E v a p o r a t o r s Ni Evaporator 11 to 96 Needles These systems have has a flow meter attached to the side for controlling the gas flow to the equalizer manifold giving equal gas flow to each well. Needle height is easily adjustable to enable most sizes and capacities of microplates Low cost solution for the concentration, 96 well versions available Each SS Needle delivers an equal flow of nitrogen or other gas. Gently speeds evaporation of excess liquid Gas flow: 1 to 100ml/needle Size: 7"w x 5 1/2"d x 7 1/2" h Body constructed of nylon and can be sterilized by autoclaving Catalog Number 99A EV11 Stand alone Evaporator 11 position with stand and flowmeter 099A EV15 Stand alone Evaporator 15 position with stand and flowmeter 099A EV20 Stand alone Evaporator 20 position with stand and flowmeter 099A EV24 Stand alone Evaporator 24 position with stand and flowmeter 099A EV48 Stand alone Evaporator 48 position with stand and flowmeter 099A EV8 Stand alone Evaporator 8 position for 40-60 ml tubes, with stand and flowmeter 099A EV96 Stand alone 96 well evaporator with stand and flowmeter
N i t r o g e n E v a p o r a t o r Low cost solution for the concentration 8 384 wells extractions and reactions Each SS Needle delivers an equal flow of nitrogen or other gas Gently speeds evaporation of excess liquid Heats to 100 C for even faster drying times. Digital temperature control. Gas flow: 1 to 100ml/needle Electrical Rating: 2.0A 50/60Hz Electrical: on/off power switch, fuse protection, 3 wire cord with molded plug Control Type: PID parameters with auto tune, 4 Digit LED display Accuracy: - 0.25% of span Size: 7"w x 5.1/2"d x 7 1/2"H Control Size: 5.1/2"w x 7 1/2"d x 2 1/4"h Body is constructed of nylon and can be sterilized by autoclaving Fine needle valve controls the total flow to the equalizer manifold that gives equal gas flow to each well. Each well has consistent evaporation. Needle height is easily adjustable to enable most sizes and capacities of microplates. Catalog Number Voltage Heated single block 20 well evaporator system for 15-16mm tubes, 099A EV2024STCE includes block, also heats manifold gas, 15ga needles Heated single block 24 well evaporator system for 12mm tubes, 099A EV2424STCE includes block, also heats manifold gas, 15 ga needles 384 well evaporator system, includes block and also heats manifold 099A EV38424STCE gas, 15ga needles Heated single block 8 well evpaorator system for 40-60 ml EPA vials, 099A EV824STCE includes block, also heats manifold gas, 15ga needles Heated single block 96 well evaporator system for standard well 099A EV9624STCE plates, also heats manifold gas, 15ga needles Aluminum Blocks Catalog Number R34 516 R34 561 R34 562 R34 563 Holds 8 EPA vials Holds 24 (15mm x 45mm) vials Holds 24 (12mm x 32mm) vials Holds 20 (15mm x 16mm) vials
F l e x i V a p L a b E v a p o r a t o r One manifold suits all standard size vials Easy closure of any manifold position Reduced nitrogen consumption Complete even flow rates to all ports Cost effective compared with existing models currently on the market They are low cost, small footprint instruments used to concentrate chemical and biochemical solutions for further analysis, or evaporate to dryness for further reactions. What makes this system unique is the ability to open or close each position by turning the knobs on the manifold. Catalog Number Voltage Notes 109A YH-1-24 FlexiVap Work Station with heating for small insert, 24 positions w/flow meter 240 1) 3.5 bar Does not include insert for vials, must be ordered separately 109A YH-1 FlexiVap Work Station, no heating for small insert, 24 position w/flow meter Non Heated 3.5 bar does not include insert for vials, must be ordered separately 109A YH-2 FlexiVap Work Station, no heating for larger insert, 48 positions w/flow meter Non Heated 1) 240 volt system come with the CEE/7 cord and CE compliant 3.5 bar does not include insert for vials, must be ordered separately Catalog Number 109A YH-2412 109A YH-2416 109A YH-2416-15 109A YH-2428 109A YH-2429-50 109A YH-4812 Aluminum insert block with 24 positions for up to 12mm vials (use with 109A YH-1, 109A YH-1-24 small systems) Aluminum insert block with 24 positions for 15mm to 16mm vials ( use with 109A YH-1, 109A YH-1-24 small systems) Aluminum insert block with 24 positions for 15ml Centrifuge tubes (use with 109A YH-1, 109A YH-1-24 small systems) Aluminum insert block with 12 positions for up to 28mm vials, EPA (use with 109A YH-1, 109A YH-1-24 small systems) Aluminum insert block with 12 positions for 50ml Centrifuge tubes (use with 109A YH-1, 109A YH-1-24 small systems) Large Aluminum insert block with 48 positions for up to 12mm vials (use with 109A YH-2) 109A YH-4815 Aluminum insert block with 48 positions for up to 15mm to 16mm vials (use with 109A YH-2) 109A YH-4816-15 109A YH-4828 109A YH-4829-50 Aluminum insert block with 48 positions for 15ml centrifuge tubes ( use with 109A YH-2) Aluminum insert block with 24 positions for up to 28mm vials, EPA (use with 109A YH-2 large systems) Aluminum insert block with 24 positions for 50ml Centrifuge tubes (use with 109A YH-2 large systems)
Vacuum manifold built on kit to retro fit onto our YH-1 and YH-2 systems for capture of solvent vapors. Catalog Number 109A VM-1-12 109A VM-1-24 109A VM-2-24 109A VM-2-48 Vacuum manifold bolt on kit for YH-1 systems, 12 positions Vacuum manifold bolt on kit for YH-1 systems, 24 positions Vacuum manifold bolt on kit for YH-2 systems, 24 positions Vacuum manifold bolt on kit for YH-2 systems, 48 positions F l e x i V a p w / V a c u u m M a n i f o l d The FlexiVap Work Station with Vacuum Manifold is the newest addition to our line of analytical nitrogen/air evaporators which allows for the capturing of solvent vapors. The key advantages are: One manifold suits many standard size vials for a totally sealed system Easy closure of any manifold position (Nitrogen flow) Reduced nitrogen consumption Complete even flow rates in all ports Vacuum gauge and regulator Cost effective compared with existing models on the market They are low cost, small footprint instruments used to concentrate chemical and biochemical solutions for further analysis, or evaporate to dryness for further reactions. What makes these systems unique is the ability to open or close each position by turning the manifold knobs and also the rack and pinion precision lab stand. Digital temperature control to 100 C is available on certain models. Catalog Number Voltage 109A YHV-1-1224 FlexiVap work station with heating for small insert, 12 positions with 109A YHV-1-2424 FlexiVap work station with heating for small insert, 24 positions with 109A YHV-2-2424 FlexiVap work station with heating for larger insert, 24 positions with 109A YHV-2-4824 FlexiVap work station with heating for larger insert, 48 positions with
Z i p v a p These systems are low cost, small footprint instruments used for solvent and water removal. All ZipVap evaporator systems come with aluminum chassis with on/off power switch, digital temperature control adjustable to 100 C, aluminum heatblock chamber, aluminum insert for specific vials/tubes, polypro manifold, flow meter and gas heat exchanger on select models. Standard IEC power inlet on back with 6 power cord. Dimensions: 9 w x 6-1/2 d x 5 t (top of heat block). Support rod that holds manifold is 7" long. The ZipVap has interchangeable aluminum insert and needle manifold and allow almost any laboratory size container to be adapted. Each spare aluminum insert and needle manifold has separate catalog numbers. Catalog Number Voltage 109A 11-80021CE 109A 11-80025CE 109A 11-80081CE 109A 11-80085CE 109A 11-80121CE 109A 11-80125CE 109A 11-80201CE 109A 11-80205CE 109A 11-80241CE 109A 11-80245CE 109A 11-80481CE 109A 11-80485CE 109A 11-80961CE 109A 11-80965CE 109A 11-83841CE 109A 11-83845CE Zipvap 2, 2position evaporator for 61 mm flask, insert heated only, gas inlet not Zipvap 2, 2 position evaporator for 61 mm flask, insert and gas inlet Zipvap 8, 8 position evaporator for 28 mm EPA vial, insert heated only, Zipvap 8, 8 position evaporator for 28 mm EPA vial, insert and gas inlet Zipvap 12, 12 position evaporator for 18 mm vial, insert heated only, Zipvap 12, 12 position evaporator for 18mm vial, insert and gas inlet Zipvap 20, 20 position evaporator for 15 mm vial, insert heated only, Zipvap 20, 20 position evaporator for 15 mm vial, insert and gas inlet Zipvap 24, 24 position evaporator for 15mm vial, insert heated only, Zipvap 24, 24 position evaporator for 15 mm vial, insert and gas inlet Zipzap 48, 48 position evaporator for 12mm auto sampler vial, insert heated only, Zipvap 48, 48 position evaporator for 12 mm auto sampler vial, insert and gas inlet Zipvap 96, 96 position evaporator for 96 well plate, insert heated only, Zipvap 96, 96 position for 96 well plate, insert and gas inlet heated, with flowmeter Zipvap 384, 384 position evaporator for 384 well plate, insert heated only, Zipvap 384, 384 position evaporator for 384 well plate, insert and gas inlet Pressure
T r i p l e Z i p v a p These systems are low cost, small footprint instruments used for solvent and water removal. All ZipVap evaporator systems come with aluminum chassis with on/off power switch, digital temperature control adjustable to 100 C, aluminum heat block chamber, polypro manifold with stainless steel needles, (3)flow meters with on/off switch and gas heat exchanger. Catalog Number Voltage 109A 11-80333CE Triple Position Evaporator for (3) 96 deep well plates, gas heater and flow meter with on/off switches included Pressure The ZipVap has also interchangeable aluminum insert and needle manifold and allow almost any laboratory size container to be adapted. Each spare aluminum insert and needle manifold has separate catalog numbers.
D i g i t a l P u l s e M i x e r H y b r i d E v a p o r a t o r This system is designed to rapidly evaporate/concentrate solvents by both heating the sample bottom and the incoming nitrogen and at the same time create a pulsing vortex mixing in the samples. Each pulse creates the vortex and the process continues until the concentration level is achieved. System flexibility is greatly increased with the availability of manifolds and blocks to fit your application. The Digital Pulse Mixer/Evaporator features: Micro-processor based control technology Speed 150 to 1,000 rpm, speed display resolution,.1 rpm, speed setting increment: 10rpm 4-line back-lit LCD display Built in digital timer (seconds: 1-60, minutes: 1-60, hours: 1-24) User selectable profile (pulses-per-minute: 1-1000), Ppm-duty-cycle: 1-99% Timer and pulse mode may be combined Communication port (USB) Membrane switch user interface (4-button) Soft start/stop of motor Optional software for real time data acquisition Orbital offset.070" Set point temperature for bottom blocks (120 C max.) Flow meter located on left side of mixer A fine needle valve for flow control is provided on each manifold imum psi: 20 Electrical: on/off switch, 3 wire 6 foot long cord Size: 12"w x 22"d x 8"h Drive plate: 7" x 12" Load capacity: imum 5 pounds Catalog Number Volts Watt 099A DPMES24CE Evap system 2 block format, without manifold 50/60Hz A PMAN96-96 well polypropylene manifold w/needles - 099A PMAN24-24 well polypropylene manifold w/needles - 099A PMAN20-20 well polypropylene manifold w/needles - 099A PMAN8-8 well polypropylene manifold w/needles - R34 562-24 well aluminum block 12mm vials - R34 561-24 well aluminum block 15mm vials - R34 563-20 well aluminum block 15 to 16mm vials - R34 516-8 well aluminum block for EPA vials -