TECHNICAL BID T - 3854 (E-Tender I.D. No. ) Subject : Supply of various Type of valves for GSECL UKAI TPS. Due on Date : At 3.30 P.M. (if Possible) EMD paid YES / NO EMD D. D. No. Date : OR SSI / NSIC Certification Number : Duly Notarized : YES / NO Notes : (1) The party has to submit latest and valid SSI / NSIC Certificate. Photocopy of SSI / NSIC Certificate is not acceptable. It must be duly notarized. It should not be more than 3 years old. (2) Tenders submitted without Tender Fee and Earnest Money Deposit (E.M.D.) will not be accepted. T-3854. Page 1 of 13
T 3854 Tender for Supply of various Type of valves for GSECL UKAI TPS. Sr. No. Index Page No. 1. Tender Notice 2. Undertaking (To be signed by the Tenderer) 3. Detail Specifications (Technical Bid) 4. Tender & Contract for works (Booklet) 5. Drawing Number 6. Schedule 'B' (Price Bid) Issued to Demand Draft No. for Tender Fee : & Date : Demand Draft No. for Earnest Money Deposit : & Date : IMPORTANT NOTE : This tender should be submitted duly signed without removing a single page. Otherwise the tender is liable to be rejected. For SUPPLY TENDER, TIN / PAN Number should be invariable mentioned in their technical bid otherwise your offer will be ignored and price bid will not be opened. T-3854. Page 2 of 13
Gujarat State Electricity Corporation Limited Ukai Thermal Power Station THERMAL POWER STATION, UKAI DAM, DIST - TAPI - 394680 TECHNICAL BID Reference No. : T 3854 Subject : Supply of various Type of valves for GSECL UKAI TPS. Qty. Sr. Description of Material Require Unit No. d 1 150 Class [ 2" ] Gate Valve 2 CCS Gate Valve Class-150 65NB 1 Number 3 C S Gate Valve Class-150,80 NB [ 3" ] 3 Number 4 Globe Valve-2" 1 Number 5 Cs Globe Valve Class-150,80 NB [ 3" ] 6 Gate Valve Of Size 50 Mm 1 Number 7 Cast Steel Gate Valve Size 65 Mm [ 2.1/2" ] Class 300 1 Number 8 Cast Steel Gate Valve Size 80 Mm [ 3" ]Class 300 1 Number 9 CCS Globe Valve Class 300,80 Mm NB [ 3" ] 1 Number 10 CI Gate Valve Size: 3 Inch,Class-125 3 Number 11 Cast Steel Gate Valve Size 100 Mm [ 4" ] Class 300 1 Number 12 Rising Stem, Outside Screw & Yoke type bolted bonnet type Cast Steel 3 Number GATE Valve, Size : 100 mm, Class : 150. 13 Rising Stem, Outside Screw & Yoke type bolted bonnet type Cast Steel 4 Number GATE Valve, Size : 150 mm, Class : 150. 14 Rising Stem, Outside Screw & Yoke type bolted bonnet type Cast Steel 4 Number GLOBE Valve, Size : 150 mm, Class : 150. 15 Cs Gate Valve Class 150,Size:200 Mm 16 Non Return Valve [ NRV ] 200 NB 17 Carbon Steel (ASTM A 216 GR WCB) Gate Valve, O.S., Rising 5 Number Spindle With Backseat ARRGT., Renewable Ss410 [13% Cr ] Working Parts, Flanged Ends, ASE 150 Class, Size: 50mm. 18 Gate Valve Body Cs Astm216 Cl-150,Bs1873 Nb-125 19 Cs Gate Valve Size 150 NB Raising Stem, Flanged End Connection Bolted Bonnet Class 150 20 Carbon Steel [ ASTM A 216 GR WCB ] Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 200mm. 21 Carbon Steel [ ASTM A 216 GR WCB ] Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 65mm. 22 Carbon Steel [ ASTM A 216 GR WCB ] Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 80mm. 23 Carbon Steel (ASTM A 216 GR WCB) Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 300mm. 4 Number 3 Number T-3854. Page 3 of 13
24 Non Return Valve, Size: 50mm, Body/Cover- ASTM A 351 GR CF 3 Number 8m, Swing Type Bolted Cover, Trims & Ball--Ss 316/CF 8m, Mfg Std- Bs 1868, Flanged Ends, ASA- 150 Class. 25 800 Class [ 2 " ] Globe Valve 4 Number 26 Non Return Valve (NRV) Size : 3 [ 80 MM] Bolted Hinge Type, 3 Number Class- 150, MOC of Body & Bonnet ASTM A 217 WC 6, DISC ASTM A 351 CF 8M Note: 01] While filling-up various taxes through On-line Price Bid, the party has to mention the tax in Rupees instead of percentage 02] Make for Item Sr. No.[ 1 to 16 ] : BHEL / Forbsh Marshell / Leader / Audco / KSB / Fouress / L & T/ MACNEIL MAGORE/ KBL / VR / Glando / AV / GEETA / BDK / SEMPELL / OCEN /AMCO make valves only. 03] Make for Item Sr. No.(17 to 24) & 26 : BHEL / Forbsh Marshell / Leader / Audco / KSB / Fouress / L & T/ MACNEIL MAGORE/ KBL / VR / Glando / BDK / SEMPELL / OCEN /AMCO only 04] For item sr. no. (1 to 13) & (17 to 26) : Party has to submit the material Test Certificate for the material used in the parts of the valves. Party has to submit hydro test certificates as per manufacturing standards. 05] For item sr. no.14 to 16 : Party has to submit manufacturer material test certificates showing physical & chemical properties & necessary test certificate as per relevant class & valve design standards for each valve along with the supply. 06] For item sr. no.17 to 26: Party shall have to submit I.B.R. test Certificate along with supply. 07] Party shall have to submit past order copies executed for same product at any Govt. Power plant, NTPC, State Electricity Board or NPCIL. 08] Party has to submit performance guarantee of 12 months from the date of commissioning of valves or 18 months from the date of supply whichever is earlier. 09] Manufacturers are preferable. However, if party is Authorized Dealer, party shall have to submit latest dealership certificate duly signed and stamped by the principal in their favor. Moreover, party shall have to furnish latest technical literature for the offered valves along with the technical bid. Offer without the latest Dealership certificate will be ignored. 10] Party shall have to clearly mention make of offered makes for each items in technical bid. Party will have to give full technical specification & MOC of valve parts along with Drawings /catalogue of offered valve size. 11] For item sr. no.17 to 26 : The size & make of the supplied valves should be embossed on each of the valve. 12] Party shall have to submit the performance guarantee against manufacturing defects for the period of 12 months from the date of installation or 18 months from the date of supply of material whichever is the early. 13] Test Certificate should be submitted along with supply of material. T-3854. Page 4 of 13
MATERIAL SPECIFICATION: (i) For Item Sr. No. 01 to 03 & 12. CS GATE VALVE, PRODUCT STD.BS 1414/API: 600 PRESSURE CLASS RATING - CLASS 150 BODY MATERIALS CUM STD.CCS (ASTM A216 GR WCB) PRODUCT DESCRIPTION :- BOLTED BONNET, O/S & Y TYPE, RISING STEM, TYPE OF SEAT- RENEWABLE SEAT, TYPE OF WEDGE - SOLID OR FLEXIBLE WEDGE, TRIM -SS (ASTM A276 TYPE 410 )OR its Equivalent. ENDS DETAILS- FLANGES AS PER ASME B 16.5 CL-150 R.F. TEST PRESSURE:-[1] B.T.P.30 BAR HYD. [2] S.T.P.22 BAR HYD. (ii) For Item Sr. Nos. 4 to 5 : CS GLOBE VALVE PRODUCT STD.BS 1873 PRESSURE CLASS RATING.CLASS 150 BODY MATERIALS CUM STD.CCS (ASTM A216 GR.WCB) PRODUCT DESCRIPTION- BOLTED BONNET, O/S & Y TYPE, RISING STEM, TYPE OF SEAT & DISC - RENEWABE PLUG TYPE DISC, TRIM - 13%CR. STEEL (ASTM A276 TYPE 410) OR its Equivalent. END DETAILS - FLANGES AS PER ASME B 16.5 CL.150 R.F. TEST PRESSURE.-[1] B.T.P.30 BAR HYD., [2] S.T.P.22 BAR HYD. (iii) For Item Sr. Nos. 6 to 8 & 11 : CS GATE VALVE PRODUCT STD.BS 1414/ API : 600 PRESSURE CLASS RATING: - CLASS 300 BODY MATERIALS CUM STD.CCS (ASTM A216 GR WCB) PRODUCT DESCRIPTION - BOLTED BONNET,O/S & Y TYPE,RISING STEM, TYPE OF SEAT - RENEWABLE SEAT, TYPE OF WEDGE - SOLID OR FLEXIBLE WEDGE, TRIM - SS (ASTM A276 TYPE 410 ) OR its Equivalent. ENDS DETAILS - FLANGES AS PER ASME B 16.5 CL-150 R.F. TEST PRESSURE:- [1]B.T.P.76 BAR HYD. [2] S.T.P.55 BAR HYD. (iv) For Item Sr. Nos. 09 : CS GLOBE VALVE PRODUCT:- STD.BS 1873 PRESSURE CLASS RATING.:-CLASS 300 BODY MATERIALS CUM STD.CCS (ASTM A216 GR.WCB) PRODUCT DESCRIPTION:-BOLTED BONNET,O/S & Y TYPE,RISING STEM, TYPE OF SEAT & DISC:- RENEWABE PLUG TYPE DISC, TRIM :- 13%CR.STEEL (ASTM A276 TYPE 410) OR its Equivalent. END DETAILS:- FLANGES AS PER ASME B 16.5 CL.150 R.F. TEST PRESSURE: - [1] B.T.P.76 BAR HYD. [2] S.T.P.55 BAR HYD. (v) For Item Sr. No 10: C I GATE VALVE,FLANGE END, PRESSURE CLASS RATING- CL-125 BODY MATERIAL CUM STD.CI(EN 1561 GR.JGL.200) PRODUCT DESCRIPTION- BOLTED BONNET,INSIDE SCREW,NON RISING STEM, TYPE OF DISC - RENEWABLE DISC, TYPE OF WEDGE-SOLID, TRIM :- CU-ALLOY, OR its Equivalent. GLAND PACKING- GREPHITED ASBESTOS, FASTNER- C.S.916...OR its Equivalent. GASKET - COMPRESSED ASBESTOS FIBER. END DETAILS - FLANGES AS PER ASME ANSI B 16.1,CL-125 F.F. TEST PRESSURE[1]B.T.P.20.7 BAR HYD. [2]S.T.P.15.18 BAR HYD. (vi) For Item Sr. No 13: T-3854. Page 5 of 13
BOLTED BONNET, RISING STEM, OUTSIDE SCREW & YOKE, BACKSEAT ARRANGEMENT, FLANGED ENDS TYPE, HAND WHEEL OPERATED CAST STEEL GATE VALVE. VALVE DESIGN : API 600 PRESSURE TESTING: API 598,PRESSURE CLASS RATING: - CLASS 150 PRESSURE TEMPERATURE RATING: ASME B16.34 FLANGED END DESIGN: ASME B 16.5 WITH RAISED FACE. BODY / BONNET/ COVER = ASTM A216 GR.WCB STEM/SPINDLE= A 479-410-2 / A 182 - F6a or F6a / AISI410 DISC/WEDGE: = ASTM A216 GR.WCB +13% CR or F6a / 13% Cr BODY SEAT RING = A 105 +13% CR or F6a / 13% Cr BACK SEAT= A 276-410(H) or F6a / AISI410 GLAND BUSH = A 276-410 or A182 Gr. F6a HAND WHEEL= SG IRON / CS or MALLEABLE IRON Special Note:-Party shall have to supply valves without hole drilled on Flanges. (vii) For Item Sr. No 14: [1] Description: Bolted bonnet, Rising Stem, Outside Screw & Yoke, Flanged ends type, hand wheel operated Cast Steel Globe Valve. [2] Size: 150 mm [3] Class-150 [4 ] Standards: (i) General Valve Design- BS 1873 (ii) Testing Standard: API 598; (iii) Face to Face ASME B16.10 (iv) Pressure Temperature Rating: ASME B16.34 (v) Flanged end design: ASME B 16.5 with Raised Face [5] Material specification: (a). Body & Bonnet: - ASTM A 216Gr: WCB (b). Stem:- A 479-410-2...OR..F6a / AISI410...OR...A182 Gr. F6a (c). Disc: - A 216- WCB + 13% CR...OR... F6a / 13% Cr (d). Body Seat Rings: A 105 +13% CR 6-10... OR... A 105 + Hard faced with satellite # 6...OR... F6a / 13% Cr (e). Gland Flange- A 105 (f). Gland Bush - A 276-410..OR..A182 Gr. F6a (g). Back Seat - A 276-410 H.. OR.. F6a / AISI410 (h). Bonnet Bush: - AISI 410 (i) Hand wheel: Carbon Steel/Malleable Iron (f) Hydrostatic test pressure for body=30 kg/cm2, Seat/ back seat =22kg/cm2 (viii) For Item Sr. No 15: [1] Description: Cast steel Gate valves, Class # 150 with construction outside screw, yoke type, Rising- spindle, bolted bonnet, solid wedge, integral seat ring, and wheel operated, [2] Size: 200 mm [3] Class: 150 [4] Standards: (i) Design and Mfg.Std-API-600, (ii) Inspection and Testing standard- API-598, (iii) Face to face: As per ANSI B16.10, (iv) End Connection:- Flanged as per ANSI B 16.5 RF. (v) Valve dimensions: Flange To Flange distance =295 mm Flange Thickness =30 mm Hole diameter on Flange= 20 mm Total Nos. Of Holes on flange= 08 Nos on PCD =300 mm (equally oriented on flange) [5] Material specification: (a) Body / Bonnet:-ASTM A216 Gr.WCB (b) Seat Ring: - ASTM A-216 Gr.WCB WITH 13% CR...OR.. A 105 +13% CR A 105 + Hard faced with satellite # 6...OR... F6a / 13% Cr (c) Wedge: - ASTM A -216 Gr. WCB WITH 13% Cr... OR... A 217-CA15 OR... F6a / 13% Cr (d) Stem: S.S. - AISI 410 / A 479-410-2... OR... ASTM A -216 Gr. WCB...OR..F6a / AISI410 (e) Back seat- A 276-410(H).. OR.. F6a / AISI410 (f) Hand wheel: Carbon Steel/Malleable Iron T-3854. Page 6 of 13
(g) Hydrostatic Test Pressure BODY= 30KG/CM2, SEAT/ BACK SEAT= 22KG/CM2. (ix) For Item Sr. No 16: [1] Description: Bolted cover cast steel Swing Check Valve (Non Return Valve) [2] Size: 200 mm [3] Class: 150 [4] DESIGN SPECIFICATION: (i) General Valve Design: BS 1868 (ii) Pressure Temperature Rating ASME B16.34 (iii)testing standard- API-598 (iv) Flanged end design: ASME B 16.5 (Without hole drilled on Flanges) (v) Valve Face to Face Dimensions as per ASME B16.10 & preferable dimensions of end connections are as below: Flange To Flange distance =495 mm Flange Thickness =25 mm Approximate weight: 125 Kg maximum [5] Working Pressure : Swing Check Valve size 200 mm should be fully operate at minimum working pressure: - 3 to 3.5 Kg /cm2. Hydrostatic test pressure for Shell= 30 kg/cm2, Seat leack= 22kg/cm2 [6] Standards: (a) Body & Cover: - ASTM A216 GR.WCB (b) Hinge Bracket: - IS 2062 (c) Disc: - A 216- WCB + 13% CR (d) Gasket: SS 316 + ASB SW (e) Seat ring: - A 105 +13% CR (f) Washer: - A 276-304 (g) Hinge pin: - A 276-410 (h) Disk Carrier- A 216- WCB (i) Hex Bolt- A 193-B7 (j) Stud: - A 193-B7 (k) Hex nut: - A 194-2H (l) Hex nut: - SS [18-8 ] (m) Locking plate: - SS 304 (n) Cotter pin: - A 276-304 (x) For Item Sr. No 17 To 24 & 26: CAST STEEL ASA 150 CLASS, OUTSIDE SCREW TYPE BOLTED BONNET BODY / BONNET: - ASTM A 216 Gr. WCB TRIMS: - 13 Cr / 18 Cr 8 Ni MFG STD: - API 600 INSP & TEST STD: - API 598 ENDS: - FLANGED TO ANSI B 16.5 RF (150#) HYD- TEST PRESS: - BODY: - 425 Psig (30 Kg/Cm2) SEAT: - 300 Psi (21 Kg/Cm2) Note: Item Sr. No. 18 & 19 should be having provision of water Gland sealing. (xi) For Item Sr. NO. 25 Globe valve: A. Make: KSB/AUDCO/FOURESS/VR/BDK B. Class: 600 C. valve design STD BS: 5352/I.S.O 15761 D. Pressure temperature rating ASME. B.16.34 E. Socket weld end design ASME 16.11 F. Pressure testing API-598. MATERIAL OF CONSTRUCTION 1. Body & bonnet: ASTM-A-105/425. 2. Stem: A-479-410-2. 3. Disc: ASTM-A-276.410(H). 4. Body seat ring: ST 6 INTEGRAL 5. Stem packing: Graphite 6. Hand wheel: IS-2108-BM340 7. End connections: Butt weld Type Technical specifications for Item No. 26 is to be read/ considered as NON RETURN VALVE (NRV) SIZE: 3 inch (80 MM) T-3854. Page 7 of 13
Special Notes : (1) It is mandatory for all bidders to submit their tender documents by both forms viz. online (e-tendering) and physically in schedule time. I f t ender documents submitted in only any one form, say either by on-line or physically, in that case the same tender will not be considered. Further bidders are requested to submit Price bid (Schedule-B) online only and not to submit the Price bid in Physical form. This is mandatory. If price bid is submitted in physical form, the same will not be opened and only on-line submitted Price bid will be considered for evaluation. Further, if the quantity quoted differs in the any of the technical bid forms and in price bid forms, it is at the discretion of CE Committee / ED Committee - GSECL to consider the quoted quantity. (2) Please submit photocopy of Schedule-B duly signed by you, along with TECHNICAL BID, without stating prices. (3) Tender shall not be opened without payment of EMD & Tender Fee. Please furnish details of EMD & Tender Fee paid on cover. (4) If any deviation in your offer with respect to Tender specification, then please mention clearly in separate deviation sheet, otherwise we will consider your offer is exactly as per our Enquiry / Tender specification. (5) GSECL reserves rights to place the order on technically qualified bidders for item wise / individual lowest quoted party. (6) Repeat Order : GSECL reserves right for the placement of repeat order @ 50 % of the order quantity / value within 4 (Four) months of the order as per the Clause No. 24 of Commercial Terms and Conditions instead of 25 %. Other condition of Clause No. 24 remains same. (7) It is to be noted that GSECL, Ukai TPS is establishing and implementing occupational Health & Safety Management System complying with OHSAS 18001:2007. You as a part of the GSECL Ukai team and as defined by the scope of mentioned standard, all contractors are required to comply with and participate to prevent the occupational Health and Safety hazards and risks including observation of safety rules. Further you are also to comply with all applicable legal requirements while executing the supply / work, in case the job is assigned to you. (8) Party has to accept Payment Term as per GSECL s standard terms & conditions: Payment shall be made by the GSECL for the material supplied at 80 % plus 100 % taxes against T.R.C. within 30 days and balance 20 % against S. R. Note within 45 days from the date of receipt of material at our site. (9) Delivery Period : Within 03 Months (10) While filling-up various taxes through On-line Price Bid, the party has to mention the tax in Rupees instead of percentage. (12) Tender Fee / Earnest Money Deposit (E.M.D.) / Security Deposit (S.D.) will be accepted by Demand Draft / RTGS / NEFT also. The bank details are as under, Beneficiary Name : M/s. Gujarat State Electricity Corporation Ltd. Address : Urja Nagar, GEB Colony, Taluka : Songadh. Dist. : Tapi., Pin Code - 394680. Bank Name : Bank of Baroda Ukai. Nature of A/C : Current Accounts., Branch : Ukai. Account No. : 02640200000002 IFSC CODE No. : BARB0UKAIXX ( 0 = ZERO) MICR CODE No. : 394012529. After net banking transaction, please inform to our Account Section regarding payment details along with tender number on their e-mail id of ukaisa6.gsecl@gebmail.com and ukaiao.gsecl@gebmail.com Contractor's Signature With date and seal RFQ No. : 27606 CHIEF ENGINEER (GEN.) GSECL, Ukai TPS. T-3854. Page 8 of 13
IMPORTANT : All the bidders are requested to read and verify the documents of Commercial Terms & Condition of Tender & Supply (i.e. Clause No.1 to 83) of GSECL, UKAI, TPS and confirm that all the above documents are verified & certify by you as below. I / we read the above documents and agree for the Conditions of Tender & Supply (i.e. Clause No.1 to 83) of GSECL, UKAI, TPS and accordingly submitted my / our offer. (1) For Page No. 1 to 21 of terms & condition : Party can give acceptance of clause No.1 to 83 on a single paper instead of all 21 pages. (2) For Page No. 25 to 37 : Please note that you have to furnish the details in all Annexure-1 to 13, Certificate-A & Integrity Pact i.e. dully fill, stamped and signed otherwise your offer is likely to be ignored out rightly. (3) In case of Ex-works Prices, you have to mention item wise Pkg. & Fwd., Freight, insurance charges in Annexure-10 otherwise it will be considered as per GSECL procedure for evaluation. (4) Clause No. 12 of Commercial Terms & Condition at Page No.6 of 46 : Kindly read clause No. 12 i.e. Security Deposit of Commercial terms & Condition as below. SECURITY DEPOSIT : The successful Tenderer s will be required to pay an amount equivalent to 10 % of the value of the Order (End Cost) against letter of intent as per GOG guideline as a Security Deposit for satisfactory execution of the contract. Such security deposit will be payable either in D.D./Bank Guarantees. Bank Guarantees will be acceptable if issued by Bank of Baroda and State Bank of India. The Bank Guarantees will be executed on the standard form prescribed by the GSECL. In case of the Bank Guarantees furnished / submitted, they should have clear one time validity till the completion of the order in all respects and up to the expiry of guarantee period from the date of receipt of the last consignment. Bank Guarantees for interim period will not be allowed. If by any reasons the supply period is extended then supplier should undertake to renew the Bank Guarantee at least 01 Month before the expiry of the validity failing which GSECL will be at liberty to encash the same. CORPORATE BANK GUARANTEES NOT ALLOWED. If S.D. Exemption is claimed against NSIC Certificate, then the NSIC Certificate / Competency Certificate more than 03 years old will not be considered. If the validity of the certificate expires prior to completion of the order, then it has to be got revalidated from NSIC by the Tenderer and submitted immediately; otherwise bidder shall have to arrange for payment of Security Deposit. S.D. should be paid within 07 (Seven) days after receipt of the LOI. Security Deposit is to be paid @ 6 % of the Order End Cost for Small, Cottage & tiny industrial unit of Gujarat State registered under Small Scale industries of Gujarat State and holding subsequent registration with CSPO / NSIC / DGS&D Registration Certificates for the item under tender. R.F.Q. No. : 27606 Contractor's Signature With date and seal T-3854. Page 9 of 13
PRICE BID T -3854 (E-Tender I.D. No.----------------) Subject : Supply of various Type of valves for GSECL UKAI TPS. Please submit price bid duly signed and stamp (without stating above / below rates) along with Technical Bid. T-3854. Page 10 of 13
SCHEDULE - B (Price Bid) Description : Supply of various Type of valves for GSECL UKAI TPS. Reference No. : T 3854 (E-Tender I.D. No. ) Urja RFQ No. : 27606 Sr. No. Description of materials with details of Specifications Quantity Required UOM 1 150 Class [ 2" ] Gate Valve 2 CCS Gate Valve Class-150 65NB 1 Number 3 C S Gate Valve Class-150,80 NB [ 3" ] 3 Number 4 Globe Valve-2" 1 Number 5 Cs Globe Valve Class-150,80 NB [ 3" ] 6 Gate Valve Of Size 50 Mm 1 Number 7 Cast Steel Gate Valve Size 65 Mm [ 2.1/2" ] Class 300 1 Number 8 Cast Steel Gate Valve Size 80 Mm [ 3" ]Class 300 1 Number 9 CCS Globe Valve Class 300,80 Mm NB [ 3" ] 1 Number 10 CI Gate Valve Size: 3 Inch,Class-125 3 Number 11 Cast Steel Gate Valve Size 100 Mm [ 4" ] Class 300 1 Number 12 Rising Stem, Outside Screw & Yoke type bolted 3 Number Quantity Offered by Tenderer Unit Ex- Work s In Rs. Pkg. & Fwd. Charges per Unit in Rs. Excis e Duty per unit in Rs. Sales Tax per unit in Rs. Insurance Charg es per unit in Rs. Freight Charge s per unit in Rs. Unit End Cost Price in Rs. Total End Cost Price in Rs. T-3854. Page 11 of 13
bonnet type Cast Steel GATE Valve, Size : 100 mm, Class : 150. 13 Rising Stem, Outside Screw & Yoke type bolted bonnet type Cast Steel GATE Valve, Size : 150 4 Number mm, Class : 150. 14 Rising Stem, Outside Screw & Yoke type bolted bonnet type Cast Steel GLOBE Valve, Size : 150 4 Number mm, Class : 150. 15 Cs Gate Valve Class 150,Size:200 Mm 16 Non Return Valve [ NRV ] 200 NB 17 Carbon Steel (ASTM A 216 GR WCB) Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [13% Cr ] Working Parts, Flanged Ends, ASE 150 Class, Size: 50mm. 18 Gate Valve Body Cs Astm216 Cl-150,Bs1873 Nb- 125 19 Cs Gate Valve Size 150 NB Raising Stem, Flanged End Connection Bolted Bonnet Class 150 20 Carbon Steel [ ASTM A 216 GR WCB ] Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 200mm. 21 Carbon Steel [ ASTM A 216 GR WCB ] Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 65mm. 22 Carbon Steel [ ASTM A 216 GR WCB ] Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 80mm. 5 Number 4 Number 3 Number T-3854. Page 12 of 13
23 Carbon Steel (ASTM A 216 GR WCB) Gate Valve, O.S., Rising Spindle With Backseat ARRGT., Renewable Ss410 [ 13% Cr ] Working Parts, Flanged Ends, ASA 150 Class, Size: 300mm. 24 Non Return Valve, Size: 50mm, Body/Cover- ASTM A 351 GR CF 8m, Swing Type Bolted Cover, Trims & Ball--Ss 316/CF 8m, Mfg Std- Bs 3 Number 1868, Flanged Ends, ASA- 150 Class. 25 800 Class [ 2 " ] Globe Valve 4 Number 26 Non Return Valve (NRV) Size : 3 [ 80 MM] Bolted Hinge Type, Class- 150, MOC of Body & Bonnet ASTM A 217 WC 6, DISC ASTM A 351 CF 8M 3 Number Notes : ( 1 ) The party has to refer Technical Bid for Technical Specification of above mentioned item. (2)While filling-up various taxes through On-line Price Bid, the party has to mention the tax in Rupees instead of percentage. Yours Faithfully, CHIEF ENGINEER (GEN.) (Signature of the Tenderer) GSECL, Ukai TPS. (With Company`s Round Seal) T-3854. Page 13 of 13