All good things come from above VH and VHF power supply units for power and compressed air THINK CONNECTED.
VH and VHF power supply units 2 OBO EGS
All good things come from above Supply units for power and compressed air Often, supplying power to workstations in production and workshops is a difficult matter. The required power sources, such as heavy current and compressed air, come from central supply points, are run to the individual workstations and must then often be re-bundled. These supply lines are often easily missed and pose additional risks at the workstation. Besides posing the risk of tripping, carelessly routed compressed-air hoses or power cable extensions often cause transport problems and are sources of risk not to be underestimated, especially when rapid working routes are required. OBO Bettermann can provide assistance here: With the space-saving type VH and VHF power supply units, problematic extension cables and hoses are a thing of the past. The solution is literally in the air and close at hand! The required compact, box-like distributors can be suspended from the ceiling using a knotted chain and thus freely positioned in the room. Thus OBO power supply units offer safe, rational working at the workstation. EGS OBO 3
VH power supply units for use in normal working environments VH power supply unit Under normal working conditions, the VH distributor is used for machining and mounting areas or in car workshops. To meet the necessary requirements, besides the freely equippable power supply units for four or eight devices, there is also a range of pre-equipped and prewired units available. 4 OBO EGS
VHF power supply units for use in moist and wet areas VHF power supply unit In work areas such as bakeries, industrial kitchens, abattoirs or laboratories, power supplies will be subjected to special requirements. This is a job for the VHF distributor. It allows a wide range of solutions, which are suitable for damp and wet areas up to a protection rating of IP44. The right accessories for every application A comprehensive range of accessories complete the VH and VHF power supply units. It allows the installation of Modul 45 accessories, standard switching and connection devices, extension sockets with 38 x 38 mm fastening system, CEE connection units, protection units and much more. This means that there are no limits to the range of applications for power supply units. Heavy current, compressed air, data technology and even country-specific installation solutions are available wherever they are required. EGS OBO 5
Mounting aid for power supply units VH and VHF Installation with knotted chain Mounting with a knotted chain is a rigid installation and does not require any additional cable reserves. Shorten the knotted chain to the required length and fasten it using the pre-mounted eyelet on the housing cover. Installation with tension spring With additional installations with a tension spring, always ensure flexible cable routing. The tension spring is usually used with compressed air for VH units and inserted directly in the fastening seat. Compressed air connection The compressed air connection is designed for compressed air hoses 3 x 3.5 mm. The hose connection is fixed and locked using a hose clip. Cable entry Cables are inserted using the pre-punched openings in the housing cover. Correct strain relief is achieved using the cable terminals integrated in the housing. VH device installation Modul 45 The Modul 45 devices are inserted and locked into the appropriate cover plate. After connecting the cable, place the cover plate on the housing and fix it using two screws. VH device installation support ring (EKR) After cable connection, accessories with a support ring are screwed directly into the housing. The cover plate is fastened by mounting the central plate. VH / VHF device installation expansion devices Fasten extension accessories for the 38 x 38 mm fastening system to the appropriate cover plate using the screws supplied. After connecting the cable, place the cover plate on the housing and fix it using fastening screws. VH / VHF device installation CEE The connection of cables to a CEE connection unit must be carried out using a pre-mounted cover plate. During device mounting, the cover plate is fastened using four fastening screws. VHF device installation power supply unit In the first step, the appropriate support is premounted using a PE terminal strip or N and PE terminal strip in the upper half of the housing. For this, the inner part of the fastening tracks must be completely removed. 6 OBO EGS
VHF device installation power supply unit In the second step, the support bracket for the power supply unit is mounted in the lower half of the housing. Then the devices are connected and installed. VHF device installation power supply unit In the third step, the transparent cover is placed on the cover plate and fastened with four screws. After that, mount the cover plate onto the equipped housing side using four screws. EGS OBO 7
8 OBO EGS
Industrial and special connector systems VH-4 power supply units, IP20 Without compressed air connection With compressed air connection VH-8 power supply units, IP20 Without compressed air connection With compressed air connection VH accessories VH sockets VH-4 power supply units, IP20, white Tensioning spring Knotted chain Partition Cover plate Balancer for VH Protective contact socket International sockets CEE connection unit Empty housing without cover plates Cover plates, white VHF-8 power supply unit, IP44 Without compressed air connection With compressed air connection VHF accessories VHF sockets Tensioning spring Knotted chain Partition Cover plate Protective equipment installation Protective contact socket CEE connection unit EGS OBO 9
VH power supply units, IP20 VH-4 power supply unit, empty housing VH-4 LG Graphite black 6,700 Empty housing with suspension lug and grip hook, for the installation of four electrical resources, with included partition. Without cover plates. 609 80 0 VH-4 power supply unit, 4x protective contact socket VH-4 4SD Graphite black 95,000 Housing equipped and pre-wired with suspension lug, grip hook and four cover plates. 609 80 2 Equipped as follows: 4 x single protective contact sockets 6 A/250 V with increased touch protection, pre-wired for two AC currents, connection via 2 x 3-pin terminals, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, 3x protective contact socket, x CEE 6 A VH-4 3SDC6 Graphite black 5,700 Housing equipped and pre-wired with suspension lug, grip hook and four cover plates. 609 80 4 Equipped as follows: 3 x single protective contact sockets 6 A/250 V with increased touch protection, pre-wired for an AC current, connection via x 3-pin terminal, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, 4x earthing pin socket VH-4 4SF Graphite black 95,000 Housing equipped and pre-wired with suspension lug, grip hook and four cover plates. 609 80 6 Equipped as follows: 4 x single sockets with earthing pin 6 A/250 V with increased touch protection, pre-wired for two AC currents, connection via 2 x 3-pin terminals, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, 3x earthing pin socket, x CEE 6 A VH-4 3SFC6 Graphite black 5,700 Housing equipped and pre-wired with suspension lug, grip hook and four cover plates. 609 80 8 Equipped as follows: 3 x single sockets with earthing pin 6 A/250 V with increased touch protection, pre-wired for an AC current, connection via x 3-pin terminal, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, empty housing, with compressed air connection VH-4L LG Graphite black 343,800 609 8 0 Empty housing with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2- way distributor /2". With suspension lug and grip hook, for the installation of four electrical resources, with included partition. Without cover plates. 0 OBO EGS
VH power supply units, IP20 VH-4 power supply unit, 4x protective contact socket, with compressed air connection VH-4L 4SD Graphite black 428,600 609 8 2 Housing equipped and pre-wired, with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2-way distributor /2", with suspension lug, grip hook and four cover plates. Equipped as follows: 4 x single protective contact sockets 6 A/250 V with increased touch protection, pre-wired for two AC currents, connection via 2 x 3-pin terminals, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, 3x protective contact socket, x CEE 6 A, with compressed air connection VH-4L 3SDC6 Graphite black 380,000 609 8 4 Housing equipped and pre-wired, with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2-way distributor /2", with suspension lug, grip hook and four cover plates. Equipped as follows: 3 x single protective contact sockets 6 A/250 V with increased touch protection, pre-wired for an AC current, connection via x 3-pin terminal, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, 4x earthing pin socket, with compressed air connection VH-4L 4SF Graphite black 428,600 609 8 6 Housing equipped and pre-wired, with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2-way distributor /2", with suspension lug, grip hook and four cover plates. Equipped as follows: 4 x single sockets with earthing pin 6 A/250 V with increased touch protection, pre-wired for two AC currents, connection via 2 x 3-pin terminals, x CEE socket 6 A/45 V, with partition for circuit separation. VH-4 power supply unit, 3x earthing pin socket, x CEE 6 A, with compressed air connection VH-4L 3SFC6 Graphite black 440,000 609 8 8 Housing equipped and pre-wired, with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2-way distributor /2", with suspension lug, grip hook and four cover plates. Equipped as follows: 3 x single sockets with earthing pin 6 A/250 V with increased touch protection, pre-wired for an AC current, connection via x 3-pin terminal, x CEE socket 6 A/45 V, with partition for circuit separation. VH-8 LG Graphite black 88,200 Empty housing with suspension lug and grip hook, for the installation of eight electrical resources, with included partition. Without cover plates. VH-8 LG8P2 Graphite black VH-8 power supply unit, empty housing 609 82 VH-8 power supply unit, empty housing, with cover plates 23,400 609 82 0 Empty housing with suspension lug and grip hook, for the installation of eight electrical resources, with included partition. With eight cover plates for accessories with concealed support ring or support bracket. EGS OBO
VH power supply units, IP20 VH-8 power supply unit, empty housing, with compressed air connection VH-8L LG Graphite black 300,000 609 82 5 Empty housing with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2- way distributor /2". With suspension lug and grip hook, for the installation of electrical resources, with included partition. Without cover plates. Tension spring VH/VHF L VH-F00VA 3,000 609 82 9 40 V2A Stainless steel, grade 30 Tension spring for VH/VHF power supply units, with German eyelet. Fmax.= 00 N L0 = 200 mm Ln = 500 mm (for Fmax.) Material: VA ø 3.0 mm Knotted chain Designation VH-K800 sold by the metre m kg/00 m 20,000 609 87 0 St Steel /m Knotted chain made of pre-copper-plated steel, nickel-plated, according to DIN 5686. Max. tensile force: 800 N. Note: Specify the required chain length during ordering. Balancer for VH up to.5 kg loads 93 42 93 VH-BAL.5 SW 40,500 Balancer with an adjustable load of 0.5 to.5 kg, maximum cable extension 0.9 m. 609 88 3 48 Balancer for VH up to 2.5 kg loads 93 VH-BAL2.5 SW 40,500 Balancer with an adjustable load of.5 to 2.5 kg, maximum cable extension 0.9 m. Partition VH-4 VH-4 TW Graphite black 2,350 609 88 5 609 83 2 PVC Polyvinylchloride Additional partition wall for reciprocal insulation of three different power circuits and types. Version for VH-4. 42 93 48 2 OBO EGS
VH power supply units, IP20 Partition VH-8 VH-8 TW Graphite black PVC Polyvinylchloride 4,890 609 86 2 Additional partition wall for reciprocal insulation of three different power circuits and types. Version for VH-8. Cover plate VH, for EK and EKR devices VH-P2 Rape yellow 2,300 609 83 4 Cover plate with opening Ø 45 mm for the installation of a device with concealed support ring or support clamp. Cover plate VH, for Modul 45 devices, single VH-P4 Rape yellow 2,030 609 84 0 Cover plate to install a single Modul 45 socket. Cover plate VH, for Modul 45 devices, double VH-P5 Rape yellow,830 609 83 6 Cover plate to install a double Modul 45 socket. VH-P7 Rape yellow Cover plate VH, for x extension socket, type ASD,890 609 83 9 Cover plate with opening for the installation of a socket with 38 x 38 mm fastening system. VH-P3 Rape yellow,870 609 83 8 Cover plate with a Ø 70 mm opening for the installation of a CEE socket 6/32 A with 60 mm fastening track, including four fastening screws. Information on equipment: Max. 2 CEE sockets 6/32 A in a power supply unit VH-4 Max. 4 CEE sockets 6/32 A in a power supply unit VH-8 Cover plate VH, for CEE connection unit EGS OBO 3
VH power supply units, IP20 VH cover plate as blanking cover VH-P Rape yellow 3,000 609 84 2 Cover plate as blanking cover. Socket 0, protective contact, single STD-D0 RW Pure white PC Polycarbonate 4,200 620 00 8 Power socket single 0, with increased touch protection with screwless terminals, 2-pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Socket 33, protective contact, double STD-D3 RW2 Pure white 7,800 620 0 2 PC Polycarbonate Protective contact socket double 33, with increased touch protection, with screwless terminals, 2-pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Socket 0, with earthing pin, single STD-F0 RW Pure white 4,000 620 5 2 PC Polycarbonate Socket with earthing pin single 0, with increased touch protection with screwless terminals, 2- pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Socket 33, with earthing pin, double STD-F3 RW2 Pure white 7,500 620 24 2 PC Polycarbonate Socket with earthing pin double 33, with increased touch protection with screwless terminals, 2-pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Socket 0, British Standard, single STD-BS0 RW Pure white 4,000 620 72 2 Socket, single 0, British Standard, conforming to BS 363, with increased touch protection, with screw terminals, 2-pin, 3 A, 250 V~. 45 45 33,20 4 OBO EGS
VH power supply units, IP20 Socket 0, Switzerland, single SKS-CH0 RW Pure white PC Polycarbonate 3,400 67 20 0 Socket, single 0, to Swiss standard (SEV), with screwless terminals, 2-pin, 0 A, 250 V~, type 3, with connection terminals to IEC 60884-. Socket 0, Denmark, single SKS-DK0 RW Pure white PC Polycarbonate 20 3,050 67 20 2 Socket, single 0, to Danish standard, with increased touch protection, with screw terminals, 2- pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Socket 0, India, 6 A, single STD-IN0 RW Pure white 4,300 620 72 6 Socket, single 0, India, conforming to BS 546, with increased touch protection, with screw terminals, 2-pin, 5 A, 250 V~. Socket 0, South Africa/India, 6 A, single STD-SA0 RW Pure white 5,000 620 73 0 Socket, single 0, South Africa/India, conforming to BS 546, with increased touch protection, with screw terminals, 2-pin, 6 A, 250 V~. 45 45 45 35 45 35 50 39 50 STD-CN0A0 RW Pure white Socket 0, China, 0 A, single 4,000 Socket, single 0, China, with increased touch protection, with screw terminals, 2-pin, 0 A, 250 V~. STD-CN0A6 RW Pure white 4,00 Socket, single 0, China, with increased touch protection, with screw terminals, 2-pin, 6 A, 250 V~. ASD-D0 SW prot. contact w. hinged cov. Black 620 74 0 Socket 0, China, 6 A, single 620 74 2 Surface-mounted socket 0 with hinged cover, protective contact, single Designation,000 609 87 3 Protective contact extension socket 0 with hinged cover, with screwless terminals, 2-pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Protection rating: IP 44. EGS OBO 5
VH power supply units, IP20 CEE connection unit, 6 A CEE-6A CEE socket with 60 mm fastening track, 3-pin + N + PE, 400 V, 6 A, 6 h. 9,00 609 87 4 CEE connection unit, 32 A CEE-32A CEE socket with 60 mm fastening track, 3-pin + N + PE, 400 V, 32 A, 6 h. 20,400 609 87 6 6 OBO EGS
Power supply unit VH, pure white, IP20 VH-4 power supply unit, empty housing VH-4 LG RW Pure white 72,000 Empty housing with suspension lug and grip hook, for the installation of four electrical resources, with included partition. Without cover plates. 609 80 Cover plate VH, for Modul 45 devices, single VH-P4 RW Pure white 2,000 609 84 Cover plate to install a single Modul 45 socket. Cover plate VH, for Modul 45 devices, double VH-P5 RW Pure white,830 609 83 5 Cover plate to install a double Modul 45 socket. Cover plate VH, for CEE connection unit VH-P3 RW Pure white 2,000 609 83 7 Cover plate with a Ø 70 mm opening for the installation of a CEE socket 6/32 A with 60 mm fastening track, including four fastening screws. Information on equipment: Max. 2 CEE sockets 6/32 A in a power supply unit VH-4 Max. 4 CEE sockets 6/32 A in a power supply unit VH-8 VH-P RW Pure white Cover plate as blanking cover. VH cover plate as blanking cover 3,000 609 84 3 EGS OBO 7
VHF power supply units, IP44 VH-8 power supply unit, empty housing VHF-8 LG Graphite black 05,000 609 82 2 Empty housing with suspension lug and grip hook, for the installation of electrical resources, with included partition. Without cover plates to supply workplaces in wet areas. Protection rating: IP 44. VH-8 power supply unit, empty housing, with compressed air connection VHF-8L LG Graphite black 400,000 609 82 7 Empty housing with m pipe /2" and connection for compressed air hose 3 x 3.5 mm and 2- way distributor /2". With suspension lug and grip hook, for the installation of electrical resources, with included partition. Without cover plates to supply workplaces in wet areas. Protection rating: IP 44. Tension spring VH/VHF L VH-F00VA 3,000 609 82 9 40 V2A Stainless steel, grade 30 Tension spring for VH/VHF power supply units, with German eyelet. Fmax.= 00 N L0 = 200 mm Ln = 500 mm (for Fmax.) Material: VA ø 3.0 mm Knotted chain Designation VH-K800 sold by the metre m kg/00 m 20,000 609 87 0 St Steel /m Knotted chain made of pre-copper-plated steel, nickel-plated, according to DIN 5686. Max. tensile force: 800 N. Note: Specify the required chain length during ordering. Balancer for VH up to.5 kg loads 93 VH-BAL.5 SW 40,500 Balancer with an adjustable load of 0.5 to.5 kg, maximum cable extension 0.9 m. VH-BAL2.5 SW 40,500 Balancer with an adjustable load of.5 to 2.5 kg, maximum cable extension 0.9 m. 609 88 3 609 88 5 42 93 Balancer for VH up to 2.5 kg loads 93 42 93 48 48 8 OBO EGS
VHF power supply units, IP44 Partition VHF, without compressed air connection VHF-TW Graphite black 3,520 609 86 0 PVC Polyvinylchloride Additional partition wall for reciprocal insulation of three different power circuits and types. Partition VHF, with compressed air connection VHF-TW L Graphite black 3,900 609 86 PVC Polyvinylchloride Additional partition wall for reciprocal insulation of three different power circuits and types. Cover plate VHF as blanking cover VHF-P Rape yellow 7,000 609 86 8 PVC Polyvinylchloride Cover plate as blanking cover. Cover plate VHF x with fast. system VHF-P7 Rape yellow 6,600 609 87 8 PVC Polyvinylchloride Cover plate with opening for the installation of a socket with 38 x 38 mm fastening system. 45 04,50 38 38 59,50 VHF-P2 Rape yellow PVC Polyvinylchloride Cover plate VHF, for x surface-mounted socket, type ASD 7,400 Cover plate with a Ø 45-mm opening for the installation of an extension socket (type ASD-...) with 38 mm fastening track, including 4 screws for fastening the device. VHF-P8 Rape yellow PVC Polyvinylchloride 5,900 609 85 6 Cover plate VHF, for 2x surface-mounted socket, type ASD 609 87 9 Cover plate with two Ø 45 mm openings for the installation of two extension sockets (type ASD-...) with 38 mm fastening track, including 8 screws for fastening the device. VHF-P3 Rape yellow PVC Polyvinylchloride 7,000 Cover plate VHF, for CEE connection unit 609 86 5 Cover plate with a Ø 70 mm opening for the installation of x CEE socket 6/32 A with 60 mm fastening track, including 4 screws for fastening the device. EGS OBO 9
VHF power supply units, IP44 Cover plate VHF, for x surface-mounted socket, type ASD and x CEE connection 45 04,50 38 38 VHF-P3 Rape yellow 7,400 609 85 8 80 60 60 60 59,50 PVC Polyvinylchloride Cover plate with a Ø 45 mm opening for the installation of one extension socket (type ASD-...) with 38 mm fastening track and a Ø 60 mm opening for the installation of one CEE socket 6/32 A with 60 mm fastening track, including 8 screws for fastening the device. Cover plate VHF for protective equipment installation VHF-P6 Rape yellow 4,700 609 86 7 PVC Polyvinylchloride Cover plate with cut out for the installation of a cover above protection unit (type VHF-AE4TE). Maximum equipment corresponds to four units. Cover plate for the VHF power supply units for the installation of a cover above protection unit (type VHF-AE4TE). Maximum equipment corresponds to four units. VHF protective unit construction, cover and support clamp VHF-AE4TE 2,800 609 85 0 Cover and support clamp for the installation of protective equipment such as miniature circuit breakers or FI protection switches to max. four units. Note: Use only in conjunction with the supports VHF-T or VHF-T2. VHF protective unit construction, support with PE terminal strip VHF-T 6,730 St Steel Support with PE terminal strip for installation of FI protection switches, consisting of: - Base element with hat rail 35 mm and PE terminal strip 4 x 0 mm² - Fastening material 609 85 2 VHF protective unit construction, support with N + PE terminal strip VHF-T2 8,380 609 85 4 St Steel Support with N and PE terminal strip for installation of miniature circuit breakers, consisting of: - Base element with hat rail 35 mm, N terminal strip 4 x 0 mm² and PE terminal strip 4 x 0 mm² - Fastening material Surface-mounted socket 0 with hinged cover, protective contact, single Designation ASD-D0 SW prot. contact w. hinged cov. Black,000 609 87 3 Protective contact extension socket 0 with hinged cover, with screwless terminals, 2-pin, 6 A, 250 V~, with connection terminals to IEC 60884-. Protection rating: IP 44. 50 39 50 20 OBO EGS
VHF power supply units, IP44 CEE connection unit, 6 A CEE-6A CEE socket with 60 mm fastening track, 3-pin + N + PE, 400 V, 6 A, 6 h. 9,00 609 87 4 CEE connection unit, 32 A CEE-32A CEE socket with 60 mm fastening track, 3-pin + N + PE, 400 V, 32 A, 6 h. 20,400 609 87 6 EGS OBO 2
OBO BETTERMANN GmbH & Co. KG P.O. Box 20 58694 Menden, Germany OBO BETTERMANN Order no. 05/206 EN Customer Service Germany Tel. +49 (0)2373 89-700 Fax +49 (0)2373 89-238 E-mail: export@obo.de www.obo-bettermann.com THINK CONNECTED.