IRCTIONAL CONTROLS The Yuken Multi-Purpose Valves Comply with The Needs of Reducing Cost and Size of Your Machine YUKN's Multi Purpose Valve s are compound valves composed of the main valve having four poppets, / Solenoid Operated irectional Valves for pilot and Pilot Selector Valves. This valve is multifunctionalized by having individual poppet had functions such as directional control, flow control or pressure control according to the combination of the main valve and pilot selector valve. Features Multi-purpose control valves The valves combine three functions of directional control, flow control and of pilot operated check valve (or counterbalance valve). The valves contribute for reducing a number of valves in applications and space for installation and then eventually leads to reduction in size and cost of your machines. Quick response, High reliability Changeover response time is very quick as the valves are poppet type, there is no over-lap. No hydraulic lock occurs as there is no leakage of pressurised oil from the seat parts. asy to reduce shock in your hydraulic system By selecting proper diameter of orifice for pilot, the open/close timing of the flow passage can be set freely. Therefore, smooth starting and stopping of actuator can be done combined with using shockless type poppet. Noise of ON/OFF and vibration of piping in hydraulic system can be also reduced. For regenerative circuit position- way type, which is to compose regenerative circuit, is available. By adopting regenerative circuit, gaining fast feed speed by using smaller volume pump is possible. Therefore saving electric power of system is possible. The mounting dimensions are conformed with ISO standard The valves are interchangeable with our conventional valves in mounting. Solenoid Operated irectional Valve for Pilot Orifice By selecting proper diameter of orifice for pilot, the open/close timing of the flow passage can be set freely. Pilot Selector Valve X Y Section X-X X T T Y Section Y-Y A B Flow Adjustment Screw P Main Valve Seat Spring Shockless Type Poppet 9
Specifications SLHG--- - SLHG--- - SLHG--- - SLHG-- - - - SLHG-- - - - SLHG-6-- - SLHG-6-- - SLHG-6-- - SLHG-6- - - SLHG-6- - - SLHG--- - SLHG--- - SLHG--- - SLHG-- - - SLHG-- - - Max. Flow L/min (U.S.GPM) (9.6) {} (9.6 {6.}) (79.) {} (79. {.}) () {} ( {79.}) Max. Operating Pressure MPa (PSI) Max. Pilot Pressure MPa (PSI) Max. T-Line Back Pres. MPa (PSI) (6) (6) 6 () (6) (6) 6 () (6) (6) 6 () In case of counterbalance function line, maximum flow is limited to the values in brackets. Pressure Adj. Range of Counterbalance MPa (PSI) Refer to Model No. esignation Refer to Model No. esignation Refer to Model No. esignation Ratio of Poppet Area (Seat Area: Annular Area) irection & Flow : Pressure : : : : : : : : Approx. Mass kg (lbs.) () () 9 () (). () 6. (9) 6. (9) (6) (6). (76) 9 () 9 () 6 (7) 6. () 67 () Solenoid Ratings Refer to Pilot Valve (SG- Series Solenoid Operated irectional Valve) Solenoid Ratings on page. Model Number esignation F- Special Seals SLH Series Number F: SLH: For phosphate Multi-Purpose ester type fluids Valve (Omit if not required). See "Min. Adjustment Pressure", page 6, for information on minimum adjustment pressure. G Type of Mounting G: Sub-plate Mounting - Valve Size 6 - Type of Pilot A Counterbalance Function A : AT Line W: AT & BT Lines A : AT Line W: AT & BT Lines A : AT Line W: AT & BT Lines See page 6 for functions and purpose of use. -B Pressure Adj. Range of Counterbalance MPa (PSI) B : - 7 ( - ) H : 6 - (7-6) None: None: - ( - 6) - ( - 6) 6
IRCTIONAL CONTROLS Sub-plate Valve Model Numbers SLHG- SLHG-6 SLHG- Japanese Standard "JIS" uropean esign Standard N. American esign Standard Sub-plate Model Numbers HGM-- HGM-X- HGM-6- HGM-6X- HGM-- HGM-X- Thread Size Rc / Rc / Rc / Rc Rc -/ Rc -/ Approx. Mass kg (lbs.).. 7. 7. (9.7) (9.) (6.) (6.). (7.). (7.) Sub-plate Model Numbers HGM-- HGM-X- HGM-6- HGM-6X- HGM-- HGM-X- Thread Size / BSP.F / BSP.F / BSP.F BSP.F -/ BSP.F -/ BSP.F Approx. Mass kg (lbs.).... (9.7) (9.) (.7) (.7). (7.). (7.) Sub-plate Model Numbers HGM--9 HGM-X-9 HGM-6-9 HGM-6X-9 HGM--9 HGM-X-9 Thread Size / NPT / NPT / NPT NPT -/ NPT -/ NPT Sub-plates are available. Specify the sub-plate model number from the table above. When sub-plates are not used, the mounting surface should have a good machined finish. These sub-plates are sharable with those for SHG Series Solenoid led Pilot Operated irectional Valve. For dimensions, see pages to. Approx. Mass kg (lbs.).. 7. 7. (9.7) (9.) (6.) (6.). (7.). (7.) Mounting Bolts Socket head cap screws in the table below are included. Socket Head Cap Screw Model Numbers Japanese Standard "JIS" and N. American esign Standard Qty. uropean esign Standard SLHG- SLHG-6 SLHG- M6 Lg. M Lg. /- UNC -/ Lg. /-6 UNC -/ Lg. M 6 Lg. /- UNC -/ Lg. M 7 Lg. /- UNC Lg. 6 6 Tightening Torque Nm (In. lbs.) - (6-) -7 (-67) - (-9) 7- (6-77) - Pilot Connection T rain Connection -A Coil Type -C Manual Override -N lectrical Conduit Connection - esign Number esign Standards None: Internal Pilot : xternal Pilot None: xternal rain T: Internal rain AC: A A A A C: R: (AC C) R R None: Manual Override Pin C: Push Button & Lock Nut (Options) None: Terminal Box Type N: Plug-in Connector Type None: Japanese Std. "JIS" 9: N.American esign Std. None: Japanese Std. "JIS" & uropean esign Std. 9: N.American esign Std.. In case of lines with counterbalance function (- A A W, - W ), xternal rain must be selected for rain Connection. The coil type numbers in the shaded column are handled as optional extras. In case these coils are required to be chosen, please confirm the time of delivery with us before ordering. 6
Function and Purpose of Use Type of Pilot Model No. Graphic Symbols irectional Function Flow Pilot Operated Check Valve Pressure Purpose of Use Type "" SLHG- - b a # # # AB Functions as Three Position Four-Way Valve (Spring Centred Model). Type "" Type "" SLHG- - SLHG- - T A P B Y b a T A P B Y a b T A P B Y PT Position # # # ON OFF OFF OFF OFF ON # # # # AB PT Position # # # # ON OFF ON OFF OFF OFF ON ON A B irectional P T Both Metre-in and Metre-out are possible A B irectional P T To get a function of pilot operated check valve, the following conditions should be fulfilled. Internal pilot type ("P" port pressure) >= ("A""B" ports pressure) xternal pilot type (Pilot pressure) >= ("A""B" ports pressure) Functions as Three Position Four-Way Valve (Spring Centred Model) as well as Two Position Valve which uses positions # and #. ffective especially when the actuator has inertia force. Functions as Four Position Four-Way Valve. Regenerative circuit can be constructed at the Position #. Type "" SLHG- -A SLHG- -W b a T A P B Y b a T A P B Y # # # AB PT Position # # # ON OFF OFF OFF OFF ON A B irectional P T A B irectional P T A B irectional P T A B irectional P T Pressure control function (counterbalance valve) has been added to Type "" to make this type. Used to control the back pressure of the actuator. a b Type "" SLHG- -A SLHG- -W T A P B Y a b # # # # AB PT Position # # # # ON OFF ON OFF OFF OFF ON ON A B irectional P T A B irectional P T A B irectional P T A B irectional P T Pressure control function (counterbalance valve) has been added to Type "" to make this type. Used to control the back pressure of the actuator. T A P B Y 6
IRCTIONAL CONTROLS Instructions Pilot Pressure Pilot pressure of external pilot drain models must always exceed the pressure of the main pressure port "P". Pilot rain Port Avoid connecting the pilot drain port to a line with possible surge pressure. rain Connection when with Counterbalance Function When a valve having counterbalance function is used with internal drain type, the counterbalance pilot valve is subjected to pressure fluctuation and the pressure setting becomes unstable. For this reason, be sure to use external drain type valve. Flow Adjustment To perform the flow adjustment, loosen the lock nut, then turn the flow adjustment screw clockwise to decrease the flow. Be sure to re-tighten the lock nut after the adjustment. Pressure Adjustment To perform the pressure adjustment, loosen the lock nut, then turn the pressure adjustment screw clockwise to increase the pressure. Be sure to re-tighten the lock nut after the adjustment. Min. led Flow for Types "" and "A" at The Time of Metre-out Minimum controlled flow at the time of metre-out control is limited (this does not happen during metre-in control) as shown in the figure below only in the case of pilot control types "" (SLHG- -) and "A" (SLHG- -A). Min. led Flow for Types "" and "A" at The Time of Metre-out U.S.GPM L/min SLHG-- Min. Flow Rate SLHG-6- SLHG--, SLHG- 6-A SLHG--A 6 MPa ifferential Pressure PSI 6
Pressure rop Hydraulic Fluid: Viscosity m m /s (6 SSU), Specific Gravity. Pressure rop P PSI 7 SLHG- MPa.. P A, P B.6.. A T, B T 6 L /min Pressure rop P PSI 7 MPa...6.. SLHG-6 P A P B A T B T L /min Pressure rop P PSI 7 MPa...6.. SLHG- B T P A, P B A T L /min Flow Rate U.S.GPM 6 7 Flow Rate U.S.GPM 6 Flow Rate U.S.GPM For any other viscosity, multiply the factors in the table below. Viscosity Factor mm /s SSU 77. 9.7.96 6..9 6 7. 7.9 7. 9 7.7 6. For any other specific gravity (G'), the pressure drop ( P') may be obtained from the formula below. P'= P (G'/.) Flow vs. Adjustment Revolutions U.S.GPM Flow Rate L /min SLHG- P: ifferential Pres. P=MPa(PSI) P=() P=() 6 P=7() P=() P=.() 6 Fully Position Closed (Number of Turns) U.S.GPM Flow Rate 7 6 L /min SLHG-6 SLHG- P: ifferential Pres. U.S.GPM L /min P: ifferential Pres. P=MPa(PSI) P=() P=() P=7() P=() P=.() 6 Fully Closed Position (Number of Turns) Flow Rate 6 P= () P= () P=MPa(PSI) P=7() P=() P=.() 6 7 Fully Position Closed (Number of Turns) Minimum Adjustment Pressure Because the minimum adjustment pressure varies with the tank line back pressure, add the tank line back pressure to the value on the following lines. PSI MPa. SLHG-- PSI MPa. SLHG-6- PSI MPa. SLHG-- Min. Adj. Pressure.. 7 L /min Min. Adj. Pressure.. L /min Min. Adj. Pressure.. L /min Flow Rate U.S.GPM Flow Rate U.S.GPM 6 Flow Rate U.S.GPM 6
IRCTIONAL CONTROLS SLHG-- - -/9 Tank Port "T" Pressure Port "P" Terminal Box Type SLHG--- -/9 Mounting Surface: ISO -A-7--A Fully xtended 77(.9) Fully xtended.6(.) 96(.7).(.) Pilot Pressure Port "X" (For xternal Pilot Type only) (.) 69.9 (.7) 69.9 (.7) 9 (.) lectrical Conduit Connection "C" Thd. (Both nds) (.) 99(.9) (.9) (.) ia. Through 7.(.69) ia. Spotface Places Cylinder Port "A" (.97).6 (.6) Pilot rain Port "Y" 7(.) ia. Through (.) ia. Spotface Places (For xternal rain Type only) Cylinder Port "B" C/R :.(.) lectrical Conduit Connection AC : 96.(7.7) "C" Thd. (Both nds) 9(.7) C/R :.7(.) AC :.7(.) (.6) 7 (.7) 9. (7.6). (9.6). (.9) 7 (.6) (.) 6 (.) Manual Actuator 6(.) ia. SLHG-- - - SLHG-- - -9 6. (.) 6. (.7). (.9) For other dimensions, see "SLHG-- " drawing left. "C" Thd. G / / NPT Lock Nut 7(.67) Hex. (.) Hex. Soc. C. Mounting Surface (s Furnished) (.6) (.) ia. Two Locating Pins IMNSIONS IN MILLIMTRS (INCHS) SLHG--W- - -/9 SLHG--A- - -/9 Lock Nut (.) Hex. (.) Hex. Soc. INC. Lock Nut 7(.67) Hex. (.). (.) 6. (.6) 7. (.9) (.) Hex. Soc. C. Fully xtended 96(.7) Fully xtended.(.) For other dimensions, see "SLHG-- " drawing above. SLHG--W- - -/9 (.) 99(.9) (.9) 7 (.7) Fully xtended 77(.9) For other dimensions, see "SLHG--W" drawing left. SLHG--A- - -/9 Lock Nut (.) Hex. (.) Hex. Soc. INC. Lock Nut 7(.67) Hex. (.) Hex. Soc. C. Fully xtended 96(.7) Fully xtended.(.) For other dimensions, see "SLHG-- " drawing above. 6(.) 6. (.). (.) 6. (.7) Fully xtended 77(.9) For other dimensions, see "SLHG--W" drawing left. 6
SLHG-- - -N-/9 Plug-in Connector Type Mounting Surface: ISO -A-7--A Tank Port "T" Fully xtended 77(.9) Fully xtended.6(.) 96(.7). (.) Pressure Port "P" Pilot Pressure Port "X" (For xternal Pilot Type only) (.) ia. Through 7.(.69) ia. Spotface Places Cylinder Port "A" (.97) 7(.) ia. Through (.) ia. Spotface Places C/R :.(.) AC : 96.(7.7) (.) C (.) 69.9 (.7).6 (.6) 7. (.) 9(.) Pilot rain Port "Y" (For xternal rain Type only) Cylinder Port "B" C/R :.7(.) AC :.7(.) Cable eparture Cable Applicable: Outside ia.... - mm (. -.9 in.) Conductor Area... Not xceeding.mm (. sq. In) F The position of the Plug-in connector can be changed as illustrated left by loosening the lock nut. After completion of the change, be sure to tighten the lock nut with the torque as specified left. (.6) 7(.7) 9.(7.6) (.) Manual Actuator 6(.) ia. Lock Nut 7(.67) Hex. (.) Hex. Soc. C. Mounting Surface (s Furnished) (.6) (.) ia. Two Locating Pins SLHG-- -A -N SLHG-- - -N SLHG-- -R -N imensions mm (Inches) C F 9 (.) 9 (.) (.9) (.9) 6 (.) 7. (.).(.) 69.(.6) 7.(.7) 7. (.) 7. (.) (.) SLHG--- -N-/9 (.) 99(.9) (.9) 6. (.) SLHG---A -N SLHG--- -N SLHG---R -N imensions mm (Inches) (.9) 6 (.) 7. (.). (.) 9. (.) 99. (.6) For other dimensions, see "SLHG-- - -N" drawing above. IMNSIONS IN MILLIMTRS (INCHS) 66
IRCTIONAL CONTROLS Plug-in Connector Type Mounting Surface: ISO -A-7--A SLHG--W- - -N-/9 SLHG--A- - -N-/9 Lock Nut (.) Hex. (.) Hex. Soc. INC. Lock Nut 7(.67) Hex. (.) Hex. Soc. C. (.). (.) 7 (.7) Fully xtended 96(.7) Fully xtended.(.) Fully xtended 77(.9) SLHG--W- -A -N SLHG--W- - -N SLHG--W- -R -N imensions mm (Inches) (.9) 7. (.96) 6 (.) 9. (.) 7. (.) 9. (.) For other dimensions, see "SLHG--W- - -N" drawing left. For other dimensions, see SLHG-- - -N on the previous page. SLHG--W- - -N-/9 SLHG--A- - -N-/9 (.) 99(.9) (.9) Lock Nut (.) Hex. (.) Hex. Soc. INC. Lock Nut 7(.67) Hex. 6. (.) (.) Hex. Soc. C. 6 (.) Fully xtended 96(.7) Fully xtended.(.) Fully xtended 77(.9) SLHG--W- -A -N SLHG--W- - -N SLHG--W- -R -N imensions mm (Inches) (.9) 6. (.) 6 (.) 7. (.) 7. (.). (.) For other dimensions, see SLHG-- - -N on the previous page. For other dimensions, see "SLHG--W- - -N" drawing left. IMNSIONS IN MILLIMTRS (INCHS) 67
Tank Port "T" Fully xtended (.7) Fully xtended. 97.(.) (.). (.9) Pressure Port "P" Terminal Box Type SLHG-6- - -/9 SLHG-6-- -/9 Pilot rain Port "Y" (For xternal rain Type only) Mounting Surface: ISO-A---A lectrical Conduit Connection "C" Thd. (Both nds) 99(.9) (.) (.9) Pilot Pressure Port "X" (For xternal Pilot Type only).(.) ia. Through (.79) ia. Spotface 6 Places 77 (.) C/R :.(.) AC : 96.(7.7) 9(.7) Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. Cylinder Port "B" Cylinder Port "A" 6. (.) 9. (.6) (.6) lectrical Conduit Connection "C" Thd. (Both nds) C/R :.7(.) AC :.7(.) (.97) 9(.) Mounting Surface (s Furnished). (.6) 6. (.). (.7) 6 (.) Manual Actuator 6(.) ia. 7 (.6) 6(.) ia. Two Locating Pins (.6) 6 (.). (9.). (.6) 6. (.) For other dimensions, see "SLHG-6- " drawing left. "C" Thd. SLHG-6- - - G / SLHG-6- - -9 / NPT IMNSIONS IN MILLIMTRS (INCHS) SLHG-6-W- -/9 Lock Nut (.) Hex. (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. Fully xtended 9(.7) 6 (6.). (9.). (.6) 6. (.) SLHG-6-A- -/9 Fully xtended.(6.) SLHG-6-W- -/9 Lock Nut (.) Hex. For other dimensions, see "SLHG-6- " drawing above. Fully xtended 9(.7) (.) 99(.9) (.9) For other dimensions, see "SLHG-6-W" drawing left. SLHG-6-A- -/9 Fully xtended.(6.) (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. 6(6.) 96. (.67). (.) 6. (.) For other dimensions, see "SLHG-6- " drawing above. For other dimensions, see "SLHG-6-W" drawing left. 6
IRCTIONAL CONTROLS SLHG-6- - -N-/9 Tank Port "T" Fully xtended (.7) Fully xtended.(.) 97.(.). (.9) Plug-in Connector Type Pressure Port "P" Pilot rain Port "Y" (For xternal rain Type only) Mounting Surface: ISO-A---A Pilot Pressure Port "X " (For xternal Pilot Type only).(.) ia. Through (.79) ia. Spotface 6 Places 77 (.) C/R :.(.) AC : 96.(7.7) (.) C 6. (.) 9.(.6) Cylinder Port "B" Cylinder Port "A" C/R :.7(.) AC :.7(.) Cable eparture Cable Applicable: Outside ia.... - mm (. -.9 in.) Conductor Area... Not xceeding.mm (. sq. In) F Manual Actuator 6(.) ia. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. (.97) 9(.). (.6) 7 (.6) (.6) Mounting Surface (s Furnished) 6(.) ia. Two Locating Pins 6 (.) SLHG-6-- -N-/9 SLHG-6- -A -N SLHG-6- - -N SLHG-6- -R -N imensions mm (Inches) C F (.9). (.6) 6 (.) 9. (.9) 7. (.) 97. (.7) 9 (.) 9 (.) (.9) 7. (.) 7. (.) (.) Position of cable departure can be changed. For the details, refer to SLHG- valve on page 66. (.) 99(.9) (.9).(9.) SLHG-6--A -N SLHG-6-- -N SLHG-6--R -N imensions mm (Inches) (.9) 6 (.) 7. (.) 6. (.7) 7. (.). (.6) For other dimensions, see "SLHG-6- - -N" drawing above. IMNSIONS IN MILLIMTRS (INCHS) 69
Plug-in Connector Type Mounting Surface: ISO-A---A SLHG-6-W- -N-/9 SLHG-6-A- -N-/9 Fully xtended 9(.7) Fully xtended.(6.) Lock Nut (.) Hex. (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. 6 (6.). (9.) SLHG-6-W-A -N SLHG-6-W- -N SLHG-6-W-R -N imensions mm (Inches) (.9) 6 (.) 7. (.) 6. (.7) 7. (.). (.6) For other dimensions, see "SLHG-6-W- -N" drawing left. For other dimensions, see SLHG-6- - -N on the previous page. SLHG-6-W- -N-/9 SLHG-6-A- -N-/9 Fully xtended 9(.7) (.) 99(.9) (.9) Fully xtended.(6.) Lock Nut (.) Hex. (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. 6 (6.) 96. (.67) SLHG-6-W-A -N SLHG-6-W- -N SLHG-6-W-R -N imensions mm (Inches) (.9) 6. (.) 6 (.) 7. (.67) 7. (.) 7. (.7) For other dimensions, see SLHG-6- - -N on the previous page. For other dimensions, see "SLHG-6-W- -N" drawing left. IMNSIONS IN MILLIMTRS (INCHS) 7
IRCTIONAL CONTROLS Fully xtended (7.) Fully xtended 9.(7.) 6.7(.) 76.(.) Tank Port "T".(.) ia. Through (.6) ia. Spotface 6 Places Pilot Pressure Port "X" (For xternal Pilot Type only) 6(.) Hex. Soc. C. Lock Nut 9(.7) Hex.. (.) Pressure Port "P" 79. (.).(6.) Cylinder Port "B" Cylinder Port "A" Terminal Box Type Pilot rain Port "Y" (For xternal rain Type only) C/R :.(.) lectrical Conduit Connection AC : 96.(7.7) "C" Thd. (Both nds) 9(.7) C/R :.7(.) 6 AC :.7(.) (.) 7 (.) (.). (.). (.9). (.) (.77) 7 (.6) Manual Actuator 6(.) ia. Mounting Surface: ISO -AF---A SLHG-- - -/9 SLHG--- -/9 9(7.) lectrical Conduit Connection "C" Thd. (Both nds). (.). (.) SLHG-- - - SLHG-- - -9 7. (.7) (.) "C" Thd. G / / NPT 99(.9) (.9) For other dimensions, see "SLHG-- " drawing left Mounting Surface (s Furnished) 6 (.) 6(.) ia. Two Locating Pins IMNSIONS IN MILLIMTRS (INCHS) SLHG--W- -/9 SLHG--A- -/9 Lock Nut (.) Hex. (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. Fully xtended 9(.7) (9.). (.). (.) 7. (.7) Fully xtended.(6.) For other dimensions, see "SLHG-- " drawing above. For other dimensions, see "SLHG--W" drawing left. SLHG--W- -/9 Fully xtended 9(.7) 99(.9) (.) (.9) SLHG--A- -/9 Lock Nut (.) Hex. (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. (9.) 6. (.). (6.6). (6.) For other dimensions, see "SLHG-- " drawing above. For other dimensions, see "SLHG--W" drawing left. 7
SLHG-- - -N-/9 Fully xtended (7.) Fully xtended 9. (7.) Tank Port "T" 6.7(.) 76. (.) Plug-in Connector Type Pressure Port "P" Pilot rain Port "Y" (For xternal rain Type only) Mounting Surface: ISO -AF---A.(.) ia. Through (.6) ia. Spotface 6 Places Pilot Pressure Port "X" (For xternal Pilot Type only). (.) C/R :.(.) AC : 96.(7.7) (.) C Cylinder Port "B" Cylinder Port "A" Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. 7 (.) (.).(.) (.77) Manual Actuator 6(.) ia. Mounting Surface (s Furnished) 6 (.) 6(.) ia. Two Locating Pins SLHG-- -A -N SLHG-- - -N SLHG-- -R -N imensions mm (Inches) C F 9 (.) 9 (.) (.9) (.9) 6 (.) 7. (.) 7. (.) 7. (.) (.) 79. (.). (6.) 9 (7.) C/R :.7(.) AC :.7(.) Cable eparture Cable Applicable: Outside ia.... - mm (. -.9 in.) Conductor Area... Not xceeding. mm (. sq. in.) F 7 (.6) SLHG--- -N-/9. (.) 6. (.) 6. (.) Position of cable departure can be changed. For the details, refer to SLHG- valve on page 66. (.) 99 (.9) (.9). (.) SLHG---A -N SLHG--- -N SLHG---R -N imensions mm (Inches) (.9) 6 (.) 7. (.) 7. (.7). (.) 7. (.6) For other dimensions, see "SLHG-- - -N" drawing above. IMNSIONS IN MILLIMTRS (INCHS) 7
IRCTIONAL CONTROLS Plug-in Connector Type Mounting Surface: ISO -AF---A SLHG--W- -N-/9 SLHG--A- -N-/9 Fully xtended 9(.7) Fully xtended.(6.) Lock Nut (.) Hex. (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. (9.). (.) SLHG--W-A -N SLHG--W- -N SLHG--W-R -N imensions mm (Inches) (.9) 6 (.) 7. (.) 7. (.7). (.) 7. (.6) For other dimensions, see "SLHG--W- -N" drawing left. For other dimensions, see SLHG-- - -N on the previous page. SLHG--W- -N-/9 SLHG--A- -N-/9 Lock Nut (.) Hex. Fully xtended 9(.7) (.) 99 (.9) (.9) Fully xtended.(6.) (.) Hex. INC. Lock Nut 9(.7) Hex. 6(.) Hex. Soc. C. (9.) 6. (.) SLHG--W-A -N SLHG--W- -N SLHG--W-R -N imensions mm (Inches) (.9) 6 (.) 7. (.). (6.7) 9. (7.). (7.) For other dimensions, see "SLHG--W- -N" drawing left. For other dimensions, see SLHG-- - -N on the previous page. IMNSIONS IN MILLIMTRS (INCHS) 7
List of Seals for Main Valve, Pilot Selector Valve and Orifice SLHG-/6/- - -/9 Y Orifice for AT Orifice for PA 7 6 7 Z Orifice for BT Orifice for PB Section Y-Y Y Z Section Z-Z 9 6 6 7 6 7 9 SLHG-/6/-- -/9 6 Note) Main valve is same as above drawings. List of Seals for Main Valves Item 6 7 9 Name of Parts Back Up Ring Orifice Type SLHG- SLHG-6 SLHG- Part Numbers SLHG- SLHG-6 SLHG- SO-NB-P SO-NB-P SO-NB-P9 SO-NA-P SO-NB-P SO-BB-P SO-NB-G SO-NB-P SO-NB-P SO-NA-P SO-NB-P9 SO-BB-P SO-NB-G SO-NB-P SO-NB-P SO-NA-P6 SO-NB-P SO-BB-P6 Qty. Note: When ordering the seals, please specify the seal kit number listed on page 7. Item Orifice The timing of flow path opening/closing can be adjusted as required by selecting the appropriate pilot orifice diameter. When the diameter of the orifice is to be changed, another orifice should be ordered. Standard built-in orifice diameters and selectable orifice diameters are listed in the table below. TP-OPT-/6 x d Orifice iameter "d" mm Standard Max. ia. at Pressure Selectable Built-in over MPa(9 PSI)..,.6,.,....,.,.6,...,.. Item Pilot Selector Valve List Multi-Purpose Valve SLHG-- SLHG-- SLHG-- SLHG-6- SLHG-6- SLHG-6- SLHG-- SLHG-- SLHG-- Pilot Selector Valve CG--- CG--- CG--- CG-6-- CG-6-- CG-6-- CG-6-- CG-6-- CG-6-- Note: For details of Pilot Selector Valve, see page 76. Pilot Valve Refer to page 7 for Pilot Valve. 7
IRCTIONAL CONTROLS List of Seals for Main Valves and Pilot Selector Valve SLHG-/6/-W- -/9 6 7 W Z Orifice for AT Orifice for PA Orifice for BT Orifice for PB Section W-W 6 9 7 SLHG-/6/- A - -/9 A W 7 6 6 7 Z Section Z-Z 9 9 6 SLHG-/6/-W- -/9 6 List of Seals for Main Valves Item 9 6 Note : Name of Parts Back Up Ring The figures in ( A. 6 9 9 7 Part Numbers SLHG- SLHG-6 SLHG- SO-NB-P SO-NB-P SO-NB-P6 SO-NB-P SO-NB-P9 SO-NA-P SO-NB-P SO-BB-P SO-NB-G SO-NB-P SO-NB-P SO-NB-P SO-NB-P SO-NA-P SO-NB-P9 SO-BB-P Qty. SO-NB-G SO-NB-P SO-NB-P () SO-NB-A () SO-NB-P SO-NA-P6 () SO-NB-P SO-BB-P6 () ) indicate the quantity of seals used for A and Note : When ordering the seals, please specify the seal kit number listed on page 7. Pilot Valve Refer to page 7 for Pilot Valve. Note) Main valve is the same as above drawings. Pilot Selector Valve List Multi-Purpose Valve SLHG--A- SLHG--W- SLHG--A- SLHG--W- SLHG-6-A SLHG-6-W SLHG-6-A SLHG-6-W SLHG--A SLHG--W SLHG--A SLHG--W Pilot Selector Valve Item CG--A- - CG--W- - CG--A- - CG--W- - CG-6-A- CG-6-W- CG-6-A- CG-6-W- CG-6-A- CG-6-W- CG-6-A- CG-6-W- Item CG--- CG-6-- CG-6-- Note: Fill "B" or "H" representing the pressure adjustment range in section marked with. See page 77 for the details of the pilot selector valves. See the previous page for Item Orifice. 7
List of Seals (Pilot Selector Valves) CG-/6-- X X 7 6 7 9 Section X-X CG-/6-- X X 6 7 6 7 9 Section X-X CG-/6-- X X 6 7 9 6 Section X-X List of Seals CG- CG-6 Item Name of Parts Part Numbers Quantity CG-- CG-- CG-- Part Nmbers Quantity CG-6- CG-6- CG-6-6 7 SO-NB-P SO-NB-P SO-NB-P SO-NB-P 7 7 SO-NB-P SO-NB-P9 SO-NB-P SO-NB-A 7 7 Note: When ordering the o-rings, please specify the seal kit number listed in page 7. 76
IRCTIONAL CONTROLS List of Seals (Pilot Selector Valves) CG-/6-W- Y 9 6 7 9 9 7 Section Y-Y 6 7 Y 6 6 CG-/6-A- CG-/6-A- 6 6 CG-/6-W- Y Y 9 6 7 9 9 7 Section Y-Y Y Y List of Seals CG- CG-6 Item Name of Parts Part Numbers Quantity -W- -A- -W- -A- Part Nmbers Quantity -W- -A- -W- -A- 6 7 9 Back Up Ring SO-NB-P SO-NB-P9 SO-NB-P SO-NB-P SO-NA-P6 SO-NB-P SO-BB-P6 SO-NB-P6 SO-NB-P SO-NB-P SO-NB-P SO-NA-P9 SO-NB-P9 SO-BB-P9 Note: When ordering the seals, please specify the seal kit number listed in page 7. 77
List of Seal Kits and Pilot Valves SLHG--- - - SLHG--- - -9 SLHG--- - - SLHG--- - -9 SLHG--- - - SLHG--- - -9 SLHG--A- SLHG--A- SLHG--W- SLHG--W- SLHG--A- SLHG--A- SLHG--W- SLHG--W- - - - - - -9 - - - - - -9 - - - - - -9 - - - - - -9 SLHG-6-- - - SLHG-6-- - -9 SLHG-6-- - - SLHG-6-- - -9 SLHG-6-- - - SLHG-6-- - -9 SLHG-6-A- - - SLHG-6-A- - -9 SLHG-6-W- - - SLHG-6-W- - -9 SLHG-6-A- - - SLHG-6-A- - -9 SLHG-6-W- - - SLHG-6-W- - -9 SLHG--- - - SLHG--- - -9 SLHG--- - - SLHG--- - -9 SLHG--- - - SLHG--- - -9 SLHG--A- - - SLHG--A- - -9 SLHG--W- - - SLHG--W- - -9 SLHG--A- - - SLHG--A- - -9 SLHG--W- - - SLHG--W- - -9 Pilot Valve SG--C9- - -7 SG--C9- - -79 SG--C9- - -7 SG--C9- - -79 SG--B- - -7 SG--B- - -79 SG--C9- - -7 SG--C9- - -79 SG--C9- - -7 SG--C9- - -79 SG--B- - -7 SG--B- - -79 SG--B- - -7 SG--B- - -79 SG--C9- - -7 SG--C9- - -79 SG--C9- - -7 SG--C9- - -79 SG--B- - -7 SG--B- - -79 SG--C9- - -7 SG--C9- - -79 SG--C9- - -7 SG--C9- - -79 SG--B- - -7 SG--B- - -79 SG--B- - -7 SG--B- - -79 SG--C9- - -7 SG--C9- - -79 SG--C9- - -7 SG--C9- - -79 SG--B- - -7 SG--B- - -79 SG--C9- - -7 SG--C9- - -79 SG--C9- - -7 SG--C9- - -79 SG--B- - -7 SG--B- - -79 SG--B- - -7 SG--B- - -79 Complete Kit KS-SLHG--- - KS-SLHG--- - KS-SLHG--- - KS-SLHG--A- - KS-SLHG--W- - KS-SLHG--A- - KS-SLHG--W- - KS-SLHG-6-- - KS-SLHG-6-- - KS-SLHG-6-- - KS-SLHG-6-A- - KS-SLHG-6-W- - KS-SLHG-6-A- - KS-SLHG-6-W- - KS-SLHG--- - KS-SLHG--- - KS-SLHG--- - KS-SLHG--A- - KS-SLHG--W- - KS-SLHG--A- - KS-SLHG--W- - Seal Kit Numbers For Pilot Selector Valves KS-CG--- KS-CG--- KS-CG--A- KS-CG--W- KS-CG--A- KS-CG--W- KS-CG-6-- KS-CG-6-- KS-CG-6-- KS-CG-6-A- KS-CG-6-W- KS-CG-6-A- KS-CG-6-W- KS-CG-6-- KS-CG-6-- KS-CG-6-- KS-CG-6-A- KS-CG-6-W- KS-CG-6-A- KS-CG-6-W- For Pilot Valves KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) KS-SG-- -7 ( Set Req'd) Note : Fill coil type (a symbol representing current/voltage) in section marked. Likewise, in section marked, fill a symbol representing the type of electrical conduit connection (None: Terminal Box Type, N: Plug-in Connector Type). : A complete seal kit is composed of seal kit for pilot selector valve, seal kit for pilot valve and seal for main valve. See pages 7 and 7 for information on the seals for main valve. : See page for the detailed information on the pilot valves. 7
IRCTIONAL CONTROLS How to Change Pilot & rain Connection Pilot Connectio n and rain Connectio n can be changed easily with a disconnection/connectio n of pilot plug. The following drawings give illustrations of xternal Pilot-xternal rain Type, When changing to Internal Pilot-Internal rain Type, the following procedure may be followed. xternal Pilot Internal Pilot (See Section -) ) Remove pipe plug. ) Remove pipe plug. ) Wind a sealing tape around the pipe plug the port., then fit the plug into xternal rain Internal rain (See Section -) ) Remove pipe plug. ) Remove pipe plug. ) Wind a sealing tape around the pipe plug, then fit the plug into the port. ) In case of SLHG-, fit the plug into the port "Y" on the sub-plate. In case of SLHG-6/, wind a sealing tape around the plug and then thread it into the port "Y". SLHG- Pipe Plug Pipe Plug for rain Connection Selection Pipe Plug for Pilot Connection Selection Pipe Plug Section - Section - SLHG-6/ Pipe Plug for Pipe Plug for Pilot Connection rain Connection Selection Selection Pipe Plug Pipe Plug Thread "Y" Section - Section - 79