INSTALL GUIDE DOCUMENT NUMBER 870 REVISION DATE 080 FIRMWARE DIR-CH(RS)-CH8-[FLRSCH0] HARDWARE FLRSCH0 ESSORIES FLPROG (REQUIRED) DIRECTED XL-0 RF-KIT & ADS-HRN(RS)-XL0 (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM0 (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - OF PAGE OF FEATURES MAKE MODEL I NOTE WARNING: All vehicle doors must be closed and locked prior to remote start sequence. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS X LOCK /STANDALONE MOD. DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT BRAKE PEDAL STATUS OUTPUT TACHOMETER OUTPUT SECURE TAKEOVER GLOW PLUGS STATUS RAP SHUTDOWN CTRL DODGE RAM Dart STD key (Tip-Start) AT - 00 / 00 / 00 STD key (Tip-Start) AT -7 00 / 00 / 00 STD key (Tip-Start) AT 8 00 / 00 / 00 Diesel STD key (Tip-Start) AT -7 00 / 00 / 00 Diesel STD key (Tip-Start) AT 8
BOX CONTENTS - OF PAGE OF BOX CONTENTS MODULE T-HARNESS 0 PIN CONNECTOR BLUE BLACK 8 7 0 9 8 7 0 9 A B LED LED G F E PROGRAMMING BUTTON BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK MS MS VS VS VS VS VS PIN CONNECTOR AFTERMARKET HOOD SWITCH AND CABLE BLACK 8 7 0 9 C D 9 0 7 8 WHITE VS VS7 VS8 WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE
COMPATIBLE ESSORIES - OF PAGE OF DOC.: #870 080 RF KIT (accessories sold separately) ADS-HRN(RS)-XL0 DIRECTED XL0 RF KIT MODULE RF PORT XL0 RF DECODER XL0 ANTENNA TELEMATIC KIT (accessories sold separately) ADS-HRN(RS)-SM0 DIRECTED SMART MODULE TELEMATIC PORT (NC) (NC) (NC)
TYPE - WIRING DIAGRAM - OF PAGE OF MODULE IGNITION NODE A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS PTS IGNITION CONNECTOR IGNITION HARNESS A MS VS OBDII OBDII CONNECTOR OBDII HARNESS B PURPLE (NC) VS OBDII HOLDER 8 0 8 0 7 9 7 9 MS BROWN 8 PURPLE ONLY FOR ADS-HRN(RS)-CHR0 VER.0 NOTE (SEE NEXT PAGE) VS7 NC VS VS A PARKING LIGHT SWITCH LIGHT SWITCH CONNECTOR LIGHT SWITCH HARNESS C VS8 NC 8 0 7 9 GRAY/GREEN - HORN (-) OUTPUT OPTIONAL HORN (-) D 8 0 7 9 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-)
TYPE - WIRING DIAGRAM - OF PAGE OF NOTE ONLY FOR ADS-HRN(RS)-CHR0 VER.0 STEP : -IDENTIFY THE PURPLE (PIN 8) AND BROWN (PIN ) WIRES FROM THE 0 PIN BLACK CONNECTOR OF THE T HARNESS. -CUT THE PURPLE WIRE. -CAREFULLY STRIP THE BROWN WIRE USING A WIRE STRIPPER. STEP : -CONNECT AND SOLDER THE PURPLE WIRE TO THE BROWN WIRE. WARNING FAILURE TO PROPERLY SOLDER CAN RESULT IN FAULTY CONNECTIONS AND PRODUCT MALFUNCTION STEP : -INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE.
TYPE - WIRING DIAGRAM - OF PAGE 7 OF MODULE IGNITION NODE A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS PTS IGNITION CONNECTOR IGNITION HARNESS A MS VS OBDII OBDII CONNECTOR OBDII HARNESS B PURPLE (NC) VS OBDII HOLDER 8 0 8 0 7 9 7 9 MS BROWN 8 PURPLE ONLY FOR ADS-HRN(RS)-CHR0 VER.0 NOTE (SEE NEXT PAGE) VS NC VS7 VS8 A PARKING LIGHT SWITCH LIGHT SWITCH CONNECTOR LIGHT SWITCH HARNESS C VS NC 8 0 7 9 0 GRAY (NC) GRAY/GREEN - HORN (-) OUTPUT OPTIONAL HORN (-) D 8 0 7 9 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-)
TYPE - WIRING DIAGRAM - OF PAGE 8 OF NOTE ONLY FOR ADS-HRN(RS)-CHR0 VER.0 STEP : -IDENTIFY THE PURPLE (PIN 8) AND BROWN (PIN ) WIRES FROM THE 0 PIN BLACK CONNECTOR OF THE T HARNESS. -CUT THE PURPLE WIRE. -CAREFULLY STRIP THE BROWN WIRE USING A WIRE STRIPPER. STEP : -CONNECT AND SOLDER THE PURPLE WIRE TO THE BROWN WIRE. WARNING FAILURE TO PROPERLY SOLDER CAN RESULT IN FAULTY CONNECTIONS AND PRODUCT MALFUNCTION STEP : -INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE.
TYPE - WIRE CHART - OF PAGE 9 OF MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR RAM CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 00 / 00 / 00 STD key AT 00 Diesel / 00 Diesel / 00 Diesel STD key AT 8 8 CanH ~ Gray 0 pin 0 Orange (DATA) Trailer module, right of steering column ~ CanL ~ Gray 0 pin 0 Yellow (DATA) Trailer module, right of steering column ~ CanH ~ Gray 0 pin 0 Orange (DATA) Trailer module, right of steering column ~ CanL ~ Gray 0 pin 0 Yellow (DATA) Trailer module, right of steering column ~
TYPE - WIRING DIAGRAM - OF PAGE 0 OF MODULE IGNITION NODE A B C G F E D RF PORT/WEBLINK PORT TELEMATIC PORT VS VS PTS IGNITION CONNECTOR IGNITION HARNESS A MS VS OBDII OBDII CONNECTOR OBDII HARNESS B PURPLE (NC) BROWN/RED BROWN/YELLOW VS OBDII HOLDER C 8 0 8 0 7 9 7 9 MS BROWN 8 PURPLE ONLY FOR ADS-HRN(RS)-CHR0 VER.0 NOTE (SEE NEXT PAGE) CUT THE BROWN/RED AND BROWN/YELLOW WIRES. INSULATE THE OBDII SIDE OF THE CUT WIRES AND CONNECT THE OTHER SIDE TO VEHICLE CANH AND CANL. VS7 CANH - 0 CANL - 0 B A TRAILER PACK CONNECTOR 7 GRAY 8 9 0 PARKING LIGHT SWITCH LIGHT SWITCH CONNECTOR 8 0 7 9 0 GRAY (NC) GRAY/GREEN - HORN (-) OUTPUT VS VS NC NC VS8 LIGHT SWITCH HARNESS D 8 0 7 9 0 GRAY/WHITE - HOOD STATUS (-) INPUT OPTIONAL HORN (-) WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-)
TYPE - WIRING DIAGRAM - OF PAGE OF NOTE ONLY FOR ADS-HRN(RS)-CHR0 VER.0 STEP : -IDENTIFY THE PURPLE (PIN 8) AND BROWN (PIN ) WIRES FROM THE 0 PIN BLACK CONNECTOR OF THE T HARNESS. -CUT THE PURPLE WIRE. -CAREFULLY STRIP THE BROWN WIRE USING A WIRE STRIPPER. STEP : -CONNECT AND SOLDER THE PURPLE WIRE TO THE BROWN WIRE. WARNING FAILURE TO PROPERLY SOLDER CAN RESULT IN FAULTY CONNECTIONS AND PRODUCT MALFUNCTION STEP : -INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE.
MODULE PROGRAMMING PROCEDURE - OF PAGE OF 0 Close driver door. Re-open driver door to wake up data bus. 07 ON Remove key. Connect module to computer and proceed with extended programming. 0 Press Unlock on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button. 08 ON Insert key into ignition. WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. 0 Wait, LED will flash GREEN once [x]. If LED does not flash GREEN, press Unlock on OEM remote again. 09 ON Turn key to ON position. ON Turn key to ON position. 0 ON Turn key to ON position. 0 Wait, LED will flash GREEN. Wait, LED will turn solid GREEN for seconds. 0 Wait, LED will turn solid RED. ON Turn key to position. 7 ON Turn key to position. 0 ON Turn key to position. WARNING: Disconnect power last. Disconnect module from vehicle. 8 ON Turn key to position.
MODULE PROGRAMMING PROCEDURE - OF PAGE OF 9 ON Turn key to position. 0 Module Programming Procedure completed.
VALET MODE PROGRAMMING PROCEDURE - OF PAGE OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to. 0 Time restriction. Complete next step within 7 seconds. 0 ON Cycle ignition ON five times [x /ON] rapidly. ENGINE STOP 0 Wait, LED will turn solid RED for seconds. 0 ON Set ignition to position. ENGINE STOP 0 Valet Mode Programming Procedure completed.
AFTERMARKET REMOTE PROGRAMMING - OF PAGE OF AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
PAGE OF MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 ON DOC.: #870 080 TO ESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP 0 0 [X]
MODULE NAVIGATION CHART - OF PAGE 7 OF MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 CONFIGURATION 0 DISARM/UNLOCK BEFORE 0 0 ON 0 RELOCK AFTER 0 0 ON 0 RELOCK AFTER SHUTDOWN 0 0 ON 0 FORCE UNLOCK ALL ON FIRST PRESS 0 0 ON 0 TAKEOVER 0 ENABLE 0 DISABLE* 0 N/A 0 N/A 07 N/A 0 N/A 0 0 MIN 0 0 MIN 0 0 MIN 08 MODULE RUN TIME 0 MIN 0 MIN 0 0 MIN 07 MIN 08 MIN 0 0 SEC 0 0 SEC 0 08 SEC 09 WAIT TO DELAY 0 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC 0 N/A 0 N/A N/A 0 N/A N/A 0 N/A N/A 0 N/A
MODULE NAVIGATION CHART - OF PAGE 8 OF MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS *Vehicle will shutdown when a door is opened. 0 DOUBLE LOCK HORN EVENT TRIGGER 0 LOCK + UNLOCK 0 LOCK + UNLOCK + 0 CONFIGURATION 0 DOUBLE LOCK + 0 0 msec HORN CHIRPS WIDTH 0 msec 0 0 msec 0-07 Technical Support only 0 N/A 0 N/A
REMOTE ER ERROR CODES - OF PAGE 9 OF REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 0 Engine tach signal is lost. 0 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 N/A N/A N/A N/A N/A N/A CAN communication failure during RS sequence.
MODULE DIAGNOSTICS - OF PAGE 0 OF TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - OF PAGE OF 0 Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed.
TAKEOVER PROCEDURE - OF PAGE OF >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press and release BRAKE pedal. 0 Time restriction. Complete steps to within seconds. 07 Take over procedure completed. 0 Press unlock on OEM or aftermarket remote. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Open driver door and enter vehicle. 0 Close driver door. 0 ON Turn key to ON position.
INSTALLATION CHECKLIST - OF PAGE OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question : Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Enter vehicle and close the doors. Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed.