Operation is similar to standard centrifugal pumps, except the impeller is driven with a magnetic coupling, eliminating the need for a shaft seal. Magnetic drive pumps must be used where flooded suction exists. Typical applications include film processors; laser and x-ray cooling systems; medical, scientific and laboratory equipment and silver recovery equipment. Features: Corrosion resistant Limited dry run capability Hydraulically efficient Quiet operation No shaft seals Flexible mounting and body discharge positions Low current draw and heat rise NSF certified models available Contents Magnetic Drive Pump Overview... 2 OEM Options... 3 Series Comparison Chart... 3 14110 Series... 4-5 14520 Series... 6-7 15651 Series... 8-10 17650 Series... 11-12 INTG3 Series... 14-15 INTG7 Series... 16-17 Replacement Kits... 18-19 Gorman-Rupp Industries designs and manufactures pumps and pumping solutions for the Original Equipment Manufacturer (OEM). All series/models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. SERIES MAX FLOW MAX HEAD MAX SYSTEM PRESSURE MAX FLUID TEMPERATURE MOTOR SPECS / VOLTAGES 14110 11 GPM 16 FT 25 PSI 180 F (82 C) 115, 230, 50/60 Hz 14520 26 GPM 35 FT 75 PSI 203 F (95 C) 115, 230, 50/60 Hz 15651 3.75 GPM 13 FT 75 PSI 203 F (95 C) 115, 230, 50/60 Hz 17650 10.5 GPM 57 FT 75 PSI 160 F (71 C) 115, 230, 50/60 Hz 12, 24 DC Brushless INTG3 7.89 GPM 54 FT 75 PSI 203 F (95 C) 9-24 DC Integrated Brushless INTG7 20 GPM 93 FT 75 PSI 203 F (95 C) 12-30 DC Integrated Brushless GRI Overview 0518 050818 Page 1
Overview Magnetic drive centrifugal pump operation is similar to a standard centrifugal pump except the motor shaft seal is eliminated. Magnetic drive pumps are designed to isolate the pump body from the motor by driving an impeller and magnet assembly with a drive magnet attached to the motor shaft. Motor torque is transmitted by a drive magnet through a plastic housing to the impeller assembly. The plastic housing separates the motor drive magnet from the fluid being pumped. Leaks caused by shaft seal failure are eliminated. The end result is a more efficient seal-less centrifugal pump that will not leak and is capable of achieving up to 50 thousand hours of continuous duty operation. To handle the most aggressive chemicals, GRI s material of construction consists of special combinations of chemically inert plastic. The impeller shaft and bearing system handle the inherent friction and motor heat with built-in cooling passages that are designed to use the pumped liquid as a lubricating coolant. GRI uses ceramic shafts with either Teflon or ceramic thrust bearings as standard materials for each magnetic drive pump line. These robust features add tremendously to the chemical compatibility and overall life of the pump to make it virtually maintenance free. Impellers and pump bodies are designed to produce efficient flow and head characteristics required in today s applications. The hydraulic designs, coupled with motors specifically designed for the pump end, means less power consumption for the work performed. Typical OEM applications include film processors, laser and x-ray cooling systems, medical, scientific, laboratory and silver recovery equipment. Magnetic drive centrifugal pumps must be used where flooded suction conditions exist. Pump Specifications: Flow Rates: Range to 35 gpm (132 lpm) Max. Discharge Head: Range to 53 feet (16 m) Max. Fluid Temperature: Up to 250 F (121 C) Motors: All motors, except the 15651 series and 18650 series motors which use sleeve bearings, have sealed electric motor grade ball bearings, are thermally protected, class B insulated, and continuous duty rated. Most pumps available with AC or DC motors. Please contact GRI for questions regarding chemical compatibility. ADAPTER DISK MOTOR ADAPTER O-RING PUMP SHAFT BODY FRONT THRUST BEARING IMPELLER & MAGNET ASSEMBLY MAGNET & DRIVE HUB ASSEMBLY MOTOR GRI Overview 0518 050818 Page 2
OEM Options OEM Options: GRI specializes in the custom design and manufacturing of fluid pumps for the OEM market. Please contact us to discuss your project s needs and specifications. Body NSF certified models available Multiple suctions and discharge port configurations available. O-Rings (Elastomers) Flurosilicone (14110 & 14518/20 Series only) Kel-F Nitrile Neoprene Silicone Viton /Fluoroelastomer Agency Approvals (contact GRI) UL778: Motor-operated Water Pumps NSF 61: Potable Water NSF 372: Lead Content NSF 169: Special Purpose Food Equipment and Devices Compliances RoHS 2 (2011/65/EC) REACH (SVHC) Motors 115V, 50/60 Hz 115V/230V, 50/60 Hz Capacitor start, drip-proof, ball bearing, thermally protected 115V, 50/60Hz; 230, 50/60 Hz Explosion-proof (14520 Series only) 115V, 50/60 Hz; 230V, 50/60 Hz Open, shaded pole 115V, 50/60Hz; 230V, 50/60 Hz Open, shaded pole, impedance protected, ball bearing 230V, 50/60 Hz 12, 24 Brushless DC (BLDC) Drip-proof, shaded pole, thermally protected TEFC/PSC, thermally protected GRI Overview 0518 050818 Page 3
14110 Series Specifications Max Flow: 11 gpm Max Head: 16 ft Max System Pressure: 25 psi Max Fluid Temp. 180 F (82 C) Materials in contact with solution / OEM options Body Ryton Impeller Ryton with Epoxy adhesive Adaptor Ryton Pump Shaft Ceramic Impeller Bearings Resin Impregnated Carbon Front Thrust Bearings Glass-Filled Teflon Rear Thrust Bearings Ceramic O-Rings (Elastomers) EPT/EPDM Viton /Fluoroelastomer Nitrile Neoprene Silicone Kel-F Motor specifications / OEM options Motor Specs 115V, 50/60 hz 230V, 50/60 hz Vented Shaded pole Thermally protected Tefc/psa Features Corrosion Resistant Quiet operation Hydraulically efficient Flexible mounting and body discharge positions No shaft seals NSF certified models available Low current draw and heat rise Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. GRI Overview 0518 050818 Page 4
14110 Series GRI designs and manufactures pumps and pumping solutions for the Original Equipment Market (OEM). All models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. Model Number Voltage (Type) Amps Body Material O-Ring Material Connections Inlet/Outlet (inches) Curve (50Hz/60Hz) 14110-050 115 2.0 / 1.6 Ryton EPT/EPDM 3/4 MPT / 1/2 MPT B / A 14110-051 115 2.0 / 1.6 Ryton Viton /FKM 3/4 MPT / 1/2 MPT B / A 14110-052 230 1.0 /.80 Ryton EPT/EPDM 3/4 MPT / 1/2 MPT B / A 14110-053 230 1.0 /.80 Ryton Viton /FKM 3/4 MPT / 1/2 MPT B / A Performance at 50 Hz will be approximately 83% of the performance at 60 Hz. FKM = Fluoroelastomer, FPT = Female Pipe Thread, MPT = Male Pipe Thread, MHB = Male Hose Barb. 1.91 (48.51) 4.14 (105.16).99 (25.15) 1/2-14 N.P.T. (12.7 N.P.T.) Typical Dimensions 1.56 (39.62) 4.75 (120.65) FLOW 2.50 (63.50) 3.25 (82.55) Dimensions in Inches (Dimensions in Millimeters) 2.25 (57.15) 3/4-14 N.P.T. (19.05 N.P.T.).281 X.656 (7.14 X 16.66) 4-SLOTS 4.31 (109.47) 2.38 (60.45) 7.62 (193.63) GRI Overview 0518 050818 Page 5
14520 Series Specifications Max Flow 26 gpm Max Head 35 ft Max System Pressure 75 psi Max Fluid Temp. 203 F (95 C) Materials in contact with solution / OEM options Body Ryton Impeller Ryton with Epoxy adhesive Adaptor Ryton Pump Shaft Ceramic Impeller Bearings Resin Impregnated Carbon Front Thrust Bearings Glass-Filled Teflon Rear Thrust Bearings Ceramic O-Rings (Elastomers) EPT/EPDM Viton /Fluoroelastomer Nitrile Neoprene Silicone Kel-F TOTAL HEAD - FEET 35 30 25 20 15 10 5 0 LITERS PER MINUTE 0 20 40 60 80 100 A - 60 Hz curve. B - 50 Hz curve. C A B 0 5 10 15 20 25 30 U.S. GALLONS PER MINUTE 10.0 8.0 6.0 4.0 2.0 0 TOTAL HEAD - METERS Motor specifications / OEM options Motor Specs Features Corrosion Resistant Hydraulically efficient No shaft seals Low current draw and heat rise 115V, 50/60 hz 230V, 50/60 hz Vented Shaded pole Thermally protected Tefc/psa Quiet operation Flexible mounting and body discharge positions NSF certified models available Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. GRI Overview 0518 050818 Page 6
14520 Series GRI designs and manufactures pumps and pumping solutions for the Original Equipment Market (OEM). All models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. Model Number Voltage (Type) Amps Body Material O-Ring Material Connections Inlet/Outlet (inches) Curve (50Hz/60Hz) 14520-050 115V AC 2.4 / 2.0 Ryton EPT/EPDM 1 FPT x 3/4 MPT B / A (TEFC) 14520-051 115V AC 2.4 / 2.0 Ryton Viton /FKM 1 FPT x 3/4 MPT B / A (TEFC) 14520-052 230V AC 1.06 Ryton EPT/EPDM 1 FPT x 3/4 MPT B / A (TEFC) 14520-053 230V AC 1.06 Ryton Viton /FKM 1 FPT x 3/4 MPT B / A (TEFC) 14520-054 24V BLDC 8.3 Ryton EPT/EPDM 1 FPT x 3/4 MPT C (TENV) 14520-055 24V BLDC (TENV) 8.3 Ryton Viton /FKM 1 FPT x 3/4 MPT C Vectra is chemically resistant to most acids, oxidants and bleaches, and organic solvents. (Do not use with chemicals which are bases.) BLDC = Brushless DC. HS = High Speed. Performance at 50 Hz will be approximately 83% of the performance at 60 Hz. FKM = Fluoroelastomer, FPT = Female Pipe Thread, MPT = Male Pipe Thread, MHB = Male Hose Barb. 5.79 (147.07) 3.48 (88.39) 1.09 (27.69) 3/4" N.P.T. (19.05 N.P.T.) Typical Dimensions 2.06 (52.32) 5.13 (130.30) FLOW 3.91 DIA. (99.31) 4.21 (106.93) 2.50 (63.50) 2.74 (69.60) Dimensions in Inches (Dimensions in Millimeters) 2.25 (57.15) 1" N.P.T. (25.4 N.P.T.).281 X.656 (7.14 X 16.66) 4-SLOTS 6.39 (162.31) 10.06 (255.52) 2.38 (60.45) GRI Overview 0518 050818 Page 7
15651 Series Specifications LITERS PER MINUTE Max Flow 3.75 gpm 0 3 6 9 12 15 18 21 Max Head 13 ft 16.0 4.5 Max System Pressure 75 psi Max Fluid Temp. 203 F (95 C) 14.5 4.0 Materials in contact with solution / OEM options Body Vectra, Noryl 13.0 3.5 Impeller Vectra Bearings Vectra Pump Shaft Ceramic Thrust Bearings Glass-Filled Teflon O-Rings (Elastomers) EPT/EPDM Viton /Fluoroelastomer Nitrile Neoprene Silicone Kel-F Motor specifications / OEM options Motor Specs 115V, 50/60 Hz 230V, 50/60 Hz Open, Shaded Pole, Impedance Protected, Sleeve Bearing 12Vdc TOTAL HEAD - FEET 11.5 9.0 7.5 6.0 4.5 3.0 1.5 0 D C B A 0 1 2 3 4 5 6 U.S. GALLONS PER MINUTE A - 60 Hz curve. B - 50 Hz curve. C - 12VDC curve. D - 12V BLDC curve. 3.0 2.5 2.0 1.5 1.0.5 0 TOTAL HEAD - METERS Features Corrosion Resistant Quiet operation Hydraulically efficient Flexible mounting and body discharge positions No shaft seals NSF certified models available Low current draw and heat rise Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. GRI Overview 0518 050818 Page 8
15651 Series GRI designs and manufactures pumps and pumping solutions for the Original Equipment Market (OEM). All models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. Model Number Voltage (Type) Amps Body Material O-Ring Material Connections Inlet/Outlet (inches) Curve (50Hz/60Hz) 15651-050 115 VAC.45 Noryl EPT/EPDM 1/2 MHB B / A 15651-051 115 VAC.45 Noryl Viton /FKM 1/2 MHB B / A 15651-052 230 VAC.22 Noryl EPT/EPDM 1/2 MHB B / A 15651-053 230 VAC.22 Noryl Viton /FKM 1/2 MHB B / A 15651-054 115 VAC.45 Vectra EPT/EPDM 1/2 MHB B / A 15651-055 115 VAC.45 Vectra Viton /FKM 1/2 MHB B / A 15651-056 230 VAC.22 Vectra EPT/EPDM 1/2 MHB B / A 15651-057 230 VAC.22 Vectra Viton /FKM 1/2 MHB B / A 15651-058 12 VDC.63 Noryl EPT/EPDM 1/2 MHB C 15651-059 12 VDC.63 Noryl Viton /FKM 1/2 MHB C 15651-076 12 VDC.63 Vectra EPT/EPDM 1/2 MHB C 15651-077 12 VDC.63 Vectra Viton /FKM 1/2 MHB C 15651-072 12V BLDC 1.24 Vectra EPT/EPDM 1/2 MHB D 15651-073 12V BLDC 1.24 Vectra Viton /FKM 1/2 MHB D 15651-075 24V BLDC.71 Vectra Viton /FKM 1/2 MHB D 15652-058 12 VDC.63 Noryl EPT/EPDM 3/8 MPT C 15652-072 12V BLDC 1.24 Vectra EPT/EPDM 3/8 MPT D 15652-073 12V BLDC 1.24 Vectra Viton /FKM 3/8 MPT D 15652-075 24V BLDC.71 Vectra Viton /FKM 3/8 MPT D BLDC = Brushless DC. Performance at 50 Hz will be approximately 83% of the performance at 60 Hz. FKM = Fluoroelastomer, FPT = Female Pipe Thread, MPT = Male Pipe Thread, MHB = Male Hose Barb. GRI Overview 0518 050818 Page 9
15651 Series Typical Dimensions 15651 Series AC Models: 1.56 (39.62) 2.38 (60.45) ±.38 4.00 (101.6).22 2.58 (65.53) (5.59) 1.05 (26.67).52 (13.2) DIA.-TYP..562 (14.27) DIA.-TYP..52 (13.21) 15651-050 15651-051 15651-052 15651-053 15651-054 15651-055 15651-056 15651-057 3.00 (76.2) 1.50 (38.1).06 (1.52).172 (4.37) DIA.-TYP. 2-PLC'S..147 (3.73) DIA.-TYP. 2-PLC'S. 1.50 (38.1) 3.06 (77.72).172 (4.37) DIA.-TYP. 2-PLC'S. 3.80 (96.52) 1.25 (31.75) 2.50 (63.5) 3.00 (76.2).375 (9.53) DIA.-TYP. 2-PLC'S. 1.25 (31.75) 2.27 (57.66) 2.52 (64.01) 3.08 (78.23) 4.56 (115.82) 15651 Series DC Models: 15651-058 15651-059 1.58 DIA. (40.13) 2.58 (66.53).562 DIA. TYP. (14.27).52 DIA. TYP. 1.05 (13.21) (26.67) 3.06 (77.72).52 (13.21).060 (1.52) 1.50 (38.1) 3.00 (76.2) 1.50 (38.1).172 (4.37) DIA.-TYP. 2-PLC'S..147 (3.73) DIA.-TYP. 2-PLC'S. 1.50 (38.1).750 (19.05).172 (4.37) DIA.-TYP. 2-PLC'S. 1.25 (31.75) 2.50 (63.5) 3.00 (76.2) Dimensions in Inches (Dimensions in Millimeters).375 (9.53) TYP. 2-PLC'S. 1.25 2.27 (57.66) (31.75) 2.52 (64.01) 3.08 (78.23) 4.56 (115.82) GRI Overview 0518 050818 Page 10
17650 Series Specifications Max Flow 10.5 gpm Max Head 57 ft Max System Pressure 75 psi Max Fluid Temp. 160 F (71 C) Materials in contact with solution / OEM options Body and Housing Vectra * Noryl NSF certified models available 3/8 MNPT Impeller Vectra Bearings Vectra Pump Shaft Ceramic Thrust Bearings Glass-Filled Teflon Reinforced Thermoplastic Resin Vectra O-Rings (Elastomers) EPT/EPDM Motor specifications / OEM Viton /Fluoroelastomer options Nitrile Motor Specs 115V, 50/60 Hz Neoprene 230V, 50/60 Hz Silicone Drip-Proof Kel-F Shaded Pole 12Vdc Brushed-Type & brushless Features 24Vdc Brushed-Type & brushless Corrosion Resistant Quiet operation Hydraulically efficient Flexible mounting and body discharge positions No shaft seals NSF certified models available Low current draw and heat rise TOTAL HEAD - FEET 51 48 45 42 39 36 33 30 27 24 21 18 15 12 9 6 3 0 LITERS PER MINUTE 0 4 8 12 16 20 D G C A F E B 0 1 2 3 4 5 6 U.S. GALLONS PER MINUTE A - 60 Hz curve. B - 50 Hz curve. C - 12VDC curve. D - 12V BLDC curve. E - 12V & 24V BLDC curve. F - 24V BLDC curve. G - 12VDC curve. 16.0 15.0 14.0 13.0 12.0 11.0 10.0 9.0 8.0 7.0 6.0 4.0 3.0 2.0 1.0 0 TOTAL HEAD - METERS Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. GRI Overview 0518 050818 Page 11
17650 Series GRI designs and manufactures pumps and pumping solutions for the Original Equipment Market (OEM). All models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. Model Number Voltage (Type) Amps Body Material O-Ring Material Connections Inlet/Outlet (inches) Curve (50Hz/60Hz) 17651-050 115 VAC.8 Noryl EPT/EPDM 1/2 MHB B / A 17651-051 115 VAC.8 Noryl Viton /FKM 1/2 MHB B / A 17651-052 230 VAC.4 Noryl EPT/EPDM 1/2 MHB B / A 17651-053 230 VAC.4 Noryl Viton /FKM 1/2 MHB B / A 17651-054 115 VAC.8 Vectra EPT/EPDM 1/2 MHB B / A 17651-055 115 VAC.8 Vectra Viton /FKM 1/2 MHB B / A 17651-056 230 VAC.4 Vectra EPT/EPDM 1/2 MHB B / A 17651-057 230 VAC.4 Vectra Viton /FKM 1/2 MHB B / A 17651-060 12V BLDC 3.1 Noryl EPT/EPDM 1/2 MHB D 17651-061 12V BLDC 3.1 Noryl Viton /FKM 1/2 MHB D 17651-062 24V BLDC 1.5 Noryl EPT/EPDM 1/2 MHB E 17651-063 24V BLDC 1.5 Noryl Viton /FKM 1/2 MHB E 17651-064 12V BLDC 3.1 Vectra EPT/EPDM 1/2 MHB D 17651-065 12V BLDC 3.1 Vectra Viton /FKM 1/2 MHB D 17651-066 24V BLDC 1.5 Vectra EPT/EPDM 1/2 MHB D 17651-067 24V BLDC 1.5 Vectra Viton /FKM 1/2 MHB E 17651-068 12V BLDC 3.5 Noryl EPT/EPDM 1/2 MHB G 17651-069 12V BLDC 3.5 Noryl Viton /FKM 1/2 MHB G 17651-070 12V BLDC 3.5 Vectra EPT/EPDM 1/2 MHB G 17651-071 12V BLDC 3.5 Vectra Viton /FKM 1/2 MHB G 17651-078 (MDII) 12V BLDC 1.5 Vectra EPT/EPDM 1/2 MHB C 17651-079 12V BLDC 1.5 Vectra Viton /FKM 1/2 MHB C 17651-081 24V BLDC.75 Vectra Viton /FKM 1/2 MHB C 17651-085 115 VAC.68/.56 Noryl Viton /FKM 1/2 MHB B / A 17651-091 12V BLDC 1.5 Vectra Viton /FKM 1/2 MHB G 17651-094 12V HS BLDC Noryl EPT/EPDM 1/2 MHB F 17651-096 24V HS BLDC Noryl EPT/EPDM 1/2 MHB F 17651-552 230 VAC.35 Noryl EPT/EPDM 1/2 MHB B / A 17651-557 230 VAC.35 Vectra * Viton /FKM 1/2 MHB B / A 17652-051 115 VAC.8 Noryl Viton /FKM 3/8 MPT B / A 17652-079 12V BLDC 1.5 Vectra Viton /FKM 3/8 MPT G 17652-081 24V BLDC.75 Vectra Viton /FKM 3/8 MPT C 17652-552 230 VAC.35 Noryl EPT/EPDM 3/8 MPT B / A Vectra is chemically resistant to most acids, oxidants and bleaches, and organic solvents. (Do not use with chemicals which are bases.) BLDC = Brushless DC. HS = High Speed. FKM = Fluoroelastomer, FPT = Female Pipe Thread, MPT = Male Pipe Thread, MHB = Male Hose Barb. Performance at 50 Hz will be approximately 83% of the performance at 60 Hz. GRI Overview 0518 050818 Page 12
17650 Series Typical Dimensions 17650 Series AC Models: 17651-050 17651-051 17651-052 17651-053 17651-054 17651-055 17651-056 17651-057.25 (6.35) TYP. 5.97 (151.64) "O.A." DUAL FREQ. (FAN COOLED) 2.266 (57.55).969 (24.61) 3.32 DIA. (84.33).562 (14.27) DIA. TYP..531 (13.49) DIA. TYP..750 (19.05).39 I.D. (9.91) TYP..234 (5.94).265 (6.73) 2.375 (60.32) 2.84 (72.14) 2.42 (61.47) GR/YEL WHITE BLACK.50 (12.70) (304.80) 12.00 (STD. LEAD LENGTH) 2.375 (60.32) 2.875 (73.02) 3.50 (88.90) 17650 Series DC Models: 17651-058 17651-059 4.974 (126.34) 2.454 (62.33).750 (19.05).562 (14.27) DIA. TYP..531 (13.49) DIA. TYP..39 I.D. (9.91) TYP..66 (16.76) TYP. 1.750 (44.45) 3.250 (82.55) 1.50 (38.61).750 (19.05).060 (1.52) TYP. 1.532 (38.91).215 (5.46) TYP. 2-PLC'S 2.360 (59.94) 2.822 (71.68) 1.180 (29.97) 1.411 (35.84) Dimensions in Inches (Dimensions in Millimeters) 1.781 (45.24) 1.950 (49.53) 1.246 (31.65) GRI Overview 0518 050818 Page 13
INTG3 Series Specifications Max. Fluid Temp: 203 F (95 C) Max Sys. Pressure: 75 psi Weight: 12.8 oz (362.9 grams) Ports: 1/2, 3/4 MHB, 3/8 MPT Flow Rates: H2O Max Flow: 7.79 GPM, 29.47 LPM Max Head: 54.38 FT, 23.58 PSI Flow and pressure dependent on input voltage Materials in contact with solution Body: PPS (Ryton ) Impeller: PPS (Ryton ) Pump Shaft: Ceramic Bearing: Ceramic Bearing Plate: PPS (Ryton ) Housing: PPS (Ryton ) Rotor Shell: PPS (Ryton ) Static O-Ring: EPDM, FKM (Viton) Motor specifications Motor: Integrated, Brushless DC Supply Voltage: 9-24 VDC It is recommended that the customer provide circuit over current protection to the pump. Electronics Max Power: 60 watt. 5 amp fast acting fuse is recommended. Optional - Consult Factory Remote Speed Control: Third Wire: 0-5 volts (Reference DC NEG). Speed is controlled by a nominal 0-5 volt DC signal. Tachometer feedback option available. TOTAL HEAD - Feet of Water (PSI) 60.00 (26.01) 50.00 (21.67) 40.00 (17.34) 30.00 (13.00) 20.00 (8.67) 10.00 (4.33) 0 0 2.00 (7.57) 9-24VDC 60 Watt Max For voltages above 24, Consult GRI 4.00 (15.14) CAPACITY - GPM (LPM) 6.00 (22.71) 8.00 (30.28) 10.00 (37.85) Note: Testing performed in a controlled laboratory environment. Actual performance may vary (+) or (-) 10% from the information shown. Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. The above curve is an all inclusive overview of the INTG3 Series catalog models represented on this tech sheet. Gorman-Rupp Industries designs and manufactures pumps and pumping solutions for the Original Equipment Manufacturer (OEM). All models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. Agency Approvals UL778: Motor-operated Water Pumps NSF 61: Potable Water NSF 372: Lead Content NSF 169: Special Purpose Food Equipment and Devices (Contact GRI) Mounting Base Options 360 Mounting Bracket: PPS material Rubberized shock absorbing: Elastomer material (Neoprene) Compliances RoHS 2 (2011/65/EC) REACH (SVHC) GRI Overview 0518 050818 Page 14
INTG3 Series Standard Hose Barbed Ports Transportation Ports & Rubber Bracket Note: Testing performed in a controlled laboratory environment. Actual performance may vary (+) or (-) 10% from the information shown. Model Voltage / Lead Wires Max Watts Max Amps @ Max Flow Max Flow GPM (LPM) Max Head Feet (PSI) Connections Inlet/Outlet (Inches) O-Ring Material INTG3-550, 551 9-24 VDC / 2-wire 60 2.15 7.79 (29.47) 30.22 (13.10) 3/4 MHB EPDM, FKM INTG3-552, 553 24 VDC / 3-wire 60 1.99 7.89 (29.88) 29.11 (12.62) 3/4 MHB EPDM, FKM INTG3-560, 561 9-24 VDC / 2-wire 60 2.19 6.73 (25.46) 39.42 (17.09) 1/2 MHB EPDM, FKM INTG3-562, 563 24 VDC / 3-wire 60 2.07 6.73 (25.46) 39.83 (17.27) 1/2 MHB EPDM, FKM INTG3-564, 565 9-24 VDC / 2-wire 60 2.19 6.73 (25.46) 39.42 (17.09) 3/8 MPT EPDM, FKM INTG3-566, 567 24 VDC / 3-wire 60 2.07 6.73 (25.46) 39.83 (17.27) 3/8 MPT EPDM, FKM INTG3-570, 571 9-24 VDC / 2-wire 60 2.88 6.41 (24.27) 53.54 (23.21) 1/2 MHB EPDM, FKM INTG3-572, 573 24 VDC / 3-wire 60 3.18 7.49 (28.34) 54.38 (23.58) 1/2 MHB EPDM, FKM INTG3-574, 575 9-24 VDC / 2-wire 60 2.88 6.41 (24.27) 53.54 (23.21) 3/8 MPT EPDM, FKM INTG3-576, 577 24 VDC / 3-wire 60 3.18 7.49 (28.34) 54.38 (23.58) 3/8 MPT EPDM, FKM 3-Wire: Three wires are required when the pump speed is controlled by a nominal 0-5v DC signal. This is done through a control panel such as a computer or other control devices that is connected to the pump via the third wire. The 0-5v signal controls the speed of the pump, not the voltage supplied to the pump. 2-wire: Two wires provide voltage to the pump. Speed of the pump can be changed by increasing or decreasing the voltage supplied. Connectors: MHB = Male Hose Barb; MPT = Male Pipe Thread O-Ring Material: EPDM = Ethylene Propylene Diene Monomer, FKM = Fluoroelastomer. Testing performed in a controlled laboratory environment. Actual performance may vary (+) or (-) 10% from the information shown. Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. GRI Overview 0518 050818 Page 15
INTG7 Series Specifications Max. Fluid Temp: 203 F (95 C) Max Sys. Pressure: 75 psi Weight: 3.52 lbs (1596.645 grams) Ports: 1 MHB Flow Rates: H2O, 12-30 VDC, 0-5v controller Max Flow: Approx. 19-20 GPM, 72-75 LPM Max Head: 66.22 Feet, 28.71 PSI Flow and pressure dependent on input voltage Materials in contact with solution Body: PPS (Ryton ) Impeller: PPS (Ryton ) Pump Shaft: Ceramic Bearing Plate: PPS (Ryton ) Housing: PPS (Ryton ) Rotor Shell: PPS (Ryton ) Static O-Ring: EPDM, FKM (Viton) TOTAL HEAD - Feet of Water (PSI) 80.00 (34.68) 70.00 (30.34) 60.00 (26.01) 50.00 (21.67) 40.00 (17.34) 30.00 (13.00) 20.00 (8.67) For voltages above 24, Consult GRI 12-24VDC 300 Watt Max Motor specifications Motor: Integrated, Brushless DC Supply Voltage: 12-30 VDC It is recommended that the customer provide circuit over current protection to the pump. Electronics Max Power: 300 watt. 10 amp fast acting fuse is recommended. Optional - Consult Factory Remote Speed Control: Third Wire: 0-5 volts (Reference DC NEG). Speed is controlled by a nominal 0-5 volt DC signal. Tachometer feedback option available. Consult factory for wiring diagram and more specific instructions. Mounting Base 360 Mounting Bracket: PPS material 10.00 (4.33) 0.00 0.00 2.00 (7.57) 4.00 (15.14) 6.00 (22.71) 8.00 (30.28) 10.00 (37.85) 12.00 (45.42) CAPACITY - Gallons Per Minute (Liters) 14.00 (52.99) 16.00 (60.56) 18.00 (68.13) 20.00 (75.70) Note: Testing performed in a controlled laboratory environment. Actual performance may vary (+) or (-) 10% from the information shown. Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. The above curve is an all inclusive overview of the INTG7 Series catalog models represented on this tech sheet. Gorman-Rupp Industries designs and manufactures pumps and pumping solutions for the Original Equipment Manufacturer (OEM). All models shown can be configured to meet specific OEM application requirements. Contact GRI for design points that fall outside of shown parameters. Compliances RoHS 2 (2011/65/EC) REACH (SVHC) GRI Overview 0518 050818 Page 16
INTG7 Series Note: Testing performed in a controlled laboratory environment. Actual performance may vary (+) or (-) 10% from the information shown. Model Voltage / Lead Wires Max Amps @ Max Flow Max Power Rating Watts Max Flow GPM (LPM) Max Head Feet (PSI) Connections Inlet/Outlet (Inches) O-Ring Material INTG7-060, 061 12-30 VDC / 2-wire 7.92 300 16.02 (60.64) 93.93 (40.72) 1 MHB EPDM, FKM INTG7-062, 063 24 VDC / 3-wire 8.20 300 18.87 (71.42) 66.22 (28.71) 1 MHB EPDM, FKM 3-Wire: Three wires are required when the pump speed is controlled by a nominal 0-5v DC signal. This is done through a control panel such as a computer or other control devices that is connected to the pump via the third wire. The 0-5v signal controls the speed of the pump, not the voltage supplied to the pump. 2-wire: Two wires provide voltage to the pump. Speed of the pump can be changed by increasing or decreasing the voltage supplied. Connectors: MHB = Male Hose Barb O-Ring Material: EPDM = Ethylene Propylene Diene Monomer, FKM = Fluoroelastomer. Testing performed in a controlled laboratory environment. Actual performance may vary (+) or (-) 10% from the information shown. Do Not Run Pumps Dry. Pumps must be in a continuous flooded suction environment. GRI Overview 0518 050818 Page 17
Replacement Kits Impellar & Bearing Kits Body Kits Motor Adapter Kits Impeller and bearing kits include front and rear thrust beaings, pump shaft, impeller bearing, adapter disc, impeller and magnet assembly and O-ring. Body kit includes O-ring, body and V-band clamp assembly. Motor adapter kits include motor adapter, screws and washers. Motor/Hub & Magnet Kit Motor/hub and magnet kit includes motor, drive hub, magnet and set screw. Please see Replacement Kit Chart on following page. GRI Overview 0518 050818 Page 18
Replacement Kits MAGNETIC DRIVE PUMP REPLACEMENT KITS Model Impeller & Motor/Hub Body Kit Motor Number Bearing Kit & Magnet Kit Adapter Kit 15651-050 02501-569 02501-572 15651-051 02501-569 02501-573 15651-052 02501-570 02501-572 15651-053 02501-570 02501-573 15651-054 02501-569 02501-574 15651-055 02501-569 02501-575 15651-056 02501-570 02501-574 15651-057 02501-570 02501-575 15651-058 02501-571 02501-572 15651-059 02501-571 02501-573 17651-050 02501-580 02501-576 17651-051 02501-580 02501-577 17651-052 02501-581 02501-576 17651-053 02501-581 02501-577 17651-054 02501-580 02501-578 17651-055 02501-580 02501-579 17651-056 02501-581 02501-578 17651-057 02501-581 02501-579 17651-058 02501-584 02501-582 17651-059 02501-584 02501-583 14110-050 02501-551 02500-573 02501-553 02501-072 14110-051 02501-552 02500-573 02501-554 02501-072 14110-052 02501-551 02500-574 02501-553 02501-072 14110-053 02501-552 02500-574 02501-554 02501-072 14518-050 02501-555 02500-567 02501-557 02501-074 14518-051 02501-556 02500-567 02501-558 02501-074 14518-052 02501-555 02500-568 02501-557 02501-074 14518-053 02501-556 02500-568 02501-558 02501-074 14520-050 02501-559 02500-561 02501-561 02501-074 14520-051 02501-560 02500-561 02501-562 02501-074 14520-052 02501-559 02500-562 02501-561 02501-074 14520-053 02501-560 02500-562 02501-562 02501-074 15700-050 02501-567 02501-565 02501-242 15700-051 02501-568 02501-566 02501-242 GRI Overview 0518 050818 Page 19