Stainless steel housing BGS type BGS-ZM Series IP9K: Highly water resistant Tough structure for food processing line needs washing with high temperature and high pressure water. turn sensitivity adjustment potentiometer For production line needs washing Selection table Type Sensing distance (Adjustable distance) 1 1mm 1mm BGS-ZM1N BGS 1 mm mm Part number of PNP type has suffix P : For production line with detergent splash BGS-ZMN BGS-ZM1N BGS-ZM1P Accessories Wall mounting bracket Protective mounting bracket mm thick SUS bracket For meat and fresh food processing line www.optex-fa.com
IP9K protection 9 1 15mm IP9K is an rating of German standard DIN 5-9 extends the IEC 59 rating system for high-pressure, hightemperature wash-down applications. Test condition: A sensor on the turn table that rotates 5 times per minutes. Pressure: ~1bar Flow rate: 1~1 litre/minute Temperature: + * IP9K doesn t mean to guarantee that the sensor works under the test condition above. The sensor won t work correctly when the lens gets wet and the light is refracted. High-pressure, high-temperature, detergent wash-down resistant Tough structure Top cover: Poly Ether Sulphone (PES) Oil, detergent, high-temperature resistant. Top level protection in transparent plastic. SW, Pot: Poly Ether Etherketone (PEEK) Shock, scratch, stress, heat resistant. Highly resistant to chemical except concentrated sulfuric acid. Housing: SUS1L Highly corrosion-resistant. Detergent, bactericide resistant. Printing by laser marking There is no label attached so you don t have to care about interfusion into foods of the label unsticked. Lens PPSU for thru-beam, diffuse type Chemical, heat resistant. Very stable material. Lens PMMA with SiO coating for retro reflective type Oil, scratch resistant. Water repellent and anti-static. Gasket (FKM), cable (PVC) Chemical, oil resistant and flexible. turn sensitivity adjustment potentiometer helps easy mounting and easy position adjustment. High brightness LED by element enables stable detection. turn potentiometer element LED (A InGaP-LED)
Specifications Type Part number Sensing distance Adjustable distance Light source Spot size Response time Hysteresis Sensitivity adjustment Indicator Control output Operating mode Cable Power supply Power consumption Conformity Operating temp./humid. Environmental illuminance Vibration resistance Shock resistance Protection category Material Weight Accessory With 1mm x 1mm white paper BGS BGS-ZM1N BGS-ZMN 1~1mm 1~mm ~1mm ~mm element red LED mm at mm 19mm 5μs max. at 5mm % 以下 5% 以下 turn potentiometer Orange LED: output, Green LED: stable NPN (PNP) Open collector, Max.1mA/DCV Light ON/Dark ON selectable by switch Cable length: m, φ DC1~V including 1% ripple ma max. CE Feilen Level -5~+55 no condensation / 5~5%RH Sunlight: 1, lux max. Incandescent lamp:, lux max. 1~55Hz double amplitude1.5mm,,z hours 1G (1m/s ),,Z times IEC :IP7 DIN :IP9K Housing: SUS1L Top cover: PES Lens: PPSU Switch, Pot: PEEK Cable: PVC Gasket: FKM Approx. g excluding cable Mounting bracket:bef-w1b
Input/Output Diagrams NPN type PNP type Brown DC1 ~V Brown DC1 ~V Load Protection Main circuit Black Control output Main circuit Black Control output Protection Load Blue V Blue V Through beam emitter Notes When using switching regulator for power supply, please connect frame ground to earth ground. Wiring close to high voltage or power line to motors may cause malfunction because of inductive noise. Please wire separated from those lines. Please wait around 1msec before use sensor output after power up.
専用光電セン Stainless steel housing BGS type BGS-Z-M Dimensions Sensor 11 1. Sensitivity adjustment pot. Red LED: output Green LED: stable -M, Torque:.5Nm max. 1.9 1. Switch Light ON / Dark ON.1 5. B A. φ.mm core Type A Light axis B Light axis BGS-ZM1 1.7 1.5~. BGS-ZM 1.5~.5 Mounting bracket BEF-W1-B Bundled with sensor -R. 7. -R1 1.5 5.7 1 1 BEF-W1-A 1. 1. -R1 1. 1 9 -R1. 5. -R1 -R1 9.. 9.7 9.1. 5. 7. 5. 7. 5-R. 5. 5.. Protective mounting bracket LK-S1 9.7 -R. LK-S. 1 -R1. 9 1. 1 9 7 1.5 1 1. 9 Emitter Light axis 17.7 51 Emitter Light axis 17.7 1 7 1.5 5
Typical characteristic data BGS-ZM1N 1 1 1 5 BGS-ZMN Adjusted distance: 1mm White paper 9% 1 1mm 1 Distance: 1mm Distance: 5mm 1 Adjusted distance: mm Adjusted distance: 15mm White paper 9% 1 1mm 1 1 1 5 7 5 1 1 1 1 1 White paper 1 1 1 1 White paper Distance: 1mm Distance: 5mm 5 1 15 5 5 Spot size (mm) Spot size (mm) 1 1 1 1 5 5 15 1 5 1 1 1 1 1 5 1 15 5 5 5 paper size: 1 * 1mm 7 5 1 1 1 1 1 paper size: 1 * 1mm 7 5 1 5 1 15 5 5 用光電センサ サ Distance: mm Distance: mm Distance: mm Distance: mm 1 Distance: 1mm 1 Distance: 1mm