Hydraulic breakers and drills Powerful, lightweight and portable
The best power-to-weight Construction and rental companies around the world are discovering the advantages of using hydraulics. They know that hydraulic equipment offers the best power-to-weight ratio of any system. And they appreciate that a hydraulic power pack is so small and light that two people can lift one up and fit it in the back of a van. A real cost advantage Smaller construction and rental companies have been quick to understand the very real cost advantage of hydraulics. For the price of one compressor/breaker combination, you can buy two complete hydraulic power pack/breaker sets. In fact, you might not need a power pack at all: with the help of an oil flow divider and an extension hose, you can hook hydraulic tools directly to a hydraulic-powered carrier. Hydraulics hit harder The first time you use a hydraulic breaker, you re in for a surprise. Here s this compact, quiet tool and it hits harder than any other type of breaker. That s because hydraulics are more efficient than electric, pneumatic or petrol-driven tools. For example, a 32 kg hydraulic breaker gives you the same hitting power as a 40 kg pneumatic. Thanks to their amazing impact energy, hydraulic breakers can be used on concrete, asphalt and frozen ground. You can, of course, also use them for trenching, tie-tamping, spike driving and general demolition. Easy to own There s not much that can go wrong with an Atlas Copco hydraulic breaker. With just two moving parts, there s minimal wear and very few parts to replace. Hydraulics are by nature reliable: working in a closed loop, dirt and moisture are kept out. And due to the no-spill, flat-face couplings, it s easy to keep the system clean.
A harder hitting hammer LH 11 Powerful horizontal pick hammer This D-handle breaker is ideal for horizontal work in brick, mortar and light concrete. It is one of the most powerful pick hammers on the market, featuring an impact energy of 25 joules and impact rate of 2,400 blows/min. With its detachable front handle, the LH 11 is a popular choice for renovation, demolition and structural alteration jobs. Front handle The front handle, whih is available as an optional extra for the LH 11, helps to increase control and reduce fatigue. It pivots 360 for optimal positioning and is easy to detach. Pick hammer LH 11 Shank size Hex mm 22x82,5 Weight kg 12,6 Length mm 600 Oil flow l/min 20 Working pressure bar 70-90 Return line pressure max bar 10 Vibration level (ISO 8662-5) m/s 2 1) 10,1 Impact rate (20 l/min) blows/min 2400 EHTMA class C Part number 1801 1741 18
A complete line of T-handle breakers LH 18/19 E Lightweight, multi-purpose breakers Used to break brickwork, frozen soil, asphalt, concrete, as well as for tamping and compaction. Delivering 65 joules at 1,600 blows/min (average), the LH 18/19 E are very effective tools. The breakers are popular with contractors and rentals for indoor and outdoor renovation and demolition jobs. And they are the preferred choice for major railroad companies. LH 22/23 E Medium weight, multi-purpose breakers Among the best general purpose medium weight breakers available in the 23-28 kg range the LH22/23 E are used by leading rental companies around the world. These breakers are commonly used with a 5 asphalt chisel for road building and maintenance applications, but also work well in brickwork, frozen soil and concrete. Can be used with both 30 l/min and 20 l/min power packs. LH 27/28 E Heavy-duty, multi-purpose breakers These breakers give you heavy-duty breaking in frozen soil, asphalt and reinforced concrete and are considered to be among the best in their class. Delivering 110 joules at 1,500 blows/min (average) the LH 27 and LH 28 E are powerful and highly effective. They work at a standard flow rate of 30 l/min, and at 20 l/min with a simple adjustment. LH 39/40 E Super heavy-duty breakers Hitting at 150 joules and delivering an average of 1,275 blows/min, the LH 39 and LH 40 E are among the most powerful handheld breakers in the world. They are used for the most demanding jobs in heavy asphalt, reinforced concrete and foundations. Popular with contractors throughout North and South America as well as South Africa, they often replace miniexcavators with mounted breaker attachments. Available shank sizes LH 18 LH 19 E LH 22 LH 23 E LH 27 LH 28 E LH 39 LH 40 E Shank size 25 x 108 1801 3440 81 1801 3440 82 1801 3541 08 1801 3540 83 - - - - Shank size 28 x 152 1801 3445 52 1801 3445 53 1801 3540 84 1801 3540 85 1801 3640 92 1801 3640 93 1801 3741 62 1801 3741 65 Shank size 28 x 160 1801 3445 54 1801 3445 55 1801 3540 86 1801 3540 87 1801 3640 94 1801 3640 95 1801 3741 63 1801 3741 66 Shank size 32 x 152 1801 3445 56 1801 3445 57 1801 3540 88 1801 3540 89 1801 3640 96 1801 3640 97 1801 3741 54 1801 3741 68 Shank size 32 x 160 1801 3445 58 1801 3445 59 1801 3540 90 1801 3540 91 1801 3640 98 1801 3640 99 1801 3741 64 1801 3741 69
Vibration-dampening handle The spring handle provides vibration dampening. In addition to this, the handle offers enhanced durability and easy maintenance. Keep-clean couplings To keep hydraulic systems clean, hoses are fitted with high quality couplings. They comply with HTMA (Hydraulic Tool Manufactures Association) standards and give easy, fast and safe connections even in industrial and mining applications in which there are high concentrations of dust and dirt. High productivity design The slim design gives good line of sight to the chisel point to boost productivity. Operator fatigue is reduced thanks to the well-balanced design and the elimination of external side bolts and machine parts that could come into contact with operator s body. Breakers with advanced vibro-reduction LH 19 E LH 23 E LH 28 E LH 40 E Weight kg 19,1 21,3 25,6 33,1 Length mm 638 682 760 760 Oil flow l/min 20 30 1) 30 1) 30 2) Working pressure bar 90-110 105-125 105-125 105-125 Return line pressure max bar 10 15 15 15 Vibration level (ISO 8662-5) 3) m/s 2 3,5 3,3 3,4 6 Impact rate (20 l/min) blows/min 1600 1450 1270 - Impact rate (30 l/min) blows/min - 2160 1860 1150 Impact rate (40 l/min) blows/min - - - 1500 EHTMA class C D (C) 1) D (C) 1) D (E) 2) Standard breakers LH 18 LH 22 LH 27 LH 39 Weight kg 18,7 20,9 25,2 32,2 Length mm 638 682 760 760 Oil flow l/min 20 30 1) 30 1) 30 2) Working pressure bar 90-110 105-125 105-125 105-125 Return line pressure max bar 10 15 15 15 Vibration level (ISO 8662-5) 3) m/s 2 8,3 11,4 11,4 14,2 Impact rate (20 l/min) blows/min 1600 1450 1270 - Impact rate (30 l/min) blows/min - 2160 1860 1150 Impact rate (40 l/min) blows/min - - - 1500 EHTMA class C D (C) 1) D (C) 1) D (E) 2) 1) Can be adjusted to 20 l/min 2) Can be adjusted to 40 l/min 3) LH 18/19 E, LH 22/23 E and LH 27/28 E measured at 20 l/min, LH 39/40 E measured at 30 l/min
The lightweight drill for heavyweight drilling LHD 23 M rock drill This lightweight tool is designed for drilling blast, anchor and rock-splitting holes. Used for example by contractors, armies and utilities who want convenient and efficient drilling without large compressors. With standard integral steel, it drills diameters of up to 50 mm and depths down to approx. 6 m by using hydraulic power for impact and rotation. A small additional compressor is needed for flushing. Rock drill LHD 23 M Shank size Hex mm 22x108 Weight without hoses and drill kg 24,5 Service weight kg 28,3 Oil flow l/min 20-25 Working pressure bar 100-140 Return line pressure max bar 15 Impact rate blows/min 2400-3000 Revolutions rpm 320-400 Torque Nm 65 Direction of rotation CW 1) EHTMA class C Part number 1801 3800 01 1) CCW available as option 1801 3800 02
Petrol-, diesel- or electric-driven power packs Lightweight, compact and portable These well-proven power packs are the ideal power source for a wide range of applications in the 20-40 lpm/172 bar range. Light and compact, they are easy to store and transport. Equipped with wheels and handle, they are easy to move around construction sites. Reduce fuel consumption and noise All 20-30 lpm petrol power packs are equipped with Power On Demand (POD). This hydraulic regulatory system automatically idles the engine when the tool is not being used and speeds it up when the tool is activated. Efficient cooling The thermostatically-controlled oil cooler allows quick warm-ups and helps protect the hydraulic oil from overheating. Correct working temperature is achieved within minutes even during the winter. Foldable handles One person can move power packs around site with ease. On/off valve Easy tool change and slow start up with the variable flow on/off valve. Filter indicator All power packs feature a large, easyto-read filter gauge that indicates when it is time to change the filter. Power packs LP 9-20 P 3) LP 9-20 E LP 13-20 DEL LP 13-30 P 3) LP 18-30 PE LP 18-40 PE LP 18 Twin E 2) LP 18 Twin PE 2) Engine 9 HP Honda petrol 5.5 kw / 3x400 V / 16A Electric 10 HP Lombardini diesel 13 HP Honda petrol 18 HP B&S Vanguard petrol 18 HP B&S Vanguard petrol 11 kw / 3x400 V / 32A Electric 18 HP B&S Vanguard petrol Weight (incl oil) kg 74 70 116 91 110 110 123 110 Dimensions (LxWxH) mm 585x525x680 585x525x680 705x600x745 705x600x745 720x700x745 720x700x745 705x600x745 720x700x745 Oil flow l/min 20 20 20 20-30 20-30 20-40 2x20/1x40 2x20/1X40 Maximum pressure bar 150 140 140 155 172 155 155 155 Fuel capacity l 6-5,5 6,5 7,2 7,2-7,2 EHTMA class C C C C/D C/D C/D/E C/E C/E Hose included YES NO NO YES NO NO NO NO Power on Demand (POD) YES NO NO YES NO NO NO NO Oil control: engine oil YES NO NO YES NO NO NO NO Electric start NO YES YES NO YES YES YES YES Part number 1807 0080 09 1807 0080 15-1807 0110 12 1807 0160 18 1807 0160 17 1807 0160 22 1807 0160 16 Non-silenced versions Part number 1) 1807 0080 31-1807 0110 20 1807 0110 23-1807 0160 31-1807 0160 32 1) Not sold within EU. 2) Version with twin and single pump configuration and different flow and pressure settings also available. Please contact your Atlas Copco sales representative for further information. 3) Extension hoses come as standard with LP 9-20 P and LP 13-30 P.
A wide range of top quality chisels At Atlas Copco, we maintain a comprehensive range of chisels so that you can select the right tool for the job. Atlas Copco chisels are probably the hardest wearing on the market. A controlled heat treatment process imparts both strength and high wear resistance to deep surface layers whilst maintaining a tough shock resistant central core to resist breakage. The striking face is end-milled. This results in better contact between the piston and the tool, improved transfer Point to flat (ISO) W 22 x 82.5 mm 25 x 108 mm 28 x 160 mm 32 x 160 mm L W (mm) L (mm) Part no. W (mm) L (mm) Part no. W (mm) L (mm) Part no. W (mm) L (mm) Part no. Moil point 380 3083 3242 00 380 3083 3253 00 380 3083 3271 00 380 3083 3205 00 1000 3083 3243 00 450 3083 3272 00 450 3083 3206 00 1000 3083 3273 00 1000 3083 3207 00 Narrow chisel 25 380 3083 3244 00 28 380 3083 3254 00 32 380 3083 3274 00 35 380 3083 3208 00 25 1000 3083 3245 00 32 450 3083 3275 00 35 450 3083 3209 00 32 1000 3083 3276 00 35 1000 3083 3210 00 Wide chisel 75 380 3083 3246 00 75 380 3083 3255 00 75 380 3083 3277 00 75 380 3083 3211 00 Wedge chisel 35 380 3083 3250 00 35 380 3083 3258 00 40 400 3083 3282 00 40 400 3083 3216 00 Digging chisel 75 450 3083 3247 00 75 380 3083 3256 00 75 380 3083 3279 00 75 380 3083 3213 00 Digging spade 120 400 3083 3248 00 120 380 3083 3257 00 125 380 3083 3280 00 125 380 3083 3214 00 Asphalt cutter 125 380 3083 3069 00 115 300 3083 3278 00 115 300 3083 3212 00 Clay spade 125 430 3083 3249 00 125 430 3083 3033 00 140 380 3083 3281 00 140 380 3083 3215 00 Shaft for pad 310 3083 3251 00 280 3083 3259 00 230 3083 3283 01 235 3083 3218 01 Tamping pad, round 175 3083 3252 10 175 3083 3252 10 180 3083 3301 00 180 3083 3301 00 Tamping pad, square 175 3083 3239 00 175 3083 3239 00 150 3083 3302 00 150 3083 3302 00 Tamping pad, square 200 3083 3197 00 200 3083 3197 00 Driver pad, round 100 9245 2817 90 100 9245 2817 90 Tie tamper 100 565 3083 3319 00 100 565 3083 3217 00 Power Pack BIO-OIL Each power pack comes with 2 x 4 l bottles of Atlas Copco biodegradable oil, enough for filling the power pack and 7 m hose. Extension hoses By adding one or two 7 m extension hoses you can use up to 21 m of hose with no significant drop in pressure. The hoses are light and flexible and are fitted with flat-face, quick release couplings. (Extension hoses come as standard with LP 9-20 P and LP 13-30 P). Oil flow divider The oil flow divider allows you to run tools from hydraulic-powered carriers by reducing flow and pressure. An extension hose is required to connect the divider to the tool. Size 4 litres Part number 3371 8077 51 Length m 7 12 Couplings: flat face quick release of energy, as well as less vibration and wear on both hammer and chisel. For drill steel and other accessories, please see the Atlas Copco Working Tools and Accessories Catalogue, or contact your local Atlas Copco representative. dimension 1/2" 1/2" EHTMA class C/D C/D Part number 3371 8010 87 3371 8010 89 Type LFD 20 LFD 30 Max oil flow rate in l/min 60 120 Regulated oil flow rate l/min 20-25 25-38 EHTMA class C D Part number 1801 1632 29 1801 1642 32 Check out other handheld hydraulic tools from Atlas Copco Cut-off saws Core drills Pumps Ground rod drivers Post drivers Post pullers Post hole borer Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability. 3392 5148 01 2007, Atlas Copco Construction Tools AB, Stockholm, Sweden Intellecta 2007 Formalix 2007 Subject to technical modifications. www.atlascopco.com