WWMF1 Solenoid operted spool vlve with soft switching Flnge construction 4/3-wy with spring centred mid position 4/2-wy with spring reset Q mx = 12 l/min p mx = 35 r DESCRIION Direct operted solenoid spool vlve with 4 connections in 5 chmer design. With the solenoids deenergised, the spool is held in the center position y the spring (4/3), or switched ck to the offset position (4/2). he soft switching of the vlve is chieved y mens of n optimum comintion of the orifice nd spool design. recise spool fit, low lekge, long service life time. Spool mde from hrdened steel, ody from high qulity hydrulic cst steel. Wide rnge of stndrd nd specil voltges. NG1 ISO 441-5 LICION Norml solenoid spool vlves switch very quickly. his cn led to shocks in the hydrulic system which cn cuse mechnicl wer nd hve negtive effect on opertion. he soft switching vlves slow down nd dmpen the switching movements which enefits the system. Optimum results cn e chieved if ll 4 connections re connected nd the vlve is properly vented. SYMOL 1 2 C C1 C2 o D D1 D2 o EE1 E2 o GENERL SECIFICIONS Designtion Construction Mounting 4/2-, 4/3-spool vlve Direct operted Flnge construction Nominl size NG1 ccording to ISO 441-5 ctution mient temperture Weight MFd Switching solenoid -25 +7 C (NR) -2 +7 C (FKM) if > +5 C, then no undervoltge is dmissile 3,9 kg (1 solenoid) 5,4 kg (2 solenoids) 15 yers HYDRULIC SECIFICIONS Working pressure nk pressure Mximum volume flow Lekge volume flow Fluid p mx = 35 r p mx = 16 r Q mx = 12 l/min, see chrcteristics see chrcteristics Minerl oil, other fluid on request Viscosity rnge 12 mm 2 /s 32 mm 2 /s emperture rnge fluid Contmintion efficiency -2 +7 C Clss 2 / 18 / 14 Filtrtion Required filtrtion grde ß 1 16 75, see dt sheet 1.-5 www.wndfluh.com Illustrtions re not inding Dt suject to chnge 1/5 Edition: 16 22 1.4-42 E
WWMF1 YE CODE Spool vlve, soft switching W W M F 1 - - / - # Slip-on coil Medium Flnge construction Interntionl stndrd interfce ISO, NG1 Designtion of symols cc. to tle Nominl voltge U N 12 VDC G12 VDC G 115 VC R115 23 VC R23 without coil X5 Slip-on coil Metl housing round W (only G12 nd G) Metl housing squre M Connection execution Connector socket EN 17531-83 / ISO 44 D Connector socket M Junior-imer J (only for U N 75 VDC) Connector Deutsch D4-2 G (only for U N 75 VDC) Seling mteril Mnul override NR FKM (Viton) Integrted ush-utton Spindle D1 HF1 HS1 Orifice dimeter Ø,3 mm Q,3 Ø,5 mm (Stndrd) Ø,8 mm Q,8 Spindle (djustle soft switching) S Design index (suject to chnge) 1.4-42 ELECRICL SECIFICIONS rotection clss Reltive duty fctor Switching frequency Service life time Voltge tolernce Stndrd nominl power Connection execution D: I65 Connection execution J: I66 Connection execution G: I67 nd I69K 1 % DF Since switching is dmped nd slow, switching frequency is of secondry importnce. 1 7 (numer of switching cycles, theoreticlly) ± 1 % with regrd to nominl voltge 12 VDC, VDC, 115 VC, 23 VC C = 5 to 6 Hz, rectifier integrted in the connector socket Note! Other electricl specifictions see dt sheet 1.1-19 (slip-on coil W) nd 1.1-193 (slip-on coil M) CUION ctution Switching solenoid, wet pin push type, pressure tight Execution W.E64/31x72 (Dt sheet 1.1-19) W.S6/31x72 (Dt sheet 1.1-193) Connection Connector socket EN 17531 83 Connector socket M Junior-imer Connector Deutsch D4-2 MNUL OVERRIDE Integrted ( ) ctution pin integrted in the rmture tue. ctution y pressing the pin ush-utton (HF1) Integrted in the knurled nut. ctution y pressing the push-utton Spindle (HS1) Integrted in the knurled nut. ctution y turning the spindle (continuously vrile vlve ctution) ttention! he ctution of the mnul override is possile up to tnk pressure of: 2 r Integrted ( ) 2 r ush-utton (HF1) 8 r Spindle (HS1) www.wndfluh.com Illustrtions re not inding Dt suject to chnge 2/5 Edition: 16 22 1.4-42 E
WWMF1 ERFORMNCE SECIFICIONS Oil viscosity υ = 3 mm 2 /s p = f (Q) p [r] K419 35 3 25 2 15 1 5 erformnce limits Mesured with nominl voltge -1 % 1 / 2 E D, C 2 4 6 8 1 12 Q [l/min] Δp = f (Q) p [r] K411 2 15 1 5 ressure drop volume flow chrcteristics 1 2 3 4 5 Volume flow direction Symol - - - - - 1 / 2 4 4-2 1 C 5 5-4 3 D 5 5-4 3 E 5 5 3 5 4 2 4 6 8 1 12 Q [l/min] Q L = f (Q) Lekge volume flow chrcteristics per control edge Q [cm 3 /min] K4111 25 2 15 1 5 5 1 15 2 25 3 35 p [r] Switching times, influence of the soft switching Switching off the solenoid Mesured with WWMF1-C-G compred with WDMF1-C-G t Q = 9 l/min Switching times, influence of the soft switching Switching on the solenoid Mesured with WWMF1-C-G in comprison with WDMF1-C-G t Q = 9 l/min 3 25 2 15 1 5 Note! U [V] p E [r] K4113 WDMF1-C (strk systemhängig) Düse,8 Düse,3 Düse,5.1.2.3.4.5.6.7.8.9 1 t [s] With the option spindle S, the switching time cn e djusted individully. U [V] 3 25 2 15 1 5 p E [r] K4112 WDMF1-C (strk systemhängig) Düse,8 Düse,5 Düse,3.1.2.3.4.5.6.7.8.9 1 t [s] www.wndfluh.com Illustrtions re not inding Dt suject to chnge 3/5 Edition: 16 22 1.4-42 E
WWMF1 DIMENSIONS 4/3-wy vlve (spring centred) 4/2-wy vlve (spring reset) X 13 14 E 29 14 W = 64 69.5 HF1 65 51 37 HS1 71 51 7 6 1 5 MD= 5Nm 214 6.5 1.5 35 72 93 14 8 9 * X 15 M = 6 1 *optionlly spindle 35 72 E = ir leed screw Orifices in vlve ody influence the switching times 214 HYDRULIC CONNECION 46 54 2.8 o 1.5 16.8 9.7 RS LIS osition rticle Description 1 26.3... 26.9... 5 16.212 16.81 W.E64 / 31 x 72 M.S6 / 31 x 72 O-ring ID 12,42 x 1,78 (NR) O-ring ID 12,42 x 1,78 (FKM) 6 16.2282 O-ring ID 28. x 2.62 (NR) 7 154.276 Knurled nut 8 253.76 ush-utton 9 253.75 Spindle 13 6.36 Socket hed screw M6 x 2 DIN 912 14 49.262 onded sel ID 4,1 x 7,2 x 1 SURFCE REMEN he vlve ody is pinted with two component pint he screw plug is zinc coted he slip-on coil nd the rmture tue re zinc-nickel coted COMMISSIONING ttention! When commissioning, the vlve must e vented under pressure (mx. 2 revolutions of screw E). www.wndfluh.com Illustrtions re not inding Dt suject to chnge 4/5 Edition: 16 22 1.4-42 E
WWMF1 CCESSORIES Mting connector grey () rticle no. 219.21 Mting connector lck () rticle no. 219.22 Fixing screws Dt sheet 1.-6 hreded supltes Dt sheet 2.9-3 Multi-sttion supltes Dt sheet 2.9-6 Horizontl mounting locks Dt sheet 2.9-1 echnicl explntions Dt sheet 1.-1 Hydrulic fluids Dt sheet 1.-5 Filtrtion Dt sheet 1.-5 Reltive duty fctor Dt sheet 1.1-43 INSLLION NOES Mounting type Mounting position ightening torque ttention! Flnge mounting 4 fixing holes for socket hed screws M6 x 4 ny, preferly horizontl Fixing screw M D = 1,5 Nm ± 1 % (screw qulity 8.8, zinc coted) mx. tnk pressure 8 r M D = 13,5 Nm ± 1 % (screw qulity 1.9, zinc coted) Knurled nut M D = 5 Nm he length of the fixing screw depends on the se mteril of the connection element. SNDRDS Mounting interfce ISO 441-5 Solenoids DIN VDE 58 Connection execution D EN 17531 83 rotection clss EN 6 529 Contmintion efficiency ISO 446 SELING MERIL NR or FKM (Viton) s stndrd, choice in the type code Wndfluh G ostfch CH-3714 Frutigen el. +41 33 672 72 72 Fx +41 33 672 72 12 sles@wndfluh.com www.wndfluh.com Illustrtions re not inding Dt suject to chnge 5/5 Edition: 16 22 1.4-42 E