V50,,F,G,H, Single-Seated Valves FETURES Sizes range from one-half inch to six inches. vailable with threaded or flanged pipe connections. Direct- or reverse-acting models. Valve designs provide equal percentage flow characteristic for close control of water and glycol solutions, and linear flow characteristic for close control of steam. Spring-loaded, self-adjusting packing. Stainless steel stem prevents corrosion that could damage the packing. PPLTON V50G Models available with metal-to-metal seating for high differential pressure applications. The V50 is a single-seated valve for control of steam, water, and glycol solutions (up to 50% concentration) in heating or air conditioning applications. These valves are used in two-position and modulating control systems. These valves are not suitable for combustible gas service. ontents pplication... Features... Specifications... Ordering nformation... nstallation... 7 heckout... 8 U.S. Registered Trademark opyright 998 Honeywell nc. ll rights Reserved 60-6- 3
SPEFTONS MPORTNT The specifications given in this publication do not include normal manufacturing tolerances. Therefore, an individual unit may not exactly match the listed specifications. lso, this product is tested and calibrated under closely controlled conditions and some minor differences in performance can be expected if those conditions are changed. TRDELNE Models TRDELNE models are selected and packaged for ease of handling, ease of stocking, and maximum replacement value. TRDELNE model specifications are the same as those of standard models except as noted. TRDELNE Model vailable: V50F Valve: Single-seated valve for water, glycol, or twoposition steam. Throttling plug provides equal percentage flow characteristic. Not recommended for modulating steam. Push stem down to close valve. Service Temperature Range: 45 to 50 F (4 to ). Pipe onnections: Threaded connections. Valve Disc: PTFE disc with removable throttling plug. dditional Features TRDELNE pack with cross reference label and special instructions. Standard Models Models: V50 Valve: Single-seated valve for water, glycol, or two-position steam. Throttling plug provides equal percentage characteristic of flow. Push down valve stem to close. Flanged pipe connections. Refer to Table. Valve Sizes and Flow apacities: See Table. V50 Valve: Single-seated valve for water, glycol, or two-position steam. Throttling plug provides equal percentage characteristic of flow. Not recommended for modulating steam. Push down valve stem to open valve (reverse acting). Flanged pipe connections. Refer to Table. V50G Valve: Single-seated valve for modulating steam; also suitable for two-position steam. Throttling plug provides linear characteristic of flow. Push down valve stem to close valve. Threaded pipe connections. Refer to Table. V50H Valve: Single-seated valve for water, glycol, or two-position steam. Throttling plug provides equal percentage characteristic of flow. Not recommended for modulating steam. Push down valve stem to open valve (reverse acting). Threaded pipe connections. Refer to Table. V50 Valve: Single-seated valve for modulating steam; also suitable for two-position steam. Throttling plug provides linear characteristic of flow. Push down valve stem to open valve (reverse acting). Threaded pipe connection. Refer to Table. ORDERNG NFORMTON When purchasing replacement and modernization products from your TRDELNE wholesaler or distributor, refer to the TRDELNE atalog or price sheets for complete ordering number. f you have additional questions, need further information, or would like to comment on our products or services, please write or phone:. Your local Home and uilding ontrol Sales Office (check white pages of your phone directory).. Home and uilding ontrol ustomer Relations Honeywell, 885 Douglas Drive North Minneapolis, Minnesota 554-4386 n anada Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, North York Ontario MV 4Z9. nternational Sales and Service Offices in all principal cities of the world. Manufacturing in ustralia, anada, Finland, France, Germany, apan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.. 60-6 3
Pipe onnections: / to 3 in. valves have threaded connections; -/ to 6 in. valves have flanged connections. Seat: rass: Removable, on threaded models (except V50H,). Stainless Steel: Removable on metal-to-metal seating V50G. ronze: Removable on flanged models. NS ody lass: 50 psi on threaded connection models; 5 psi on flanged connection models. Stem: Stainless steel. Disc: Teflon discs with removable throttling plugs; some models of the V50G have a metal-to-metal valve disc for high pressure applications. Stroke: / to 3 in. valves: 3/4 in.; 4 to 6 in. valves: -/ in. Pattern: Straight-through. ody Material: ronze: Threaded connection models. ast ron: Flanged connection models. Packing: Spring-loaded, self-adjusting: Teflon/rubber : V50F,H. Teflon cone: V50,,G,. Pressure-Temperature ody Ratings: See Fig.. SYSTEM PRESSURE (PS) 300 50 00 50 00 50 0 F 00 psi V50F, H (THREDED) NS LSS 50 (WTER) V50, (FLNGED) NS LSS 5 (WTER) 40 00 50 00 50 300 350 FLUD TEMPERTURE ( F) NOTES:.. V50G, (THREDED) NS LSS 50 (STEM) 40 F 337 F FOR HETNG FLUD TEMPERTURES, THE VLVE ND/OR PPNG SHOULD E NSULTED TO PREVENT MENT TEMPERTURES FROM EXEEDNG TUTOR RTNGS. FOR MXMUM TEMPERTURE DFFERENTL N LTERNTE HOT-OLD WTER, USE: 40 F. Fig.. Valve pressure/temperature ratings. M3976 Valve Flow haracteristics: Equal Percentage Flow haracteristics: Equal movements of the valve stem at any point of the flow range change the existing flow by a constant percentage, regardless of the quantity of flow. Used in water coil applications. See Fig.. Linear Flow haracteristics: Equal valve stem movements produce equal flow (volume) changes, regardless of the percentage of valve opening. n actual operation, characteristic is a modified linear action to improve control at low flow rates. Used in steam coil applications. See Fig.. PERENTGE STEM TRVEL 00 90 80 70 60 50 40 30 0 0 FLOW HRTERSTS EQUL PERENTGE LNER 0 0 0 30 40 50 60 70 80 90 00 PERENTGE FLOW M3975 Fig.. Equal percentage and linear flow characteristics. lose-off Pressure Rating: Depends on valve size and actuator used. See Valve Selection Guide, form 63-8038. Maximum Pressure Differential for Quiet Water Service: 0 psi. Maximum Pressure Drop for Normal Seat and Disc Life: Metal-to-metal Disc, Steam Service: 00 psi drop. Not recommended for water service. PTFE and omposition Disc: Two-position pplications: Steam Service 70 psi; water service 50 psi. Modulating pplications: Steam Service 35 psi; water service 5 psi. ody Marking: rrows on both sides of valve to show direction of flow. Packing Limits: Water Service V50F,H: 50 psi maximum pressure; 40 to 50 F temperature range. V50,: 50 psi maximum pressure; 40 to 40 F temperature range. Steam Service V50G,: 00 psi maximum pressure; 337 F maximum temperature. lternating Hot and old Water Service: 40 F maximum temperature difference (also see Fig. for body pressure-temperature limits). 3 60-6 3
Table. Valve Sizes, Flow apacities, Temperature and Pressure Ratings. Valve ody Disc Pipe Pipe Size Flow apacity Model Number Material onnections (in.) (v) V50 (Equal Percentage Flow haracteristic). omposition Flanged -/ 63.0 Stem down to close. 3 00.0 4 60.0 5 50.0 6 360.0 V50 (Equal Percentage Flow haracteristic). omposition Flanged 4 60.0 Stem up to close. 5 50.0 6 360.0 V50F (Equal Percentage Flow haracteristic). omposition Threaded / 0.63 Stem down to close..0.6.5 4.0 3/4 6.3 0.0 -/4 6.0 -/ 5.0 40.0 -/ 63.0 3 00.0 V50G (Linear Flow haracteristic). Stem down to close. omposition Threaded 40.0 -/ 63.0 3 00.0 Metal-to Threaded / 0.40 Metala 0.63.0.6.5 4.0 3/4 6.3 0.0 -/4 6.0 -/ 5.0 V50H (Equal Percentage Flow haracteristic). omposition Threaded /.5 Stem up to close. 4.0 3/4 6.3 0.0 -/4 6.0 V50 (Linear Flow haracteristic). Stem up to close. omposition Threaded /.5 4.0 3/4 6.3 0.0 -/4 6.0 astainless steel seats and trim. For modulating steam service. Not recommended for modulating water service 60-6 3 4
Dimensions: See Fig. 3 through 7. Motor nd Linkage Selection: Refer to Valve Selection Guide, form 63-8038. ccessories: Rebuild Kits (for threaded V50,,F,G Valves only): For Water Service: 400694-006 For / in. valves. 400695-006 For 3/4 in. and in. valves. 400309-006 For -/4 in. valves. 40030-006 For -/ in. valves. 4003-006 For in., -/ in., and 3 in. valves. For Steam Service: 400694-008 For / in. valves. 400695-008 For 3/4 in. and in. valves. 400309-008 For -/4 in. valves. 40030-008 For -/ in. valves. 4003-008 TRDELNE Kit for in., -/ in., and 3 in. valves. Repack Kits: For Water Service: 400394-004 TRDELNE Kit for / in., 3/4 in., in. and -/4 in. threaded V50,,F,G and all V50H, Valves. 400395-004 For -/ in., in., -/ in. and 3 in. threaded V50,,F,G and -/ in. and 3 in. flanged V50 Valves. 400396-00 For 4 in., 5 in., and 6 in. flanged V50, Valves. For Steam Service: 400394-00 For / in., 3/4 in., in. and -/4 in. threaded V50,,F,G and all V50H, Valves. 400395-00 For -/ in., in., -/ in. and 3 in. threaded V50,,F,G and -/ in. and 3 in. flanged V50 Valves. 400396-00 For 4 in., 5 in., and 6 in. flanged V50, Valves. Replacement Discs: For Threaded Valves: 400465-00 For / in. V50,F Valves. 400465-00 For 3/4 in. and in. V50,F Valves. 400465-003 For -/4 in. V50,F Valves. 400465-004 For -/ in. V50,F Valves. 400465-005 For in. V50,F Valves. 400465-006 For -/ in. V50,F Valves. 400465-007 For 3 in. V50,F Valves. 400465-0 For / in. V50,G Valves. 400465-0 For 3/4 in. and in. V50,G Valves. 400465-03 For -/4 in. V50,G Valves. 400465-04 For -/ in. V50,G Valves. 400465-05 For in. V50,G Valves. 400465-06 For -/ in. V50,G Valves. 400465-07 For 3 in. V50,G Valves. For Flanged Valves: 3004049-835 For -/ in. V50 Valves. 3004050-835 For 3 in. V50 Valves. NOTES: To rebuild a -/ in. or 3 in. threaded valve, order the replacement discs in addition to the rebuild kit. Rebuild kits are not available for Flange valves or reverse acting valves. D E Fig. 3. V50F,G threaded, / to 3 in. body dimensions. See Table. D Fig. 4. V50 flanged, -/ and 3 in. body dimensions. See Table. D H H G G H F M397 F E M9000 F E M3969 Fig. 5. V50 flanged, 4, 5 and 6 in. body dimensions. See Table. 5 60-6 3
H G E 4/8 (05) WTH STEM UP F SE OF TUTOR D M3970 Fig. 6. V50 flanged, 4, 5 and 6 in. body dimensions. See Table. -3/8 NH [35 MM] DMETER ONNET SZE. M397 Fig. 7. V50H, threaded, reverse acting body dimensions. See Table. Table. Valve Dimensions for Fig. 3 Through 7. ody Style Dimensions (in in.) and Figure Reference Size (in) a D E F G H (Travel) (Diameter) V50 -/ 3-/ 4-3/6 4 9-/ 7 -/ 3/4 5-/ 3/4-3/8 Flanged Direct ody (Fig. 4) 3 3-/ 5-3/8 4-5/8 7-/ 3 3/4 6 3/4-3/8 V50 4 5-/4 7-9/6 5-3/6 3 9 4 3/4 7-/ -/ -7/8 Flanged Direct ody (Fig. 5) 5 5-/4 7 6-/8 5 0 5 7/8 8-/ -/ -7/8 6 5-/4 8 7-/6 6-/ 6 7/8 9-/ -/ -7/8 V50 4 6-3/4 4-/6 8-/6 3 9 4 3/4 7-/ -/ -7/8 Flanged Reverse 5 6-3/4 5-5/8 7-/ 5 0 5 7/8 8-/ -/ -7/8 ody (Fig. 6) 6 6-3/4 6-9/6 8-/ 6-/ 6 7/8 9-/ -/ -7/8 V50F,G / 3-/ -3/4 -/6 -/6 5-/ 3/4-3/8 Threaded, 3/4 3-/ -3/4-3/4 -/6 -/6 5-/4 3/4-3/8 Direct ody 3-/ -7/8-5/8 -/8 -/8 -/8 5-3/8 3/4-3/8 (Fig. 3) -/4 3-/ -/ -7/6-7/6-3/4 5-/ 3/4-3/8 -/ 3-/ -7/8-3/8-3/6-3/6 3-/ 6-3/8 3/4-3/8 3-/ 3-/8-3/6-3/6 3-/ 6-5/8 3/4-3/8 -/ 3-/ -3/4-3/8 3-3/4 3-3/4 4-3/8 6-/4 3/4-3/8 3 3-/ 3-/8-3/8 4-7/6 4-7/6 5-/8 6-5/8 3/4-3/8 V50H, / -3/4 -/4 3-/ Threaded, Reverse 3/4-3/4 -/4 3-3/8 ody (Fig. 7) -7/8-5/6 3-7/8 -/4-3/6 4-/4 a Dimension is with the valve closed (stem down for the V50,F,G; stem up for the V50). 60-6 3 6
NSTLLTON When nstalling this Product. Read these instructions carefully. Failure to follow them could damage the product or cause a hazardous condition.. heck the ratings given in the instructions and on the product to make sure the product is suitable for your application. 3. nstaller must be a trained, experienced service technician. 4. fter installation is complete, check out product operation as provided in these instructions. PPE SZE (NHES) / 3/4 -/4 -/ EFFETVE LENGTH OF THREDS (NHES) [MLLMETERS] / [.7] 9/6 [4.3] /6 [7.5] /6 [7.5] /6 [7.5] 3/4 [9.] 3 MPORTNT Mount valve so fluid flows in the direction of the arrow cast on the valve body. Location Select a location where the valve, linkage, and motor will be within the ambient pressure and temperature ratings. For installation of the linkage and motor and to provide room for servicing the valve body, leave approximately a 0 inch clearance above the valve. (The valve body should be completely installed in the pipe line before the motor and linkage are installed.) When selecting a location for the valve, remember that most Modutrol V Motors mount with the motor shaft horizontal. Mounting The preferred mounting position of the valve is with the stem vertical. void mounting the valve with the stem below the horizontal. Scale and foreign material might collect and tend to score the stem and cause packing leakage. Protect the stem from damage due to bending or scratching. 3 USE PROPERLY REMED ND LENED PPE ND MODERTE MOUNT OF DOPE (LEVE TWO THREDS RE). VSE GRPS HEX END NEXT TO PPE (DO NOT TWST OR SQUEEZE VLVE ODY). VSE HOLDS PPE SEURELY GNST TURNNG ND PRLLED W WRENH GRPS VLVE HEX FLTS NEXT TO PPE. M763 Fig. 8. nstalling valves with threaded connections. Flanged Valve odies Flanged valve bodies conform to the merican Standard for ast-iron Pipe Flanges and Flanged Fittings. The valve flanges are flat-faced with a smooth finish. ompanion flanges must be of the same specifications. See Fig. 9. 3 Threaded Valve odies Threaded body threads conform to merican Standard Taper Pipe Threads (NPT). Squarely align the pipes with the valve at each end connection. f the pipes are forced into the valve, the body may become twisted and improper seating will result. Sparingly apply pipe dope. Take care to prevent pipe chips, scale, etc., from entering the piping because this material may lodge in the seat and prevent proper closing. Refer to the table in Fig. 8 for valve pipe sizes and thread lengths. This figure also shows two effective methods of holding the valve and pipe when attaching it. The valve will not function properly if it is twisted or squeezed during installation. 3 DO NOT PPLY PPE DOPE TO VLVE FLNGE, OMPNON FLNGE OR GSKET. E SURE FE OF OMPNON FLNGE S FLUSH WTH FE OF VLVE-ODY FLNGE ND LGNED SQURELY EFORE TGHTENNG MOUNTNG NUTS. F POSSLE, MOUNT OMPNON FLNGE ON PPE EFORE MOUNTNG FLNGE ON THE VLVE. M764 Fig. 9. Proper flange mounting. 7 60-6 3
Mounting bolts must be long enough to allow the nuts to utilize full length of the nut threads. To allow clearance for installing, the bolts should be /8 inch smaller than the diameter of the bolt hole. To prevent leakage, use a gasket material recommended for the medium to be handled. Refer to installation information furnished with the linkage and motor when installing these controls. HEKOUT efore installing linkage and motor, make sure that the valve stem operates freely. mpaired stem operation may indicate that the body was twisted by faulty piping or that the stem was bent by rough handling. Either of these conditions may require replacement of the valve. heck the valve body and connections for leaks. fter installing linkage and motor, check the operation according to the installation information furnished with these controls. Operate the system through one complete cycle to make certain that the valve controls properly. y using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys fees, arising out of, or resulting from, any modification to the literature by you. Home and uilding ontrol Home and uilding ontrol Honeywell sia Pacific nc. Honeywell nc. Honeywell Limited-Honeywell Limitee Room 33-35 Honeywell Plaza 55 Gordon aker Road Sun Hung Kai entre P.O. ox 54 North York, Ontario No. 30 Harbour Road Minneapolis, MN 55408-054 MH 3N7 Wanchai Hong Kong Honeywell Latin merican Region Honeywell Europe S.. 480 Sawgrass orporate Parkway 3 venue du ourget Suite 00 40 russels Sunrise, FL 3335 elgium 60-6 3.. Rev. -98 Printed in U.S.. on recycled paper containing at least 0% post-consumer paper fibers. www.honeywell.com/building/components