MADE IN SWEDEN Friction Transporter Installation & Service Manual 203-04-2
TPE 00 Installation TPE 00 Manual Installation. TPE 00 should be mounted so the tray can move without obstruction in both directions. Mount the Transporter so no risk of crushing hazard might occur to personnel. TPE 00 should be connected to 380 V 3 phase 6 A and via a motor protection circuit breaker. Direction of rotation. The motor rotates clockwise, see arrow on motor. Note. TPE 00 does NOT feed in the other direction if you switch the rotation direction. You will then only get a lesser efficiency level. If the worm gear unit is turned upside down, you will need to change the rotation direction. Change of motor position. Pos. 02: by removing these three (3) screws the motor can be positioned in 90 degrees intervals. WARNING, this requires two (2) persons as the motor is spring loaded. Operation switch. Pos. 03: Connector to speed monitor. A speed monitor is mounted on the Transporter, this can be used to indicate a disruption warning in the case that the Transporter stops. Maintenance. Pos. 0: Grease nipples 4 pcs. Lubricate with a few pulls of a grease gun once a month. 03 02 Matningsriktning Feed direction 0
TPE 00 Service Please note that some parts may not be available because they are not field replaceable. If this is the case, a subassembly must be used. Some parts are only available as a subassembly and cannot be purchased individually. Check the spare parts reference lists for details. Disassembly.. Apply a vise to the TPE 00 according to the schematic below 40-50 mm 2. Remove screws 00-204 (3 pcs). 3. Carefully loosen the vise 40-50 mm, the tension is ca 00 kg. 4. Remove the yoke with springs and spring guides. 5. Loosen the set screws 00-230 (4 pcs) 6. Remove the screws 00-203 (8pcs) and remove the slide frame. 7. Disassemble the bearing support by removing the screws 40-054. 8. Remove the locking nut 00-244 and remove the curve with the axle. Reassembly.. Reassemble in reverse order. 2. Adjust the set screws 00-230 so that the slide frame slides effortlessly without play.
TPE 00 Dimensional drawing
TPE 00 Spare parts Part No. Description Qty Part No. Description Qty 0-20 Screw 3 00-256 Magnet 5-206 Screw 3 00-260 Wedge 30-202 Screw 6 00-265 Grease nipple 4 40-027 Washer 3 00-280 Support ring 40-054 Screw 4 00-285 Snap ring 40-055 Screw 2 00-295 Snap ring 00- Bearing support 00-30 Track runner bearing 00-3 Guide plate 00-302 Ball bearing 00-5 Attachment plate 00-40 Electric motor 00-20 Slide frame 00-403 Worm gear 00-2 Rear holder 00-404 Motor coupling 00-23 Spring sleeve 3 00-40 Speed monitor 00-24 Bearing shaft 00-4 Socket 00-28 Curve 00-43 Plug in 00-29 Axle 00-440 Plint 00-30 Adapter attachement 40-05 Mounting insert 8 00-3 Sensor attachement 00-32 Plate Subassemblies 00-34 Tube 00-40 Attachment 00-60 Linear guide Qty 00-4 Guard 00-3 Prism * 2 00-202 Screw 0 00-32 Stop 2 00-203 Screw 9 00-33 Roller guide * 00-204 Screw 7 00-205 Screw 4 00-602 Spring guide Qty 00-207 Screw 4 00-22 Spring guide * 00-230 Screw 4 00-245 Insert * 00-235 Screw 2 00-236 Screw 2 00-605 Worm gear Qty 00-240 Nut 4 00-402 Motor attachment * 00-24 Washer 00-403 Worm gear * 00-243 Nut 00-405 Screw * 4 00-244 Locking nut 4 00-250 Spring 6 * Not sold separately
TPE 00 Spare parts
TPE 00 Spare parts
TPE 00 Spare parts
TPE 00 Spare parts
Technical data TPE 5/9 Max load capacity Max tray weight Stroke length Feed rate Sound level Motor effect Electrical connection 5 kg 3 kg 9 mm 4-8 m/min 55 db (A) 0, kw 0-240 V TPE 30/9 Max load capacity Max tray weight Stroke length Feed rate Sound level Motor effect Electrical connection 30 kg 5 kg 9 mm 4-8 m/min 60 db (A) 0, kw 0-240 V TPE 00 Max load capacity Max tray weight Stroke length Feed rate Sound level Motor effect Electrical connection 00 kg 35 kg 6 mm 8-0 m/min 62 db (A) 0,5 kw 380-45 V 50-60 Hz. alternatively 0-20 V
Contact information Factory repair service. If your Transporter requires repair, return it prepaid to our Service Center. Repairs include fault tracing and repair or replacement of failed components, as well as final testing to ensure your Transporter is functioning according to specifications. All items within the warranty period are evaluated by technicians to verify warranty eligibility. All Transporters repaired through Mectool receive a new three month manufacturer's warranty (wear parts excluded). Mectool Sweden AB PJ Rösiös Väg 2-3 293 40 Olofström Sweden Phone: Fax: Email: Web: +46 454 30 90 40 +46 454 46 56 info@mectool.se www.mectool.se