Catalog PN2-2 Pancake II ir Cylinders Superior Interchangeable Industrial ir Cylinders
Pancake II Cylinders Product Index Standard Series PSD, PSR, PSX, PWD, PTD How it works.................................... 3 How to Order.................................... 5 List prices..................................... 24 Dimensions.................................. 6-9 Options...................................... 8, 9 Weights........................................ 7 Repair kits..................................... 27 Nonrotating, Twin Rod Series PND How it works................................... 10 How to Order................................... 11 List prices..................................... 25 Dimensions................................. 12, 13 Options.................................... 12, 13 Weights....................................... 12 Repair kits..................................... 27 Multi-Power Series PM2,, How it works.................................. 14 How to Order.................................. 15 List prices.................................... 25 Dimensions................................ 16, 17 Options...................................... 17 Weights...................................... 17 Repair kits.................................... 27 3-Position Series P3D How it works................................... 18 How to Order................................... 19 List prices..................................... 26 Dimensions................................. 20, 21 Options.................................... 20, 21 Weights....................................... 21 Repair kits..................................... 27 Magnetic Position Sensing Sensors....................................... 23 Quick disconnect cordsets........................ 23 ccessories ll series...................................... 22 2 Duralon is a registered trademark of Rexnord Corp. Magnalube -G is a registered trademark of Carleton Stuart Corp. Multi-Power and Pancake are registered Specifications trademarks subject of Fabco-ir, to change Inc. without Dacron notice, Teflon or incurring, and Viton obligation are registered trademarks of DuPont Corp. 11-15-01
Continuing the Space Saving Tradition... The Pancake II Direct Interchange ir Cylinders Hard chrome plated stainless steel piston rod better Piston Rod Bushing: Captive in cylinder head Nonmetallic Duralon Self lubricating Higher load bearing capacity Lower coefficient of friction No slip-stick superior Cylinder Wall High strength composite Highly impact resistant Self lubricating Extremely smooth interior Low coefficient of friction Minimal heat build up Captive rod seal In precision machined groove Internally lubricated Buna-N O Ring Buna N O'Ring tube seals Magnalube G lubrication luminum alloy spacers (clear anodized) enclose stainless steel tie bolts luminum alloy heads (clear anodized) High strength threaded fastener and adhesive mates piston to rod Superior Interchangeable Industrial ir Cylinders Innovation For over 40 years our famous Pancakes have dominated as the world's first compact air cylinder line. Today, backed by decades of engineering and manufacturing innovation, our new Pancake II composite body air cylinders continue in the Pancake tradition with a wide selection of models and options. Packed with value Stainless steel tie bolts and aluminum spacers lock precision machined heads tightly around a unique, high strength, composite cylinder barrel. The barrel's extremely smooth, self-lubricating interior surface insures highly reliable performance and extended seal life. Its high impact resistance reduces chances of cylinder failure due to dings or dents. Zero slip-stick avoids problems that metal cylinders encounter when they sit in a static condition for extended periods of time. Combined with hard chrome plated stainless steel piston rods and a unique, nonmetallic rod bearing, the new Fabco-ir cylinder assembly assures optimal operation and longer product life. Exceptional Piston Rod Bearing The better the bearing, the more cycle life you can expect from your air cylinders. Pancake II cylinders incorporate a truly superior rod Thick cover prevents impact damage Internally lubricated Buna N O'Ring or optional U-Cup seals Duralon Rod Bearings Excel Load Capacity (psi) Friction Properties Machine Design 1972/73 Slip- Bearing Reference Issue Coefficient stick Porous Bronze... 4,500 Steel-on-steel....50 Yes Porous iron... 8,000 Bronze-on-steel....35 Yes Phenolics... 6,000 Sintered Bronze-on-steel Nylon... 1,000 with mineral oil....13 No TFE... 500 Bronze-on-steel Reinforced Telfon... 2,500 with mineral oil....16 No *TFE fabric... 60,000 Copper lead alloy-on-steel.22 Yes Polycarbonate... 1,000 cetal-on-steel....20 No cetal... 1,000 Nylon-on-steel....32 Yes Carbon-graphite... 600 Duralon-on-steel....05 -.16 No * Shows Duralon bearing classification. Not to be used for design purposes. Printed with permission by Rexnord Corp. bearing material - Duralon with the same field-proven performance you have come to expect from the six other Fabco-ir cylinder families. Duralon is a composite of a Teflon /Dacron fabric liner bonded to a supporting filament-wound, high strength, fiberglass and epoxy resin shell. Resistant to corrosion, moisture and temperature to 325 F, the bearing is reliable in any environment. It has an extremely high load bearing capacity, very low friction, and will not gall or score the piston rod (see physical properties in the table above). 11-28-01 Specifications subject to change without notice or incurring obligation 3
Pancake II Cylinders vailable in 5 styles 8 sizes 1/2" thru 4" Strokes to 4" standard Double acting, single rod Double acting, double rod Double acting, hole thru double rod Single acting, spring retracted rod Reverse acting, spring extended rod Ratings Standard Units all Series Body... Self-lubricating composite Heads... Clear anodized aluminum alloy Tie Bolts... Stainless steel Rod... Chrome plated stainless steel Piston... luminum alloy Rod end... Female thread with wrench flats Ports... Position #1 Seals...Internally lubricated Buna-N Lubrication... Magnalube -G Rod bushing... PTFE composite bearing Stroke tolerance................. ± 1/64" Media............................ ir Pressure rating, maximum......... 200 psi Minimum recommended operating pressure............. 15 psi Temperature rating Cylinder............. 25 to +225 F ( 32 to +121 C) Temperature rating Electronic sensors...... 4 to +176 F ( 20 to +80 C) pproximate Spring Forces Maximum Force 5.25 10.00 13.00 13.00 13.00 25.00 25.00 25.00 0.12 to 1" Stroke 4.25 6.00 6.50 6.50 6.50 12.50 12.50 12.50 Spring Rate (lbs/inch) for Stroke Range 1 to 2" Stroke 2.13 3.00 3.25 3.25 3.25 6.25 6.25 6.25 1 to 3" Stroke 1.42 2.17 2.17 2.17 4.17 4.17 4.17 3.001 to 4" Stroke 1.06 1.50 1.63 1.63 1.63 3.13 3.13 3.13 Cylinder Sizing Guide Diameter 1/2 3/4 1-1/16 1-1/2 2 2 1/2 3 4 Rod Diameter 0.31 Rod rea 0.05 0.08 0.31 0.60 0.79 Push rea (Single Rod) 0.20 1.76 3.14 4.91 7.07 12.57 Push rea (Double Rod) 0.15 0.36 0.69 1.45 2.66 4.47 6.47 11.78 Pull rea 0.15 0.36 0.69 1.45 2.66 4.47 6.47 11.78 4 Specifications subject to change without notice or incurring obligation 3-27-02
Standard Series PSD, PSR, PSX, PWD, PTD How to Order Series P - Pancake II Model S - single rod W - double rod T - double rod, hole thru ction D - double acting R - single acting, spring retract (Model S only) X - single acting, spring extend (Model S only) 1-1/2" 2-3/4" 3-1-1/16" 4-1-1/2" 5-2" 6-2-1/2" 7-3" 8-4" Stroke 0.125-1/8" 0-1/4" 0.375-3/8" 0-1/2" etc., thru 4.000-4" (see pages 6 & 7) Model Number Series Model ction Mounting Stroke Options Mounting Counterbored mounting holes are standard in the basic model and need not be specified. For other mounting specify only one option code. CB - Screw clearance holes, both ends 1 CF - Screw clearance holes, front 1 CR - Screw clearance holes, rear 1 F - Nose mount (all except double rod models) 2 HB - Threaded mounting holes, both ends HF - Threaded mounting holes, front HR - Threaded mounting holes, rear PM - Pivot mount, pin 90 from port SM - Pivot mount, pin in-line with port TB - Trunnion mount, both ends 3 TF - Trunnion mount, front 3 TR - Trunnion mount, rear 3 1 Screw clearance to allow bolt head to pass through; No counter bores 2 Includes heavy duty rear head and rod wiper 3 Not available in 1/2" bore. How to Order 1. Specify P, Model, ction, and 2. Specify the Mounting and Stroke 3. Specify the Options in alphabetical order Ordering example: PTD4-HF2.500-TCFV Pancake II with double rod hole thru, double acting, 1-1/2" bore, front threaded mounting holes, 2-1/2" stroke, coarse female rod thread, and Viton seals. Options Enter in alphabetical order B - Bumpers, both ends 1 BF - Bumper, front only 1 BR - Bumper, rear only 1 E - Magnet on piston for position sensing (see length adders page 9) 3/8" stroke minimum 2 H - Heavy duty rear head (see length adder page 9) J - Failsafe operation (single acting, spring retract models) 3 L - Low friction seals (see length adders page 9) M, M1, M3, M4 - Magnet on piston and adhesive mounted dovetail extrusion to hold 1/4" dovetail sensors. (see sensors page 23; length adders page 9) 3/8" stroke min. 2 P2, P3, P4 - Front port position other than standard Q - Low temperature operation ( 40 F to +200 F) TCF - Coarse female rod thread, dimension E (page 7) TCM - Male rod end with coarse thread (page 8) TFM - Male rod end with fine thread (page 8) TN - Non-threaded rod T1, T3, T4 - dditional adhesive mounted dovetail extrusions located in position 1, 3, or 4 V - Viton seals for media compatibility ( 15 F to +225 F) W - Rod wiper, Buna N only (page 8) X - EXTR rod extension Example: X0.5 = 1/2" EXTR Rod Extension X1 = 1" EXTR Rod Extension 1 Stroke is reduced by.03 ;.06 for option B; Spring retracted, BR only; Spring extended, BF only. 2 Not available with Viton seals or low temperature seals. 3 Not available in 1/2" bore. 3-18 -02 Specifications subject to change without notice or incurring obligation 5
Pancake II Cylinders Model PSD Double cting, Single Rod R TYP. Y TYP. 2 C Bolt Circle P Port H F Rod Dia. 1 3 E D - C'd J - Thru Holes 4 places 4 B1* + Stroke 0.13 (2 places at positions 2 & 4 for 1/2" only) *Note: Some options effect cylinder length Standard Strokes ll Models: 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 3-1/2 4 Hole Thru Diameter (PTD) Model PWD Double cting, Double Rod Model PTD Double cting, Hole Thru Double Rod Female Rod Thread 0.14 0.14 0.22 0.28 Male Rod Thread N/ 0.09 0.16 0.31 R TYP. Y TYP. C Bolt Circle 2 F Rod Dia. P Port 1 3 H H E 0.13+ Stroke B2* + Stroke 0.13 D - C'd J - Thru Holes 4 places 4 (2 places at positions 2 & 4 for 1/2" only) *Note: Some options effect cylinder length Hole Thru on PTD Models Dimensions (inches) 1.12 1.50 2.62 3.12 3.75 4.25 5.50 B1* 0.56 0.56 0.94 1.19 1.56 B2* 0.69 0.69 0.94 1.06 1.31 1.69 0-1 0.81 0.81 0.94 1.19 1.56 B3* for Stroke Range 1-2 1.50 1.50 1.56 2.06 2.12 2.44 1-3 1.96 1.94 2.13 2.13 2.19 2.94 3.00 3.31 3.001-4 2.52 2.50 2.75 2.75 2.81 3.81 3.88 4.19 0-1 1.06 1.06 1.44 1.94 2.31 B4* for Stroke Range 1-2 1.62 1.62 2.06 2.81 2.88 3.19 1-3 2.14 2.19 2.63 2.63 2.69 2.81 2.88 3.19 3.001-4 3.21 2.75 3.25 3.25 N N N N C 1.22 1.69 2.19 2.69 3.25 3.78 4.94 D C' 0.20 x 0.13 dp 0.24 x 0.15 dp 0.24 x 0.15 dp 0.34 x 0.22 dp 0.34 x 0.22 dp 0.40 x 0.27 dp 0.40 x 0.27 dp 0.49 x 0.33 dp 6 Specifications subject to change without notice or incurring obligation 3-18-02
Standard Series PSD, PSR, PSX, PWD, PTD Basic Dimensions Model PSR Single cting, Spring Retract R TYP. Y TYP. 2 C Bolt Circle P Port H F Rod Dia. 1 3 See table on page 4 for spring forces D - C'd J - Thru Holes 4 places 4 B3 * + Stroke 0.13 (2 places at positions 2 & 4 for 1/2" only) *Note: Some options effect cylinder length E Standard Strokes ll Models: 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 3-1/2 4 Model PSX Reverse cting, Spring Extend R TYP. Y TYP. C Bolt Circle P Port F Rod Dia. 1 3 2 H See table on page 4 for spring forces B4 * + Stroke 0.13 + Stroke D - C'd J - Thru Holes 4 places 4 (2 places at positions 2 & 4 for 1/2" only) *Note: Some options effect cylinder length E Base 1.15 1.82 4.70 9.22 12.48 21.50 27.74 53.47 pproximate Cylinder Weights (ounces) PSD, PSR, PWD, PTD, PSX PSD, PSR dder per 1/8 of Stroke.06.08.24.32.40.48.64.80 PWD, PTD dder per 1/8 of Stroke Model PWD dder per 1/8 of Stroke for Model PTD PSX dder per 1/8 of Stroke Base Base 1.26*Note:.14 Some options.08effect cylinder length.06 2.03.18.13 1.92.08 5.61.37.25 5.09.24 10.84.55.42 10.08.32 14.71.64.50 13.44.40 27.10.74.59 24.00.48 36.78 1.01.76 31.20.64 69.50 1.20.92 59.33.80 Nose Mount Option dder to Base Weight 0.1 0.2 1.1 1.8 2.7 3.1 3.5 5.9 Dimensions (inches) E Standard #8-32 UNC #10-32 UNF 5/16-24 UNF 3/8-24 UNF 1/2-20 UNF 1/2-20 UNF 5/8-18 UNF 3/4-16 UNF E Coarse N/ #10-24 UNC 5/16-18 UNC 3/8-16 UNC 1/2-13 UNC 1/2-13 UNC 5/8-11 UNC 3/4-10 UNC E Depth for Stroke Range 1/8 1/2 5/8 + 0.30-0.46 0.46 0.30-0.46 0.46 0.37-0.70 0.37-0.70 0.70 0.30-0.70 0.42-0.70 0.70 0.45-0.73 0.73 0.40-0.70 0.80 F 0.31 H 0.22 J Hole 0.13 0.15 0.15 0.20 0.20 0.26 0.26 0.33 P Port #10-32 UNF #10-32 UNF 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 3/8 NPT R 0.34 0.34 0.53 0.66 0.69 0.84 Y 0.14 0.14 0.33 0.33 0.42 3-18-02 Specifications subject to change without notice or incurring obligation 7
Model Options Male Rod Ends (Option TCM or TFM) LT E Thread Pancake II Cylinders Thread Sizes E Thread TCM (Coarse) TFM (Fine) N/ #8-32 UNC #10-24 UNC #10-32 UNF 5/16-18 UNC 5/16-24 UNF 3/8-16 UNC 3/8-24 UNF 1/2-13 UNC 1/2-20 UNF 1/2-13 UNC 1/2-20 UNF 5/8-11 UNC 5/8-18 UNF 3/4-10 UNC 3/4-16 UNF LT Rod Wiper (Option W) Buna-N only BD Boss Dia. BD 0.56 0.69 1.13 1.13 Mounting Options Pivot Mount Complete with bronze pivot bushing. Not available as an accessory. (SM shown) P Diameter for Pivot Pin PR Radius PC Screw Clearance Holes vailable either or both ends. (CR shown) Trunnion Mount vailable rear, front or both. Not available on 1/2" bore. (TF shown solid) TB SC TC TC PF PB PD PE T P PB PC 0.31 Dimensions (inches) PD 0.56 0.56 PE 0.81 1.19 1.31 1.69 1.75 PF 1.88 1.88 PR SC 0.17 0.23 0.34 0.34 0.41 0.41 T N 0.31 TB N 0.125 0 0 0 0.312 0.312 0.375 TC N 0.17 0.33 0.33 0.42 8 Specifications subject to change without notice or incurring obligation 3-18-02
Series PSD, PSR, PSX, PWD, PTD Option Dimensions Deviations from Standard Dimensions (Options L, H, E, M) Length dder (inches) Low Friction Heavy Duty Magnetic Position Sensing (E or M) Seals (L) Rear Head (H) PSD, PWD, PTD PSR PSX 0.13 0.13 Heavy duty rear head is recommended for applications where the cylinder is mounted on the front face or trunnion-mounted, and impact loading (20 or more cycles/minute) occurs between the piston and rear head. It increases the overall length of the cylinder as shown. minimum stroke of 3/8 is required to sense end-of-stroke positions. For low friction seals used in conjunction with magnetic position sensing, use E or M length adder only. Threaded Mounting Holes 1/2" vailable either or both ends. (HR shown) 90 Typ. 3/4" 43 ll others 45 3/4" & Up 90 Typ. Nose Mount vailable on PSD, PSR, and PSX. (F shown) Includes rod wiper and heavy duty rear head. See length adder above. F FF FB FE JJ Hole (2) JJ Hole (4) Threaded 0.13 C Bolt Circle Threaded C Bolt Circle FC FD Thread C 1.22 1.69 2.19 2.69 3.25 3.78 4.94 JJ #4 40 UNC #6 32 UNC # 6 32 UNC # 10 24 UNC # 10 24 UNC 1/4 20 UNC 1/4 20 UNC 5/16 18 UNC Dimensions (inches) F.06.06.13.13.19.25.25.19 FB Hex Hex 1.50 Hex 1.88 Hex 1.88 Hex 1.88 Hex 1.88 Hex 2.62 Hex FC.38.38.75.75.88 1.12 FD 1/2 20 UNF-2 5/8 18 UNF-2 1 14 UNF-2 1-1/4 12 UNF-2 1-3/8 12 UNF-2 1-3/8 12 UNF-2 1-3/8 12 UNF-2 1-3/4 12 UN-2 FE.50.62 1.75 FF.31.25.55.52.52.52.52.88 Maximum Torque for Nose Mount Option Foot-Pounds 12 28 100 120 130 130 130 150 3-4-02 Specifications subject to change without notice or incurring obligation 9
Pancake II Cylinders Nonrotating, double acting 4 sizes 3/4" thru 2" Strokes to 4" standard Twin piston rods are incorporated into the cylinder head to achieve NON-ROTTION. The rods are securely fastened to the piston and tied together externally by a rod end tool bar. The tool bar insures that the rods move in tandem and provides an ideal mounting surface for any attachments required by your application. The tool bar is furnished with threaded mounting holes or optional counter-bored mounting holes. Ratings Standard Units all Series Body......... Self-lubricating composite Heads.... Clear anodized aluminum alloy Tie Bolts............... Stainless steel Rod....... Chrome plated stainless steel Piston................. Stainless steel Rod end.................... Tool bar Ports.................... Position #1 Seals....... Internally lubricated Buna-N Lubrication............. Magnalube -G Rod bushing.................. Bronze Stroke tolerance................. ± 1/64" Media............................ ir Pressure rating, maximum......... 200 psi Minimum recommended operating pressure............. 15 psi Temperature rating Cylinder. 25 to +225 F ( 32 to +121 C) Temperature rating Electronic sensors...... 4 to +176 F ( 20 to +80 C) llowable Torsion Load and Rotational Tolerance Side loading should be avoided for any cylinder application. The smaller diameter twin rods will have more deflection due to side load than the one standard rod in a comparable Pancake II cylinder. However, the PND Series is designed to work satisfactorily against pure torsional loads. Maximum torsional load per bore size is shown in the following table. ngular Deflection pproximate ngular Deflection (Degrees) due to max. torsional load Torsional Stroke Load Max. 0 to 1-1/2 2 2-1/2 3 3-1/2 4 3/4 0.3 less than 0.22 0.51 0.98 1.67 2.62 3.88 1-1/16 1.0 less than 0.15 0.33 0.64 1.09 1.71 2.53 1-1/2 5.0 less than 0.08 0.18 0.36 0.61 0.95 1.41 2 10.0 less than 0.03 0.07 0.13 0.22 0.34 Freeplay Rotational Tolerance 3/4" (2) 1-1/16" (3) 1-1/2" (4) 2" (5) Max. Rotation ±1 ±3/4 ±1/2 ±1/2 10 Cylinder Sizing Guide Diameter Rod Diameter Rod rea 0.05 0.10 0.22 Push rea 1.76 3.14 Pull rea 0.39 0.78 1.54 2.76 Specifications subject to change without notice or incurring obligation 3-5-02
Nonrotating, Twin Rod Series PND How to Order Series P - Pancake II Model N - Nonrotating, Twin Rod ction D - double acting 2-3/4" 3-1-1/16" 4-1-1/2" 5-2" Stroke 0.125-1/8" 0-1/4" 0.375-3/8" 0-1/2" etc., thru 4.000-4" (see page 12) Model Number Series Model ction Mounting Stroke Options Mounting Counterbored mounting holes are standard in the basic model and need not be specified. For other mounting specify only one option code. CB - Screw clearance holes, both ends 1 CF - Screw clearance holes, front 1 CR - Screw clearance holes, rear 1 HB - Threaded mounting holes, both ends HF - Threaded mounting holes, front HR - Threaded mounting holes, rear PM - Pivot mount, pin 90 from port SM - Pivot mount, pin in-line with port TB - Trunnion mount, both ends TF - Trunnion mount, front TR - Trunnion mount, rear 1 Screw clearance to allow bolt head to pass through; No counter bores Options Enter in alphabetical order CE - Counterbored rod end tool bar (page 12) E - Magnet on piston for position sensing ( length adder) 3/8" stroke minimum 1 K - Rod end tool bar rotated 90 M, M1, M3, M4 - Magnet on piston and adhesive mounted dovetail extrusion to hold 1/4" dovetail sensors. (see sensors page 23; length adder) 3/8" stroke minimum 1 P2, P3, P4 - Front port position other than standard (page 12) Q - Low temperature operation ( 40 F to +200 F) T1, T3, T4 - dditional adhesive mounted dovetail extrusions located in position 1, 3, or 4 V - Viton seals for media compatibility ( 15 F to +225 F) X - EXTR rod extension Example: X0.5 = 1/2" EXTR Rod Extension X1 = 1" EXTR Rod Extension 1 Not available with Viton seals or low temperature seals. How to Order 1. Specify P, Model, ction and 2. Specify the Mounting and Stroke 3. Specify the Options in alphabetical order Ordering example: PND3-PM0.375-CE This model number specifies a nonrotating, double acting, cylinder with tool bar, 1-1/16" bore, pivot mounting, 3/8" stroke and counterbored rod end tool bar. 3-18-02 Specifications subject to change without notice or incurring obligation 11
Pancake II Cylinders Basic Model PND Twin Rod, Nonrotating Double cting RR YY R Y NM C Bolt Circle P Port NL N 2 F Rod Dia. 1 H 3 B + Stroke See Note 1 N.07 D - C'd J - Thru Holes 4 places 4 E Thread 2 Places Note 1: Magnetic Position Sensing Length dder = minimum stroke of 3/8" is required to sense end-of-stroke positions Standard Strokes ll Models: 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 3-1/2 4 Longer strokes available. Contact Engineering or your local Fabco-ir distributor for information. Counterbored Rod End Tool Bar Option CE E -C'd K -Thru Hole 2 places NM.07 NL C' Hole Dimensions (inches) E C' 0.24 x 0.15 dp 0.29 x 0.18 dp 0.40 x 0.27 dp 0.49 x 0.33 dp K 0.15 0.18 0.26 0.33 N Dimensions (inches) 1.50 2.62 3.12 B 0.94 1.31 1.31 C 1.22 1.69 2.19 2.69 D 0.24 x 0.15 dp 0.24 x 0.15 dp 0.34 x 0.22 dp 0.34 x 0.22 dp E Thread #6-32 UNC #8-32 UNC 1/4-20 UNC 5/16-18 UNC F H 0.332 0.422 0.562 0 N NL 1.44 2.50 NM 1.06 1.50 1.88 P #10-32 UNF 1/8 NPT 1/8 NPT 1/8 NPT R 0.34 0.53 RR 0.47 0.69 0.69 0.72 Y 0.14 YY 0.27 12 Specifications subject to change without notice or incurring obligation 3-18-02
Nonrotating Series PND Dimensions & Options Mounting Options Trunnion Mount vailable rear, front or both. (TF shown solid) TC TB TC Pivot Mount Complete with bronze pivot bushing. Not available as an accessory. (SM shown) P Diameter for Pivot Pin PR Radius PC PF T PB PD PE Threaded Mounting Holes vailable either or both ends. (HR shown) 90 Typ. Screw Clearance Holes vailable either or both ends. (CR shown) 3/4" 43 ll others 45 SC JJ Hole (4) Threaded C Bolt Circle pproximate Cylinder Weights (ounces) Base 3.1 7.4 14.3 21.5 dder per 1/8 of Stroke 0.1 0.5 0.7 0.9 Dimensions (inches) C 1.22 1.69 2.19 2.69 JJ #6-32 UNC #6-32 UNC #10-24 UNC #10-24 UNC P PB PC 0.31 PD PE 0.81 1.19 PF PR SC 0.23 0.34 0.34 T 0.31 TB 0.125 0 0 0 TC 0.17 3-18-02 Specifications subject to change without notice or incurring obligation 13
Pancake II Cylinders Double acting, single rod end Cylinders multiply force output 3 sizes 2-1/2" thru 4" Strokes to 4" standard ir Exhaust ir Exhaust ir Exhaust ir Exhaust Shop ir Supply to Extend Port How it Works Fabco-ir attaches multiple pistons to a common shaft and provides internal air passages through the shaft to all pistons. When air pressure is applied to the extend port, all pistons are pressurized simultaneously, enabling tremendous thrust forces to be obtained. (See the handy cylinder sizing guide below for the force multiplying factors.) When air pressure is applied to the retract port only one piston is pressurized. Body Self-lubricating composite Head... Clear anodized aluminum alloy Tie Bolts... Stainless steel Rod... Chrome plated stainless steel Piston... luminum alloy Rod end... Female thread with wrench flats Ports... Position #1 Seals...Internally lubricated Buna-N Lubrication... Magnalube -G Rod bushing... PTFE composite bearing Ratings Standard Units all Series Extend Port - ir supplied to all pistons Shop ir Supply to Retract Port ir Intake ir Intake ir Intake ir Exhaust Retract Port - ir supplied to front piston only Stroke tolerance......... ± 1/64" per stage Media............................ ir Pressure rating, maximum......... 200 psi Minimum recommended operating pressure............. 15 psi Temperature rating Cylinder............. 25 to +225 F ( 32 to +121 C) Temperature rating Electronic sensors...... 4 to +176 F ( 20 to +80 C) Cylinder Sizing Guide 14 2-1/2 3 4 Model Designation 6 7 8 PM2 9.4 13.5 24.3 Extend Power Factor 13.8 20.0 36.1 18.3 26.5 47.9 Specifications subject to change without notice or incurring obligation Retract Power Factor 4.5 6.5 11.8 3-18-02
Multi-Power Series PM2, & How to Order Series P - Pancake II Multi-Power Model and ction M2-2 stage extend, single stage retract M3-3 stage extend, single stage retract M4-4 stage extend, single stage retract 6-2-1/2" 7-3" 8-4" Stroke 0.125-1/8" 0-1/4" 0.375-3/8" 0-1/2" etc., thru 4.000-4" (see page 16) Model Number Series Model ction Mounting Stroke Options Options Enter in alphabetical order Mounting Counterbored mounting holes are standard in the basic model and need not be specified. For other mounting specify only one option code. CB - Screw clearance holes, both ends 1 CF - Screw clearance holes, front 1 CR - Screw clearance holes, rear 1 HB - Threaded mounting holes, both ends HF - Threaded mounting holes, front HR - Threaded mounting holes, rear 1 Screw clearance to allow bolt head to pass through; No counter bores E - Magnet on piston for position sensing (see length adders page 17) 3/8" stroke minimum 1 L - Low friction seals (see length adders page 17) M, M1, M3, M4 - Magnet on piston and adhesive mounted dovetail extrusion to hold 1/4" dovetail sensors. (see sensors page 23; length adders page 17) 3/8" stroke min. 1 P2, P3, P4 - Front port position other than standard (page 16) P6, P7, P8 - Rear port position other than standard (page 16) Q - Low temperature operation ( 40 F to +200 F) TCF - Coarse female rod thread, dimension E (page 16) TCM - Male rod end with coarse thread (page 17) TFM - Male rod end with fine thread (page 17) TN - Non-threaded rod T1, T3, T4 - dditional adhesive mounted dovetail extrusions located in position 1, 3, or 4 V - Viton seals for media compatibility ( 15 F to +225 F) W - Rod wiper, Buna N only (page 17) X - EXTR rod extension Example: X0.5 = 1/2" EXTR Rod Extension X1 = 1" EXTR Rod Extension 1 Not available with Viton seals or low temperature seals. How to Order 1. Specify P, Model, ction and 2. Specify the Mounting and Stroke 3. Specify the Options in alphabetical order Ordering example: 7-HB0-TCFV This model number specifies a Multi-Power, 3 stage extend, 1 stage retract, 3" bore cylinder, threaded mounting holes on both ends, 1" stroke, with coarse female rod thread and Viton seals. 3-18-02 Specifications subject to change without notice or incurring obligation 15
Model PM2 6 7 5 Pancake II Cylinders Standard Strokes ll Models: 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 3-1/2 4 Special strokes available on request. Contact Engineering or your local Fabco-ir Distributor Port RR B* + (2 x Stroke) Vent R Typ 0.13 Port F Rod Dia. C Bolt Circle P Port 1 3 2 H E Model 8 YY Y D - C'd J - Thru Holes 4 places Standard Strokes ll Models: 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 3-1/2 4 Special strokes available on request. Contact Engineering or your local Fabco-ir Distributor 4 D - C'd J - Thru Holes 4 Places (2-1/2" ) 6 Places (3" & 4" s) Both Ends 6 Port RR B* + (3 x Stroke) Vents R Typ 0.13 Port C Bolt Circle 2 7 5 P Port F Rod Dia. H 1 3 E Model D - C'd J - Thru Holes 4 Places (2-1/2" ) 6 Places (3" & 4" s) Both Ends 8 6 Port 7 5 RR YY Standard Strokes ll Models: 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 1-3/4 2 2-1/2 3 3-1/2 4 Special strokes available on request. Contact Engineering or your local Fabco-ir Distributor Vents B* + (4 x Stroke) Y R Typ 0.13 Port F Rod Dia. C Bolt Circle P Port 1 3 4 2 H E 8 YY Y 4 *Dimension B for Strokes.125,.188, and.250 PM2 2.65 2.75 3.38.125 Stroke 3.64 3.77 4.61 4.63 4.79 5.85 PM2 2.71 2.81 3.44.188 Stroke 3.76 3.90 4.74 4.81 4.98 6.04 PM2 2.77 2.88 3.53.250 Stroke 3.87 4.01 4.89 4.97 5.15 6.24 Dimensions (inches) 3.75 4.25 5.50 B* (strokes over.250) PM2 2.29 2.39 3.04 3.15 3.28 4.15 4.02 4.18 5.27 C 3.25 3.78 4.94 D C' 0.40 x 0.27 dp 0.40 x 0.27 dp 0.49 x 0.33 dp E Female Thread E Standard E Course 1/2-20 UNF 1/2-13 UNC 5/8-18 UNF 5/8-11 UNC 3/4-16 UNF 3/4-10 UNC E Depth for Stroke Range 1/8 1/2 5/8 + 0.42-0.70 0.70 0.45-0.73 0.73 0.40-0.70 0.80 F H J 0.26 0.26 0.33 P 1/4 NPT 1/4 NPT 3/8 NPT R 0.66 0.69 0.84 RR 0.91 0.94 1.22 Y 0.33 0.33 0.42 YY 0.58 0.58 0.80 16 Specifications subject to change without notice or incurring obligation 3-28-02
Multi-Power Series PM2, & Models & Options Mounting Options Threaded Mounting Holes vailable either or both ends. (HR shown) 90 Typ. Screw Clearance Holes vailable either or both ends. (CR shown) Screw clearance holes are standard on all center sections. SC Dia 4 Places 6 Places ( & 3" & 4" s) 45 C Bolt Circle JJ Threaded Hole 4 Places 6 Places ( & 3" & 4" s) Model Options Male Rod Ends (Option TCM or TFM) (Model PM2 shown) Rod Wiper (Option W) Buna-N only. (Model PM2 shown) LT BD E Thread pproximate Cylinder Weights (ounces) Base 37.2 49.9 93.1 BD 1.13 PM2 dder per 1/8 Stroke 1.2 1.6 2.0 C 3.25 3.78 4.94 Base 53.3 71.0 133.8 dder per 1/8 Stroke 1.8 2.4 3.0 Base 69.4 92.1 174.5 Dimensions (inches) JJ 1/4 20 UNC 1/4 20 UNC 5/16 18 UNC E Male Thread TCM (Coarse) 1/2-13 UNC 5/8-11 UNC 3/4-10 UNC dder per 1/8 Stroke 2.4 3.2 4.0 TFM (Fine) 1/2-20 UNF 5/8-18 UNF 3/4-16 UNF LT SC 0.41 0.41 2-1/2 3 4 Length dder for Options (inches) Series PM2 PM2 PM2 Low Friction Seals (L) 1.13 1.50 1.50 1.50 Magnetic Position Sensing (E or M) Low Friction Seals & Magnetic Position Sensing (EL or LM) 1.63 1.88 2.38 1.88 2.38 1) minimum stroke of 3/8" is required to sense end-of-stroke positions. 2) Magnet is applied to front piston. 3-18-02 Specifications subject to change without notice or incurring obligation 17
Pancake II Cylinders Double acting, single rod end Cylinder provides 3 positions 8 sizes 1/2" thru 4" Strokes to 4" standard Other multi-position cylinders (4 position, 5 position, etc.) are available as specials. Contact Engineering or your local Fabco-ir distributor for more information. Body......... Self-lubricating composite Heads.... Clear anodized aluminum alloy Tie Bolts............... Stainless steel Rod....... Chrome plated stainless steel Piston................ luminum alloy Rod end... Female thread & wrench flats Ports.................... Position #1 Seals....... Internally lubricated Buna-N Lubrication............. Magnalube -G Rod bushing... PTFE composite bearing Ratings Standard Units all Series Stroke tolerance........ ± 1/64" per stroke Media............................ ir Pressure rating, maximum......... 200 psi Minimum recommended operating pressure............. 15 psi Temperature rating Cylinder. 25 to +225 F ( 32 to +121 C) Temperature rating Electronic sensors...... 4 to +176 F ( 20 to +80 C) Cylinder Sizing Guide Diameter 1/2 3/4 1-1/16 1-1/2 2 2 1/2 3 4 Rod Diameter 0.31 Rod rea 0.05 0.08 0.31 0.60 0.79 Push rea 0.20 1.76 3.14 4.91 7.07 12.57 Pull rea 0.15 0.36 0.69 1.45 2.66 4.47 6.47 11.78 How it Works Position 1 ir is supplied to port C. Both pistons retract. Position 2 ir is supplied to port. Piston extends fully. Piston B extends partially. Stroke Stroke B Position 3 ir is supplied to port B Piston B extends fully. B ir in Port C B Stroke B B Stroke ir in Port B 18 ir in Port Specifications subject to change without notice or incurring obligation 3-28-02
Multi-Position Series P3D How to Order Series P - Pancake II Model and ction 3D - 3 position, double acting 1-1/2" 2-3/4" 3-1-1/16" 4-1-1/2" 5-2" 6-2-1/2" 7-3" 8-4" Stroke 0.125-1/8" 0-1/4" 0.375-3/8" 0-1/2" etc., thru 4.000-4" Stroke B 0.125-1/8" 0-1/4" 0.375-3/8" 0-1/2" etc., thru 4.000-4" See page 20 for minimum stroke lengths. Model Number Series Model ction Mounting Stroke / StrokeB Options Mounting Counterbored mounting holes are standard in the basic model and need not be specified. For other mounting specify only one option code. CB - Screw clearance holes, both ends 1 CF - Screw clearance holes, front 1 CR - Screw clearance holes, rear 1 HB - Threaded mounting holes, both ends HF - Threaded mounting holes, front HR - Threaded mounting holes, rear PM - Pivot mount, pin 90 from port SM - Pivot mount, pin in-line with port 1 Screw clearance to allow bolt head to pass through; No counter bores Options Enter in alphabetical order E - Magnet on rod end piston for position sensing (see length adders page 20) 3/8" stroke minimum 1 L - Low friction seals (see length adders page 20) M, M1, M3, M4 - Magnet on piston and adhesive mounted dovetail extrusion to hold 1/4" dovetail sensors. (see sensors page 23; length adders page 20) 3/8" stroke min. 1 P2, P3, P4 - Front port position other than standard (page 20) P6, P7, P8 - Rear port position other than standard (page 20) Q - Low temperature operation ( 40 F to +200 F) TCF - Coarse female rod thread, dimension E (page 20) TCM - Male rod end with coarse thread (page 20) TFM - Male rod end with fine thread (page 20) TN - Non-threaded rod T1, T3, T4 - dditional adhesive mounted dovetail extrusions located in position 1, 3, or 4 V - Viton seals for media compatibility ( 15 F to +225 F) W - Rod wiper, Buna N only (page 20) X - EXTR rod extension Example: X0.5 = 1/2" EXTR Rod Extension X1 = 1" EXTR Rod Extension 1 Not available with Viton seals or low temperature seals. How to Order 1. Specify P, Model, ction and 2. Specify the Mounting and Stroke 3. Specify the Options desired Ordering example: P3D5-CR0.375/0-TCM This model number specifies a 3-position, double acting, cylinder, 2" bore, screw clearance holes at rear, 3/8" stroke, 2" stroke B, and male rod end with coarse thread. 3-18-02 Specifications subject to change without notice or incurring obligation 19
Basic Model 6 7 5 8 Pancake II Cylinders Stroke (2 x Stroke + Stroke B + Ba) RR R YY Stroke B B Y 0.13 C Bolt Circle E Rod Thread H P Port F Rod Dia. 1 3 D - C'd 4 J - Thru Holes 4 places (2 places at positions 2 & 4 for 1/2" only) 2 Minimum Stroke* Base Model Stroke 0.34 *Note: 1) No minimum for stroke B. 2) No minimum for stroke or B with Low Friction Option -L Model Options Rod Wiper (Option W) Buna-N only. Deviations from Standard Dimensions (Options L, E, M) B B LT BD Male Rod Ends (Option TCF or TFM) E Thread Low Friction Seals (L) Length dder (inches) Magnetic Position Sensing (E or M) 1) minimum stroke of 3/8" is required to sense end-of-stroke positions. 2) Magnet is applied to piston of stroke B. Low Friction Seals & Magnetic Position Sensing (EL or LM) 1.12 1.12 1.12 1.50 2.62 3.12 3.75 4.25 5.50 Ba 1.14 1.14 1.67 1.70 1.80 2.25 2.34 3.00 BD 0.56 0.69 1.13 1.13 C 1.22 1.69 2.19 2.69 3.25 3.78 4.94 D C' 0.20 x 0.13 dp 0.24 x 0.15 dp 0.24 x 0.15 dp 0.34 x 0.22 dp 0.34 x 0.22 dp 0.40 x 0.27 dp 0.40 x 0.27 dp 0.49 x 0.33 dp E Female Thread E Standard #8-32 UNC #10-32 UNF 5/16-24 UNF 3/8-24 UNF 1/2-20 UNF 1/2-20 UNF 5/8-18 UNF 3/4-16 UNF Dimensions (inches) E Course N/ #10-24 UNC 5/16-18 UNC 3/8-16 UNC 1/2-13 UNC 1/2-13 UNC 5/8-11 UNC 3/4-10 UNC E Depth for Stroke Range 1/8 1/2 5/8 + 0.30-0.46 0.46 0.30-0.46 0.46 0.37-0.70 0.37-0.70 0.70 0.30-0.70 0.42-0.70 0.70 0.45-0.73 0.73 0.40-0.70 0.80 F 0.31 H 0.22 J 0.13 0.15 0.15 0.20 0.20 0.26 0.26 0.33 LT P #10-32 UNF #10-32 UNF 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 3/8 NPT R 0.34 0.34 0.53 0.66 0.69 0.84 RR 0.47 0.47 0.69 0.69 0.72 0.91 0.94 1.22 Y 0.14 0.14 0.33 0.33 0.42 YY 0.27 0.27 0.58 0.58 0.80 20 Specifications subject to change without notice or incurring obligation 3-22-02
Multi-Position Series P3D Models & Options Mounting Options Threaded Mounting Holes vailable either or both ends. (HR shown) 1/2 Screw Clearance Holes vailable either or both ends. (CR shown) Screw clearance holes are standard on all center sections. SC 90 Typ. C Bolt Circle JJ Hole (2) Threaded 3/4 & Up 90 Typ. Pivot Mount Complete with bronze pivot bushing. (SM shown) Not available as an accessory 3/4" 43 ll others 45 P Diameter for Pivot Pin PR Radius PC JJ Hole (4) Threaded C Bolt Circle PF PB PD PE ) C 1.22 1.69 2.19 2.69 3.25 3.78 4.94 JJ #4-40 UNC #6-32 UNC #6-32 UNC #10-24 UNC #10-24 UNC 1/4-20 UNC 1/4-20 UNC 5/16-18 UNC Dimensions (inches) P PB PC 0.31 PD 0.56 0.56 PE 0.81 1.19 1.31 1.69 1.75 PF 1.88 1.88 PR SC 0.17 0.23 0.34 0.34 0.41 0.41 pproximate Cylinder Weights (ounces) 1/2 (02) 3/4 (04) 1-1/16 (09) 1-1/2 (17) 2 (31) 2-1/2 (50) 3 (70) 4 (125) Base 3.3 4.5 9.9 18.7 24.5 41.3 52.9 102.7 dder per 1/8 of Stroke 0.16 0.2 0.6 0.8 1.0 1.2 1.6 2.0 3-18-02 Specifications subject to change without notice or incurring obligation 21
Pancake II Cylinders ccessories ccessory Clevis Bracket Trunnion Bracket Rod Eye Standard Series Selection Guide PND Series N/ Multi-Power Series N/ N/ P3D Series N/ Clevis Bracket nodized aluminum alloy Chrome plated steel pin included J H I E Pin Dia. x F Long C L Hole for N Bolt Square D K Square The bracket is intended for mounting with either a rod pivot or pivot mount; it is not intended to mount directly with the rear cylinder head. Kit No. CB-3 CB-6 CB-8 1.75 2.50 Dimensions (inches) C D E F H I 0.71 1.37 2.10 0.39 0.187 0.93 0.16 0.56 0.375 1.63 0.22 0.94 0.625 2.42 J K 0.78 1.34 1.81 L 0.42 0.80 1.19 N #6 #10 1/4 Trunnion Bracket (pair) nodized aluminum alloy complete with bronze pivot bushings E Hole Dia. H W I IH K J Hole for N Bolt Kit No. TB-2 TB-5 TB-7 TB-8 H Dimensions (inches) W 0.31 E 0.126 1 0.313 0.376 I 0.22 0.31 IH 0.30 0.45 0.55 J 1.12 1.50 1.63 1.88 K 0.56 0.81 0.94 1.06 N #10 1/4 5/16 3/8 Rod Eye Steel with bronze pivot bushing and nut P Thread J LT I JT C C L E Hole Dia. Kit No. RE-1 RE-2 RE-3 RE-4 RE-6 RE-7 RE-8 C Dimensions (inches) E 0.187 0.187 0.187 0.375 0.375 0.625 0.625 I 0.47 0.47 0.47 0.72 0.72 J 0.72 0.72 0.72 1.16 1.16 1.63 1.63 JT L 0.32 0.32 0.32 0.58 0.58 0.80 0.80 LT P #8-32 UNC #10-32 UNF 5/16-24 UNF 3/8-24 UNF 1/2-20 UNF 5/8-18 UNF 3/4-16 UNF 22 Specifications subject to change without notice or incurring obligation 3-22-02
Position Sensing Sensor Specifications & Ordering Information Slotted Set Screw Encased in a plastic housing, dovetail style electronic sensors are corrosion resistant. 45 wire outlet allows close mounting. Two methods of mounting are available: 1. Tie bolt spacer mounted clamps (Option -E) 2. dhesive mounted dovetail extrusions (Option -M) Order sensors separately from the table below Sensor Pigtail 34 (1.34) 8.5 (.33) 1, 2 or 5 Meter Cable 32 (1.26) 9.8 (.39) Ordering Guide Dovetail Style Magnetic Sensor with LED Sensor Type Electronic Electronic Prewired 9 ft. Part No. 949-000-031 949-000-032 Quick Disconnect Part No.* 949-000-331 949-000-332 Wire Leads 3 3 Sensor Temperature Range -20 to +80 C (-4 to +176 F) Electrical Characteristics Sourcing PNP 6-24 VDC, 0.20 mp Max current, 0.5 Voltage Drop Sinking NPN 6-24 VDC, 0.20 mp Max current, 0.5 Voltage Drop Note*: Quick disconnect styles are supplied with 6 inch pigtail with male connector. Order female cordsets separately. Option -E Magnet on piston use spacer mounted clamps Female Cordsets for Quick Disconnect Length 1 Meter 2 Meters 5 Meters Part No. CFC-1M CFC-2M CFC-5M Tie Bolt Spacer. Dovetail style sensor Clamp (tinted blue for illustration purposes) To apply dovetail style sensors first locate clamp in rough position on any of the tie bolt spacers and lock it in place with the set screw. Clamp Selection Guide Kit No. SC-1 SC-2 SC-3 SC-5 SC-7 SC-8 To Fit 1/2 3/4 1-1/16 1-1/2 & 2 2-1/2 & 3 4 Next, make fine adjustment by sliding the sensor within the clamp and lock in place with its slotted set screw. Order clamps and sensors separately Option -M Magnet on piston and adhesive mounted dovetail extrusions Dovetail Extrusion (tinted blue for illustration purposes) Dovetail style sensor Order sensors separately Specify Option M for mounting rail(s) located in standard position(2). 1 3 Specify option M1, M3, or M4 for mounting rail in alternate positions 1, 3, or 4 respectively. dditional dovetail rails may be applied by specifying options T1, T3, or T4. The design and construction of the Pancake II allows the cylinder barrel to float approximately 0.020 axially. It can also rotate slightly. The axial movement will be more noticeable than the rotational movement during cylinder cycling and may present what appears to be sensor 2 4 Standard Dovetail Rail Positions Stroke Range Position 1/2" 3/8" to 1-1/4" 1 & 3 1/2" 1-1/2" & above 1 3/4" 3/8" to 1-1/4" 2 & 4 3/4" 1-1/2" & above 2 1-1/16" & up 3/8" & above 2 Note: When alternate positions are specified, the second of two required dovetail rails will be applied at position 2. (Contact factory for other combinations.) malfunction when using the extruded dovetail rail. Thus, for extremely precise sensor applications where this may be troublesome, it is recommended to use the spacer-mounted clamps shown above in the -E option to provide a more stable and rigid sensor mount. 3-18-02 Specifications subject to change without notice or incurring obligation 23
Pancake II Cylinders Prices effective ugust 15, 2005 List Prices - Series PSD, PSR, PSX, PWD, PTD Base Price by Size Basic Model PSD PSR (0 to 1" Stroke) PSR (1-1/8 to 4" Stroke) PSX (0 to 1" Stroke) PSX (1-1/8 to 4" Stroke) dd per 1/8" of Stroke (PSD, PSR, PSX) PWD dd per 1/8" of Stroke PTD dd per 1/8" of Stroke $34.55 37.00 40.55 44.40 45.40 0.20 50.10 54.35 $35.65 39.35 41.85 45.75 47.00 0.20 51.55 56.10 $46.30 5 54.15 58.20 59.45 0.30 64.80 0.35 70.00 0.35 $55.05 59.05 63.50 70.00 74.45 0.40 79.70 0.60 84.90 0.60 $63.45 67.90 72.40 78.95 83.35 0.60 91.60 0.80 99.10 0.80 $80.60 86.20 93.60 97.85 105.20 0.80 113.40 0.90 120.90 0.90 $99.25 106.25 113.60 118.40 125.75 0.85 136.55 145.05 $146.15 157.25 164.60 175.40 18 1.05 193.65 1.30 204.55 1.30 dders by Size Mounting Options CB, CF, CR (Screw Clearance Holes) F (Nose Mount) HB, HF, HR (Threaded Mounting Holes) PM, SM (Pivot Mount) TB, TF, TR (Trunnion Mount) 2.15 4.95 2.55 9.85 N 2.25 5.70 2.65 10.40 8.60 2.25 19.15 2.85 1 8.60 2.25 21.30 3.55 16.35 8.60 2.25 27.30 3.55 19.00 8.60 2.25 30.05 4.15 24.45 9.80 2.25 31.95 4.15 29.40 9.80 2.25 42.45 5.10 40.20 10.35 Options No charge for Options H, P2, P3, P4, TCF, TN B (both ends) BF (front only) BR (rear only) E (Magnetic Piston Sensing) J (with Standard Seals) J (with Viton Seals) L (Low Friction Seals) M, M1, M3, M4 (Mag. Piston Sensing) Q (Low Temperature Seals) Single cting Reverse cting Double cting Double End Rod Q (Low Temp. Seals with L Option) Single cting Reverse cting Double cting Double End Rod TCM, TFM (Male Rod Thread each end) T1, T3, T4 (Switch Mounting Rail per rail) V (with Standard Seals) Single cting Reverse cting Double cting Double End Rod V (with Low Friction Seals) Single cting Reverse cting Double cting Double End Rod W (Rod Wiper single end) W (Rod Wiper double end) X (each 1/2" or fraction thereof - each end) 8.75 5.45 3.30 4.05 N N 2.90 5.35 1.80 2.05 2.10 2.60 3.90 4.35 4.45 5.60 3.45 1.65 2.25 3.35 4.05 4.80 5.40 9.70 1 5.95 11.95 0.55 8.75 5.45 3.30 4.05 0.10 0.40 3.00 5.35 2.30 2.55 2.60 3.30 4.95 5.45 5.60 7.00 3.60 1.70 2.50 3.55 4.20 4.95 5.55 9.90 10.45 6.35 12.60 0.55 18.55 13.10 5.45 4.05 0.15 0.60 3.70 5.35 2.85 3.15 3.30 4.10 6.15 6.80 7.00 8.85 4.00 2.60 3.00 4.00 5.20 6.25 8.30 9.30 15.75 16.75 7.75 15.55 0.70 dders by Size 18.55 13.10 5.45 5.95 0.15 0.60 4.15 7.90 3.60 3.95 4.10 5.15 7.70 8.50 8.85 11.10 4.35 2.60 5.00 6.20 8.30 9.45 10.40 11.80 19.60 20.80 8.25 16.35 0.85 24.60 19.15 5.45 10.00 0.20 0.80 4.95 13.25 4.45 4.95 5.15 6.45 9.60 10.60 11.10 13.80 6.10 2.60 6.65 7.90 10.95 12.20 16.80 18.00 31.20 32.50 9.70 19.35 1.05 24.85 19.15 5.70 13.30 0.20 0.80 6.05 19.80 5.60 6.20 6.45 8.05 12.05 13.30 13.90 17.30 6.10 3.20 9.60 1 14.90 16.10 21.65 22.90 39.40 40.55 10.30 20.55 1.05 24.85 19.15 5.70 17.45 0.20 0.95 7.00 23.85 7.00 7.75 8.05 10.10 15.10 16.65 17.30 21.70 7.20 3.20 13.30 14.85 21.90 23.55 24.85 27.00 46.20 47.80 11.85 23.75 1.15 4 30.60 10.40 19.75 2.60 8.30 26.35 8.80 9.65 10.10 12.65 18.90 20.80 21.70 27.15 8.60 3.20 18.20 19.80 27.40 29.20 32.25 33.85 55.60 57.20 12.50 25.05 1.50 24 Specifications subject to change without notice or incurring obligation 8-4-05
List Prices Prices effective ugust 15, 2005 List Prices - Nonrotating Series PND Basic Model PND dder per 1/8" of stroke $53.30 Base Price by Size $69.90 0.35 $82.85 0.55 $95.70 0.70 Mounting Options CB,CF, CR (Screw Clearance Holes) HB, HF, HR (Threaded Mounting Holes) PM, SM (Pivot Mount) TB, TF, TR (Trunnion Mount) $2.25 2.65 10.40 8.60 dders by Size $2.25 2.85 1 8.60 $2.25 3.55 16.35 8.60 $2.25 3.55 19.00 8.60 Options No charge for Options CE, K, P2, P3, P4 E (Magnetic Piston Sensing) M, M1, M3, M4 (Mag. Piston Sensing) Q (Low temperature seals) T1, T3, T4 (Switch mounting rail per rail) V (Viton Seals) X (each 1/2" or fraction thereof) $4.05 5.35 4.60 1 0.55 dders by Size $4.05 5.35 5.70 2.60 17.00 0.70 $5.95 7.90 7.20 2.60 21.10 0.80 $10.00 13.25 9.00 2.60 32.90 1.05 List Prices - Multi-Power Series PM2,, 8-4-05 Basic Model PM2 dd per 1/8" of Stroke dd per 1/8" of Stroke dd per 1/8" of Stroke Mounting Options CB, CF, CR (Screw Clearance Holes) HB, HF, HR (Threaded Mounting Holes) Base Price by Size $132.95 2.30 19 3.45 233.25 4.20 $166.20 2.90 277.85 3.85 277.95 4.65 $241.30 3.50 303.40 4.35 370.80 5.20 dders by Size $2.25 4.15 $2.25 4.15 $2.25 5.10 Options No charge for Options P2 thru P8, TCF, TN, E (Magnetic Piston Sensing) L (Low Friction Seals) PM2 M, M1, M3, M4 (Mag. Piston Sensing) Q (Low Temperature Seals) PM2 Q (Low Temperature Seals with L Option) PM2 TCM, TFM (Male Rod Thread) T1, T3, T4 (Switch Mounting Rail per rail) PM2 V (Viton Seals) V (Viton Seals with L Option) PM2 W (Rod Wiper) X (Rod extension each 1/2" or fraction thereof) dders by Size $13.30 11.65 17.40 23.25 19.80 11.30 19.75 34.60 24.30 42.50 74.35 6.10 3.20 18.60 27.90 37.25 49.25 73.90 98.50 10.30 1.05 $17.45 13.50 20.35 27.10 23.85 14.10 24.65 43.15 30.30 53.05 92.80 7.20 3.20 27.30 4 54.60 57.75 86.65 115.55 11.85 1.15 $19.75 15.75 23.65 31.55 26.35 17.70 30.95 54.15 37.95 66.45 116.30 8.60 3.20 34.25 51.45 68.60 69.50 104.20 139.00 12.50 1.50 Specifications subject to change without notice or incurring obligation 25
Pancake II Cylinders List Prices - Multi-Position Series P3D Basic Model P3D Total combined stroke adder (per 1/8") $58.20 Total combined stroke = (2 x Stroke ) + Stroke B Prices effective ugust 15, 2005 $61.15 $74.45 0.35 Base Price by Size $88.15 $101.10 $124.80 0.85 $170.10 0.95 List Prices $226.50 1.05 dders by Size Mounting Options CB, CF, CR(Screw Clearance Holes) HB, HF, HR (Threaded Mounting Holes) PM, SM (Pivot Mount) $2.15 2.55 9.85 $2.25 2.65 10.40 $2.25 2.85 1 $2.25 3.55 16.35 $2.25 3.55 19.00 $2.25 4.15 24.45 $2.25 4.15 29.40 $2.25 5.10 40.20 Options No charge for Options P2 thru P8, TCF, TN E (Magnetic Piston Sensing) L (Low Friction Seals) M, M1, M3, M4 (Mag. Piston Sensing) Q (Low Temperature Seals) Q (with Low Friction Seals) TCM, TFM (Male Rod Thread) T1, T3, T4 (Switch Mounting Rail per rail) V (with Standard Seals) V (with Low Friction Seals) W (Rod Wiper) X (each 1/2" or fraction thereof) $4.05 5.60 5.35 4.15 8.95 3.45 4.25 12.45 5.95 0.55 $4.05 5.90 5.35 5.20 1 3.60 4.50 12.70 1.05 0.55 $4.05 7.35 5.35 6.55 14.05 4.00 2.60 6.65 20.30 7.75 0.70 dders by Size $5.95 8.25 7.90 8.20 17.70 4.35 2.60 10.60 25.15 8.25 0.85 $10.00 9.65 13.25 10.30 22.15 6.10 2.60 14.15 40.00 9.70 1.05 $13.30 11.90 19.80 12.90 27.75 6.10 3.20 19.15 50.40 10.30 1.05 $17.45 13.85 23.85 16.10 34.65 7.20 3.20 28.00 59.10 11.85 1.15 $19.75 16.20 26.35 20.20 43.35 8.60 3.20 35.05 71.20 12.50 1.50 Sensor Prices Electronic Sensor Type Sourcing Sinking Prewired Part No. 949-000-031 949-000-032 Price $21.20 21.20 Quick Disconnect Part No. 949-000-331 949-000-332 Price $27.85 27.85 Female Cord Set 1 Meter 2 Meters 5 Meters Part No. CFC-1M CFC-2M CFC-5M Price $12.75 14.30 18.05 Sensor Mounting Clamp Kit Number Price SC-1 $4.70 SC-2 $4.70 SC-3 $4.70 and SC-5 $4.70 and SC-7 $4.70 SC-8 $4.70 ccessory Prices Clevis Bracket Trunnion Bracket (Pair) Rod Eye Kit No. 26 CB-3 CB-6 CB-8 Price $14.55 20.60 26.00 Kit No. TB-2 TB-5 TB-7 TB-8 Price $8.10 9.60 11.50 13.50 Specifications subject to change without notice or incurring obligation Kit No. RE-1 RE-2 RE-3 RE-4 RE-6 RE-7 RE-8 Price $10.15 1 1 11.30 11.30 12.65 12.65 8-4-05
Seal Kit Prices Prices effective ugust 15, 2005 Seal Kits Series PSD, PSR, PSX, PWD, PTD Options Standard Viton (V) Low Temperature (Q) Low Friction (L) Low Friction-Viton (L, V) Low Friction-Low Temperature (L, Q) 1/2" PS-1-SK $2.85 PS-1-SKV $5.40 PS-1-SKQ $4.15 PS-1-SKL $3.85 PS-1-SKLV $14.15 PS-1-SKLQ $5.95 3/4" PS-2-SK $4.05 PS-2-SKV $7.00 PS-2-SKQ $4.70 PS-2-SKL $4.35 PS-2-SKLV $13.75 PS-2-SKLQ $6.25 Kit Numbers and Prices by Size 1-1/16" PS-3-SK $3.55 PS-3-SKV $7.30 PS-3-SKQ $4.70 PS-3-SKL $7.50 PS-3-SKLV $22.80 PS-3-SKLQ $7.30 1-1/2" PS-4-SK $3.85 PS-4-SKV $9.45 PS-4-SKQ $5.20 PS-4-SKL $8.10 PS-4-SKLV $24.85 PS-4-SKLQ $7.90 2" PS-5-SK $4.15 PS-5-SKV $13.00 PS-5-SKQ $5.80 PS-5-SKL $8.40 PS-5-SKLV $22.25 PS-5-SKLQ $9.15 2-1/2" PS-6-SK $5.60 PS-6-SKV $20.10 PS-6-SKQ $9.15 PS-6-SKL $10.30 PS-6-SKLV $30.80 PS-6-SKLQ $12.70 3" PS-7-SK $6.15 PS-7-SKV $24.70 PS-7-SKQ $10.80 PS-7-SKL $11.95 PS-7-SKLV $34.10 PS-7-SKLQ $15.60 4" PS-8-SK $5.55 PS-8-SKV $28.35 PS-8-SKQ $9.00 PS-8-SKL $12.60 PS-8-SKLV $37.65 PS-8-SKLQ $14.15 Seal Kits Nonrotating Series PND Options Standard Viton (V) Low Temperature (Q) Kit Numbers and Prices by Size 3/4" PN-2-SK $3.65 PN-2-SKV $6.30 PN-2-SKQ $4.15 1-1/16" PN-3-SK $3.45 PN-3-SKV $6.45 PN-3-SKQ $4.45 1-1/2" PN-4-SK $3.75 PN-4-SKV $8.65 PN-4-SKQ $5.10 2" PN-5-SK $4.05 PN-5-SKV $12.15 PN-5-SKQ $5.60 Seal Kits - Multi-Power Series PM2,, Options Standard Viton (V) Low Temperature (Q) Low Friction (L) Low Friction-Viton (L, V) Low Friction-Low Temperature (L, Q) PM2-2 1 /2" PM2-6-SK $8.85 PM2-6-SKV $28.90 PM2-6-SKQ $14.25 PM2-6-SKL $18.20 PM2-6-SKLV $53.35 PM2-6-SKLQ $21.30 PM2-3" PM2-7-SK $9.50 PM2-7-SKV $34.65 PM2-7-SKQ $16.40 PM2-7-SKL $2 PM2-7-SKLV $57.50 PM2-7-SKLQ $26.25 Kit Numbers and Prices by Stages and Size PM2-4" PM2-8-SK $8.50 PM2-8-SKV $34.95 PM2-8-SKQ $13.50 PM2-8-SKL $22.95 PM2-8-SKLV $65.00 PM2-8-SKLQ $24.45-2 1 /2" -6-SK $12.55-6-SKV $40.40-6-SKQ $22.05-6-SKL $26.55-6-SKLV $77.05-6-SKLQ $30.60-3" -7-SK $13.45-7-SKV $48.55-7-SKQ $22.90-7-SKL $31.10-7-SKLV $82.90-7-SKLQ $37.70-4" -8-SK $12.15-8-SKV $49.60-8-SKQ $19.20-8-SKL $33.85-8-SKLV $94.70-8-SKLQ $35.55-2 1 /2" -6-SK $16.20-6-SKV $51.90-6-SKQ $25.70-6-SKL $34.95-6-SKLV $100.80-6-SKLQ $39.85-3" -7-SK $17.40-7-SKV $62.50-7-SKQ $29.40-7-SKL $40.95-7-SKLV $108.25-7-SKLQ $49.15-4" -8-SK $15.85-8-SKV $64.25-8-SKQ $24.85-8-SKL $44.75-8-SKLV $124.40-8-SKLQ $46.70 Seal Kits - Multi-Position Series P3D 8-4-05 Options Standard Viton (V) Low Temperature (Q) Low Friction (L) Low Friction-Viton (L, V) Low Friction-Low Temperature (L, Q) 1/2" P3-1-SK $3.60 P3-1-SKV $7.35 P3-1-SKQ $5.60 P3-1-SKL $5.55 P3-1-SKLV $24.80 P3-1-SKLQ $9.15 3/4" P3-2-SK $5.20 P3-2-SKV $9.30 P3-2-SKQ $6.10 P3-2-SKL $6.25 P3-2-SKLV $23.70 P3-2-SKLQ $9.70 Kit Numbers and Prices by Size 1-1/16" P3-3-SK $5.65 P3-3-SKV $11.15 P3-3-SKQ $7.40 P3-3-SKL $13.55 P3-3-SKLV $42.10 P3-3-SKLQ $12.60 1-1/2" P3-4-SK $6.20 P3-4-SKV $14.70 P3-4-SKQ $8.25 P3-4-SKL $14.70 P3-4-SKLV $45.50 P3-4-SKLQ $13.70 2" P3-5-SK $6.65 P3-5-SKV $2 P3-5-SKQ $9.20 P3-5-SKL $15.20 P3-5-SKLV $39.50 P3-5-SKLQ $15.85 2-1/2" P3-6-SK $8.85 P3-6-SKV $27.85 P3-6-SKQ $14.25 P3-6-SKL $18.20 P3-6-SKLV $53.35 P3-6-SKLQ $21.30 3" P3-7-SK $9.60 P3-7-SKV $38.70 P3-7-SKQ $16.70 P3-7-SKL $2 P3-7-SKLV $57.50 P3-7-SKLQ $26.25 4" P3-8-SK $8.90 P3-8-SKV $46.40 P3-8-SKQ $14.15 P3-8-SKL $22.95 P3-8-SKLV $65.00 P3-8-SKLQ $24.45 Specifications subject to change without notice or incurring obligation 27