Highly reliable iniature Basic Switch in spite of its Ultra-low Load action Twin crossbar contact employed for exceptionally high contact reliability. Unique internal mechanism that ensures high contact reliability even in micro load operations. pplicable for detection of light objects. RoHS Compliant Number Legend -@@- 1 @@@ 3 4 5 1. Ratings 1: 15 C 1 01: 30 C 0.1. ctuator None : Pin plunger L11 : Short hinge L : Hinge L111 : Long Hinge Lever L13 : Simulated roller L : Short hinge roller Lever L : Hinge roller Lever 3. Contact form 1: SPT 4. Terminals C: Solder terminals 5. aximum Force (OF) 1: 0.10 N {10 gf} (for pin plunger models only) : 0.5 N {5 gf} (for pin plunger models only) 3: 0.49 N {50 gf} Note. These values are for the pin plunger models. List of s ctuator Pin plunger Short hinge Ratings ax. Force (OF) 1 0.1 0.10 N {10 gf} -1-1C1-01-1C1 0.5 N {5 gf} -1-1C -01-1C 0.49 N {50 gf} -1-1C3-01-1C3 0.49 N {50 gf} -1L11-1C3-01L11-1C3 Hinge 0.9 N {30 gf} -1L-1C3-01L-1C3 Long hinge Simulated roller Short hinge roller 0.15 N {15 gf} -1L111-1C3-01L111-1C3 0.9 N {30 gf} -1L13-1C3-01L13-1C3 0.49 N {50 gf} -1L-1C3-01L-1C3 Hinge roller 0.9 N {30 gf} -1L-1C3-01L-1C3 Contact Form SPT NC NO CO Separator (Sold Separately), ctuator (Sold Separately), Terminal Connector (Sold Separately) Refer to "Basic Switch Common ccessories" 1
Contact Specifications Item -1 models -01 models Specification Needle Twin crossbar Contact aterial Silver Gold alloy Gap (standard value) 0.5 mm Inrush NC current NO inimum applicable load (reference value) * 5 C 30m 5 C 1m * Please refer to " Using icro Loads" in "Precautions" for more information on the minimum applicable load. Ratings Characteristics -1 models -01 models Rated voltage Item Resistive load 15 C 1 0.1 30 C 1 0.1 Note. The above rating values apply under the following test conditions. (1) mbient temperature: 0± C () mbient humidity: 65±5% (3) frequency: 30 operations/min pproved Safety Standard UL (UL1054) /CS (CS C. No.55) Rated voltage -1-01 15 C 1 0.1 30 C 1 0.1 Item -1 models -01 models Permissible operating speed 1 mm to 1 m/s (for pin plunger models) Permissible echanical 300 operations/min (for pin plunger models) operating frequency Electrical 60 operations/min Insulation resistance 100Ω min. (at 500 C with insulation tester) Contact resistance (initial value) 30 mω max. 50 mω max. Between terminals of the same 1,000 C 50/60 Hz 1min polarity ielectric strength * 1 ibration resistance * Shock resistance urability * 3 Between current-carrying metal parts and ground Between each terminal and non-current-carrying metal parts 1,500 C 50/60 Hz 1min 1,500 C 50/60 Hz 1min alfunction 10 to 55 Hz, 1.5 mm double amplitude s with OF of 0.10N urability s with OF between 0.5 to 0.49N alfunction * echanical Electrical egree of protection mbient operating temperature mbient operating humidity Weight 150 m/s {approx. 15G} max. 400 m/s {approx. 40G} max. 100 m/s {approx. 10G} max. 10,000,000 operations min. (60 operations/min) 500,000 operations min. (30 operations/min) IEC IP40 1,000,000 operations min. (30 operations/min) 5 C to +80 C (at ambient humidity of 60% max.) (with no icing or condensation) 85% max. (for +5 C to +35 C) pprox. 6g (pin plunger models) Note. The data given above are initial values. *1. The values for dielectric strength shown are for models with a Separator (refer to "icro Switch Common ccessories"). *. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel Position value for. Close or open circuit of the contact is 1ms max. Terminals/ppearances (Unit:mm) ounting Holes (Unit: mm) (6.5) (6.3) -3.1 dia. mounting holes or 3 screw hole 7.5 3.9 3. 6.3 1. 4.75±0.1.4 dia. 1.3 dia.
imensions (Unit: mm) / Characteristics Pin plunger s -1-1C@ -01-1C@ 0.±0.5 dia. holes 15.9 11.6 19.8±0.8 4. 4 (7.5) Note. The @ in the model number is for the OF code. Force OF ax. Releasing Force RF in. ax. OT in. ovement ifferential ax. -1-1C1-01-1C1 0.10N {10 gf} 0.005N {0.5 gf} -1-1C -01-1C 0.5N {5 gf} 0.01N {1 gf} 1. mm 1.3 mm 0.5 mm Position 14.7±0.4 mm -1-1C3-01-1C3 0.49N {50 gf} 0.0N { gf} Short Hinge Lever s -1L11-1C3-01L11-1C3 * Stainless-steel *.1 8.1 dia. holes 4 (7.5) -1L11-1C3-01L11-1C3 Force OF ax. 0.49N {50 gf} Releasing Force RF in. 0.04N {4 gf} (reference value) ax. 1.7 mm OT in. 1.0 mm ovement ifferential ax. 0.4 mm Position 15.±0.5 mm Hinge Lever s -1L-1C3-01L-1C3 35.6±0.8 * 8.1 dia. holes * Stainless-steel 4 (7.5) -1L-1C3-01L-1C3 Force OF ax. 0.9N {30 gf} Releasing Force RF in. 0.0N { gf} (reference value) ax. 3.3 mm OT in..1 mm ovement ifferential ax. 0.7 mm Position 15.±1. mm Long Hinge Lever s -1L111-1C3-01L111-1C3 59.4±0.8 * 8.1 dia. holes 4 (7.5) * Stainless-steel -1L111-1C3-01L111-1C3 Force OF ax. 0.15N {15 gf} Releasing Force RF in. 0.01N {1 gf} (reference value) ax. 6.0 mm OT in. 4.0 mm ovement ifferential ax. 1.4 mm Position 15.±.6 mm Simulated Roller Lever s -1L13-1C3-01L13-1C3 4 (7.5) Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note. The operating are for operation in the direction ( ). R3.5 3.6±0.8 * 8.1 dia. holes * Stainless-steel -1L13-1C3-01L13-1C3 Force OF ax. 0.9N {30 gf} Releasing Force RF in. 0.0N { gf} (reference value) ax. 3.3 mm OT in. 1.9 mm ovement ifferential ax. 0.7 mm Position 18.7±1. mm 3
Short Hinge Roller Lever s -1L-1C3-01L-1C3 Hinge Roller Lever s -1L-1C3-01L-1C3 4.8 dia. 4.8 * *1 0.1 5.1 4.8 dia. 4.8 * 34.8±0.8 *1 8.1 8.1 dia. holes 4 (7.5) dia. holes 4 (7.5) * 1. Stainless-steel *. Polyacetal resin roller * 1. Stainless-steel *. Polyacetal resin roller 5.1-1L-1C3-01L-1C3 Force OF ax. 0.49N {50 gf} Releasing Force RF in. 0.04N {4 gf} (reference value) ax. 1.7 mm OT in. 1.0 mm ovement ifferential ax. 0.4 mm Position 0.7±0.6 mm -1L-1C3-01L-1C3 Force OF ax. 0.9N {30 gf} Releasing Force RF in. 0.0N { gf} (reference value) ax. 3.3 mm OT in..1 mm ovement ifferential ax. 0.7 mm Position 0.7±1. mm Note 1. Unless otherwise specified, a tolerance of ±0.4mm applies to all dimensions. Note. The operating are for operation in the direction ( ). Precautions Please refer to "Basic Switches Common Precautions" for correct use. Cautions Handling o not apply excessive shock. oing so may cause damage to the Switch's internal components because they designed for a small load. Soldering Terminal connections Complete the soldering at the iron tip temperature between 50 to 350 C (60W) within 5 seconds, and do not apply any external force for 1 minute after soldering. pply minimum amount of flux required. It may result in contact failure once the flux penetrates into the internal part of the Switch. Correct Use ounting Use 3 mounting screw with plane washers or spring washers to securely mount the Switch. Tighten the screws to a torque of 0.39 to 0.59 N m {4 to 6 kgf cm}. ounting irection For a Switch with an actuator, mount the Switch in a direction where the actuator weight will not be applied to the Switch. Since the Switch is designed for a low operating force, its release force is low. Therefore, release failure may occur if unnecessary force is applied to the Switch. Using icro Loads Using a model for ordinary loads to open or close the contact of a micro load circuit may result in faulty contact. Use models that operate in the following range. However, even when using micro load models within the following operating range, if inrush current occurs when the contact is opened or closed, it may increase the contact wear and so decrease durability. Therefore, insert a contact protection circuit where necessary. The minimum applicable load is the N-level reference value. This value indicates the malfunction reference level for the reliability level of 60% (λ60). (JIS C5003) The equation, λ60=0.5 10-6 / operations indicates that the 1 estimated malfunction rate is less than operations,000,000 with a reliability level of 60%. oltage () 0.16 m 30 4 1 5 0 0.1 1 m 5 m icro load type range -01 30 m 100 m Normal load type range -1 1 10 100 1,000 Current (m) 4
pplication examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. Consult your ORON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. ake sure that the ratings and performance of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: o not use this document to operate the Unit. ORON Corporation ELECTRONIC N ECHNICL CONENTS CNY Contact: www.omron.com/ecb Cat. No. B018-E1-09 081(007)(O) 5