ROTARY TILLER "N" SERIES Opration, Srvic & Parts Manual Octobr 2006 FORM: NTillrBook/NTillrBook_08-17
No part of this manual shall b rproducd, copid or dissminatd by any mans, without manufacturr prior authorization in writing. manufacturr rsrvs th right to mak any ncssary changs without giving prior notic, in ordr to optimiz th quality and safty faturs and dos not commit itslf to updating this manual vry tim a chang is mad. This booklt provids a thorough and accurat dscription of th instruction and maintnanc activitis to b carrid out on th tillr you purchasd. W congratulat you on your choic and urg you to thoroughly familiariz yourslf with and follow th instructions containd in this manual. This will assur you a long, saf and troubl fr working lif for your tillr. Th Manufacturr shall not assum any rsponsibility should problms aris as a rsult of lack of complianc with th instructions and/or oprator's nglignc. Th manual is dividd in chaptrs and paragraphs and th pags ar numbrd, thus offring accurat and prcis information. Dat of Purchas: Modl Numbr: Srial Numbr
TABLE OF CONTENTS INDEX GENERAL INFORMATION Symbols..................................Pag 1 Safty labls...............................pag 2 Tchnical data..............................pag 3 Main parts trminology........................pag 4 Idntification plat...........................pag 5 Rcommndd us..........................pag 5 Inappropriat us...........................pag 5 Torqu spcification..........................pag 5 SAFETY Safty in th work plac......................pag 6 Usr s rquirmnts..........................pag 6 Work clothing..............................pag 6 Gnral safty norms.........................pag 6 Prparation................................Pag 7 SET UP Attachmnt to th tractor......................pag 8 Quick hitch attachmnt.......................pag 10 PTO shaft connction.........................pag 12 Slip clutch driv shaft........................pag 12 Working dpth adjustmnt.....................pag 13 Lvling board adjustmnt.....................pag 13 MAINTENANCE Road transport.............................pag 14 Shut down................................pag 14 First chck................................pag 14 Evry 8 working hours........................pag 15 Evry 20 working hours.......................pag 15 Evry 50 working hours.......................pag 15 Evry 500 working hours......................pag 15 Rplacing clutch linings.......................pag 16 SPARE PARTS How to ordr spar parts......................pag 17 Troublshooting chart.........................pag 18 Tillr parts brakdown........................pag 19 Tillr parts list..............................pag 20 Garbox parts brakdown......................pag 23 Garbox parts list...........................pag 23 Drivlin assmbly...........................pag 25 Slip clutch assmbly..........................pag 26 Limitd warranty............................pag 27
GENERAL INFORMATION GENERAL INFORMATION APPLICATION Th N Sris Tillrs ar dsignd to till soil for sdbd or planting prparation. Th N Sris Tillrs ar adaptd for tractors with 540 rpm PTO spd and Catgory 1 and 2, 3-point hitch tractors up to 50 HP. Ths tillrs ar also Quick Hitch adaptabl (by mans of Quick Hitch Optional Kit). SYMBOLS This booklt contains thr "safty pictograms" which highlight th rlvant dangr lvls or important information: It draws th oprator's attntion to spcial situations which may jopardiz popl's safty. It draws th attntion to situations which unfavorably affct th machin fficincy, but not popl's safty. It is usd for gnral information, whn popl's safty or th fficincy of th parts ar not at risk. Pag 1
SAFETY LABELS SAFETY LABELS Th safty labls and information on th machin (labls 1, 2 and 3), must b complid with. Failur to comply with ths warnings may rsult in svr injuris or vn dath. Mak sur that th labls ar always prsnt and lgibl; should this not b th cas, contact your narst Garmor dalr to rqust rplacmnts 2 1 3 Pag 2
TECHNICAL DATA TECHNICAL DATA Modl N Wight Working Dpth Tilling Width Sid Driv (Approx.) (Max.) Blads HP (Qty.) cm Inchs kg lbs. cm Inchs Chain Gar Blads Blads /Flang Shap 130 54 30-60 355 780 20 8 * 30 6 Curvd 155 61 30-60 380 838 20 8 * 36 6 Curvd 180 71 30-60 394 868 20 8 * 42 6 Curvd 205 81 30-60 410 904 20 8 * 48 6 Curvd Whn asking for information or tchnical srvic, always spcify th machin typ and width. Pag 3
MAIN PARTS TERMINOLOGY MAIN PARTS TERMINOLOGY A) Main Fram B) PTO Guard C) Top Link Coupling D) Third Point Mast E) Garbox F) Transmission Cas G) Rar Board H) Skid I) Parking Stand J) Tins K) Rotor L) Lowr Hitch Blocks Pag 4
INFORMATION IDENTIFICATION PLATE An idntification plat is placd on ach tillr and is structurd as follows: Srial numbr (sampl): RECOMMENDED USE Th tillrs dscribd in this instruction and maintnanc manual, hav bn dsignd xplicitly to till th land. Any othr us jopardizs th oprator's safty and th machin intgrity. INAPPROPRIATE USE Th tillrs shall not b usd as follows: Connctd to vhicls which do not hav a suitabl powr or wight. Without bing proprly installd by scuring th hitch brackts to all thr points of th tractor lift unit. Tilling of xtrmly stony or unsuitabl ground. In clos proximity to prson/s whn powr is ngagd. Do not stand or stp on th quipmnt whn it is bing opratd or transportd. Do not oprat th machinry whil waring unsuitabl (loos fitting) clothing. TORQUE SPECIFICATIONS For corrct hardwar tightning on th tillr, w suggst th us of suitabl torqu wrnch and th applicabl torqu as listd in th tabl blow: M-THREADED SCREW/BOLTS Bolt grad Thrad 8.8 10.9 Nm Lb-ft Nm Lb-ft M6 11 8.5 17 12 M8 28 20 40 30 M10 55 40 80 60 M12 95 70 140 105 M14 150 110 225 165 M16 240 175 305 225 M18 330 250 475 350 Pag 5
SAFETY SAFETY IN THE WORKPLACE Most of th accidnts, which occur whil th oprator is using th machin or th quipmnt or carrying out maintnanc and rpair activitis, ar causd by th non-complianc with th main safty rquirmnts. Thrfor th potntial risks must b fully undrstood and spcial attntion must b paid to th activity which is bing xcutd. USER'S REQUIREMENTS If potntially dangrous situations ar known, accidnts can b prvntd! Th quipmnt usr must hav th following: Physical: good sight, co-ordination and capability to xcut all instructions in a saf mannr. Mntal: th usrs must undrstand and follow th prscribd norms, ruls and safty masurs. Thy must b carful, pay attntion to thir own safty and th safty of othr popl and act proprly and in a rsponsibl way. Training: th usrs must rad and undrstand this manual, its picturs and charts, and th idntification and hazard plats. Thy must b spcializd, traind and qualifid on any us and maintnanc activitis. WORK CLOTHING Th following clothing and prsonal protctiv quipmnt must b usd whn working and xcuting maintnanc and rpair activitis: Ovralls or any othr comfortabl outfit; mak sur that thy ar not too loos sinc thy might b caught by moving parts. Protctiv glovs. Goggls or mask to protct th ys and fac. Safty hlmt. Safty shos. Mak sur that th prsonal protctiv quipmnt is proprly stord and complis with th laws in forc. GENERAL SAFETY NORMS Th faturs of th ara whr work is taking plac must always b takn into considration: Do not stand in th working radius of th oprating machinry or any othr machin accssoris whn th quipmnt is running. Pag 6
PREPARATION Prpar th work: Do not drink alcohol, tak drugs, or any othr substancs which may affct your ability to us th quipmnt bfor or whn working. Mak sur that thr is sufficint ful in th tractor to prvnt th machin from stopping during work. Do not us th quipmnt undr unsaf conditions,.g. do not mak tmporary rpairs just to start or kp working; do not work at night if th ara is not wll illuminatd. Whn working or xcuting maintnanc activitis, rmmbr: Th labls and stickrs providing instructions on th us of th quipmnt or information on dangrs must not b rmovd or hiddn, and must b lgibl. Do not rmov th safty dvics, covrs and safty guards, unlss maintnanc activitis ar bing carrid out. If th safty dvics must b rmovd, turn th ngin off, rmov thm corrctly and r-install thm bfor turning th tractor on. Do not lubricat, clan or adjust moving parts. Us th appropriat tools to xcut maintnanc or adjustmnt activitis on th quipmnt. Do not us damagd or unsuitabl tools,.g. plirs rathr than wrnchs tc. Prior to carrying out activitis on hydraulic lins undr prssur, or disconncting thir componnts, mak sur that th lin is no longr undr prssur and that it dos not contain any hot fluids. Chck all th fittings and mak sur that thy ar wll connctd bfor supplying prssur to th hydraulic lins. Mak sur that no tools, cloths or any othr matrials ar lft in aras whr moving parts ar prsnt whn th maintnanc and rpair activitis ar compltd. Do not giv dirctions and mak signals at th sam tim during a manuvr. Manuvr dirctions and signals must b givn from on prson only. Do not unxpctdly call an oprator, if not ncssary. Do not startl th oprator,.g. by throwing objcts. Pay attntion to popl in th vicinity of th work ara, spcially childrn! Mak sur that nobody is standing in th working rang of th quipmnt. Do not us th quipmnt to lift popl. Whn th quipmnt is not ndd, turn th ngin off, lav th vhicl on a flat surfac, with th first gar and th parking brak ngagd. Disngag th powr tak off. Do not xcut any claning, lubrication, rpair or adjustmnts whn th ngin is running and th quipmnt is in th raisd position. Do not work on stp slops, if th stability of th vhicl can b jopardizd. Manufacturr shall not assum any rsponsibilitis if ths instructions ar not strictly followd. Pag 7
SET-UP ATTACHMENT TO THE TRACTOR This tillr may b attachd to any tractor quippd with a Cat. 1 or 2, 3-point hitch with suitabl ball nds; it can also b attachd by mans of a Cat. 1 Quick Hitch. 3-POINT CATEGORY 1 HITCH To connct th tillr to th tractor's 3-point hitch, do th followng oprations: 1) Install both th uppr and th lowr link brackts with th hols facing down as shown in pictur 1; this givs you th standard A.S.A.E. vrtical dimnsion of 18" (pictur 1). 2) Rlas th bolts B and adjust th position of th brackts A to obtain standard A.S.A.E. horizontal displacmnt 26 7/8" (pictur 2). pictur 1 3) Rmov th cottr pins from th hitch pins (pictur 3). pictur 2 4) Rmov th lowr hitch pins from th lowr hitch brackts (pictur 3). pictur 3 Pag 8
SET-UP 5) Bfor attaching th quipmnt to th tractor, mak sur that th ground is smooth and flat and that nobody is standing btwn th tractor and th tillr; slowly mov th tractor towards th tillr by aligning th tractor liftr arms with th lift brackt hols (pictur 4); turn th ngin off and pull th brak. pictur 4 6) Insrt th lowr hitch pins through th hitch brackt and ball nds (pictur 5). 7) Scur thm by mans of th cottr pins which wr prviously rmovd (pictur 5). pictur 5 8) Connct th tractor top link to th third uppr point by rmoving th pin locatd btwn th two plats, insrting th top link and scuring it by mans of th hair pin. Shift th parking stand in th uppr position. 9) Adjust th top link so that th uppr part of th fram is paralll to th ground. Block all th linking parts by mans of th sway chains or arms. 10) Mak sur that th cntral unit axis (garbox assmbly) is paralll to th ground, thus minimizing th strsss on th powr tak off and incrasing th working lif of th quipmnt. Aftr xcuting all th abov mntiond activitis, mak sur that all th nuts and bolts ar tightnd. Pag 9
SET-UP 3-POINT CATEGORY 2 HITCH To connct th tillr to th tractor's Cat. 2, 3-point hitch, do th following oprations: 1) Install th uppr link brackt with th hols facing up and th lowr link brackts with th hols facing down as shown in pictur 6; this givs you th standard A.S.A.E. vrtical dimnsion of 20". pictur 6 2) Rla th bolts B and adjust th position of th brackts A (as shown in pictur 2) to obtain horizontal displacmnt 32 1/2" (pictur 7). pictur 7 3) Rmov th cottr pin, shift th pin to th gratr diamtr and rinsrt th cottr pin (pictur 8). pictur 8 4) Rpat th sam oprations as dscribd for Cat. 1 hitch. Pag 10
SET-UP 3-POINT CATEGORY 1 QUICK HITCH Th N Sris Tillrs ar Cat. 1 Quick Hitch adaptabl. To attach th implmnt to th tractor it is ncssary to ordr th Quick Hitch Kit composd of 3 bushings. Th following oprations ar ndd: 1) Plac th bottom brackts with hols facing up and th uppr brackt with th hol facing down as shown in pictur 5; this givs you th standard A.S.A.E. dimnsion of 15" for Quick Hitch (pictur 9). 2) Rlas th bolts B and adjust th position of th brackts A to obtain horizontal displacmnt of 26 7/8" (pictur 2). pictur 9 3) Insrt th lowr bushing of th kit in th lowr hitchs (pictur 10). pictur 2 4) Insrt th lowr hitch pins through th hitch brackt and bushing (pictur 10). 5) Scur thm by mans of th hair pins which wr prviously rmovd (pictur 10). 6) Rpat th sam oprations from 3 to 5 for th uppr brackt with th uppr bushing. pictur 10 7) Bfor attaching th quipmnt to th tractor, mak sur that th ground is smooth and flat and that nobody is standing btwn th tractor and th tillr; slowly mov th tractor towards th tillr by aligning th tractor liftr arms with th brackt hols; turn th ngin off and pull th brak. Pag 11
SET-UP 8) Lift th Quick Hitch until its hooks ngag th hitchs of th implmnt. 9) Rais th parking stand to th uppr position. PTO SHAFT CONNECTION Bfor installing th PTO shaft mak sur that th RPM rating and th dirction of rotation match thos of th tractor. Carfully rad th PTO shaft and tractor instructions. Furthrmor, accuratly rad th instructions of th manufacturr of th PTO shaft and of th tractor. Bfor starting any activity, mak sur that th guards ar installd on th powr tak off of th tractor and PTO shaft. Mak sur that thy covr th PTO shaft throughout its lngth. Whn fully xtndd, th plastic pips must ovrlap by at last 1/3 of th lngth of th pips (LT). Whn rtractd, th minimum accptabl claranc is 2. SLIP CLUTCH DRIVE SHAFT This tillr has a driv shaft with a slip clutch, which has bn calibratd for a crtain ovrload. To adjust th clutch, tightn or loosn bolts qually. Don t ovr-tightn or clutch will lock and not slip undr strss, which could caus damag during opration. Th clutch assmbly should gt warm (normal tmp. 104-122 F) undr normal opration. If th clutch gts xtrmly hot, this is a sign of slippag. If th machin sits for an xtndd priod of tim with no usag, th bolts should b loosnd and th PTO ngagd. This will allow th clutch discs to bcom fr again. Aftr a fw sconds, shut-off th tractor and rtightn bolts qually. Rchck clutch assmbly for tmpratur aftr using in tilling application. If it is too hot, th bolts nd tightning. If it is too cool, loosn bolts. Pag 12
SET-UP WORKING DEPTH ADJUSTMENT Th working dpth of th quipmnt dpnds on th position of th latral skids. If th skids ar raisd, th working dpth incrass; if th skids ar lowrd, th working dpth dcrass. To adjust th working dpth, loosn nut A (pictur 1 ), rmov nut B and adjust th skid hight according to th hols C. Whn th adjustmnt is compltd, tightn both th scrws to th corrct torqu, according to th valus suggstd in Torqu Spcifications, pag 5. IMPORTANT: Mak sur that th skids ar st at th sam hight on both sids. pictur 1 LEVELING BOARD ADJUSTMENT Th rar lvling board can b adjustd in hight to bttr compact th ground and mak it flat. Th adjustmnt can b mad by rlasing chains A (pictur 1 ) from uppr hooks B and insrting it back to th dsird hight. pictur 1 Pag 13
MAINTENANCE Ths activitis must b carrid out with th ngin off, th powr tak off disngagd and th hand brak applid. If ndd, lift th quipmnt and plac it on supports, thus prvnting any injuris that might b causd by a suddn fall of th quipmnt. START UP Aftr carrying out ths adjustmnts, th quipmnt is rady for us. Whn at th working ara, do not start th powr tak off with th tillr in working position in th ground. B sur to lift it by a fw cntimtrs using th tractor lift. Start th ngin, ngag th powr tak off, lowr th quipmnt to its working position and start. ROAD TRANSPORT With rfrnc to road transport, follow local traffic rgulations. SHUT DOWN Th following activitis ar rcommndd if th tillr will not b usd for a long priod of tim: 1. Clan and dry th quipmnt. 2. Inspct th quipmnt and rplac th damagd or worn parts if ncssary. 3. Tightn all th scrws and nuts. Lubricat and covr th machin with a tarpaulin and stor it in a dry plac. MAINTENANCE Maintnanc is crucial for th working lif and fficincy of any agricultural quipmnt. If th quipmnt is proprly maintaind and opratd, a long working lif and oprator safty ar assurd. Th maintnanc intrvals indicatd in this booklt ar providd as a mr rfrnc and ar rlatd to normal working conditions; changs may occur dpnding on th typ of activitis, nvironmntal dust, sasonal factors, tc. Bfor injcting lubricating gras into th gras fittings, clan th fittings to prvnt mud, dust, or any othr forign mattr from contaminating th gras and rducing th lubrication ffct. Whn adding or changing th oil, us th sam typ of oil to prvnt mixing oils with diffrnt faturs. All maintnanc activitis must b carrid out with th tillr rsting horizontally on th ground. Aftr using th quipmnt for a fw hours, mak sur that all th bolts (spcially tin bolts) ar tightnd; rgularly chck all th machin guards. FIRST CHECK Aftr 50 working hours, chang th oil in th garbox and mak sur that all th scrws and bolts ar tightnd. Pag 14
EVERY 8 WORKING HOURS Gras th PTO shaft crosss. EVERY 20 WORKING HOURS Gras th PTO shaft innr driv tub. MAINTENANCE EVERY 50 WORKING HOURS Chck th oil lvl in th xtrnal rotor baring through th inspction plug A. If ndd rmov th plug B and add SAE EP 80W90 oil (pictur 13). Chck th oil lvl in th cas/bvl gar pair by rmoving garbox s uppr oil plug (A - pictur 14). If ndd add SAE EP 80W90 oil. Chck th oil lvl in th sid transmission (A - pictur 15). If ndd add SAE EP 80W90 oil. Mak sur that all th scrws and bolts, spcially on th blads, ar tightnd. Chck slip-clutch spring tnsion (1050 Nm). EVERY 500 WORKING HOURS Chang th oil of th cas/bvl gar pair, sid transmission and rotor support; us SAE EP 80W90 oil. Contact th closst dalr for this maintnanc activity. pictur 13 pictur 14 pictur 15 Th old oil must b disposd of in complianc with th local laws whr ths activitis ar carrid out; do not spill or dispos of wast oil on th ground. Th maintnanc activitis must b carrid out with th ngin off, th powr tak off disngagd, th parking brak ngagd, and th quipmnt placd on th ground. Pag 15
REPLACING CLUTCH LININGS 1. Mount clutch assmbly in vis. 2. Rmov all bolts and nuts (Rf. A). 3. Disassmbl all componnts. 4. Chck th condition of all parts, friction plats spcially. 5. Rplac clutch linings (Rf. B). 6. Rassmbl th componnts, install spring with thir corrsponding bolts and nuts. 7. Tightn nuts following an altrnating cross pattrn until raching a hight of 27.6 mm (1.083"). 8. Chck that th hight is th sam for all springs. 9. Rinstall drivlin, making sur all shilds ar in plac. Pag 16
SPARE PARTS BLADES REPLACEMENT To assur th optimum fficincy of th machin, mak sur that th tillr blads ar in a good working condition and that thir bolts ar tightnd; rplac thm if thy ar brokn or bnt. Th nw parts must b installd in th original position. Bfor rplacing th blads, turn th tractor ngin off, pull th parking brak, disngag th powr tak off, rais th tillr using th tractor lift, and install supports to prvnt accidntal dropping of th machin. Pay spcial attntion to th bolts A on th blads (pictur 16): th scrw had must b placd on th blad sid, with th washr and th nut on th flang sid, so that th bolts cannot loosn whil th quipmnt is bing usd. Whn svral blads must b rplacd, rplac on blad at a tim, so that th initial hlical layout is maintaind (pictur 16). pictur 16 HOW TO ORDER SPARE PARTS For spar parts rqusts plas rfr to our spar parts catalogu. Th spar parts can b ordrd from th dalr or srvic cntr. Th following data must always b spcifid: Equipmnt modl and width. Part numbr of th rqustd componnt. If th cod numbr is missing, indicat th rfrnc numbr in which it is shown and th rlvant rfrnc. Dscription of th part and rqustd quantity. Rqustd typ of transport. Should this information not b providd, th dalr or srvic cntr shall not b rsponsibl for dlays causd by circumstancs byond thir control. Th addrss shall b rsponsibl for any transport chargs. Pag 17
TROUBLESHOOTING CHART PROBLEM CAUSE SOLUTION Driv shaft damagd Rplac worn driv shaft Excssiv vibration Rotor shaft dos not turn Tilling dpr on on sid Tillr bouncing Laving tir tracks PTO will not untlscop Tins brokn off Bnt rotor shaft PTO Clutch slipping Tractor lowr lift arm out of adjustmnt Tillr dpth skid not proprly adjustd Trying to go too dp on first pass Tractor in too high a gar Tirs st out too wid Tractor too larg Impropr lubrication PTO twistd Shilds damagd Rplac damagd tins Rplac rotor shaft Chck slip clutch adjustmnt Rplac clutch discs Adjust lift arm Adjust skids to lvl dpth Rais tillr so tilling 3" dp Tillr runs smoothr in first or scond gar St in tractor tirs Offst tillr to covr right tir tracks Sparat and gras both halvs Rplac twistd parts Rplac shilds Pag 18
"N" TILLER ASSEMBLY Pag 19
TILLER ASSEMBLY REF# QTY. PART NO. DESCRIPTION 1 3 6351004 Split Pin 4 x 80 2 1 5304001 Uppr Pin 3 1 4138035 Protction Support 4 2 34100016 Nut M16 UNI 5587 5 2 34121016 Washr UNI 1751 6 1 4007937 Uppr 3rd Point 7 1 4302257 U Scrw 8 1 4008697 Junction For 3rd Point 9 2 6330636 Split Pin 10 4 4307802 U Scrw 11 18 34100014 Nut M14 UNI 5587 12 1 4007935 Plat DX Lowr 3 Pt Hitch 12 1 4007936 Plat SX 13 As Rq'd* 34032014 Washr 14 FIAT 10188 14 2 4309179 Lowr Pin 15 1 3442022 Plug M22 x 1.5 16 1 4018347 Covr 17 18 31510025 Bolt M10 x 1.5 x 25 UNI 5739 18 1 4788398 Gaskt 19 2 30210 Baring 30210 20 1 6310090 Circlip 21 1 4598238 Spacr 22 1 4728017 Intrmdiat Gar Z=41 23 2 4232111 Latral Bonnt Pin 24 As Rq'd* 34121012 Washr UNI 1751 25 As Rq'd* 34100012 Nut M12 UNI 5587 26 1 4937901 Transmission Sid Plat 27 22 34121010 Washr UNI 1751 28 18 34100010 Nut M10 UNI 5587 29 10 31514035 Bolt M14 x 2 x 35 UNI 5739 30 2 4332278 U Scrw 31 2 4137741 Support 32 1 4007905 Fram N155 32 1 4007906 Fram N180 32 1 4007907 Fram N205 33 As Rq'd* 34101014 Nut M14 UNI 5587 34 As Rq'd* 31512035 Bolt M12 x 1.75 x 35 UNI 5739 35 1 4937902 Extrnal Sid Plat 36 1 4007002 Right Skid 37 1 6800045 O-Ring 38 1 4208153 Pin Pag 20
TILLER ASSEMBLY REF# QTY. PART NO. DESCRIPTION 39 1 3441014 Oil Lvl Plug M14 x 1.5 40 1 6351003 Split Pin 3 x 60 41 1 5236115 Pin 42 1 34106040 Slf Locking Nut M40 x 2 43 18 34121014 Washr UNI 1751 44 1 4232106 Bonnt Pin N155 44 1 4232107 Bonnt Pin N180 44 1 4232108 Bonnt Pin N205 45 8 31512030 Bolt M12 x 1.75 x 30 UNI 5739 46 1 4007003 Lft Skid 47 1 4002376 Parking Stand 48 1 4002377 Support 49 1 6470114 Washr 50 2 31514040 Bolt M14 x 20 x 40 UNI 5739 51 1 4007919 Bonnt N155 51 1 4007920 Bonnt N180 51 1 4007921 Bonnt N205 52 1 4508003 Bonnt Chain 17 N155 52 2 4508002 Bonnt Chain 15 N180 & N205 53 1 4302183 Chain Hook N155 53 2 4302183 Chain Hook N180 & N205 54 1 4212214 Spring N155 54 2 4212214 Spring N180 & N205 55 2 34106014 Slf Locking Nut M14 56 4 31510030 Bolt M10 x 1.5 x 30 UNI 5739 57 1 3441014 Oil Plug M14 x 1.5 58 1 3444014 Oil Lvl Plug M14 x 1.5 59 1 34127035 Slf Locking Mtal Ring M35 x 1.5 60 1 4728337 Gar Z=32 61 1 6310100 Circlip 62 1 6309 Baring 6309 63 1 4788217 Gaskt 64 1 4708201 Hub Support 65 8 31712025 Bolt M12 x 1.75 x 25 UNI 5931 66 1 6203707 Oil Sal GNL IM 5470 67 1 4728200 Lft Rotor Hub 68 1 4148040 Dust Covr 69 1 4007942 Holdr Rotor N155 69 1 4007943 Holdr Rotor N180 69 1 4007944 Holdr Rotor N205 70 1 34106012 Slf Locking Nut M12 N155 Pag 21
TILLER ASSEMBLY REF# QTY. PART NO. DESCRIPTION 70 2 34106012 Slf Locking Nut M12 N180 & N205 71 As Rq'd* 31414040 Bolt M14 x 1.5 x 40 Lngth 20 72 As Rq'd* 4818224 Lft Squar Blad 73 As Rq'd* 4818225 Right Squar Blad 74 As Rq'd* 4818222 Lft Blad 75 As Rq'd* 4818223 Right Blad 76 1 4148030 Dust Covr 77 1 4708249 Right Rotor Hub 78 1 4208021 Washr, Spcial 79 1 4708239 Hub Support 80 1 6205300 Oil Sal 81 1 6307 Baring 6307 82 1 4788219 Gaskt 83 1 6800094 O-Ring 84 1 4708248 Baring Support 85 1 4138034 Joint Protction 86 3 33108020 Bolt M8 x 1.25 x 20 UNI 5449 87 7 34118008 Washr UNI 6593 88 1 30612030 Bolt M12 x 1.75 x 30 UNI 5933 89 1 34120012 Washr UNI 6592 N155 89 2 34120012 Washr UNI 6592 N180 & N205 90 4 31508016 Bolt M8 x 1.25 x 16 UNI 5739 91 1 3470118 Washr 92 2 4934778 Chain Plat N180 & N205 93 1 E8218635 Drivlin * Quantitis Rquird Rf # Quantitis for Modl Numbr N155 N180 N205 13 72 84 96 24 25 29 29 25 20 24 24 33 72 84 96 34 11 15 15 71 72 84 96 72 18 21 24 73 18 21 24 74 18 21 24 75 18 21 24 Pag 22
GEARBOX ASSEMBLY REF# QTY. PART NO. DESCRIPTION 1 3 33108020 Bolt M8 x 1.25 x 20 UNI 5449 2 7 34118008 Washr UNI 6593 3 1 4138035 Protction Support 4 1 34127035 Slf Locking Mtal Ring M35 x 1.5 5 1 35.72.10 Oil Sal 35 x 72 x 10 6 1 4138034 Joint Protction 7 1 6310072 Circlip 8 4 31508016 Bolt M8 x 1.25 x 16 UNI 5739 9 1 4657744 Garbox 10 1 3442018 Plug M18 x 1.5 11 1 4599031 Spacr 12 1 6207 Baring 6207 13 1 4227742 PTO Shaft 14 1 3441018 Plug M18 x 1.5 15 1 4788219 Gaskt 16 1 4647745 Covr 17 12 34121012 Washr UNI 1751 18 8 31512030 Bolt M12 x 1.75 x 30 UNI 5739 Pag 23
GEARBOX ASSEMBLY REF# QTY. PART NO. DESCRIPTION 19 14 31510025 Bolt M10 x 1.5 x 25 UNI 5739 20 16 34121010 Washr UNI 1751 21 1 4007965 Shaft Support N155 21 1 4007966 Shaft Support N180 21 1 4007967 Shaft Support N205 22 1 4728643 Pinion Z=15 23 1 30308 Baring 30308 24 1 4728642 Ring Bvl Gar Z=22 25 2 6320045 Circlip 26 1 4148067 Chain Plat N155 27 1 4788413 Gaskt 28 1 6311 Baring 6311 29 2 31510030 Bolt M10 x 1.5 x 30 UNI 5739 30 4 34100012 Nut M12 UNI 5587 31 4 31512035 Bolt M12 x 1.75 x 35 UNI 5739 32 1 4728336 Driving Gar Z=21 33 1 6309 Baring 6309 34 1 45x72x10 Oil Sal 45 x 72 x10 35 1 4217910 Shaft N155 35 1 4217911 Shaft N180 35 1 4217912 Shaft N205 36 1 4788693 Gaskt 37 1 4007958 Extrnal Support N155 37 1 4007959 Extrnal Support N180 37 1 4007960 Extrnal Support N205 38 1 6470117 Washr 39 1 4937914 Lifting Hook Plat N180 & N205 40 1 4937912 Spacr Plat Pag 24
DRIVESHAFT ASSEMBLY REF# QTY. PART NO. DESCRIPTION 2 1 1026010 Yok Assmbly, Tractor End 2A 1 1581038 Push Pin Kit 3 2 1006020 Cross Assmbly 4 1 1706027 Outr Tub Yok 5 1 6331080 Roll Pin 8 x 80 Outr Tub 6 1 1528074 Outr Tub 8 1 1526074 Innr Tub 9 1 1706029 Innr Tub Yok 10 1 1386016 Torqu Limitr, 2 Friction Discs 11 1 6331070 Roll Pin 8 x 70 Innr Tub 12 1 1786710 Tub Baring 13 2 1215733 Stiffning Ring 14 1 1785703 Standard Con 15 2 1215735 Stop Ring 16 2 1885709 Safty Slv 17 1 1776064 Outr Tub Shild 18 1 1877064 Innr Tub Shild 19 1 1785702 Short Con 20 1 1786711 Tub Baring, Innr Tub 23 1 90SC6064 Complt Protction 24 2 1006065 Anti-rotation Chain 25 1 1140001 Outr Dcal 26 1 1140003 Innr Dcal Pag 25
SLIP CLUTCH ASSEMBLY REF# QTY. PART NO. DESCRIPTION 1 8 6411010 Scrw Nut For Spring 2 8 1215012 Spring 3 1 1706033 Flang With Yok 4 1 1705009 Bushing 5 2 1808010 Friction Disc 6 1 1231038 Conical Clamp 7 1 1708907 Hub With Flang 8 1 6412012 Washr 9 1 6410712 Scrw Nut 10 1 1138008 Innr Disc 11 1 1138007 Prssur Disc 12 8 6001085 Bolt For Spring 13 1 6821271 Conical Clamp Kit Rplacmnt Pag 26
LIMITED WARRANTY GEARMORE, INC., warrants ach nw Garmor product to b fr from dfcts in matrial and workmanship for a priod of twlv (12) months from dat of purchas to th original purchasr. This warranty shall not apply to implmnts or parts that hav bn subjct to misus, nglignc, accidnt, or that hav bn altrd in any way. Our obligation shall b limitd to rpairing or rplacmnt of any part, providd that such part is rturnd within thirty (30) days from dat of failur to Garmor through th dalr from whom th purchas was mad, transportation chargs prpaid. This warranty shall not b intrprtd to rndr us liabl for injury or damags of any kind or natur, dirct, consquntial or contingnt, to prson or proprty. This warranty dos not xtnd to loss of crops, loss bcaus of dlay in harvsting or any othr xpnss, for any othr rasons. Garmor in no way warrantis ngins, tirs, or othr trad accssoris, sinc ths itms ar warrantd sparatly by ths rspctiv manufacturrs. Garmor rsrvs th right to mak improvmnts in dsign or changs in spcification at any tim, without incurring any obligations to ownrs or units prviously sold. GEARMORE, INC. 13477 Bnson Av. Chino, CA 91710 Always rfr to and hd machin oprating warning dcals on machin. Th srial numbr of this product is stord in our computr databas, thus submitting a warranty rgistration card is not rquird. Pag 27