*

M210-0043 Rubber Mount Kit M140-1143 Rubber Mount Kit For R&R of the rear rubber hydraulic mount in the Lower For removing or installing the rear Control arm on Mercedes W210 rubber hydraulic mount in the Lower Control Arm on Mercedes W140 M129-2142 Rear Bushing Kit For R&R of the Rear Sub-Frame Differential metallic bushing on W140, W202, W203, W210 M220-0643 Sub-Frame Bushing Kit For R&R of the rear rubber hydraulic mount in the Lower Control Arm on Mercedes W203, 211, 220, 171, 209, 215 M211-0043 Front Suspension Arm Bushing Kit For R&R the suspension bushing on the car w/o removing any parts on Mercedes W211 M2810 Installation Kit For the inner/outer rubber mounts in the Lower Control Arm on Mercedes W 170, 202, 208, 210 M202-0143 Rubber Mount Kit For R&R of the rear rubber hydraulic mount in the Lower Control arm on Mercedes W202, W170 TTS1819 Rear Sub-Frame Kit Rear sub-frame differential mount bushing kit to replace worn out differential mounts from the center of the sub-frame on W124/201 M211-0068 Sub-Frame Ball Joint Kit For R&R the ball joint from/to the steering knuckle on Mercedes W220, W211, W230 M220-0343 Ball Joint Tool Kit For R&R the ball joint, without remove any parts (on car). Applicable: Mercedes-Benz W220, W211, W230 (adapters available separately) ML1140 ML/RV Suspension Bushing R&R Kit For R&R the front rubber mount of rear axle assembly on Mercedes-Benz 163/164 chassis M202-0043 Rear Wheel Carrier Set Use it to remove and isntall support joints in the wheel carrier on Mercedes W124, 129, 140, 201, 202, 210, 220 (This tool incorporates an axial bearing, and a pressure piece which guarangtees the correct position of the new metallic bushings when replaced).

TTS1941 Spring Compressor Strut spring compressor for the MacPherson struts. Designed to fit securely around the spring and protect the spring from damage. ( Front & Rear axle springs) TTS1007 Spring Compressor Jaw Set For TTS1941 Spring Compresssor. Applicable: W203/211 TTS1801 Spring Compressor For Front and Rear Axle springs on W107, W116, W123, W124, W126, W129, W140, W170, W201, W202, W208, W210, W211, W220, W230 (including 4-matic) M203-1553 Sub-frame Bushing Kit For R&R front and rear rubber mounts in the rear axle mount on Mercedes-Benz W203 TTS1376 Universal Valve Spring R & R Kit Replace valve spring and oil seal of valve rod on car, without removing head gasket. Works great in the narrow engine room. Enormous time saving for replacement of valve stem seals. Special design helps compress valve spring regardless of firewall barrier. Applicable: BMW N42, N52, N62, M54, M52, M56, M60, Mercedes M102, 103, 104, M111, 112, 113, 271, 272 M210-0143 Rear Sub-frame Bushing Kit TTS1389 Front Sub-frame Bushing R&R Kit For R&R front and rear rubber mounts in rear axle mount on For R&R the rubber hydraulic mount in the upper and lower Mercedes-Benz W210 control arm, right on the car. Applicable: Mercedes-Benz W203/204/211/212/220/221 M201-1143 Puller Use it to remove or install the rear rubber mounts of the rear axle carrier on Mercedes-Benz W124, W129, W201

BMW 312-240 Ball Joint Puller Big Kit 24 mm, 27mm, 31mm, 36mm Applicable: BMW: E38, E39, E52, E53, E60, E61, E70, E83, E90, E91, E92, R50, R52, R53, RR1, RR2, X5 Mercedes: E-Class (W211), CLS (W219), S-Class (W220), SL-Class (W230) Audi: A4, A6 Carrera lower suspension ball joint Porsche: 996 TTS1727 Ball Joint Puller Scissor type puller allows access to difficult to reach and obstructed ball joints. TST1549 Steering Torque Rod Joint Separator Special design with self-locking nut to remove and install the torque strut at front axle. Bore size: M14x1.5 Applicable: Mercedes W171, W203, W209 TTS1808-24mm Ball Joint Separator For splitting track-rod ends, anti-roll bar, ball joints,... etc., especially in confined space conditions on Mercedes W170, W202, W210, W220 (Also applicable on BMW, VW Audi) TTS1092-24mm Ball Joint Separator For splitting track-rod ends, anti-roll bar mountings, ball joints on Mercedes-Benz W202/ W210/ W220 B90A Front Wheel Bearing and Hub Puller Kit For removing and installing front wheel bearings with the spindle on the car Applicable: Mercedes-Benz, BMW, VW/Audi, Porsche, Volvo, toyota/lexus, Nissan Infinity, Honda/Acura, and other Asian makes, TTS1083-21mm Ball Joint Separator For removal of the track-rodend from the drag link on Mercedes-Benz type 201, 123, 124, 126, 129..etc (Also applicable on BMW,VW Audi) TTS1089 Universal Heavy Duty Hydraulic Hub Remover Hydraulically driven, this kit quickly pushes the axle out of the hub, and remove the hub. Kit including Hydraulic ram, 4 lug and 5 lug adapters TTS1446 * M220-0033 Ball Joint Separator Puller for track control arm and radius rod at stub axle assembly joints (used with 10 tons hydraulic press foot pump). Applicable: Benz W211 / W221 / W215 / W219 / W220 / W230 B90K Wheel Bearing Master Kit For removing and installing front and rear wheel bearings on most of the cars

M210-0107 Pin Wrench B-M1550 Fuel Level Sending Unit 5 mm pin wrench for R & R For removing the plastic fuel tank lever-type fuel lever sensor lid on Mercedes-Benz on Mercedes W140,210 W211, W203, BMW, VW-Audi M204-212 Fuel Tank Lid Remover For removing and installing the plastic fuel tank lid on Mercedes W204, W207, W212 BMW, Volvo cars... M900-0007 Strut Nut Socket For R&R the seal top air suspension strut nut on Mercedes-Benz W220 M103-0040 Fan Holding Tool For holding fan pulley while loosening or tightening screws on viscosity fan coupling on Mercedes-Benz M102, 103, 104 engines TST3265/65mm Fan Clutch Wrench 65 mm open end wrench for replacing the radiator fan hub on Mercedes M103 (6 cylinder), M104 (6 cylinder 4 valve) M119 (8 cylinder 4 valve), M120 (12 cylinder 4 valve) engines TTS36mm Open End Wrench For M111, 112,113, late models 119, 604 Used with fan hub holder # 113-0040 001 589 0007 00 M220-0061 ABS Shock Absorber Service Kit For removing the top seal on the Airmatic air suspension strut on Mercedes-Benz W220 M113-0040 Fan Holder For holding fan pulley while loosening or tightening screws on viscosity fan coupling on M112, 113, 119.985 (1996-2003) M119-0240 Fan Holder For holding fan pulley while loosening or tightening screws on viscosity fan coupling on M111, OM604, 605, 606 M202-0007 Pin Wrench socket Use it to remove fuel sender retainer nut on Mercedes-Benz W202 TTS1399 Fuel Tank Lid Wrench Fuel delivery slotted wrench for lock ring on fuel pump/ sending unit on Mercedes-Benz M classsw163/w164 from 2005-2011 R class W251 M2186 Engine Mount Wrench Set 16mm, 17mm Special angel designed to remove the nuts from Benz engine mount 16mm: Mercedes W220, 210, 203, 221, 211, 204, 17mm: Mercedes W124, 140, 170, 126, 201, 202, 210, M120-0621 * M120-0721 Dipsticks M120-0621: For determining oil level and inspection length of dipstick guide tube on Mercedes 103.943/984/985, 104, 111, 119, 120, 137, 603, 604, 605, 606, 611, 612, 613, 628, M120-0721:For measuring oil level and for checking length of oil pipe on M112, 113, 271, 271, 646, 647, 648 M111-1231 Support with Handle For driving in the tulip shaped, flared oil dipstick guide pipe into crankcase on All Mercedes-Benz M210-0015 Oil Seal Installer (Drift punch) For shaft sealing ring on inside of front axle housing. Model: 210.081/082/282, 211.08/28/09/29 (M111 engines) TTS1000 Puller Wrench Spark plug boot wrench for V6 Mercedes-Benz M3857 3/4" M-Class Drive Socket To secure retaining ring for ball joint replacement on 163 M-Class front and rear axles. Retaining ring is torqued to 300Nm/226 ft/lbs

M201-0037 Timing Chain Guide M276-0140 Cam Timing Kit To hold down the camshaft (4 pcs set) on Engine: 157, 276, 278 M104-0037 Timing Chain Guide M271-0140 Camshaft Timing Kit M271-0015: Install the plug into the timing case cover (access to chain tensioner) M271-0031: For unloading the timing chain tensioning device on Mercedes M271 M271-0140 Timing Chain Retainer for drawing in the timing chain. Retain timing chain with camshaft sprockets in proper timing position. M271-0061 Camshaft Retaining device makes it possible to position the camshafts in the installed position. This makes it possible to slacken and tighten the bolts attaching the camshaft gear. TTS4047 Camshaft Timing Kit For positioning the camshaft in 30 degree TDC position Applicable: M275, M285 (C for the left bank, A and B for theright bank), M137 (A and B) M156-0061 Cam Timing Kit Use on M156 AMG V8 Mercedes engines in the 2007-present 63 series for servicing the camshaft, timing chain and cylinder head. M270-0061 Camshaft Timing Kit This holding device makes possible holding down and fixing of the camshaft. This makes possible to slacken and tighten the bolts attaching the camshaft gear on M133, M270, M274 engines (late A Class, B Class CLA, C Class and E Class Specially designed for vehicles fitted with chain driven 1.6/2.0l direct injection gasoline engine. Supplied with small and large diameter clamp pieces to ensure the camshaft is correctly held in place. Supplied with special security bit socket for the camshaft pulleys. Designed to allow removal and assembly of the camshafts. M112-0132 Camshaft Holders with 38 mm Wrench Holds camshaft in 40 degree TDC position (left/right side). Mercedes-Benz M112, M113 38mm wrench: For turning the cam M111-0315 Retaining Pins For holding camshaft tight in installation position (25 degree after ignition TDC). Applicable: M111, 119, Om604, 605, 606, 611, 612, 613, 628 MBZ1500 Cam Timing Kit The retaining device makes it possible to position the camshafts in the installed position, also for turning, installing/removing the crankshaft pulley. (OEM#: 651589014000, 651589004000, 651589024000. Application: Benz OM 651 Volume 2.0D / 2.2D / 2.5D. Models of car: Benz GLK (W204), Benz CLA 200 CDI, Benz CLA 220 CDI, Benz A Class W176, Benz Sprinter 316CDI OM651.

TST1725B Dashboard Service Kit Required to properly service various Mercedes dashboard components without causing undue damage. 8-piece tool kit contains: (2) removal tools for ignition lock on model W126. (2) removal tools for ignition locks on models W124 & W201. (2) removal hooks for instrument cluster on models W107, W116, W123, W124, W126, W140, and W201 (2) radio removal tools on models W129, W140, W202, and W210. M111-1861 Universal Valve Spring Compressor Arm Universal valve spring compressor arm for the R&R valve springs. Use it together with the following pressing devices. on M102, 103, 104, 111, 119, 120, Om601,603, 604, 605, 606 M102-1160 Pressing Device Applicable: M102, 103, Om601, 602, 603, M102-1063 Pressing Device Applicable: M190E2.3 L 16-V M202-0014 Turning Tool For R&R of protective cover for ignition steering lock (from 1992). W123, 124, 126,129, 140, 163, 170, 202, 210, 414 M210-0007 (M129-140) Turning Tool For loosening and tightening the ring (rosette) of the electronic ignition switch on W129, 140, 202(as of June 97), 208, 210, 211, 230, 240, 463 TTS140-1663 Panel Wedge Special design for removing the door panel on W140 TTS1333 Bushing Installer Special Pliers for installing the nylon shift shaft bushings (transmission gear lever rubber) on most Mercedes models. (Also working on BMW, VW-Audi...) M102-103 Post Set M111-0159 Support Bridge Use it to support the valve spring compressor. Applicable: M104, 111, 119, 120, Om604, 605, 606 M110-0461 Valve Spring Compressor Kit For M110 Engines M271 Crankshaft Front Gear Wheel Socket For removing crankshaft front gear wheel on M271 Special angel designed to remove the nuts from engine mount M900-0059 Ignition Lock Set Use it to release retainers for removal of ignition switch. Applicable: W124, 126, 129, 201 M5843 Chain Link Press Tool Kit Use to press on external lugs and rivets of dip-type fasteners of simplex and duplex roller chain Application: Benz Model 615, 616, 617, M102, M103, 116, 272, 272, BMW and SAAB M140-1521 Transmission Oil Level Dipstick For checking ATF level on 1997 & newer cars 722.6 transm. M168-0121 Transmission Oil Level Dipstick For determining oil level on 716.5, 722.7, 722.8 transmission

M119-0114/651-0161 Front/Rear Crankshaft Radial Seal Installer For replace front and rear crankshaft radial sealing ring on Benz M102, M111, M112, M113, M137, M156, M159, M272, M275, M285, M601, M602, M603, M604, M605, M606, M628, M629. M112-0040 Holder For holding the vibration damper when loosening the bolt on the crankshaft on Mercedes-Benz M112, 113, 137 Replaceable bolts M271-0003 Harmonic Balancer Pulley Holder For removal and replacement of the crankshaft bolt on M271 M271/272/273/642 Crankshaft Hub Locking Kit TTS1347 Rear Crankshaft Radial Sealing Ring Installer Designed to prevent damage when assemble the cover to the crankshaft flange on Benz M271, M272 Guide seal on the cover M112-0961 Parking Brake Installer Pressured spring of parking brake Applicable: All Mercedes models Take off the front part, and push the cover into the flange M271-T50 Alternator Pulley Remover ½"Drive, T50 Star: for assembling and dismantling the free wheel pulley while changing the alternator or pulley on BOSCH alternators on Mercedes, BMW, Audi,VW... M271-10mm Alternator Pulley Remover ½ Drive, 10mm 12 point: M271, VW Golf, Vento, Passat, AudiA3, Volvo, VW Jetta with 1.9 L TDI engines M28 Radiator Adapter - Early type For US type radiator pressure testers to earlymodel radiators with large cap (all Mercedes-Benz before 1968) TST4727 Compressor Belt Pulley Wrench For R and R the compressor belt on Mercedes-Benz M112, M113, M272, M273 M606-0009 Oxygen Sensor Socket TTS1251 16mm Spark Plug Socket 3/8" Drive 16mm, length 93mm, outer dia: 22mm, spark plug socket with retaining spring and joint. Applicable: Mercedes M112, 113, 137, 155, 166, 271, 272, 273, 275, 902, 906, BMW X6, Oil Filter Sockets, for R&R of oil filter cartridge elements TTS2402-27: 3/8" Dr. 27 mm for M163 (ClassA), C230 TTS2402-32: 3/8" Dr. 32 mm for OM 364, 366, Volvo, Audi... TTS2403-36: 3/8" Dr. 36 mm for OM604, 605, 606, M116 BMW M52, M60, M62, M70, M73 engines TTS2402-76: 3/8" Dr. 76 mm 12 point for M102, M103 TTS2402-84: ½" Dr. 84 mm 14 point for E320 (ML), (2007-210 Dodge Sprinter) TTS2402-86: ½"Dr. 86 mm 16 point for Volvo S40, S60, S70, S80...(from 1999-2003), BMW(316i, 318i, 2001-onwards) N40, N42, N45,N46 engines TTS2402-86: ½" 86mm, 18 point for VW Golf (MKIII. Tdi, Passat Tdi), Audi A6 TDi, Citroen, Peugeot, Renault, TTS2402-108: 108mm, 15 point for Volvo

TTS178A Automatic Transmission Fluid Filler Kit Use to fill the 722.9 transmission, along with VW/Audi, BMW, Mercedes,... other cars Tank capacity: 7.5 Liter Flow capacity 75 cc/cycle Contains standard fitting 8pcs Hose size 3/8" x 4.5 ft. Size 260x 370x 595mm Special designed for filling ATF oil. Replaceable fittings for different vehicles. With hand pump for vacuum to prevent oil deterioration. AST722-9 Universal Pneumatic Oil and Liquid Dispenser Provide with the safety valve helps the pre-setting pressure (43psi (3kg/cm2) relief automatically. Provide with pressure gauge makes read and control the air pressure in the tank easier... Used for filling fluids in transmission, differentials and transfer cases (not suitable for use with fuels or solvents). Special adapters for each models available separately or Complete Euro / Asian Kit ATF 101 (applicable to Ford) ATF 102 (applicable to BMW, Honda, Nissan and many other universal applications) ATF 103, ATF 104, ATF 105, ATF 16 DSG and ATF 17 CVT (applicable to VW/Audi) ATF 104 (Applicable to 1999 and newer Porsche Models) ATF 105 (Mini Cooper) ATF 129 (applicable to Mercedes 722.9 Transmissions) ATF-TOY118 (applicable to Toyota) NST1243 Gearbox Filling Tool Adapter For Mercedes W221, 722.9 transm. TTS1017B 17pcs Diesel Injector Seat Cutter Set To clean and re-cutting the injector seat of modern common rail diesel engines. (BMW, Ranult, Ford), 19mm flat reamer for Bosch injector(benz) 19mm angle reamer for FIAT, Iveco TTS1318 Air Suspension Piping Socket Special Open design socket to remove the nut while keeping it away from the air suspension pipe on Mercedes-Benz W211, W221, W164 TTS160-2 Fuel Line Plug Set For Mercedes-Benz with fuel injection system M103-0114 Sleeve 20.0mm to install timing cover with seal in place, preventing damage to the seal. Applicable:M103, 104 March 89 and newer TST2189-9mm, 6 point 1/2" Drive Socket For Mercedes-Benz M and R and GL Class brake caliper Applicable: W163, W164, W251 Dimension: Length 78mm, Hex 9mm TTS2167 Star-E Socket Set For cylinder head bolts on BMW, Mercedes CDI engines Length - 140 mm, Size: E10, E12, E14, E16, E18, E20 8900 Sleeve For installing clutch piston K1 K2 into external disc carrier transmission 722.3, 722.5 TST4054 Broken Glow Plug Remover Set Mercedes-Benz (09-diesel) model: CDI for removing broken glow plugs. Comes with 1/4" 8mm and 10mm taps.(cdi) M733/6 Cylinder Head Rail Guide Pin Puller Use it to remove pins from the cylinder head on all Mercedes-Benz

Singing Power Probe To diagnose more easily than before. The inside of may electrical parts has coil. When the vehicle power is on the magnetic power starts flow the coil, than the coil becomes magnet in a moment. At this very moment, Singing probe detect a line of magnetic force with beeping and blinking. Just touch the coiled part. Beep & Lights on? That means the part itself has no problem at all. If there is no sound or light on Singing probe, that means the part is not working or the power is off. Can test a various kind of parts: Gasoline injector, Lpi Injector, CRDi Injector, Ignition coil, Solenoid Valve, EGR Valve, ISA Valve Relay Alternator, Motors...etc.. (any parts if it is coiled inside.) W221 Lug Nut Socket 17mm special wheel lug socket for W221 engines. 1/2"(17mm) 45mm length: Maybach, W221 (S-class and late CL-class which came installed with unique convex lug bolts TTS1303 Benz A/C Low Side Coupler Remover Special designed, to remove the A/C low side coupler on Benz W221, 211, 204, 219 M601-0240 Flywheel Lock Locks flywheel at starter ring gear from the transmission side on Mercedes-Benz M102, M103, M104, M111, M601, M602, M603, M605, M606, M611, M612, M613 M112-0340 Flywheel Lock Use to lock crankshaft on starter ring gear (mount in starter hole) for vehicles with left and right hand-steering on Mercedes-Benz M112, M113, M137, 155, 156, 272.979, 273, 629, 642.992, M915-0207 Socket 1/2" Drive, for grooved nut on rear axle shaft flange. Needed when replacing axle bearing or axle seal on 107, 114, 115, 116, 123, 126 chassis with constant velocity joint axles.

BMW Rear Axle Carrier Kit For R&R the Rear Axle Carrier Mount Bushings w/o completely lowering the rear axle assembly on BMW E39, E46/E85, E53 Mercedes-Benz Rear Sub-frame Bushing Kit For R&R front and rear rubber mounts in rear axle mount on Mercedes W210 BMW2336-E53: BMWE53/X5 Bush#:33 31 1 770 454 E46/E85: BMW E46, E85 Bush#:33 31 092-515/516/517 Base unit Mercedes W210 E39 Sedan and Wagon