Original & T Series 8 Bores, /2" 4" Section Index Features & Benefits....2 General, Standard Specifications....2 Page Construction Details....3,.4 How a Pancake is built Information....5,.6 How a Pancake Functions Option Information....7 -.4,.65,.66 Description of Options Custom Options and Specials....5 Air Spring....5 Accessories Flow Controls, Port Mounted and Others....6 Position Sensors....4,.6 Mounting Bolts....6 Wrench Flat Wrench....6 Detailed Specification Model Number Codes How to Order Standard Dimensions Seal Kit Part Numbers Magnetic Piston Position Sensing Option Dimensions /2" (5) Bore....7 -.22 3/4" (7) Bore....23 -.28 -/8" (2) Bore....29 -.34-5/8" (22) Bore....35 -.40 2" (32) Bore....4 -.46 2-/2" (52) Bore....47 -.52 3" (72) Bore....53 -.58 4" (22) Bore....59 -.64 Flow Controls Port Mounted and Others... Section 2 Specials... ii, iii 2 Year Warranty... Inside back cover. 4-22-04
Original & T Series 8 Bores, /2" 4" Features & Benefits This, the original Pancake Cylinder, was designed in 958 to satisfy the need for short stroke cylinders that would fit in very tight spaces. Today, with almost four decades of experience in thousands of cylinder applications around the world, The Pancake Line offers you far more than any of its imitators more features and options better quality, strength and appearance and far longer product life! Original Series We are so confident in our design and manufacturing skills that we back every Pancake Cylinder with our 2-year Warranty! Features Benefits Machined from aluminum bar-stock... Strength, precision & clean lines Heavy wall construction... Bore protection Internally lubricated O-rings... Smooth operation & long life Original Series Duralon nonmetallic rod bushing... Superior bushing & rod life Hard chrome plated stainless steel piston rod... Long life, corrosion resistance Crosshatch polished bore... Lubrication retention for seal life More bores, strokes, options... Fit your application Original Series, Nonrotating Clear anodized... Appearance & corrosion resistance Internal guide pins in non-rotating... Protected from environment Prelubed with Magnalube -G Grease... Long life, smooth operation "T" Series... Includes PTFE piston bearing 2 Year warranty.... Extended buyer protection T Series Laboratory tests confirm that internally lubricated Buna-N O-ring seals have extended Pancake cylinder life 2 to 3 times beyond that of cylinders using standard Buna-N seals. General, Standard Specifications Media... Air... Optional - Hydraulic Maximum operating pressure... 250 psi... Optional - 500 psi Minimum operating pressure... See page.4, Item 4 Ambient & media temperature... 25 to + 250 F Prelubrication...Magnalube -G Grease Air line lubrication...recommended tolerance...± /64" 4-22-04.2
Original & T Series 8 Bores, /2" 4" Original Series Construction Details P'Cake X Cuta 0-4-0 9 0 4 3 0 4 2 9 8 9 6 7 4 5 Single Rod Double Acting - X /2" & 3/4" Bores Single Rod - Double Acting -X shown P'Cake XDR Cuta 0-4-0 6 5 8 7 4 Single Rod Double Acting P'Cake XK Cuta - X 2/30/97 9 0 4 3 0 4 2 3 0 4 2 9 3 2 4 3 9 2 8 9 5 8 6 4 9 0 6 0 4 3 4 6 6 7 4 5 Double Rod Double Acting - XDR /2" & 3/4" Bores Double Rod Double Acting - XDR Single Rod Double Acting Nonrotating - XK 2/29/97 P'Cake X T-Cuta 0/4/0 T Series (PTFE Piston Bearing) P'Cake XK T-Cuta 2/30/97 9 0 4 3 0 4 2 3 0 4 2 9 8 4 9 8 9 5 8 6 7 4 5 6 8 7 4 5 4 6 6 7 4 5 4.3 Single Rod Double Acting - X /2" & 3/4" Bores Single Rod Double Acting - X Single Rod Double Acting Nonrotating - XK 4--08
Original & T Series 8 Bores, /2" 4" Construction Details Nearly 4 decades of experience paying close attention to design detail, production and assembly techniques have resulted in the ultimate Fabco-Air Pancake, short stroke cylinders. Pancakes fit into very tight spaces and virtually ANY short stroke cylinder application. Think how well they will fit with your application!. The heavy wall prohibits any damage to the bore from external forces. 2. The one piece cylinder body and bushing support end is machined from solid aluminum bar-stock. This provides unequalled strength, rigidity, and piston rod support. Machining all surfaces provides perpendicularity and concentricity for locating, mounting, and making attachments to the rod. It also presents a clean, smooth, "no-dirtcatching" appearance on your machine. 3. Unique construction provides unequalled piston rod support and prohibits Blowout! The one piece Duralon rod bushing is inserted from the inside and then staked in place. Duralon is a Teflon lined fiberglass structure with a load carrying capacity of 60,000 psi. Compare capacity with Nylon at,000 psi, porous bronze at 4,500 psi, and porous iron at 8,000 psi. Duralon also provides: CONSIS- TENCY, reliable and predictable performance from bushing to bushing; CORROSION RESISTANCE, nonmetallic materials resist galvanic, chemical and fretting corrosion; SELF LUBRICATION, Teflon lining provides low friction and minimizes stickslip, even under no-lube conditions; SEIZURE RESISTANCE, fiberglass backing material will not seize or gall on shaft under extreme wear. Generally the bearing length is increased as the stroke increases, providing even more piston rod support. 4. Internally lubricated Buna-N O'Rings (-25 to + 250 F) provide low profile, low friction, and long life sealing of piston and rod. All static seals are Buna-N. These dynamic O'Rings are compounded to provide extra long wear and lower breakaway (starting) and running friction and smoother operation. In tests, cylinders with internally lubricated O'Rings have extended cycle life two to three times beyond cylinders with standard Buna-N seals. The chart below shows maximum breakaway or starting pressure to extend the rod of single rod, double acting ( -X) cylinders with internally lubricated O'Rings under no-load conditions after 3 days delay at zero pressure. With other actions and/or combinations of options, breakaway pressures may vary. Bore Number 5 7 2 22 32 52 72 22 Bore, Inches /2 3/4 -/8-5/8 2 2-/2 3 4 Breakaway psi 2.0 6.5 4.5 4.5 4.0 3.0 3.0 2.5 These low operating pressures allow for the use of vacuum as an Operating Media in many applications..0 psi is the equivalent of 2.04" Hg of vacuum. To determine the force output of a cylinder with vacuum, multiply: Force Area of cylinder x inch Hg vacuum x 0.49 = Force, lb. 5. The thinnest possible piston and rear cover design keeps the overall height as short as possible. Please note that any cylinder offering less height than that of a Pancake with the same stroke, sacrifices rod bushing length and/or overall strength. 6. The aluminum cover is held in place with multiple plated screws for strength, rigidity, ease of modification for specific application requirements, and ease of access for maintenance should it be required. 7. The aluminum piston is attached to the piston rod with a socket flat head cap screw which is torqued for proper preload on the screw and clamping of the piston. Loctite on the threads and faces assures sealing and locks the assembly against pounding and vibration. 8. The piston in all bores has a counterbore for piston rod location and control of concentricity between piston rod and piston O.D. 9. Polishing the cylinder bore and piston rod produces a fine crosshatched finish. This crosshatching provides minute oil ring type grooves for retaining lubrication. This finish, unlike an ultra smooth finish, provides a place for lubrication to lie and support the seal as it moves along the surface. The surface finish and lubrication provide lower friction and longer seal life. 0. The piston rod is centerless ground, polished, and hard chrome plated (68-72 Rc) stainless steel. Surface finish is 2 RMS or better and carries lubrication like our cylinder bore (see 9). These features combined with the low friction and high load capacity of the Duralon bushing provide exceptional cylinder life. Female, fine pitch rod thread and wrench flats are standard.. A pilot diameter on the cover is concentric with the rod bushing and locates in the cylinder bore to maintain the concentricity, precision, and rigidity of the Pancake design. 2. Counterbores on both sides of the piston maintain concentricity of piston rods to each other as well as to the piston O'Ring. This also provides complete axial and radial rigidity of the piston so that it cannot float or be pounded loose. 3. The piston rods are connected by a high strength stud, sandwiching the piston between the rod end faces. The assembly is torqued for proper preload of the stud and clamping of the piston head. Loctite on the threads and faces assures sealing and locks the assembly against pounding and vibration. This procedure provides a positive and rigid assembly that will not allow the piston to float or be pounded loose. 4. The "T" Series has a thicker piston which incorporates a bearing strip in addition to the O-ring seal. This bearing strip is a close tolerance, rectangular cross section strip of a tough, stable, wear resistant PTFE compound. If the piston rod assembly is forced off center by misalignment or other forces, this bearing, along with the long and rigid Duralon rod bushing, supports the load and helps to maintain the long life of the cylinder bore and O-ring seal. Note: the bearing is not included, or required in double rod models because the long rod bushings at each end of the cylinder provide superb support. 5. Two guide pins of precision ground tool steel pass through the piston head. These guide pins prevent rotation of the rod with a tolerance of ±. Note that the guide pins are located internally. This provides protection from the environment and from physical damage. Lubrication is provided with other internal parts. NO additional space is required and the rod end is left free for attachments and tooling as required by the application. An information label, similar to this one, is applied to each cylinder to warn against damage. WARNING THIS CYLINDER HAS A NONROTATING ROD. TO PREVENT INTERNAL DAMAGE HOLD ROD BY WRENCH FLATS WHEN INSTALLING OR REMOVING ATTACHMENTS 6. The guide pins pass through Polyurethane O'Ring seals and SAE660 bearing bronze bushings incorporated in the piston head. This combination provides no leak, precision guiding and long life. 8. A disk of rubber is included at the end of the guide pins to take up play and firmly seat the pins in the precision machined guide pin holes. 9. Integral rod bearing and endcap is hard anodized aluminum. The piston rod seal O-ring is located as close to the outer end as feasible so that as much of the bearing as possible gets system lubrication as well as protecting most of the bearing length from the environment. A precision machined pilot diameter locates the cylinder bore to assure concentricity and proper rod alignment. 2-3-08.4
Original & T Series 8 Bores, /2" 4" Information Original Series C-22-X T Series PTFE Piston Bearing TC-22-X NFPA Symbol Letter Description -X Single Rod Double Acting One Piston Rod Power Extend - Power Retract C-22-XK TC-22-XK -XK 50 psi maximum Single Rod Double Acting Nonrotating One Piston Rod Power Extend - Power Retract Piston guide pins for nonrotating C-22-O TC-22-O -O Single Rod Single Acting - Spring Retracted One Piston Rod Power Extend - Spring Retract C-22-OP TC-22-OP -OP Single Rod Single Acting - Spring Extended One Piston Rod Spring Extend - Power Retract.5 4-22-04
Original & T Series 8 Bores, /2" 4" Information The Letter portion of the Pancake Model Number specifies how many piston rods the cylinder has (Single Rod or Double Rod), how the piston rod is extended and retracted (Double Acting or Single Acting), and if the piston rod is restricted from rotating by internal guide pins (Nonrotating). Original Series T Series PTFE Piston Bearing NFPA Symbol Letter Description C-22-XDR The T Series is not required in the double rod version. Two rod bushings provide superb rod support -XDR Double Rod Double Acting Two Piston Rods - One each end Power Extend - Power Retract C-22-XDRK The T Series is not required in the double rod version. Two rod bushings provide superb rod support -XDRK 50 psi maximum Double Rod Double Acting Nonrotating Two Piston Rods - One each end Power Extend - Power Retract Piston guide pins for nonrotating C-22-ODR The T Series is not required in the double rod version. Two rod bushings provide superb rod support -ODR Double Rod Single Acting - Spring Retracted Two Piston Rods - One each end Power Extend - Spring Retract 4-8-04.6
Original & T Series 8 Bores, /2" 4" Option Information PREFIX OPTIONS MODEL NUMBER METRIC Cylinder and Rod Thread. is standard. Optional Male Rod Thread add suffix -MR Prefix M PREFIX OPTIONS Mounting holes and rod thread are configured to common METRIC sizes. Ports in /2" (5) and 3/4" (7) bores are M5. Ports in -/8" (2) bore and larger are G/8 with 4mm spotface for /8 BSP-Parallel fittings and gaskets. Available on all series, bore, stroke and action combinations. See Option Specifications pages of desired bore and action for complete dimensional details..7 4-23-04
Original & T Series 8 Bores, /2" 4" Option Information SUFFIX OPTIONS MODEL NUMBER SUFFIX MALE ROD THREAD Single Rod Double Rod, Rod End Only Double Rod, Cap End Only Double Rod, Both Ends -MR -MR -MR -MR2 SUFFIX OPTIONS A high strength stud is threaded into the standard female rod end and retained with Loctite. This method eliminates the small diameter thread relief area normally required when machining male threads. This provides a much stronger rod end which can be repaired, rather than replacing the complete rod, should the thread be damaged. Available on all series, bore, stroke and action combinations. See Option Specifications pages of desired bore and action for complete dimensional details. TEFLON O'RING SEALS (+400 to +500 F) -T For elevated temperatures (+400 to +500 F) or compatibility with exotic medias. Consult engineering for compatibility information. NOTE: Teflon seals are NOT for low friction. This seal material assumes the shape of the rectangular groove, exhibits no memory and will not return to round O'Ring cross section. Therefore the piston and rod seals may exhibit some leakage. This is even more pronounced in applications that require thermal cycling over wide temperature ranges. They are not, therefore, recommended for such applications. Available on all series, bores -/8" (2) and larger, all strokes and actions -X, -XDR. See Standard Specifications pages of desired bore and action for complete dimensional details. There are no dimensional changes from standard. VITON O'RING SEALS (-5 to +400 F) -V For elevated temperatures ( 5 to + 400 F) or compatibility with exotic medias. Consult engineering for compatibility information. Available on all series, bore, stroke and action combinations. See Standard Specifications pages of desired bore and action for complete dimensional details. There are no dimensional changes from standard. QUAD SEALS (-30 to +250 F) -Q A QUAD seal replaces the standard O'Ring on the piston only. Standard seal material is Buna-N (-30 to +250 F). For other materials consult engineering. Available on all series, bore, stroke and action combinations. See Standard Specifications pages of desired bore and action for complete dimensional details. There are no dimensional changes from standard. Nonrotating Single Acting For Double Acting, Nonrotating SEE -XK, -XDRK on pages.5 and.6 4-23-04 -NR A Hex Rod of stainless steel in a broached, hard anodized aluminum endcap replaces the round rod in Single Acting, Spring Retracted (s -O, -ODR) cylinders. Available in all series, bores /2" (5), 3/4" (7), all strokes, actions -O, -ODR. See Option Specifications pages of desired bore and action for complete dimensional details..8
Pancake Cylinders SUFFIX OPTIONS Model Number Hydraulic, Low Pressure Service to 500 psi NONSHOCK. Temperature to +300 F max. Consult factory for media compatability and operating temperatures over 300 F. With Standard Thickness Cover -H With Thick Cover U-Cup Rod Seal SUFFIX DURALON Rod Bearing -HHC Original & "T" Series 8 Bores, /2" 4" Construction Details SUFFIX OPTIONS For Air-Oil or Hydraulic systems to 500 psi NONSHOCK.. A specially formulated U-Cup seal replaces the O-ring piston rod seal. This eliminates leakage past the rod seal and around the bushing. 2. Option -HHC, on single rod bores -5/8" (22) & larger, includes a thicker rear cover to assure that there is no warpage or failure when the mounting surface is the. See chart below. 3. /4 NPT Ports are available on bores -5/8" (22) & larger. See Option -P4 below. 4. Single Acting (Spring Return) Cylinders are designed for the spring to return the piston & rod assembly. Because of the low return forces available & the somewhat restricted flow, the piston returns slowly when used with oil at any pressure. Double Acting Cylinders are therefore recommended for Hydraulic service. H is available on all series, bores -/8" (2) and larger, actions -X & -O, -OP, -XDR & -ODR, all strokes. Available also for s -XK & -XDRK on bores 2-/2" (52) and larger. Consult factory for available strokes on bores -/8 (2) to 2" (32) and actions -XK & -XDRK. -HHC is available on all series. Bores -5/8" (22) and larger, all strokes, s -X & -O. SEE Option Specifications pages of desired Bore & for complete dimensional details. OPTION H H H H H HHC ACTION X, O OP XDR, ODR XK XDRK X, O Mounting surface is at rod end 250 500 500 50 50 500 Mounting surface is at cap end Pressure Ratings (psi) for Various Mountings 500 500 500 50 50 500 Other Options in Combination with H or HHC F 250 500 500 50 50 500 PM 500 500 NA 50 NA NA SM 500 500 NA 50 NA NA EPM 500 500 NA 50 NA NA ESM 500 500 NA 50 NA NA AS 500 NA NA 50 NA NA RS 500 500 NA 50 NA NA AIR SERVICE With Thick Cover -HC -HC includes the thick rear cover. It is for AIR service, to 250 psi, the thick rear cover is desired. when Available on all series, Bores 5/8" (22) and larger, all strokes, s; -X, -O. See Option Specifications pages of desired Bore and for complete dimensional details..9 /4 NPT PORTS -P4 Port size /4 NPT. On bores -5/8" (22) and 2" (32) the orifice between the port and the bore is also increased. All ports are in the standard locations. Use when reduced pressure drop or higher cycle speeds are desired. They are particularly advantageous in Air-Oil Hydraulic applications. Available on all series, bores -5/8" (22) & larger, all strokes, all actions. See Standard Specifications pages of desired bore & action for complete dimensional details. There are no dimensional changes from standard other than port size. 4-23-04
SUFFIX OPTIONS Hole Thru Double Rod Shaft Standard Standard Plus Model No. Model No. Hole Size Suffix Hole Size Suffix Bore thru stud (Std) thru stud (Std Plus) /2", 3/4" /6-06 -/8" /8-3 5/32-6 -5/8" /8-3 /4-25 2" 5/32-6 5/6-3 2-/2" 5/32-6 /4-25 3" 5/32-6 /4-25 4" /4-25 Rod Piston Rod Stud Original & "T" Series 8 Bores, /2" 4" Option Information SUFFIX OPTIONS 50 psi maximum operating pressure A hole is drilled through the piston rods & the double rod stud (see construction details on page.3). This hole is used for the passage of Vacuum, Air, Gas, Oil, Liquid or any media that is compatible with the stainless steel piston rod and the steel stud. Maximum pressure, 50 psi. Hole sizes available for each bore size are shown in the chart to the left. If a larger hole is needed (for higher flows or mechanical members) or all stainless steel construction is needed (for compatibility or higher pressure) see "One Piece Piston & Rod Construction" under Custom Options on page.5. Insert the SUFFIX Number into the Model Number immediately after the desired. For example: -XDR3 Available on Original Series, all Bores, all s, ; -XDR, -XDRK, -ODR. See Standard Specifications pages of desired Bore & for complete dimensional details. There are no dimensional changes from standard. FINISH: Clear anodize is standard. Plating: Pro-Coat Electroless Nickel -N Pro-Coat, Electroless Nickel Plating, is a hard, smooth, corrosion and wear resistant coating. It will often suffice for applications where stainless steel is specified. Its lasting luster provides high visual appeal. The coating is a high nickel, low phosphorous alloy deposited by chemical reduction without electric current that is mil-for-mil more corrosion resistant than electroplated nickel. The surface is virtually pore free. The thickness of the nickel deposit is consistent over the entire surface. Blind holes, threads, small diameter holes and internal surfaces all receive the same amount of plating. It has natural lubricity and a high resistance to abrasion. As shipped hardness of the coating is approximately 49 Rockwell C. Heat treating can increase hardness to approximately 60 Rockwell C. For specific applications, consult engineering. Besides cylinder parts, Pro-Coat may be applied to valve bodies, solenoid housings, fittings and most any item that appears in this catalog. Pro-Coat is available on all series, bore, stroke and action combinations. See Standard Specifications pages of desired bore and action for complete dimensional details. There are no dimensional changes from standard. STROKE COLLAR on Piston Rod in /8" increments. ) Start with the next longest stroke. 2) Select the amount the stroke is to be shortened. 3) Specify the corresponding SUFFIX designation. /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 For those "in-between" strokes, a STROKE COLLAR is incorporated on the piston rod. The collar fits tightly on the piston rod so that it cannot float as the piston is stroked. Tolerance on the stroke is ± /64". For tighter tolerances on the stroke or final rod position, consult Engineering. Available on all Series, all Bores, all s, s; -X, -XDR, -OP. Also all series, Bores 3/4" (7) and larger, all s, s; -XK, -XDRK. Also all Series, Bores /2" (5) & 3/4" (7), s; -O, -ODR. SEE Standard Specifications pages of desired Bore & for complete dimensional details. Cap End Rod Stick-out of Double Rod Units increases by amount stroke is shortened. Collar 2-3-08.0
Pancake Cylinders SUFFIX OPTIONS MODEL NUMBER SUFFIX ADJUSTABLE EXTEND STROKE For strokes through 4". -AS Full stroke adjustment is standard. NOTE! Use caution when mounting to avoid creating pinch poiunts. C-22-X-AS Original & "T" Series 8 Bores, /2" 4" Option Information SUFFIX OPTIONS Dial-A- provides a rugged and precision adjustment of the extend stroke of the cylinder. The stop tube, adjustment nut with skirt & minimum clearances combine to eliminate pinch points, thus providing operator safety. Note! Use caution when mounting to avoid creating pinch points with other parts of your machine design. The stop tube is blue anodized aluminum, the adjustment nut is blackened steel with a black anodized aluminum skirt, and the stop flange is red anodized aluminum; all for corrosion resistance and appearance. The adjustment nut, steel for long life, includes a lock screw with a plastic plug so that the adjustment nut can be locked in place without damaging the threads. The stop flange is mounted on the end of the adjustment rod so that the nut cannot come off. The fine pitch threads on the adjustment rod and nut provide precision adjustment. Bores -/8" (2) and -5/8" (22) have a /2-20 thread giving.050" adjustment per revolution & Bores 2" (32) & larger have a 3/4-6 thread giving.063" adjustment per revolution. The -AS designation provides full stroke adjustment. Available on Original Series, Bores /8" (2) & larger, all s, s; -X, -XK, -O. SEE Option Specifications pages of desired Bore and for complete dimensional details. Stop Tube Adjustment Nut Skirt Adjustment Nut with Fine Pitch Thread Stop Flange Adjustment Rod Adjustment settings are simplified by convenient scale markings applied to nut skirt and stop tube. Plastic Plug Lock Screw Contact Surfaces Totally Enclosed /2" Min. Clearance when Fully d ADJUSTABLE RETRACT STROKE Any stroke with up to and including " adjustment.....-rs Any stroke with over " adjustment, specify adjustment length after the -RS Example: 2" adjustment....-rs2 D-22-X-RS An adjusting screw with a thread sealing locknut mounted in a thick rear cover provides a simple yet rugged and precision adjustment of the cylinder stroke in the retract direction. The fine thread of the adjusting screw provides precision adjustment. Bores /2" (5), 3/4" (7), have a 5/6-24 thread giving.042" adjustment per revolution. Bore -/8" (2) has a 3/8-24 thread giving.042" adjustment per revolution. Bores -5/8" (22) and larger have a /2-20 thread giving.050" adjustment per revolution. The RS designation provides full stroke adjustment of any cylinder with " stroke or less, and " of stroke adjustment on all longer strokes. When longer adjustments are required, on longer cylinders, add the desired adjustment to the -RS designation (/2" increments please). Example:-RS2 will provide 2" of adjustment on any cylinder with 2" or more of stroke. Available on all series, all bores, all strokes, actions -X, -XK, -O, -OP. See Option Specifications pages of desired bore and action for complete dimensional details.. 4-23-04
SUFFIX OPTIONS MODEL NUMBER SUFFIX SOUND LIMITERS Rod End Only Cap End Only Both Rod and Cap Ends Temperature Range: 25 to +220 F -LF -LR -LFR Sound Limiting O'Ring Cushion Original & "T" Series 8 Bores, /2" 4" Option Information SUFFIX OPTIONS For applications where you need a small amount of cushion at the end of the cylinder stroke to take out the metallic slap of piston head on piston stop. This is accomplished by placing an O'Ring on the piston, and/or in the rear cover so that initial contact is with the elastomer and not metal-to-metal. The Fabco-Air design assures sufficient compression of the seals to allow full stroke. Because of the temperature limitations of the adhesives involved, sound limiters are available in cylinders with internally lubricated Buna-N O'Rings only. Available on all series, all bores, all strokes, actions -X, -O (Cap end only, -LR), -OP, -XDR, XDRK, -ODR (Cap end only -LR). See Standard Specifications pages of desired bore and action for complete dimensional details. There are no dimensional changes from standard. RUBBER BUMPERS Rod End Only Cap End Only Both Rod and Cap Ends Temperature Range: 25 to +220 F -BF -BR -BFR Rubber Standard rubber mass provided will compress and give full stroke at 60-80 psi. Mass can be adjusted to meet your specific pressure and/or dynamic load requirements A rubber doughnut is bonded to the cylinder head to act as the piston stop and absorb the impact of the piston. This reduces noise and absorbs energy, thus reducing destruction of the cylinder and tooling due to pounding. The amount of rubber that extends beyond the normal piston stop is designed to compress and allow full stroke of the cylinder at 60 to 80 psi. If your application uses lower pressure or has high energy, consult engineering with application details so that rubber mass can be adjusted to meet your specific requirements. On applications such as punching, shearing, etc., where high forces are built up and then very quickly released, the proper method of CATCH- ING this load is to adjust the position of the cylinder and tooling so at the point of breakthrough the piston is very close to or touching the bumper. This reduces the dynamic load that the piston and bumper are required to absorb. It is highly recommended that shock absorbers be considered and built into the tooling to assist in absorbing the force and dynamic loads generated in such applications. Because of the temperature limitations of the adhesives involved (-25 to + 220 F) Rubber Bumpers are available in cylinders with standard internally lubricated Buna-N seals only. Use to reduce noise and absorb impact. Note! The springs in single acting models are designed to return only the piston and rod assembly and will not significantly compress the rubber bumpers. Available on all series, all bores, all strokes, actions -X, -XK, -O (Cap end only, -BR), -OP (Rod end only, -BF), -XDR, XDRK, -ODR (Cap end only -BR). See Standard Specifications pages of desired bore and action for complete dimensional details. There are no dimensional changes from standard. 4-23-04.2
Pancake Cylinders SUFFIX OPTIONS MODEL NUMBER SUFFIX CLEVIS (Pivot) MOUNT Ports in Line with Slot Ports to Slot C-22-X-PM with RC-38 -PM -SM Original & "T" Series 8 Bores, /2" 4" Option Information SUFFIX OPTIONS CLEVIS mount provides a pivot point attachment to allow pivotal motion of the cylinder as the piston rod extends or retracts. The pivot is bushed with an oil filled powdered metal bushing. The pivot pin (46 stainless steel) and clips are included as standard. On bores -5/8" (22), 2-/2" (52), 3" (72) and 4" (22), the Clevis Mount can be rotated to provide either -PM or -SM option. To further assist in the mounting, rod clevises and eye brackets are available accessories. In many applications requiring pivotal mounting, the cylinder is mounted with its centerline horizontal. Due to the weight of the cylinder and its attachments, this can result in some off center loading, and possibly binding of the piston and rod, causing accelerated wear. For such applications the T Series cylinders are recommended. Available on all series, all bores, all strokes, actions: -X, -XK, -O, -OP. See Options Specifications pages of desired bore and action for complete dimensional details of cylinders, rod clevises and eye brackets. Eye (Pivot) MOUNT Ports in Line with Tang Ports to Tang C-22-X-EPM -EPM -ESM Eye mount provides a pivot point attachment to allow pivotal motion of the cylinder as the piston rod extends or retracts. The pivot is bushed with an oil filled powdered metal bushing. On bore -5/8" (22) the Eye Mount can be rotated to provide either -EPM or -ESM option. To further assist in the mounting, rod clevises and clevis brackets are available. In many applications requiring pivotal mounting, the cylinder is mounted with its centerline horizontal. Due to the weight of the cylinder and its attachments, this can result in some off center loading, and possibly binding of the piston and rod, causing accelerated wear. For such applications the T Series cylinders are recommended. Available on all series, bores:/2" (5), 3/4" (7), -/8" (2), -5/8" (22) and 2" (32), all strokes, actions: -X, -XK, -O, -OP. See Option Specifications pages of desired bore and action for complete dimensional details of cylinders, rod clevises and eye brackets. THREADED NOSE MOUNT -F C-22-X-F THREADED NOSE with pilot diameter provides convenient, rigid and precision mounting. A hex mounting nut is included as standard and is also available separately. On bores -/8" (2) and -5/8 (22) a urethane rod wiper is included, as standard, to exclude dirt from the rod bushing and seal. Available on all series, bores:/2" (5), 3/4" (7), -/8" (2), -5/8" (22), all strokes, all actions. See Option Specifications pages of desired bore and action for complete dimensional details of cylinder and mounting nuts..3 4-23-04
Original & "T" Series 8 Bores, /2" 4" Option Information Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) DT Mount /2" P'Cake 3/8/98 Order Sensors Separately Keyway slot for /2" bore Pancakes. Wire is in-line with slot. A single slot on longer stroke models has room to accommodate multiple sensors. Shorter stroke Pancake Cylinders are furnished with two dovetail mounting slots when Suffix Option "E" is specified. /4" 60 Dovetail for 3/4" bore Pancake s & up. /2" (5) Bore 3/4" (7) Bore /8" (2) Bore 5/8" (22) Bore Wire outlet is in-line with sensor mounting slot #2 60 60 #.09" Max #2 65 65 #.4" Ref. to 60 wire outlet; Zero stick-out of sensor body #2 40 40 # #2 45 45 # Sensors available for D & TD strokes and longer. s DJ & TD TJ have 2 mounting slots; others have. s D & TD are ported on opposite sides. Sensors available for D & TD strokes and longer. D J & TD TJ have 2 mounting slots; others have. s D & TD are ported on opposite sides. Sensors available for D & TD strokes and longer. D F & TD TF have 2 mounting slots; others have. s D & TD are ported on opposite sides. Sensors available for A & TB strokes and longer. A D & TB TD have 2 mounting slots; others have. s A is ported on opposite sides. 2" (32) Bore 72 2 /2" (52) Bore 45 3" (72) Bore 45 4" (22) Bore 45 #2 # #2 35 35 # 30 #2 30 # #2 30 30 # Sensors available for AA & TA strokes and longer. AA D & TA TD have 2 mounting slots; others have. s AA A & TA are ported on opposite sides. Sensors available for AA & TA strokes and longer. AA C & TA TC have 2 mounting slots; others have. AA is ported on opposite sides. Sensors available for AA & TA strokes and longer. AA C & TA TC have 2 mounting slots; others have. AA is ported on opposite sides. Sensors available for AB strokes and longer. AB A & TAA TA have 2 mounting slots; others have. Temperature Range: 20 to + 80 C ( 4 to + 76 F) Female Cordsets for Quick Disconnect Length Meter 2 Meters 5 Meters Part No. CFC-M CFC-2M CFC-5M Low Profile, Solid State, Magnetic Piston Position Sensors Encased in plastic housing, dovetail style sensors are corrosion resistant. 60 wire outlet allows close mounting. Profile shown here is typical for all but /2" bore Pancake s. 4--08 Ordering Guide Dovetail Style Magnetic Sensors for Pancake Cylinders Cylinder Model /2" Bore Pancake /2" Bore Pancake All other Pancakes All other Pancakes Sensor Type Electronic Electronic Electronic Electronic Prewired 9 ft. Part No. 9B49-000-03 9B49-000-032 949-000-03 949-000-032 Quick Disconnect Part No.* 9B49-000-33 9B49-000-332 949-000-33 949-000-332 Note*: /2" bore quick disconnect style supplied with 2" pigtail. All other bores supplied with 6" pigtail. Order female cordsets separately. LED Yes Yes Yes Yes Electrical Characteristics Sourcing, PNP, 6-24 VDC, 0.20 Amp Max current,.0 Voltage Drop Sinking, NPN, 6-24 VDC, 0.20 Amp Max current,.0 Voltage Drop Sourcing, PNP, 6-24 VDC, 0.20 Amp Max current, 0.5 Voltage Drop Sinking, NPN, 6-24 VDC, 0.20 Amp Max current, 0.5 Voltage Drop.4
Custom Options & Specials Specials Let us help you! Our engineering and special products departments are willing and able to assist you with your design. FABCO-AIR will produce cylinders and valves to meet your specific application requirements. In quantities of one and up. We have been doing it for almost 40 years. Many of our specials have become custom options; many have become standard catalog options. Custom Options are modifications that we produce on a routine basis, but they have too many combinations of features for practical listing in this catalog. Following are just a few of the more common of these custom options: Custom rod extensions Custom rod end configurations Pilot diameters on mounting faces Piece double rod, piston & rod assembly with or without a hole through Rod wipers, urethane or metallic Thick covers with ports Covers with manifolding Other materials Other lubricants s other than listed with special length bodies and rods Mounting styles & dimensions to specifications Back-to-Back cylinders for 3 or 4 positions Multiple position cylinders Tandem type for 3 or more positions Air Springs Constant Low Pressure Reg. Small regulator supplies constant pressure & controls spring force. Connection to Rod End Port results in a spring retracted type cylinder Connection to Cap End Port results in a spring extended type cylinder.5 An air spring allows the use of any standard double acting cylinder as a single acting spring return (push or pull) type. To accomplish this simply connect a constant regulated pressure (must be a relieving regulator) to the proper port of the double acting cylinder. This system gives you a variable spring load (by adjusting the pressure) that is consistent over the full stroke and life of the cylinder and will not break as helical compression springs often do. For space and cost savings, one regulator can serve several cylinders on the same machine. 2-4-08
Accessories Flow Controls Port Mounted, Swivel: Brass or Molded Body Mounts directly to Cylinder,Valve or Manifold. Brass Body Style (above) Male Sizes: #0-32, /8 NPT, /4 NPT Female NPT or Instant Tube Connections: #0-32, /8 NPT, /4 NPT, 5/32" T, /4" T, 3/8" T See page 2.3 & 2.4 for details. Molded Body Style (left) Male Sizes: #0-32, /8 NPT, /4 NPT, 3/8 NPT Instant Tube Connections: 5/32" T, /4" T, 3/8" T See page 2.3 for details. Position Sensors Dovetail Style, Low Profile, Solid State Electronic Sensor dovetail slides into a mating slot on the cylinder body, is positioned as desired, and locked in place with a set screw. See page.4 for Specifications Bolts Pancake Cylinder Mounting Bolts Fabco-Air has in stock socket head cap screws to mount all standard Pancake cylinders, all bores, all strokes. Also consider for Square and other products. SIZE LENGTH (Inches) /2 3/4 -/4 -/2-3/4 2 2-/4 2-/2 2-3/4 3 3-/2 4 4-/2 5 6 #6-32 #8-32 #0-32 /4-20 Wrench Flat Wrench Part Number WFW- 0.09" Thick, heat treated and plated steel wrench for holding the piston rod of Pancake cylinders while tightening or loosening rod end tooling or attachments. Also consider for Square and other products. 4-22-04.6
/2" (5) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired TE 5 X Suffix Options MR Metric M See pages.7,.9 &.22 Bore Code /2" 5 2.7mm 5 Standard s Original Series X O XDR ODR OP /6 A A A /8 B B B /4 C C C 3/8 D D D /2 E E E 5/8 F F 3/4 G G H H /4 I I /2 J J 2 K K 3 L 4 M T Series Includes PTFE piston bearing X O OP /8 TC TC TC /4 TD TD TD 3/8 TE TE TE /2 TF TF 5/8 TG TG TH TH /4 TI TI /2 TJ TJ 2 TK TK 3 TL 4 TM Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E Single rod Double acting -X Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.8 &.2 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 5 for /2" bore. Seven Other Bore Sizes are Available Bore Bore Code See page 3 / 4 "---------------- 7------------------.23 / 8 "------------2----------------.29 5 / 8 "------------22----------------.35 2"----------------32----------------.4 2 / 2 "------------52----------------.47 3"----------------72----------------.53 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES E-5-X Original Series, /2" stroke - /2" Bore - Single Rod, Double Acting TE-5-X-MR T Series, 3/8" - /2" Bore - Single Rod, Double Acting - Male Rod Thread Suffix Options Male rod thread: Single rod Double rod, rod end Double rod, cap end Double rod, both ends -MR -MR -MR -MR2 Viton seals -V Quad seals -Q External nonrotating guide -K Hex rod nonrotating, single acting models to 2" stroke only -NR Hole thru double rod shaft : / 6 " hole 50 psi max -06 Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot Ports to slot -PM -SM Eye mount: Ports in-line with tang -EPM Ports to tang -ESM Threaded nose mount: Single rod -F Double rod, rod end -F Double rod, cap end -F Double rod, both ends -F2 Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4 length determines number of mounting slots. See page.4,.20,.2. See pages.7.5 for general option information and pages.9,.20 &.22 for option specifications of /2" bore models. A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com.7 6-3-02
/2" (5) Bore Single Rod Standard Specifications X Double Acting Note : s H M & TH TM have two #6-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.20 Pull area =.5 Seal Kits for Series: Original = 5-SK "T" = 5-SKG 3/6 x. Wrench Flat B.3 K.3 8-32 x E.88 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS H M & TH TM. See Note.25 Rod Dia. Y Z.3 0-32 Ports with.38 Dia. Spotface s A D & TC TD are ported on Opposite Sides For Single Rod, Double Acting, Nonrotating See Option -K on page.20 Original Series "T" Series, Inch /6 /8 /4 3/8 /2 5/8 3/4 /4 /2 2 3 4 /8 /4 3/8 /2 5/8 /4 /2 2 3 4, Letter A B C D E F G H I J K L M TC TD TE TF TG TH TI TJ TK TL TM X Double Acting X Double Acting B.83.83.96.08.2.36.49.83 2.08 2.33 2.96 3.96 4.96.96.08.2.36.49.83 2.08 2.33 2.96 3.96 4.96 E.25.25.25.38.38.38.38.38.38.38.38.38.38.25.38.38.38.38.38.38.38.38.38.38 K.56.56.69.8.94.09.22 Note Note Note Note Note Note.69.8.94.09.22 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.55.55.55.46.46.46.46.46.46.46.46.55.55.55 Z.52.52.65.77.89.05.8.52.77 2.02 2.65 3.65 4.65.65.77.89.05.8.52.77 2.02 2.65 3.65 4.65 Weight, lb..08.08.08.09..2.3.6.9.2.27.36.46.08.09..2.3.6.9.2.27.36.46 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.83.96.08.36.49.83 2.33 2.96 2.96 3.96 3.96 NA* NA*.08.36.49.83 2.33 2.96 2.96 3.96 3.96 NA* NA* E3.25.25.38.38.38.38.38.38.38.38.38 " ".38.38.38.38.38.38.38.38.38 " " K3.56.69.8.09.22 Note Note Note Note Note Note " ".8.09.22 Note Note Note Note Note Note " " Y3.46.46.46.46.46.46.46.55.55.55.55 " ".46.46.46.46.46.55.55.55.55 " " Z3.52.65.77.05.8.52 2.02 2.65 2.65 3.65 3.65 " ".77.05.8.52 2.02 2.65 2.65 3.65 3.65 " " Weight,. lb..08.09.0.2.3.6.22.28.28.37.37 " ".08.09.0.2.3.6.22.28.28 " " Preload, lb. 2.0 2.0.9.2.7.9.2.0.7.3.3 " " 2.8 2.0.2.9.9.0.7.3.3 " " End of, lb. 3.2 3.2 3.2 3.2 3.2 3.5 3.2 3.5 5.7 5.3 6.7 " " 3.2 3.2 3.2 3.5 3.5 3.5 5.7 5.3 5.3 " " OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4.95.6.39.80 2.05 NA* NA* NA* NA* NA* NA* NA* NA*.26.67.92 NA* NA* NA* NA* NA* NA* NA* NA* E4.25.25.25.38.38 " " " " " " " ".25.25.38 " " " " " " " " K4.63.77.88.6.29 " " " " " " " ".88.6.29 " " " " " " " " Y4.52.58.7.83.96 " " " " " " " ".58.70.83 " " " " " " " " Z4.64.85.08.49.74 " " " " " " " ".95.36.6 " " " " " " " " Weight, lb..08.09.2.3.4 " " " " " " " ".08.09.2 " " " " " " " " Preload, lb..7.7.7.2.7 " " " " " " " ".7.7.7 " " " " " " " " End of, lb. 3.0 3.0 3.0 3.2 3.2 " " " " " " " " 3.0 3.0 3.0 " " " " " " " " O Single Acting Spring Retracted Note : s F K & TF TK have two #6-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.20 See chart for Spring Forces: Preload and End of. Seal Kits for Series: Original = 5-SK "T" = 5-SKG 3/6 x. Wrench Flat B3.3 K3.3 8-32 x E3.88 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS F K & TF TK. See Note.25 Rod Dia. Y3 Z3.3 0-32 Ports with.38 Dia. Spotface s A C & TC are ported on Opposite Sides OP Single Acting 3/6 x. Spring Extended Wrench Flat See page.6 for Mounting Bolts. Pull area =.5 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 5-SK "T" = 5-SKG B4.3 + K4.3 8-32 x E4.88 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS.25 Rod Dia. Y4 Z4.9 0-32 Ports with.38 Dia. Spotface s A C & TC are ported on Opposite Sides 4-22-04 NA* = Not Available.8
/2" (5) Bore Also See Page.8 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 2.7mm Bore Available on Original and T Series with s: -X, -O, -OP Also see Option Information on page.7. Original Series mm.6 3.2 6.4 9.5 2.7 5.9 9. 25.4 3.8 38. 50.8 76.2 0.6 Letter A B C D E F G H I J K L M T Series mm 3.2 6.4 9.5 2.7 5.9 25.4 3.8 38. 50.8 76.2 0.6 Letter TC TD TE TF TG TH TI TJ TK TL TM Mounting Holes 3.6mm Diameter Thru 5.9mm C'Bore x 3.6mm Dp. 2 Places for M3 SHCS Except s H-M & TH - TM which have two M4 x 2.0mm Dp. Tapped Mounting Holes on each end. Thread Pitches M3 = 0.5mm M4 = 0.7mm M5 = 0.8mm M4 x 2.7 Conversion Factor Inches x 25.4 = mm 22.2mm Bolt Circle Standard Female Rod Thread M4. Male Rod Thread Option -MR shown. M5 Ports with 9.5mm Dia. Spotface The Suffix Options charted on the right are available on Original & T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.8. Also see Option Information on pages.7 thru.5. V Q N C C7 BF BR BFR -X -O NA NA -OP NA NA Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -O, -OP Also see Option Information on page.3..44 + B See Page.8.25.34 Note.4 Note : Hole Diameter =.25 Pin Diameter =.250 Pin (46 Stainless Steel) and Clips are included -PM Port Location IN LINE with Slot -SM Port Location to Slot Suffix Options -EPM & -ESM Eye Mount Available on Original and T Series with s: -X, -O, -OP Also see Option Information on page.3..44 + B See Page.8.4.25.34.25 -EPM Port Location IN LINE with Tang.63 -ESM Port Location to Tang.25.63.83.23 Oil filled bushings Oil filled bushing EM-04 Eye Bracket Kit Mates with Clevis Mount above. Order separately..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.88.25.88.56.25.87.23 Hole.25 Oil filled bushing.6 is standard.4 PM-04 Clevis Bracket Kit Mates with Eye Mount above. Order separately..27 Dia. 4 Places on Square Pattern for Flat Head Screws. Four /4-20 x 3/4" FH(#2)M Screws are included..63.88.25.83.63.25.30.56.8.6 Material: Zinc Die Casting.4 Hole.25 Pin.250 Pin (46 Stainless Steel) & Clips included. Oil Filled Bushings are Standard. RC-6 Rod Clevis and Pin Threaded Stud mates with Female Rod thread in Pancake Cylinders. Slot & Pin Mate with EM-02 Eye Bracket shown on the right. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.9.00.75.70.38.33.50 Pin Diameter.875 8-32 x.25 Optional Metric #MRC-6 M4 x 6.3mm EM-02 Eye Bracket Kit Mates RC-6 Rod Clevis shown on the left..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.88.25.88.56.25.87.8 Hole.885 Oil filled bushing.6 is standard.36.9-4-08
/2" (5) Bore Also See Page.8 Option Specifications Suffix Option -RS Adjustable Retract Available on Original and "T" Series with s -X, -O, -OP. Also see Option Information on page..7.06 + B -OP only use B4 as shown on page.8. No additional length is required Suffix Option -NR Available on Original and "T" Series with -O. Also see Option Information on page.8 Suffix Option -MR Available on Original and "T" Series with s -X, -O, -OP. Also see Option Information on page.8 /2 Hex Nut Adjusting Screw.042 Adjustment Per Revolution s " & Shorter =.38 Max + s " & Longer =.38 + Adjustment Standard Adjustment is ". Nonrotating, Single Acting.25 Hex Stainless Steel Piston Rod Male Rod Thread 8-32 x.50 Suffix Option -F Threaded Nose Mount Available on Original and "T" Series with s -X, -O, -OP. Also see Option Information on page.3.3.38 Pilot Dia. =.495.49 Pilot Length =.06.38 + B (for A J s);.29 + B (for K, L & M s).63.50 Dia..38.56.3.3.75.50.09.20 Dia..3.75 Part No: BRK-20 /2-20.50 Dia..20 Dia..56.3.75.50 /2-20 Thread Accessory Plated steel nose mounting brackets Must be ordered separately Angled Part Number BRK-20 Flat Part Number BRK-202 Ref..56.88 6.50.25.38.3 A J.48 + B K M.38 + B Standard Rod End Brass Clamp Nut Part No. MC-500-95 is included. Material: Brass.72.09.80.99 Suffix Option -K Nonrotating, Double Acting Available on Original and "T" Series with -X, -O, -OP..25 Ground Tool Steel Pin is Guided by Precision Hole in End Cap Clearance in Body for Guide Pin 5/8.25 Rotational Tolerance with Piston Rod Fully Retracted (Clamp near Body) is ±. Cylinder is not intended to carry any rotational load. Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by Magnetic Piston Option Sensors Must be Ordered Separately See Sensor Models Available page.4 Note: Alloy steel mounting bolts may effect sensing. Stainless steel or other nonmagnetic bolts are recommended. Profile of Sensor & Keyway Slot. Wire is in line with slot. Sensors available for D & TD strokes and longer. s D & TD are ported on opposite sides. Wire outlet is in-line with sensor mounting slot #2 /2" (5) Bore 60 60 #.09" Max Sensor Slots at Positions # and #2 Sensor Slot at Position # only Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series X 3/8-------------------- D /2-------------------- E 5/8-------------------- F 3/4-------------------- G ----------------------- H /4------------------- I /2-------------------J 2----------------------- K 3------------------------L 4----------------------- M Available on T Series X /4------------- TD 3/8------------- TE /2------------- TF 5/8-------------TG ---------------- TH /4------------TI /2----------- TJ 2---------------- TK 3---------------- TL 4----------------TM 4--08.20
/2" (5) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting Note : s H M have two #6-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.5 Seal Kit = 5-SK, Inches /6 /8 /4 3/8 /2 5/8 3/4 -/4 -/2 2 3 4, Letter A B C D E F G H I J K L M B.00.00.3.25.38.50.63.88 2.3 2.38 2.88 3.88 4.88 E.25.25.25.38.38.38.38.38.38.38.38.38.38 K.73.73.86.98..23.36 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.46.46.46 Z.67.67.80.92.05.7.30.55.80 2.05 2.55 3.55 4.55 Weight, lb..09.0..2.3.4.6.8.2.24.3.4.52 3/6 x. Wrench Flat B.3 K.3 +.3 Y 8-32 x E.88 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp both ends for 2, #6 SHCS H M See Note.25 Rod Dia. Z.4 0-32 Ports with.38 Dia. Spotface s A C are ported on Opposite Sides ODR Original Series Double Rod, Single Acting, Spring Retracted Note : s F K have two #6-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.5 Seal Kit = 5-SK, Inches /6 /8 /4 3/8 /2 5/8 3/4 /4 /2 2, Letter A B C D E F G H I J K B.00.3.25.55.67.88 2.38 2.88 2.88 3.88 3.88 E.25.25.25.38.38.38.38.38.38.38.38 K.73.86.98.28.40 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.46 Z.67.80.92.22.34.55 2.05 2.55 2.55 3.55 3.55 Weight, lb..09.0.3.5.6.9.24.30.30.40.40 Spring Return Forces, lb. Preload 2.0 2.0 0.9.2 0.7.9.2.0.7.3.3 End of 3.2 3.2 3.2 3.2 3.2 3.5 3.2 3.5 5.9 5.3 6.7 3/6 x. Wrench Flat B.3 K.3 +.3 Y 8-32 x E.88 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp both ends for 2, #6 SHCS H M See Note.25 Rod Dia. Z.4 0-32 Ports with.38 Dia. Spotface s A C are ported on Opposite Sides Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by Magnetic Piston Option Sensors Must be Ordered Separately See Sensor Models Available page.4 Note: Alloy steel mounting bolts may effect sensing. Stainless steel or other non-magnetic bolts are recommended. Profile of Sensor & Keyway Slot. Wire is in line with slot. Sensors available for D strokes and longer. Wire outlet is in-line with sensor mounting slot #2 /2" (5) Bore 60 60 #.09" Max Sensor Slots at Positions # and #2 Sensor Slot at Position # only Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series XDR 3/8-------------------- D /2-------------------- E 5/8-------------------- F 3/4-------------------- G ----------------------- H /4------------------- I /2-------------------J 2----------------------- K 3------------------------L 4----------------------- M.2 2-5-08
/2" (5) Bore Also See Page.2 Prefix Option -M Metric Cylinder & Rod Thread, 2.7mm Bore Available on Original Series with s: -XDR, -ODR Also see Option Information on page.7. mm.6 3.2 6.4 9.5 2.7 5.9 9. 25.4 3.8 38. 50.8 76.2 0.6 Letter A B C D E F G H I J K L M Option Specifications Mounting Holes 3.6mm Diameter Thru 5.9mm C'Bore x 3.6mm Dp. 2 Places for M3 SHCS Except s H-M which have two M4 x 2.0mm Dp. Tapped Mounting Holes on each end. Thread Pitches M3 = 0.5mm M4 = 0.7mm M5 = 0.8mm M4 x 2.7 Conversion Factor Inches x 25.4 = mm 22.2mm Bolt Circle Standard Female Rod Thread M4. Male Rod Thread Option -MR shown. M5 Ports with 9.5mm Dia. Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.2. Also see Option Information on pages.7 thru.5. V Q N C C7 BF BR BFR 06 -XDR -ODR NA NA Suffix Option -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -ODR. For Rod End only use MR For Cap End only use MR For Both Ends use MR2 Also see Option Information on Page.8 8-32 x.50 Suffix Option -NR Nonrotating, Single Acting Available on Original Series with -ODR Also see Option Information on page.8..25 Hex Stainless Steel Piston Rod Suffix Option -F, -F, -F2 Threaded Nose Mount (See info page.3) Available on Original Series with s -XDR, -ODR. For Rod End only use -F /2-20 Pilot Dia. =.495 Pilot Length =.06 For Cap End only use -F.49 For Both Ends use -F2 /2-20 Nut. Part No. MC-500-95 is included. Material: Brass.72 5/8.25.3.3.38.38+ B.3 + Accessory Nose Mounting Brackets Order separately Material Plated Steel.63.50 Dia..38.56.3.75.50.09.20 Dia..3.75 Part No: BRK-20.50 Dia..20 Dia..56.3.75.50.09.80.99.25 Part No: BRK-202 Suffix Option -K Nonrotating, Double Acting Available on Original Series with s: -XDR, -ODR. Rotational Tolerance with Piston Rod Fully Retracted (Clamp near Body) is ±. Cylinder is not intended to carry any rotational load. Ref..56.88 6.50.25.38.3 A J.48 + B K M.38 + B Standard Rod End Brass Clamp Ground Tool Steel Pin is Guided by Precision Hole in End Cap Clearance in Body for Guide Pin.3 + 4-22-04.22
3/4" (7) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired TE 7 X Suffix Options MR Metric M See pages.7,.25,.28 Bore Code 3/4" 7 9.mm 7.23 Standard s Note : For action XK strokes A G are decreased by /8" from those shown (Original Series only). Note 2: For action XDRK strokes A M are decreased by /8" from those shown (Original Series only). Original Series X XK O XDR XDRK 2 ODR OP /6 A A A /8 B B B /4 C C C 3/8 D D D /2 E E E 5/8 F F 3/4 G G H H /4 I I /2 J J 2 K K 3 L 4 M T Series Includes PTFE piston bearing X, XK O OP /8 TC TC TC /4 TD TD TD 3/8 TE TE TE /2 TF TF 5/8 TG TG TH TH /4 TI TI /2 TJ TJ 2 TK TK 3 TL 4 TM Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E Single rod Double acting -X Double acting, Nonrotating -XK 50 psi max Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Double acting, Nonrotating -XDRK 50 psi max Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.24 &.27 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 7 for 3/4" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 / 8 "------------2----------------.29 5 / 8 "------------22----------------.35 2"----------------32----------------.4 2 / 2 "------------52----------------.47 3"----------------72----------------.53 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES E-7-X Original Series, /2" stroke - 3/4" Bore - Single Rod, Double Acting TE-7-X-MR T Series, 3/8" - 3/4" Bore - Single Rod, Double Acting - Male Rod Thread A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com Suffix Options Male rod thread: Single rod Double rod, rod end Double rod, cap end Double rod, both ends Viton seals -V Quad seals -Q -MR -MR -MR -MR2 External guide, nonrotating for load guiding (See page.65) -G Hex rod nonrotating, single acting models to 2" stroke only -NR Hole thru double rod shaft : / 6 " hole -06 50 psi max Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot -PM Ports to slot -SM Eye mount: Ports in-line with tang -EPM Ports to tang -ESM Threaded nose mount: Single rod -F Double rod, rod end -F Double rod, cap end -F Double rod, both ends -F2 Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.26, or.28. See pages.7.5 for general option information and pages.25,.26 &.28 for option specifications of 3/4" bore models. 6-3-02
3/4" (7) Bore Single Rod Standard Specifications X Double Acting Note : s H M & TH TM have two #8-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.44 Pull area =.36 Seal Kits for Series: Original = 7-SK "T" = 7-SKG /4 x. Wrench Flat B.3 K.50 0-32 x E.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS H M & TH TM. See Note.3 Rod Dia. Y Z.3 0-32 Ports with.38 Dia. Spotface s A D & TC TD are ported on Opposite Sides XK Double Acting Nonrotating Note : s H M & TH TM have two #8-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.42 Pull area =.34 Seal Kits for Series: Original = 7-SK-K "T" = 7-SKG-K /4 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.3 B2 K2.50 0-32 x E.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS H M & TH TM. See Note.3 Rod Dia. Y2 Z2.3 0-32 Ports with.38 Dia. Spotface s C D & TC TD are ported on Opposite Sides Original Series "T" Series, Inch /6 /8 /4 3/8 /2 5/8 3/4 /4 /2 2 3 4 /8 /4 3/8 /2 5/8 /4 /2 2 3 4, Letter A B C D E F G H I J K L M TC TD TE TF TG TH TI TJ TK TL TM X Double Acting X Double Acting B.83.83.96.08.2.36.49.83 2.08 2.33 2.96 3.96 4.96.96.08.2.36.49.83 2.08 2.33 2.96 3.96 4.96 E.25.25.25.38.38.38.38.38.38.38.38.38.38.25.38.38.38.38.38.38.38.38.38.38 K.56.56.69.8.94.09.22 Note Note Note Note Note Note.69.8.94.09.22 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.55.55.55.46.46.46.46.46.46.46.46.55.55.55 Z.52.52.65.77.89.05.8.52.77 2.02 2.65 3.65 4.65.65.77.89.05.8.52.77 2.02 2.65 3.65 4.65 Weight, lb..4.4.5.7.20.2.23.28.32.36.46.63.78.5.7.20.2.23.28.32.36.46.63.78 XK Double Acting, Nonrotating XK Double Acting, Nonrotating, Inch /8 /4 3/8 /2 5/8 /4 /2 2 3 4 B2.96.08.2.36.49.83 2.08 2.33 2.96 3.96 4.96, Letter C D E F G H I J K L M E2.25.38.38.38.38.38.38.38.38.38.38 Use s & Dimensions under K2.69.8.94.09.22 Note Note Note Note Note Note "T" Series XK Double Acting Y2.46.46.46.46.46.46.46.46.55.55.55 Z2.65.77.89.05.8.52.77 2.02 2.65 3.65 4.65 Weight, lb..5.8.2.22.24.29.33.37.48.65.8 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.83.96.08.36.49.83 2.33 2.96 2.96 3.96 3.96 NA* NA*.08.36.49.83 2.33 2.96 2.96 3.96 3.96 NA* NA* E3.25.25.38.38.38.38.38.38.38.38.38 " ".38.38.38.38.38.38.38.38.38 " " K3.56.69.8.09.22 Note Note Note Note Note Note " ".8.09.22 Note Note Note Note Note Note " " Y3.46.46.46.46.46.46.55.55.55.55.55 " ".46.46.46.46.46.55.55.55.55 " " Z3.52.65.77.05.8.52 2.02 2.65 2.65 3.65 3.65 " ".77.05.8.52 2.02 2.65 2.65 3.65 3.65 " " Weight,. lb..4.6.8.22.23.28.36.46.46.63.63 " ".8.22.23.28.28.46.46.63.63 " " Preload, lb. 2.0 2.7.5 2.5 2.0 2.5 2.5 2.2.5.3.3 " " 2.8.5 2.5 2.5 2.5.5.2.3.3 " " End of, lb. 3.0 4.5 4.5 4.7 4.7 4.8 4.8 4.9 5.0 5.3 6.7 " " 4.5 4.5 4.8 4.8 4.8 4.9 5.0 5.3 6.7 " " OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4.95.6.39.80 2.05 NA* NA* NA* NA* NA* NA* NA* NA*.26.67.92 NA* NA* NA* NA* NA* NA* NA* NA* E4.25.25.25.38.38 " " " " " " " ".25.25.38 " " " " " " " " K4.63.77.88.6.29 " " " " " " " ".88.6.29 " " " " " " " " Y4.52.58.7.83.96 " " " " " " " ".58.70.83 " " " " " " " " Z4.64.85.08.49.74 " " " " " " " ".95.36.6 " " " " " " " " Weight, lb..4.6.8.22.24 " " " " " " " ".8.22.24 " " " " " " " " Preload, lb. 2.0 2.7.5 2.5 2.0 " " " " " " " ".5 2.5 2.0 " " " " " " " " End of, lb. 3.0 4.5 4.5 4.7 4.7 " " " " " " " " 4.5 4.8 4.8 " " " " " " " " O Single Acting Spring Retracted Note : s F K & TF TK have two #8-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.44 See chart for Spring Forces: Preload and End of. Seal Kits for Series: Original = 7-SK "T" = 7-SKG /4 x. Wrench Flat B3.3 K3.50 0-32 x E3.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS F K & TF TK See Note.3 Rod Dia. Y3 Z3.3 0-32 Ports with.38 Dia. Spotface s A C & TC are ported on Opposite Sides OP Single Acting Spring Extended See page.6 for Mounting Bolts. Pull area =.36 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 7-SK "T" = 7-SKG /4 x. Wrench Flat B4.3 + K4.50 Y4 0-32 x E4.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp. for 2, #6SHCS.3 Rod Dia. Z4.9 0-32 Ports with.38 Dia. Spotface s A C & TC are ported on Opposite Sides 4-23-04 NA* = Not Available.24
3/4" (7) Bore Also See Page.24 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 9.mm Bore Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.7. Original Series mm.6 3.2 6.4 9.5 2.7 5.9 9. 25.4 3.8 38. 50.8 76.2 0.6 Letter A B C D E F G H I J K L M T Series mm 3.2 6.4 9.5 2.7 5.9 25.4 3.8 38. 50.8 76.2 0.6 Letter TC TD TE TF TG TH TI TJ TK TL TM Mounting Holes 4.3mm Diameter Thru 7.2mm C'Bore x 3.6mm Dp. 2 Places for M4 SHCS Except s H-M and TH-TM which have two M5 x. Dp. Tapped Mounting Holes on each end. Thread Pitches M4 = 0.7mm M5 = 0.8mm M5 x 2.7 Conversion Factor Inches x 25.4 = mm 30.2mm Bolt Circle Standard Female Rod Thread M5. Male Rod Thread Option -MR shown. M5 Ports with 9.5mm Dia. Spotface The Suffix Options charted on the right are available on Original & T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.24. Also see Option Information on pages.7 thru.5. V Q N C C7 BF BR BFR -X -XK -O NA NA -OP NA NA Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3..44 + B See Page.24.25.34 Note.4 Note : Hole Diameter =.25 Pin Diameter =.250 Pin (46 Stainless Steel) and Clips are included -PM Port Location IN LINE with Slot -SM Port Location to Slot Suffix Options -EPM & -ESM Eye Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3..44 + B See Page.24.4.25.34.25 -EPM Port Location IN LINE with Tang.63 -ESM Port Location to Tang.25.63.83.23 Oil filled bushings Oil filled bushing EM-04 Eye Bracket Kit Mates with Clevis Mount above. Order separately..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.88.25.23.3.88.6.25.56.87 Hole.25 Oil filled bushing is standard.4 PM-04 Clevis Bracket Kit Mates with Eye Mount above. Order separately..27 Dia. 4 Places on Square Pattern for Flat Head Screws. Four /4-20 x 3/4" FH(#2)M Screws are included..63.88.25.83.63.25.30.56.8.6 Material: Zinc Die Casting.4 Hole.25 Pin.250 Pin (46 Stainless Steel) & Clips included. Oil Filled Bushings are Standard. RC-9 Rod Clevis and Pin Threaded Stud mates with Female Rod thread in Pancake Cylinders. Slot & Pin Mate with EM-02 Eye Bracket shown on the right. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.9.00.75.70.38.33.50 Pin Diameter.875 0-32 x.25 Optional Metric #MRC-9 M5 x 6.3mm EM-02 Eye Bracket Kit Mates RC-9 Rod Clevis shown on the left..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.88.25.88.56.25.87.8 Hole.885 Oil filled bushing.6 is standard.36.25 6-6-05
3/4" (7) Bore Also See Page.24 Option Specifications Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK, -O, -OP. 0-32 x.50 Also see Option Information on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.. /2 Hex Nut Adjusting Screw Suffix Option -F Threaded Nose Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3..3.50 5/8-8 5/8-8 3/4 Hex.042 Adjustment Per Revolution.7 s " & Shorter =.38 Max. + s " & Longer =.38 + Adjustment.06 + B Standard Adjustment is " (-OP Only use B4 as shown on page.24. No additional length is required.) Suffix Option -NR Nonrotating, Single Acting Available on Original and T Series with -O Also see Option Information on page.8..38.38 + B (for A J s) (.29 + B for K, L, M s) Pilot Dia. =.620.65 Pilot Length =.06 Accessory Nose Mounting Brackets Order Separately. Material: Plated Steel Angled Part Number BRK-30.88.25 Part No. MC-700-95 Mounting Nut is included Material: Brass Flat Part Number BRK-302.69.2.44.25.63.20 Dia..63 2.25.75 Dia..25.00.63.25.2.63 Dia..20 Dia..3 Hex Stainless Steel Piston Rod.90.80.25.90.80 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by Magnetic Piston Option Note: Alloy steel mounting bolts may effect sensing. Stainless steel or other non-magnetic bolts are recommended. /4" 60 Dovetail Profile of Sensor & Mounting Slot. #2 3/4" (7) Bore Sensors available for D & TD strokes and longer. s D & TD are ported on opposite sides. 65 65 #.4" Ref. to 60 wire outlet; Zero stick-out of sensor body Sensor Slots at Positions # and #2 Sensor Slot at Position # only Sensors Must be Ordered Separately See Sensor Models Available page.4 Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series X, XK 3/8----------------- D /2------------------E 5/8------------------F 3/4----------------- G ------------------- H /4--------------- I /2---------------J 2--------------------K 3--------------------L 4------------------- M Available on T Series X, XK /4----------------TD 3/8----------------TE /2----------------TF 5/8--------------- TG ------------------TH /4------------- TI /2-------------TJ 2------------------TK 3------------------TL 4----------------- TM Note : For XK strokes D G are decreased by /8" for those shown for Original Series. There is no decrease in stroke for T Series. 4--08.26
3/4" (7) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting Note : s H M have two #8-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.36 Seal Kit = 7-SK /4 x. Wrench Flat.3.50 0-32 x E.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp both ends for 2, #6 SHCS H M See Note.3 Rod Dia., Inches /6 /8 /4 3/8 /2 5/8 3/4 -/4 -/2 2 3 4, Letter A B C D E F G H I J K L M B.00.00.3.25.38.50.63.88 2.3 2.38 2.88 3.88 4.88 E.25.25.25.38.38.38.38.38.38.38.38.38.38 K.73.73.86.98..23.36 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.46.46.46 Z.67.67.80.92.05.7.30.55.80 2.05 2.55 3.55 4.55 Weight, lb..6.6.9.22.23.26.28.32.36.4.49.69.86 Y Z B K.4.3 + 0-32 Ports with.38 Dia. Spotface s A C are ported on Opposite Sides XDRK Original Series Double Rod, Double Acting, Nonrotating Note : s H M have two #8-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.35 Seal Kit = 7-SK-K, Inches /8 /4 3/8 /2 5/8 7/8 /8 3/8 7/8 2 7/8 3 7/8, Letter C D E F G H I J K L M B.3.25.38.50.63.88 2.3 2.38 2.88 3.88 4.88 E.25.38.38.38.38.38.38.38.38.38.38 K.86.98..23.36 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.46 Z.80.92.05.7.30.55.80 2.05 2.55 3.55 4.55 Weight, lb..20.22.24.27.29.33.37.43.5.7.89 /4 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.3 B K.3 +.50 Y 0-32 x E.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp both ends for 2, #6 SHCS H M See Note.3 Rod Dia. Z.4 0-32 Port with.38 Dia. Spotface C is ported on Opposite Sides ODR Original Series Double Rod, Single Acting, Spring Retracted Note : s F K have two #8-32 x.44 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.36 Seal Kit = 7-SK, Inches /6 /8 /4 3/8 /2 5.8 3/4 /4 /2 2, Letter A B C D E F G H I J K B.00.3.25.55.67.88 2.38 2.88 2.88 3.88 3.88 E.25.25.25.38.38.38.38.38.38.38.38 K.73.86.98.28.40 Note Note Note Note Note Note Y.46.46.46.46.46.46.46.46.46.46.46 Z.67.80.92.22.34.55 2.05 2.55 2.55 3.55 3.55 Weight, lb..6.9.20.22.23.33.43.5.5.7.7 Spring Return Forces, lb. Preload 2.0 2.8.5 2.5 2.0 2.5 2.5 2.2.5.3.3 End of 3.0 4.5 4.5 4.8 4.8 4.8 4.8 4.9 5.0 5.3 6.7 /4 x. Wrench Flat.3 Rod Dia. B.3 K.3 +.50 Y 0-32 x E.9 Bolt Circle.4 Dia. Thru.23 C'Bore x.4 Dp both ends for 2, #6 SHCS H M See Note Z.4 0-32 Port with.38 Dia. Spotface s A C are ported on Opposite Sides.27 4-22-04
3/4" (7) Bore Also See Page.24 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 9.mm Bore Available on Original Series with s: -XDR, -XDRK, -ODR Also see Option Information on page.7. -XDR & -ODR -XDR mm.6 3.2 6.4 9.5 2.7 5.9 9. 25.4 3.8 3.8 50.8 76.2 0.6 Letter A B C D E F G H I J K L M -XDRK mm NA NA 3.2 6.3 9.5 2.7 5.9 22.2 28.6 34.9 47.6 73.0 98.4 Letter A B C D E F G H I J K L M Mounting Holes 4.3mm Diameter Thru 7.2mm C'Bore x 3.6mm Dp. 2 Places for M4 SHCS Except s H-M and TH-TM which have two M5 x. Dp. Tapped Mounting Holes on each end. Thread Pitches M4 = 0.7mm M5 = 0.8mm M5 x 2.7 Conversion Factor Inches x 25.4 = mm 30.2mm Bolt Circle Standard Female Rod Thread M5. Male Rod Thread Option -MR shown M5 Ports with 9.5mm Dia. Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.27. Also see Option Information on pages.7 thru.5. Suffix Option -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use MR 0-32 x.50 For Cap End only use MR For Both Ends use MR2 Also see Option Information on Page.8 V Q N C C7 BF BR BFR 06 -XDR -XDRK -ODR NA NA Suffix Option -NR Nonrotating, Single Acting Available on Original Series with s: -ODR Also see Option Information on page.8..3 Hex Stainless Steel Piston Rod Suffix Option -F, -F, -F2 Threaded Nose Mount Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use -F For Cap End only use -F For Both Ends use -F2 5/8-8 Also see Option Information on page.3 Nut Part No. MC-700-95 is included. Material: Brass.88 3/4 Hex.25.50.3 5/8-8 Pilot Dia. =.620 Pilot Length =.06.65.38.38+ B.3 + Accessory Nose Mounting Brackets Order Separately. Material Plated Steel BRK-30.69.2.44.25.63.20 Dia..63 2.25.75 Dia..25.00.90.80.25 BRK-302.63.25.90.80.2.63 Dia..20 Dia. Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by Magnetic Piston Option Note: Alloy steel mounting bolts may effect sensing. Stainless steel or other non-magnetic bolts are recommended. /4" 60 Dovetail Profile of Sensor & Mounting Slot. #2 Sensors available for D strokes and longer. 65 65 3/4" (7) Bore #.4" Ref. to 60 wire outlet; Zero stick-out of sensor body Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Sensors Must be Ordered Separately See Sensor Models Available page.4 Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series XDR, XDRK 2 3/8----------------- D /2------------------E 5/8------------------F 3/4----------------- G ------------------- H /4--------------- I /2---------------J 2--------------------K 3--------------------L 4------------------- M Note 2: For XDRK strokes D M are decreased by /8" for those shown for Original Series. 4--08.28
/8" (2) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired D 2 X Suffix Options MR Metric M See pages.7,.3 &.34 Bore Code /8" 2 28.5mm 2.29 Standard s Original Series X XK O XDR XDRK ODR OP /8 A A A 3/6 B B B /4 C C C /2 D* D D 3/4 X X X E E E /4 F F F /2 G G G 3/4 H H 2 I I 3 J 4 K T Series Includes PTFE piston bearing X XK O OP /6 TB TB TB /8 TC TC TC 3/8 TD* TD TD 5/8 TX TX TX 7/8 TE TE TE /8 TF TF TF 3/8 TG TG TG 5/8 TH TH 7/8 TI TI 2 7/8 TJ 3 7/8 TK Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E * Note Sensors not available: Single rod Double acting -X Double acting, Nonrotating Internal guide pins - 50 psi max -XK Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Double acting, Nonrotating Internal guide pins - 50 psi max -XDRK Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.30 &.33 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 2 for /8" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 3 / 4 "---------------- 7------------------.23 5 / 8 "------------22----------------.35 2"----------------32----------------.4 2 / 2 "------------52----------------.47 3"----------------72----------------.53 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES D-2-X Original Series, /2" stroke - /8" Bore - Single Rod, Double Acting TD-2-X-MR T Series, 3/8" - /8" Bore - Single Rod, Double Acting - Male Rod Thread D-2-XK, TD-2-XK, D-2-XDRK A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com Suffix Options Male rod thread: Single rod -MR Double rod, rod end -MR Double rod, cap end -MR Double rod, both ends -MR2 PTFE seals -T Viton seals -V Quad seals -Q External guide, nonrotating for load guiding (See page.65) -G Hydraulic: Standard cover -H Hole thru double rod shaft: / 8 " hole -3 Plus size: 5/32" hole -6 50 psi max Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Sound limiters: Rod end -LF Cap end -LR Both ends -LFR Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable extend stroke (Full stroke adjustment is standard) -AS Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot Ports to slot -PM -SM Eye mount: Ports in-line with tang Ports to tang -EPM -ESM Threaded nose mount: Single rod -F Double rod, rod end -F Double rod, cap end -F Double rod, both ends -F2 Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.32,.34 See pages.3.5 for general option information and pages.3,.32 &.34 for option specifications of /8" bore models. 6-22-02
-/8" (2) Bore Single Rod Standard Specifications X Double Acting Note : s J, K, TJ, & TK have two #0-32 x.50 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.99 Pull area =.80 Seal Kits for Series: Original = 2-SK "T" = 2-SKG 7/6 x. Wrench Flat B.4 K.99 5/6-24 x E.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS J, K, TJ & TK See Note.50 Rod Dia. Y Z.3 /8 NPT s A D & TB TD are Ported on Opposite Sides XK Double Acting Nonrotating Note : s J, K, TJ, & TK have two #0-32 x.50 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.97 Pull area =.78 Seal Kits for Series: Original = 2-SK-K "T" = 2-SKG-K 7/6 x. Wrench Flat Random Rotation Rod Rotation Tolerance ± B2.4 K2.99 5/6-24 x E2.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS J, K, TJ & TK See Note.50 Rod Dia. Y2 Z2.3 /8 NPT s A D & TB TD are Ported on Opposite Sides Original Series "T" Series, Inches /8 3/6 /4 /2 3/4 /4 /2 3/4 2 3 4 /6 /8 3/8 5/8 7/8 /8 3/8 5/8 7/8 2 7/8 37/8, Letter A B C D X E F G H I J K TB TC TD TX TE TF TG TH TI TJ TK X Double Acting X Double Acting B.02.02.02.33.77 2.02 2.27 2.52 2.95 3.39 3.99 4.99.02.02.33.77 2.02 2.27 2.52 2.95 3.39 3.99 4.99 E.38.38.38.38.63.63.63.63.63.63.63.63.38.38.38.63.63.63.63.63.63.63.63 K.69.69.69.00.44.69.94 2.9 2.62 3.06 Note Note.69.69.00.44.69.94 2.9 2.62 3.06 Note Note Y.45.45.45.67.52.52.52.52.70.89.52.52.45.45.67.52.52.52.52.70.89.52.52 Z.45.45.45.67.27.52.77 2.02 2.45 2.89 3.49 4.49.45.45.67.27.52.77 2.02 2.45 2.89 3.49 4.49 Weight, lb..28.27.26.37.48.54.6.67.8.95.08.35.28.27.38.49.55.62.68.82.96.09.36 XK Double Acting, Nonrotating XK Double Acting, Nonrotating B2.02.02.02.33.77 2.02 2.27 2.52 2.95 3.39 3.99 4.99.02.02.33.77 2.02 2.27 2.52 2.95 3.39 3.99 4.99 E2.38.38.38.38.63.63.63.63.63.63.63.63.38.38.38.63.63.63.63.63.63.63.63 K2.69.69.69.00.44.69.94 2.9 2.62 3.06 Note Note.69.69.00.44.69.94 2.9 2.62 3.06 Note Note Y2.45.45.45.67.52.52.52.52.70.89.52.52.45.45.67.52.52.52.52.70.89.52.52 Z2.45.45.45.67.27.52.77 2.02 2.45 2.89 3.49 4.49.45.45.67.27.52.77 2.02 2.45 2.89 3.49 4.49 Weight, lb..28.27.26.37.49.55.62.68.83.97.0.38.28.27.38.50.56.63.69.84.98..39 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.02.02.02.33 2.02 2.27 2.95 3.39 3.99 3.99 NA* NA*.02.02.33 2.02 2.27 2.95 3.39 3.99 3.99 NA* NA* E3.38.38.38.38.63.63.63.63.63.63 " ".38.38.38.63.63.63.63.63.63 " " K3.69.69.69.00.69.94 2.62 3.06 Note Note " ".69.69.00.69.94 2.62 3.06 Note Note " " Y3 Vent.52.52.70.89.52.52 " " Vent.52.52.70.89.52.52 " " Z3.45.45.45.67.52.77 2.45 2.89 3.49 3.49 " ".45.45.67.52.77 2.45 2.89 3.49 3.49 " " Weight,. lb..28.28.28.34.57.63.84.98.5.5 " ".29.29.35.58.65.85.99.6.6 " " Preload, lb. 6.0 5.0 4.0 3.8 4.4 3.7 5.0 4.6 2.5 2.8 " " 5.0 4.0 3.8 4.4 3.7 5.0 4.6 2.5 2.8 " " End of, lb. 8.5 8.5 8.5.8 7.7 8.6 7.8 8.3 22.2 7.7 " " 8.5 8.5.8 7.7 8.6 7.8 8.3 22.2 7.7 " " OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4.40.46.52 2.08 3.02 3.52 4.45 5.4 NA* NA* NA* NA*.33.40.96 2.90 3.40 4.33 5.02 NA* NA* NA* NA* E4.38.38.38.38.63.63.63.63 " " " ".38.38.38.63.63.63.63 " " " " K4.94.94.94.25.94 2.9 2.87 3.3 " " " ".94.94.25.94 2.9 2.87 3.3 " " " " Y4.58.64.70.7.27.52.95 2.39 " " " ".5.58.05.5.40.83 2.27 " " " " Z4.58.64.70.7 2.27 2.77 3.70 4.39 " " " ".5.58.05 2.5 2.65 3.58 4.27 " " " " Weight, lb..37.36.36.43.63.70.9.00 " " " ".37.37.44.65.72.92.0 " " " " Preload, lb. 6.0 5.0 4.0 3.5 3.9 3.3 2.5 4.3 " " " " 5.0 4.0 3.5 6. 5. 4.0 5.5 " " " " End of, lb. 8.5 8.5 8.5.5 7. 8.2 6.8 8. " " " " 8.5 8.5 8.5 7. 8.2 6.8 8. " " " " N/A* = Not Available O Single Acting Spring Retracted Note : s H, I, TH & TI have two #0-32 x.50 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts. Push area =.99 See chart for Spring Forces: Preload and End of. Seal Kits for Series: Original = 2-SK "T" = 2-SKG 7/6 x. Wrench Flat.50 Rod Dia. Rod End Face.4 B3 K3 /8 NPT.99 Y3 5/6-24 x E3.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS H, I, TH & TI See Note.40 Rod End Vent s A D & TB TD Z3 Rod End Vent s X I & TX TI.3 OP Single Acting Spring Extended See page.6 for Mounting Bolts. Pull area =.80 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 2-SK "T" = 2-SKG 7/6 x. Wrench Flat B4.4 + K4.99 Y4 5/6-24 x E4.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.50 Rod Dia. /8 NPT s A D & TB TD are Ported on Opposite Sides Z4.38 2-3-08 NA* = Not Available.30
-/8" (2) Bore Also See Pg..30 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 28.5mm Bore Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.7. Original Series mm 3.2 4.8 6.4 2.7 9. 25.4 3.8 38. 44.5 50.8 76.2 0.6 Letter A B C D X E F G H I J K T Series mm.6 3.2 9.5 5.9 22.2 28.6 34.9 4.3 47.6 73.0 96.4 Letter TB TC TD TX TE TF TG TH TI TJ TK Mounting Holes 5.3mm Diameter Thru 8.8mm C'Bore x 5.3mm Dp. 2 Places for M5 SHCS Except strokes J, K, TJ & TK which have two M5 x 2.0mm Dp. Tapped Mounting Holes on each end. Thread Pitches M5 = 0.8mm M8 =.25mm M8 x 9.0 Conversion Factor Inches x 25.4 = mm 42.8mm Bolt Circle Standard Female Rod Thread M8. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original and T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.30. Also see Option Information on pages.7 thru.5. Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3..8 + B See Page.30.37.56 Note.69.3.00.2 Note : Hole Diameter =.335 Pin Diameter =.325 Pin (46 Stainless Steel) and Clips are included -PM Port Location IN LINE with Slot -SM Port Location to Slot T V Q H N C C7 LF LR LFR BF BR BFR -X -XK NA NA NA NA -O NA NA NA NA NA NA -OP NA NA NA Suffix Options -EPM & -ESM Eye Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3..8 + B See Page.30.57.30.37.56.335 -EPM Port Location IN LINE with Tang.00 -ESM Port Location to Tang Oil filled bushings Oil filled bushing EM-2 Eye Bracket Kit Mates with Clevis Mount above. Order separately..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.50.44.3.30.25.50.94.38 Hole.335 Oil filled bushing is standard.69 PM-2 Clevis Bracket Kit Mates with Eye Mount above. Order separately..27 Dia. 4 Places on Square Pattern for Flat Head Screws. Four /4-20 x 3/4" FH(#2)M Screws are included..88.3.50.2.00.3.46.94.32.25 Material: Zinc Die Casting.69 Hole.335 Pin.325 Pin (46 Stainless Steel) & Clips are included. Oil Filled Bushings are Standard. RC-3 Rod Clevis and Pin Threaded Stud mates with Female Rod thread in Pancake Cylinders. Slot & Pin Mate with EM-04 Eye Bracket shown on the right. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.25 Pin Diameter.250.88.6.96.50.39.75 5/6-24 Optional Metric #MRC-3 M8 x 9.7mm EM-04 Eye Bracket Kit Mates RC-3 Rod Clevis shown on the left..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.88.25.88.56.25.87.23 Hole.25 Oil filled bushing.6 is standard.4.3 2-3-08
-/8" (2) Bore Also See Pg..30 Option Specifications Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK, -O, -OP. 5/6-24 x 0.75 Also see Option Information on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.. 9/6 Hex Nut Adjusting Screw.042 Adjustment Per Revolution.7 s " & Shorter =.38 Max. + s " & Longer =.38 + Adjustment.3 + B Standard Adjustment is " (-OP Only Use B4 as shown on page.30. No additional length is required.) Suffix Option -F Threaded Nose Mount Available on Original and T Series with s: -X, -XK, -O, -OP -4 Also see Option Information on page.3..4.75.25.00+ B.99-4.59 3 /8 Hex.9 Part No. 200-95 Mounting Nut is included Material: Zinc Plated Steel Pilot Dia. =.000.995 Pilot Length =.3 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Note: Alloy steel mounting bolts may effect sensing. Stainless steel or other non-magnetic bolts are recommended. /4" 60 Dovetail Profile of Sensor & Mounting Slot. /8" (2) Bore Sensors available for D & TD strokes and longer. s D & TD are ported on opposite sides. #2 40 40 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Sensors Must be Ordered Separately See Sensor Models Available page.4 Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series X XK /2------------- D------ Not Available 3/4--------------X--------------X ----------------E--------------E /4-----------F--------------F /2---------- G------------- G 3/4---------- H--------------H 2---------------- I--------------- I 3----------------J--------------J 4----------------K--------------K Available on T Series X XK 3/8----------- TD------ Not Available 5/8----------- TX------------TX 7/8----------- TE------------TE /8--------- TF------------TF 3/8---------TG----------- TG 5/8--------- TH------------TH 7/8----------TI------------ TI 2 7/8-------- TJ------------TJ 3 7/8--------- TK------------TK Suffix Option -AS Adjustable Extend Available on Original Series with s: -X, -XK, -O Also see Option Information on page.. BB D C E Inches /8 3/6 /4 /2 3/4 -/4 -/2-3/4 2 3 4 Letter A B C D X E F G H I J K s: -X, -XK BB.36.36.36.67 2. 2.36 2.6 2.86 3.30 3.74 4.33 5.33 s:-o BB.36.36.36.67 2.36 2.6 3.30 3.74 4.33 4.33 NA NA C.40.53.66 2.6 2.66 3.6 3.66 4.6 4.66 5.6 7.6 9.6 D 0.63 0.69 0.75.00.25.50.75 2.00 2.25 2.50 3.50 4.50 E 0.63 0.69 0.75.00.25.50.75 2.00 2.25 2.50 3.50 4.50.50 Dia..3 Dia..050 Adjustment Per Revolution 2-5-08.32
-/8" (2) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting Note : s J & K have two #0-32 x.50 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.80 Seal Kit = 2-SK, Inches /8 3/6 /4 /2 3/4 /4 /2 3/4 2 3 4, Letter A B C D X E F G H I J K B.36.36.36.67 2. 2.36 2.6 2.86 3.30 3.74 4.33 5.33 E.38.38.38.34.63.63.63.63.63.63.63.63 K.04.04.04.34.78 2.03 2.28 2.53 2.96 3.40 Note Note Y.45.45.45.67.52.52.52.52.70.89.52.52 Z.45.45.45.67.27.52.77 2.02 2.45 2.89 3.49 4.49 Weight, lb..46.45.44.55.68.76.83.9.07.22.4.7 7/6 x. Wrench Flat B.4 K.4 +.99 /8 NPT Y 5/6-24 x E.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS J & K See Note.50 Rod Dia. Z.47 s A D are Ported on Opposite Sides XDRK Original Series Double Rod, Double Acting, Nonrotating Note : s J & K have two #0-32 x.50 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.78 Seal Kit = 2-SK-K 7/6 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4.99 5/6-24 x E.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS J & K See Note.50 Rod Dia., Inches /8 3/6 /4 /2 3/4 /4 /2 3/4 2 3 4, Letter A B C D X E F G H I J K B.36.36.36.67 2. 2.36 2.6 2.86 3.30 3.74 4.33 5.33 E.38.38.38.34.63.63.63.63.63.63.63.63 K.04.04.04.34.78 2.03 2.28 2.53 2.96 3.40 Note Note Y.45.45.45.67.52.52.52.52.70.89.52.52 Z.45.45.45.67.27.52.77 2.02 2.45 2.89 3.49 4.49 Weight, lb..47.46.45.56.69.77.84.93.09.24.43.74 Y B Z K.47.4 + /8 NPT s A D are Ported on Opposite Sides ODR Original Series Double Rod, Single Acting, Spring Retracted Note : s H & I have two #0-32 x.50 Tapped Mounting Holes on each end. See page.6 for Mounting Bolts Force Area =.80 Seal Kit = 2-SK, Inches /8 3/6 /4 /2 3/4 /4 /2 3/4 2, Letter A B C D X E F G H I B.36.36.36.67 2.36 2.6 3.30 3.74 4.33 4.33 E.38.38.38.34.63.63.63.63.63.63 K.04.04.04.34 2.03 2.28 2.96 3.40 Note Note Y Rod End Vent Face.52.52.70.89.52.52 Z.45.45.45.67.52.77 2.45 2.89 3.49 3.49 Weight, lb..44.44.43.53.76.83.07.22.4.4 Spring Return Forces, lb. Preload 6.0 5.0 4.0 3.5 4.4 3.7 2.8 4.6 2.8 2.8 End of 8.5 8.5 8.5.5 7.7 8.6 7. 8.3 5.8 7.7 7/6 x. Wrench Flat.50 Rod Dia. B.4 K.4 +.99 /8 NPT 5/6-24 x E.69 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS H & I See Note.40 Rod End Vent s A D Rod End Vent s X I Y Z.47.33 4-22-04
-/8" (2) Bore Also See Pg..33 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 50.8mm Bore Available on Original Series with s: -XDR, -XDRK, -ODR Also see Option Information on page.7. mm 3.2 4.8 6.4 2.7 9. 25.4 3.8 38. 44.5 50.8 76.2 0.6 Letter A B C D X E F G H I J K Mounting Holes 5.3mm Diameter Thru 8.8mm C'Bore x 5.3mm Dp. 2 Places for M5 SHCS Except strokes J, K, TJ & TK which have two M5 x 2.0mm Dp. Tapped Mounting Holes on each end. Thread Pitches M5 = 0.8mm M8 =.25mm 42.8mm Bolt Circle Standard Female Rod Thread M8. Male Rod Thread Option -MR shown. M8 x 9.0 Conversion Factor Inches x 25.4 = mm G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.33. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR 3 6 -XDR -XDRK NA NA NA NA NA -ODR NA NA NA NA NA NA Suffix Options -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use MR For Cap End only use MR For Both Ends use MR2 Also see Option Information on Page.8. 5/6-24 x 0.75 Suffix Options -F, -F, -F2 Threaded Nose Mount Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use -F For Cap End only use -F For Both Ends use -F2 Also see Option Information page.3..99-4 Pilot Dia. =.000.995 Pilot Length =.3-4.59 3 /8 Hex.9.4.25.75.00+ B.4 + Part No. 200-95 Mounting Nut is included Material: Zinc Plated Steel Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) Sensors Must Be Ordered Separately s are NOT affected by magnetic piston. See Sensor Models Available page.4 /8" (2) Bore Note: Alloy steel mounting bolts may effect sensing. Stainless steel or other non-magnetic bolts are recommended. /4" 60 Dovetail Profile of Sensor & Mounting Slot. Sensors available for D strokes and longer. D is ported on opposite sides. #2 40 40 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series XDR XDRK /2------------- D------ Not Available 3/4--------------X--------------X ----------------E--------------E /4-----------F--------------F /2---------- G------------- G 3/4---------- H--------------H 2---------------- I--------------- I 3----------------J--------------J 4----------------K--------------K 2-5-08.34
5/8" (22) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired Suffix Options D 22 X MR Metric M See pages.7,.37 &.40 Bore Code 5/8" 22 4.3mm 22 Standard s Original Series X XK XDR O XDRK ODR OP /8 AA AA AA /4 A* A A /2 B B B 3/4 C C C D D D /2 E E 2 F 3 G 4 H T Series Includes PTFE piston bearing X XK O OP /4 TB TB TB /2 TC TC TC 3/4 TD TD TD /4 TE TE 3/4 TF 2 3/4 TG 3 3/4 TH Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E *Note Sensors not available: A-22-XK A-22-XDRK Single rod Double acting -X Double acting, Nonrotating Internal guide pins - 50 psi max -XK Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Double acting, Nonrotating Internal guide pins - 50 psi max -XDRK Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.36 &.39 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 22 for 5/8" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 3 / 4 "---------------- 7------------------.23 / 8 "------------2----------------.29 2"----------------32----------------.4 2 / 2 "------------52----------------.47 3"----------------72----------------.53 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES B-22-X Original Series, /2" stroke - 5/8" Bore - Single Rod, Double Acting TC-22-O-MR T Series, /2" - 5/8" Bore - Single Rod, Spring Retract - Male Rod Thread Suffix Options Male rod thread: Single rod -MR Double rod, rod end -MR Double rod, cap end -MR Double rod, both ends -MR2 PTFE seals -T Viton seals -V Quad seals -Q External guide, nonrotating for load guiding (See page.65) -G Hydraulic: Standard cover -H Thick cover -HHC Air service: Thick cover -HC /4 NPT ports -P4 Hole thru double rod shaft: / 8 " hole -3 Plus size: /4" hole -25 50 psi max Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Sound limiters: Rod end -LF Cap end -LR Both ends -LFR Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable extend stroke (Full stroke adjustment is standard) -AS Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot Ports to slot -PM -SM Eye mount: Ports in-line with tang Ports to tang -EPM -ESM Threaded nose mount: Single rod -F Double rod, rod end -F Double rod, cap end -F Double rod, both ends -F2 Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.38,.40 See pages.3.5 for general option information. and pages.37,.38 &.40 for option specifications of 5/8" bore models. A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com.35 6-3-02
-5/8" (22) Bore Single Rod Standard Specifications X Double Acting /2 x. Wrench Flat.4 2.74 3/8-24 x E 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.62 Rod Dia. XK Double Acting Nonrotating /2 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4 2.74 3/8-24 x E2 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.62 Rod Dia. See page.6 for Mounting Bolts. Push area = 2.07 Pull area =.76 Seal Kits for Series: Original = 22-SK "T" = 22-SKG B K Y Z /8 NPT s AA A are Ported on Opposite Sides.3 See page.6 for Mounting Bolts. Push area = 2.0 Pull area =.70 Seal Kits for Series: Original = 22-SK-K "T" = 22-SKG-K B2 K2 Y2 Z2 /8 NPT s AA A are Ported on Opposite Sides.25 Original Series "T" Series, Inches /8 /4 /2 3/4 /2 2 3 4 /4 /2 3/4 /4 3/4 2 3/4 3 3/4, Letter AA A B C D E F G H TB TC TD TE TF TG TH X Double Acting X Double Acting B.4.27.77 2.02 2.33 2.83 3.33 4.33 5.33.77 2.02 2.33 2.83 3.33 4.33 5.33 E.38.44.63.63.75.75.75.75.75.63.63.75.75.75.75.75 K.8.94.44.69 2.00 2.50 3.00 4.00 5.00.44.69 2.00 2.50 3.00 4.00 5.00 Y.64.64.52.52.52.52.52.52.52.52.52.52.52.52.52.52 Z.64.64.27.52.83 2.33 2.83 3.83 4.83.27.57.83 2.33 2.83 3.83 4.83 Weight, lb..60.64.93.06.9.43.66 2.4 2.60.99.2.25.49.72 2.20 2.66 XK Double Acting, Nonrotating XK Double Acting, Nonrotating B2.27.40.90 2.5 2.46 2.96 3.46 4.46 5.46.90 2.5 2.46 2.96 3.46 4.46 5.46 E2.38.44.63.63.75.75.75.75.75.63.63.75.75.75.75.75 K2.94.06.57.82 2.3 2.63 3.3 4.3 5.3.57.82 2.3 2.63 3.3 4.3 5.3 Y2.64.64.52.52.52.52.52.52.52.52.52.52.52.52.52.52 Z2.64.64.27.52.83 2.33 2.83 3.83 4.83.27.57.83 2.33 2.83 3.83 4.83 Weight, lb..68.72.02.5.29.53.77 2.27 2.74.08.2.35.59.83 2.83 3.80 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.4.27.77 2.02 2.33 4.33 NA* NA* NA*.77 2.02 2.33 4.33 NA* NA* NA* E3.38.44.63.63.75.75 NA* NA* NA*.63.63.75.75 NA* NA* NA* K3.8.94.44.69 2.00 4.00 NA* NA* NA*.44.69 2.00 4.00 NA* NA* NA* Y3 Vent.52 NA* NA* NA* Vent.52 NA* NA* NA* Z3.64.77.27.52.83 3.83 NA* NA* NA*.27.57.83 3.83 NA* NA* NA* Weight,. lb..58.63.89.00.5 2.0 NA* NA* NA*.95.06.2 2.6 NA* NA* NA* Preload, lb. 5.0 8.5 8.5 6.0 4.8 6.0 NA* NA* NA* 8.5 8.5 6.0 7.06 NA* NA* NA* End of, lb. 20.0 20.0 20.0 8.0 20.0 8.0 NA* NA* NA* 20.0 20.0 8.0 20.0 NA* NA* NA* OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4.65.89 2.64 3.4 3.83 NA* NA* NA* NA* 2.39 2.89 3.58 NA* NA* NA* NA* E4.38.44.63.63.75 NA* NA* NA* NA*.63.63.75 NA* NA* NA* NA* K4.9.32.82 2.07 2.50 NA* NA* NA* NA*.82 2.07 2.50 NA* NA* NA* NA* Y4.77.89.02.27.52 NA* NA* NA* NA*.77.02.27 NA* NA* NA* NA* Z4.77.89.77 2.27 2.83 NA* NA* NA* NA*.52 2.07 2.58 NA* NA* NA* NA* Weight, lb..8.83.0.20.42 NA* NA* NA* NA*.6.26.48 NA* NA* NA* NA* Preload, lb. 8.5 4.5 5.5 4.0 4.8 NA* NA* NA* NA* 4.5 5.5 4.0 NA* NA* NA* NA* End of, lb. 5.0 5.0 8.5 7.5 20.0 NA* NA* NA* NA* 5.0 8.5 7.5 NA* NA* NA* NA* O Single Acting /2 x. Spring Retracted Wrench Flat.62 Rod Dia. See page.6 for Mounting Bolts. Push area = 2.07 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 22-SK "T" = 22-SKG 2-3-08 Rod End Face B3.4 K3 /8 NPT 2.74 Y3 Z3 3/8-24 x E3 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.66 Rod End Vent s AA-D & TB - TD Rod End Vent s E & TE.3 OP Single Acting Spring Extended See page.6 for Mounting Bolts. Pull area =.76 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 22-SK "T" = 22-SKG B4 /2 x. Wrench Flat.4 + K4 2.74 3/8-24 x E4 Y4 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.62 Rod Dia. Z4 /8 NPT s AA A are Ported on Opposite Sides NA* = Not Available For s AA-C =.50 D =.63 TB-TC =.50 TD =.63.36
-5/8" (22) Bore Also See Page.36 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 4.3mm Bore Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.7. Original Series mm 3.2 6.4 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AA A B C D E F G H T Series mm 6.4 2.7 9. 3.8 44.5 69.9 95.3 Letter TB TC TD TE TF TG TH Mounting Holes 5.3mm Diameter Thru 8.8mm C'Bore x 5.3mm Dp. 2 Places for M5 SHCS Thread Pitches M5 = 0.8mm M0 =.5mm Conversion Factor Inches x 25.4 = mm M0 x 22.2 60.3mm Bolt Circle Standard Female Rod Thread M0. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original and T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.36. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 -X -XK NA NA NA NA -O NA NA NA NA NA NA -OP NA NA NA Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3. Suffix Options -EPM & -ESM Eye Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3. Chart Also see page.36.37.68 Note.69 -X, -O -XK -OP -OP.38.25.48 Chart Dimension All s.88 + B All s.75 + B AA-C s.94 + B D.8 + B -PM Port Location IN LINE with Slot Note : Hole Diameter =.376 Pin Diameter =.3750 -SM Port Location to Slot Pin (46 Stainless Steel) & Clips are included Chart Also see page.36.60.35.37.68.376 -X, -O -XK -OP -OP Oil filled bushing Chart Dimension All s.88 + B All s.75 + B AA-C s.94 + B D.8 + B -EPM Port Location IN LINE with Tang.25 -ESM Port Location to Tang Oil filled bushings EM-22 Eye Bracket Kit Mates with Clevis Mount shown above. Order separately..27 Dia. 4 Places for Flat Head Screws Four /4-20 x " FHSCS Screws are included Material: Zinc Die Casting.56.50 2.00.8.50.3 2.00.69.36 Hole.376 Oil filled bushing.3 is standard PM-22 Clevis Bracket Kit Mates with Eye Mount shown above. Order separately..25.50 2.00.27 Dia. 4 Places on Square Pattern for Flat Head Screws. Four /4-20 x " FHSCS Screws are included..48.25.38.3.52.00.38 Material: Zinc Die Casting.69 Hole.376 Pin.3750 Pin (46 Stainless Steel) & Clips included. Oil Filled Bushings are Standard. RC-38 Rod Clevis and Pin Threaded Stud mates with Female Rod thread in Pancake Cylinders. Slot & Pin Mate with EM-2 Eye Bracket shown on the right. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.32 Pin Diameter.325.25.63.2.63. 6.00 3/8-24 x.37 Optional Metric #MRC-38 M0 x 9.4 EM-2 Eye Bracket Kit Mates RC-38 Rod Clevis shown on the left..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.50.44.50.3.30.25.94.38 Hole.335 Oil filled bushing is standard.69.37 6-6-05
-5/8" (22) Bore Also See Page.36 Option Specifications Suffix Options -HHC Hydraulic & -HC Air Available on Original and T Series with -X, -O. Also see Option Information.2 + B on page.9 for Pressure.2 + K and Mounting details..25 Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK, -O, -OP. 3/8-24 x 0.88 Also see Option Information on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.. /6 Hex Nut Adjusting Screw.050 Adjustment Per Revolution Suffix Option -F Threaded Nose Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3..4.75.99 /4-2 /4-2.88 5 /8 Hex.25 Part No. 2200-95 Mounting Nut is included Material: Zinc Plated Steel.9 s " & Shorter =.38 Max. + s " & Longer =.38 + Adjustment.3 + B Standard Adjustment is " (-XK Only Use B2 as shown on page.36. No additional length is required.) (-OP Only Use B4 as shown on page.36. No additional length is required.).25.00+ B Pilot Dia. =.250.245 Pilot Length =.3 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) /4" 60 Dovetail Profile of Sensor & Mounting Slot. 5/8" (22) Bore Sensors available for A & TB strokes and longer. A is ported on opposite sides. #2 45 45 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Sensors Must be Ordered Separately See Sensor Models Available page.4 Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series X XK /4-----------------A-------Not Available /2-----------------B---------------B 3/4---------------- C---------------C ------------------ D---------------D /2--------------E---------------E 2-------------------F---------------F 3------------------ G-------------- G 4------------------ H---------------H Available on T Series X, XK /4--------------- TB /2--------------- TC 3/4--------------- TD /4------------ TE 3/4------------ TF 2 3/4------------ TG 3 3/4------------ TH Suffix Option -AS Adjustable Extend Available on Original Series with s: -X, -XK, -O Also see Option Information on page.. BB D C E Inches /8 /4 /2 3/4 -/2 2 3 4 Letter AA A B C D E F G H s: -X, -XK BB.6.74 2.24 2.49 2.80 3.30 3.80 4.80 5.80 s:-o BB.6.74 2.24 2.49 2.80 4.80 NA NA NA C.40.66 2.6 2.66 3.6 4.6 5.6 7.6 9.6 D 0.63 0.75.00.25.50 2.00 2.50 3.50 4.50 E 0.63 0.75.00.25.50 2.00 2.50 3.50 4.50.50 Dia..3 Dia..050 Adjustment Per Revolution 2-5-08.38
-5/8" (22) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting See page.6 for Mounting Bolts Force Area =.76 Seal Kit = 22-SK, Inches /8 /4 /2 3/4 /2 2 3 4, Letter AA A B C D E F G H B.6.74 2.24 2.49 2.80 3.30 3.80 4.80 5.80 E.38.44.63.63.75.75.75.75.75 K.28.4.9 2.6 2.47 2.97 3.47 4.47 5.47 Y.64.64.52.52.52.52.52.52.52 Z.64.64.27.52.83 2.33 2.83 3.83 4.83 Weight, lb..97.03.35.46.63.9 2.9 2.73 3.28 /2 x. Wrench Flat B.4 K.4 + 2.74 3/8-24 x E 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.62 Rod Dia. /8 NPT s AA A are Ported on Opposite Sides Y Z.60 XDRK Original Series Double Rod, Double Acting, Nonrotating See page.6 for Mounting Bolts Force Area =.70 Seal Kit = 22-SK-K, Inches /8 /4 /2 3/4 /2 2 3 4, Letter AA A B C D E F G H B.6.74 2.24 2.49 2.80 3.30 3.80 4.80 5.80 E.38.44.63.63.75.75.75.75.75 K.28.4.9 2.6 2.47 2.97 3.47 4.47 5.47 Y.64.64.52.52.52.52.52.52.52 Z.64.64.27.52.83 2.33 2.83 3.83 4.83 Weight, lb..05..44.55.73 2.0 2.30 2.86 3.42 /2 x. Wrench Flat Random Rotation Rod Rotation Tolerance ± B.4 K.4 + 2.74 3/8-24 x E 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.62 Rod Dia. /8 NPT s AA A are Ported on Opposite Sides Y Z.60 ODR Original Series Double Rod, Single Acting, Spring Retracted See page.6 for Mounting Bolts Force Area =.76 Seal Kit = 22-SK, Inches /8 /4 /2 3/4 /2, Letter AA A B C D E B.6.74 2.24 2.49 2.80 4.80 E.38.44.63.63.75.75 K.28.4.9 2.6 2.47 4.47 Y Rod End Vent Face.52 Z.64.77.27.52.83 3.83 Weight, lb..95.0.30.42.58.86 Spring Return Forces, lb. Preload 5.0 8.5 8.5 6.0 4.8 6.0 End of 20.0 20.0 20.0 8.0 20.0 8.0 /2 x. Wrench Flat.62 Rod Dia. B.4 K.4 + 2.74 3/8-24 x E 2.38 Bolt Circle.20 Dia. Thru.32 C'Bore x.9 Dp. for 2, #0 SHCS.66 Rod End Vent s AA D Rod End Vent E Y Z.60.39 /8 NPT 4-22-04
-5/8" (22) Bore Also See Page.39 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 4.3mm Bore Available on Original Series with s: -XDR, -XDRK, -ODR Also see Option Information on page.7. Mounting Holes 5.3mm Diameter Thru 8.8mm C'Bore x 5.3mm Dp. 2 Places for M5 SHCS Thread Pitches M5 = 0.8mm M0 =.5mm 60.3mm Bolt Circle mm 3.2 6.4 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AA A B C D E F G H Conversion Factor Inches x 25.4 = mm M0 x 22.2 Standard Female Rod Thread M0. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.39. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 3 25 -XDR -XDRK NA NA NA NA -ODR NA NA NA NA NA NA Suffix Options -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use MR For Cap End only use MR For Both Ends MR2 Also see Option Information on Page.8. 3/8-24 x 0.88 Suffix Options -F, -F, -F2 Threaded Nose Mount Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use -F For Cap End only use -F For Both Ends use -F2 Also see Option Information on page.3..99 / 4-2.4.25.75.00+ B Pilot Dia. =.250.245.4 + Pilot Length =.3 /4-2.88 5 /8 Hex.25 Part No. 2200-95 Mounting Nut is included Material: Zinc Plated Steel Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. /4" 60 Dovetail Profile of Sensor & Mounting Slot. Sensors available for A strokes and longer. A is ported on opposite sides. #2 5/8" (22) Bore 45 45 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Sensors Must be Ordered Separately See Sensor Models Available page.4 Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series XDR XDRK /4-----------------A-------Not Available /2-----------------B---------------B 3/4---------------- C---------------C ------------------ D---------------D /2--------------E---------------E 2-------------------F---------------F 3------------------ G-------------- G 4------------------ H---------------H 2-5-08.40
2" (32) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired D 32 X Suffix Options MR Metric M See pages.7,.43 &.46 Bore Code 2" 32 50.8mm 32 Standard s Original Series X XK XDR O XDRK ODR OP /8 AB AB AB /4 AA AA AA 3/8 A A A /2 B B B 3/4 C C C D D D /2 E E 2 F 3 G 4 H T Series Includes PTFE piston bearing X XK O OP /8 TA TA TA /4 TB TB TB /2 TC TC TC 3/4 TD TD TD /4 TE TE 3/4 TF 2 3/4 TG 3 3/4 TH Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E Single rod Double acting -X Double acting, Nonrotating Internal guide pins - 50 psi max -XK Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Double acting, Nonrotating Internal guide pins - 50 psi max -XDRK Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.42 &.45 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 32 for 2" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 3 / 4 "---------------- 7------------------.23 / 8 "------------2----------------.29 5 / 8 "------------22----------------.35 2 / 2 "------------52----------------.47 3"----------------72----------------.53 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES B-32-X Original Series, /2" stroke - 2" Bore - Single Rod, Double Acting TD-32-X-MR T Series, 3/4" - 2" Bore - Single Rod, Double Acting - Male Rod Thread Suffix Options Male rod thread: Single rod -MR Double rod, rod end -MR Double rod, cap end -MR Double rod, both ends -MR2 PTFE seals -T Viton seals -V Quad seals -Q External guide, nonrotating for load guiding (See page.65) -G Hydraulic: Standard cover -H Thick cover -HHC Air service: Thick cover -HC /4 NPT ports -P4 Hole thru double rod shaft: 5 / 32 " hole -6 Plus size 5 / 6 " hole -3 50 psi max Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Sound limiters: Rod end -LF Cap end -LR Both ends -LFR Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable extend stroke (Full stroke adjustment is standard) -AS Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot Ports to slot -PM -SM Eye mount: Ports in-line with tang Ports to tang -EPM -ESM Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.44,.46 See pages.3.5 for general option information and pages.43,.44 &.46 for option specifications of 2" bore models. A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com.4 6-3-02
2" (32) Bore Single Rod Standard Specifications X Double Acting 5/8 x. Wrench Flat.4 72 3.24 /2-20 x E 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS.75 Rod Dia. XK Double Acting Nonrotating 5/8 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4 72 3.24 /2-20 x E2 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS.75 Rod Dia. See page.6 for Mounting Bolts. Push area = 3.4 Pull area = 2.70 Seal Kits for Series: Original = 32-SK "T" = 32-SKG B K Y Z.3 /8 NPT s AB A & TA are Ported on Opposite Sides See page.6 for Mounting Bolts. Push area = 2.94 Pull area = 2.50 Seal Kits for Series: Original = 32-SK-K "T" = 32-SKG-K B2 K2 Y2 Z2.25 /8 NPT s AB A & TA are Ported on Opposite Sides Original Series "T" Series, Inches /8 /4 3/8 /2 3/4 /2 2 3 4 /8 /4 /2 3/4 /4 3/4 2 3/4 3 3/4, Letter AB AA A B C D E F G H TA TB TC TD TE TF TG TH X Double Acting X Double Acting B.20.33.45.64 2.02 2.39 2.89 3.39 4.39 5.39.45.64 2.02 2.39 2.89 3.39 4.39 5.39 E.40.50.63.63.75.88.88.88.88.88.63.63.75.88.88.88.88.88 K.80.93.05.24.62.99 2.49 2.99 3.99 4.99.05.24.62.99 2.49 2.99 3.99 4.99 Y.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52 Z.70.83.95.4.52.89 2.39 2.89 3.89 4.89.95.4.52.89 2.39 2.89 3.89 4.89 Weight, lb..89.96.04.6.45.70 2.02 2.34 2.97 3.58.0.30.56.84 2.6 2.48 3. 3.7 XK Double Acting, Nonrotating XK Double Acting, Nonrotating B2.33.46.58.77 2.5 2.52 3.02 3.52 4.52 5.52.58.77 2.5 2.52 3.02 3.52 4.52 5.52 E2.40.50.63.63.75.88.88.88.88.88.63.63.75.88.88.88.88.88 K2.93.06.8.37.75 2.2 2.62 3.2 4.2 5.2.8.37.75 2.2 2.62 3.2 4.2 5.2 Y2.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52 Z2.70.83.95.4.52.89 2.39 2.89 3.89 4.89.95.4.52.89 2.39 2.89 3.89 4.89 Weight, lb..02.09.8.30.60.85 2.9 2.52 3.8 3.82.24.44.7 2.00 2.33 2.66 3.32 3.95 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.20.33.45.64 2.02 2.39 4.39 NA* NA* NA*.45.64 2.02 2.39 4.39 NA* NA* NA* E3.40.50.63.63.75.88.88 NA* NA* NA*.63.63.75.88.88 NA* NA* NA* K3.80.93.05.24.62.99 3.99 NA* NA* NA*.05.24.62.99 3.99 NA* NA* NA* Y3 Vent.52 NA* NA* NA* Vent.52 NA* NA* NA* Z3.70.83.95.4.52.89 3.89 NA* NA* NA*.95.4.52.89 3.89 NA* NA* NA* Weight,. lb..85.97.0.3.36.6 3. NA* NA* NA*.0.3.36.6 3.25 NA* NA* NA* Preload, lb. 2.0 6.2 2.0 7.0 5.0 4.7 5.0 NA* NA* NA*.3 7.3 6.2 7.6 4.8 NA* NA* NA* End of, lb. 8.0 8.0 2.0 20.0 5.5 20.0 20.0 NA* NA* NA* 2.0 20.0 5.5 20.0 20.0 NA* NA* NA* OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4.7.96 2.2 2.52 3.4 3.89 NA* NA* NA* NA*.96 2.27 2.89 3.6 NA* NA* NA* NA* E4.40.50.63.63.75.88 NA* NA* NA* NA*.63.63.75.88 NA* NA* NA* NA* K4.8.30.43.62.99 2.49 NA* NA* NA* NA*.43.62.99 2.49 NA* NA* NA* NA* Y4.65.77.90.02.27.52 NA* NA* NA* NA*.65.77.02.25 NA* NA* NA* NA* Z4.83.08.33.64 2.27 2.89 NA* NA* NA* NA*.08.33.64 2.27 NA* NA* NA* NA* Weight, lb..22.29.36.49.76 2.3 NA* NA* NA* NA*.50.63.89 2.26 NA* NA* NA* NA* Preload, lb. 8.5 4.5 9.5 7.0 6.0 4.7 NA* NA* NA* NA* 0.7 7.0 6.0 4.7 NA* NA* NA* NA* End of, lb. 5.0 5.0 20.0 20.0 8.0 20.0 NA* NA* NA* NA* 8.0 20.0 8.0 20.0 NA* NA* NA* NA* O Single Acting 5/8 x. Spring Retracted Wrench Flat.75 Rod Dia. See page.6 for Mounting Bolts. Push area = 3.4 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 32-SK "T" = 32-SKG 2-8-08 Rod End Face B3.4 K3 /8 NPT 72 3.24 /2-20 x E3 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS Y3 Z3.7 Rod End Vent s AB-D & TA - TD Rod End Vent s E & TE.3 OP 5/8 x. Single Acting Wrench Flat Spring Extended See page.6 for Mounting Bolts. B4 Pull area = 2.70 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 32-SK "T" = 32-SKG.4 + K4 72 3.24 Y4 /2-20 x E4 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS.75 Rod Dia. /8 NPT s AB A & TA are Ported on Opposite Sides Z4 NA* = Not Available s AB-C =.50 D =.63 TA-TC =.50 TD =.63.42
2" (32) Bore Also See Page.42 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 50.8mm Bore Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.7. Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 2 Places for M6 SHCS Thread Pitches M6 =.0mm M2 =.75mm 7.4mm Bolt Circle Original Series mm 3.2 6.4 9.5 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AB AA A B C D E F G H T Series mm 3.2 6.4 2.7 9. 3.8 44.5 69.9 95.3 Letter TA TB TC TD TE TF TG TH Conversion Factor Inches x 25.4 = mm M2 x 25.4 Standard Female Rod Thread M2. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original and T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.42. Also see Option Information on pages.7 thru.5. Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3. Chart Also see page.42.37.68 Note.69.38.25.48 Oil filled bushings Chart Dimension -X, -O All s.88 + B -XK All s.75 + B -OP AB-C s.94 + B -OP D.8 + B -PM Port Location IN LINE with Slot Note : Hole Diameter =.376 Pin Diameter =.3750 -SM Port Location to Slot Pin (46 Stainless Steel) & Clips are included T V Q H N C C7 LF LR LFR BF BR BFR P4 -X -XK NA NA NA NA -O NA NA NA NA NA NA -OP NA NA NA Suffix Options -EPM & -ESM Eye Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3. Chart Also see page.42.60.35.37.68.376 Oil filled bushing -X, -O -XK -OP -OP Chart Dimension All s.88 + B All s.75 + B AB-C s.94 + B D.8 + B -EPM Port Location IN LINE with Tang.25 -ESM Port Location to Tang EM-22 Eye Bracket Kit Mates with Clevis Mount above. Order separately..27 Dia. 4 Places for Flat Head Screws Four /4-20 x " FHSCS Screws are included Material: Zinc Die Casting.56 2.00.50.8.50.3 2.00.69.36 Hole.376 Oil filled bushing.3 is standard PM-22 Clevis Bracket Kit Mates with Eye Mount above. Order separately..52.69.27 Dia. 4 Places on Square Pattern for Flat Head Screws. Four /4-20 x " FHSCS Screws are included..25.50 2.00.48.25.38.3.00.38 Material: Zinc Die Casting Hole.376 Pin.3750 Pin (46 Stainless Steel) & Clips included. Oil Filled Bushings are Standard. RC-Chart Rod Clevis and Pin Threaded Stud mates with Female Rod thread in the Pancake Cylinders. Slot and Pin Mate with EM-2 Eye Bracket shown on the right. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.2.32.00.3.69.63. 6 Pin Diameter.325 CHART /2-20 x Thread Length Metric M2 x Thread Length Rod Clevis Number RC-54 RC-56 s AB AA A H Thread Length.39".62" MRC-54 MRC-56 MAB MAA 9.9mm MA MH 5.7mm EM-2 Eye Bracket Kit Mates with any Rod Clevis shown on the left..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.50.44.50.3.30.25.94.38 Hole.335 Oil filled bushing is standard.69.43 2-5-04
2" (32) Bore Also See Page.42 Option Specifications Suffix Option -HHC Hydraulic & -HC Air Available on Original and T Series with -X, -O. Also see Option Information.2 + B on page.9 for Pressure.2 + K and Mounting details..25 Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK, -O, -OP. /2-20 x.00 Also see Option Information on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.. /6 Hex Nut Adjusting Screw.050 Adjustment Per Revolution.9 s " & Shorter =.38 Max. + s " & Longer =.38 + Adjustment.3 + B Standard Adjustment is " (-XK Only use B2 as shown on page.42. No additional length is required.) (-OP Only use B4 as shown on page.42. No additional length is required.) Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 /4" 60 Dovetail Profile of Sensor & Mounting Slot. 2" (32) Bore Quick Reference to Standard s Use the appropriate Letter in the Model Number Sensors available for AA & TA strokes and longer. s AA A Available on Original Series Available on T Series and TA are ported on opposite sides. 72 X, XK X, XK #2 35 35 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only /4----------------AA 3/8-----------------A /2-----------------B 3/4---------------- C ----------------- D /2----------------E 2------------------F 3----------------- G 4----------------- H /8----------------TA /4----------------TB /2----------------TC 3/4----------------TD /4---------------TE 3/4---------------TF 2 3/4-------------- TG 3 3/4---------------TH Suffix Option -AS Adjustable Extend Available on Original Series with s: -X, -XK, -O Also see Option Information on page.. BB D C E Inches /8 /4 3/8 /2 3/4 -/2 2 3 4 Letter AB AA A B C D E F G H s: -X, -XK BB.83.95 2.08 2.27 2.64 3.02 3.52 4.02 5.02 6.02 s:-o BB.83.95 2.08 2.27 2.64 3.02 5.02 NA NA NA C.67.9 2.7 2.4 2.9 3.4 4.4 5.4 7.4 9.4 D 0.63 0.75 0.88.00.25.50 2.00 2.50 3.50 4.50 E 0.88.00.3.25.50.75 2.25 2.75 3.75 4.75.50 Dia. 2.00 Dia..063 Adjustment Per Revolution 2-5-08.44
2" (32) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting See page.6 for Mounting Bolts Force Area = 2.70 Seal Kit = 32-SK 5/8 x. Wrench Flat.4 72 3.24 /2-20 x E 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS.75 Rod Dia., Inches /8 /4 3/8 /2 3/4 -/2 2 3 4, Letter AB AA A B C D E F G H B.83.95 2.08 2.27 2.64 3.02 3.52 4.02 5.02 6.02 E.40.50.63.63.75.88.88.88.88.88 K.44.56.69.89 2.25 2.63 3.3 3.63 4.63 5.63 Y.52.52.52.52.52.52.52.52.52.52 Z.70.83.95.4.52.89 2.39 2.89 3.89 4.89 Weight, lb..56.64.72.86 2.5 2.44 2.80 3.8 3.94 4.72 B K.4 + /8 NPT s AB A are Ported on Opposite Sides Y Z.75 XDRK Original Series Double Rod, Double Acting, Nonrotating See page.6 for Mounting Bolts Force Area = 2.5 Seal Kit = 32-SK-K 5/8 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4 72 3.24 /2-20 x E 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS.75 Rod Dia., Inches /8 /4 3/8 /2 3/4 -/2 2 3 4, Letter AB AA A B C D E F G H B.83.95 2.08 2.27 2.64 3.02 3.52 4.02 5.02 6.02 E.40.50.63.63.75.88.88.88.88.88 K.44.56.69.89 2.25 2.63 3.3 3.63 4.63 5.63 Y.52.52.52.52.52.52.52.52.52.52 Z.70.83.95.4.52.89 2.39 2.89 3.89 4.89 Weight, lb..70.78.87 2.0 2.3 2.6 2.98 3.37 4.6 4.97 B K.4 + /8 NPT s AB A are Ported on Opposite Sides Y Z.75 ODR Original Series Double Rod, Single Acting, Spring Retracted See page.6 for Mounting Bolts Force Area = 2.70 Seal Kit = 32-SK, Inches /8 /4 3/8 /2 3/4 -/2, Letter AB AA A B C D E B.83.95 2.08 2.27 2.64 3.02 5.02 E.40.50.63.63.75.88.88 K.44.56.69.89 2.25 2.63 4.63 Y Vent.52 Z.70.83.95.4.52.89 3.89 Weight, lb..5.60.69.8 2.0 2.39 4.6 Spring Return Forces, lb. Preload 2.0 6.2 2.0 7.0 5.0 4.7 5.0 End of 8.0 8.0 2.0 20.0 5.5 20.0 20.0 5/8 x. Wrench Flat.7 Rod End Vent s AB D B /8 NPT.4 K.4 + 72 3.24 /2-20 x E 2.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 2, /4" SHCS Y.75 Rod Dia. Rod End Vent E Z.75.45 2-4-08
2" (32) Bore Also See Page.45 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 50.8mm Bore Available on Original Series with s: -XDR, -XDRK, -ODR Also see Option Information on page.7. mm 3.2 6.4 9.5 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AB AA A B C D E F G H Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 2 Places for M6 SHCS Thread Pitches M6 =.0mm M2 =.75mm Conversion Factor Inches x 25.4 = mm M2 x 25.4 7.4mm Bolt Circle Standard Female Rod Thread M2. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.45. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 6 3 -XDR -XDRK NA NA NA NA -ODR NA NA NA NA NA NA Suffix Options -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use MR For Cap End only use MR For Both Ends MR2 Also see Option Information on Page.8 /2-20 x.00 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 /4" 60 Dovetail Profile of Sensor & Mounting Slot. 2" (32) Bore Quick Reference to Standard s Use the appropriate Letter in the Model Number Sensors available for AA strokes and longer. s AA A are ported on opposite sides. Available on Original Series 72 #2 35 35 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only XDR, XDRK /4----------------AA 3/8-----------------A /2-----------------B 3/4---------------- C ----------------- D /2----------------E 2------------------F 3----------------- G 4----------------- H 2-5-08.46
2 /2" (52) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired C 52 X Suffix Options MR Metric M See pages.7,.49 &.52 Bore Code 2 /2" 52 63.5mm 52 Standard s Original Series X XK XDR O XDRK ODR OP /8 AB AB AB /4 AA AA AA /2 A A A 3/4 B B B C C C /2 D D 2 E 3 F 4 G T Series Includes PTFE piston bearing X XK O OP /4 TA TA TA /2 TB TB TB 3/4 TC TC TC /4 TD TD 3/4 TE 2 3/4 TF 3 3/4 TG Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E Single rod Double acting -X Double acting, Nonrotating Internal guide pins - 50 psi max -XK Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Double acting, Nonrotating Internal guide pins - 50 psi max -XDRK Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.48 &.5 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 52 for 2 /2" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 3 / 4 "---------------- 7------------------.23 / 8 "------------2----------------.29 5 / 8 "------------22----------------.35 2"----------------32----------------.4 3"----------------72----------------.53 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES A-52-X Original Series, /2" stroke - 2 /2" Bore - Single Rod, Double Acting TC-52-X-MR T Series, 3/4" - 2 /2" Bore - Single Rod, Double Acting - Male Rod Thread Suffix Options Male rod thread: Single rod -MR Double rod, rod end -MR Double rod, cap end -MR Double rod, both ends -MR2 PTFE seals -T Viton seals -V Quad seals -Q External guide, nonrotating for load guiding (See page.65) -G Hydraulic: Standard cover -H Thick cover -HHC Air service: Thick cover -HC /4 NPT ports -P4 Hole thru double rod shaft: 5 / 32 " hole -6 Plus size: /4" hole -25 50 psi max Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Sound limiters: Rod end -LF Cap end -LR Both ends -LFR Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable extend stroke -AS (Full stroke adjustment is standard) Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot -PM Ports to slot -SM Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.50,.52 See pages.3.5 for general option information and pages.49,.50 &.52 for option specifications of 2 /2" bore models..47 A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com 6-3-02
2-/2" (52) Bore Single Rod Standard Specifications X Double Acting 5/8 x. Wrench Flat.4 45 3.74 /2-20 x E 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. XK Double Acting Nonrotating 5/8 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4 45 3.74 /2-20 x E2 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. See page.6 for Mounting Bolts. Push area = 4.9 Pull area = 4.47 Seal Kits for Series: Original = 52-SK "T" = 52-SKG B K Y Z.9 /8 NPT s AB & AA are Ported on Opposite Sides Original Series See page.6 for Mounting Bolts. Push area = 4.7 Pull area = 4.27 Seal Kits for Series: Original = 52-SK-K "T" = 52-SKG-K B2 K2 Y2 Z2.38 /8 NPT s AB & AA are Ported on Opposite Sides "T" Series, Inches /8 /4 /2 3/4 /2 2 3 4 /4 /2 3/4 /4 3/4 2 3/4 3 3/4, Letter AB AA A B C D E F G TA TB TC TD TE TF TG X Double Acting X Double Acting B.45.58.83 2.20 2.33 2.83 3.33 4.33 5.33.83 2.20 2.33 2.83 3.33 4.33 5.33 E.56.63.63.88.88.88.88.88.88.63.88.88.88.88.88.88 K.05.8.43.80.93 2.43 2.93 3.93 4.93.43.80.93 2.43 2.93 3.93 4.93 Y.52.52.52.64.64.64.64.64.64.52.64.64.64.64.64.64 Z.89.02.27.64.77 2.27 2.77 3.77 4.77.27.64.77 2.27 2.77 3.77 4.77 Weight, lb..43.50.67 2.00 2.03 2.38 2.73 3.46 4.9.89 2.22 2.25 2.60 2.95 3.68 4.4 XK Double Acting, Nonrotating XK Double Acting, Nonrotating B2.64.77 2.02 2.39 2.52 3.02 3.52 4.52 5.52 2.02 2.39 2.52 3.02 3.52 4.52 5.52 E2.56.63.63.88.88.88.88.88.88.63.88.88.88.88.88.88 K2.24.37.62.99 2.2 2.62 3.2 4.2 5.2.62.99 2.2 2.62 3.2 4.2 5.2 Y2.52.52.52.64.64.64.64.64.64.52.64.64.64.64.64.64 Z2.89.02.27.64.77 2.27 2.77 3.77 4.77.27.64.77 2.27 2.77 3.77 4.77 Weight, lb..64.72.89 2.23 2.27 2.63 3.00 3.75 4.5 2. 2.45 2.50 2.85 3.22 4.00 4.73 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.45.58.83 2.20 2.33 4.33 NA* NA* NA*.83 2.20 2.33 4.33 NA* NA* NA* E3.56.63.63.88.88.88 NA* NA* NA*.63.88.88.88 NA* NA* NA* K3.05.3.43.80.93 3.93 NA* NA* NA*.43.80.93 3.93 NA* NA* NA* Y3 Vent.64 NA* NA* NA* Vent.64 NA* NA* NA* Z3.89.02.27.64.77 3.77 NA* NA* NA*.27.64.77 3.77 NA* NA* NA* Weight,. lb..38.46.62.94.96 3.60 NA* NA* NA*.84 2.6 2.8 3.82 NA* NA* NA* Preload, lb. 2.0 6.2 7.0 5.0 4.7 7.3 NA* NA* NA* 3. 0.6 8.0 9.5 NA* NA* NA* End of, lb. 8.0 8.0 20.0 5.5 20.0 20.0 NA* NA* NA* 20.0 5.5 20.0 20.0 NA* NA* NA* OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4 2.02 2.27 2.77 3.39 3.77 NA* NA* NA* NA* 2.52 3.4 3.52 NA* NA* NA* NA* E4.56.63.63.88.88 NA* NA* NA* NA*.63.88.88 NA* NA* NA* NA* K4.49.62.87 2.24 2.37 NA* NA* NA* NA*.87 2.24 2.37 NA* NA* NA* NA* Y4.65.77.02.40.64 NA* NA* NA* NA*.77.4.39 NA* NA* NA* NA* Z4.02.27.77 2.39 2.77 NA* NA* NA* NA*.52 2.4 2.52 NA* NA* NA* NA* Weight, lb..9.98 2.6 2.49 2.5 NA* NA* NA* NA* 2.38 2.7 2.73 NA* NA* NA* NA* Preload, lb. 6.2 2.5 5.5 5.0 5.2 NA* NA* NA* NA*.2 2.4 0.2 NA* NA* NA* NA* End of, lb. 2.0 2.0 8.5 5.5 20.5 NA* NA* NA* NA* 8.5 2. 22.6 NA* NA* NA* NA* O Single Acting 5/8 x. Spring Retracted Wrench Flat.75 Rod Dia. See page.6 for Mounting Bolts. Push area = 4.9 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 52-SK "T" = 52-SKG 2-4-08 Rod End Face B3.4 K3 /8 NPT 45 3.74 /2-20 x E3 Y3 Z3 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.7 Rod End Vent s AB-C & TA - TC Rod End Vent s D & TD.9 OP Single Acting Spring Extended See page.6 for Mounting Bolts. Pull area = 4.47 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 52-SK "T" = 52-SKG 5/8 x. Wrench Flat B4.4 + K4 45 3.74 Y4 /2-20 x E4 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. Z4.63 /8 NPT s AB & AA are Ported on Opposite Sides NA* = Not Available.48
2-/2" (52) Bore Also See Page.48 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread 63.5mm Bore Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.7. Original Series mm 3.2 6.4 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AB AA A B C D E F G T Series mm 6.4 2.7 9. 3.8 44.5 69.9 95.3 Letter TA TB TC TD TE TF TG Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 4 Places for M6 SHCS Thread Pitches M6 =.0mm M2 =.75mm Conversion Factor Inches x 25.4 = mm M2 x 25.4 82.5mm Bolt Circle Standard Female Rod Thread M2. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original and T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.48. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 -X -XK NA NA NA -O NA NA NA NA NA NA -OP NA NA NA Suffix Options -PM & -SM Clevis Mount Available On Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3. Chart Also see page.48 Chart Dimension -X, -O, -OP.9 + B -XK.00 + B.50.90 Note.97.50.63.86 Oil filled bushings Note : Hole Diameter =.50 Pin Diameter =.500 Pin (46 Stainless Steel) and Clips are included. -PM Port Location IN LINE with Slot -SM Port Location to Slot RC-Chart Rod Clevis and Pin Threaded Stud mates with Female Rod thread in the Pancake Cylinders. Slot and Pin Mate with EM-2 Eye Bracket shown below. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.32.3.69.2.63. 6.00 CHART /2-20 x Thread Length Metric M2 x Thread Length Rod Clevis Number RC-54 RC-56 MRC-54 MRC-56 s AB AA G MAB MAA MG Pin Diameter.325 Thread Length.39".62" 9.9mm 5.7mm EM-52 Eye Bracket Kit Mates with Clevis Mount shown above. Order separately..75.3 EM-2 Eye Bracket Kit Mates with any Rod Clevis shown above. Order separately..44.69.38 2.00.3.50.33 Dia. 4 Places for Flat Head Screws Four 5/6-8 x " FHSCS are included Material: Zinc Die Casting.38.50 2.00 2.25.47.38 Hole.50 Oil filled bushing is standard.27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.3.94.50.38.30.25 Hole.335 Oil filled bushing is standard.49 2-5-04
2-/2" (52) Bore Also See Page.48 Option Specifications Suffix Option -HHC Hydraulic & -HC Air Available on Original and T Series with -X, -O. Also see Option Information on page.9 for Pressure and Mounting details..9 + B.9 + K.38 Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK, -O, -OP. /2-20 x.00 Also see Option Information on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.. /6 Hex Nut Adjusting Screw.050 Adjustment Per Revolution.9 s " & Shorter =.50 Max. + s " & Longer =.38 + Adjustment.9 + B Standard Adjustment is " (-XK only use B2 as shown on page.48. No additional length is required.) (-OP Only use B4 as shown on page.48. No additional length is required.) Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 2 /2" (52) Bore Quick Reference to Standard s Use the appropriate Letter in the Model Number /4" 60 Dovetail Profile of Sensor & Mounting Slot. Sensors available for AA & TA strokes and longer. AA is ported on opposite sides. 45 #2 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Available on Original Series X, XK /4------------------AA /2-------------------A 3/4-------------------B -------------------- C /2--------------- D 2---------------------E 3---------------------F 4-------------------- G Available on T Series X, XK /4-----------------TA /2-----------------TB 3/4-----------------TC /4---------------TD 3/4---------------TE 2 3/4---------------TF 3 3/4-------------- TG Suffix Option -AS Adjustable Extend Available on Original Series with s: -X, -XK, -O Also see Option Information on page.. BB D C E Inches /8 /4 /2 3/4 -/2 2 3 4 Letter AB AA A B C D E F G s: -X, -XK BB 2.02 2.4 2.39 2.77 2.89 3.39 3.89 4.89 5.89 s:-o BB 2.02 2.4 2.39 2.77 2.89 4.89 NA NA NA C.67.9 2.4 2.9 3.4 4.4 5.4 7.4 9.4 D 0.63 0.75.00.25.50 2.00 2.50 3.50 4.50 E 0.88.00.25.50.75 2.25 2.75 3.75 4.75.50 Dia. 2.00 Dia..063 Adjustment Per Revolution 2-5-08.50
Pancake Cylinders XDR Original Series Double Rod, Double Acting See page.6 for Mounting Bolts Force Area = 4.47 Seal Kit = 52-SK 2-/2" (52) Bore Double Rod, Inches /8 /4 /2 3/4 -/2 2 3 4, Letter AB AA A B C D E F G B 2.02 2.4 2.39 2.77 2.89 3.39 3.89 4.89 5.89 E.56.63.63.88.88.88.88.88.88 K.63.75 2.00 2.38 2.50 3.00 3.50 4.50 5.50 Y.52.52.52.64.64.64.64.64.64 Z.89.02.27.64.77 2.27 2.77 3.77 4.77 Weight, lb. 2.20 2.29 2.48 2.82 2.83 3.28 3.67 4.60 5.40 Standard Specifications 5/8 x. Wrench Flat B.4 K.4 + 45 3.74 /2-20 x E 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. /8 NPT s AB & AA are Ported on Opposite Sides Y Z.75 XDRK Original Series Double Rod, Double Acting, Nonrotating See page.6 for Mounting Bolts Force Area = 4.27 Seal Kit = 52-SK-K, Inches /8 /4 /2 3/4 -/2 2 3 4, Letter AB AA A B C D E F G B 2.02 2.4 2.39 2.77 2.89 3.39 3.89 4.89 5.89 E.56.63.63.88.88.88.88.88.88 K.63.75 2.00 2.38 2.50 3.00 3.50 4.50 5.50 Y.52.52.52.64.64.64.64.64.64 Z.89.02.27.64.77 2.27 2.77 3.77 4.77 Weight, lb. 2.34 2.43 2.63 2.97 2.99 3.45 3.85 4.79 5.62 5/8 x. Wrench Flat Random Rotation Rod Rotation Tolerance ± B.4 K.4 + 45 3.74 /2-20 x E 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. /8 NPT s AB & AA are Ported on Opposite Sides Y Z.75 ODR Original Series Double Rod, Single Acting, Spring Retracted See page.6 for Mounting Bolts Force Area = 4.47 Seal Kit = 52-SK, Inches /8 /4 /2 3/4 -/2, Letter AB AA A B C D B 2.02 2.4 2.39 2.77 2.89 4.89 E.56.63.63.88.88.88 K.63.75 2.00 2.38 2.50 4.50 Y Vent.64 Z.89.02.27.64.77 3.77 Weight, lb. 2.4 2.23 2.4 2.76 2.77 4.52 Spring Return Forces, lb. Preload 2.0 6.3 7.0 5.0 4.8 7.3 End of 8.0 8.0 20.0 5.5 20.0 20.0 5/8 x. Wrench Flat.7 Rod End Vent s AB C B /8 NPT.4 K.4 + 45 3.74 /2-20 x E 3.25 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. Rod End Vent D Y Z.75.5 4-22-04
2-/2" (52) Bore Also See Page.5 Prefix Option -M Metric Cylinder & Rod Thread, 63.5mm Bore Available on Original Series with s: -XDR, -XDRK, -ODR Also see Option Information on page.7. mm 3.2 6.4 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AB AA A B C D E F G Option Specifications Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 4 Places for M6 SHCS Thread Pitches M6 =.0mm M2 =.75mm Conversion Factor Inches x 25.4 = mm M2 x 25.4 82.5mm Bolt Circle Standard Female Rod Thread M2. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.5. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 6 25 -XDR - XDRK NA NA NA -ODR NA NA NA NA NA NA Suffix Options -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use MR For Cap End only use MR For Both Ends use MR2 Also see Option Information on Page.8. /2-20 x.00 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 /4" 60 Dovetail Profile of Sensor & Mounting Slot. 2 /2" (52) Bore Quick Reference to Standard s Use the appropriate Letter in the Model Number Sensors available for AA strokes and longer. AA is ported on opposite sides. #2 45 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Available on Original Series XDR, XDRK /4------------------AA /2-------------------A 3/4-------------------B -------------------- C /2--------------- D 2---------------------E 3---------------------F 4-------------------- G 2-5-08.52
3" (72) Bore Model Number Model Number Code Prefix Options Leave blank if none desired Suffix Options C 72 X MR Metric M See pages.7,.55 &.58 Bore Code 3" 72 76.2mm 72 Standard s Original Series X XK XDR O XDRK ODR OP /8 AB AB AB /4 AA AA AA /2 A A A 3/4 B B B C C C /2 D D 2 E 3 F 4 G T Series Includes PTFE piston bearing X XK O OP /4 TA TA TA /2 TB TB TB 3/4 TC TC TC /4 TD TD 3/4 TE 2 3/4 TF 3 3/4 TG Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E Single rod Double acting -X Double acting, Nonrotating Internal guide pins - 50 psi max -XK Single acting, spring retracted -O Single acting, spring extended -OP Double rod Double acting -XDR Double acting, Nonrotating Internal guide pins - 50 psi max -XDRK Single acting, spring retracted -ODR See pages.5 &.6 for Information. See pages.54 &.57 for Standard Specifications How to order. Under select letter(s) for desired Series and. 2. Under Bore select 72 for 3" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 3 / 4 "---------------- 7------------------.23 / 8 "------------2----------------.29 5 / 8 "------------22----------------.35 2"----------------32----------------.4 2 / 2 "------------52----------------.47 4"---------------22---------------.59 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES A-72-X Original Series, /2" stroke - 3" Bore - Single Rod, Double Acting TC-72-X-MR T Series, 3/4" - 3" Bore - Single Rod, Double Acting - Male Rod Thread Suffix Options Male rod thread: Single rod -MR Double rod, rod end -MR Double rod, cap end -MR Double rod, both ends -MR2 PTFE seals -T Viton seals -V Quad seals -Q External guide, nonrotating for load guiding (See page.65) -G Hydraulic: Standard cover -H Thick cover -HHC Air service: Thick cover -HC /4 NPT ports -P4 Hole thru double rod shaft: 5 / 32 " hole -6 Plus size: / 4 " hole -25 50 psi max Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Sound limiters: Rod end -LF Cap end -LR Both ends -LFR Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable extend stroke -AS (Full stroke adjustment is standard) Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot -PM Ports to slot -SM Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.56,.58 See pages.3.5 for general option information and pages.55,.56 &.58 for option specifications of 3" bore models..53 A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com 6-3-02
3" (72) Bore Single Rod Standard Specifications X Double Acting 5/8 x. Wrench Flat Rod End Face.4 45 4.24 /2-20 x E 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. XK Double Acting Nonrotating 5/8 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4 45 4.24 /2-20 x E2 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. See page.6 for Mounting Bolts. Push area = 7.07 Pull area = 6.63 Seal Kits for Series: Original = 72-SK "T" = 72-SKG Y Z B K.9 /8 NPT s AB & AA are Ported on Opposite Sides See page.6 for Mounting Bolts. Push area = 6.87 Pull area = 6.43 Seal Kits for Series: Original = 72-SK-K "T" = 72-SKG-K Y2 Z2 B2 K2.38 /8 NPT s AB & AA are Ported on Opposite Sides Original Series "T" Series, Inches /8 /4 /2 3/4 /2 2 3 4 /4 /2 3/4 /4 3/4 2 3/4 3 3/4, Letter AB AA A B C D E F G TA TB TC TD TE TF TG X Double Acting X Double Acting B.52.64.89 2.4 2.39 2.89 3.39 4.39 5.39.89 2.4 2.39 2.89 3.39 4.39 5.39 E.63.63.63.88.88.88.88.88.88.63.88.88.88.88.88.88 K.2.24.49.74.99 2.49 2.99 3.99 4.99.49.74.99 2.49 2.99 3.99 4.99 Y.52.52.52.64.64.64.64.64.64.52.64.64.64.64.64.64 Z.95.08.33.58.83 2.33 2.83 3.83 4.83.33.58.83 2.33 2.83 3.83 4.83 Weight, lb..89.97 2.8 2.36 2.57 2.98 3.28 4.22 5.03 2.49 2.68 2.89 3.30 3.70 4.54 5.40 XK Double Acting, Nonrotating XK Double Acting, Nonrotating B2.7.83 2.08 2.33 2.58 3.08 3.58 4.58 5.58 2.08 2.33 2.58 3.08 3.58 4.58 5.58 E2.63.63.63.88.88.88.88.88.88.63.88.88.88.88.88.88 K2.3.43.68.93 2.8 2.68 3.8 4.8 5.8.68.93 2.8 2.68 3.8 4.8 5.8 Y2.52.52.52.64.64.64.64.64.64.52.64.64.64.64.64.64 Z2.95.08.33.58.83 2.33 2.83 3.83 4.83.33.58.83 2.33 2.83 3.83 4.83 Weight, lb. 2.5 2.24 2.45 2.64 2.86 3.28 3.59 4.56 5.40 2.77 2.96 3.8 3.60 3.9 4.88 5.72 O Single Acting, Spring Retracted O Single Acting, Spring Retracted B3.52.64.89 2.4 2.39 4.39 NA* NA* NA*.89 2.4 2.39 4.39 NA* NA* NA* E3.63.63.63.88.88.88 NA* NA* NA*.63.88.88.88 NA* NA* NA* K3.2.24.49.74.99 3.99 NA* NA* NA*.49.74.99 3.99 NA* NA* NA* Y3 Vent.64 NA* NA* NA* Vent.64 NA* NA* NA* Z3.95.08.33.58.83 3.83 NA* NA* NA.33.58.83 3.83 NA* NA* NA* Weight,. lb..20.92 2. 2.29 2.5 4.36 NA* NA* NA* 2.43 2.6 2.83 4.68 NA* NA* NA* Preload, lb. 2.0 2.0 6.5 5.0 4.7 7.3 NA* NA* NA*.7 0.6 7.9 9.5 NA* NA* NA* End of, lb. 8.0 8.5 5.5 5.5 20.0 20.0 NA* NA* NA* 7.0 9.3 20.0 20.0 NA* NA* NA* OP Single Acting, Spring Extended OP Single Acting, Spring Extended B4 2.08 2.33 2.83 3.33 3.83 NA* NA* NA* NA* 2.58 3.08 3.58 NA* NA* NA* NA* E4.63.63.63.88.88 NA* NA* NA* NA*.63.88.88 NA* NA* NA* NA* K4.55.68.93 2.8 2.43 NA* NA* NA* NA*.93 2.8 2.43 NA* NA* NA* NA* Y4.65.77.02.39.64 NA* NA* NA* NA*.77.4.39 NA* NA* NA* NA* Z4.08.33.83 2.33 2.83 NA* NA* NA* NA*.58 2.08 2.58 NA* NA* NA* NA* Weight, lb. 2.49 2.60 2.69 2.99 3.20 NA* NA* NA* NA* 3.0 3.3 3.52 NA* NA* NA* NA* Preload, lb. 6.2 2.0 6.5 5.0 5.2 NA* NA* NA* NA*.7 0.6 8.5 NA* NA* NA* NA* End of, lb. 2.0 8.5 5.5 5.5 20.5 NA* NA* NA* NA* 7. 9.3 20.8 NA* NA* NA* NA* O Single Acting 5/8 x. Spring Retracted Wrench Flat.75 Rod Dia. See page.6 for Mounting Bolts. Push area = 7.07 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 72-SK "T" = 72-SKG 2-8-08 Rod End Face B3.4 K3 /8 NPT 45 4.24 /2-20 x E3 Y3 Z3 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.7 Rod End Vent s AB-C & TA - TC Rod End Vent s D & TD.9 OP Single Acting Spring Extended See page.6 for Mounting Bolts. Pull area = 6.63 See Chart for Spring Forces: Preload & End of Seal Kits for Series: Original = 72-SK "T" = 72-SKG 5/8 x. Wrench Flat B4.4 + K4 45 4.24 /2-20 x E4 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. Y4 Z4 /8 NPT s AB & AA are Ported on Opposite Sides NA* = Not Available.63.54
3" (72) Bore Also See Page.54 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread 76.2mm Bore Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.7. Original Series mm 3.2 6.4 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AB AA A B C D E F G T Series mm 6.4 2.7 9. 3.8 44.5 69.9 95.3 Letter TA TB TC TD TE TF TG Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 4 Places for M6 SHCS Thread Pitches M6 =.0mm M2 =.75mm Conversion Factor Inches x 25.4 = mm M2 x 25.4 96.8mm Bolt Circle Standard Female Rod Thread M2. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original and T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.54. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 -X -XK NA NA NA -O NA NA NA NA NA NA -OP NA NA NA Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.3. Chart Also see page.54 Chart Dimension -X, -O, -OP.9 + B -XK.00 + B.50.90 Note.97 Note : Hole Diameter =.50 Pin Diameter =.500 Pin (46 Stainless Steel) and Clips are included. -PM Port Location IN LINE with Slot -SM Port Location to Slot EM-52 Eye Bracket Kit Mates with Clevis Mount shown on the left. Order separately..33 Dia. 4 Places for Flat Head Screws Four 5/6-8 x " FHSCS are included Material: Zinc Die Casting.38 2.00.75.38.47.38 2.00.50 2.25 Hole.50 Oil filled bushing is standard.3.50.63.86 Oil filled bushings RC-56 Rod Clevis and Pin Threaded Stud mates with Female Rod thread in the Pancake Cylinders. Slot and Pin Mate with EM-2 Eye Bracket shown on the right. Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 Stainless Steel Pin & Clips are included.32.3.69.2.63. 6.00 Pin Diameter.325 /2-20 x.62 Optional Metric #MRC-56 M2 x 5.7 EM-2 Eye Bracket Kit Mates with RC-56 Rod Clevis shown on the left. Order separately..27 Dia. 4 Places for Flat Head Screws Four /4-20 x 3/4" FH(#2)M Screws are included Material: Zinc Die Casting.44.3.3.94.50.38.30.25.50 Hole.335 Oil filled bushing is standard.69.55 2-5-04
3" (72) Bore Also See Page.54 Option Specifications Suffix Option -HHC Hydraulic & -HC Air Available on Original and T Series with -X, -O. Also see Option Information on page.9 for Pressure and Mounting details..9 + B.9 + K.38 Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK, -O, -OP. Also see Option Information /2-20 x.00 on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK, -O, -OP Also see Option Information on page.. /6 Hex Nut Adjusting Screw.050 Adjustment Per Revolution.9 s " & Shorter =.50 Max. + s " & Longer =.38 + Adjustment.9 + B Standard Adjustment is " (-XK Only use B2 as shown on page.54. No additional length is required.) (-OP Only use B4 as shown on page.54. No additional length is required.) Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 /4" 60 Dovetail Profile of Sensor & Mounting Slot. 3" (72) Bore Sensors available for AA & TA strokes and longer. AA is ported on opposite sides. 45 30 30 #2 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series X, XK /4-------------------AA /2--------------------A 3/4--------------------B --------------------- C /2---------------- D 2----------------------E 3----------------------F 4--------------------- G Available on T Series X, XK /4-----------------TA /2-----------------TB 3/4-----------------TC /4---------------TD 3/4---------------TE 2 3/4---------------TF 3 3/4-------------- TG Suffix Option -AS Adjustable Extend Available on Original Series with s: -X, -XK, -O Also see Option Information on page.. BB D C E Inches /8 /4 /2 3/4 -/2 2 3 4 Letter AB AA A B C D E F G s: -X, -XK BB 2.08 2.20 2.45 2.70 2.95 3.45 3.95 4.95 5.95 s:-o BB 2.08 2.20 2.45 2.70 2.95 4.95 NA NA NA C.67.9 2.4 2.9 3.4 4.4 5.4 7.4 9.4 D 0.63 0.75.00.25.50 2.00 2.50 3.50 4.50 E 0.88.00.25.50.75 2.25 2.75 3.75 4.75.50 Dia. 2.00 Dia..063 Adjustment Per Revolution 2-5-08.56
3" (72) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting See page.6 for Mounting Bolts Force Area = 6.63 Seal Kit = 72-SK, Inches /8 /4 /2 3/4 -/2 2 3 4, Letter AB AA A B C D E F G B 2.08 2.20 2.45 2.70 2.95 3.45 3.95 4.95 5.95 E.63.63.63.88.88.88.88.88.88 K.68.80 2.0 2.30 2.55 3.0 3.55 4.55 5.55 Y.52.52.52.64.64.64.64.64.64 Z.95.08.33.58.83 2.33 2.83 3.83 4.83 Weight, lb. 2.84 2.95 3.6 3.39 3.6 4.09 4.53 5.50 6.47 5/8 x. Wrench Flat Rod End Face B.4 K.4 + 45 4.24 /2-20 x E 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. /8 NPT s AB & AA are Ported on Opposite Sides Y Z.75 XDRK Original Series Double Rod, Double Acting, Nonrotating See page.6 for Mounting Bolts Force Area = 6.43 Seal Kit = 72-SK-K, Inches /8 /4 /2 3/4 -/2 2 3 4, Letter AB AA A B C D E F G B 2.08 2.20 2.45 2.70 2.95 3.45 3.95 4.95 5.95 E.63.63.63.88.88.88.88.88.88 K.68.80 2.0 2.30 2.55 3.0 3.55 4.55 5.55 Y.52.52.52.64.64.64.64.64.64 Z.95.08.33.58.83 2.33 2.83 3.83 4.83 Weight, lb. 3.0 3.2 3.43 3.67 3.90 4.39 4.84 5.84 6.84 5/8 x. Wrench Flat Random Rotation Rod Rotation Tolerance ±.4 B K.4 + 45 4.24 /2-20 x E 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. /8 NPT s AB & AA are Ported on Opposite Sides Y Z.75.57 ODR Original Series Double Rod, Single Acting, Spring Retracted See page.6 for Mounting Bolts Force Area = 6.63 Seal Kit = 72-SK, Inches /8 /4 /2 3/4 -/2, Letter AB AA A B C D B 2.08 2.20 2.45 2.70 2.95 4.95 E.63.63.63.88.88.88 K.68.80 2.0 2.30 2.55 4.55 Y Vent.64 Z.95.08.33.58.83 3.83 Weight, lb. 2.77 2.88 3.0 3.3 3.54 5.64 Spring Return Forces, lb. Preload 2.0 2.0 6.5 5.0 4.7 7.3 End of 8.0 8.5 5.5 5.5 20.0 20.0 5/8 x. Wrench Flat.7 Rod End Vent s AB C.4 B /8 NPT K.4 + 45 4.24 /2-20 x E 3.8 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.75 Rod Dia. Y Z.7 Rod End Vent D.75 0-23-04
3" (72) Bore Also See Page.57 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread, 76.2mm Bore Available on Original Series with s: -XDR, -XDRK, -ODR Also see Option Information on page.7. mm 3.2 6.4 2.7 9. 25.4 38. 50.8 76.2 0.6 Letter AB AA A B C D E F G Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 4 Places for M6 SHCS Thread Pitches M6 =.0mm M2 =.75mm Conversion Factor Inches x 25.4 = mm 96.8mm Bolt Circle Standard Female Rod Thread M2. Male Rod Thread Option -MR shown. M2 x 25.4 G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.57. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 6 25 -XDR -XDRK NA NA NA -ODR NA NA NA NA NA NA Suffix Options -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK, -ODR. For Rod End only use MR For Cap End only use MR For Both Ends MR2 Also see Option Information on Page.8 /2-20 x.00 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 /4" 60 Dovetail Profile of Sensor & Mounting Slot. 3" (72) Bore Quick Reference to Standard s Use the appropriate Letter in the Model Number Sensors available for AA strokes and longer. AA is ported on opposite sides. Available on Original Series 45 30 30 #2 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only XDR, XDRK /4-------------------AA /2--------------------A 3/4--------------------B --------------------- C /2---------------- D 2----------------------E 3----------------------F 4--------------------- G 2-5-08.58
4" (22) Bore Model Number Model Number Code Prefix Options Bore Leave blank if none desired Suffix Options D 22 X MR Metric M See pages.7,.6 &.64 Bore Code 4" 22 0.6mm 22 Standard s Original Series X XK XDR XDRK /8 AC /4 AB /2 AA A /2 B 2 C 3 D 4 E T Series Includes PTFE piston bearing X XK 5/6 TAA 3/6 TA 5/6 TB 3/6 TC 2 3/6 TD 3 3/6 TE Grey shading indicates sensors are not available. s are NOT affected by magnetic piston Option E Single rod How to order. Under select letter(s) for desired Series and. 2. Under Bore select 22 for 4" bore. Seven Other Bore Sizes are Available Bore Bore Code See page / 2 "---------------- 5------------------.7 3 / 4 "---------------- 7------------------.23 / 8 "------------2----------------.29 5 / 8 "------------22----------------.35 2"----------------32----------------.4 2 / 2 "------------52----------------.47 3"----------------72----------------.53 3. Under select letter(s) for desired action. 4. Under Prefix & Suffix Options select letter(s) for desired options and add to model number. EXAMPLES Double acting -X Double acting, Nonrotating Internal guide pins - 50 psi max Double rod Double acting Double acting, Nonrotating Internal guide pins - 50 psi max D-22-X Original Series, 3" stroke - 4" Bore - Single Rod, Double Acting -XK -XDR -XDRK See pages.5 &.6 for Information. See pages.60 &.63 for Standard Specifications TD-22-X-MR T Series, 2 3/6" - 4" Bore - Single Rod, Double Acting - Male Rod Thread Suffix Options Male rod thread: Single rod -MR Double rod, rod end -MR Double rod, cap end -MR Double rod, both ends -MR2 PTFE seals -T Viton seals -V Quad seals -Q External guide, nonrotating for load guiding (See page.65) -G Hydraulic: Standard cover -H Thick cover -HHC Air service: Thick cover -HC /4 NPT ports -P4 Hole thru double rod shaft: / 4 " hole 50 psi max -25 Finish: ProCoat (Electroless Nickel) -N collar: /8" -C /4" -C2 3/8" -C3 /2" -C4 5/8" -C5 3/4" -C6 7/8" -C7 Sound limiters: Rod end -LF Cap end -LR Both ends -LFR Rubber Bumpers: Rod end -BF Cap end -BR Both ends -BFR Adjustable extend stroke -AS (Full stroke adjustment is standard) Adjustable retract stroke (Over " adjustment add desired length, e.g. -RS2) -RS Clevis mount: Ports in-line with slot -PM Ports to slot -SM Magnetic piston & sensor mounting slot(s) -E Order sensors separately. See page.4. length determines number of mounting slots. See page.4,.62,.64 See pages.3.5 for general option information and pages.6,.62 &.64 for option specifications of 4" bore models. A complete library of cylinder CAD drawings is available from your local Fabco-Air Distributor or from the Fabco-Air web site http://www.fabco-air.com.59 6-3-02
4" (22) Bore Single Rod Standard Specifications X Double Acting 3/4 x.7 Wrench Flat B.20 K 45 5.50 See page.6 for Mounting Bolts. Push area = 2.57 Pull area =.97 Seal Kits for Series: Original = 22-SK "T" = 22-SKG 5/8-8 x E 5.00 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced Y Z.88 Rod Dia..3 XK Double Acting Nonrotating 3/4 x.7 Wrench Flat Random Rotation Rod Rotation Tolerance ± B2.20 K2 45 5.50 See page.6 for Mounting Bolts. Push area = 2.47 Pull area =.87 Seal Kits for Series: Original = 22-SK-K "T" = 22-SKG-K 5/8-8 x E2 5.00 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced Y2 Z2.88 Rod Dia..50 /8 NPT /8 NPT Original Series "T" Series, Inches /8 /4 /2 /2 2 3 4 5/6 3/6 5/6 3/6 2 3/6 3 3/6, Letter AC AB AA A B C D E TAA TA TB TC TD TE X Double Acting X Double Acting B.89 2.02 2.27 2.77 3.27 3.77 4.77 5.77 2.27 2.77 3.27 3.77 4.77 5.77 E.50.50.75.88.88.88.88.88.75.88.88.88.88.88 K.43.56.8 2.3 2.8 3.3 4.3 5.3.8 2.3 2.8 3.3 4.3 5.3 Y.58.58.70.70.70.70.70.70.70.70.70.70.70.70 Z.20.33.58 2.08 2.58 3.08 4.08 5.08.58 2.08 2.58 3.08 4.08 5.08 Weight, lb. 3.88 4.0 4.34 4.9 5.63 6.22 7.53 8.84 5.04 5.6 6.33 6.92 8.23 9.54 XK Double Acting, Nonrotating XK Double Acting, Nonrotating B2 2.08 2.2 2.46 2.96 3.46 3.96 4.96 5.96 2.46 2.96 3.46 3.96 4.96 5.96 E2.50.50.75.88.88.88.88.88.75.88.88.88.88.88 K2.62.75 2.00 2.50 3.00 3.50 4.50 5.50 2.00 2.50 3.00 3.50 4.50 5.50 Y2.58.58.70.70.70.70.70.70.70.70.70.70.70.70 Z2.20.33.58 2.08 2.58 3.08 4.08 5.08.58 2.08 2.58 3.08 4.08 5.08 Weight, lb. 4.3 4.44 4.78 5.36 6.0 6.70 8.04 9.38 5.48 6.06 6.80 7.50 8.74 0.08 4-22-04.60
4" (22) Bore Also See Page.60 Option Specifications Prefix Option -M Metric Cylinder & Rod Thread 0.6mm Bore Available on Original and T Series with s: -X, -XK Also see Option Information on page.7. Original Series mm 3.2 6.4 2.7 25.4 38. 50.8 76.2 0.6 Letter AC AB AA A B C D E T Series mm 7.9 20.6 33.3 46.0 7.4 96.7 Letter TAA TA TB TC TD TE Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 4 Places for M6 SHCS Thread Pitches M6 =.0mm M6 = 2.0mm Conversion Factor Inches x 25.4 = mm M6 x 3.8 27.0mm Bolt Circle Standard Female Rod Thread M6. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original and T Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.60. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 -X -XK NA Suffix Options -PM & -SM Clevis Mount Available on Original and T Series with s: -X, -XK Also see Option Information on page.3. EM-22 Eye Bracket Kit Mates with Clevis Mount shown on the left. Order separately..44 + B Also see page.60.63.06 Note : Hole Diameter =.626 Pin Diameter =.625 Pin (46 Stainless Steel) and Clips are included..34 Dia. 4 Places for Flat Head Screws Four 5/6-8 x " FHSCS are included.75.00 2.50.0 Note.22.63 2.00 2.24 -PM Port Location IN LINE with Slot -SM Port Location to Slot Material: Zinc Die Casting.50 2.25.58.38.63 2.63 Hole.626 Oil filled bushing is standard Oil filled bushings RC-63 Rod Clevis and Pin Threaded Stud mates with Female Rod thread in the Pancake Cylinders. Slot and Pin Mate with EM-52 Eye Bracket shown on the right. EM-52 Eye Bracket Kit Mates with RC-63 Rod Clevis shown on the left. Order separately..75.3 Materials: Clevis Steel, Black Oxide Stud Steel Pin 46 StainlessSteel Pin & Clips are included.50 2.3.63 Pin Diameter.500.62.94. 80.38 5/8-8 x.75 Optional Metric #MRC-63 M6 x 9.0.33 Dia. 4 Places for Flat Head Screws Four 5/6-8 x " FHSCS are included Material: Zinc Die Casting.38 2.00.38.47.38 2.00.50 2.25 Hole.50 Oil filled bushing is standard.6 2-5-04
4" (22) Bore Also See Page.60 Option Specifications Suffix Option -MR Male Rod Thread Available on Original and T Series with s: -X, -XK 5/8-8 x.25 Also see Option Information on page.8. Suffix Option -RS Adjustable Retract Available on Original and T Series with s: -X, -XK Also see Option Information on page.. Suffix Option -HHC Hydraulic & -HC Air Available on Original and T Series with -X. Also see Option Information on page.9. /6 Hex Nut Adjusting Screw.9 + B.9 + K.050 Adjustment Per Revolution.9 s " & Shorter =.38 Max. + s " & Longer =.38 + Adjustment.9 + B Standard Adjustment is " (-XK only use B2 as shown on page.60. No additional length is required.).50 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 4" (22) Bore Quick Reference to Standard s Use the appropriate Letter in the Model Number /4" 60 Dovetail Profile of Sensor & Mounting Slot. Sensors available for AB & TAA strokes and longer. 45 30 30 #2 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Available on Original Series X, XK /4-------------------AB /2-------------------AA ----------------------A -/2-----------------B 2--------------------- C 3--------------------- D 4----------------------E Available on T Series X, XK 5/6-----------------TAA 3/6----------------TA 5/6----------------TB -3/6-------------TC 2-3/6-------------TD 3-3/6-------------TE Suffix Option -AS Adjustable Extend Available on Original Series with s: -X, -XK Also see Option Information on page.. BB D C E 2.00 Dia. Inches /8 /4 /2 -/2 2 3 4 Letter AC AB AA A B C D E BB 2.33 2.45 2.70 3.20 3.70 4.20 5.20 6.20 C.66.9 2.4 3.4 4.4 5.4 7.4 9.4 D 0.63.75.00.50 2.00 2.50 3.50 4.50 E 0.88.00.25.75 2.25 2.75 3.75 4.75.063 Adjustment Per Revolution.50 Dia. 2-5-08.62
4" (22) Bore Double Rod Standard Specifications XDR Original Series Double Rod, Double Acting See page.6 for Mounting Bolts. Force area =.97 Seal Kit = 22-SK 3/4 x.7 Wrench Flat 5.50 5/8-8 x E 5.00 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.88 Rod Dia. 45, Inches /8 /4 /2 /2 2 3 4, Letter AC AB AA A B C D E B 2.33 2.45 2.70 3.20 3.70 4.20 5.20 6.20 E.50.50.75.88.88.88.88.88 K.87 2.00 2.25 2.75 3.25 3.75 4.75 5.75 Y.58.58.70.70.70.70.70.70 Z.20.33.58 2.08 2.58 3.08 4.08 5.08 Weight, lb. 5.22 5.38 5.75 6.44 7.6 7.72 9.9 0.3.20 B K /8 NPT.20 + Y Z.75 XDRK Original Series Double Rod, Double Acting, Nonrotating See page.6 for Mounting Bolts. Force area =.87 Seal Kit = 22-SK-K 3/4 x.7 Wrench Flat Random Rotation Rod Rotation Tolerance ±.20 45 5.50 5/8-8 x E 5.00 Bolt Circle.27 Dia. Thru.38 C'Bore x.26 Dp. for 4, /4" SHCS equally spaced.88 Rod Dia., Inches /8 /4 /2 /2 2 3 4, Letter AC AB AA A B C D E B 2.33 2.45 2.70 3.20 3.70 4.20 5.20 6.20 E.50.50.75.88.88.88.88.88 K.87 2.00 2.25 2.75 3.25 3.75 4.75 5.75 Y.58.58.70.70.70.70.70.70 Z.20.33.58 2.08 2.58 3.08 4.08 5.08 Weight, lb. 5.65 5.8 6.9 6.89 7.63 8.23 9.70 0.85 B K /8 NPT.20 + Y Z.75.63 2-4-08
4" (22) Bore Also See Page.63 Option Specifications Prefix Option M Metric Cylinder & Rod Thread 0.6mm Bore Available on Original Series with s -XDR, -XDRK. Also see Option Information on Page.7 mm 3.2 6.4 2.7 25.4 38. 50.8 76.2 0.6 Letter AC AB AA A B C D E Mounting Holes 6.7mm Diameter Thru 0.3mm C'Bore x 6.4mm Dp. 4 Places for M6 SHCS Thread Pitches M6 =.0mm M6 = 2.0mm Conversion Factor Inches x 25.4 = mm M6 x 3.8 27.0mm Bolt Circle Standard Female Rod Thread M6. Male Rod Thread Option -MR shown. G/8 Ports with 4mm Spotface The Suffix Options charted on the right are available on Original Series with the s indicated ( ). They require no dimensional changes from the Standard Specifications on page.63. Also see Option Information on pages.7 thru.5. T V Q H N C C7 LF LR LFR BF BR BFR P4 25 -XDR -XDRK NA Suffix Options -MR, -MR, -MR2 Male Rod Thread Available on Original Series with s -XDR, -XDRK. For Rod End only use MR For Cap End only use MR For Both Ends use MR2 Also see Option Information on Page.8 5/8-8 x.25 Suffix Option -E Specifies Magnetic Piston and Dovetail Mounting Slot(s) s are NOT affected by magnetic piston. Sensors Must be Ordered Separately See Sensor Models Available page.4 /4" 60 Dovetail Profile of Sensor & Mounting Slot. 4" (22) Bore Sensors available for AB strokes and longer. 45 30 30 #2 # Sensor Slots at Positions # and # 2 Sensor Slot at Position # only Quick Reference to Standard s Use the appropriate Letter in the Model Number Available on Original Series XDR, XDRK /4-------------------AB /2-------------------AA ----------------------A /2-----------------B 2--------------------- C 3--------------------- D 4----------------------E 2-5-08.64
External Guide Pins External Guide Pins Provide Load Guiding External guide pins, adapted to the Pancake cylinder line provide a superior nonrotating piston rod feature for applications such as package placement, figure stamping, and any application where antirotation and registration are critical as the piston is extended and retracted. A mounting block is bolted to the piston rod. This block has two square pins mounted to it which in turn pass through guide blocks mounted on the sides of the cylinder. Square guide pins are hard chrome plated steel for long wear and corrosion resistance. Guide blocks are hard anodized aluminum for long wear and corrosion resistance. Clearance in guide block mounting holes provide for adjustment and backlash control, compensation for wear, and minimal rotation. Extended distance between guides provides superior nonrotation and support. Extended piston rod provides clearance between cylinder and guide bar mounting block to eliminate pinch points. Model G-22-X-G Shown Available on Pancake cylinders: Original and "T" Series Bores: 3/4" (7), /8" (2), 5/8" (22), 2" (32), 2 /2" (52), 3" (72), and 4" (22) s: /8" through 4" s: X, XDR In combination with Options: Suffix; -T, -V, -Q, -H, HHC, -HC,-P4, -N, -C -C7, -AS, -RS, -LF, -LR, -LFR, -BF, -BR, -BFR, -E Also available in Square cylinders: Bores 3/4" through 2" s /8" through 6" See page 2.4 of this catalog. HOW TO ORDER Select the basic Pancake Cylinder model number for your desired series, bore and stroke. Then add -G as a Suffix Option. Please Note!! This option affects the rod end dimensions See details on page.66..65 4-9-04