Table of Contents Rotary Cutters RC(M)3615 S/N 945022-27716 330-502P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 07/10/18 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Table of Contents Section 1: Introduction...6 Using This Manual...6 Manual Replacement Information...6 Manual Revisions...6 Touch-up Paint...6 Hardware Legend...7 Replacement Hardware...7 Serial Numbers...7 Part Number Service Coding...7 Section 2: Decks & Hitches...8 Blade Carrier...8 Deck Center Section...10 Deck Wing Section...14 Hitch Ball Coupler...16 Hitch Bar Tite...18 Hitch LP Performance S/N 1000385-...20 Hitch Main Frame...22 Hitch Pintel...24 Hitch Standard Pivoting Clevis...26 Hitch Swivel...28 Leveling Rod & Wing Turnbuckle...30 Section 3: Axles...32 Axle Center S/N 754356-...32 Axle Center S/N 754357+...34 Axle Wing S/N 754356-...36 Axle Wing S/N 754357+...38 Section 4: Guards...40 Guards Chain Double Row Front...40 Guards Chain Double Row Rear...42 Guards Chain Single Row Front...44 Guards Chain Single Row Rear...46 Guards Rubber Front...48 Guards Rubber Rear...50 Section 5: Drivelines (1000 RPM)...52 Driveline Center (826-478C) Comer...52 Driveline Center (826-818C) Comer...54 Driveline Center 1000 RPM (826-184C) Eurocardan...56 Driveline Conv. 1000 RPM (826-247C) Walterscheid...58 Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler...60 Driveline CV 1000 RPM (826-615C) Weasler (S/N 547836+)...62 Driveline CV 1000 RPM (826-644C) Weasler...64 Driveline Slip Clutch (229829X0) Walterscheid...66 Driveline Slip Clutch 1000 RPM (1406016) Eurocardan...68 Driveline Slip Clutch 1000 RPM (1406116) Eurocardan...70 Driveline Slip Clutch 540/1000 RPM (1446016) EC...72 Driveline Wing (826-185C) Eurocardan...74 Driveline Wing (826-185C) Walterscheid...76 Driveline Wing (826-481C) Comer...78 Driveline Wing (826-811C) Comer...80 Driveline Wing (826-812C) Comer...82 Driveline Wing (826-812C) Walterscheid...84 Section 5: Drivelines (540 RPM)...86 Driveline Center (826-478C) Comer...86 Driveline Center (826-818C) Comer...88 Driveline Center 540 RPM (826-183C) Eurocardan...90 Driveline Conv. 540 RPM (826-112C) Walterscheid...92 Driveline CV 540 RPM (826-614C) Weasler...94 Driveline CV 540 RPM (826-643C) Weasler...96 Driveline Slip Clutch (229829X0) Walterscheid...98 Driveline Slip Clutch 540/1000 RPM (1446016) EC...100 Driveline Wing (826-185C) Eurocardan...102 Driveline Wing (826-185C) Walterscheid...104 Driveline Wing (826-481C) Comer...106 Driveline Wing (826-481C) Walterscheid...108 Driveline Wing (826-811C) Comer...110 Driveline Wing (826-812C) Comer...112 Driveline Wing (826-812C) Walterscheid...114 Section 6: Gearboxes (1000 RPM)...116 Gearbox Center Deck (1000 RPM) (826-380C) Comer S/N 397434+...116 Gearbox Divider 1000 RPM (826-281C) Comer...118 Gearbox Divider 1000 RPM (826-281C) OMN...120 Gearbox Divider 1000 RPM (826-281C) SD Engineering.122 Gearbox Left Deck 1000 RPM (826-382C) Comer (S/N 397434+)...124 Gearbox Right Deck 1000 RPM (826-381C) Comer (S/N 397434+)...126 Section 6: Gearboxes (540 RPM)...128 Gearbox Center & Left Deck (540 RPM ) (826-378C) Comer S/N 378036+...128 Gearbox Divider 540 RPM (826-280C) Comer...130 Gearbox Divider 540 RPM (826-280C) SD Engineering..132 Gearbox Right Deck 540 RPM (826-379C) Comer (S/N 378036+)...134 Section 7: Hydraulics...136 Hydraulic Cylinder (810-150C) Cross...136 Hydraulic Cylinder (810-150C) Midway...138 Hydraulic Cylinder (810-150C) Red Lion...140 Hydraulic Cylinder (810-624C) Midway...142 Hydraulic Cylinder (810-624C) Red Lion...144 Hydraulic Lift Components...146 Section 8: Decals...148 Decal Placement...148 Touch-up Paints...150 Section 9: Options & Accessories...152 Hydraulic Independent Wing Control Accessory...152 Copyright 2018. All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Table of Contents (continued) Manual Winch Wing Deck...154 Tire Options...156...158 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 3
Table of Contents Alphabetized Table of Contents A B D G Axle Center S/N 754356-...32 Axle Center S/N 754357+...34 Axle Wing S/N 754356-...36 Axle Wing S/N 754357+...38 Blade Carrier...8 Decal Placement...148 Deck Center Section...10 Deck Wing Section...14 Driveline Center (826-478C) Comer...52 Driveline Center (826-478C) Comer...86 Driveline Center (826-818C) Comer...54 Driveline Center (826-818C) Comer...88 Driveline Center 1000 RPM (826-184C) Eurocardan...56 Driveline Center 540 RPM (826-183C) Eurocardan...90 Driveline Conv. 1000 RPM (826-247C) Walterscheid...58 Driveline Conv. 540 RPM (826-112C) Walterscheid...92 Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler...60 Driveline CV 1000 RPM (826-615C) Weasler (S/N 547836+)...62 Driveline CV 1000 RPM (826-644C) Weasler...64 Driveline CV 540 RPM (826-614C) Weasler...94 Driveline CV 540 RPM (826-643C) Weasler...96 Driveline Slip Clutch (229829X0) Walterscheid...66 Driveline Slip Clutch (229829X0) Walterscheid...98 Driveline Slip Clutch 1000 RPM (1406016) Eurocardan...68 Driveline Slip Clutch 1000 RPM (1406116) Eurocardan...70 Driveline Slip Clutch 540/1000 RPM (1446016) EC...72 Driveline Slip Clutch 540/1000 RPM (1446016) EC...100 Driveline Wing (826-185C) Eurocardan...74 Driveline Wing (826-185C) Eurocardan...102 Driveline Wing (826-185C) Walterscheid...76 Driveline Wing (826-185C) Walterscheid...104 Driveline Wing (826-481C) Comer...78 Driveline Wing (826-481C) Comer...106 Driveline Wing (826-481C) Walterscheid...108 Driveline Wing (826-811C) Comer...80 Driveline Wing (826-811C) Comer...110 Driveline Wing (826-812C) Comer...82 Driveline Wing (826-812C) Comer...112 Driveline Wing (826-812C) Walterscheid...84 Driveline Wing (826-812C) Walterscheid...114 Gearbox Center & Left Deck (540 RPM ) (826-378C) Comer S/N 378036+...128 Gearbox Center Deck (1000 RPM) (826-380C) Comer S/N 397434+...116 Gearbox Divider 1000 RPM (826-281C) Comer...118 Gearbox Divider 1000 RPM (826-281C) OMN...120 Gearbox Divider 1000 RPM (826-281C) SD Engineering.122 Gearbox Divider 540 RPM (826-280C) Comer...130 H L M T Gearbox Divider 540 RPM (826-280C) SD Engineering..132 Gearbox Left Deck 1000 RPM (826-382C) Comer (S/N 397434+)...124 Gearbox Right Deck 1000 RPM (826-381C) Comer (S/N 397434+)...126 Gearbox Right Deck 540 RPM (826-379C) Comer (S/N 378036+)...134 Guards Chain Double Row Front...40 Guards Chain Double Row Rear...42 Guards Chain Single Row Front...44 Guards Chain Single Row Rear...46 Guards Rubber Front...48 Guards Rubber Rear...50 Hitch Ball Coupler...16 Hitch Bar Tite...18 Hitch LP Performance S/N 1000385-...20 Hitch Main Frame...22 Hitch Pintel...24 Hitch Standard Pivoting Clevis...26 Hitch Swivel...28 Hydraulic Cylinder (810-150C) Cross...136 Hydraulic Cylinder (810-150C) Midway...138 Hydraulic Cylinder (810-150C) Red Lion...140 Hydraulic Cylinder (810-624C) Midway...142 Hydraulic Cylinder (810-624C) Red Lion...144 Hydraulic Independent Wing Control Accessory...152 Hydraulic Lift Components...146 Touch-up Paints...150 Leveling Rod & Wing Turnbuckle...30 Manual Winch Wing Deck...154 Tire Options...156 4 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents This Page Intentionally Left Blank 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 5
Table of Contents 6 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 7
Blade Carrier Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-27670 8 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Section 2: Decks & Hitches Blade Carrier Table of Contents Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 7. 7. 8. Dwg 27670 312-075D 312-082D 312-089D 312-808D 312-820H N/A 802-277C 803-170C 804-147C 820-138C 820-137C 820-112C 318-586A Drawing Image Number BLADE SPACER 16 GA..064 Thick BLADE SPACER 18 GA..052 Thick BLADE SPACER 20 GA..04 Thick BLADE SPACER 24GA..03 Thick 15 DISHPAN WLDMT LG.HUB(COMER) ASSY. BLADE CARRIER LH. BLADE BOL 1 1/8-12X3 7/16 W/KY NUT HEX TOP LOCK 1 1/8-12 PLT. WASHER FLAT 1" HARDENED CUTTER BLADE 1/2 X 4 X 31 CCW CUTTER BLADE 1/2 X 4 X 25 CCW CUTTER BLADE 1/2 X 4 X 25 CW BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- Center Deck Right Deck Left Deck 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 9
Table of Contents Deck Center Section Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 2: Decks & Hitches 27688 10 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Deck Center Section Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 5. 5. 5. 5. 5. 5. 5. 6. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. 28. 29. 30. 3 3 3 3 3 3 34. 34. 35. 35. 36. 37. 38. 38. 38. 38. 38. Dwg 27688 318-098H 318-211H 318-212H 318-250D 330-446H 330-446H81 330-446H82 330-446H83 330-740H 330-740H81 330-740H82 330-740H83 330-461H 331-504H 330-462K 802-005C 802-314C 802-055C 802-065C 802-070C 802-214C 802-235C 802-683C 802-684C 803-026C 803-168C 803-169C 803-255C 803-263C 803-299C 804-007C 804-009C 804-010C 804-012C 804-013C 804-025C 807-023C 807-143C 816-481C 817-259C 826-183C 826-184C 826-818C 826-478C 826-280C 826-281C 826-378C 826-380C 826-490C 826-497C 826-643C 826-614C 826-112C 826-247C 826-644C Drawing Image Number WLDMT. SHIELD BRACKET WLDMT. SKID SHOE RH. WLDMT. SKID SHOE LH. SHIELD DIVIDER BOX DECK CENTER DECK CENTER GREEN DECK CENTER ORANGE DECK CENTER RED DECK CENTER W/DR DECK CENTER W/DR GREEN DECK CENTER W/DR ORANGE DECK CENTER W/DR RED CYLINDER SPRING BASE CYLINDER SPRING BASE 29" TIRES GEARBOX SHIELD ASSY HHCS 1/4-20X1 GR5 HHCS M8X25X20 GR8.8 HHCS 5/8-11X2 GR5 HHCS 3/4-10X2 1/4 GR5 HHCS 3/4-10X6 GR5 RHSNB 1/2-13X1 1/4 GR5 HHCS 1-8X5 GR5 HHCS M8X25X45 GR8.8 HHCS M8X25X55 GR8.8 NUT LOCK 3/4-10 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLG. LOCK 1/2-13 PLT. NUT HEX NYLOCK 1/4-20 NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER FLAT 1/4 SAE PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 3/4 SAE PLT SPRING HOSE LOOP SPRING COMP 88OD x.362w MANUAL STORAGE CONTAINER KNOB 3/8-16 FEMALE THD 2 3/8OD PTO INT. CAT.4 540W/CLUTCH PTO INT. CAT.4 1000W/CLUTCH PTO E60 X 27 1280NM CLUTCH PTO E60 X 27 1280NM CLUTCH DIV. OMNI/CO 540RPM SU DIVIDER OMNI/CO 1000RPM RD GBOX RC35 75-20 1:47 STD. GBOX RC35 75-20 21:1 STD. COMER U0.210.7100.00 DIPSTICK COMER VENT #8.6.7.00269 DRVLN C6 42 38-6 CV RPBY 826-643C PTO 2500 X 39.76 NO CLUTCH PTO 2500 CAT.5 1000 1 3/8-21 DRVLN C6 42 38-21 CV Without Deck Rings With Deck Rings Use With 29" Tires Started Using S/N 861324 RC3615 RCM3615 S/N 928454+ S/N 928453- RC(M)3615 RC3615 RCM3615 RC3615 RCM3615 RC3615 S/N 639775+ RC3615 S/N 639774- (Obsolete) RC3615 RCM3615 RCM3615 S/N 645002+ 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 11
Table of Contents Deck Center Section (continued) Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 2: Decks & Hitches Ref. 38. 38. 39. Part No. 826-615C 826-793C 840-273C Part Description RPBY 826-644C DRVLN C6 39 38-21 CV ORCLTCH PLUG LP 3" ID RUBBER Comments RCM3615 S/N 645001- ---- (Obsolete) RCM3615 Revision 12 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Deck Center Section (continued) Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- This Page Intentionally Left Blank 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 13
Table of Contents Deck Wing Section Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 2: Decks & Hitches 27687 14 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Deck Wing Section Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 16. 16. 16. 17. 18. 18. 19. 19. 20. 2 dwg27687 318-247D 330-068D 330-101D 330-456H 330-456H81 330-456H82 330-456H83 330-741H 330-741H81 330-741H82 330-741H83 330-457H 330-457H81 330-457H82 330-457H83 330-742H 330-742H81 330-742H82 330-742H83 330-504H 802-314C 802-022C 802-065C 802-155C 802-466C 803-014C 803-198C 803-299C 804-009C 804-010C 804-013C 826-811C 826-185C 826-812C 826-481C 826-648C 826-378C 826-382C 826-379C 826-381C 826-490C 840-273C Drawing Image Number SKID SHOE DEFLECTOR RH DEFLECTOR LH DECK RH WING DECK RH WING GREEN DECK RH WING ORANGE DECK RH WING RED DECK RH WING W/DR DECK RH WING W/DR GREEN DECK RH WING W/DR ORANGE DECK RH WING W/DR RED DECK LH WING DECK LH WING GREEN DECK LH WING ORANGE DECK LH WING RED DECK LH WING W/DR DECK LH WING W/DR GREEN DECK LH WING W/DR ORANGE DECK LH WING W/DR RED HINGE ROD HHCS M8X25X20 GR8.8 HHCS 3/8-16X1 1/2 GR5 HHCS 3/4-10X2 1/4 GR5 RHSNB 3/8-16X1 1/4 GR5 PLOW 3/8-16X1 1/4 GR5 NUT HEX 3/8-16 PLT NUT HEX WHIZ 3/8-16 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER LOCK SPRING 3/8 PLT DRVLN C4 50 75-20 FX CLTCH PTO CAT.4 W/CLUTCH 1 3/4-20 PTO CAT.5 W/CLUTCH 1 3/4-20 RPBY 826-812C LARGE SHAFT CONE W ACCESS DOOR GBOX RC35 75-20 1:47 STD. GBOX RC35 75-20 1:21 STD. GBOX RC35 75-20 1:47 REV. GBOX RC35 75-20 1:21 REV. COMER U0.210.7100.00 DIPSTICK PLUG LP 3" ID RUBBER Without Deck Rings With Deck Rings Without Deck Rings With Deck Rings S/N 929017+ S/N 929016- RC3615 & RCM3615 S/N 914796+ RC3615 & RCM3615 S/N 914795- RC3615 & RCM3615 LH Deck RC3615 LH Deck RCM3615 RH Deck RC3615 RH Deck RCM3615 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 15
Hitch Ball Coupler Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-26568 16 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hitch Ball Coupler Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision Dwg 26568 330-335A 330-348H 802-053C 802-082C 803-304C 803-037C Drawing Image Number 2 5/16" BALL HITCH ASSEMBLY * 2 5/16" BALL HITCH WELDMENT HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT S/N 615584+ S/N 615583- S/N 615584+ S/N 615583-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 17
Hitch Bar Tite Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-26569 18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Section 2: Decks & Hitches Hitch Bar Tite Table of Contents Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 8. 9. 9. 10. 1 1 1 1 14. 15. 16. 16. 17. 18. 19. 20. 2 2 Dwg 26569 330-333A 318-358H 318-834H 330-271H 330-563D 330-564D 330-975H 800-001C 802-053C 802-082C 802-070C 802-594C 802-074C 802-205C 802-235C 803-168C 803-181C 803-258C 803-301C 803-304C 803-037C 804-025C 804-028C 804-171C 805-105C 890-862C 330-974K Drawing Image Number BAR TITE HITCH * SHAFT WELDMENT WELDMENT HITCH CLEVIS SWIVEL RECEIVER HITCH WEAR PLATE WIDE FORMED HITCH SUPPORT WIDE BAR TITE WIDE TOP GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 3/4-10X6 GR5 HHCS 3/4-10X5 1/2 GR5 HHCS 1-8X6 1/2 GR5 HHCS 1-8X5 1/2 GR5 HHCS 1-8X5 GR5 NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 3/4-10 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER FLAT 50 HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING 50ODX00IDX25 BAR TITE HITCH WIDE S/N 615584+ S/N 615583- S/N + S/N - S/N + S/N - S/N 615584+ S/N 615583-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 19
Table of Contents Hitch LP Performance S/N 1000385- Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 2: Decks & Hitches 37646 20 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hitch LP Performance S/N 1000385- Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. Dwg 37646 334-045A 330-271H 334-046H 334-048H 800-001C 802-053C 802-075C 802-079C 803-201C 803-258C 803-301C 803-304C 804-013C 805-105C 890-836C 890-850C 331-543D Image No. LP PERFORMANCE HITCH SWIVEL RECEIVER HITCH CLEVIS HITCH YOKE GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X7 GR5 HHCS 3/8-16X1 1/4 GR5 NUT HEX COUPLER 3/8-16X1 3/4 NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT WASHER LOCK SPRING 3/8 PLT PIN COTTER 1/4 X 2 1/2 PLT BUSHING 1 1/4X1X1/2 HRD BUSHING 1 1/4X1X5/8 HITCH HOLDER If you order this part you will receive the updated version. You will also need to order item 16 to go with the updated item 2 If you order this part you will receive the updated version 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 21
Hitch Main Frame Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-27671 22 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hitch Main Frame Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. dwg27671 330-460H 800-080C 802-096C 802-235C 803-168C 804-028C 890-182C 890-226C Drawing Image Number HITCH GREASE ZERK 1/4-28 THD FORMING HHCS 1-8X2 1/2 GR5 HHCS 1-8X5 GR5 NUT HEX TOP LOCK 1-8 PLT WASHER FLAT 1 USS PLT SAFETY CHAIN 10000 LB SIDEWIND JACK 5000 LB 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 23
Hitch Pintel Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-27673 24 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Section 2: Decks & Hitches Hitch Pintel Table of Contents Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 4. 5. 6. dwg27673 330-501A 330-499H 802-053C 802-082C 802-729C 803-304C 803-037C 803-304C 890-806C Drawing Image Number PINTLE HITCH * PINTLE RECEIVER HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HFS 5/8-11X2 1/2 GR8 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX WHIZ 5/8-11 PLT PINTLE HOOK SQ.BASE BDB1250-15 S/N 615584+ S/N 615583- S/N 615584+ S/N 615583-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 25
Table of Contents Hitch Standard Pivoting Clevis Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 2: Decks & Hitches 27672 26 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hitch Standard Pivoting Clevis Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. Dwg 27672 330-498A 330-163D 330-497H 330-500H 802-053C 802-110C 802-356C 803-024C 803-258C 803-304C Drawing Image Number STANDARD HITCH * SPACER HITCH CLEVIS WELDMENT YOKE HITCH 3615 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X9 GR5 HHCS 5/8-11X8 1/2 GR5 NUT LOCK 5/8-11 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 27
Hitch Swivel Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-26571 28 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Section 2: Decks & Hitches Hitch Swivel Table of Contents Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 6. 7. 8. 9. 10. 1 1 1 1 14. 15. 16. 17. 18. 19. Dwg 26571 330-332A 318-357H 331-211H 330-271H 330-321H 800-080C 802-053C 802-082C 802-074C 802-205C 803-030C 803-258C 803-301C 803-304C 803-037C 803-031C 804-028C 804-171C 805-105C 890-005C 890-850C 330-648S Drawing Image Number SWIVEL HITCH * CLEVIS WELDMENT SHAFT WELDMENT SWIVEL RECEIVER CLEVIS SWIVEL GREASE ZERK 1/4-28 THD FORMING HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 1-8X6 1/2 GR5 HHCS 1-8X5 1/2 GR5 NUT HEX JAM 1-8 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX 1-8 PLT WASHER FLAT 1 USS PLT WASHER FLAT 1 3/8HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING CYL 1 1/4 X 1 X 1 BUSHING 1 1/4X1X5/8 ASSY SWIVEL CLEVIS Replaced By 330-648S S/N 615584+ S/N 615583- S/N 615584+ S/N 615583-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 29
Table of Contents Leveling Rod & Wing Turnbuckle Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 2: Decks & Hitches 27674 30 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Leveling Rod & Wing Turnbuckle Section 2: Decks & Hitches Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. Dwg 27674 318-008H 330-470H 330-471K 800-001C 802-098C 802-205C 802-538C 803-032C 803-075C 803-084C 803-168C 803-265C 804-025C 804-030C 805-083C 805-109C 890-974C Drawing Image Number WLDMT. LEVEL ROD SHORT LEVEL ROD LONG LEVEL ROD GREASE ZERK STRAIGHT 1/4-28 HHCS 1-8X4 1/2 GR5 HHCS 1-8X5 1/2 GR5 HSHCS 5/16-18X1 3/4 NUT HEX JAM 1 1/4-7 PLT NUT HEX JAM 7/8-9 NUT HEX NYLOCK 5/16-18 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX COUPLER 7/8-9 x 5 WASHER FLAT 3/4 SAE PLT WASHER LOCK 1 1/4 SPRING PLT PIN CLEVIS 3/4 X 1 1/2 PIN COTTER 1/8 X 1 1/4 PLT TRNBCKL, 1BORE W/SWIVEL 9.5 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 31
Table of Contents Axle Center S/N 754356- Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 3: Axles 27668 32 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Axle Center S/N 754356- Section 3: Axles Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 dwg27668 200-001D 330-980A 330-478H 800-080C 802-099C 802-110C 802-205C 802-779C 803-019C 803-053C 803-168C 803-310C 804-216C 805-246C 815-237C 815-238C 815-243C 815-244C 816-497C 822-020C 822-021C 822-033C 822-034C Drawing Image Number HUB GREASE CAP CENTER AXLE W/DUAL SPINDLES RPBY 330-980A GREASE ZERK 1/4-28 THD FORMING HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X9 GR5 HHCS 1-8X5 1/2 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 3/4-16 NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER HARDENED 3/4 PIN COTTER 5/32 X 1 3/4 LG SPINDLE-SINGLE BOLT-ON SPINDLE-DUAL BOLT-ON HUB 5-BOLT W/CUPS/STUDS HUB 5-BOLT COMPLETE SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 33
Table of Contents Axle Center S/N 754357+ Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 3: Axles 35069 34 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Axle Center S/N 754357+ Section 3: Axles Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. dwg35069 200-001D 330-938K 330-978H 800-080C 802-099C 802-110C 802-205C 802-779C 803-019C 803-029C 803-168C 803-310C 804-055C 805-246C 815-242C 815-243C 815-403C 815-404C 815-435C 816-497C 822-020C 822-021C 822-033C 822-034C Drawing Image Number HUB GREASE CAP HUB 5 BOLT COMPLETE AXLE CENTER GREASE ZERK 1/4-28 THD FORMING HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X9 GR5 HHCS 1-8X5 1/2 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT CASTING HUB 5-BOLT W/CUPS/STUDS SPINDLE OFFSET, DUAL BOLT-ON SPINDLE, SINGLE BOLT ON 15 SPINDLE, SINGLE-BOLT ON 7/8-14 SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 Short Side Out W/29" Tire All Tires Except 29" AC 29" AC Tire Only 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 35
Table of Contents Axle Wing S/N 754356- Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 3: Axles 27669 36 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Axle Wing S/N 754356- Section 3: Axles Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 dwg27669 200-001D 330-479H 330-480H 800-080C 802-098C 802-099C 802-357C 802-779C 803-019C 803-053C 803-168C 803-310C 804-216C 805-246C 815-237C 815-238C 815-243C 815-244C 816-497C 822-020C 822-021C 822-033C 822-034C Drawing Image Number HUB GREASE CAP AXLE WING RH AXLE WING LH GREASE ZERK 1/4-28 THD FORMING HHCS 1-8X4 1/2 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X6 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 3/4-16 NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER HARDENED 3/4 PIN COTTER 5/32 X 1 3/4 LG SPINDLE-SINGLE BOLT-ON SPINDLE-DUAL BOLT-ON HUB 5-BOLT W/CUPS/STUDS HUB 5-BOLT COMPLETE SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 Shown 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 37
Table of Contents Axle Wing S/N 754357+ Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 3: Axles 35070 38 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Axle Wing S/N 754357+ Section 3: Axles Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 dwg35070 200-001D 330-479H 330-480H 330-938K 800-080C 802-098C 802-099C 802-357C 802-779C 803-019C 803-029C 803-168C 803-310C 804-055C 805-246C 815-242C 815-243C 815-401C 815-402C 816-497C 822-020C 822-021C 822-033C 822-034C Drawing Image Number HUB GREASE CAP AXLE WING RH AXLE WING LH HUB 5 BOLT COMPLETE GREASE ZERK 1/4-28 THD FORMING HHCS 1-8X4 1/2 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X6 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT CASTING HUB 5-BOLT W/CUPS/STUDS SPINDLE, SINGLE BOLT-ON 7/8-14 SPINDLE, DUAL BOLT-ON 7/8-14 SEAL 75ID CR17617 BRG CUP LM-67010 BRG CONE 25ID LM-67048 BRG CUP LM-48510 BRG CONE LM-48548 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 39
Table of Contents Guards Chain Double Row Front Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 4: Guards 27679 40 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Guards Chain Double Row Front Section 4: Guards Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. Dwg 27679 330-483A 318-108D 318-336D 318-337D 318-431D 318-519D 318-876K 318-879K 330-105D 330-106D 330-474K 330-475K 802-015C 803-198C 890-175C 890-341C Drawing Image Number CHNGRD FRONT DOUBLE * ROUND ROD 1/4 X 36 ROUND ROD 1/4 X 73 ROUND ROD 1/4 X 25 CHAINGUARD DBL FRONT CTR CHAINGUARD DBL FRONT WING ASSY. DUAL CHAINGUARD FRT.CTR ASSY.DUAL CHAINGUARD FRT.WING CHNGRD DBL FRT RH CHNGRD DBL FRT LH CHNGRD DBL FRT RH CHNGRD DBL FRT LH RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 5 LINK 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 41
Table of Contents Guards Chain Double Row Rear Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 4: Guards 27682 42 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Guards Chain Double Row Rear Section 4: Guards Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. Dwg 27682 330-495A 318-107D 318-641D 318-895D 330-119D 330-214K 330-477K 802-015C 803-198C 890-175C 890-393C Drawing Image Number CHNGRD REAR DOUBLE * ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 9 CHNGRD REAR CNTR INNER DBL CHNGRD DBL REAR OUT CHNGRD CNTR REAR INNER DBL CHNGRD DBL REAR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 7-LINK 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 43
Table of Contents Guards Chain Single Row Front Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 4: Guards 27675 44 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Guards Chain Single Row Front Section 4: Guards Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. Dwg 27675 330-481A 318-223K 318-226K 318-265D 318-108D 318-268D 318-336D 318-337D 330-103D 330-104D 330-472K 330-473K 802-015C 803-198C 890-175C 890-341C Drawing Image Number CHNGRD FRONT SINGLE * ASSY. CHAINGUARD FRT. CTR. ASSY. CHAINGUARD FRT. WING CHAINGUARD BRKT. FRT. CTR. ROUND ROD 1/4 X 36 CHAINGUARD BRKT. FRT. WING ROUND ROD 1/4 X 73 ROUND ROD 1/4 X 25 CHNGRD SGL FRT RH CHNGRD SGL FRT LH CHNGRD SGL FRT RH CHNGRD SGL FRT LH RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 5 LINK 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 45
Table of Contents Guards Chain Single Row Rear Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 4: Guards 27676 46 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Guards Chain Single Row Rear Section 4: Guards Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. Dwg 27676 330-493A 318-107D 318-641D 318-876D 330-107D 330-208K 330-476K 802-015C 803-198C 890-175C 890-393C Drawing Image Number CHNGRD REAR SINGLE * ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 9 BRACKET CHNGRD CNTR INNER CHNGRD SGL REAR OUT CHNGRD CNTR REAR INNER CHNGRD SGL REAR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 7-LINK 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 47
Table of Contents Guards Rubber Front Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 4: Guards 27683 48 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Guards Rubber Front Section 4: Guards Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. Dwg 27683 330-482A 318-210D 318-234D 318-235D 318-237D 318-240D 318-242K 318-245K 330-118D 330-484K 802-015C 803-198C 816-325C 816-326C 816-327C Drawing Image Number RUBBERGUARD FRONT * DEFLECTOR BRKT. FRT. CTR. DEFLECTOR BRKT. FRT. WING DEFLECTOR STRAP DEFLECTOR STRAP DEFLECTOR STRAP ASSY. FRONT RUBBER CTR. ASSY. FRONT RUBBER WING RUBBERGUARD CNTR FRT RUBBERGUARD CTR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT RUBBER DEFLECTOR FRT. CTR. RUBBER DEF. FRT. CTR. OUT. RUBBER DEFLECTOR FRT. WING 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 49
Table of Contents Guards Rubber Rear Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 4: Guards 27684 50 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Guards Rubber Rear Section 4: Guards Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. Dwg 27684 330-494A 318-129D 318-934D 330-120D 330-121D 330-241K 330-496K 802-015C 803-198C 816-244C 816-641C Drawing Image Number RUBBER GUARD REAR * RUBBER GUARD FLAT BRKT. 28 1/2 BKT REAR CTR INNER RUBBER GRD BKT RBBRGRD CNTR OUT FLAT SUPPORT BAND ASY CTR REAR INNER RUBBER GRD RUBBERGUARD REAR CNTR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT RUBBER GUARD REAR CENTER RUBBER DEF REAR CNT OUT 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 51
Table of Contents Driveline Center (826-478C) Comer Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 23952 52 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Center (826-478C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. dwg23952 826-478C 14026.357.1 180.016.130 170.016.630.1 155.150.724 190.000.016 15016.031 146.264.024.1 165.000.589 Drawing Image Number PTO E60 X 27 1280NM CLUTCH * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE COMER INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 Cat. 5 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 53
Table of Contents Driveline Center (826-818C) Comer Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 37510 54 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Center (826-818C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. Dwg 37510 826-818C 14026.357.1 180.016.780 190.000.032 190.000.047 170.016.630.1 155.150.724 190.000.016 15016.896.1 146.264.024.1 165.000.589 180.014.022 15016.037.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 Image No. PTO E60 X 27 1280NM CLUTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE CO INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 55
Table of Contents Driveline Center 1000 RPM (826-184C) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-19030 56 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Center 1000 RPM (826-184C) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 6. 7. 8. 9. 10. 1 dwg19030 826-184C 1106525 1006020 1706027 6331080 1528316D 1406116 1406016 6141280 6412112 6410112 6761280 6560508 Drawing Image Number PTO INT. CAT.4 1000W/CLUTCH EC YOKE ASSEMBLY (TRACT. END) EC CROSS ASSEMBLY EC OUTER TUBE YOKE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE EC CLUTCH FD2/6 1 3/4" Z20 RPBY 1406116 EC.BOLT EC SPRING WASHER EC NUT EC BOLT ASSY KIT EC GREASE ZERK 8X1 45 DEG. Includes item 10 Includes items 7, 8 & 9 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 57
Table of Contents Driveline Conv. 1000 RPM (826-247C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-18549 58 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Conv. 1000 RPM (826-247C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 Dwg 18549 826-247C 325027 362430 312209 097140 304046 333645 387768 097133 818-540C 365305 087276 044321 391409 818-552C 391410 364915 377437 380371 355155 702352 304011 826-603C 359474 Drawing Image Number PTO 2500 CAT.5 1000 1 3/8-21 * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS YOKE 1 3/8-21 SPL. AS WS CROSS & BEARING KIT 2500 WS INBOARD YOKE 2500 WS SPRING PIN 10 X 90 WS INNER PROFILE S4 WS PROFILE & SLEEVE W.A. WS INBOARD YOKE 2400 DECAL DANGER GUARD MISS PTO WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS OUTER SHIELD TUBE OVAL DECAL DANGER PTO DRIVELINE WS INNER SHIELD TUBE RND. WS ASSY COLLAR KIT WS SHIELD CONE 7 RIB WS ZERK WS SUPPORT BEARING WS HEX BOLT M16 X 90 GR 8.8 WS LOCK NUT M16 SHIELD KIT, 826-247C WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 59
Table of Contents Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 35997 60 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline CV 38 1000 RPM W/ Overrunning Clutch (826-793C) Weasler Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 Dwg 35997 826-793C 26-15120 68810-1003 03-15570 26-16033 99-24406 97-26654 19-15135 13-10021 13-10022 96-26654 98-26654 03-15316 39-10039 Drawing Image Number DRVLN C6 39 38-21 CV ORCLTCH * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE OUTER GUARD WE GUARD REPAIR KIT WE SAFETY SIGN WE SAFETY SIGN WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE OVERRUNNING THRST CLTCH ASM 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 61
Table of Contents Driveline CV 1000 RPM (826-615C) Weasler (S/N 547836+) Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-25737 62 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline CV 1000 RPM (826-615C) Weasler (S/N 547836+) Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. Dwg 25737 826-615C 26-15120 35221-2401 03-10016 26-15142 99-23923 19-15129 97-23923 96-23923 19-15121 98-23923 03-10089 44051-1107 11-14988 11-15180 93-23924 92-23923 Drawing Image Number RPBY 826-644C * WE SSL/AUTO-LOK REPAIR KIT WE AUTO-LOK YOKE ASY WE CAT 5 80 CROSS & BRG KIT WE CNTR HOUSING WE YOKE & SFT (69-20 SPL) WE GRD REPAIR KIT WE OUTER GRD WE INNER GRD WE GRD REPAIR KIT WE YOKE, TB & SLIP SLEEVE WE 44R CROSS & BRG KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT & SFT HALF ASY W/GRD WE JOINT & TB HALF ASY W/GRD 1 3/8-21 Spline ---- (Obsolete) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 63
Table of Contents Driveline CV 1000 RPM (826-644C) Weasler Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-30187 64 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline CV 1000 RPM (826-644C) Weasler Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. Dwg 30187 826-644C 26-15120 68810-1003 03-15570 26-16033 99-24406 19-15135 19-15121 97-25023 96-24406 98-24406 03-15316 55051-1817 11-14988 11-15180 93-25023 92-24406 91-25023 11-80005 Drawing Image Number DRVLN C6 42 38-21 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE GRD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET WE CHAIN S/N 712190+ S/N 712189- S/N 928934-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 65
Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-25962 66 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. dwg25962 229829X0 396298 168556 391567 391350 391351 020452 803-280C 30005 020467 Drawing Image Number WS FRICTION CLUTCH * WS FLANGE YOKE WS FRICTION DISK WS HUB 1 3/4-20 I.C. WS THRUST PLATE WS BELLEVILLE SPRING WS HEX BOLT M10X50 NUT HEX NYLOCK M10X5 PLT COSMO WING NUT M8 WS HEX BOLT M12X65 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 67
Table of Contents Driveline Slip Clutch 1000 RPM (1406016) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-15523 68 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Slip Clutch 1000 RPM (1406016) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 6. 7. 8. 9. 10. dwg15523 1406016 1215012 1706033 1705009 1808010 1708017 1236039 6821484 1138008 1138007 6691080 330-297A Drawing Image Number EC CLUTCH FD2/6 1 3/4 20 SPL RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC HUB WITH FLANGE EC 7 DEGREE CONICAL DOG CONICAL DOG KIT EC INNER DISK EC PRESSURE DISK EC COMPLETE BOLT SV KIT, EC SLIP CLUTCH SPRING Contains 8 Springs Rev. 2 not compat. w/rev. Rev. 1 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 69
Table of Contents Driveline Slip Clutch 1000 RPM (1406116) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-33826 70 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Slip Clutch 1000 RPM (1406116) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 Dwg 33826 1406116 1707033 1708017 803-279C 6001085 1215010 1138007 1138008 1808010 6821484 1236039 6410614 6412014 1705009 Drawing Image Number EC CLUTCH FD2/6 1 3/4" Z20 * EC FD2-4/6 FLANGE WITH YOKE EC HUB WITH FLANGE NUT HEX M10X5 PLT EC BOLT (M10X85) EC SPRING EC PRESSURE DISK EC INNER DISK EC CLUTCH LINING RING CONICAL DOG KIT RPBY 6821484 EC SELF LOCK SCREW NUT (M14) EC WASHER (D14) EC CLUTCH BUSHING 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 71
Table of Contents Driveline Slip Clutch 540/1000 RPM (1446016) EC Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-15521 72 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Slip Clutch 540/1000 RPM (1446016) EC Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 dwg15521 1446016 1215012 1706033 1705009 1808010 1708034 1138008 1708016 6821484 1138007 6691010 330-297A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL * RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC PRESSURE DISK EC BOLT & SCREW NUT KIT REPL. SV KIT, EC SLIP CLUTCH SPRING Includes nut and washer Contains 8 Springs 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 73
Table of Contents Driveline Wing (826-185C) Eurocardan Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 16366 74 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-185C) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. 28. 29. dwg16366 826-185C 1786711 1215733 1885702 1215735 1885709 1877111 1876901 1885703 1786710 1446016 1006020 1706029 1526121 6331070 1528901 6331080 1706027 1016025 818-540C 818-552C 044321 6560508 1006220 6560006 1106025 6761480 6410114 6412114 826-581C Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD 1110MM EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD4/6 1 3/4 20 SPL EC CROSS ASSEMBLY EC INNER TUBE YOKE EC 1210MM INNER TUBE EC 10X70 ROLL PIN EC OUTER TUBE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSY 1 3/4-20(TRAC.END DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT(TRACT END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE EC BOLT EC SCREW NUT (M14) EC WASHER (d14) SHIELD KIT, 826-185C (S/N 928934-) Includes 27,28 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 75
Table of Contents Driveline Wing (826-185C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-25920 76 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-185C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. dwg25920 826-185C 229845X0 HM.243 020617 28133000 315892 384202 28133100 229829X0 105083 398294 398297 087276 044321 365305 355155 020466 30005 359471 Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20SPL I.C. WS CROSS & BRG KIT WS SPRING PIN 10 X 20 WS INBOARD YOKE 1B WS INNER PROFILE 1B 2400 WS PROFILE & SLEEVE W.A.1B/2AL WS INBOARD YOKE 2A WS FRICTION CLUTCH WS SHIELD CONE WS GUARD TUBE OUTER WS GUARD TUBE INNER WS BRG RING - SC25 DRIVELINE SHIELD SAFETY CHAIN WS SCREW WS SUPPORT BRG WS BOLT M12 X 60-8.8 COSMO WING NUT M8 WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 77
Table of Contents Driveline Wing (826-481C) Comer Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 23953 78 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-481C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. dwg23953 826-481C 14028.195.1 180.018.004 15018.241 190.000.243 180.018.437 1522805450710 146.284.020.1 180.018.251 180.014.240 180.018.252 180.016.025 165.000.589 12580.021 12580.511 1422831949821 1422871029821 180.018.393 Drawing Image Number RPBY 826-812C * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE OUTER COMER OUTER TUBE ROLL PIN COMER WIPER COMER TUBE OUTER COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER COMER SAFTEY CHAINS COMER TAPERED PIN SET 1 3/4 COMER TUBE W/YOKE/LUBE/FEMALE COMER TUBE W/YOKE/LUBE/MALE COMER HALF FEMALE GRD W/LABEL COMER HALF MALE GUARDING COMER CAP OUTER TUBE, PLASTIC (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 79
Table of Contents Driveline Wing (826-811C) Comer Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 37509 80 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-811C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 Dwg 37509 826-811C 14026.357.1 180.016.780 146.264.024.1 8180.016.237 8180.014.240 8180.016.238 180.016.790 14260.5197621 165.000.589 180.014.022 15016.037.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 812360.504.11 812460.105611 190.000.098 190.000.099 190.000.903 Image No. DRVLN C4 50 75-20 FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET COMER CLUTCH, COMPLETE ASSY CO RETAINING COLLAR OUTER TUBE RPBY 180.014.240 CO RETAINING COLLAR INNER TUBE CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARD COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER CO LABEL W/CUSTOMER CODE (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 81
Table of Contents Driveline Wing (826-812C) Comer Applies to RCM3615 S/N 945022- Section 5: Drivelines (1000 RPM) 37553 82 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-812C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. 28. 29. 30. 3 3 3 34. 35. 36. 37. Dwg 37553 826-812C 14028.195.1 180.018.581 190.000.035 190.000.047 15018.241 190.000.243 150.285197810 159.280.168 190.000.271 15018.241 146.284.020.1 180.018.251 180.014.240 180.018.252 180.016.790 14286.2519821 165.000.589 180.014.022 15018.016.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 12028.10301 12028.1025.01 14282509821 14287.2199821 12386.190.01 12486.3401 190.000.098 190.000.099 180.018.393 180.018.435 190.000.932 Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE OUTER COMER OUTER TUBE ROLL PIN CO COMPLETE OUTER TUBE W/LABEL COMER INNER TUBE COMER ROLL PIN FOR INNER TUBE COMER INNER YOKE COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO U-JOINT FOR OUTER TUBE CO U-JOINT FOR INNER TUBE CO HALF FEMALE GUARD CO HALF MALE GUARD CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER COMER CAP OUTER TUBE, PLASTIC COMER INNER CAP CO LABEL W/CUSTOMER CODE (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 83
Table of Contents Driveline Wing (826-812C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022-37502 84 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-812C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 Dwg 37502 826-812C 325027 190224 097133 304046 323524 397493 097140 395980 125142 087276 371708 371709 399469 365305 383333 383334 044321 396295 380371 359474 125140 107542 Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS CROSS & BEARING KIT WS INBOARD YOKE S4 WS SPRING PIN 10 X 90 WS INNER PROFILE S4L WS OUTER PROFILE S5L WS INBOARD YOKE S5 WS FRICTION CLUTCH WS GUARD CONE 7 RIB WS BRG RING - SC25 WS GUARD TUBE OUTER RPBY 371708 WS GUARD TUBE INNER WS SCREW RPBY 818-552C RPBY 818-540C DRIVELINE SHIELD SAFETY CHAIN WS SUPPORT BEARING WS ZERK WS REINFORCING COLLAR WS GUARD CONE 6 RIB CC LOCK ASSY (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 85
Table of Contents Driveline Center (826-478C) Comer Applies to RC3615 S/N 945022- Section 5: Drivelines (540 RPM) 23952 86 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Center (826-478C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. dwg23952 826-478C 14026.357.1 180.016.130 170.016.630.1 155.150.724 190.000.016 15016.031 146.264.024.1 165.000.589 Drawing Image Number PTO E60 X 27 1280NM CLUTCH * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE COMER INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 Cat. 5 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 87
Table of Contents Driveline Center (826-818C) Comer Applies to RC3615 S/N 945022- Section 5: Drivelines (540 RPM) 37510 88 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Center (826-818C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. Dwg 37510 826-818C 14026.357.1 180.016.780 190.000.032 190.000.047 170.016.630.1 155.150.724 190.000.016 15016.896.1 146.264.024.1 165.000.589 180.014.022 15016.037.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 Image No. PTO E60 X 27 1280NM CLUTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE CO INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 89
Table of Contents Driveline Center 540 RPM (826-183C) Eurocardan Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-15570 90 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Center 540 RPM (826-183C) Eurocardan Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 5. 6. 7. 8. 9. 10. dwg15570 826-183C 6761280 1106525 1006020 1706027 6331080 1528014D 1528304 1446016 6141280 6412112 6410112 084099 Drawing Image Number PTO INT. CAT.4 540W/CLUTCH * EC BOLT ASSY KIT YOKE ASSEMBLY (TRACTOR END) CROSS ASSEMBLY OUTER TUBE YOKE 10 X 80-DIN-148 ROLL PIN EC TUBE JACK SHAFT RPBY 1528014D TORQUE LIMITER 4 FRICTION DISC EC.BOLT EC SPRING WASHER EC NUT WS ZERK M8 X 1 Includes items 7, 8 & 9 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 91
Table of Contents Driveline Conv. 540 RPM (826-112C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-18548 92 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Conv. 540 RPM (826-112C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. Dwg 18548 826-112C 325027 362428 312209 097140 304046 321256 390257 097133 818-540C 365305 087276 044321 389850 818-552C 388957 339107 377437 380371 355155 702352 304011 377442 826-587C 359474 Drawing Image Number PTO 2500 X 39.76 NO CLUTCH * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS YOKE 1 3/8"-6 SPL. ASG WS CROSS & BEARING KIT 2500 WS INBOARD YOKE 2500 WS SPRING PIN 10 X 90 WS INNER PROFILE 2400 WS PROFILE & SLEEVE W.A. WS INBOARD YOKE 2400 DECAL DANGER GUARD MISS PTO WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS OUTER SHIELD TUBE RND. DECAL DANGER PTO DRIVELINE WS INNER SHIELD TUBE ROUND WS Q.D. PIN KIT WS SHIELD CONE 7 RIB WS ZERK WS SUPPORT BEARING WS HEX BOLT M16 X 90 GR 8.8 WS LOCK NUT M16 WS SHIELD CONE - 12 RIB SHIELD KIT, 826-112C WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 93
Table of Contents Driveline CV 540 RPM (826-614C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-25736 94 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline CV 540 RPM (826-614C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. Dwg 25736 826-614C 26-15120 35221-2404 03-10016 26-15142 99-23923 19-15129 97-23923 96-23923 19-15121 98-23923 03-10089 44051-1107 11-14988 11-15180 93-23923 92-23923 Drawing Image Number RPBY 826-643C * WE SSL/AUTO-LOK REPAIR KIT WE AUTO-LOK YOKE ASY WE CAT 5 80 CROSS & BRG KIT WE CNTR HOUSING WE YOKE & SFT (69-20 SPL) WE GRD REPAIR KIT WE OUTER GRD WE INNER GRD WE GRD REPAIR KIT WE YOKE, TB & SLIP SLEEVE WE 44R CROSS & BRG KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT & SFT HALF ASY W/GRD WE JOINT & TB HALF ASY W/GRD Obsolete 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 95
Table of Contents Driveline CV 540 RPM (826-643C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-30185 96 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline CV 540 RPM (826-643C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. Dwg 30185 826-643C 26-15120 68810-1004 03-15570 26-16033 99-24406 19-15135 97-24406 96-24406 98-24406 03-15316 55051-1817 11-14988 11-15180 93-24406 92-24406 91-24406 11-80005 Drawing Image Number DRVLN C6 42 38-6 CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT W/ CHAINS WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT.625-11 WE BOLT.625-11 X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET WE CHAIN (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 97
Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-25962 98 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. dwg25962 229829X0 396298 168556 391567 391350 391351 020452 803-280C 30005 020467 Drawing Image Number WS FRICTION CLUTCH * WS FLANGE YOKE WS FRICTION DISK WS HUB 1 3/4-20 I.C. WS THRUST PLATE WS BELLEVILLE SPRING WS HEX BOLT M10X50 NUT HEX NYLOCK M10X5 PLT COSMO WING NUT M8 WS HEX BOLT M12X65 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 99
Table of Contents Driveline Slip Clutch 540/1000 RPM (1446016) EC Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-15521 100 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Slip Clutch 540/1000 RPM (1446016) EC Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 dwg15521 1446016 1215012 1706033 1705009 1808010 1708034 1138008 1708016 6821484 1138007 6691010 330-297A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL * RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC PRESSURE DISK EC BOLT & SCREW NUT KIT REPL. SV KIT, EC SLIP CLUTCH SPRING Includes nut and washer Contains 8 Springs 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 101
Table of Contents Driveline Wing (826-185C) Eurocardan Applies to RC3615 S/N 945022- Section 5: Drivelines (540 RPM) 16366 102 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-185C) Eurocardan Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. 28. 29. dwg16366 826-185C 1786711 1215733 1885702 1215735 1885709 1877111 1876901 1885703 1786710 1446016 1006020 1706029 1526121 6331070 1528901 6331080 1706027 1016025 818-540C 818-552C 044321 6560508 1006220 6560006 1106025 6761480 6410114 6412114 826-581C Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD 1110MM EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD4/6 1 3/4 20 SPL EC CROSS ASSEMBLY EC INNER TUBE YOKE EC 1210MM INNER TUBE EC 10X70 ROLL PIN EC OUTER TUBE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSY 1 3/4-20(TRAC.END DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT(TRACT END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE EC BOLT EC SCREW NUT (M14) EC WASHER (d14) SHIELD KIT, 826-185C (S/N 928934-) Includes 27,28 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 103
Table of Contents Driveline Wing (826-185C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-25920 104 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-185C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. dwg25920 826-185C 229845X0 HM.243 020617 28133000 315892 384202 28133100 229829X0 105083 398294 398297 087276 044321 365305 355155 020466 30005 359471 Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20SPL I.C. WS CROSS & BRG KIT WS SPRING PIN 10 X 20 WS INBOARD YOKE 1B WS INNER PROFILE 1B 2400 WS PROFILE & SLEEVE W.A.1B/2AL WS INBOARD YOKE 2A WS FRICTION CLUTCH WS SHIELD CONE WS GUARD TUBE OUTER WS GUARD TUBE INNER WS BRG RING - SC25 DRIVELINE SHIELD SAFETY CHAIN WS SCREW WS SUPPORT BRG WS BOLT M12 X 60-8.8 COSMO WING NUT M8 WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 105
Table of Contents Driveline Wing (826-481C) Comer Applies to RC3615 S/N 945022- Section 5: Drivelines (540 RPM) 23953 106 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-481C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. dwg23953 826-481C 14028.195.1 180.018.004 15018.241 190.000.243 180.018.437 1522805450710 146.284.020.1 180.018.251 180.014.240 180.018.252 180.016.025 165.000.589 12580.021 12580.511 1422831949821 1422871029821 180.018.393 Drawing Image Number RPBY 826-812C * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE OUTER COMER OUTER TUBE ROLL PIN COMER WIPER COMER TUBE OUTER COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER COMER SAFTEY CHAINS COMER TAPERED PIN SET 1 3/4 COMER TUBE W/YOKE/LUBE/FEMALE COMER TUBE W/YOKE/LUBE/MALE COMER HALF FEMALE GRD W/LABEL COMER HALF MALE GUARDING COMER CAP OUTER TUBE, PLASTIC (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 107
Table of Contents Driveline Wing (826-481C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-25919 108 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-481C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. dwg25919 826-481C 325027 312209 304046 097133 323524 397493 097140 395980 377437 394874 387767 087276 044321 365305 396295 377436 702352 304011 359474 Drawing Image Number RPBY 826-812C * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS CROSS & BRG KIT 2500 WS SPRING PIN 10 X 90 WS INBOARD YOKE S4 WS INNER PROFILE S4L WS OUTER PROFILE S5L WS INBOARD YOKE S5 WS FRICTION CLUTCH WS SHIELD CONE 7 RIB WS OUT SHIELD TUBE OVL WS INNER SHIELD TUBE RND WS BRG RING - SC25 DRIVELINE SHIELD SAFETY CHAIN WS SCREW WS SUPPORT BEARING WS SHIELD CONE - 6 RIB WS HEX BOLT M16 X 90 GR 8.8 WS LOCK NUT M16 WS REINFORCING COLLAR (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 109
Table of Contents Driveline Wing (826-811C) Comer Applies to RC3615 S/N 945022- Section 5: Drivelines (540 RPM) 37509 110 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-811C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 Dwg 37509 826-811C 14026.357.1 180.016.780 146.264.024.1 8180.016.237 8180.014.240 8180.016.238 180.016.790 14260.5197621 165.000.589 180.014.022 15016.037.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 812360.504.11 812460.105611 190.000.098 190.000.099 190.000.903 Image No. DRVLN C4 50 75-20 FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET COMER CLUTCH, COMPLETE ASSY CO RETAINING COLLAR OUTER TUBE RPBY 180.014.240 CO RETAINING COLLAR INNER TUBE CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARD COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER CO LABEL W/CUSTOMER CODE (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 111
Table of Contents Driveline Wing (826-812C) Comer Applies to RC3615 S/N 945022- Section 5: Drivelines (540 RPM) 37553 112 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-812C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. 28. 29. 30. 3 3 3 34. 35. 36. 37. Dwg 37553 826-812C 14028.195.1 180.018.581 190.000.035 190.000.047 15018.241 190.000.243 150.285197810 159.280.168 190.000.271 15018.241 146.284.020.1 180.018.251 180.014.240 180.018.252 180.016.790 14286.2519821 165.000.589 180.014.022 15018.016.1 180.019.019 180.019.018 15018.228.1 180.019.014 180.019.115 180.019.116.1 165.000.548 12028.10301 12028.1025.01 14282509821 14287.2199821 12386.190.01 12486.3401 190.000.098 190.000.099 180.018.393 180.018.435 190.000.932 Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE OUTER COMER OUTER TUBE ROLL PIN CO COMPLETE OUTER TUBE W/LABEL COMER INNER TUBE COMER ROLL PIN FOR INNER TUBE COMER INNER YOKE COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY 180.019.340 COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO U-JOINT FOR OUTER TUBE CO U-JOINT FOR INNER TUBE CO HALF FEMALE GUARD CO HALF MALE GUARD CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER COMER CAP OUTER TUBE, PLASTIC COMER INNER CAP CO LABEL W/CUSTOMER CODE (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 113
Table of Contents Driveline Wing (826-812C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022-37502 114 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Driveline Wing (826-812C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 Dwg 37502 826-812C 325027 190224 097133 304046 323524 397493 097140 395980 125142 087276 371708 371709 399469 365305 383333 383334 044321 396295 380371 359474 125140 107542 Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20 SPL.I.C. 2500 WS CROSS & BEARING KIT WS INBOARD YOKE S4 WS SPRING PIN 10 X 90 WS INNER PROFILE S4L WS OUTER PROFILE S5L WS INBOARD YOKE S5 WS FRICTION CLUTCH WS GUARD CONE 7 RIB WS BRG RING - SC25 WS GUARD TUBE OUTER RPBY 371708 WS GUARD TUBE INNER WS SCREW RPBY 818-552C RPBY 818-540C DRIVELINE SHIELD SAFETY CHAIN WS SUPPORT BEARING WS ZERK WS REINFORCING COLLAR WS GUARD CONE 6 RIB CC LOCK ASSY (S/N 928934-) 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 115
Table of Contents Gearbox Center Deck (1000 RPM) (826-380C) Comer S/N 397434+ Applies to RCM3615 S/N 945022- Section 6: Gearboxes (1000 RPM) 22264 116 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Center Deck (1000 RPM) (826-380C) Comer S/N 397434+ Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 18. 19. 20. 2 2 2 24. 25. 26. 27. Dwg 22264 826-380C 0.210.20000 8.7.00331 8.5.00332 0.709.7500.00 8.0.9.00143 8.00501 0.210.5000.00 8.5.00533 8.6.5.00006 0.210.1300.00 0.257525.00 0.1271000 8.6.6.00201 8.4.7.02265 0.137107.00 0.210.6000.00 0.717500.00 04-011 8.0.9.00469 0.210.0300.00 8.7.01107 0.139.7100.00 0.210.3000.00 0.139.71000 8.00555 0.285.7510.00 8.4.7.00146 0.210.7100.00 Drawing Image Number GEARBOX COMER CO INPUT SHAFT 75-20 CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING 30209 RTA25 CO BOLT M10X22 HHB CO PINION Z18 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X5 CO GEAR CROWN Z22 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY REP BY 04-011 CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 67 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 117
Table of Contents Gearbox Divider 1000 RPM (826-281C) Comer Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022-19603 118 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Divider 1000 RPM (826-281C) Comer Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 Dwg 19603 826-281C 8.00449 8.7.00140 0.265.15000 822-189C 8.5.00332 8.7.00331 0.265.0300.00 0.267.7500.00 822-190C 0.265.5204.00 8.5.00680 822-188C 8.5.00030 0.2630000 8.7.00398 0.262004.00 8.5.01012 0.265.62000 0.709.7500.00 8.6.6.00201 8.6.7.00269 Drawing Image Number DIVIDER OMNI/CO 1000RPM RD * CO BOLT M8X30 8.8 CO SPRING WASHER 8.4X13X2 CO COVER T1 BALL BEARING 6209 CO SNAP RING UNI 7437 CO OIL SEAL 45 X 85 X 10 CO CASING CO SHIM 79.9 BALL BEARING 6307 CO GEAR Z24 CO SNAP RING 40 UNI 7436 BALL BEARING 6208 CO SNAP RING 80 UNI 7437 CO SHAFT 1 3/4-20 CO OIL SEAL 45 X 80 X 10 CO SHAFT 1 3/4 Z20 CO SNAP RING SW 47 CO PINION Z20 CO SHIM 84.7 CO PLUG 3/8 GAS CO 1/2" GAS BREATHER PLUG * Notes: Oil Type 80-90W Capacity 5 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 119
Table of Contents Gearbox Divider 1000 RPM (826-281C) OMN Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022-18581 120 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Divider 1000 RPM (826-281C) OMN Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. dwg18581 826-281C 110148 130058 020301 050302 200159 060168 010241 090332 090333 090334 050303 030666 200130 050007 200163 040463 060188 040462 200003 030667 090329 090330 090331 140011 140033 Drawing Image Number GBOX DIV. OMNI RCD90 3:1RD OMNI SCREW, M8X35 OMNI LOCKWASHER, M8 SPLIT TYPE OMNI COVER OMNI BEARING BALL 6209 OMNI RETAINING RING, 85mm OMNI SEAL-INPUT OMNI HOUSING, RCD-90 OMNI SHIM-OUTPUT 0.1mm OMNI SHIM-OUTPUT 0.2mm OMNI SHIM-OUTPUT 0.5mm OMNI BEARING BALL 6307 OMNI PINION, 20T OMNI RETAINING RING 40mm OMNI BALL BEARING 208K OMNI RETAINING RING, 80mm OMNI SHFT OUTPUT 75-20 SPLNE OMNI SEAL-OUTPUT OMNI SHAFT INPUT 75-20 SPLNE OMNI RETAINING RING OMNI GEAR, 26T OMNI SHIM-INPUT 0.1mm OMNI SHIM-INPUT 0.2mm OMNI SHIM-INPUT 0.5mm OMNI PLG-PIPE, SCKT HD. 3/8-18 OMNI PLUG VENT 1/2-14 NPTF * Notes: Oil Type 80-90W Capacity 5 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 121
Table of Contents Gearbox Divider 1000 RPM (826-281C) SD Engineering Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022-33916 122 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Divider 1000 RPM (826-281C) SD Engineering Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. dwg33916 826-281C 18-120 21-012 21-018 822-188C 21-008 02-223 05-049 21-037 02-222 05-050 04-136 03-309 07-025 03-310 09-004 09-052 04-112 17-042 17-043 17-044 17-045 17-046 17-047 20-124 09-011 06-038 07-022 Drawing Image Number DIV. OMNI/CO 1000RPM RD * SD HOUSING ITG RETAINING RING SD 40DIA SHAFT RETAINING RING BRG BALL 6208 SD RETAINING RING SD OUTPUT SHAFT SD OIL SEAL 45X80X10 SD RETAINING RING 85 SD THRU SHAFT SD OIL SEAL 45X85X10 SD BALL BEARING 209 SD 20 TOOTH GEAR SD M8 HELICAL SPRING LOCK WSHR SD 24 TOOTH GEAR SD 3/8-18 NPT SQ HEAD PLUG SD 3/8-19NPT SQ HEAD PLUG SD BALL BEARING 307 SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD INSPECTION CAP COVER ITG M18 X 5P PLUG VENTED SD M8X25X40 HEX HEAD CAPP SW ITG SEALING WASHER S/N 775017+ S/N 775016- S/N 775017+ S/N 775016-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 123
Table of Contents Gearbox Left Deck 1000 RPM (826-382C) Comer (S/N 397434+) Applies to RCM3615 S/N 945022- Section 6: Gearboxes (1000 RPM) 22267 124 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Left Deck 1000 RPM (826-382C) Comer (S/N 397434+) Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 18. 19. 20. 2 2 2 24. 25. 26. 27. Dwg 22267 826-382C 0.210.20000 8.7.00331 8.5.00332 0.709.7500.00 8.0.9.00143 8.00501 0.210.6000.00 8.5.00533 8.6.5.00006 0.210.1300.00 0.257525.00 0.1271000 8.6.6.00201 8.4.7.02265 0.137107.00 0.210.5000.00 0.717500.00 04-011 8.0.9.00469 0.210.0300.00 8.7.01107 0.139.7100.00 0.210.3000.00 0.139.71000 8.00555 0.285.7510.00 8.4.7.00146 0.210.7100.00 Drawing Image Number GEARBOX COMER CO INPUT SHAFT 75-20 CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING 30209 RTA25 CO BOLT M10X22 HHB CO GEAR CROWN Z22 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X5 CO PINION Z18 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY REP BY 04-011 CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 67 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 125
Table of Contents Gearbox Right Deck 1000 RPM (826-381C) Comer (S/N 397434+) Applies to RCM3615 S/N 945022- Section 6: Gearboxes (1000 RPM) 22266 126 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Right Deck 1000 RPM (826-381C) Comer (S/N 397434+) Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 17. 18. 18. 19. 20. 2 2 2 24. 25. 26. 27. Dwg 22266 826-381C 0.210.20000 8.7.00331 8.5.00332 0.709.7500.00 8.0.9.00143 8.00501 0.210.6000.00 8.5.00533 8.6.5.00006 0.210.1300.00 0.257525.00 0.1271000 8.6.6.00201 8.4.7.02265 0.137107.00 0.210.5000.00 A.71500 0.717500.00 04-011 8.0.9.00469 0.210.0300.00 8.7.01107 0.139.7100.00 0.210.3000.00 0.139.71000 8.00555 0.285.7510.00 8.4.7.00146 0.210.7100.00 Drawing Image Number GEARBOX COMER CO INPUT SHAFT 75-20 CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING 30209 RTA25 CO BOLT M10X22 HHB CO GEAR CROWN Z22 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X5 CO PINION Z18 M6 COMER SHIM KIT RPBY A.71500 (SHIM KIT) IGT BEARING ASSEMBLY RPBY BY 04-011 CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 67 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 127
Table of Contents Gearbox Center & Left Deck (540 RPM ) (826-378C) Comer S/N 378036+ Applies to RC3615 S/N 945022- Section 6: Gearboxes (540 RPM) 20931 128 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Center & Left Deck (540 RPM ) (826-378C) Comer S/N 378036+ Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. Dwg 20931 826-378C 0.210.1300.00 8.00501 8.5.00533 0.210.20000 0.1271000 8.5.00332 0.709.7500.00 8.0.9.00143 0.257525.00 8.6.6.00201 0.210.0300.00 0.137106.00 8.4.7.02265 0.210.50000 0.717500.00 04-011 0.210.30000 8.7.01107 0.139.7100.00 0.139.71000 8.00555 8.4.7.00146 8.7.00331 0.210.60000 0.210.7100.00 8.6.5.00006 Drawing Image Number GEARBOX COMER CO COVER CO BOLT M10X22 HHB CO SNAP RING 50 UNI7435 CO INPUT SHAFT 75-20 CO CAP CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING 30209 RTA25 CO SHIM 45.3X5 CO PLUG 3/8 GAS CO CASTING & MACHINE CO NUT M30 X 5 CO COTTER PIN B 5X60 CO PINION Z16 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY CO OUTPUT SHAFT CO SEAL (50x90x10) CO SEAL RETAINER CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO COTTER PIN B6 X 60 CO OIL SEAL 45 X 85 X 10 CO GEAR CROWN Z23 M6 CO 3/8 GAS OIL VENT LEVEL PG. CO OIL PLUG 3/8 * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 129
Table of Contents Gearbox Divider 540 RPM (826-280C) Comer Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N 945022-18782 130 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Divider 540 RPM (826-280C) Comer Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 Dwg 18782 826-280C 8.00449 8.7.00140 0.265.15000 822-189C 8.5.00332 8.7.00331 0.265.0300.00 0.267.7500.00 822-190C 0.265.52000 8.5.00680 822-188C 8.5.00030 0.2630000 8.7.00398 0.262004.00 8.5.01012 0.2650000 0.709.7500.00 8.6.6.00201 8.6.7.00269 Drawing Image Number DIVIDER OMNI/CO 540RPM SU * CO BOLT M8X30 8.8 CO SPRING WASHER 8.4X13X2 CO COVER T1 BALL BEARING 6209 CO SNAP RING UNI 7437 CO OIL SEAL 45 X 85 X 10 CO CASING CO SHIM 79.9 BALL BEARING 6307 CO PINION Z20 CO SNAP RING 40 UNI 7436 BALL BEARING 6208 CO SNAP RING 80 UNI 7437 CO SHAFT 1 3/4-20 CO OIL SEAL 45 X 80 X 10 CO SHAFT 1 3/4 Z20 CO SNAP RING SW 47 CO GEAR Z24 CO SHIM 84.7 CO PLUG 3/8 GAS CO 1/2" GAS BREATHER PLUG * Notes: Oil Type 80-90W Capacity 5 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 131
Table of Contents Gearbox Divider 540 RPM (826-280C) SD Engineering Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N 945022-33915 132 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Divider 540 RPM (826-280C) SD Engineering Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. Dwg 33915 826-280C 18-120 21-012 21-018 822-188C 21-008 02-223 05-049 21-037 02-222 05-050 04-136 03-180 07-025 03-181 09-004 09-052 04-112 17-042 17-043 17-044 17-045 17-046 17-047 20-124 09-011 06-038 07-022 Drawing Image Number DIV. OMNI/CO 540RPM SU * SD HOUSING ITG RETAINING RING SD 40DIA SHAFT RETAINING RING BRG BALL 6208 SD RETAINING RING SD OUTPUT SHAFT SD OIL SEAL 45X80X10 SD RETAINING RING 85 SD THRU SHAFT SD OIL SEAL 45X85X10 SD BALL BEARING 209 SD 24 TOOTH GEAR SD M8 HELICAL SPRING LOCK WSHR SD 20 TOOTH GEAR SD 3/8-18 NPT SQ HEAD PLUG SD 3/8-19NPT SQ HEAD PLUG SD BALL BEARING 307 SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD INSPECTION CAP COVER ITG M18 X 5P PLUG VENTED SD M8X25X40 HEX HEAD CAPP SW ITG SEALING WASHER S/N 775017+ S/N 775016- S/N 775017+ S/N 775016-07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 133
Table of Contents Gearbox Right Deck 540 RPM (826-379C) Comer (S/N 378036+) Applies to RC3615 S/N 945022- Section 6: Gearboxes (540 RPM) 22263 134 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Gearbox Right Deck 540 RPM (826-379C) Comer (S/N 378036+) Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. Dwg 22263 826-379C 0.210.20000 8.7.00331 8.5.00332 0.709.7500.00 8.0.9.00143 8.00501 0.210.60000 8.5.00533 8.6.5.00006 0.210.1300.00 0.257525.00 0.1271000 8.6.6.00201 8.4.7.02265 0.137106.00 0.210.50000 0.717500.00 8.0.9.00469 0.210.0300.00 8.7.01107 0.139.7100.00 0.210.30000 0.139.71000 8.00555 8.4.7.00146 0.210.7100.00 Drawing Image Number GEARBOX COMER CO INPUT SHAFT 75-20 CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING 30209 RTA25 CO BOLT M10X22 HHB CO GEAR CROWN Z23 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M30 X 5 CO PINION Z16 M6 CO SHIM 50.3X70.3 REP BY 04-011 CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 135
Table of Contents Hydraulic Cylinder (810-150C) Cross Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 7: Hydraulics 15572 136 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hydraulic Cylinder (810-150C) Cross Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. Dwg 15572 810-150C 1D1505-3 2A0235-6 2A0578-1675 1D0005-1450 2A0079-616 1D1551-16275 2A0308-1 1D1003-5 2A0235-6 1D0206-1675 1D1155-17 1D1401-250 2A0246-12 810-178C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * BASE CROSS CROSS NUT, CLEVIS & TIE ROD MW O-RING TIE ROD CROSS TUBE CROSS CROSS SCREW, CAP CROSS CLEVIS PIN CROSS PIN, CLIP CROSS ROD CLEVIS CROSS NUT, CLEVIS & TIE ROD ROD CROSS MW WIPER BACK-UP O-RING HEAD CROSS MW BACKUP CROSS PISTON CROSS NUT, PISTON SEAL KIT CROSS 5 CYL 1C4982 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 137
Table of Contents Hydraulic Cylinder (810-150C) Midway Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 7: Hydraulics 15572 138 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hydraulic Cylinder (810-150C) Midway Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 17. 18. 19. Dwg 15572 810-150C 6M3118 2A0012 7M3320 5M3120 2A0006 2A0208 2A0132 1M6010 2A0012 2M3418 3R0406 4M3108 4M3102 2A0022 810-177C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * MW BASE MW NUT CLEVIS & TIE ROD MW O-RING MW TIE MW TUBE MW CAPSCREW MW CLEVIS PIN MW PIN CLIP MW CLEVIS STD. DUTY MW NUT CLEVIS & TIE ROD MW ROD MW WIPER BACK-UP O-RING MW HEAD MW BACKUP MW PISTON RPBY 4M3108 MW NUT, PISTON SEAL KIT MW 5X25ROD 3A3104 Only found in seal kit 19 ROD Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 139
Table of Contents Hydraulic Cylinder (810-150C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-25899 140 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hydraulic Cylinder (810-150C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. Dwg 25899 810-150C 803-014C 130556 134953 135995 801-023C 186561 N/A N/A N/A N/A N/A N/A 491672 492222 492647 492650 492688 494286 258818 810-886C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * NUT HEX 3/8-16 PLT MON PISTON NUT LION PIN MON CLEVIS PIN COTTER SCREW SET SH 3/8-16X3/8 TYPE C PLUG 9/16-18UNF MORB SOCKET HD MON ROD SEAL MON PISTON SEAL MON END CAP BACKUP WASHERS MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING LION CYL TUBE 5 X 12 LION TIE ROD 3/8, 12 CYL LION ROD 25 X 12 LION ROD CLEVIS 1 1/8-12UNF LION CLEVIS CAP 5, 9/16 ORB MON ROD CAP5-25-3/4ORB-TSS MON PISTON50-.750-TSS-ISO-WR MON SEAL KIT 661701 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 141
Table of Contents Hydraulic Cylinder (810-624C) Midway Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 7: Hydraulics 12499 142 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hydraulic Cylinder (810-624C) Midway Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. Dwg 12499 810-624C 6R1164-ADI 6M4166 2A0014 7M4316 5M4116 2A0006 1M6010-ADI 2A0012 2M4416 3M4412 4M4104 2A0024 810-015C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * MIDWAY ADI BASE RPBY 6R1164-ADI MW TIE ROD NUT O-RING MW TIE ROD 3 X 8 CYLINDER MW TUBE 3 X 8 CYLINDER MW CAPSCREW MIDWAY HARDENED CLEVIS ADI MW NUT CLEVIS & TIE ROD MW ROD 1-1/4 DIA X 8 STROKE WIPER BACK-UP O-RING MW HEAD CAP 3X1-1/4 ROD 3/4SAE BACK-UP MW PISTON 3 DIA. MW PISTON NUT 1-14 CYL SEAL KIT 3 X 7 MW 3A4104 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 143
Table of Contents Hydraulic Cylinder (810-624C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-25896 144 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hydraulic Cylinder (810-624C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. Dwg 25896 810-624C 803-020C 130560 801-023C 186562 N/A N/A N/A N/A N/A N/A 292003 258818 491738 492278 494391 492675 493211 493830 810-887C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * NUT HEX 1/2-13 PLT MON PISTON NUT SCREW SET SH 3/8-16X3/8 TYPE C LION PLUG 3/4-16UNF SOCKET HD MON ROD SEAL MON PISTON SEAL (PSP) MON END CAP B/U WASHER MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING MON TIE ROD EXTND THD MON PISTON50-.750-TSS-ISO-WR MON CYL TUBE MON TIE ROD MON ROD CP50-12-9/16ORB-TS MON CLEVIS CAP MON CYL ROD LION HARDENED ROD CLEVIS 1 1/4 MON SEAL KIT 661702 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 145
Table of Contents Hydraulic Lift Components Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Section 7: Hydraulics 70305 146 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18
Table of Contents Hydraulic Lift Components Section 7: Hydraulics Applies to RC3615 S/N 945022-, RCM3615 S/N 945022- Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. Dwg 70305 318-018H 318-648D 800-306C 802-017C 802-684C 803-209C 804-011C 804-012C 804-013C 804-029C 805-088C 805-104C 807-023C 810-150C 810-624C 810-818C 811-062C 811-063C 811-309C 811-356C 811-394C 811-619C 811-633C 235005 Image No. WLDMT. CYLINDER PIN TRANSPORT BAR FILL PLUG VENTED 3/4-16 PLT HHCS 3/8-16X1 GR5 HHCS M8X25X55 GR8.8 NUT FLANGE LOCK 3/8-16 PLT WASHER FLAT 3/8 USS PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 1 SAE PIN, HAIR COTTER 3/16 WIRE DIA PIN COTTER 3/16 X 1 1/2 PLT SPRING HOSE LOOP CYL 5X12X25 ROD (TIE ROD) CYL 3X8X25 ROD (TIE) NO PINS STRK CNTRL SPCRS 125 TO 50 OREL 1/32 9/16MJIC 9/16MORB EL 3/4MJIC 3/4MORB HH1/4R1 066 9/16FJIC TE 9/16MJIC BH 9/16MJIC 9/16MJ CP 3/4FORB MALE QD POPPET TYPE HH3/8R1 168 3/4MORB 3/4FJIC HH3/8R1 162 3/4MORB 9/16FJIC MON PIN KIT 00C/W COTTER PIN Includes 2 clevis pins & 4 cotter pins 07/10/18 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 147
Decal Placement Table of Contents Section 8: Decals Applies to RC3615 S/N 945022-, RCM3615 S/N 945022-27714 148 RC(M)3615 S/N 945022- Rotary Cutters 330-502P 07/10/18