INSTALLATION INSTRUCTIONS Accessory NIGHT Application CR-V Publications No. AII 32951 Issue Date SEP 2006 PARTS LIST Automatic Day/Night Mirror Attachment Kit P/N 08V03-SWA-100 Harness cover set Automatic Day/Night Mirror Kit P/N 08V03-S9A-100B Day/Night mirror Automatic Day/Night mirror harness Operating Instructions TOOLS AND SUPPLIES REQUIRED 9 Wire ties 4 EPT sealers Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Isopropyl alcohol Shop towel Diagonal cutters T-20 and T-25 TORX bits Needle nose pliers Steel wire Clip Ground bolt 2006 American Honda Motor Co., Inc. All Rights Reserved AII 32951 (0609) 08V03-SWA-1000-91 1 of 8
Illustration of the Day/Night MIirror Installed on the Vehicle 3. Carefully remove the right and left map light lens from the roof console (four tabs for each lens). DAY/NIGHT ROOF CONSOLE TABS (4) TABS (4) 6312070B MAP LIGHT LENS RIGHT MAP LIGHT LENS 6308150Y INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down radio station presets. 2. Disconnect the negative cable from the battery. 4. Remove the roof console (four bolts and unplug the vehicle connectors). ROOF CONSOLE SILVER BOLTS BLACK BOLTS 6313021Y 2 of 8 AII 32951 (0609) 2006 American Honda Motor Co., Inc. All Rights Reserved
5. Remove the cover from the left sunvisor (four retaining tabs). 8. Remove the cover from the mirror (two retaining tabs). Lift up the mirror while pulling the base, and remove the mirror. TABS (4) TABS (2) COVER Lift up. BASE Pull. COVER SUNVISOR TORX SCREWS 6311 6. Remove the two T-25 TORX screws, pull out the left sun visor, and remove the sunvisor. 7. Remove the right and left sunvisor holders. Using a flat-tip screwdriver, push in on the tab and rotate the holder. BASE 6823040B SUNVISOR HOLDER 9. Using a flat-tip screwdriver, remove the two caps from the left front grab rail. FLAT-TIP SCREWDRIVER Push. FLAT-TIP SCREWDRIVER Turn. SUNVISOR HOLDERS (2) RIGHT SUNVISOR HOLDER 6308170Y CAPS (2) GRAB RAIL GRAB RAIL CAP 6311161B 2006 American Honda Motor Co., Inc. All Rights Reserved AII 32951 (0609) 3 of 8
10. Using needle nose pliers, remove the left front grab rail (two clips). GRAB RAIL S (2) 12. Remove the left A-pillar trim (two clips). S (2) NEEDLE NOSE PLIERS DOOR OPENING SEAL GRAB RAIL 6311170B 11. Remove the front door opening seal around the A-pillar trim. Using a rubber mallet, strike the top of the A-pillar trim, in the area marked SIDE CURTAIN AIRBAG, to release the clip. Remove the clip. A-PILLAR TRIM 13. Remove the left front door sill trim (three clips). S (3) 6311181B TAB Collapsed. Remains on the vehicle panel. TAB Tap. BODY PIN Comes off from the clip. Pull. BODY Pushed deep behind the vehicle panel. BODY DOOR SILL TRIM 6303090B DOOR OPENING SEAL PART MARKED AS SIDE CURTAIN AIRBAG A-PILLAR TRIM Tap at right angles to the vehicle. Tap with a rubber mallet. 4 of 8 AII 32951 (0609) 2006 American Honda Motor Co., Inc. All Rights Reserved
14. Remove the front door opening seal from around the left kick panel. Remove the left kick panel (two clips). DOOR OPENING SEAL S (2) NOTE: If another accessory is already plugged into the 6- pin connector opening of the fuse box, remove the dummy connector from the 6-pin connector taped to the automatic day/night mirror harness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the automatic day/night mirror harness you just unplugged and plug the automatic day/night mirror harness into the 6-pin connector opening of the fuse box. 6-PIN OPENING of the OTHER ACCESSORY 6-PIN KICK PANEL 6303100B 15. Plug the automatic day/night mirror harness 6-pin connector into the empty 6-pin connector opening of the fuse box. OPEN 6-PIN OPEN 6-PIN 6-PIN DUMMY 16. Attach a piece of steel wire to the automatic day/ night mirror harness, and route it through the left front pillar trim opening. PILLAR TRIM OPENING STEEL WIRE 6-PIN 6312022B NIGHT 6627080B 2006 American Honda Motor Co., Inc. All Rights Reserved AII 32951 (0609) 5 of 8
17. Route the automatic day/night mirror harness behind the fuse box. 19. Route the automatic day/night mirror harness above the headliner from the left A-pillar to the middle of the vehicle. 6627090B 18. Remove the steel wire. Route the automatic day/ night mirror harness along the vehicle harness as shown. Loosely secure the day/night mirror harness to the vehicle harness with the four wire ties. HEADLINER A-PILLAR 7-PIN 6311191B 20. Plug the automatic day/night mirror into the day/night mirror 7-pin connector. 7-PIN BASE A- PILLAR WIRE TIE PILLAR TRIM OPENING 682301 TORX SCREW Up. 6311202B 21. Install the day/night mirror on the mirror base, then tighten the T-20 TORX screw installed in the day/night mirror. 6 of 8 AII 32951 (0609) 2006 American Honda Motor Co., Inc. All Rights Reserved
22. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the EPT sealer will attach. Secure the automatic day/night mirror harness to the headliner with three EPT sealers. 25. Remove the vehicle bolt from the fuel lid opener. Attach the automatic day/night mirror harness ground terminal with the ground bolt supplied. EPT SEALER GROUND BOLT BOLT (Not used.) HEADLINER FUEL LID OPENER 6311211B NIGHT GROUND TERMINAL 6823030B 23. Pull the slack in the automatic day/night mirror harness down the A-pillar to the fuse box. Tighten the four wire ties installed in step 18. 24. Secure the automatic day/night mirror harness to the vehicle harness with the two wire ties in the areas shown. 26. Install the harness cover to the automatic day/night mirror and the headliner. HEADLINER COVER WIRE TIE 6312062B WIRE TIE 6312042B 2006 American Honda Motor Co., Inc. All Rights Reserved AII 32951 (0609) 7 of 8
27. Remove and discard the upper vehicle clip from the left A-pillar. A-PILLAR Remove. 30. Check that all wire harnesses are routed properly and all connectors are plugged in. 31. Reinstall all removed parts. 32. Reconnect the negative cable to the battery. 33. Enter the customer s audio and navigation system (if equipped) anti-theft codes, and reset the XM radio presets. 34. Reset the clock. NOTE: Check the operation of the automatic day/night mirror according to the Operating Instructions supplied. Place the Operating Instructions in the glove box for your customer. A-PILLAR TRIM PIN 6305010H 28. Check that the left A-pillar trim and the pin are not damaged, then, install the new clip from the kit on the pin. 29. Position the clip at right angles near the hole in the left A-pillar. Install the clip by lightly pushing the left A-pillar trim at the part marked as SIDE CURTAIN AIRBAG. Check that the airbag is not pinched with the clip, and be careful not to push the left A-pillar trim excessively A-PILLAR PANEL PART MARKED AS SIDE CURTAIN AIRBAG A-PILLAR TRIM 65190 8 of 8 AII 32951 (0609) 2006 American Honda Motor Co., Inc. All Rights Reserved