Pneumatic Grips MNC/10-100 WEDGE type MNC Series Pneumatic Type Wedge Grips Movement centered with high pre-load Versions with capacities 10, 20, 50, 100kN To perform tensile tests on plastics, aluminum, steel, composite materials such as epoxy resin with reinforced fiberglass. Principle: a large pneumatic piston moves the wedge jaws against the test sample. Due to the action of the tensile on the specimen during the test, the clamping force is reinforced even more The clamping force is approx. 3 to 5 times higher than the tensile force. Thus, the samples can be maintained very well with low coefficient-friction. MNC-100-Ni-T250 If necessary, clamping pressure is possible with the help of a laboratory compressor to increase (UN216) to 16 Bar Pneumatic wedge action grips. Ideal for testing elastomers, plastics, fiberglass sheets and films inside a thermal chamber (+180 C +280 C) Each grip has a double acting jaw that faces that movement to the center line of the sample by means of air pressure, ensuring the correct alignment of the samples. Page 1 of 9
MNC/10-10kN Stainless steel pneumatic wedge type grips - Holding force 5 kn (without load), maintaining force and increasing to 20 kn, with a load of 10 kn optimal for use in chambers up to +280 C MNC/10-Af159+R200 10kN Adapter made of stainless steel 200 mm long 58 With a pneumatic connection on the end of the tube ideal for use in a temperature chamber MNC/10-Af159 Page 2 of 9
MNC/10-Af159-Rxxx With long adapter for use with temperature chambers MNC/10 With internal tube of compressed air to activate the pneumatic pistons using temperature test chamber MNC/10-Af159+R114+R425 Page 3 of 9
MNC/10-BD Diamond jaws of 30 x 40 mm, For sample thicknesses of 0-6 mm Diamond mandibles for testing hard sheets MNC/10 Page 4 of 9
MNC/20 20kN Pneumatic Grips Wedge type of 20kN MNC/20-BP8 0-8 mm MNC/20-BV8 3-8 mm MNC/20-BP15 7-15 mm MNC/20-BV13 7-13 mm MNC/50 50kN Pneumatic Grips Wedge type of 50kN MNC/20-318 Page 5 of 9
MNC/100 100kN The clamping force without applying traction is 56 kn (at 7 Bar), using the UN216 air compressor (at 15 Bar) increases up to 120 kn of tension holding force, and applying a traction of 50 kn is 133 kn (at 7 Bar) The clamping force of the MNC / 100 without applying traction is 56 kn (at 7 bar). The wedge effect on the clamping force increases to 210 kn when a tensile load of 100 kn is applied. MNC/100-Af50-Ni-T250 C Superfícies niqueladas con adaptador especial para usar las mordazas dentro de una cámara para ensayos a diferentes temperaturas. MNC/100-Af318+BW Page 6 of 9
MNC/100-V12 D= 4-12 mm de Ø MNC/100-BP12 S= 0-12 mm MNC/100-V22 D= 12-22 mm de Ø MNC/100-BP22 S= 10-22 mm Page 7 of 9
MNC/100-D260-S46 Special version Opening 46 mm MNC/100-BP12 MNC/100-BP36 4-16 mm 24-36 mm MNC/100-BP12 4-16 mm MNC/100-BP36 24-36 mm MNC/100-D260-S46-M48-T180 Page 8 of 9
General information For all versions of the MNC series it is possible to produce jaws for round specimens BV, For very small round specimens (for example up to 5 mm in diameter we propose to use the BP flat jaws. T180 T280 For Temperatures between -70ºC y +180 C con sellante Vitón For Temperatues to +280 C It is possible with special Teflon sealant. Accessories Pneumatic pedals - Valves - Tubes - Connections Silent air compressor suitable for Laboratories - Max. pressure: 16 bar; - Noise level: 45dB (A) - Motor: 0,13 KW - Voltage: 230 V - Frecuency: 50 Hz - Displacement: 17 l/min - Tank size: 3,5 l - With Pressure Reducer - Dimensions: 340 x 290 x 340 mm (L x W x H) - Weght: 18 kg All specifications subject to possible changes without prior notice Page 9 of 9