F15 Ferra eries Hydraulic Pumps oncentric Innovation in Hydraulics
ERIPION, FEURE N ENEFI oncentric F series gear pumps have an outstanding history in mobile off-highway applications. he F15 is the latest addition. aking the best design components from the F20/F30 series and adding new technology, oncentric has created a product of very high efficiency, yet retains the robust nature of the traditional cast iron bodied gear pump. he gear and shaft are one piece construction for drive and driven gear providing superior resistance to fatigue and allowing the use of large diameter journals for higher load-bearing capacity. Made of high strength heat treated steel, the 14-tooth gears reduce pressure ripple (noise) and improve volumetric efficiency. Large eflon impregnated bushings are installed in precision bored covers for optimum alignment, providing support area capable of handling most indirect drives and fan loads. his design uses one integrated balanced bronze pressure plate for the optimum in wear surface and strength. ith an integrated E seal in the pressure plate, this design reduces clearance, offsets axial loading, and balances itself as pressure increases. he F15 series can be ported in a variety of E, IN, NP, PP, and JI sizes and combinations of side or rear locations. rive shafts in E splined, keyed, and taper are offered. Mounting flanges are E 2-bolt or 2-bolt with either single or double shaft seal configuration. he double seal option is designed for use when the pump pilot extends into a crankcase or transmission. It prevents fluid from one environment entering the other. Pictures on front cover are used with the kind permission of eg: tlet,, Huddig, cania, oro and olvo onstruction Equipment LE OF ONEN, Features and enefits... 2 pecifications and pplication ata... 3 Installation imensions / Model odes F15... 4-5 F19... 6-7 F1515... 8-9 F151515... 10-11 Mounting Flanges...12 rive hafts...13 Performance urves...14 2 oncentric -F15 PMP-U-2011-6
PERFORMNE PEIFIION for F15 Pumps Model heoretical isplacement Per Revolution cc / c.i.r. / 1.159 / 1.403 / 1.5 / 08 / 2.013 / 2.318 / 2.684 / 3.0 ontinuous Rated Pressure bar / psi 276 / 4000 276 / 4000 276 / 4000 276 / 4000 276 / 4000 276 / 4000 2 / 00 207 / 3000 Max Rated peed @ Rated Pressure & 6 Hg acuum Inlet rpm 3600 3600 3600 3600 3600 3600 30 3000 Min Rated peed @ Rated Pressure & 6 Hg acuum Inlet rpm* 600 600 600 600 600 600 600 600 ypical elivery @ Rated peed nd Pressure gpm 16.8 20.3 22.1 24.8.2.6 37.8 36.8 ypical elivery @ Rated peed nd Pressure lpm 63.6 77.0 83.7 93.7 110.4 127.2 14 139.4 ypical Input Power @ Rated peed nd Pressure hp 43.6 52.7 57.3 64.2 75.7 87.1 80.9 7 * Lower speeds are permissable when operating below rated pressure. Rated speed of double pump is governed by pump with lower speed rating. If deliveries of both pumps are combined, rated pressure is governed by pump with lower pressure rating. ypical Input Power @ Rated peed nd Pressure kw 32.48 39.32 42.74 47.87 56.41 64.96 60. 52 Efficiency epending on displacement, speed and pressure, volumetric efficiency is 81-98% and overall efficiency is 71-92% with E 10 oil at 49 (120 F). Inlet conditions Pressure on the inlet should not exceed 1 bar (15 psi). Under continuous operation, inlet vacuum should not exceed 0.17 bar (5 Hg). Operating temperatures Under continuous operation, a maximum of 96 (205 F) is recommended. he maximum temperature for cyclic or intermittent operation is 107 (2 F). Fluids and filtration For applications requiring fire resistant fluids, water glycols, water in-oil emulsions and synthetics can be used at slightly reduced ratings. Fluid should be selected with an operating viscosity similar to the petroleum oil described above. For application assistance, consult your oncentric representative. he system should be filtered to provide an IO code (proposed) cleanliness level of /16. 10 micron filter sized to accommodate full system return line flow, is recommended for most operating environments. evere conditions may require greater efficiency from the filter. oncentric -F15 PMP-U-2011-6 3
F15 [174] 6.9 [41] [9].4 [8] 4X.3 [14] 2X Ø.6 [1] 5.7 [73] 2.9 [147] 5.8 [61] 2.4 [102] Ø 4.0 [17].7 [20].8 FRON / IE IE [118] 4.6 [59] 2.3 [82] [124] Ø 4.9 RER / IO IE 22 30 IR 1.16 1.34 1.40 1.53 1 7 1.83 2.01 2.14 2.32 2.68 3.05 IPLEMEN OE 22 30 F15 3.15 1 3. 7 3. 3. 3. 3. 8 3.54 3.66 3.78 79.9 81.4 82.0 83.1 84.6 85.1 85.7 87.2 88.3 89.8 93.0 96.0 4.63 4.75 4.80 4.88 5.00 5.04 5.09 5.21 5. 5.41 5.66 5.90 117.6 120.7 121.9 124.0 127.0 1.0 1.3 132.3 134.4 137.4 143.8 149.9 ll dimensions shown are for single shaft seal version and for reference only. onsult factory for your specific configuration. 4 oncentric -F15 PMP-U-2011-6
Model ode for F15 Ferra eries ingle Pumps ORERING INFORMION Each option has been assigned an order code -- listed in the tables below -- for placement in the sequence shown at right. 1 (pecial eals) F3 Omit 2 (eries) F15 3 (Mount ype) iton eal tandard F15 Ferra eries ingle Gear Pump ingle haft eal et Mount (ouble haft eal) EXMPLE: (F3)- F15- - 2 - - - - 1- - 12- - 10- L 1 2 3 4 5 6 7 8 9 10 11 12 13 pecial eals Ferra eries Mount ype Front over Inlet Port isplacements Outlet Port Rear over haft eal rive haft Port Locations esign Rotation 4 (Front over) 1 E 2-olt Mount (consult factory) 2 E 2-olt Mount 8 E 2/4-olt ombination Mount (consult factory) 5 (Inlet Port) 1.00, E 4-olt plit Flange 1., E 4-olt plit Flange 1., E 4-olt plit Flange M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring X #24 E (1 7/8-12) O-Ring ontact factory for other requirements. 6 (isplacements) m 3 /In 3 m 3 /In 3 cc/1.16 3 cc/2.32 3 cc/1.40 3 cc/2.68 3 cc/1.53 3 cc/3.05 3 cc/1 3 cc/2.01 3 7 (Outlet Port).7, E 4-olt plit Flange 1.00, E 4-olt plit Flange M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) #10 E (.875-14) O-Ring #12 E (1 1/16-12) O-Ring #16 E (1 5/16-12) O-Ring ontact factory for other requirements. 10 (rive haft) 1 E traight Keyed,.875 iameter, 1.31 Ext. 5 apered hreaded (1. taper per foot) 7 apered Keyed/hreaded (.6-18 UN, 1. taper per foot) 11 E 13-ooth pline, Major ia. Fit 12 E 13-ooth pline, Flat Root-ide Fit 15 E 11-ooth pline E 9-ooth pline 21 E traight Keyed, 1.00 diameter, 1. ext. 99 E 15-ooth pline, Flat Root-ide Fit ontact factory for other requirements. 11 (Port Locations) 12 (esign esignation) 10 tandard 13 (Rotation) L R ide Inlet / ide Outlet ide Inlet / Rear Outlet (consult factory) Rear Inlet / ide Outlet (consult factory) Rear Inlet / Rear Outlet (consult factory) ounterclockwise Rotation lockwise Rotation 8 (Rear over) 1 tandard ingle Pump Rear over (no options) 9 (haft eal) ingle haft eal (30 PI) ouble haft eal (30 PI) ( mount type only) None High Pressure (1 PI) oncentric -F15 PMP-U-2011-6 5
F19 [174] 6.9 [41] [9].4 [90] 3.5 [14] Ø.6 [1] 5.7 [61] 2.4 [102] Ø 4.0 [] 1.0 [73] 2.9 [20] [17].8.7 [147] 5.8 FRON / IE IE 22 30 IR 1.16 1.34 1.40 1.53 1 7 1.83 2.01 2.14 2.32 2.68 3.05 F15 EION IPLEMEN OE 22 30 4.7 4.8 4.8 4.9 5.0 5.1 5.1 5.2 5.3 5.4 5.7 5.9 118 121 122 1 1 1 130 1 1 1 1 1 [42] [] [59] 2.3 [59] 2.3 RER IE [] [] 1.1 [107] 4.2 6 8 10 11 14 16 27 IR 0.37 1.49 0.61 0.67 0.85 0.98 1.16 1.40 5 1 900 EION IPLEMEN OE 6 8 10 11 14 16 27 2.9 3.0 3.1 3.5 3.6 3.9 4.1 4.2 73 76 79 81 85 88 93 98 104 106 1.0 1.1 1.1 1.2 1.2 1.3 1.4 1.5 26 27 32 41 42 IO IE ll dimensions shown are for reference only. onsult factory for your specific configuration. 6 oncentric -F15 PMP-U-2011-6
Model ode for F19 Ferra eries andem Pumps ORERING INFORMION Each option has been assigned an order code -- listed in the tables below -- for placement in the sequence shown at right. 1 (pecial eals) F3 iton eal Omit tandard 2 (eries) F19 3 (Mount ype) F15 / 900 Ferra eries andem Pump ingle haft eal et Mount (ouble haft eal) EXMPLE: (F3)- F19- - 2 - - - - -11- Q- 12- - 10- L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 pecial eals Ferra eries Mount Front over Front ectio Inlet isplacements Front ection Outlet Rear ection Inlet isplacements Rear ection Outlet rive haft haft eal esign esignation Rotation 4 (Front over) 1 E 2-olt Mount (consult factory) 2 E 2-olt Mount 8 E 2/4-olt ombination Mount (consult factory) 5 (Front ection Inlet Port) 1.00, E 4-olt plit Flange 1., E 4-olt plit Flange 1., E 4-olt plit Flange M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring X #24 E (1 7/8-12) O-Ring ontact factory for other requirements. 6 (Front ection isplacements) m 3 /In 3 m 3 /In 3 cc/1.16 3 cc/2.32 3 cc/1.40 3 cc/2.68 3 cc/1.53 3 cc/3.05 3 cc/1 3 cc/2.01 3 7 (Front ection Outlet Port).7, E 4-olt plit Flange 1.00, E 4-olt plit Flange M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) #10 E (.875-14) O-Ring #12 E (1 1/16-12) O-Ring #16 E (1 5/16-12) O-Ring ontact factory for other requirements. 8 (Rear ection Inlet Port) 16 cc - cc,.75, E 4-olt plit Flange cc - cc, 1, E 4-olt plit Flange 6 cc, #10 E (7/8-14) traight hread 8 cc - 16 cc, #12 E (1-1/16-12) traight hread cc - cc, #16 E (1-5/16-12) traight hread X No Rear Inlet Port (ingle Inlet for ouble Pump) ual inlet for double pump. plit flange ports are not available for 6 cc - 14 cc sizes. Metric ports available, contact factory. 10 (Rear ection Outlet Porting) cc - cc,.7, E 4-olt plit Flange Q 6 cc, #8 E (3/4-16) traight hread 8 cc - 16 cc, #10 E (.875-14) traight hread cc - cc, #12 E (1 1/16-12) traight hread Y 16 cc - cc,.5, E 4-olt plit Flange ontact factory for other requirements. 11 (rive haft) 1 E traight Keyed,.875 iameter, 1.31 Ext. 11 E 13-ooth pline, Major ia. Fit 12 E 13-ooth pline, Flat Root-ide Fit 15 E 11-ooth pline E 9-ooth pline 21 E traight Keyed, 1.00 ia. 99 E 15-ooth pline, Flat Root-ide Fit ontact factory for other requirements. 12 (haft eal) ingle haft eal (30 PI) ouble haft eal (30 PI) ( mount type only) None High Pressure (1 PI) 13 (esign esignation) 10 tandard 11 eal etween ections 14 (Rotation) L R ounterclockwise Rotation lockwise Rotation 9 (Rear ection isplacements) m 3 /In 3 m 3 /In 3 6 6 cc/.366 3 16 16 cc/.976 3 8 8 cc/.488 3 cc/1.159 3 10 10 cc/.610 3 cc/1.403 3 11 11 cc/.671 3 27 27 cc/47 3 14 14 cc/.854 3 cc/09 3 oncentric -F15 PMP-U-2011-6 7
F1515 [41] [174] 6.9 [9].4 [8] 4X.3 [14] 2X Ø.6 [61] 2.4 [1] 5.7 [102] Ø 4.0 [20] 2X.8 [73] 2.9 [147] 5.8 [17].7 FRON / IE IE [59] 2.3 [118] 4.6 [82] [124] Ø 4.9 RER / IO IE 22 30 IR 1.16 1.34 1.40 1.53 1 7 1.83 2.01 2.14 2.32 2.68 3.05 IPLEMEN OE 22 30 3.3 3.3 3.5 3.5 3.7 3.8 F1515 80 82 82 83 85 85 86 87 88 90 93 96 6.0 6.1 6.1 6.2 6.3 6.4 6.4 6.5 6.6 6.7 7.0 7.2 151 154 155 158 161 162 163 166 168 171 177 183 1.5 1.8 1.8 1.9 2.0 2.1 39 40 41 42 43 45 46 48 51 54 3.0 3.1 3.1 3.3 3.6 3.6 3.8 4.0 4.2 75 78 80 82 85 86 87 90 92 95 102 108 ll dimensions shown are for reference only. onsult factory for your specific configuration. 8 oncentric -F15 PMP-U-2011-6
Model ode for F1515 Ferra eries andem Pumps ORERING INFORMION Each option has been assigned an order code -- listed in the tables below -- for placement in the sequence shown at right. 1 (pecial eals) F3 iton eal Omit tandard 2 (eries) F1515 3 (Mount ype) F15 / F15 Ferra eries andem Pump ingle haft eal et Mount (ouble haft eal) EXMPLE: (F3)-F1515- - 2 - -- - -- -12- - 10- L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 pecial eals Ferra eries Mount Front over Front ection Inlet isplacements Front ection Outlet Rear ection Inlet isplacements Rear ection Outlet rive haft haft eal esign esignation Rotation 4 (Front over) 1 E 2-olt Mount (consult factory) 2 E 2-olt Mount 8 E 2/4-olt ombination Mount (consult factory) 5 (Front ection Inlet Port) 1.00, E 4-olt plit Flange 1., E 4-olt plit Flange 1., E 4-olt plit Flange M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring X #24 E (1 7/8-12) O-Ring ontact factory for other requirements. 6 (Front ection isplacements) m 3 /In 3 m 3 /In 3 cc/1.16 3 cc/2.32 3 cc/1.40 3 cc/2.68 3 cc/1.53 3 cc/3.05 3 cc/1 3 cc/2.01 3 7 (Front ection Outlet Port).7, E 4-olt plit Flange 1.00, E 4-olt plit Flange M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) #10 E (.875-14) O-Ring #12 E (1 1/16-12) O-Ring #16 E (1 5/16-12) O-Ring ontact factory for other requirements. 8 (Rear ection Inlet Port) 1.00, E 4-olt plit Flange 1., E 4-olt plit Flange 1., E 4-olt plit Flange M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring X #24 E (1 7/8-12) O-Ring ontact factory for other requirements. 10 (Rear ection Outet Port).7, E 4-olt plit Flange 1.00, E 4-olt plit Flange M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) #10 E (7/8-14) traight hread #12 E (1-1/16-12) traight hread #16 E (1-5/16-12) traight hread 11 (rive haft) 1 E traight Keyed,.875 iameter, 1.31 Ext. 11 E 13-ooth pline, Major ia. Fit 12 E 13-ooth pline, Flat Root-ide Fit 15 E 11-ooth pline E 9-ooth pline 21 E traight Keyed, 1.00 diameter, 1. ext. 99 E 15-ooth pline, Flat Root-ide Fit ontact factory for other requirements. 12 (haft eal) ingle haft eal (30 PI) ouble haft eal (30 PI) ( mount type only) None High Pressure (1 PI) 13 (esign esignation) 10 tandard 11 eal etween ections 14 (Rotation) L R ounterclockwise Rotation lockwise Rotation 9 (Rear ection isplacements) m 3 /In 3 m 3 /In 3 08 3.8 cc/. 3 13.3 cc/.81 3 12 5.7 cc/. 3 32 15.2 cc/.93 3 16 7.6 cc/.47 3 36 17.1 cc/1.04 3 20 9.5 cc/.58 3 24 11.4 cc/.70 3 ontact factory for single inlet applications. oncentric -F15 PMP-U-2011-6 9
F151515 [41] E F [8] 4X.3 [174] 6.9 [9].4 [14] 2X Ø.6 [61] 2.4 [1] 5.7 [102] Ø 4.0 [73] 2.9 [17] [147].7 5.8 FRON / IE IE [20] 3X.8 [59] 2.3 [118] 4.6 [82] [124] Ø 4.9 RER / IO IE ll dimensions shown are for reference only. onsult factory for your specific configuration. 22 30 IR 1.16 1.34 1.40 1.53 1 7 1.83 2.01 2.14 2.32 2.68 3.05 IPLEMEN OE 22 30 3.3 3.3 3.5 3.5 3.7 3.8 80 82 82 83 85 85 86 87 88 90 93 96 6.0 6.1 6.1 6.2 6.3 6.4 6.4 6.5 6.6 6.7 7.0 7.2 F151515 151 154 155 158 161 162 163 166 168 171 177 183 1.5 1.8 1.8 1.9 2.0 2.1 39 40 41 42 43 45 46 48 51 54 4.3 4.4 4.5 4.5 4.7 4.7 4.7 4.9 5.0 5.1 5.3 5.6 109 112 113 115 118 120 121 124 126 1 1 141 E 1.5 1.8 1.8 1.9 2.0 2.1 E 39 40 41 42 43 45 46 48 51 54 F 3.0 3.1 3.1 3.3 3.6 3.6 3.8 4.0 4.2 F 75 78 80 82 85 86 87 90 92 95 102 108 10 oncentric -F15 PMP-U-2011-6
Model ode for F151515 Ferra eries riple Pumps ORERING INFORMION Each option has been assigned an order code -- listed in the tables below -- for placement in the sequence shown at right. 1 (pecial eals) F3 Omit 2 (eries) F151515 3 (Mount ype) iton eal tandard F15 / F15 / F15 Ferra eries riple Pump ingle haft eal et Mount (ouble haft eal) 4 (Front over) 1 E 2-olt Mount (consult factory) 2 E 2-olt Mount 8 E 2/4-olt ombination Mount (consult factory) EXMPLE: (F3)- F151515-2 - - - - - - - X- - - 1- - 10- L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 pecial eals Ferra eries Mount Front over Front ection Inlet isplacements Front ection Outlet Rear ection Inlet isplacements 2nd ection Outlet 3rd ection Inlet isplacements 3rd ection Outlet rive haft haft eal esign esignation Rotation 10 (econd ection Outet Port).7, E 4-olt plit Flange 1.00, E 4-olt plit Flange M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) #10 E (7/8-14) traight hread #12 E (1-1/16-12) traight hread #16 E (1-5/16-12) traight hread 5 (Front ection Inlet Port) 1.00, E 4-olt plit Flange 1., E 4-olt plit Flange 1., E 4-olt plit Flange M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring X #24 E (1 7/8-12) O-Ring ontact factory for other requirements. 6 (Front ection isplacements) m 3 /In 3 m 3 /In 3 cc/1.16 3 cc/2.32 3 cc/1.40 3 cc/2.68 3 cc/1.53 3 cc/3.05 3 cc/1 3 cc/2.01 3 11 (hird ection Inlet Port) 1.00, E 4-olt plit Flange 1., E 4-olt plit Flange 1., E 4-olt plit Flange M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring X #24 E (1 7/8-12) O-Ring ontact factory for other requirements. 12 (hird ection isplacements) m 3 /In 3 m 3 /In 3 cc/1.16 3 cc/2.32 3 cc/1.40 3 cc/2.68 3 cc/1.53 3 cc/3.05 3 cc/1 3 cc/2.01 3 7 (Front ection Outlet Port) 13 (hird ection Outet Port).7, E 4-olt plit Flange.7, E 4-olt plit Flange 1.00, E 4-olt plit Flange 1.00, E 4-olt plit Flange M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) M 1.00, E 4-olt Metric plit Flange (M10 x 1. threads) #10 E (.875-14) O-Ring #10 E (7/8-14) traight hread #12 E (1 1/16-12) O-Ring #12 E (1-1/16-12) traight hread #16 E (1 5/16-12) O-Ring #16 E (1-5/16-12) traight hread ontact factory for other requirements. 14 (rive haft)* 8 (Rear ection Inlet Port) 1 E traight Keyed,.875 iameter, 1.31 Ext. 1.00, E 4-olt plit Flange 12 E 13-ooth pline, Flat Root-ide Fit 1., E 4-olt plit Flange 21 E traight Keyed, 1.00 diameter, 1. ext. 1., E 4-olt plit Flange 99 E 15-ooth pline, Flat Root-ide Fit M 1., E 4-olt Metric plit Flange (M14 x 2.0 threads) 15 (haft eal) #16 E (1 5/16-12) O-Ring #20 E (1 5/8-12) O-Ring ingle haft eal (30 PI) X #24 E (1 7/8-12) O-Ring ouble haft eal (30 PI) ( mount type only) ontact factory for other requirements. None High Pressure (1 PI) 9 (econd ection isplacements) 16 (esign esignation) m 3 /In 3 m 3 /In 3 cc/1.16 3 cc/2.32 3 10 tandard cc/1.40 3 cc/2.68 3 11 eal etween ections cc/1.53 3 cc/3.05 3 17 (Rotation) cc/1 3 cc/2.01 3 L ounterclockwise Rotation * ontact factory for other requirements. ee #14 rive haft. R oncentric -F15 PMP-U-2011-6 lockwise Rotation 11
MOUNING FLNGE E 2-OL.47 [11.94] R. 4 PLE.36 [9.14].36 [9.14] 2.094 [53.] 2.094 [53.] 3.75 [95.] ia..4 [11.13] ia. thru 2 places as shown 48 [82.55] [82.]. [12.7] Mounting flange thickness.240 [6.10]. [8.] eal drain hole onsult factory for availability. E 2-OL R..57 [14.40] 4 PLE. [12.7]. [12.7] 2.87 [73.00] 4.000 3.998 [100] [101.54].37 [9.40] 2.87.32 [73.00] [8.10] eal drain hole onsult factory for availability..65 Mounting Flange hickness [16.56] E 2/4-OL 2.4 [57.] 2.4 [57.] 2.4 [57.] 3.56 [90.48] 2.4 [57.] 3.56 [90.48].61 [15.5].61 [15.5] R..64 [16.3] 4 PLE 5.000 4.998 [127.00] [126.95].49 [12.45].32 [8.1]. [12.7] Mounting Flange hickness onsult factory for availability. 12 oncentric -F15 PMP-U-2011-6
RIE HF E RIGH KEY haft No. 1: For F15, F19 & F1515 Pumps 2.6 Nm (90 lb.) torsional capacity.* E INOLUE PLINE haft No. 12: For F15, F19 & F1515 Pumps 279.6 Nm (2475 lb.) torsional capacity.* [41.15] 2 1.312 [.32] 1.062 [26.97] full depth.2 [6.6] sq. / 1.00 [.40] long key.987 [.07].977 [24.82].030 [.76].020 [.51] R..875.874 [22.22] [22.20] ia. [12.7]. [41.15] 2.060 [1.52] x 45.060 [1.52].090 [2.] [.32] 1.312 R. Flat Root - ide Fit No. of eeth - 13 iametral Pitch - 16/32 Pressure ngle - 30 E - INOLUE PLINE haft No. 99: For F15, F19, F1515 & F151515 Pumps 451.9 Nm (4000 lb.) torsional capacity.* [45.97] 1.81 [.10] 1. [12.7]. Flat Root - ide Fit No. of eeth - 15 iametral Pitch - 16/32 Pressure ngle - 30 * pplies to coaxial applications only. onsult representative if application requires greater capacity or has side loads. For shaft options not shown, contact factory for specific shaft information. oncentric -F15 PMP-U-2011-6 13
Overall (%) Mechanical (%) olumetric (%) echnical Performance ata F15 Pumps 100% 2000 psi [1 bar] 3000 psi [207 bar] 4000 psi [276 bar] 0 psi [34 bar] 90% 80% 70% 0 1000 2000 RPM 3000 4000 100% 90% 2000 psi [1 bar] 3000 psi [207 bar] 4000 psi [276 bar] 80% 0 psi [34 bar] 70% 0 1000 2000 RPM 3000 4000 100% 90% 2000 psi [1 bar] 3000 psi [207 bar] 4000 psi [276 bar] 80% 0 psi [34 bar] 70% 0 1000 2000 RPM 3000 4000 14 oncentric -F15 PMP-U-2011-6
PUMP & MOOR ast Iron Pumps Heavy uty luminum Pumps Medium/Light uty G eries Pumps isplacements 0.065 to 0.711 cu. In. (1.06 to 15 cc) G eries High/Low Pumps High Pressure isplacements 0.065 to 0.8 cu. In. (1.06 to 4.22 cc) Low Pressure isplacements 0.8 to 0.776 cu. In. (4.22 to 12.71 cc) Maximum Pressure 4,000 psi (276 bar) Maximum peed 4,000 rpm F12 & F15 Ferra eries Pumps F12 isplacements 0.976 to 2.2 cu. In. (16 41 cc) F15 isplacements 1.159 to 3.051 cu. In. ( to cc) Maximum Pressure 4,000 psi (276 bar) Maximum peed 3,600 rpm F20/F30 Pumps & F20-L/F30-L Load ense Ferra eries Pumps isplacements 1.41 to 9.82 cu. In. ( to 161 cc) Maximum Pressure 4,000 psi (276 bar) Maximum peed 3,600 rpm eries Pumps isplacements 0.2 to 1.395 cu. In. (3.80 to 22.85 cc) eries High/Low Pumps High Pressure isplacements 0.465 cu. In. (7.62 cc) Low Pressure isplacements 0.930 to 1.395 cu. In. (15.24 to 22.86 cc) Maximum Pressure 3,000 4,000 psi (207 276 bar) Maximum peed 3,600 4,000 rpm all us for more information For application assistance or detailed literature on any oncentric product line, call us toll-free: 1-800-572-7867. isit our web site: http://www.concentric.com E-mail us: info.hydraulics.us@concentric.com -eries Pumps 100 isplacements 0.031 to 0.122 cu. In. (0. to 2.00 cc) 300 isplacements 0.049 to 0.347 cu. In. (0.80 to 5.70 cc) 600 isplacements 0.2 to 0.732 cu. In. (4 to 12 cc) 900 isplacements 0.305 to 1.891 cu. In. (5 to 31 cc) 1200 isplacements 1.526 to 2.014 cu. In. ( to cc) 10 isplacements 1.159 to 3.051 cu. In. ( to cc) Maximum Pressure 4,000 psi (276 bar) Maximum peed 0 to 4,000 rpm Q900 Pumps isplacements 0.305 to 48 cu. In. (5 to 27 cc) Maximum Pressure 3,6 psi (0 bar) Maximum peed 4,000 rpm Fluid Motors ast Iron isplacements 0.065 to 9.82 cu. In. (1.06 to 161 cc) peed Up to 10,000 rpm luminum isplacements 0.2 to 3.0 cu. In. (4 to cc) peed Up to 4,000 rpm Flow ividers G & eries G isplacements 0.097 to 0.517 cu. In. (1.58 to 8.47 cc) isplacements 0.2 to 0.813 cu. (3.8 to 13.32 cc) Maximum Pressure 4,0 psi (310 bar) Maximum Input Flow Per ection 14 gpm (53 lpm) oncentric -F15 PMP-U-2011-6 15
PROU RNGE HE Powerpacks 12/24/48 0.3 4.5 k and 0.75 3 k modular power packs HE ox Powerpacks 12/24/48 modular powerpacks in weatherproof boxes Pressure witches 5-3 bar, connecting/disconnecting 100 Hydraulic pumps 0,5-2,0 cc 227 bar www.concentric.com 300 Hydraulic pumps 0,8 5,7 cc 0 bar 600 Hydraulic pumps / motors 3 12 cc 276 bar 900 Hydraulic pumps / motors 5 31 cc/section 276 bar alma he new quiet pumps 6,2 -,7 cc/section 2 bar Q900 he quiet pumps 5 - cc/section 0 bar P900X Hydraulic pumps 16-31 cc/section 276 bar oncentric Rockford orp. 2222 15th treet ROKFOR, IL 61104 U el: +1-815 398 00 Fax: +1-815 398 5977 E-mail: info.hydraulics.us@concentric.com oncentric kanes ox 95 E-0 40 K. FGERHUL weden el: +46-4 32400 Fax: +46-4 30546 E-mail: info.hydraulics.eu@concentric.com oncentric Hof GmbH Postfach 17-914 HOF Germany el: +49-91 895-0 Fax: +49-91 871 E-mail: info.hydraulics.eu@concentric.com oncentric uzhou o. Ltd. 47 ongjing Industrial Park 9 ong Fu Lu IP, uzhou Jiangsu hina 2151 el +86 512 8717 5100 Fax +86 512 8717 5101 info.chsh@concentric.com 10 Hydraulic pumps / motors - cc/section 276 bar F12 FERR Heavy duty pumps 16-41 cc/section 276 bar F15 FERR Heavy duty pumps - cc/section 276 bar F20/F30 (L) Hydraulic pumps / motors 161 cc/section 276 bar GP Internal Gear pumps 1,7 63 cc/section 100 bar G Hydraulic pumps / motors 1,06 11,65 cc/section 276 bar Hydraulic pumps 3,8 22,9 cc/section 207 bar oncentric -F15 PMP-U-2011-6 H Hydraulic pumps 9,8 39,4 cc/section 207 bar II-tage Hydraulic pumps 4,2 22,8 cc/section 276 bar Rotary Flow ividers 3,8 13,3 cc/section 300 bar ransmission pumps oncentric is an innovator in flow control and fluid power, supplying proprietary systems and components for trucks, buses and industrial vehicles, worldwide. ith 1,156 employees and yearly sales exceeding 1,977 million wedish Kronor, oncentric is listed on the tockholm tock Exchange (www.concentric.com). oncentric will not accept responsibility for any catalog errors and reserves the right to modify its products without prior notice. his also applies to products already ordered, provided that such modifications can be made without affecting technical specifications. ll trademarks in this material are properties of their respective owners.