Benron Equipment & supply, Inc. Service Manual G5 Part Number 6-00A. and 6-00M Edition 0/008
Ez-Tex G5 Operational Instructions. Before attempting to use the G5 check material manufacturer for mixing and spraying instructions.. Check the G5 Hopper and make sure it is absolutely free from foreign debris. 3. Pull pressure regulator knob and turn counterclockwise all the way until a stop.. Select the proper spray tip for the finish you need and install onto the gun. 5. Close air valve on the gun to stop the air from flowing out. 6. Connect material hose and air hose to the G5. 7. Connect material hose and air hose to gun. 8. Mix the material you re working with. 9. Check material viscosity with funnel supplied, make sure it flows as thick as possible without lumps. 0. Pour material into hopper.. Cover the G5 with the lid supply.. Turn on your air compressor and make sure the pressure is not exceeding 00psi. 3. Connect airline to G5 air inlet connector. (A). Turn pressure regulator clockwise until material starts flowing in the hose. (A) 5. Trigger gun to purged air from hose spraying into a different bucket. 6. Open air valve to allow the material to atomize. 7. Spray on a test surface making sure you have the desired spray finish. 8. Lock pressure regulator on your setting by pushing knob to secure setting. 9. For cleaning go back to step # and flush with water, when clean insert blue ball into the hose run with water until hose is clean, if not clean repeat cleaning steps. Note: A. Always practice with clean water before supplying any material to the G5. B. Always test spray before applying on the finish surface. C. Never use material that dries in less than 30 minutes. A A
Ez-Tex G5 Micro Topping Operational Instructions. Before attempting to use the G5 check material manufacturer for mixing and spraying instructions.. Check the G5 Hopper and make sure it is absolutely free from foreign debris. 3. Pull pressure regulator knob (A) and turn counterclockwise all the way until a stop.. Connect air regulator kit p/n 5-85 to air outlet (A). 5. Connect material line adapter p/n 5-8 to material hose p/n 0-0. 6. Connect material hose adapter to the G5 material outlet (A3). 7. Connect material hose and air hose to Coltcrete gun. 8. Mix the material you re working with. 9. Check material viscosity we recommended to mix as paint viscosity, and making sure material is not draying to fast. 0. Pour material into hopper.. Cover the G5 with the lid supply.. Turn on your air compressor and make sure the pressure is not exceeding 00psi. 3. Connect airline to G5 air inlet connector (A).. Turn pressure regulator clockwise until material starts flowing in the hose. 5. Trigger gun to purged air from hose spraying into a different bucket. 6. Adjust pressure regulator (A) to allow material to flow out from the gun to a distance of 8. 7. Turn p/n 5-85 pressure regulator clockwise until material pressure at 50psi. 8. Make a spray test on a deferent working surface. 9. For final adjustment use the gun air or material knob. 0. When finish make sure to clean the sprayer immediately to eliminate material to dry in the sprayer. Note: A. Always practice with clean water before supplying any material to the G5. B. Always test spray before applying on the finish surface. C. Never use material that dries in less than 30 minutes. D. Material must be strained before use to avoid clogs in the gun. E. We recommend to use the Benron air compressor p/n 8-550 or 8-600 A A A3 A
Basic pump operations
Gun and Hose assembly Gun assembly P/N 6-3 Hose assembly P/N 3-060/G5
P/N 6-3 Gun assembly Item Part Number Description Qty 6-07 Retaining Ring 6-03 Tip 3/6" 3 6-05 Tip /" 6-06 Tip 5/6 5 6-08 Gun Body 6 6-300 Nut Guid 7 6-30 Gun Needle Assy 8 0-6 "O"-Ring 9 6-30 Fluid Control Assy 0 0-8 Needle Fitting Includes "O"-Ring 6-303 Air Fitting 7 0-0 Air valve 3 0- Sefty Clip Trigger 0-08 Gun Trigger 5 0-3 E-Ring 6 6- Trigger Pin 8 0-3 Air Fitting 9 0-30 Fluid Fitting
G5 lower assembly Air hoses plumbing: A to A 3/8 air hose B to B / air hose C to C / air hose C Note: When install pump must add clear silicon gasket to surface. 3 7 B 8 5 6 8 C 9 6 0 7 3 5 3 5 A A 8 B 8 9 Item Number 3 5 6 7 8 9 0 3 5 6 7 8 9 Part Number 3-056 6-03T 0-30 6-3 6-03 3-067T N/A 6-066T 6-6-0 9-57 6-06T N/A 3-068 8-08 3-073 6-05T 0-3 6-0 Description / Pump Pump Tee air fitting x 3/ fluid fitting quick connect 3/ x -/ Material tube / x 3/ adapter Mini regulator Mini regulator mounting nut / x / air fitting Push retainer for stud Tank base / Tee 3/8 Air fitting Nut and washer for 8-08 Safety air valve Bulkhead Connector Air fitting 3/8 air fitting / Air fitting 5/6-8 x 5/8 bolt Qty 3
G5 upper assembly 3 5 6 Item Number 3 5 6 Part Number N/A 6-6-07 6-0 6-09 -0 Description Lid Handle lock Handle 5 Gallon tank Stud Nut Qty
Note: Item #6 will mount on other side of the pump.
AIR SECTION PARTS LIST Item Part Number Description Qty 0-08 Motor Body 0-09* "O" Ring 03-08 Sleeve 0-0 Snap Ring -036 Spool 8-07 Pilot Rod 9-06* "O" Ring 0-05 Spacer 3-0* Snap Ring 9-06 Muffler Assembly 30-07* Gasket 3-09 Bolt 8 3-030* Gasket 33-033 Washer 3-03 Bolt 35-035 Valve Block 36-039 Plug 37-038* "O" Ring 38-037* Packing "U" Cup 39-00* Packing "U" Cup 0-03* Valve Insert -03* Valve Plate -0 Washer 3-03 Plate Note: -05 Air Motor Repair Kit ( Includes All Parts Marked With * ) FLUID SECTION PARTS LIST Item Part Number Description Qty -006 Rod -00 "O" Ring 5-005 Washer 6-008 Diaphragm Nut 7-007 Diaphragm 5-009 Fluid Cap 9-06 "O" Ring -09 Insert 6-09 Bolt 8-07 Sleeve -08 Duckbill 6-05 Manifold 6-00 Flange Nut 63-0 Plug 6-09 Stud 8
Rotortex Warranty G5 Warranty All products manufactured by Benron Equipment & Supply, Inc. are warranted to the original purchaser against defects in material and workmanship at the time of sale by an authorized Benron Equipment & Supply distributor and for a period of months from date of purchase. This warranty applies only if the product is operated and maintained in accordance with Benron s written instructions. Benron will repair or replace any part of the equipment proven defective. Repair or replacement under this warranty shall be the purchaser s sole remedy for breach of this warranty. Benron Equipment and Supply will not be responsible for any downtime resulting from breakdown or for cost of rental equipment while repairs are being made. This warranty does not cover damage to the product resulting from improper use, accident, user s negligence, or if the product has not been operated or installed in accordance with Benron s recommendations. This warranty does not cover damages caused by service or repair performed by other than a Benron authorized repair center. Benron is not liable for incidental or consequential damages or to damages to other properties caused by use of the product in a faulty condition or manner. Any implied warranty of merchantability or fitness for a particular purpose is limited to 90 days for professional rental use, and for One year ( months) for professional contractor use, from date of purchase. Some states do not allow limitations on how long implied warranty lasts so above limitations may not apply to you. If product is defective in material or workmanship during the warranty period, return it with proof of purchase to Benron Equipment & Supply, Inc. or to Benron authorized warranty service center, for verification of claimed defect. If the alleged defect is verified, Benron will repair or replace (at Benron s option) any defective parts, and will return the product, transportation prepaid. If no defects in material or workmanship are found, Benron will repair the product at a reasonable charge. Charges may include the cost of parts, labor, and freight. Two One year limited warranty, excluding consumable components. The items, which are not covered, are: Spray tips, Gun needle, Rotor Guns packing and Stator, kit, ball valves, Material hose, Air hose and control cords. This warranty does not cover damage or defects caused by or related to Abrasion, Corrosion, Abuse, Misuse, Negligence, Accident, Normal wear, Faulty Installation or tampering in manner which impairs normal operation. All warrantee clime on the Honda engine will process by only Honda authorize repair center only with prove of purchase of the original receipt. Benron equipment & Supply, Inc. 583 Stagg Street Van Nuys, CA 906 In USA Call: (888) EASY-TEX (888 37-9839) In California Call: (88) 787-55 Fax: (88) 787-8866