INSTALLATION GUIDE & SPARE PARTS CATALOGUE CABIN APPROVED MISTRAL Landini = mistral 40- mistral 45-mistral 50-mistral 55 Mc Cormick= GM40- GM45 GM50 GM55 New Holland= T3010- T3020- T3030- T3040 Val Padana = 1540-1545-1550-1555 1540techno -1545techno- 1550techno -1555techno
AGRITAL S.r.l. Via Leonardo Da Vinci, 20 24040 Arzago d Adda (BERGAMO) - ITALY TEL : +39-0363-87633 FAX : +39-0363-87355 E-Mail: agrital@agrital.com WEB site: http://www.agrital.com Dear costumer, WARRANTY REGISTRATION The warranty is valid only if you fill the form and sent it back to Agrital within 15 days from the date of purchase. The form may be sent by e-mail or by fax. Model of cab or tractor: Cab serial number: Date of purchase: Dealer s name: The warranty is valid for 12 months for defective parts, Agrital doesn t recognize the warranty for breakage caused by improper use, normal wear or damage from the user. For air conditioning system, please fill also the manufacturer s warranty The customer confirm to have received the owner s manual and the maintenance manual. He has been properly informed by the dealer on the correct use of the cabin. For the use of any personal protective equipment the user must follow the directions of his person in charge for the safety at work. The dealer confirms that he has installed the cab in according to instruction provided by the manufacturer, in order that the SAE-OECD approval is valid. Stamp dealer: Date and place: Name, Surname or Company s name: (block letters) Signature:
MAINTENANCE GUIDE Versione 15 LUGLIO2011 Dear Customer, We thank you for choosing an Agrital cab! Here s a reference guide for the most common maintenance operation you ll be performing to maintain your new cab efficient and in good state. CLEANING To clean the interior, we suggest to remove the carpets and clean the separately, in order not to leave them wet. The fixed linings can be cleaned with simple water. DOOR ADJUSTMENT After having installed your new cab, you may need to adjust the door locking by adjusting the attachment of the door latch. This operation must be carried on each time the cab is mounted. To maintain a good efficiency of the locks, we strongly suggest not to operate the tractor with the doors opes, since the vibrations could damage the hinges. HEATING/VENTILATION SYSTEM (water-cooled tractors only) In order to switch from the heating to the simple ventilation, the operator has to turn off the hydraulic outlet tap inside the cab. CLEANING AND CHANGING THE AIR FILTERS We suggest to clean the intake air filter every 150 working hours with compressed air or a vacuum cleaner. After 1000 working hours, we suggest to completely clean the air system by using compressed air. To access the system remove the roof (the silicone will have to be removed as well). We suggest to put new silicone back when mounting the roof again. We suggest to change the air filter once a year. Carbon activated filters have a very limited life span. We suggest to use them only when dealing with special chemical treatments and to use a standard filter for other operations. Store the activated carbon filter in its package when not in use. The life span of the filter depends on the working conditions. The mean life span is about 150 working hour AIR CONDITIONING SYSTEM To keep the air conditioning effective, please remember to clean the radiator on the roof and keep the gas on the compressor at level. To clean the radiator use compressed air. Keep a maximum of 3.5 bar in order not to damage the radiator. To refill the compressor, do not exceed0.7 Kg. for big compressors and 0.5 for small compressors and do not put the system under excessive pressure. For further instructions please refer to the instruction manual of the air conditioning system. Please do not hesitate to contact us for any question! AGRITAL S.r.l.
Here is a brief description for the installation of the product. NB. Refer to the booklet of parts to properly display the pieces. B = Check if there are special considerations for the version of your machine before starting the assembly. A = If the version is not mentioned in paragraph (B) follow these steps: Disassemble completely front and rear roll bars, the arrows, oblò splash guards anterior (right and left) and climb handles that are located on the wings (left and right). Place the bench (7) posterior taking the bottom plates in the same position of the 'roll-coupling of the original bar. Use the original screws to lock it. Position the anterior bracket (22) on the base of the front roll-bar to the taking 'of the machine outside the silent-block pre-assembled. (both right and left) and secure with screws 12x30.
Raise the car using the appropriate hooks and anchor it on the machine doing to support the platforms' s entrance to the platform (* holding the original rubber if present). * 2008 is necessary for the machines, since there is no original on the rubber mat, place mats, rice grain prior to placement of the cabin. Attach the brackets joining the cab of a cantilever beam posterior to the silent-blocks, mounted above, the bench by screws 12x70. REAR BRACKET Attach the brackets to the ANTERIOR cabin with cantilever brackets, welded before, on the front with screws 12x70. At the center of vibration dampers mounted above.
Push the car to obtain the maximum closure of the seal around the rear fender. Also make sure that this will continue to guarantee the right side parallel to the left side of the cab on the platform. Drill holes in the platform to work 'height of the existing holes on the platforms' s entrance and use the screws 12x40 (No. 2 for the no-drill anywhere else). Obtained the optimum location of the cabin tighten the screws of the front brackets hours, and the rear of the platform. In this way, the cabin is completely anchored to the car. Check the correct opening and closing of doors and, if necessary, adjust the lock through the slot. Screw in from 'outside the closures less (21) to the front of the welded plate (where drilling is thought to have a better grip) and at both left and right arrows on the appropriate mount bracket welded previously. Place the inner rear end (38) placing it in the structure of the machine and fixing it to the transom of the cabin with self-tapping screws supplied. Place mats over the platforms' s input. Place the plate on the left side of the mast to fix it (make sure it does not interfere with the opening of the glass). In this operation, you must be careful not to be because, once you are done editing, crushed in any way, the wire d 'lighting.
VIEW IMAGE: Roll- bar BASE: Position for front indicators:
Back closure: License plate: REAR WORKING LIGHT AND ATTACK:
CLOSURES FOR LEVERS. USING THE BRUSHES COATING OPTIONAL: If you are the interior trim to proceed in this order: place finishes starting platform (low) and leaving the top free excess. The top is held tightly and crushed the cab once declined. To deliver the attachment or at the discretion of the POP you can paste them. At the end of the wire connecting the 'power to the starter of the cab of the tractor.
For cabins with heating (optional) remember that: Need to connect the hose to the pump discharge water from the cab of the tractor (the tube that comes in a hundred forward). SEE PHOTO Need to connect the return pipe to the cap which is located near the 'mouth of the pipe (the pipe coming out the far right bottom) SEE PHOTO At the end of it all turn on the engine and let it warm up (at least 5 min.). Once the temperature shut down and wait at least 10 min. to cool. You then have to top up the water in the radiator. B = MACHINE FOR VERSIONS PRIOR TO 2010 DO THESE TIPS:
For cabin-mounted machine NEW HOLLAND: - Under the platforms' s entrance to the cab insert plate thickness. Should be included by matching the shape of the platforms in the amount of sp 3 pieces per side. 10mm. Screws are supplied dates TE M 12X70 No. 4 (TE instead of screws M 12x40) - The 'anchor front of the cabin is through the hole on the bracket welded to the front (and not through the' loop present). The washer should be used so trimmed. - For perfect closure of the lid to insert the gasket adhesive. For cabin-mounted machine LANDINI or / and Mc. Cormick: - The front anchor brackets are different. That be inserted based on the roll bar is fitted to SX thick welded to 'internal one that is inserted DX has no thickness welded. Best regards, Agrital.
FRONTALE E FIANCATE: IL DIEGNO è INDICATIVO
ELENCO COMPONENTI FRONTALE e FIANCATE: N QT DESCRIZIONE CODICE 1 1 Cristallo frontale Apribile 338201100 2 2 Cristallo per Porta 33820300 3 1 Maniglione per porta DX 3381056500 3 1 Maniglione per porta SX 3381057500 4 2 Riscontro e protezione riscontro per serratura 295190060 7401056500 5 2 Serratura DX e SX 290290614 290290624 6 2 Supporto serratura DX e SX 3381002500 3381003500 7 4 Guarnizione per supporto serratura 338106500 8 2 Piastra per aggancio Maniglia 3381004500 9 2 Maniglia pulsante Completa- 290290544 10 4 Cerniera inf.e sup. per porta 3381022500 11 8 Guarnizione per cerniera inf.e sup. 338106300 12 1 Motorino tergicristallo 292190534 13 1 Asta per tergicristallo (piccola) 292190540 14 1 Spazzola tergicristallo (piccola) 292190590 15 2 Faro lavoro anteriore ( optional posteriori) 282190205 16 1 Maniglione per cristallo anteriore -Completo- 1431158500 17 1 Presa lampeggiante 292190210 18 2 Ammortizzatore per porta (dx e sx) 296190190 19 1 Ammortizzatore per cristallo anteriore 296190110 20 1 Porta filtro (c/risc. O a/c) 1791056510 20 1 Filtro aria (c/risc O a/c) 295190040 21 2 Chiusura oblò e porta frecce ( dx e sx) 3381018500 3381019500 22 2 Staffa ancoraggio cabina (dx e sx) 3381013500 3381014500 23 2 Chiusura base roll-bar interno 3381016500 3381017500
POSTERIORE E COMPLEMENTI : IL DIEGNO è INDICATIVO
SCHEMA COMPONENTI POSTERIORE COMPLEMENTI: N QT DESCRIZIONE CODICE 24 1 Cristallo Posteriore Apribile 3382040000 25 2 Cerniera Nylon per apertura front. -Completo- 299190094 26 2 Ammortizzatore per crist. Post. 296190180 27 1 Maniglia per crist. -Completo- 1431158500 28 1 Tampone gommato *** 29 1 Chiusura mobile per tampone gommato 3381041500 30 1 Panca di ancoraggio roll-bar 3381060500 31 1 Staffa porta lampeggiante 1941080510 32 1 Tetto ABS 6061050600 33 4 Chiusura superiore con aggancio tetto 3381051500 34 1 Gruppo riscaldamento ( se richiesto) 1466040400 35 1 Asta per tergicristallo (optional) 292190540 36 1 Spazzola tergicristallo (optional) 292190070 37 1 Motorino tergicristallo (optional) 292190534 38 1 Chiusura interna post. 3381018500 39 1 Porta targa 33810523 21 2 Chiusura esterna oblò e porta freccia -dx/sx- 3381016500 3381017500 PER LE VERSIONI NEW HOLLAND FINO AL 2008: CHIUSURA GIROCOFANO INTERNA cod. AG3380301500 + CHIUSURA GIROCOFANO ESTERNA cod. AG3380302500 + DIMA X SCARICO (PER PERSONALIZZARE SECONDO LE SERIE) cod. AG338033500. + N 6 SPESSORI SOTTOPEDANA cod. AG3381230500. PER LE ALTRE VERSIONI: CHIUSURA GIROCOFANO INTERNA cod. AG3380301500.
ELECTRICAL CONNECTION FOR CONNECT THE LIGHTS, AND OTHER ACCESSORIES ARROWS FOR STOPPING WITH THE CAR YOU CAN CONNECT AS FOLLOWS: We remain at your disposal for any clarification
AGRITAL s.r.l. Via L. Da Vinci, 20 24050 Arzago d Adda (BG) -ITALY- Tel. +039. 0363.87633 fax. +39.0363. 87355 www.agrital.com e-mail = agrital@agrital.com