INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SHJ-100A 2010 ODYSSEY AII 41829 Issue Date JUNE 2009 PARTS LIST Relay Left fog light 22 Wire ties Right fog light Wire tie with holder Fog light harness Short subharness (With LX model) 5 Wire ties with clip Long subharness (With EX model and Touring) 2 Small wire ties Relay bracket 2 Tapes 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 08V31-SHJ-1A00-91 1 of 18
Washer-bolt, 6 x 16 mm 2 Self-tapping screws Ground bolt TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Stubby #2 Phillips screwdriver 10 mm Socket Ratchet Diagonal cutters 10 mm Combination wrench Flat-tip screwdriver Blanket Isopropyl alcohol Shop towel Scissors INSTALLATION Grommet EPT sealer Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be careful not to damage the body finish. Take care not to damage the clips and tabs. 2 Spring nuts 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Remove the radiator cover (eight clips). 8 CLIPS Fuse label (LX model only) 20 A Fuse (LX model only) Lighting switch RADIATOR 7424030Y 2 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
4. Remove the front bumper. On each side, pull down the inner fender cover and remove the four self-tapping screws. Remove the eight clips. Remove the two clips, and have an assistant help you remove the front bumper. Place the front bumper on a blanket. 6. Remove the under-hood fuse relay box cover, two bolts, and one retaining tab, and move the underhood fuse relay box to the side. 4 RETAINING TABS UNDER-HOOD FUSE RELAY BOX RETAINING TAB BOLT 2 SELF- TAPPING SCREWS INNER FENDER (Pull down.) CLIPS INNER FENDER (Pull down.) BOLT UNDER- HOOD FUSE RELAY BOX 2 SELF- TAPPING SCREWS 7424080Y 8 CLIPS Routing the Fog Light Harness FRONT BUMPER 5. Open the hood. Remove the FI-ECU cover (two clips and one tab). 7424041Y FI-ECU TAB 2 CLIPS FI-ECU 4306080Y 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 3 of 18
7. Remove the under-hood fuse/relay box lower cover from the under-hood fuse/relay box (six retaining tabs). UNDER-HOOD FUSE/RELAY BOX 10. Remove the sub fuse box from the vehicle SUB FUSE BOX CASE UNDER-HOOD FUSE/RELAY BOX LOWER 6 RETAINING TABS TAB SUB FUSE BOX 4519050Y If the vehicle you are working on is an LX model, go to step 19; otherwise, continue with step 8. 8. Near the under-hood fuse/relay box, locate the sub fuse box. Remove the sub fuse box cover (two tabs). SUB FUSE BOX 2 TABS SCREW UNDER-HOOD FUSE RELAY BOX BRACKET 4308020Y bracket. 11. Remove the sub fuse box from the case (one tab). 12. Get the long subharness. Plug the 1-pin terminal from the long subharness into the rear of the sub (Rear view) SUB FUSE BOX SUB FUSE BOX UNDER-HOOD FUSE/RELAY BOX 4308010Y 9. Remove the screw and disconnect the vehicle harness. SUB FUSE BOX LONG SUB 4308032Y 4 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
fuse box at the location shown. 13. Secure the long subharness to the sub fuse box under-hood fuse/relay box. 16. Disconnect the vehicle 18-pin connector from the SMALL WIRE TIE SUB FUSE BOX BACK OF THE UNDER-HOOD FUSE/RELAY BOX 18-PIN LONG SUB harness with one small wire tie. 14. Reinstall the sub fuse box. UNDER-HOOD FUSE RELAY BOX 7424090Y 15. Secure the long subharness to the vehicle harness Lock TERMINAL OF FOG LIGHT Blue/Black 4308050Y back of the under-hood fuse/relay box. 17. Get the fog light harness. Release the lock on the vehicle 18-pin connector as shown, and plug the terminal of the fog light harness into the back of SUB FUSE BOX 18-PIN (Harness side view) UNDER- HOOD FUSE/ RELAY BOX LONG SUB WIRE TIE 7424100Y 18-PIN 7424110Y the 18-pin connector in the location shown. 18. Reconnect the vehicle 18-pin connector into the 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 5 of 18
with one wire tie. 19. Disconnect the vehicle 20-pin connector from the BOTTOM OF THE UNDER- HOOD FUSE/ RELAY BOX under-hood fuse/relay box.then, go to step 22. 22. Plug the connector from the long/short subharness into the fog light harness connector. Secure the fog light harness and the subharness to the vehicle SHORT SUB (LX model) 20-PIN SMALL WIRE TIE LONG SUB (EX/Touring model) 4308070Y bottom of the under-hood fuse/relay box. 20. Get the short subharness, and plug the 1-pin terminal from the short subharness into the back SHORT SUB 1-PIN LOCATION 20-PIN Lock harness with one small wire tie. 23. Reinstall the under-hood fuse/relay box lower cover in the original position. WIRE TIE WITH HOLDER 4308091Y 24. Below the under-hood fuse relay box, secure the fog light harness connector to the vehicle (Harness side view) SHORT SUB 1-PIN TERMINAL 20-PIN UNDER- HOOD FUSE/ RELAY BOX SUB 4308062Y of the vehicle 20-pin connector. 21. Reconnect the vehicle 20-pin connector into the UNDER- HOOD FUSE RELAY BOX 7627020B 6 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
harness using the wire tie with holder. 25. Route the fog light harness 2-pin connector (short side) forward along the vehicle harness, and loosely secure it to the vehicle harness with two the vehicle harness and into the bumper area. 27. Attach the two wire ties with clip from the fog light TAPE 2 WIRE TIES WITH CLIP GREEN TAPE OF RIGHT HEADLIGHT 2 WIRE TIES (Loosely secure.) WASHER TANK FRAME 7424131Y 7627030B harness into the holes in the vehicle body. 28. Using isopropyl alcohol, throughly clean the areas where the tape will attach. Secure the fog light wire ties. 26. Route the fog light harness 2-pin connector along harness to the vehicle s frame with the tape. 29. Secure the fog light harness to the vehicle 2 WIRE TIES WIRE TIE HORN 2-PIN MAIN 4309040Y WIRE TIE WITH CLIP 7627040B 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 7 of 18
harness with two wire ties. RIGHT HEADLIGHT vehicle bracket. 33. Route the fog light harness along the vehicle harness. Attach the fog light harness to the vehicle FRONT 3 WIRE TIES 2 WIRE TIES (Tighten.) WASHER TANK 7627051B 30. Tighten the two wire ties from step 25. 31. Reinstall the under-hood fuse relay box. 32. Remove the power steering reservoir from the BRACKET 7627030B POWER STEERING RESERVOIR harness with three wire ties. 34. Route the fog light harness along the vehicle harness of the bulkhead, and loosely secure the fog light harness to the vehicle harness with five BULKHEAD FRONT 5 WIRE TIES (Loosely secure.) 4309070Y 7627060B 8 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
wire ties. 35. Route the fog light harness past the battery, and loosely secure it to the vehicle harness with three harness into the hole in the body panel. 3 WIRE TIES (Loosely secure.) FRONT BOLT Reuse. RESONATOR CHAMBER 7424150Y BATTERY 38. Remove the vehicle bolt. 7627070B wire ties. 36. Locate the wire tie with clip near the end of the fog light harness. Wrap an EPT sealer around the fog WIRE TIE WITH CLIP EPT SEALER 120 mm 4707010Y BODY PANEL 39. Route the fog light harness as shown. WIRE TIE WITH CLIP light harness at the measurement shown. 37. Attach the wire tie with clip from the fog light 4310010Y 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 9 of 18
40. Reinstall the vehicle bolt removed in step 38. If equipped with AUTO air conditioner: 41. Remove the vehicle bolt from the vehicle bracket. Secure the ground terminal from the fog light harness to the vehicle bracket using the ground SENSOR it with three wire ties with clip to the vehicle frame. 45. Using isopropyl alcohol, thoroughly clean the area where the tape will attach. Secure the fog light TAPE FRAME BRACKET BOLT (Discard.) GROUND TERMINAL GROUND BOLT 3 WIRE TIES 4310031Y bolt supplied. 42. Secure the fog light harness to the sensor harness using three wire ties. Go to step 45. If equipped with MANUAL air conditioner: 43. Use the ground bolt and tighten the ground terminal of the fog light harness to the vehicle 7702010B harness to the vehicle frame with one cushion tape. 46. Tighten the eight wire ties you loosely secured to the vehicle harness. 47. Get the relay bracket and the relay. Attach the RELAY BRACKET FRAME 3 WIRE TIES WITH CLIPS 6 x 16 mm WASHER- BOLT RELAY 7424170Y GROUND BOLT GROUND TERMINAL 7627080B frame. 44. Route the fog light harness as shown, and secure 10 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
relay to the relay bracket using 6 x 16 mm washerbolt. RELAY and slide the tab from the fog light relay bracket under the bolt. Retighten the relay bracket bolt. FRONT 4-PIN 7424180Y 48. Plug the fog light harness 4-pin connector into the relay. 49. Loosen the bolt securing the existing relay box, RELAY 3 WIRE TIES 7424200Y 50. Secure the fog light harness from the relay box to the vehicle harness with three wire ties. FRONT BUMPER FRONT BOLT EXISTING RELAY BOX FRAME 4 RETAINING TABS 7424190Y 7424051Y 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 11 of 18
51. Remove the cover from the front bumper (four retaining tabs). SPRING NUT OPENING NOTE: Have an assistant help you when removing and installing the front bumper. 2-PIN 2 GROMMETS FRONT BUMPER 7424061Y 52. Slide the spring nut onto the cover opening as shown. 53. Install the nut to the front bumper. 54. Repeat steps 51 thru 53 on the right side. 55. Reinstall the front bumper in its original position, and route the fog light harness 2-pin connectors through each cover opening. Make sure that the fog light harness does not get caught. RIGHT LEFT 2-PIN 7919010X 56. Plug the fog light harness 2-pin connectors into the fog lights. 57. Insert the hook into the cover opening and insert the pivot to the nut installed in step 53. FRONT BUMPER OPENING 2-PIN HOOK OPENING 2-PIN 5 x 16 mm SELF-TAPPING SCREW PIVOT LEFT 7424073Y FRONT BUMPER OPENING 7424211Y 58. Install the left fog light on the front bumper using 12 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
the 5 x 16 mm self-tapping screw. 59. Repeat steps 57 thru 58 on the right side. Installing the Fog Light Switch STEERING COLUMN UPPER 61. Remove the steering column lower cover (one screw and two self-tapping screws). 62. Unlock the steering column tilt lever. Pull the steering wheel out towards you and down. Drop STEERING COLUMN Push. 2 RETAINING TABS Push. WHITE 2 BLACK S 4 RETAINING TABS STEERING COLUMN LOWER SCREW 2 SELF-TAPPING SCREWS 60. Remove the steering column upper cover (six retaining tabs). 782103AY STEERING COLUMN 7425010Y the steering column lower cover down to access the lighting switch. 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 13 of 18
63. Disconnect the three vehicle connectors from the steering column. 64. Turn the steering wheel counterclockwise as shown. Remove the two self-tapping screws from the lighting switch. While pushing the retaining tab, slide the lighting switch and remove it from the steering column. Do not pull out the lever when lever when installing the case. Push the case and set the retaining tab to the tab hole securely. 66. Install the 20 A fog light fuse. <TOP VIEW> TAB HOLE STEERING COLUMN 20 A FUSE CASE FUSE LOCATION LIGHTING SWITCH LEVER RETAINING TAB 2 SELF-TAPPING SCREWS STEERING WHEEL (Turn counterclockwise.) 7425020Y SUB FUSE BOX FUSE LOCATION 4520020Y EX/EX-L: Install the 20 A fuse into the sub fuse box in the location shown. removing the case. Do not damage the tab hole of the steering column. 65. Install the new lighting switch on the steering column using the two self-tapping screws. Hold the case by hand, then install the new lighting switch to the steering column. Do not push the TOP VIEW 20 A FUSE TAB HOLE STEERING COLUMN CASE NEW LIGHTING SWITCH UNDER-HOOD FUSE RELAY BOX 4520010Y LEVER RETAINING TAB 2 SELF-TAPPING SCREWS 7425030Y 14 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
LX model: Install the 20 A fuse into the underhood fuse relay box in the location shown. FUSE LABEL 73. Initialize and test the front window auto up/down function. Fog Light Aiming Adjustment 74. Adjust the fog lights. Adjust the aiming according to local laws and regulations. ADJUSTING SCREW TO LOWER TO RAISE UNDER-HOOD FUSE RELAY BOX 7702020B 67. LX model only: Attach the 20 A fuse label to the inside of the under-hood fuse relay box. 68. Check that all wire harnesses are routed properly and all connectors are plugged in. 69. Reinstall all removed parts. 7425051Y 70. Reconnect the negative cable to the battery. 71. Enter the customer s audio unit anti-theft code, and reset the station presets. 72. Reset the clock. 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 15 of 18
To adjust, turn the adjustment screw in or out until the correct aiming is obtained. USE AND CARE How to Operate Fog Lights Turn the lights switch to the position (headlights on low beam). Turn the fog light switch on (indicator is on). NOTE: The fog light lenses may cloud when the outside temperature is cold; this is normal and should go away in warm weather. If the fog light does not come on, check the fuse and all the connectors, including the ground cable. Replacing the Bulb NOTE: Use only a Honda Genuine halogen light bulb of specified wattage. BULB, (H11) P/N 33165-S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a clean, soft cloth that has been dampened with denatured alcohol or a mild detergent solution. 1. Remove the fog light (5 x 16 mm self-tapping screw, pivot, hook, and disconnect the fog light harness 2-pin connector). NOTE: Make sure that the nut is still installed to the cover opening. If the nut is removed with the FRONT BUMPER 5 x 16 mm SELF-TAPPING SCREW PIVOT 2-PIN HOOK 7919020Y left fog light, reinstall the nut onto the cover opening. BULB 7425062Y 16 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.
2. Disconnect the connector from the bulb and remove the bulb from the fog light. 3. Install the new bulb into the fog light. NOTE: When installing the new bulb, align the cutout on the fog light with the tab on the new bulb Turn. NEW BULB NEW BULB 7425072Y and turn the new bulb in completely. If not properly aligned, the fog light may blind oncoming drivers. 4. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw and bolts securely. 5. Check the operation of the fog light; adjust the aiming if necessary. 2009 American Honda Motor Co., Inc. - All Rights Reserved. AII 41829 (0906) 17 of 18
CIRCUIT DIAGRAM SUB FUSE BOX No.7 (20A) No.10 (20A) LX MODEL UNDER-HOOD FUSE/RELAY BOX L/R UNDER-DASH FUSE/RELAY BOX MICU FRONT FOG LIGHT RELAY L L/G COMBINATION LIGHT SWITCH COMBINATION SWITCH CONTROL UNIT W L/B RIGHT FOG LIGHT B LEFT FOG LIGHT RELAY CONTROL MODULE B OFF FOG LIGHT B FR FOG SWITCH BLK BLACK BRN BROWN LIGHT SWITCH YEL BLU YELLOW BLUE ORN PUR ORANGE PURPLE OFF Low Hi GRN GREEN NAT NATURAL SWITCH OFF ON - - - - - - ON - RED WHT LT BLU RED WHITE LIGHT BLUE PNK GRY LT GRN PINK GRAY LIGHT GREEN 7919030X 18 of 18 AII 41829 (0906) 2009 American Honda Motor Co., Inc. - All Rights Reserved.