INSTALLATION INSTRUCTIONS Accessory S Application 2011 PILOT Publications No. AII 43298 Issue Date MARCH 2010 PARTS LIST Back-up Sensor Attachment Kit P/N 08V67-SZA-100A Back-up sensor harness Fuse label Cushion tape Back-up sensor subharness 2 Flange nuts, 6 mm Switch Control unit Control unit bracket Switch bracket 14 Wire ties Small wire tie Harness tape Offset wire tie Clip 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 08V67-SZA-1000-91 1 of 16
Coupler clip Buzzer 4 Sensor clips Buzzer bracket Accessory User s Information Manual TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Small flat-tip screwdriver Shop towel Diagonal cutters Ratchet 8 mm, 10 mm, and 14 mm Sockets 10 mm Combination wrench Utility Knife T15 Torx Wrench Felt-tip pen Tape Pushpin Drill 3 mm Drill bit 24 mm and 26 mm Hole saws T/N AKS052507 Isopropyl alcohol Plastic Trim Tool T/N SILTRIMTL10 Eye protection Scissors Small rubber mallet Back-up Sensor Kit 2 Corner sensors 2 Center sensors (Larger) 2 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
Illustration of the Back-up Sensors Installed on the Vehicle 3. Remove the rear cargo tray (ten clips). CONTROL UNIT 10 S FUSE CASE (2 A) CORNER CENTER S (LARGER) INSTALLATION SUB CORNER 792407AE Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 4. Use a plastic trim tool to remove the cover (four retaining tabs). CARGO TRAY 700101BB CARGO AREA LIGHT CASE 2 BOLTS 1. Make sure you have the anti-theft code for the audio unit and the navigation system, then write down the radio presets. 2. Disconnect the negative cable from the battery. COVER 4 RETAINING TABS COVER PLASTIC TRIM TOOL 700102CB 5. Remove the two bolts from the rear cargo area light case. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 3 of 16
6. Release the seat belt from the rear upper trim and remove the rear upper trim (four clips and unplug the vehicle connector). 10. Using a small flat-tip screwdriver, push and release the seat belt lower hook from each third row seat. Insert the seat belt lower hook to the fix hole. SEAT BELT CONNECTOR LOWER HOOK Push. SEAT BELT 4 S LOWER HOOK UPPER TRIM 7. Remove the two seat foot covers (four retaining tabs). SEAT BELT COVER 700103CB 11. Remove the two seat belts from the left third row seat and remove the four bolts fastening the left third row seat to the floor. Remove the left third row seat. LEFT THIRD ROW SEAT FIX HOLE D2107AE 2 RETAINING S 2 RETAINING TABS LEFT THIRD ROW SEAT CUSHION SEAT FOOT COVER 2 RETAINING TABS 2 BOLTS 41-53 N m (4.2-5.4 kgf m, 30-39 lbf ft) 2 SEAT BELTS 4 BOLTS 41-53 N m (30-39 lbf ft) 8. Remove the two bolts that fasten the left third row seat to the floor. Raise the left third row seat cushion. 9. Remove the seat belt cover (two retaining clips). 4 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
12. Release the left rear side sill trim (four clips). LEFT SECOND ROW SEAT 14. Remove the weatherstrip in the area shown. Remove the left rear side lining (one hook, one bolt, one washer screw, one clip, six clips, and seven retaining tabs). 15. Using a plastic trim tool, open the lid on the left C-pillar trim (two retaining tabs). If equipped with speaker CONNECTOR If equipped. LEFT C-PILLAR TRIM 3 S LEFT SIDE STEP 7D1902AB 13. Open the two covers for the two tie-down hooks. Remove the two tie-down hooks from the left rear side liner (two screws). SEAT BELT BOLT COVER Open. 6 S WEATHERSTRIP BOLT WASHER SCREW HOOK Open. 7 RETAINING TABS 3 S LEFT C-PILLAR TRIM LID 2 RETAINING TABS 700104EB 2 SCREWS LEFT SIDE LINER WEATHERSTRIP 2 COVERS PLASTIC TRIM TOOL 2 TIE-DOWN HOOKS 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 5 of 16
16. Using a small rubber mallet and a shop towel, gently tap the left C-pillar trim at the area marked SIDE CURTAIN AIRBAG to release the clip. LEFT C-PILLAR TRIM PANEL 20. Remove the rear bumper (two clips, two bolts, two hex bolts and twelve self-tapping screws). Have an assistant help you when removing and installing the rear bumper. NOTE: Push down on the top of the rear bumper while pulling the bumper out. 6 SELF- TAPPING SCREWS Strike. PIN SHOP TOWEL LEFT C-PILLAR TRIM 2 HEX BOLTS 2 S 6 SELF- TAPPING SCREWS Installing the Control Unit 21. Install the control unit bracket on the control unit. RUBBER MALLET PART MARKED WITH SIDE CURTAIN AIRBAG 840210BB CONTROL UNIT 17. Remove the bolt from the left C-pillar trim. 18. Release the seat belt from the left C-pillar trim and remove the left C-pillar trim (three clips and unplug the vehicle connector if equipped). 19. Remove the clip from the left C-pillar trim, and install a new clip (supplied) to the left C-pillar trim. NEW LEFT C-PILLAR TRIM CONTROL UNIT 700202AB Discard. 6 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
22. Secure the control unit bracket to the vehicle panel with the 6 mm flange nut. 6 mm FLANGE NUT PANEL CONTROL UNIT 2 STOPS 24. Using isopropyl alcohol on a shop towel, clean the area where the buzzer will attach. Remove the adhesive backing from the buzzer, and attach the buzzer to the buzzer bracket as shown. ADHESIVE BACKING Align. Tightening point. CONTROL UNIT 700203CB Installing the Buzzer 23. Release the vehicle harness clip from the vehicle panel, and cut the clip to remove it from the vehicle harness. PANEL Cut off. 700205BB 25. Using one 6 mm flange nut, secure the buzzer bracket to the vehicle panel in the position where the vehicle harness clip was removed in step 23. Hold against the bracket. Clean with isopropyl alcohol. PANEL 6 mm FLANGE NUT 700206CB 700204AB 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 7 of 16
26. Secure the vehicle harness to the buzzer bracket with the offset wire tie as shown. 28. Secure the buzzer harness to the vehicle harness with three wire ties. OFFSET WIRE TIE 3 WIRE TIES 700207AB 27. Route the buzzer harness along the vehicle harness, and secure it to the vehicle harness with two wire ties. 700209AB 29. Plug the buzzer harness connector to the control unit. Bundle up the excess buzzer harness and loosely secure it to the vehicle harness with one wire tie. Bundle up the excess harness. CONTROL UNIT WIRE TIE CONNECTOR WIRE TIE Loosely secure. WIRE TIE Loosely secure. 8 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
30. Loosely secure the buzzer harness to the vehicle harness with one wire tie. Routing the Back-up Sensor Harness 31. Attach the 2A fuse label to the fuse case on the back-up sensor harness. 34. Unplug the vehicle 23-pin connector, and plug the back-up sensor harness 23-pin connector to the vehicle 23-pin connector as shown. 23-PIN CONNECTOR 23-PIN CONNECTOR 2A FUSE LABEL FUSE CASE 23-PIN CONNECTOR Lock. 6216030B 32. Plug the back-up sensor harness 12-pin connector to the control unit. 3-PIN CONNECTOR CONTROL UNIT 35. Lock the 23-pin connectors as shown. 36. Route the back-up sensor harness toward the underside of the vehicle, and secure it to the vehicle harness with three wire ties. 12-PIN CONNECTOR WIRE TIE WIRE TIE 33. Route the back-up sensor harness 3-pin connector as shown and secure it to the vehicle harness with two wire ties loosely secured in step 29 and 30. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 9 of 16
37. Remove the vehicle ground bolt from the vehicle ground terminal. Secure the back-up sensor harness ground terminal to the vehicle ground terminal with the vehicle ground bolt you just removed. 39. Remove the vehicle grommet from the vehicle panel. PANEL LIGHT GROUND BOLT Reuse. GROUND TERMINAL GROUND TERMINAL 700214BB GROMMET Discard. 700301BB 40. Route the back-up sensor harness through the vehicle grommet hole, and install the back-up sensor harness grommet into the vehicle panel. 38. Route the back-up sensor harness toward the rear of the vehicle, and secure it to the vehicle harness with three wire ties. GROMMET HOLE GROMMET Outside Cabin side WIRE TIE PANEL PANEL GROMMET 700302AB WIRE TIE 10 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
41. Slide the coupler clip onto the back-up sensor harness 6-pin connector, and secure it to the vehicle panel. Installing the Switch 43. On the back of the left rear side liner, cut the insulator to the measurement shown. 6-PIN CONNECTOR PANEL COUPLER LEFT SIDE LINING BACKSIDE 50 mm PUSHPIN RIB INSULATOR Cut. INSULATOR Peel. WIRE TIE 700303AB 42. Secure the back-up sensor harness to the vehicle harness with one wire tie. LEFT SIDE LINER (INSIDE) CENTER LEFT SIDE LINER 44. Using a pushpin, mark the left rear side liner in the center of the square as shown. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 11 of 16
45. While wearing eye protection, drill at the mark made in step 44 using a 26 mm hole saw. Remove any burrs. 26 mm HOLE SAW DRILL 46. Using a scissors, cut the cushion tape to the dimension shown. 10 mm UP CONNECTOR DOWN CUSHION TAPE CUSHION TAPE 26 mm HOLE MARK LEFT SIDE LINING LEFT SIDE LINER SIDE VIEW Hole in the switch. SMALL WIRE TIE Hole on the switch. SMALL WIRE TIE LEFT SIDE LINER 47. Using isopropyl alcohol on a shop towel, clean the area where the cushion tape will attach. Attach the cushion tape you cut in step 46 to the switch bracket as shown. 48. Insert the switch into the 26 mm hole, and install the switch bracket onto the switch as shown. 49. Secure the switch bracket to the switch with one small wire tie. 12 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
50. Plug the back-up sensor harness 3-pin connector to the switch. Reinstall the left rear side lining and C-pillar trim. 3-PIN CONNECTOR 52. While wearing eye protection, drill the outer pierced marks with a 3 mm bit. Then drill the two outboard center marks using a 24 mm hole saw. Remove all burrs. 3 mm DRILL BIT DRILL BURRS Remove. 24 mm HOLE SAW LEFT SIDE LINING Installing the Back-up Sensor 51. Locate the four preset marks on the inside of the bumper. Using a pushpin, pierce each of the four preset marks in two places. Make sure you pierce the right center mark in the center and the bottom. PUSHPIN SCRIBE MARK 53. While wearing eye protection drill the right inner mark at the upper pierced mark with a 3 mm drill bit. On the left inner mark, drill the lower pierced mark with a 3 mm drill bit. Then drill the two center marks using a 26 mm hole saw. Remove all burrs. 3 mm DRILL BIT DRILL BURRS Remove. 26 mm HOLE SAW 3 mm DRILL BIT DRILL 26 mm HOLE SAW PUSHPIN SCRIBE MARK BURRS Remove. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 13 of 16
54. Install the two corner sensors in the rear bumper, using one sensor clip for each sensor. 56. Plug the four back-up sensor subharness 2-pin connectors to the two corner sensors and two center sensors. CORNER 2 CENTER S (LARGER) 24 mm 2 HOLES CORNER DETENT Outside view CORNER CORNER Inside view 2 S 4 SUB 2-PIN CONNECTORS SUB 55. Install the two center sensors in the rear bumper using one sensor clip for each sensor. Outside view Inside view 700315AB 57. Attach three back-up sensor subharness clips (A) into three sensor clips. 26 mm HOLE DETENT SUB CENTER (LARGER) CENTER (LARGER) DETENT CENTER (LARGER) CENTER (LARGER) Outside view 26 mm HOLE Inside view 3 S 3 SUB S (A) 700316AB 14 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
58. Attach the four back-up sensor subharness clips (B) to the rear bumper as shown. SUB (B) Secure point. Secure point. SUB (B) 59. Using isopropyl alcohol on a shop towel, clean the area where the harness tape will attach. Secure the back-up sensor subharness to the rear bumper with one harness tape. SUB SUB Secure point. TAPE Secure point. SUB (C) 700318AB SUB (B) Secure point. SUB (B) 700317AB 60. Secure the back-up sensor subharness to the rear bumper with one back-up sensor subharness clip (C). 61. Bring the rear bumper to the vehicle, and plug the back-up sensor subharness 6-pin connector into the back-up sensor harness 6-pin connector. Reinstall the rear bumper. 6-PIN CONNECTOR SUB 6-PIN CONNECTOR 700319AB 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43298 (1003) 15 of 16
62. Check that all wire harnesses are routed properly and all connectors are plugged in. 63. Reinstall all removed parts. 64. Reconnect the negative cable to the battery. 65. Enter the customer s audio system or navigation system anti-theft code. 66. Reset the clock. 67. Check the back-up sensors function as described in the Accessory User s Information Manual. 68. Put the Accessory User s Information Manual in the glove box. 16 of 16 AII 43298 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.