The globe valves are used as a closing valve for: - noncorrosive fluids - saturated steam - oil - air - petroleum and petroleum products The Characteristics of working conditions: pressure dependency on temperature according to ASME B 16.34. technical description: construction: The construction of cast steel globe valves of MSA is in accordance with the standard API 600, BS 18 73. A spindle has got an outer thread and is either rising rotative or rising non-rorative. The standard thread of spindle is ANSI B 1., type ACME. The spindle and gland packing space meet the requirements of API 600. A spindle is placed in the head of yoke cover firmly or on ball bearings. A cover joint is executed with the help of cover s and s. The globe valves has got cast (forged variably) plow that moves in the vertical direction to a sealing seat. The seats are ed or inserted and secured with a sealing weld around the flow circumference. The minimal thickness of overlay on the sealing surfaces of seat and plow is 1,6 mm, hardness depends on the type of overlay material. The operation is with a classical or impact handwheel or in combination with an angle gear box. The sealing of spindle si executed standardly with the plaited and pressed graphited rings. The properties of globe valve packings of MSA meet the requirements of the regulation Clean Air Act, Amendment from 1990. designed dimensions: Designed dimensions of standard design are stated in the table below. material design: The globe valves are supplied in the different material variants. assembly: The globe valves can be assembled into the pipeline in a random position, but the installation into the position with a vertical spindle axis is recommended. testing: The globe valves are subjected to pressure tests acccording to API 98 on strenght and tightness, tightness of backseat, closure tightness with low pressure ( if it is required in the order), closure tightness with high pressure. order specification: Data necessary for an order: type number, nominal diameter, pressure class, design (connection), type of operation, material of inner equipment, requested tests, accompanying documentation.
basic standard for construction basic construction designed dimension flange dimension dimensions of welded ends testing dependence of maximal allowable pressure on temperature BS 18 73, API 600 ASME B 16.10 ASME B 16. ASME B 16.2 API 98 ASME B 16.34
designed dimensions NPS 2" 2." 3" 4" 6" 8" 10" " 14" Class 10 designed dimensions ["] weight D D1 D2 D3 a f n d L = L1 H Z Dk d1 [kg] 2.00 6.00 4.7 3.62 0.62 0.06 4 0.7 8.00 13.9 1.38 7.78 3/4" 24 2.0 7.00.0 4. 0.69 0.06 4 0.7 8.0 19.29 1.77 9.84 1" 32 3.00 7.0 6.00.00 0.7 0.06 4 0.7 9.0 1.7 1.77 9.84 1" 46 4.00 9.00 7.0 6.19 0.94 0.06 8 0.7 11.0 18.31 1.97 1.7 1 1/8" 68 6.00 11.00 9.0 8.0 1.00 0.06 8 0.88 16.00 20.10 1.97 17.72 1 1/4" 117 8.00 13.0 11.7 10.62 1. 0.06 8 0.88 19.0 21.96 2.28 17.72 1 3/8" 178 10.00 16.00 14.2.7 1.19 0.06 1.00 24.0 29.49 2.60 19.68 1 /8" 30.00 19.00 17.00 1.00 1.2 0.06 1.00 27.0 32.48 3.27 19.68 1 /8" 37 13.2 21.00 18.7 16.2 1.38 0.06 1. 31.00 41.97 3.4 31.0 2" 700 Dimensions of welded globe valves are specified up to nominal diameter ". NPS 2" 2." 3" 4" 6" 8" 10" " NPS 2" 2." 3" 4" 6" 8" Class 300 designed dimensions ["] weight D D1 D2 D3 a f n d L = L1 H Z Dk d1 [kg] 2.00 6.0.00 3.62 0.88 0.06 8 0.7 10.0 1.06 1.7 7.78 3/4" 29 2.0 7.0.88 4. 1.00 0.06 8 0.88 11.0 17.2 1.7 9.84 1" 39 3.00 8.2 6.62.00 1. 0.06 8 0.88.0 17.92 1.97 9.84 1" 4.00 10.00 7.88 6.19 1.2 0.06 8 0.88 14.00 20.48 1.97 1.7 1 1/8" 93 6.00.0 10.62 8.0 1.44 0.06 0.88 17.0 22.84 2.36 17.72 1 3/8" 170 8.00 1.00 13.00 10.62 1.62 0.06 1.00 22.00 31.10 2.28 19.68 1 /8" 300 10.00 17.0 1.2.7 1.88 0.06 16 1. 24.0 32.63 2.7 19.68 1 3/4" 480.00 20.0 17.7 1.00 2.00 0.06 16 1.2 28.0 3.3 3.23 27.9 2" 680 Dimensions of welded globe valves are specified up to nominal diameter 8". Class 600 designed dimensions ["] weight D D1 D2 D3 a f n d L = L1 H Z Dk d1 [kg] 2.00 6.0.00 3.62 1.00 0.2 8 0.7 11.0 16.4 1.7 9.84 1" 4 2.0 7.0.88 4. 1. 0.2 8 0.88 13.00 20.27 1.97 17.72 1 1/8" 6 3.00 8.2 6.62.00 1.2 0.2 8 0.88 14.00 20.47 1.7 1.7 1 1/8" 80 4.00 10.7 8.0 6.19 1.0 0.2 8 1.00 17.00 23.23 2.36 17.72 1 3/8" 13 6.00 14.00 11.0 8.0 1.88 0.2 1. 22.0 34.6 2.76 27.9 1 3/4" 320 7.88 16.0 13.7 10.62 2.19 0.2 16 1.38 26.00 39.7 3.1 31.0 2" 6 Dimensions of welded globe valves are specified up to nominal diameter 6".
standard material specification 1 body 2 cover 3 plow - variants 4 7 8 9 10 11 13 14 1 16 17 18 19 20 21 22 seat 6 - variants label handwheel gland flange spindle wheel cover eye pin bearing grease box guideway adjusting screw WCB 1, 2,, 8, 9, 11, 16 A 10 A 106 B M M LCC A 32 LCC A 32 LCC A 30 LF2 A 320 L7M A 194 7M A 32 LCC A 32 LCB LCB A 217 LCB A 217 LCB A 30 LF2 A 320 L7M A 194 7M WC6, 8 A 217 WC6 A 217 WC6 A 182 F9 A 217 WC6 A 182 F AISI 304 ASTM A 47, A 36 A 10, [ČSN 41 123] A 439 D2 (Ni - Resist) ASTM A 47, A 307 Gr B carbon steel carbon steel C A 217 C A 217 C A 182 F9 A 217 C A 182 F A 182 F321 C A 217 C A 217 C A 182 F9 A 217 C trim - material according to API 600 1 sealing surface of plow 2 sealing surface of seat 3 spindle 4 insert of check valve cap 6 packing box 7 latern ring 8 washer 9 pin 1 2 8 overlay 13 Cr overlay 304 Stelit 6 overlay 13 Cr overlay 13 Cr overlay Stelit Stelit 6 Stelit 6 A 276 410 T A 276 410 T A 276 410 T CI.4 CI.4 CI.4 9 overlay overlay A 276 410 T CI.4 sealing - material design Class 1 cover sealing 10, 300 600 2 gland packing 10, 300, 600 type of sealing spiral graphited sealing RTJ rings set of graphited cords and graphited rings (or according to customer s requirements)
1 body 2 cover 3 plow - variants CF8M, 16 CF8C, 16, F321 C C A 182 F321 CF3, 16 A 31 CF3 A 31 CF3 CF8, 16 A 31CF8 A 31CF8 CN7M 13, 14 A 31 CN7M A 31 CN7M Alloy 20 Gr.4A SAF 220 220 M C M M A 31 CF7N A 31 CF7N 4 seat - variants Slitina 20 220 6 7 8 9 10 11 13 14 1 16 17 18 19 20 21 22 label handwheel gland flange spindle wheel cover eye pin bearing grease box guideway adjusting screw AISI 304 ASTM A 47, A 36 stainless steel stainless steel stainless steel stainless steel stainless steel duplex A 439 D2 (Ni - Resist) ASTM A 47 C A 31 CF3 A 31 CF7N stainless steel stainless steel 1 sealing surface of plow 2 sealing surface of seat 3 spindle 4 insert of check valve 11 13 overlay overlay 316 Slitina 20 overlay Stelit 6 Slitina 20 14 Slitina 20 Stelit 6 16 overlay Stelit overlay Stelit cap 6 gland packing box Alloy 20 Alloy 20 7 latern ring 8 washer 9 pin
applied standards: ASME ASTM ASME API MSS NACE British standards: B 16. flange, pipeline and valve B 16.10 designed dimensions B 16.2 welding ends B 16.34 valves - flanged, ed and welded B 1.20.1 screw threads, general purpose B 16.47 larger steel flanged dimensions (substitute for API 60 and MSS SP-44) B 31.1 pipeline for chemical factories and refineries material specification part V,VIII, IX instrucions for vessels under pressure SPEC Q1 specification for quality systems SPEC 6D specification for pipeline valves 600 ed cover of steel gate valve for oil and gas industries Std 98 valve inspections and testing Std 89 fire-resistant sealing and sealing material SPEC L standards for pipelines SP-6 standard ends of contact surfaces for pipeline and valve flanges SP-2 standard markings for valves, flanges and connecting components SP-44 flanges fo steel pipelines SP-3 method of magnetic testing SP-4 method of radiographic testing SP- visual inspection of steel castings SP-0 graphited sealing for valves with rising spindle (constructional requirements) MR-01-7 ISO 116 - materials for H 2 S - for oil and gas industry MR-01-03 materials resistant to cracking in the corrosive oil surrounding BS 1414 steel gate valve - flanged or welding ends for petrochemistry 1868 steel swing check valves - flanged or welding ends for petrochemistry 1873 steel globe valves and flanged swing check valves for petrochemistry 160 round pipe flange, flanges and valves 2080 designed dimensions 146 valve inspections and testing international standards: EN ISO 9001 ISO 211 EN 10 204 ISO 10 434 / API 600 ISO 14313 / API 6D ISO 208 quality system designed dimensions of actuators to valves type of document for inspection ed cover of steel gate valves for petrochemistry petrochemistry - transfer pipeline system - pipeline valves industrial valves - valve testing with pressure
quality system: The whole manufacturing process is completely monitored and includes the following tests and inspections: acceptance inspections of all input materials and sub-deliveries, inspections of particular components in the course of manufacture, assembly testing, pressure testing, operating testing, non-destructive testing and final inspections of finished product. testing: MSA, a.s. executes the whole range of special tests which verify the properties of valves. They are as follow: pressure testing All pressure tests are executed according to API 98, API 600, API 6D and DIN 3230. MSA, a.s. also performs standardly the special tests according to API 6D. A criterium for acceptance is zero permeability. At the same time, MSA, a.s. executes standardly testing at full operating pressure by which a possible leakage could be detected in the body-cover joint, spindle, fittings or grease box etc. fire testing Fire test is executed at MSA, a.s. according to the standard API 6FD, API 607 and BS 67, part 2, for pressure class 10, 300 and 600. testing on seal strenght Test of seal strenght is executed with methan. cycle testing Cycle test is executed by 3000 cycles (open-close) with water. hydrodynamic and aerodynamic testing MSA, a.s executes this test for the verification of hydropneumatic and aerodynamic properties. operating testing Operating test is executed on all valves at MSA, a.s. non-destructive testing MSA, a.s. executes the non-destructive test in the own facilities and testing room. The non-destructive test includes RT, MT, UT or DP testing. The testing operators are higly qualified and certified according to EN 473 or STN-TC-1A. visual inspection Visual inspection is performed at all castings that are used for the valves of MSA, a.s. according to the quality directive MSS SP- for steel castings and according to order specifications. certification: Quality system of MSA, a.s. is certified according to EN ISO 9001:2000 and API Spec Q1 (Specification D - number 0239). research and development: Specialists of MSA, a.s. work on the development and research of new products and verify their properties as well such as: - suitability of applied material - strenght and rigidity of construction (FEM method) - operability with the emphasis on strenght and controlability - hydraulic and aerodynamic properties etc. New products are tested in the testing room of MSA, a.s. as well as in real operating conditions. The properties of product are observed during the whole service life and findings are applied in the development and production of new products.