Four Post Surface Lift

Similar documents
Operating Instructions

2-Post Lift Operations and Maintenance Manual

Operating Instructions

ATO7 (100 Series Lifts)

Operating Instruction Electro hydraulic workshop presses HPE

SPOA10NB, SPOA10, SPO10 ( Series Lifts) SPOA7, SPOA9, SPO9 (500 Series Lifts)

Minimum quantity lubrication system MVE for external lubrication. Operation manual

O P E R A T I N G M A N U A L

SL210i/SL212i/SL19i. Table Of Contents

Minimum quantity lubrication system MDE for external lubrication. Operation manual

ASSEMBLY & OPERATION INSTRUCTION MANUAL

CR30 Installation Instruction Capacity 30,000 lbs. (15,000 lbs. per axle) 235 /271 /308 Wheelbases 140 Minimum Wheelbase

STARPOINT. Safety instructions. Starpoint VRS (-F) Fax: Phone:

CR18 Installation Instructions

RFID114. For use in combination with charge controllers used in electric vehicle charging stations, wall boxes or street light charging points.

ATD2P11BS. Two-Post Clear Floor Bi-Symmetric Automotive Lift. Installation & Operation Manual. 11,000 lbs. Capacity. (2,750 lbs.

Load Ring for bolting >VLBG<

Load Ring for bolting >VLBG-PLUS<

Operating and maintenance instructions

SM88 I N S T A L L A T I O N I N S T A L L A T I O N I N S T R U C T I O N S I N S T R U C T I O N S

ATTENTION. 1. Do not attempt to use the power unit to extend your cylinder. This must be done manually.

>IVH< >VVH< Shortening hook

AR123/SM123 I N S T A L L A T I O N I N S T A L L A T I O N I N S T R U C T I O N S I N S T R U C T I O N S

O P E R A T I N G. 4-Post Lift SM40, SM40LT, SM60 A N D M A I N T E N A N C E M A N U A L. Rotary Lift, June 2011 CO6941.

Betriebsanleitung Operating Instructions. Diaphragm Pump

CORDLESS FLARING TOOL

> VIP-Balancer < VIP-Balancer. VIP-Balancer

SCISSOR LIFT Model MR6K-38 /161108A 6,000lb Capacity Operation Manual

Read this entire manual before operation begins.

( Series) Capacity 18,000 lbs. (9,000 lbs. per axle) Four Post Surface Mounted Lift Maximum Wheelbases: 194" & 230" Minimum Wheelbase: 126"

Four Post Surface Mounted Lift Capacity 14,000 lbs. (7,000 lbs. per axle)

Load Ring for bolting >VLBG<

MODEL L401 & L404 Four-Post Lift

B38 01/12. Installation and Operating Instructions Combi Gauges for Rail Cars Models Rg Fz, RChg Fz, DRg Fz, DRChg Fz. Contents

BLAZER 9000 LUBE LIFT OPERATOR AND PARTS MANUAL

Operating Instructions. TM Girder Clamps

Support T10552 T10595 T40386

Installation Instructions Capacity 10,000 lbs. (100 Series Lift)

Installation Instructions X-Force UTV Lift (000 Series) Capacity 2,275 lbs (1,035 kg)

Atlas PV-9WP Addendum

Instruction Manual for Microlitre Centrifuge Z 160 M

Printed: Doc-Nr: PUB / / 000 / 00

NOTE Please read this Operating Manual carefully before first using the device and strictly adhere to the instructions!

3. Operating instructions: Minor 200

Instruction Sheet. 1/2 HP Portable Electric Pumps SAFETY FIRST. L2062 Rev. F 02/ IMPORTANT RECEIVING INSTRUCTIONS 2.

Heavy Duty Engine Cranes

TM 60 TS 75 TS 100 Please read this user guide before using your operator. Please read carefully the security advises on the following pages!

Operating instructions Solenoid interlock TKM/TKF. 1. About this document. Content

Installation Instructions Capacity 10,000 lbs. DP10 (200 Series Lift)

Dumper OPERATOR S MANUAL

CONTENTS. Product Features and Specifications Installation Requirement Steps of Installation 4. Exploded View Test Run...

Parallel Lift Rack MODEL RM

Read this entire manual before operation begins.

Conveyor Belts / Hops Silo Types: N 10, BOF / types: H series

TWO POST LIFT 7,000 LBS.

Operating manual FP-2. Index

Electro-Hydraulic / UTV Lift Bench U-2200IEH-XR

Sugar beet covering eqipment

Crane fork KGM/KGA and KGQ/KGL

15,000kg HYDRAULIC BOTTLE JACK

Dumper 1001, 1501, 2001 OPERATOR S MANUAL

SIP Direct Drive Oil-Lube Air Compressors - Operating & Maintenance Instructions

Max-Upender/Tilt Series Service Manual

CONTENTS. Product Features and Specifications...1. Installation Requirement Steps of Installation.. 5. Exploded View Test Run...

Hydraulic Hand Pallet Trucks

Operating instructions

CONTENTS. Product Features and Specifications Installation Requirement Installation Exploded View Operation Instruction...

Operating instructions Solenoid interlock AZM 161../.. 1. About this document. Content

Read this entire manual before operation begins.

CAUTION -TABLE OF CONTENTS- II. OPERATING INSTRUCTIONS

CONTENTS. Product Features and Specifications...1. Installation Requirement...3. Steps of Installation...4. Exploded View Test Run...

HYDRAULIC PALLET TRUCK MODEL NO: PT540M/BM/CM & PT685BM/CM PART NO: , , , ,

AIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST

Grease Stand MODEL# DF MAINTENANCE AND OPERATION MANUAL. Page 1

Powerflare Caution Light

SPO15, SPO18 I N S T A L L A T I O N I N S T R U C T I O N S

HEAVY DUTY TROLLEY JACK. Operation Manual

Operating and Maintenance Manual. for. HADEF overhead crane. as jointed crane TA

Installation Instructions

HST -LS Interlocking device (Translation of Original Manual)

1.5 TON ALUMINUM RACING JACK


OPERATING INSTRUCTION

1000-LB. ENGINE STAND

PROFESSIONAL BOTTLE JACK

Installation, operation and maintenance manual

TWO POST LIFT INSTALLATION AND OWNERS MANUAL

Read this entire manual before operation begins.

Operating instructions Safety sensor BNS About this document. Content. 6 Disassembly and disposal 6.1 Disassembly Disposal...

Floor Plate Style Lift And Overhead Beam Style Lift. Two Post Lift

Read this entire manual before operation begins.

Operating instructions

2000-LB. ENGINE STAND

IBT Series Square Drive Torque Wrenches

6L Oil-less Air Compressor 53103

TXJ0500/RR500 1,000-lbs. Truck Bed Roller Dolly

SAUTER TVO Version /2014 GB

Hydraulic Wheel Dolly

TWO POST LIFT INSTALLATION AND OWNERS MANUAL Capacity 10,000 lbs.

ABSOLUTE EQUIPMENT PTY LTD

Transcription:

O PE Four Post Surface Lift SM40/AR40/SM55/AR55/AR55W R A TI O N & M AI N TE Table of Contents LIFT CONTROLS...3 N A N C E Operating Instructions...4 RESIDUAL RISKS...5 Maintenance Instructions...7 LP20100 October 2010 by Vehicle Service Group. All rights reserved. CO7799 OM20121 Rev. D 10/28/10 M AN U A L

Only those technicians who have been properly trained in the usage and care of the lift should be allowed to operate the lift. Local regulations MAY require that the operator be at least 18 years of age and be supervised by a trained operator while: a. Positioning the vehicle in the service bay, B. Actuating the lift controls. The lift is to be used indoors for raising unoccupied motor vehicles ONLY! ONLY lift vehicles which have an individual axle weight that does not exceed one-half the lift capacity. See load capacity table below. MODEL SM40 AR40 SM55 AR55 AR55W LOAD CAPACITY 4000kg 4000kg 5500kg 5500kg 5500kg 2

Lift Controls 1 Turning Disconnect to the right provides electricity to the motor. 2 Pushing button starts the motor and raises the runways. 3 Pushing button lowers to locks. 4 Pushing button raises lift, retracts locks and lowers runways to 200mm from floor. 5. Pushing button lowers lift from 200mm until runways are lowered to the floor. 6. Remove cap to fill or add fluid to power unit tank. Incoming Air Incoming Power Control Panel 1. Switch 2. Raise Switch 4. Lower Switch 3. Lower To Lock 5. Toe Guard Down 6. Fill/Breather Cap CAPACITY 4000 kg. Capacity Sticker Column Fig. 1 3

WARNING To avoid personal injury and/or property damage, permit only trained personnel to operate lift. After reviewing these instructions, get familiar with lift controls by running the lift through a few cycles before loading vehicle on lift. 1. Before Loading: Inspect Lift - See "Operator Maintenance" on page 6. Never operate if lift malfunctions or has broken or damaged parts. Lift must be fully lowered and service bay clear of all personnel before the vehicle is positioned onto lift. Assure area around lift is free of tools, debris, grease, and oil. If lift is equipped with rolling jacks, jacks must be fully lowered and the rear jack pushed toward center of lift to provide under car clearance. Operating Instructions Surface Mounted Wheel Engaging Lifts Note: Allow 2 seconds between motor starts. Failure to comply may cause motor burnout. Continue to raise to desired height. Lower lift onto locks after desired height is reached. 4. While Using Lift: Always use safety stands as needed for stability when removing or installing heavy components. (i.e.: engines, transmissions, etc.) Use 4 safety stands. Raise safety stands to meet vehicle, do not lower vehicle onto stands. Do Not allow unauthorized persons in shop area while lift is in use. Do Not use any part of the lift as a crane or as a support for another lifting mechanism. (i.e.: block & tackle, etc.) 2. Loading: The operator of the lift is required to be at least 18 years of age, and must have been instructed by a trained operator. Do Not allow unauthorized or untrained persons to position vehicle or operate lift. Do Not overload lift. See capacity label on lift. Drive vehicle onto lift and stop vehicle when it is centered on runway. At all times, be sure rear wheels are forward of the ramp/chocks and the ramp/chocks will clear tires when the lift is raised, Fig. 2. Put vehicle in park, engage parking brake and place triangular wheel chocks on each side of one of the rear tires, Fig. 2. Avoid accidental touching of exposed exhaust system on raised vehicles. Watch for air hoses and electrical cords which may be tripped over. Wear safety glasses while working under vehicle. 5. Before Lowering Lift: Remove all tools or other objects from lift area. Assure personnel are not in lift area. 6. To Lower Lift: Remain clear of lift when lowering vehicle. Keep Feet Clear! Push lower switch to lower, Fig. 1. 7. Unloading: Fully lower lift. Remove triangular wheel chocks. Assure Exit area is clear of objects and personnel before removing vehicle from lift. Carefully drive vehicle off lift. Wheel Chock Ramp/Chock 8. Power Off: Turn switch to "OFF" position while lift is not in use. Fig. 2 3. To Raise Lift: Do Not permit anyone on lift or inside vehicle when it is being raised (or lowered). 9. Trouble Shooting: See page 7. 10. Maintenance: See page 7. Maintain visual contact with lift & vehicle throughout the motion of the lift while remaining clear of lift. Push Raise switch on power unit, Fig. 1. 4

RESIDUAL RISKS Assure cargo does not cause either individual axle weight to exceed two thirds lift capacity. 5

OPERATOR INSPECTION & MAINTENANCE (MAINTENANCE AUTHORIZED BY OPERATOR) Always keep bolts tight. Check periodically. Always raise lift when cleaning floor area with solvents and/ or cleaning compounds. Always keep lift components clean. Daily: Check locking latch operation and reset. If not operating properly, call local service representative. Daily: Check for permanent deformation of slack cable arms (see below). If present, call local service representative to replace parts. Always, if fluid leakage is observed, call local service representative. Daily: Check cables and sheaves for wear. If parts are damaged or worn, call local service representative to replace. Daily: Inspect front wheel stops and ramp/chocks for damage or excessive wear. If parts are damaged or worn, call local service representative to replace. Monthly: Check slack cable switches for function. Every 3 Months: Check anchor bolts for tightness. Anchors should be torqued to 61 N - m. Every 6 months: Check fluid level of lift power unit and refill to proper level in level indicator with lift fully lowered. Replace all decals on the lift if unable to read or missing. Reorder labels from Rotary Lift. Replace if bent NOTE: LIFT SHOULD RAISE LEVEL. IF LIFT IS NOT RAISING LEVEL, CHECK CABLES FOR STRETCH. CABLES MAY NEED ADJUSTMENT (BY AUTHORIZED PERSONNEL). MOST CABLE STRETCH OCCURS DURING THE FIRST 30-90 DAYS OF LIFT USE. 6

Trouble Shooting (for OPERATORS) Trouble Motor does not run. Motor runs but will not raise lift. Motor runs raises unloaded lift but will not raise vehicle. Lift slowly settles down. Slow lifting speed or fluid blowing out filler breather cap. Lift going up unlevel. Anchors will not stay tight. Locking latches do not engage. Locking latches do not disengage. Cause Blown fuse or circuit breaker. Low fluid level. Overloading lift. See Remedy See Remedy See Remedy See Remedy See Remedy See Remedy Remedy 1. Replace blown fuse or reset circuit breaker. 2. Contact service representative for 1. Fill tank with Dexron III ATF or equivalent. 2. Contact service representative for 1. Check vehicle weight and/or balance vehicle weight on lift. 2. Contact service representative for Contact service representative for Contact service representative for Contact service representative for Contact service representative for Contact service representative for Contact service representative for 7

REPAIR MAINTENANCE (MAINTENANCE AUTHORIZED BY QUALIFIED SERVICE REPRESENTATIVE ONLY) Lockout any energy sources before beginning any repairs. DO NOT modify the lift in any manner without the prior written consent of the manufacturer. If electrical problems develop, make repairs according to local electrical codes. Use genuine Rotary Lift parts when replacement is necessary. Cable adjustment should be checked by a Rotary Authorized Installer after the first 50 loaded lift cycles and after 300 loaded lift cycles. Adjust cable tension per lift installation instructions. Monthly: Lubricate locking latch shafts. Activate latches several times for oil to penetrate joints. Replace worn parts as required with genuine Rotary parts. Annual Inspection (performed by Authorized Personnel) Aside from the routine checks that are stated under "Operator Maintenance", the following annual inspection is to be performed and a record of this inspection permanently retained on site. All deficiencies are to be corrected by the proper authorized personnel. Inspection Points Check accessibility of the operating procedures. Check accessibility and readability of all labels. Check the rated load capacity of the lift. Examine all structural components including welds. Check electrical cords for insulation damage. Check fluid level. Check the lift controls for function. Check all fastening devices for tightness including floor anchor bolts. Check exposed surfaces and edges. Operate the lift and check the operation of the positive stop and the lift safety latches. With a representative vehicle on the lift, check the lowering speed (not to exceed 0.15 m/s). With a representative vehicle on the lift, check cable tension adjustment. Check the function of slack cable switches. Check all accessible piping, tubing, hose, valves and fittings. Review lift fluid consumption records. Operate lift through full excursion and observe. * With lift loaded, stop the lift at midpoint of travel and observe for drifting down and hydraulic leaks. Check with operator to ascertain any unusual operating characteristics. * Perform check with and without a vehicle representative load. 8

Trouble Shooting (For AUTHORIZED MAINTENANCE PERSONNEL) Trouble Cause Remedy Motor does not run. Motor runs but will not raise lift. Motor runs raises unloaded lift but will not raise vehicle. Lift slowly settles down. Slow lifting speed or fluid blowing out filler breather cap. 1. Incorrect voltage to motor. 2. Bad wiring connections. 3. Motor up switch fault. 4. Overhead limit switch fault. 5. Motor windings burned out. 1. Open lowering valve. 2. Pump sucking air. 3. Suction tube off pump. 1. Motor running on low voltage. 2. Debris in lowering valve. 3. Improper relief valve adjustment. 1. Debris in check valve seat. 2. Debris in lowering valve seat. 3. External fluid leaks. 1. Air mixed with fluid. 2. Air mixed with fluid suction. 3. Fluid return tube loose. 1. Supply correct voltage to motor. 2. Repair and insulate all connections. 3. Check switch. 4. Check switch. 5. Replace motor. 1. Repair or replace lowering valve. 2. Tighten all suction line fittings. 3. Replace suction tube. 1. Supply correct voltage to motor. 2. Clean lowering valve. 3. Adjust relief valve. 1. Clean check valve. 2. Clean lowering valve. 3. Repair external leaks. 1. Change fluid to Dexron III ATF or equivalent. 2. Tighten all suction line fittings. 3. Reinstall fluid return tube. Lift going up unlevel. Anchors will not stay tight. If Lift stops short of full rise or chatters. Lift will not lower. 1. Equalizer cables out of adjustment. 2. Lift installed on unlevel floor. 1. Holes drilled oversize. 2. Concrete floor thickness or holding strength not sufficient. Fluid level may be low. 1. Insufficent air supply to lift. 2. Latches out of adjustment. 1. Adjust equalizer cables to correct tension. 2. Shim lift to level columns (Not to exceed 12.7 mm). If over 12.7mm. Break out floor and level per lift installation instructions. 1. Relocate lift using a new bit to drill holes. 2. Break out old concrete and repour new pads for lift per lift installation instruction. Check fluid level and bleed both cylinders per lift installation instructions. 1. Check air pressure. Air supply should be 6.2-8.3 bar. Check air lines for leaks or crimps. 2. Check latches. 9

EG-Konformitätserklärung EC Declaration of Conformity im Sinne der EG-Richtlinie 2006/42/EG über Maschinen (Anhang II A) according to EC directive 2006/42/EC on machinery (Annex II A) Name und Anschrift des Herstellers Name and address of the manufacturer: Name und Anschrift seines in der EU niedergelassenen Bevollmächtigten his authorised representative in EU Rotary Lift BlitzRotary GmbH 2700 Lanier Drive Hüfinger Str.55 Madison, IN, 47250 USA 78199 Bräunlingen, Germany Diese Erklärung bezieht sich nur auf die Maschine in dem Zustand, in dem sie in Verkehr gebracht wurde; vom Endnutzer nachträglich angebrachte Teile und/oder nachträglich vorgenommene Eingriffe bleiben unberücksichtigt. Die Erklärung verliert ihre Gültigkeit, wenn das Produkt ohne Zustimmung umgebaut oder verändert wird. This declaration relates exclusively to the machinery in the state in which it was placed on the market, and excludes components which are added and/or operations carried out subsequently by the final user. The declaration is no more valid, if the product is modified without agreement. Hiermit erklären wir, dass die nachstehend beschriebene Maschine Herewith we declare, that the machinery described below Produktbezeichnung / product denomination: 4-Säulen-Hebebühne / 4-post vehicle lift Serien- / Typenbezeichnung / model / type: SM55 Tragfähigkeit 5500 kg / capacity 5500 kg AR55 Tragfähigkeit 5500 kg / capacity 5500 kg AR43 Tragfähigkeit 4000 kg / capacity 4000 kg Maschinen-/Seriennummer / machinery / serial number:.. Baujahr / Year of manufacture: 20 allen einschlägigen Bestimmungen der Maschinenrichtlinie 2006/42/EG entspricht. Die Maschine entspricht zusätzlich den Bestimmungen der Richtlinien 2004/108/EG über elektromagnetische Verträglichkeit und 2006/95/EG über elektrische Betriebsmittel (Schutzziele wurden gemäß Anhang I, Nr. 1.5.1 der Maschinenrichtlinie 2006/42/EG eingehalten). is complying with all essential requirements of the Machinery Directive2006/42/EC. In addition the partly completed machinery is in conformity with the EC Directives 2004/108/EC relating to electromagnetic compatibility and 2006/95/EC relating to electrical equipment (Protection objectives have been met in accordance with Annex I No. 1.5.1 of the Machinery Directive 2006/42/EC). Angewandte harmonisierte Normen / Harmonised Standards used EN 1493:1998+A1:2008 EN ISO 12100-1 : 2003 EN ISO 12100-2 : 2003 EN 60204-1:2006+7/2007 EN 349:1993+A1:2008 EN ISO 13850:2008 EN ISO 14121-1:2007 Fahrzeug-Hebebühnen / Vehicle lifts Sicherheit von Maschinen - Grundbegriffe / Safety of Machinery- Basic concepts Sicherheit von Maschinen - Grundbegriffe / Safety of Machinery- Basic concepts Elektrische Ausrüstung von Maschinen / Electrical equipment of machines Sicherheit von Maschinen-Mindestabstände / Safety of machinery - Minimum gaps Sicherheit von Maschinen-Not-Halt / Safety of machinery Emergency stop Sicherheit von Maschinen-Risikobeurteilung / Safety of machinery - Risk assessment Angewandte sonstige technische Normen und Spezifikationen Other technical standards and specifications used: BGG 945 Prüfung von Hebebühnen / inspection of vehicle lifts BGR 500 Betreiben von Arbeitsmitteln / management of working appliances BGV A3 Unfallverhütungsvorschrift elektrische Anlagen und Betriebsmittel / law accident prevention regulation of electric facilities and equipment Bevollmächtigter für die Zusammenstellung der relevanten technischen Unterlagen: The person authorised to compile the relevant technical documentation: Herr Pohl; Hüfinger Str. 55; 78199 Bräunlingen Ort / Place : Bräunlingen Datum / Date : 21.12.2009 Reg.-Nr. 011_2006/42/EG Carsten Rohde Geschäftsführer / Managing Director

EC Declaration of conformity for EC Machine Guide Lines 98 / 37 / EC, Appendix II A for Machine Types listed in Appendix IV Manufacturer: Rotary Lift/ Dover Corporation Address: 2700 Lanier Drive Madison (IN), 47250 USA Representative: BlitzRotary GmbH/ Dover Corporation Address: Hüfinger Straße 55 78199 Bräunlingen, Germany We declare herewith that the vehicle lift of the following detail has been designed, built and installed conforming to the current basic safety and health requirements as stated in the EC Regulations. If any alterations of the vehicle lift are made which we have not agreed to, this declaration loses its validity. Description of the vehicle lift: 4-post vehicle lift Vehicle lift type: AR40-44 capacity 4000 kg AR40-901 capacity 4000 kg AR40-902 capacity 4000 kg Machine - no.: Year of construction: Current EC - Regulations: Applied mutually agreed EN 1493+A1 Standards: EC Machine Guide Lines 98 / 37 / EC EC Guide Lines EMV 2004/108 EC EN 12100-1 u. -2; EN ISO 13857; EN 349+A1; EN 60204-1; EN ISO 13850; EN14121-1 Applied national standards and Technical Specifications: Certificate Number: Approval Body: Place: BGG945/BGR500; BGV A3 DIN 31001-1 H 9A AA3887101 DEKRA Certifications GmbH, Handwerkstr.15, 70565 Stuttgart (Notified under No.0124 to the EC Comm.) Bräunlingen, Germany Date: 2009-11-03 Signature: Carsten Rohde Managing Director

Trained Operators and Regular Maintenance Ensures Satisfactory Performance of Your Rotary Lift. Replacement Parts: See installers package for parts breakdown sheet. Order Genuine Rotary replacement parts from your nearest Authorized Parts Distributor. Maintenance Assistance: Contact your local Rotary distributor. Should further assistance be required, contact Rotary Lift, at one of the phone numbers listed below.