Grease and Oil Injectors LIT099
AL-32 Grease Injector OVERVIEW The AL-32 Grease Injectors are designed for single line, high-pressure centralized lubrication systems. These injectors are available in either a stand-alone mount version for each bearing point or grouped in a manifold to lubricate multiple bearing points. The AL-32 injectors have an adjustable output range from 0.001-0.008 cu. in. (0.016-0.131 cc). Key Features and Benefits: 100% bolt-on replacement for Lincoln Centro-Matic SL-32 injector series stand-alone and manifold injectors Available in carbon steel or 316 stainless steel types. The 316 stainless steel meets or exceeds food processing applications Indicator stem provides visual check of injector operation Wide range of adjustment by individual outputs for greater application flexibility Individual injectors can be easily added or removed without redesigning the system Both the primary injector spring and the recharge piston spring are constructed from American made chrome silicon wire, which is shot peen, precision ground, and stress relieved to ensure maximum service life 3 year warranty Made in the U.S.A. Lincoln, Centro-Matic, and SL-32 are registered trademarks of Lincoln Industrial, Inc. 3
AL-32 SPECIFICATIONS AL-32 Injector / Manifold Assembly: Carbon Stainless Pressure* Output steel steel part no. part no. Description Min. Max. Vent Min. Max. Max temp. 715532 Stand-alone injector 715532-A 715532-SSA CRS replacement manifold injector 715532-A1 715532-SSA1 1 station CRS 715532-A2 715532-SSA2 2 station CRS 1,200 psi 83 bar 3,500 psi 242 bar 200 psi 14 bar 0.001 cu. in. 0.016 cc 0.008 cu. in. 0.131 cc 350 F 176 C 715532-A3 715532-SSA3 3 station CRS 715532-A4 715532-SSA4 4 station CRS * Typical pressure 1,500 psi (103 bar) Injector Repair / Overhaul Kit: Part no. 715532-KM Description AL-32 injector overhaul kit Additional Information: Adjustable output: 0.001 cubic inches to 0.008 cubic inches (6 turns) Stainless steel versions are 316 grade The AL-32 series injector has1/8 O.D. tube discharge ports The stand-alone AL-32 has a 1/4-18 NPTF male inlet, while the manifold version comes with the 1/4 NPTF female manifold inlet bolt and necessary hardware, which allows it to mount to any existing Lincoln SL-32 series manifold All packing glands are American made, Mil-Spec, Viton 4
AL-32 DIMENSIONS Dimensions: A B Part no. in. mm. in. mm. 715532-A1 1 1/4 715532-A2 2 51 715532-A3 715532-A4 2 3/4 3 1/2 32 70 89 1 3/4 2 1/2 3 1/4 4 44 63 83 102 5
OVERVIEW AL-43 Oil Injector The AL-43 Oil Injector is designed for single line, high-pressure centralized lubrication systems. This injector is available in manifold mount versions to lubricate multiple bearing points. The AL-43 injector has an adjustable output range from 0.001-0.008 cu. in. (0.016-0.131 cc.). Key Features and Benefits: 100% bolt-on replacement for Lincoln Centro-Matic SL-43 injector series stand-alone and manifold injectors Wide range of adjustment by individual outputs for greater application flexibility Individual injectors can be easily added or removed without redesigning the system Indicator stem provides visual check of injector operation Both the primary injector spring and the recharge piston spring are constructed from American made chrome silicon wire, which is shot peen, precision ground, and stress relieved to ensure maximum service life 3 year warranty Made in the U.S.A. Lincoln, Centro-Matic, and SL-43 are registered trademarks of Lincoln Industrial, Inc. 6
AL-43 SPECIFICATIONS AL-43 Injector / Manifold Assembly: Part no. Description Min. Max. Vent Min. Max. 715543-A Oil replacement manifold injector Pressure* Output Max temp. 715543-A1 1 station oil 715543-A2 2 station oil 750 psi 52 bar 1,000 psi 69 bar 150 psi 10 bar 0.001 cu. in. 0.016 cc 0.008 cu. in. 0.131 cc 350 F 176 C 715543-A3 3 station oil 715543-A4 4 station oil * Typical pressure 850 psi (59 bar) Additional Information: Adjustable output: 0.001 cubic inches to 0.008 cubic inches (6 turns) The AL-43 series injectors have 1/8 O.D. tube discharge ports The stand-alone AL-43 has a 1/4-18 NPTF male inlet, while the manifold version AL-43 comes with the 1/4 NPTF female manifold inlet bolt and necessary hardware, which allows it to mount to any existing Lincoln SL-43 series manifold All packing glands are American made, Mil-Spec, Viton 7
AL-43 DIMENSIONS Part no. 715543-A1 715543-A2 715543-A3 715543-A4 Dimensions: A B in. mm. in. mm. 1 1/4 2 51 2 3/4 3 1/2 32 70 89 1 3/4 2 1/2 3 1/4 4 44 63 83 102 8
AL-1 Grease Injector OVERVIEW The AL-1 Grease Injectors are designed for single line, high-pressure centralized lubrication systems. These injectors are available in either a stand-alone mount version for each bearing point or grouped in a manifold to lubricate multiple bearing points. The AL-1 injectors have an adjustable output range from 0.008-0.080 cu. in. (0.131-1.31 cc.). Key Features and Benefits: 100% bolt-on replacement for Lincoln Centro-Matic SL-32 injector series stand-alone and manifold injectors Available in carbon steel or 304 stainless steel types Wide range of adjustment by individual outputs for greater application flexibility Individual injectors can be easily added or removed without redesigning the system Indicator stem provides visual check of injector operation Both the primary injector spring and the recharge piston spring are constructed from American made chrome silicon wire, which is shot peen, precision ground, and stress relieved to ensure maximum service life 3 year warranty Made in U.S.A. Lincoln,Centro-Matic, and SL-32 are registered trademarks of Lincoln Industrial, Inc. 9
AL-1 SPECIFICATIONS Carbon Stainless Pressure* Output steel steel part no. part no. Description Min. Max. Vent Min. Max. 715501 Stand-alone injector 715501-A 715501-SSA CRS replacement manifold injector Max. temp. 715501-A1 715501-SSA1 1station CRS 715501-A2 715501-SSA2 2 station CRS 1,850 psi 128 bar 3,500 psi 242 bar 600 psi 41 bar 0.008 cu. in. 0.131 cc 0.080 cu. in. 1.31 cc 350 F 176 C 715501-A3 715501-A4 715501-SSA3 715501-SSA4 3 station CRS 4 station CRS 715501-A5 715501-SSA5 5 station CRS 715501-A6 715501-SSA6 6 station CRS * Typical pressure 2,500 psi (172 bar) Injector Repair/Overhaul Kits: Part no. 715501-KM 715501-KS Description AL-1 injector overhaul kit AL-1 injector seal repair kit Additional Information: Adjustable output: 0.008 cubic inch to 0.080 cubic inch range (8 turns) Stainless steel versions are 304 grade The stand-alone injector has a 3/8-18 NPTF male inlet, while the manifold replacement injector comes with the manifold inlet bolt and necessary hardware All packing glands are American made, Mil-Spec, Viton construction The AL-1 series injectors have 1/8 NPSF discharge ports 10
AL-1 DIMENSIONS Dimensions: Part no. 715501-A1 715501-A2 715501-A3 715501-A4 715501-A5 715501-A6 A B in. mm. in. mm. 2 1/2 63 Single Mounting Hole 3 76 1 1/4 2 1/2 3 3/4 5 32 63 95 23 4 1/4 5 1/2 6 3/4 8 108 140 171 203 11
OVERVIEW AL-11 Grease Injector The AL-11 Grease Injector is designed for single line, highpressure centralized lubrication systems. This injector is available in a stand-alone mount version for each bearing point. The AL-11 injector has an adjustable output range from 0.050-0.500 cu. in. (0.82-8.20 cc.). Key Features and Benefits: 100% bolt-on replacement for Lincoln Centro-Matic SL-11 injector Injector body is sealed at both ends with American made, Mil-Spec, Viton O-rings Primary piston seal ring is made of Parker 1090 Compound, Carboxilated- Nitrile for superior seal life (also available in Viton) The injector spring is constructed from American made chrome silicon. It is shot peen, precision ground, and stress relieved to ensure maximum service life The slide valve is precision hone matched fit to 150 millionths clearance 3 year warranty Made in U.S.A. Lincoln,Centro-Matic, and SL-11 are registered trademarks of Lincoln Industrial, Inc. Parker,1090 Compound, and Carboxilated Nitrile are registered trademarks of Parker Industries Inc. 12
AL-11 SPECIFICATIONS Pressure* Output Part no. Description Min. Max. Vent Min. Max. Max. temp. 715511 Grease injector 1,000 psi 69 bar 3,500 psi 242 bar 800 psi 55 bar 0.050 cu. in. 0.82 cc 0.500 cu. in. 8.2 cc 350 F 176 C * Typical pressure 2,500 psi (172 bar) Injector Repair/Overhaul Kit: Part no. 715511-KM Description Injector overhaul kit Additional Information: Adjustable output: 0.050 cubic inch to 0.500 cubic inch range (11 1/2 turns) 1/2 NPSF inlet port standard 1/4 NPSF discharge port All packing glands, O-rings, and backup rings are American made, Mil-Spec, Viton 13
AL-11 DIMENSIONS 14
INJECTOR SYSTEM COMPONENTS Description Part No. CLS 1000 Controller 387780 Vent valve 382600 2-way solenoid valve, 115 Vac 387449-1 Air FRL (filter) 339934 FRL (gauge 1/4 mini 0-30) 339947 FRL (gauge (1/4 mini 0-60) 339948 FRL (gauge (1/4 mini 0-300) 339949 FRL bracket 339925 Pressure switch 340098 15
Injector Pumps 17
OVERVIEW Injector and Dual Line Pumps Pump Packages (Pneumatic) Alemite s standard duty pump packages are available in drum sizes from 35 to 400 lbs. (16 to 180 kg.). These pumps offer delivery rates up to 5.25 lbs. (2.3 kg.) per minute. Key Features and Benefits: All-steel construction provides unmatched durability Wide range of choice in pump ratios and delivery provides the right pump for each application in all types of lubrication systems Case-hardened mechanical directional valves operate for years in harsh environments without sensitivity to dirt or contaminants 19
Injector Pumps 21
INJECTOR AND DUAL LINE PUMP SPECIFICATIONS Grease Pump Packages Part no. 331380-E1 331380-A5 8550-A1 331380-B5 331571-C5 331571-A5 331571-B5 711-R 711-S Note: Ratio 50:1 50:1 50:1 26:1 26:1 26:1 40:1 40:1 Delivery/ minute lbs. (kg.) 2.5 (1.1) 2.5 (1.1) 2.5 (1.1) 5.25 (2.3) 5.25 (2.3) 5.25 (2.3) 0.75 (0.33) 0.75 (0.33) Maximum pressure psi (bar) 7,500 (518) 7,500 (518) Fits drum lbs. (kg.) Follower Cover 35 (16) 337665 338166 120 (50) Includes 331380-A5, 338802 & 338371 7,500 (518) 5,200 (359) 5,200 (359) 5,200 (359) 6,000 (414) 6,000 (414) 400 (180) 35 (16) 120 (50) 400 (180) 35 (16) 35 (16) 338802 338911 338825 338802 338911 337665 337665 338371 318040-4 338166 338371 318040-4 338141 338166 Use 340090 universal adapter for standard pump sizes in non-standard plastic buckets; order follower and cover separately unless otherwise noted Grease Pumps with Built-in Return to Reservoir Part no. 339359-A1 339359-A1* 339359-B1 339359-C1 340031 Ratio 50:1 50:1 50:1 50:1 Delivery/ minute lbs. (kg.) 2.5 (1.1) 2.5 (1.1) 2.5 (1.1) 2.5 (1.1) Maximum pressure psi (bar) 7,500 (518) 7,500 (518) 7,500 (518) 7,500 (518) Fits drum lbs. (kg.) Follower Cover 35 (16) 337665 338166 20 kg. 120 (50) 400 (180) 338992 338802 338911 Includes 339359-A1, 338825 (follower), 338141 (cover), 382600 (pressure relief valve), and 340090 (adaptor) * Metric drum, follower, and cover Note: Order follower and cover separately unless otherwise noted 338982 338371 318040-4 Oil Pump Packages Part no. 331571-C5 331571-A5 331571-B5 8568-A4 Ratio 26:1 26:1 26:1 4:1 Delivery/min. gal (liter) 0.75 (2.8) 0.75 (2.8) 0.75 (2.8) 0.3 (1.1) Maximum pressure psi (bar) 5,200 (359) 5,200 (359) 5,200 (359) Fits drum gal. (liter) 5 (18.9) 16 (60.6) 55 (208.2) Stub* * Order downtube extension separately Note: Order follower and cover separately unless otherwise noted Cover 338166 338371 318040-4 23