-------------=-=-===~-~", Speedex Owners and Parts Manual for Model 1732
FRONT END tem Description Part No. 1. 4 x 12 tire 0041-2412 2. 4 x 12 tube 0041-1412 3. 1/2 x 20 cone nut 0914-3500 4. 4x 12 rim 0041-4412 5. hub cap 0041-0102 6. axle nut 0920-4800 7. Flat washer 0085-4822 8. Bearing & Bearing race 0040-4643 10. Hub assembly 0041-8005 11. Bearing seal 0085-4822 12. 1/8 x 1112cot. pin 0052-0216 13. Drag link assy. 3602-8003 14. Steer tab weld 3603-7004 15. 1 in. spdle bushing 0040-1139 16. Front axle weld. 3603-7001 17. L.H. spindle weld. 3603-7002 18. 5/8 x 18 locknut 0903-3900 19. 5/16 x 1% spirol 0053-0613 20. R.H. spindle tab 3305-4001 21. Grease fitting 0862-0601 22. Cup point set 0849-2858 23. Front axle nut 0903-5400 24. Pitman arm weld. 3602-7004 25. Tie rod assy. 3602-8004 26. 3/4 in. shim* 0080-1042 27. 1 in. shim* 0080-1144 28. Secondary Steering shaft weld 3602-7003 29. R.H. spindle weld 3603-7003 30. Steering wheel 0044-2885 31. asa #40 x 48 P chain 0056-4024 32. 1/4 x 1% spirol 0053-0514 33. 3/16 spacer 3602-4001 34. 3/16 x 7/8 sq. key 0068-0314 35. 11T x 3/4 bore sprocket 0365-4011 36. 16T x 3/4 bore sprocket 0365-1216 37. cup point set 0876-2801 38. 3/8 lockwasher 0080-0530 39. 3/8 x 16 nut 0902-3000 40. 3/8 x 16 x 1% bolt 0847-3007 41. Main steering shaft 3602-1003 42. Steering frame weld. 3602-2001 43. 1732 frame weld 3601-7001 44. Steering output gear 0352-0724 45. Spirol pin 0053-0514
co
WRNG DAGRAM tem Description Part No. 1. 12 volt battery 0035-9943 2. Electric clutch 0035-5208 3. Engine 0030-8003 4. gnition switch 0033-9511 5. P.T.O. switch 0033-5565 6. Choke button 0036-6043 7. Throttle lever 0036-5036 8. Kill switch 0033-0650 9. Headlight assembly 0035-7001 10. Hour meter 0035-0002 11. Headlight switch 0033-5007 12. Ammeter 0035-4015 13. Headlight lens 0035-3601 14. Headlight gasket 0035-3602 15. Headlight bulb N.S. 16. Headlight bucket 0035-4231 17. Tail light Assembly 0035-0666
CLUTCH tem Description Part No. 1. 17 HP Engine 3606-0701 2. Bell housing 26-071 3. 1/4 x 1/4 x 2% key 0068-0448 4. Flywheel 3606-0702 5. Flywheel hushing 3606-4002 6. Bronze bushing 0040-1624 7. Driven pads 3606-0991 8. 3/8 Lockwasher 0080-0530 9. 3/8-24 x 3/4 bolt 0847-3103 10. Pressure plate 3606-0093 11. Throwout plate 3606-9166 12. 1/4 x 1~ Spiral pin 0053-0510 13. Fork 3606-0375 14. 1/8 x 1 cotter pin 0052-0208 15. Clutch arm 3606-7001 16. 5/16 hex nut 0902-2800 17. 5/16 lockwasher 0080-0528 18. 5/16 x 2 stud 0857-2801 19. 3/8-16 x 1 bolt 0847-3004 20. 3/8 lockwasher 0080-0530 21. Clutch housing 26-074
- _~_ r~
HYDRAULCS tem Description Part No. 1. Control lever pin 0078-0504 2.' Star nut 0907-2000 3. Shifter knob 0044-0035 4. Omco control lever 0078-1001 5. 8 hook 0078-0255 6. Omco valve 0078-8002 7. 3/8 to 3/8 90 degrees 0074-0606 8. 3/8" push lock line 69" 0077-3600 9. 1/4-3/8 push lock fitting 0076-0103 10. Tank cap 0073-0104 11. One gallon tank 0073-0491 12. Cylinder 4" stroke 0079-1840 13. 1/4" hi pressure line 30" 0081-8002 14. 1/4" hi pressure line 30" 0081-8003 15. 3/8 x 16 x 1 bolt 0847-3004 16. Pump support weldment 0078-7001 17. 3/8 to 1/4 high pressure line 70" 0081-8004 18. 3/8 to 3/8 45 degree fitting 0074-3107 19. 3/8 x 1/4 Reducer 0866-7200 20. Hydraulic pump 0078-8001 21. 3/8 x 3/8 x 45 sw. 0074-3107 22. 34" V belt A section 0391-6834 23. 5" 00 9/16 shaft pulley 0371-0950 24. 3/8 x 16 nut 0902-3000 25. 3/8 x 16 x 114bolt 0847-3005 26. Victor control lever 0078-5333 27. Victor valve 0078-8004 28. 1/4" flange 0078-7605 29. 3/8 to 3/8 push lock fitting 0076-0604 30. 3/8 lock washer 0080-0530 31. 3/8 flat washer 0080-0230
N - \ N cc / \ \
NTERMEDATE DRVE tem Description Part No. tem Description Part No. 1. Drive shaft (drive) 3611-7009 46. Right angle box lid 3611-3001 2. 1/4 x 11,1.; roll pin 0053-0510 47. 5/8 x 18 x 1 bolt 0847-3904 3. 3/8 x 16 x 11,1.; bolt 0847-3005 48. 40T Gear 3611-0240 4. 3/8 x 16 lock nut 0919-3000 49. 1/4 x 1 sq. key 0068-0416 5. 3/8 lock washer 0080-0530 50. 1/4 x 11/2 0068-0424 6. 3/8 flat washer 0080-0528 51. Right angle box 3611-0701 7. 5/16 lockwasher 0080-0528 52. L.H. foot plate weld. 3619-3001 8. Drive shaft (driven) 3611-7010 53. 3/8 female yoke 0062-3000 9. Rubber drive disc 3512-0046 54. Adjustment tab 3606-7003 10. Brake hub weldment 3611-7013 55. Clutch pedal weld. 3606-7002 11. #9 hair pin 0054-0009 56. Rubber pedal 0046-0114 12. Hand brake weldment 3610-7006 57. L.H. brake pedal weld. 3610-7002 13. Parking brake spacer 3610-2003 58. R.H. brake pedal weld. 3610-7001 14. Brake band 1710-8003 59. 5/8 shims (as needed) 0080-1042 15. Rivet 0050-1408 60. Pivot rod (clutch & brake) 3610-2001 16. Cotter pin 0052-0208 61. Pivot rod 3610-1001 17. Cotter pin 0052-0206 62. R.H. foot plate weld. 3619-3002 18. Brake knuckle 1710-7006 63. Brake push rod 3610-2002 19. Nut 5/8 x 18 NF 903-3900 64. 5/16 x 18 locknut 0919-2800 20. Washer 5/8 80-0238 65. L.H. brake pivot tab 3610-7003 21. Oil seal 0085-2391 66. R.H. brake pivot tab 3610-7003 22. Tapered roller bearing 0040-9081 67. Rubber cap 0044-0406 23. Bearing race 0040-9195 68. 5/16 x 18 x 3/4 bolt 0847-2803 24. 5/1 6 x 18 x bolt 0847-2804 69. Parking brake push rod 3611-7014 25. Brake band retainer 0444-7011 70. 3/8 x 16 nut 0902-3000 26. Grease fitting 0862-1981 71. Parking brake hdl, weld. 3611-7015 27. Seat brace weldment 3611-7011 72. 1/2 in. flat washer 0080-0234 28. R.A. box support bar 3611-2001 73. 1/2 x 13 locknut 0919-3400 29. 3/8 x 16 x 1 bolt 0847-3004 74. 3/8 x 16 x 3 bolt 0847-3012 30. 3/16 x 11/4 sq. key 0068-0320 75. 1/2 x 13 x 4 bolt 0847-3416 31. Back up ring 13/16 0040-0729 76. 1732 frame weldrnent 3601-7001 32. Bearing housing 3611-7012 77. 5/16 x 18 x 81,h 33. nput gear 0355-1314 battery bolt 0895-2836 34. 5/8 x 18 castle nut 0935-3900 78. 5/16 x 18 nut 0902-2800 35. 5/8 lockwasher 0080-0538 36. 30T gear 3611-2030 37. Tapered roller bearing 0040-7048 38. Bearing race 0040-7010 39. Back up ring 0040-7010 40. 3/8 x 16 x 3/4 bolt 0847-3033 41. Reversing box weldment 3611-7008 42. 3/8 n.p.t. plug 0866-7103 43. 15T pinion weldment 3611-7005 44. Right angle box supp. 3611-2002 45. Breather valve 0074-3650
TRANSMSSON (3 SPEED) tem Description Part No. tem Description Part No. 24. 5/1 6 x 18 x 1 bolt 0847-2804 66. Countershaft 2407-9241 25. 5/16 lockwasher 0080-0528 67. Countershaft & idler lock 2407-9226 26. 5/16 x 18 x 1~ bolt 0847-2806 68. Lockwasher 0080-0526 27. Control lever 2407-1502 69. 1/4 x 20 x 3/4 bolt 0847-2603 28. Sifter boot 0044-5941 70. 5/16 x 18 nut 0902-2800 29. Shifter knob 0044-0095 71. Lockwasher 5/16 0080-0528 30. Expansion plug 2407-9228 72. Transmission support 1707-3501 31. Control vr. support spring 2407-9243 73. Reverse idler gear 2407-9214 32. Control housing pin 2407-9224 74. 5/16 x 18 x 1 bolt 0850-2804 33. Control housing 2407-9220 75. Reverse idler gear bushing N.S. 34. Shift rail (hi & inter) 2407-9231 76. 5/16 x 18 x 1V2 bolt 0850-2806 35. Shift fork pin 2407-9225 77. Reverse idler shaft 2407-9239 36. Shift fork (hi & inter) 2407-9209 78. Control housing gasket 2407-9212 37. Shift fork (10 & rev) 2407-9210 79. Main shaft (splined) 2407-1004 38. Poppet spring 2407-9244 39. Plunger interlocker 2407-9244 40. Steel ball 2407-9201 41. Poppet spring seat 2407-9227 42. Bearing retainer 2407-0703 43. Gasket 2407-9211 44. Snap ring (main drive) 2407-9236 45. Snap ring (main gear) 2407-9237 46. Bearing (main drive) 2407-9204 47. Oil seal (front) T92-137A 48. Main drive gear 2407-1002 49. Roller bearing (13) 2407-9202 50. Shift rail (10 & rev.) 2407-9223 51. Transmission case 2407-9208 52. Gear (hi & inter) 2407-9215 53. Gear (10 & rev) 2407-9216 54. Main shaft (keyed) 2407-1001 55. Woodruff key #9 0068-0009 56. Oil retainer 2407-9136 57. Snap ring main shaft 2407-9235 58. Bearing (main drive) 2407-9203 59. Snap ring (output shaft) 2407-9238 60. Bearing (output shaft) 0040-3124 61. Bearing retainer 2407-4002 62. Oil seal 0085-7628 63. 1/2" pipe plug 0866-7102 64. Cluster gears 2407-9213 65. Countershaft bushing N.S.
,. :r-. ~ ~ 1 " t ~ f ':i '.
Final Drive tem Description Part No. 1. 1732 Frame weldment 3601-7001 2. Pinion 3611-7005 3. Tapered roller bearing 0040-7048 4. Bearing race 0040-7010 5. Back up ring 0040-5631 6. Oil seal ( 2 in.) 0085-9760 7. A.H. Brake line 3610-9001 8. R. H. strator assy. 0078-0742 9. 2 in. flat washer 3609-4001 10. R.H. brake drum assy. 309-0708 11. 13/8 in. flat washer 0080-1160 12. axle nut 0903-5400 13. Set screw 0849-2858 14. 16 in. rim 0041-4516 15. 1/2 x 20 cone nut 0914-3500 16. 8 x 16 tire 0041-2816 17. 8 x 16 innertube 0041-1816 18. 7/16 x 20 nut 0902-330 19. 7/16 lockwasher 0080-0532 20. 7/16 x 20 x 1 bolt 0847-3304 21. 1% bronze bearing 0040-1604 22. 1/4 x 2 sq. key 0068-0432 23. Drive tube weldment 3609-7003 24. 1/4 in. lockwasher 0080-0526 25. 1/4 x 20 nut 0902-2600 26. bull gear 0353-0768 S.o. 27. 13/8 in. bronze brg. 0040-1604 28. planetary gear 0354-1215 29. 5/16 x 1% spirol pin 0053-0613 30. planetary gear pin 3309-1005 31. 3/4 in. flinger 0040-2514 32. main axle 3609-7001 33. 21/4 in. flatwasher 3609-4002 34. 2 in. bronze bearing 0040-2004 35. O-ring 0045-2036 36. L.H. brake drum assy. 3309-8002 37. 2 in. snap ring 0058-0200 38. L.H. brake drum assy. 3309-8002 39. 1/4x20x 1 bolt 0847-2604 40. 1/4 in. flatwasher 0080-0226 41. Brake support weld. 3609-8002 42. Differential hsg. gear 2409-0705 43. L.H. Brake line 3610-9002 44. 1/4 x 20 x 3% bolt 0847-2613
- / r: / / \ \ \ \ ------\ '> / / / - - --7 '<...::;~'r-----l.,. \ \ 1- - - - - - - - - - \ / ~ll \ \ \ \ \ L _ / ------
TOOL LFT tem Description Part No. 1. NO.9 hair pin 0054-0009 2. 5/8 x 2 clevis pin 0051-1016 3. cylinder lift weldment 3604-7005 4. Cylinder 4 in. 0079-1840 5. 5/8 x 3 clevis pin 0051-1024 6. 1/2 x 11f.1x 13 0847-3405 7. Lift elbow bracket 3604-2001 8. 1/2 x 13 locknut 0919-3400 9. 1/2 x 212x 13 bolt 0847-3410 10. Tool link weld. (left) 3604-7002 11. Tool link weld. (right) 3604-7001 12. Rear lift weld. 3604-7004 13. Tool hitch operating bar 3604-7003 14. Third arm 3304-8004 15. 5/8 x 212clevis pin 0051-1020 16. Tow hitch weld. 3304-7002 17. 1/2 x 2 clevis pin 0051-0816 18. No. 22 hair pin 0054-0011 19. 1732 frame weldment 3601-7001
SHEET METAL & DECALS 1. 2. 3 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 2l. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31-32. 33. 34. 35. 36. 37. 38. 39. 40. 41-42. 43. 44. A. B. C. D. E. F. G. hood weldment 5/16 x 18 locknut 5/16 x 18 nut 5/16 flat washer hood spring 5/16 x 18 x 1 3/4 bolt 5/16 x 18 x 3/4 carriage bolt 5/16 lockwasher 5/16 x 18 nut 6 x 32 x 1/2 bolt #6 lockwasher #6 x 32 nut hood latch assembly wire enforced trim by ft. dash weldment drive cover fender bracket weld. (squared) l.h. square fender r.h. square fender fender brace (round) l.h. round fender r.h. round fender fender bracket weld. (round) tail light bracket 1/2 x 13 x 1 bolt 1/2 lockwasher seat spring 3/8 x 16 nut 3/8 lockwasher 3/8 x 16 x 1 1/4 bolt high back seat gas cap gas tank 3 gal. tank strap 1/4 x 20 x 3 rnd. hd. bolt 1/4 x 20 square nut 1/4 x 1 3/4 spirol pin steering wheel belt cover 1/4 x 20 x 1 bolt 1/4 lockwasher 1/4 x 20 nut fender brace (square) r.h. fender brace (square) l.h. AJ.'1ERCAN FLAG MODEL 1732 SPEEDEX (SCRPT) EAGLE WARNNG SHFT PATTERN FOOT PAD 3619-7501 0919-2800 0902-2800 0080-0228 0341-1306 0847-2807 0843-0506 0080-0528 0902-2800 0811-1512 0902-1500 0902-1500 0037-7110 3219-0601 3619-7502 3619-3501 3639-7001 3639-7501 3639-7502 3619-2502 3619-7001 3619-7002 3619-7003 3619-2006 0847-3404 0080-0534 0340-3152 0902-3000 0080-0530 0847-3005 0043-9001 0073-0103 0073-0493 0030-3501 0847-2612 0907-2600 0053-0514 0044-2885 3639-7503 0847-2604 0080-0526 0902-2600 3639-3501 3639-3502 0042-1007 0042-1732 0042-1104 0042-1110 0042-1112 0042-1101 0046-0104