area shown. FRONT BUMPER (LEFT SIDE) 7. Install the grommet to the left sub-bracket. Install the left sub-bracket with one washer-bolt to the left fog light. The left sub-bracket is stamped with the identification mark L, and the right subbracket is stamped R. LEFT MASKING TAPE 6224060K 6. Inside the front bumper, locate the slit on the fog light housing on the left side. Using a utility knife, cut out the marked area from the front bumper along the groove on the back. Remove all burrs from the edges of the cutout. WASHER- BOLT LEFT SUB- GROMMET IDENTIFICATION MARK 5929020K FRONT BUMPER 8. Inside the front bumper, slide the left fog light bracket into the cutout you made, and secure it with four self-tapping screws. HOUSING SLIT LEFT HOUSING GROOVE (Cut out.) FRONT BUMPER GROOVE (Cut out.) GROOVE SECTIONAL VIEW 5928011K 4 SELF-TAPPING SCREWS 5929010K 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36532 (0705) 3 of 12
9. Insert the left fog light from the fog light opening at the front of the front bumper to the left fog light bracket and install it with one self-tapping washer-screw to the left fog light bracket. Routing the Fog Light Harness 11. Starting under the left headlight, route the fog light harness 1-pin connector and ground terminal through the hole in the front bulkhead. SELF-TAPPING WASHER- SCREW LEFT FOG LIGHT BLUE TAPE 1-PIN 1-PIN GROUND TERMINAL FRONT BUMPER LEFT FOG LIGHT 10. Repeat steps 5 thru 9 to cut the bumper and install the fog light on the right side. 5929030K LEFT FRONT BULKHEAD PANEL 6224051K 12. Locate the 1-pin connector blue-taped to the vehicle harness and remove the blue tape to free the 1-pin connector. Plug the 1-pin connector you just freed to the fog light harness 1-pin connector. 4 of 12 AII 36532 (0705) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
13. Remove the ground bolt that fastens the vehicle ground terminal and secure the fog light harness ground terminal using the ground bolt. 15. Behind the front side frame, route the fog light harness 2-pin connector (short end) down, and out through the clearance between the side frame and front bumper beam. LEFT FRONT SIDE FRAME GROUND BOLT (Reuse.) FRONT BUMPER BEAM GROUND TERMINAL 6224011K 2-PIN (SHORT END) 5003022K 14. Secure the fog light harness 1-pin connector and the fog light harness to the vehicle harness with one wire tie. Do not secure the 1-pin connector to the SRS harness with the wire tie. 16. Route the fog light harness 2-pin connector (long end) from underneath the left headlight to the engine compartment, then along the vehicle harness behind the front bulkhead upper frame. 1-PIN FRONT BULKHEAD UPPER FRAME LEFT HEADLIGHT SRS SENSOR TIE SRS 6516020K 5003031K 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36532 (0705) 5 of 12
17. Continue routing the fog light harness 2-pin connector from underneath the right headlight to the front of the vehicle, then down to the bottom of the front side frame along the outside of the right bulkhead side stay. 19. Secure the fog light harness to the vehicle harness with the eight wire ties in the areas shown. TIES TIES TIES RIGHT HEADLIGHT 6224020K FRONT SIDE FRAME 2-PIN TIES FRONT BUMPER BEAM 5003041K 18. Push each of the two wire ties with clip on the fog light harness into the holes in the bulkhead side stay. Further secure the fog light harness to the vehicle harness with three wire ties in the areas shown. GREEN TAPE TIE 20. Secure the fog light harness. Without Engine Block Heater: Secure the fog light harness to the holes in the bulkhead side stay and the left front bulkhead with the two wire ties with clip. Secure the fog light harness to the vehicle harness with one wire tie. Push each of the two wire ties with clip on the fog light harness into the holes under the front side frame and the bulkhead side stay. TIE WITH CLIP LEFT FRONT BULKHEAD TIE RIGHT BULKHEAD SIDE STAY CLIP LEFT BULKHEAD SIDE STAY TIE WITH CLIP TIE WITH CLIP ON FOG LIGHT 5003052K LEFT FRONT SIDE FRAME TIES WITH CLIP ON 5003062K 6 of 12 AII 36532 (0705) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
With Engine Block Heater: Secure the engine block heater and fog light harnesses to the bulkhead side stay and front bulkhead with the two wire ties on the engine block heater harness and two wire ties with clip. Secure the fog light harness to the vehicle harness with one wire tie. Push each of the two wire ties with clip on the fog light harness into the holes under the front side frame and the bulkhead side stay. TIES ON ENGINE BLOCK HEATER LEFT BULKHEAD SIDE STAY TIE WITH CLIP ENGINE BLOCK HEATER LEFT FRONT TIE BULKHEAD WITH CLIP TIE 23. While holding the front bumper near the front of the vehicle, plug the fog light harness 2-pin connectors into the 2-pin connectors from the fog lights. Reinstall the front bumper. 2-PIN FRONT BUMPER 2-PIN 2-PIN 5003080K Routing the Switch Harness 24. Remove the driver s dashboard lower cover, turn the knobs clockwise, then pull the cover out toward you to release the six retaining tabs. TIES WITH CLIP ON 5003072K 21. Using the utility knife, cut out the marked area from the left front inner fender along the scribed line on the back. Remove any burrs from the edge with a file. (Cut out.) SCRIBED LINE DRIVER S DASHBOARD LOWER COVER LEFT FRONT INNER FENDER KNOBS 2403050K 6 RETAINING TABS 6209011K 22. Cut the right front inner fender the same way. 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36532 (0705) 7 of 12
25. Lower the steering wheel using the tilt lever. Remove the two self-tapping screws and one washer-screw from the lower steering column cover. 27, Slide the relay bracket onto the switch harness relay block STEERING WHEEL (Turn the steering wheel 90 clockwise.) 6 RETAINING TABS RELAY Press. UPPER STEERING COLUMN COVER RELAY BLOCK RELAY TILT LEVER LOWER STEERING COLUMN COVER 5926052K 28. Insert the relay bracket onto the switch harness relay block. 29. Install the relay bracket on the data link connector bracket using one washer-bolt and flange nut. WASHER-BOLT WASHER SCREW SELF TAPPING SCREWS 6516060K DATA LINK 26. Separate the upper steering column cover from the lower steering column cover. Turn the steering wheel 90 clockwise, and press point to release the retaining tab. Press point and then to release the retaining tabs. Once these retaining tabs are released, the retaining tabs on the opposite side will release. RELAY FLANGE NUT 5926061K 8 of 12 AII 36532 (0705) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
30. Locate the 3-pin connector blue-taped to the vehicle harness and remove the blue tape to free the 3-pin connector. Slide the clip onto the 3-pin connector you just freed. 3-PIN 34. Secure the switch harness to the vehicle harness with two wire ties. TIES CLIP 3-PIN BLUE TAPE (Remove.) 6224030K 5926082K 35. Turn the steering wheel 90 counterclockwise. 31. Attach the 20A fuse label to the switch harness fuse case. 1-PIN FUSE BOX FUSE CASE 20A FUSE LABEL 3-PIN 16-PIN COMBINATION 3-PIN Freed in step 30. BOSS SCREWS FUSE BOX 1-PIN PORT 5926072K CLIP DATA LINK HOLE 32. Plug the switch harness 1-pin connector into the fuse box in the location shown. 33. Plug the switch harness 3-pin connector into the 3-pin connector freed in step 30. Push the connector clip into the vehicle hole shown. STEERING (Discard.) 5926090K 36. Unplug the vehicle 16-pin connector from the switch. Remove the two screws from the switch. 37. Pry off the boss by inserting the end of a flat-tip screwdriver between the combination switch and switch, then moving in the direction shown. Remove the switch from the combination switch. Hold the case and not the lever to remove the switch from the combination switch. 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36532 (0705) 9 of 12
38. Install the new switch and plug the vehicle 16-pin connector to the new switch. Make sure you hold the case when installing the switch. 16-PIN SCREWS (Reuse.) USE AND CARE How to Operate Fog Lights Turn the light switch to the position (headlights on low beam). Turn the fog light switch (indicator in the meter come on). NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. If the fog lights don t come on, check the fuse and all the connectors, including the ground cable. Fog Light Aiming Adjustment Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment gear in or out until the correct aiming is obtained. 5926100K 39. Check that all wire harnesses are routed properly and all connectors are plugged in. 40. Reinstall all removed parts. Check that all clips and fasteners are installed securely. 41. Reconnect the negative cable to the battery. 42. Reset the clock, and reset the radio station presets. NOTE: When the battery is disconnected, the driver s window AUTO function is disabled. 43. Start the engine. Push down on the driver s window switch until the window is fully open. 44. Pull up on the driver s window switch fully to close the window completely, then hold the switch for 2 seconds or more. 45. Test the window AUTO function. To raise AIMING ADJUSTMENT GEAR PHILLIPS SCREWDRIVER To lower 5929041K 10 of 12 AII 36532 (0705) 2007 American Honda Motor Co., Inc. - All Rights Reserved.
Replacing the Fog Light Bulb 1. Remove the self-tapping washer-screw from the fog light, pull out the fog light, and disconnect the connector. SELF-TAPPING WASHER-SCREW 3. Install the new bulb into the socket. Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 51W HB4 Halogen Light Bulb P/N 33104-S3V-A010-M1 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with denatured alcohol or a mild detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. 5930011K 2. Turn the bulb 45 counterclockwise and remove it from the socket. BULB 5930030K BULB 5930020K 4. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Make sure to tighten the screws securely. 5. Check the operation of the fog light; adjust the aiming if necessary. 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36532 (0705) 11 of 12
CIRCUIT DIAGRAM HOT AT ALL TIMES WHT/RED HOT WITH HEADLIGHT IN HEAD RED/YEL Front Fog Light Switch Front Fog Light Fuse 20A GRN/YEL WHT Front Fog Light Relay Front Fog Light Indicator RED/WHT BLU/RED Meter Dimmer Switch 1: Low 2: Hi 1 2 Front Fog Lights BLK HEADLIGHT BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE OFF Low Hi BLU BLUE PUR PURPLE GRN GREEN NAT NATURAL OFF - - - - ON - - ON - RED RED PNK PINK WHT WHITE GRY GRAY LT BLU LIGHT BLUE LT GRN LIGHT GREEN 6224040K 12 of 12 AII 36532 (0705) 2007 American Honda Motor Co., Inc. - All Rights Reserved.