Series 1200 Hydraulic Speed Reducer The rugged construction and versatility of the Series 1200 Speed Reducer is ideal for stationary & mobile applications where slow speed, high torque, or variable speed and reversing are needed. pplications include paving and curb forming, ditching, irrigation and plastic and extruding equipment. vailable with a oil cooled adjustable automatic safety brake. Up To 24,000 Inch Pounds of Output Torque Series 1200 shown with right hand output shaft Powerful Compact fficient loom TM Hydraulic Speed Reducers Standard Features GR CS WORM SHFT WORM GR GR RTIO RINGS OUTPUT SHFT MOTOR MOUNT RK OPTION - Made of high strength cast iron. Completely sealed for oil enclosed operation and to keep dirt out. - One piece alloy steel hardened and ground to insure long service. The hydraulic motor couples direct to the shaft. - High tensile aluminum-nickel alloy bronze. Optimum lead and pressure angles transmit maximum power to the drum. - 20:1 standard, optional 27:1 and 40:1 ratios provide optimum efficiency in power and speed. - Worm gear and worm shaft run on tapered roller bearings in an oil enclosed gear case - 1-1/2 diameter heat -treated alloy steel minimum tensile strength 150,000 psi. - S () 2 bolt flange mount-standard. - Single direction oil cooled adjustable automatic safety brake. RV11/2003
Series 1200 Model Selection from Performance Data 1910 MODL XMPL: 12---SR-RH-20-LP Gear Case and Shaft Designation 12 = Series 1200 with 1-1/2 Output Shaft only Optional Low Profile Mounting Oil Cooled utomatic Safety rake Hydraulic Motor Designation,, C, DD,, G, 4.9, 6.2, 8.0, 9.6, 11.9 N - No Motor IS - Input Shaft Gear Ratios 20:1, 27:1, 40:1 Shaft Position RH - Right Hand LH - Left Hand 10:1 Not vailable Speed Reducer
Series 1200 loom Hydraulic Speed Reducers With Hydraulic Safety rake Model Selection from Performance Data 1910 PULL 1ST LYR OF CL (LS.) 10000 8000 6000 4000 2000 0 500 1000 11.9 9.6 8.0 6.2 G DD C 4.9 20:1 RTIO (standard) CL SPD 1ST LYR (FT./MIN.) 60 50 40 30 20 1500 2000 2500 3000 0 OIL PRSSUR (LS./SQ.IN.) 10 4.9 6.2 8.0 C DD 9.6 G 11.9 5 10 15 20 25 OIL FLOW (GLLONS/MIN.) PULL 1ST LYR OF CL (LS.) 12000 10000 8000 6000 4000 2000 0 500 1000 27:1 RTIO (optional) 40 11.9 8.0 6.2 9.6 DD 30 4.9 6.2 4.9 G C C 8.0 20 DD 9.6 G 11.9 10 1500 2000 2500 3000 0 5 10 15 20 25 OIL PRSSUR (LS./SQ.IN.) CL SPD 1ST LYR (FT./MIN.) OIL FLOW (GLLONS/MIN.) PULL 1ST LYR OF CL (LS.) 10000 8000 6000 4000 2000 0 500 1000 40:1 RTIO (optional) 30 6.2 4.9 8.0 DD 20 C 10 1500 2000 2500 3000 0 OIL PRSSUR (LS./SQ.IN.) CL SPD 1ST LYR (FT./MIN.) C 4.9 6.2 8.0 DD 5 10 15 20 25 OIL FLOW (GLLONS/MIN.)
Dimensional Drawings Series 1200 Speed Reducer 1910 2.75 OPTIONL ND CP COVR FOR LSS RK OPTIONL Ø2-13UNC 1 (4) HOLS 1.50 6.00 5.13 9.19 Ø1.50 5.56 OUTPUT SHFT W/.375-.376 KYWY 5.00 9.45 13.89 5.25 STNDRD RIGHT HND Ø1.50 OUPUT SHFT.375-.376 KYWY OPTIONL Ø1/2-13UNC x.75 DP (3) HOLS ON Ø5.00.C. QULLY SPCD PRT MOUNTING HOLS ND FCD 4.75 2.37 2.37 LFT HND SHOWN 0.63 4.00 MOTOR DSIGNTION DIMNSION 19.11 19.26 C 19.38 DD 19.51 19.73 G 4.9 19.86 21.15 6.2 21.33 8.0 21.58 9.6 21.58 11.9 21.85
1200 SRIS MODL SLCTION MOTOR 12--SR MOTOR 12--SR C MOTOR 12-C-SR DD MOTOR 12-DD-SR MOTOR 12--SR G MOTOR 12-G-SR 4.9 MOTOR 12-4.9-SR 6.2 MOTOR 12-6.2-SR 8.0 MOTOR 12-8.0-SR 9.6 MOTOR 12-9.6-SR 11.9 MOTOR 12-11.9-SR INPUT SHFT MODL 12-IS-SR
Correct choice of Directional Control Valves for loom Winches Tandem Center Spool Valve Work Ports are blocked in neutral position Use on all winches that use motor only to hold load. *Winches require ridged mounting plate. See owner s manual for information about proper mounting plate thickness or call loom Sales ngineer at factory WRNING! Goods are not intended for use in the moving or lifting of persons! The winches described herein are neither designed nor intended for use or application to equipment used in the lifting or moving of persons and it is understood that all such use shall be at the sole risk of the user. The cable clamps on winches are not designed to hold rated loads. minimum of 5 wraps of cable must be left on drum barrel to guarantee holding of rated load. pplications of winch where life would be endangered by any event are not recommended. www.bloommfg.com LOOM Manufacturing Inc. Winch Division 1443 220 th Street,, Independence, Iowa 50644 FX 319-827-1140 PHON 319-827-1139 Copyright 2015 loom Mfg. Inc.