NOTE: All orders are accepted on the basis of prices in effect at the time of shipment.

STANDARD PRODUTS Price Sheet GR.STD-4.18 Effective: April 2, 2018 ancels Price Sheet GR.STD-5.17 of May 1, 2017 FOR THE MOST URRENT PRODUT/PRIING INFORMATION ON ANVIL PRODUTS, PLEASE VISIT OUR WEBSITE AT WWW.ANVILINTL.OM FREIGHT ALLOWANE: All prices are F.O.B. point of shipment. On shipments weighing 2,500 pounds or more, rail freight or motor freight at the lowest published rate, is allowed to all continental U.S. rail points or all U.S. highway points listed in published tariffs (Alaska and Hawaii excluded). In no case will more than actual freight be allowed. NOTE: All orders are accepted on the basis of prices in effect at the time of shipment. NOTIE: To the prices and terms quoted, there will be added any manufacturers or sales tax payable on the transaction under any effective statute. GENERAL UP numbers are available upon request. To obtain current ISO certifications, listings, and other approvals, visit Anvil s website at. Pricing is subject to change without notice. Go to Anvil s website for the most current list price information, or contact your local Anvil representative. LOSS OR DAMAGE LAIMS: All goods are shipped at buyer s risk. Shipments should be carefully examined upon delivery and before the carrier s delivery receipt is signed. If any loss or damage is evident, the buyer should make an appropriate notation on the delivery receipt and insist that the carrier s driver initial such exception. The contents of all packages should be carefully examined for concealed damage as soon as possible after delivery, so that the carrier can be requested, within 48 hours after delivery, to arrange for prompt inspection of the damaged goods. NORTHERN REGION TOMER SERVIE ENTER 800-301-2701 SOUTHERN REGION TOMER SERVIE ENTER 800-451-4414

STANDARD PRODUTS Price List 1. ONTROLLING PROVISIONS: These terms and conditions shall control with respect to any purchase order or sale of Seller s products. No waiver, alteration or modification of these terms and conditions whether on Buyer s purchase order or otherwise shall be valid unless the waiver, alteration or modification is specifically accepted in writing and signed by an authorized representative of Seller. 2. DELIVERY: Seller will make every effort to complete delivery of products as indicated on Seller s acceptance of an order, but Seller assumes no responsibility or liability, and will accept no backcharge, for loss or damage due to delay or inability to deliver caused by acts of God, war, labor difficulties, accident, delays of carriers, by contractors or suppliers, inability to obtain materials, shortages of fuel and energy, or any other causes of any kind whatever beyond the control of Seller. Seller may terminate any contract of sale of its products without liability of any nature, by written notice to Buyer, in the event that the delay in delivery or performance resulting from any of the aforesaid causes shall continue for a period of sixty (60) days. Under no circumstances shall Seller be liable for any special or consequential damages or for loss, damage, or expense (whether or not based on negligence) directly or indirectly arising from delays or failure to give notice of delay. 3. WARRANTY: Seller warrants for one year from the date of shipment Seller s manufactured products to the extent that Seller will replace those having defects in material or workmanship when used for the purpose and in the manner which Seller recommends. If Seller examination shall disclose to its satisfaction that the products are defective, and an adjustment is required, the amount of such adjustment shall not exceed the net sales price of the defective products only and no allowance will be made for labor or expense of repairing or replacing defective products or workmanship of damage resulting from the same. Seller warrants the products which it sells of other manufacturers to the extent of the warranties of their respective makers. Where engineering design or fabrication work is supplied. Buyer s acceptance of Seller s design or of delivery of work shall relieve Seller of all further obligation, other than expressed in Seller s product warranty. THIS IS SELLER S SOLE WARRANTY. SELLER MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED AND ALL IMPLIED WARRANTIES OF MERHANTABILITY AND FOR A PARTIULAR PURPOSE WHIH EXEED SELLER S AFORESTATED OBLIGATION ARE HEREBY DISLAIMED BY SELLER AND EXLUDED FROM THIS WARRANTY. Seller neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of its engineering designs or products. This warranty shall not apply to any products or parts of products which (a) have been repaired or altered outside of Seller s factory, in any manner: (b) have been subjected to misuse, negligence or accidents; (c) have been used in a manner contrary to Seller s instructions or recommendations. Seller shall not be responsible for design errors due to inaccurate or incomplete information supplied by Buyer or its representatives. 4. SELLER S LIABILITY: Seller will not be liable for any loss, damage, cost of repairs, incidental or consequential damages of any kind, whether based upon warranty (except for the obligation accepted by Seller under Warranty above), contract or negligence, arising in connection with the design, manufacture, sale, use or repair of the products or of the engineering designs supplied to Buyer. 5. RETURNS: Seller cannot accept return of any products unless its written permission has been first obtained, in which case same will be credited subject to the following (a) All material returned must, on its arrival at Seller s Plant, be found to be in first-class condition; if not, cost of putting in saleable condition will be deducted from credit memoranda; (b) A handling charge deduction of twenty percent (20%) will be made from all credit memoranda issued for material returned; (c) Transportation charges, if not prepaid will be deducted from credit memoranda. 6. SHIPMENTS: All products sent out will be carefully examined, counted and packed. The cost of any special packing or special handling caused by Buyer s requirements or requests shall be added to the amount of the order. No claim for shortages will be allowed unless made in writing within ten (10) days of receipt of a shipment. laims for products damaged or lost in transit should be made on the carrier, as Seller s responsibility ceases, and title passes, on delivery to the carrier. 7. SPEIAL PRODUTS: Orders covering special or nonstandard products are not subject to cancellation except on such terms as Seller may specify on application. 8. PRIES AND DESIGNS: Prices and designs are subject to change without notice. All prices are F.O.B. Point of shipment, unless otherwise stated. 9. TAXES: The amount of any sales, excise or other taxes, if any, applicable to the products covered by this order, shall be paid by Buyer unless Buyer provides Seller with an exemption certificate acceptance to the taxing authorities. 10. NULEAR PLANTS: Where the products, engineering design or fabrication is for nuclear plant applications. Buyer agrees (a) to take all necessary steps to add Seller as an insured under the American Nuclear Insurers (ANI) pool and under the Mutual Atomic Energy Reinsurance Pool (MAERP) for property damage and liability insurance and if necessary steps could have been taken, but are not taken, Buyer shall hold Seller harmless against all such losses which could have been thus covered (b) Buyer agrees to hold Seller harmless with respect to any personal injury (or death), property damage or other loss in a nuclear incident which is caused directly or indirectly by defective design, material, workmanship furnished by Buyer (or which could be so covered but with respect to which Buyer has elected to self-insure), and further agrees to waive subrogation by its carriers of such insurance against Seller, and (c) as to nuclear hazards for which Buyer cannot obtain insurance coverage, the liability of Seller for any personal injury (or death), property damage or other loss directly caused by defective design, material, or workmanship furnished by Seller shall not exceed the value at the time of the loss occurrence. 11. MINIMUM INVOIE: Domestic: $100 plus transportation. International: $500 plus transportation. 12. TERMS: ash, net 30 days unless otherwise specified. NOTE: All orders are accepted on the basis of prices in effect at the time of shipment. NOTIE: The prices and terms quoted, there will be added any manufacturers or sales tax payable on the transaction under any effective statute. FREIGHT ALLOWANE: All prices are F.O.B. point of shipment. On shipments weighing 2,500 pounds or more, rail freight or motor freight at the lowest published rate, is allowed to all continental U.S. rail points or all U.S. highway points listed in published tariffs (Alaska and Hawaii excluded). In no case will more than actual freight be allowed. Shipments (weighing less than 2,500 pounds) will be shipped prepaid. The buyer will be invoiced for freight costs at the applicable published class, exception or commodity rate(s) or charge(s). Anvil reserves the right to select the carrier for all shipments. 2

STANDARD PRODUTS Price List Standard Gaskets - Your order must specify gasket grade GRADE TEMPERATURE RANGE OMPOUND OLOR ODE E -40 F to +230 F EPDM Green EP -40 F to +250 F EPDM Green and Red T -20 F to +180 F Nitrile (Buna-N) Orange *GENERAL SERVIE APPLIATION Water, dilute acids, alkalies, salts and many chemical services not involving hydrocarbons, oils, or gases. Excellent oxidation resistance. NOT FOR E WITH HYDROARBONS. Water, dilute acids, alkalies, salts and many chemical services not involving hydrocarbons, oils, or gases. Excellent oxidation resistance. NOT FOR E WITH HYDROARBONS. Petroleum products, vegetable oils, mineral oils, and air contaminated with petroleum oils. NOT FOR E IN HOT WATER SERVIES. Special Gaskets GRADE TEMPERATURE RANGE OMPOUND OLOR ODE *GENERAL SERVIE APPLIATION O -20 F to +300 F Fluoro Elastomer Blue High-temperature resistance to oxidizing acids, petroleum oils, hydraulic fluids, halogenated hydrocarbons, and lubricants. L -40 F to +350 F Silicone Red Gasket Dry, hot air, and some high-temperature chemical services. E (type A) -40 F to +150 F Pre-Lubricated Violet Wet and Dry (oil-free air) pipe fire protection sprinkler systems. For dry pipe systems, Gruvlok Xtreme Lubricant is required. *ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. Additional gasket compounds and configurations are available contact an Anvil Representative. STANDARD LUBRIANT LUBRIANTS GRUVLOK DIAMETER TAPE Available upon request. ontact an Anvil representative for pricing. PRIE 2 lbs. Tb Std Gruvlok Lubricant $250.00/tub 5 Gallon Pail $2,092.00 QUIK DRY LUBRIANT 1 Quart an $252.50 XTREME LUBRIANT (SILIONE) 10 oz. Tube (1 each) $126.00 2.2 lbs. Tub (Gruvlok Lubricant) $435.00 STANDARD LUBRIANT AGE GUIDE NUMBER OF GASKETS SIZE OF GASKET PER TUBE PER QUART 2" 55 400 3" 45 300 4" 25 200 6" 20 130 8" 15 100 10" 10 85 12" 9 60 14" 7 50 16" 6 40 18" 5 35 20" 4 30 24" 3 20 XTREME LUBRIANT AGE GUIDE SIZE OF GASKET NUMBER OF GASKETS PER QUART 2" 1,200 3" 900 4" 600 6" 390 8" 300 10" 255 12" 180 14" 150 16" 120 18" 105 20" 90 24" 60 3

Table of ontents Terms and onditions...2 Gasket Selection...3 Standard Gaskets...3 Special Gaskets...3 Lubricants...3 Gruvlok Diameter Tape...3 Grooved-End ouplings... 7-14 Flexible oupling Fig. 7001...7 Standard oupling Fig. 7011...7 Lightweight Flexible oupling Fig. 7000...8 Hingelok oupling Fig. 7003...8 Rigidlok Rigid oupling Fig. 7401...9 Rigidlite 300 PSI oupling Fig. 7400...9 SlideLOK Rigid oupling Fig. 74...10 Reducing oupling Fig. 7010...10 SlideLOK Rigid oupling Fig. 7402...11 Outlet ouplings Fig. 7042F, 7042M and 7042G...11 HPR oupling Fig. 7004 HPR...12 End Guard oupling Fig. 7004 EG...12 Double Grooved oupling Fig. 7377...12 HDPE oupling Fig. 7305...13 HDPE Transition oupling Fig. 7307...13 Flange Adapter for HDPE Pipe Fig. 7312...13 Gruvlok 300# Flange Fig. 7013...13 Gruvlok Flange Fig. 7012...14 Gruvlok Flange Adapter Fig. 7788...14 Fittings for Grooved-End Pipe... 14-23 90 Elbows Fig. 7050...14 45 Elbows Fig. 7051...14 22½ Elbows Fig. 7052...15 11¼ Elbows Fig. 7053...15 Tees Fig. 7060...15 Tees with Threaded Branch Fig. 7063...15 Reducing Tee Fig. 7061...16 Reducing Tee with Threaded Branch Fig. 7064...17 oncentric Reducer (Gr x Gr) Fig. 7072...18 oncentric Reducer (Gr x Flg) Fig. 7072GF...18 Reducer Threaded Small End Fig. 7076...19 ap Fig. 7074...19 Hose Nipple Fig. 7086...19 Gruvring Fig. 7022...19 Eccentric Reducer Fig. 7073 & Fig. 7097...20 90 Long Radius Elbows Fig. 7050LR (1½"D)...21 Fig. 7050DR 90 Drain Elbow...21 Reducing Base Support Elbows Fig. 7050RF Grooved x Flanged (GxF)...21 45 Long Radius Elbows Fig. 7051 LR (1½"D)...21 Female Thread Adapter Fig. 7087...22 Bullhead Plug Fig.7075...22 Lateral Fig. 7069...22 Tee WYE Fig. 7066...22 Steel ross Fig. 7068 and True Y Fig. 7071...23 Reducing Lateral Fig. 7070...23

Table of ontents (continued) High Pressure Fittings...24 90 LR Elbow Fig. 7050 EG...24 45 LR Elbow Fig. 7051 EG...24 Tee Fig. 7060 EG...24 ross Fig. 7068 EG...24 Header Tee Fig. 7662EG...24 Valves and Accessories... 25-32 Grooved-End Butterfly Valve Series 7700...25 Gruvlok Butterfly Valves Fig. 8000GR...25 Gruvlok Ball Valves Fig. 7500...26 Grooved End Butterfly Valve Series 7600...26 Grooved End Butterfly Valve Fig. 70G...26 Gruvlok ircuit Balancing Valves Grooved End Straight GBV-G, End Angle Fig. GBV-A, & Flanged Fig. GBV-F...27 Grooved heck Valve Fig. 90G...27 End heck Valve Fig. 7800...27 Silent heck Valve Fig. 400G...27 Suction Diffuser Fig. 7250...28 AF21-GG Grooved x Grooved onnectors...28 AF21-GF Grooved x Flange onnectors...28 AF21-FF Flange x Flange onnectors...28 Gruvlok Air Vent GAV-15 & GAV-30...29 Grooved-End WYE Strainer Fig. 758G...29 Grooved-End WYE Strainer Fig. 768G...29 Grooved-End Strainer Fig. 7260...29 Fig. FTV-S (Straight) or Fig. FTV-A (Angle Body)...29 lamp-t Grooved Outlet Fig. 7046...30 lamp-t Female Threaded Outlet Fig. 7045...30 lamp-t ross Fig. 7047, Fig. 7048 and Fig. 7049...31 Adapter Flanges Fig. 7084 (150 lb.) & Fig. 7085 (300 lb.)...32 Spare Parts...32-34 Flange Parts for Fig. 7012 & 7013 Gruvlok Flanges...32 Flange Gaskets for Fig. 7012 & 7013 Gruvlok Flanges...33 Standard Gaskets for Fig. 7005 & 7305 ouplings...33 Plated Trackhead Bolts and Nuts...33 Standard Gaskets...33 Gaskets for Fig. 7004 EG...33 Reducing oupling Fig. 7010 (Gasket Only)...33 lamp-t Grooved Outlet Fig. 7046 (Gasket Only)...34 lamp-t Female Threaded Outlet Fig. 7045 (Gasket Only)...34 Plain-End...34 Plain-End oupling Roughneck oupling Fig. 7005...34 Gruvlok Advanced opper System...35 DI-LOK DI-Electric Nipple Fig. 7088 (Gr. x Th.)...35 DI-LOK DI-Electric Nipple Fig. 7089 (Gr. x Gr.)...35 DI-LOK DI-Electric Nipple Fig. 7090 (Th. x Th.)...35 DI-LOK DI-Electric Fitting Fig. 7091 (TS x IPS)...35 Red-White Valves...36 Hydronic Hook-up Kits...36 Red-White Valves...36 Hydronic Hook-up Kits...36

Table of ontents (continued) Roll Groovers...37 Model 1007/3007 Roll Groover...37 Expansion Joints for Grooved-End Pipe...38 Gruvlok Fig. 7240 Expansion Joint...38 TS opper System...39-41 Rigid oupling Fig. 6400...39 SlideLOK oupling Fig. 6402...39 90 Elbow Fig. 6050 (Gr x Gr)...39 45 Elbow Fig. 6051(Gr x Gr)...39 Tee Fig. 6060 (Gr x Gr x Gr)...39 Reducing Tee Fig. 6061 (Gr x Gr x Gr) & Fig. 6064 (Gr x Gr x up)...40 oncentric Reducer Fig. 6072 (Gr x Gr) & Fig. 6075 (Gr x up)...40 ap Fig. 6074...41 Flange Adapter Fig. 6084...41 Butterfly Valve Fig. 6700 Series...41 Specialty Fittings for Grooved-End Pipe...42-43 90 Adapter Elbows Fig. 7055...42 45 Adapter Elbows Fig. 7056...42 Reducing Tee Wyes Fig. 7067...42 Steel Swaged Nipples Figs. 7077, 7078, and 7079...43 Adapter Nipples Figs. 7080, 7081, and 7082...43 Plain End Adapter Nipples Figs. 7080P, 7081P, and 7082P...43 Plain-End Fittings (For use with Fig. 7005 oupling only)...44-45 90 Elbows Fig. 7050P...44 90 Long Radius Elbows Fig. 7050LRP...44 45 Elbows Fig. 7051P...44 45 Long Radius Elbows Fig. 7051LRP...44 Tee Fig. 7060P...44 ross Fig. 7068P...44 Lateral Fig. 7069P...44 True WYE Fig. 7071P...44 Bull Plug Fig. 7075P...44 Fabricated Steel Reducing Tees Fig. 7061P...45 Flange Nipples Fig. 7084P and 7085P...45 Stainless Steel Fittings and ouplings...46-49 Rigidlite oupling Fig. 7400SS...46 Flange Adapter Fig. 7084SS...46 90 Elbow Fig. 7050SS...47 45 Elbow Fig. 7051SS...47 aps Fig. 7074SS...47 Tees Fig. 7060SS...47 Reducing Tees Fig. 7061SS...48 oncentric Reducers Fig. 7072SS...48 Eccentric Reducers Fig. 7073SS...49 Grinnell Integrated Items...49-55 High Pressure Rigid oupling Fig. 770...49 Butterfly Valve Fig. B333...49 Low Profile Butterfly Valve Fig. B8101...50 Grooved Dual Disk heck Valve Fig. V890...50 Low Profile Butterfly Valve Fig. B8101...50 Grooved Ball Valve Fig. BV835...50 Grooved Butterfly Valve Fig. B8200L...50

Table of ontents (continued) Flange x Flange ircuit Balancing Valve Fig. B800...51 Groove x Flange ANSI Suction Diffuser Fig. S810...51 Groove x Groove ircuit Balancing Valve Fig. B800...51 Reducing oupling with Grade EN EPDM Gasket Fig. 616...52 Grooved 45 Elblow Fig. 601...52 Transition oupling for Joining IPS to opper Tubing Systems with Grade EN Fig. 617...52 Tee Fig. 619...52 Grooved 90 Elblow Fig. 610...52 ap Fig. 660...52 Grooved 45 Elblow Fig. 601...52 Grooved oncentric Reducer Fig. 650...53 Reducing Tee Grooved x Grooved Fig. 621...53 Grooved Reducer Grooved x up Fig. 652...53 Reducing Tee Grooved x Grooved x up Fig. 618...53 Rigid oupling 316 SS with Grade EN or T Gasket Fig. 472...54 Flexible oupling 316 SS with Grade EN or T Gasket Fig. 405...54 Rigid oupling 316 SS with Grade EN or T Tri-Seal Gasket Fig. 472...54 Flexible oupling 316 SS with Grade EN or T Tri-Seal Gasket Fig. 405...54 Stainless Steel Grooved Butterfly Valve EPDM or Nitrile Lever Operator Fig. B480...55 Stainless Steel Grooved Ball Valve (600) PSI Fig. BV435...55 ross Reference...56-58 Numerical Index...59

NOTES

ouplings for Grooved-End Pipe STANDARD PRODUTS Price List Flexible oupling Fig. 7001 Grooved-End ouplings Sizes 1"-14" Sizes 16"-24" Sizes 28" and 30" OUPLING OMPLETE WITH OUPLING OMPLETE WITH PIPE OUTSIDE EP OR T GASKET FLH GAP EP OR T DIAMETER () GASKET () EAH (LBS.) PAINTED GALV. PAINTED GALV. QTY. NO. SIZE 1 1.315 1.43 $59.50 $79.00 $91.50 $112.50-2 ³ ₈ x 2 ¼ All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. Number of bolts equals housing segments. Weights are approximate and subject to change. Grade O or L gaskets are available. ontact your Anvil representative for more details. Standard oupling Fig. 7011 PIPE OUTSIDE PIPE SIZE DIAMETER EAH (LBS.) EAH) PAINTED QTY. NO. SIZE 30 O.D. 30.000 200.00 $3,967.00 6 1¼ x 4³ ₈ Working pressure and end load values are for standard wall pipe. OUPLING OMPLETE WITH "E" EPDM GASKET (PRIE SPARE PARTS PLATED BOLT & NUT 1 ¼ 1.660 1.34 $78.00 $103.00 $112.50 $138.50-2 ³ ₈ x 2 ¼ 1 ½ 1.900 1.55 $84.50 $109.50 $117.50 $145.50-2 ³ ₈ x 2 ¼ 2 2.375 3.10 $90.00 $118.00 $123.00 $154.00-2 ½ x 3 2 ½ 2.875 3.50 $104.50 $145.50 $149.00 $189.50-2 ½ x 3 3 3.500 4.30 $116.00 $159.50 $154.50 $200.00-2 ½ x 3 3 ½ 4.000 4.31 $165.00 $231.50 - - - 2 ⁵ ₈ x 3 ½ 4 4.500 6.76 $167.00 $234.00 $222.00 $290.50-2 ⁵ ₈ x 3 ½ 5 5.563 9.60 $265.50 $359.50 $387.00 $502.00-2 ¾ x 4 ½ 6 6.625 11.81 $296.50 $424.50 $429.50 $562.50-2 ¾ x 4 ½ 8 8.625 20.29 $509.50 $757.00 $578.50 $793.00-2 ⁷ ₈ x 5 ½ 10 10.750 21.81 $782.50 $1,120.50 $928.00 $1,247.00-2 ⁷ ₈ x 5 ½ 12 12.750 26.78 $889.50 $1,272.00 $1,089.50 $1,433.50-2 ⁷ ₈ x 6 14 14.000 41.66 $924.50 $1,276.50 $867.50 $1,198.50-4 ⁷ ₈ x 5 ½ 16 16.000 50.00 $1,212.50 $1,645.50 $1,212.50 $1,645.50-4 1 x 4 18 18.000 71.65 $1,420.00 $1,967.50 $1,420.00 $1,967.50-4 1 x 4 20 20.000 80.00 $1,878.50 $2,518.50 $1,878.50 $2,518.50-4 1¹ ₈ x 4 ½ 24 24.000 90.00 $2,444.00 $3,281.50 $2,444.00 $3,281.50-4 1¹ ₈ x 4 ½ 28 28.875 105.00 POA POA - - - 6 1 x 5 ½ 30 31.000 137.00 POA POA - - - 6 1 x 5 ½ SPARE PARTS PLATED BOLT & NUT Tools Tools opper Method Plain-End Spare Parts Valves and Fittings Accessories 9

STANDARD PRODUTS Price List Grooved-End ouplings Lightweight Flexible oupling Fig. 7000 Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories PIPE SIZE PIPE OUTSIDE DIAMETER EAH (LBS.) OUPLING OMPLETE WITH E OR T GASKET () PIPE OUTSIDE DIAMETER EAH (LBS.) OUPLING OMPLETE WITH FLH GAP E OR T GASKET () PAINTED GALVANIZED PAINTED GALVANIZED OUPLING OMPLETE WITH EP OR T GASKET () OUPLING OMPLETE WITH FLH GAP EP OR T GASKET () SPARE PARTS PLATED BOLT & NUT SIZE 1 1.315 1.28 $60.00 $73.50 $94.50 $111.00-3/8 x 2¼ 1 ¼ 1.660 1.35 $61.00 $79.00 $98.50 $117.50 25 3/8 x 2¼ 1 ½ 1.900 1.44 $74.00 $91.50 $107.00 $128.50 20 3/8 x 2¼ 2 2.375 2.03 $90.00 $118.00 $111.00 $132.00 20 3/8 x 2¼ 2 ½ 2.875 2.29 $104.50 $145.50 $132.00 $155.50 20 3/8 x 2¼ 3 3.500 3.05 $116.00 $159.50 $139.00 $168.00 15 ½ x 2¾ 3 ½ 4.000 3.37 $142.00 $184.00 - - - ½ x 3 4 4.500 4.68 $167.00 $234.00 $198.50 $242.50 10 ½ x 3 5 5.563 6.13 $251.00 $359.50 $336.50 $400.50-5/8 x 3½ 6 6.625 8.63 $296.50 $424.50 $372.00 $451.00-5/8 x 3½ 8 8.625 14.00 $480.50 $714.00 $617.50 $740.00 - ¾ x 4½ All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. Number of bolts equals housing segments. Weights are approximate and subject to change. Grade O or L gaskets are available. ontact your Anvil representative for more details. Hingelok oupling Fig. 7003 PAINTED GALV. PAINTED GALV. 1 1.315 1.30 $138.50 - - - - 1 ¼ 1.660 1.40 $163.00 - - - - 1 ½ 1.900 1.66 $156.50 $187.00 $163.50 $193.50-2 2.375 2.13 $149.50 $163.50 $149.50 $187.00-2 ½ 2.875 3.11 $165.00 $196.50 $202.50 $242.50-3 3.500 3.51 $191.50 $235.00 $229.00 $277.50-4 4.500 5.08 $245.00 $314.50 $302.00 $374.50-5 5.563 9.42 $496.50 $608.50 $612.00 $747.50-6 6.625 11.12 $520.50 $658.50 $650.50 $792.50-8 8.625 17.83 $797.50 $998.50 $902.50 $1,113.00 - ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. 10

Rigidlok Rigid oupling Fig. 7401 STANDARD PRODUTS Price List Grooved-End ouplings PIPE OUTSIDE DIAMETER EAH (LBS.) Sizes 1¹/₂"-12" Sizes 14"-18" Sizes 20"-24" OUPLING OMPLETE WITH EP OR T GASKET () All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. Number of bolts equals housing segments. Weights are approximate and subject to change. ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. Rigidlite 300 PSI oupling Fig. 7400 PIPE OUTSIDE DIAMETER EAH (LBS) OUPLING OMPLETE WITH FLH GAP EP OR T GASKET () OUPLING OMPLETE WITH EP OR T GASKET () 7401-2 OUPLING OMPLETE WITH FLH GAP E OR T GASKET () OUPLING OMPLETE WITH FLH GAP EP OR T GASKET () SPARE PARTS PLATED BOLT & NUT PAINTED GALV. PAINTED GALV. PAINTED GALV. QTY. NO. SIZE 1 ½ 1.900 1.80 $80.00 $101.50 $112.50 $135.00 2 ³ ₈ x 2¼ 2 2.375 2.40 $88.50 $111.50 $120.50 $145.00 2 ³ ₈ x 2½ 2 ½ 2.875 2.90 $101.00 $127.00 $145.50 $170.50 2 ³ ₈ x 2¾ 3 3.500 3.60 $116.50 $148.50 $154.00 $188.50 2 ½ x 3 4 4.500 5.00 $162.00 $209.00 $214.50 $265.00 2 ½ x 3 5 5.563 6.90 $209.00 $272.00 $341.00 $599.50 2 ⁵ ₈ x 3½ 6 6.625 7.90 $274.00 $356.00 $401.50 $491.00 2 ⁵ ₈ x 3½ 8 8.625 15.90 $432.50 $562.50 $510.50 $640.00 2 ¾ x 4½ 10 10.750 25.60 $721.00 $963.00 $867.00 $1,102.00 2 1 x 6 12 12.750 30.50 $806.50 $1,079.50 $986.50 $1,268.00 2 ⁷ ₈ x 6 14 14.000 36.10 $897.50 $1,151.50 $893.50 $1,146.00 2 ⁷ ₈ x 5½ 16 16.000 40.80 $1,167.50 $1,491.00 $1,087.00 $1,387.00 $1,163.00 $1,399.50 3 ⁷ ₈ x 5½ 18 18.000 51.60 $1,244.00 $1,748.50 $1,255.50 $1,626.50 $1,343.50 $1,642.00 4 1 x 4 20 20.000 68.30 $1,715.50 $2,310.50 $1,715.50 $2,150.00 $1,836.00 $2,169.00 4 1 x 4 24 24.000 89.30 $2,364.50 $2,995.00 $2,199.50 $2,786.00 $2,353.00 $2,812.00 4 1 x 4 PLATED BOLT & NUT SIZE PAINTED GALV. PAINTED GALV. 1 1.315 1.21 $65.50 $79.00 $65.50 $79.00 - ³ ₈ x 2¼ 1 ¼ 1.660 1.36 $65.50 $79.00 $73.50 $82.00 25 ³ ₈ x 2¼ 1 ½ 1.900 1.32 $67.50 $80.00 $78.50 $90.50 20 ³ ₈ x 2¼ 2 2.375 1.82 $75.50 $88.50 $84.50 $97.50 20 ³ ₈ x 2¼ 2 ½ 2.875 1.82 $86.50 $104.00 $99.50 $116.00 20 ³ ₈ x 2¼ 3 3.500 2.67 $98.00 $120.00 $107.00 $125.50 15 ³ ₈ x 2¾ 4 4.500 3.57 $138.50 $165.50 $152.00 $177.00 10 ³ ₈ x 2¾ 5 5.563 4.60 $182.00 $217.00 $183.50 $296.50 - ½ x 3 6 6.625 5.20 $217.00 $250.50 $284.50 $331.00 - ½ x 3 8 8.625 9.45 $344.50 $418.00 $351.00 $533.50 - ½ x 3 All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. 11 Fittings opper Method Plain-End Spare Parts Valves and Accessories Tools Tools

STANDARD PRODUTS Price List SlideLOK Rigid oupling Fig. 74 Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories Reducing oupling Fig. 7010 Fig. 7010 oupling with Gasket EAH (LBS.) OUPLING OMPLETE WITH EP OR T GASKET () OUPLING BOLTS PAINTED GALV. GALV. SIZE 2 2.68 $89.00 $112.50 15 2 ½ x 23 ₄ 2 ½ 2.94 $102.00 $128.50 15 2 ½ x 23 ₄ 3 3.64 $117.50 $149.50 12 2 ½ x 3½ 4 4.86 $163.50 $211.50 10 2 ½ x 3½ 5 5.61 $211.50 $275.00 8 2 ½ x 3½ 6 6.37 $277.00 $359.50 6 2 ½ x 3½ 8 13.20 $436.50 $567.50-2 3/₄ x 4½ EAH (LBS.) OUPLING OMPLETE WITH E OR T GASKET () PAINTED GALV. PLATED BOLT & NUT SIZE 2 x 1 ½ 3.13 $118.50 $143.50 - ½ x 2¾ 2 ½ x 2 3.57 $154.00 $191.50 - ½ x 2¾ 3 x 2 4.30 $174.00 $220.00 - ½ x 2¾ 3 x 2 ½ 4.12 $151.50 $191.50 - ½ x 2¾ 4 x 2 8.90 $275.00 $345.50-5/8 x 3½ 4 x 2 ½ 7.37 $246.00 $323.50-5/8 x 3½ 4 x 3 6.69 $231.50 $297.50-5/8 x 3½ 5 x 4 7.30 $310.00 $405.50 - ¾ x 4½ 6 x 4 9.51 $465.50 $586.00 - ¾ x 4½ 6 x 5 8.30 $408.50 $528.50 - ¾ x 4½ 8 x 6 16.70 $695.00 $879.00 - ¾ x 4½ Note: Not recommended for Vacuum Service All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. Weights are approximate and subject to change. 12

STANDARD PRODUTS Price List SlideLOK Rigid oupling Fig. 7402 PIPE OUTSIDE DIAMETER EAH (LBS) OUPLING OMPLETE WITH EP OR T SLIDELOK GASKET () OUPLING BOLTS FIG 7402 SLIDELOK GASKET ONLY () PAINTED GALV. QTY. SIZE EP T 2 2.375 2.68 $89.00 $112.50 15 2 ½ x 2¾ $87.50 $87.50 2 ½ 2.875 2.94 $102.00 $128.50 15 2 ½ x 2¾ $107.00 $107.00 3 3.500 3.64 $117.50 $149.50 12 2 ½ x 3½ $101.00 $107.00 4 4.500 4.86 $163.50 $211.50 10 2 ½ x 3½ $135.50 $143.50 5 5.563 5.61 $211.50 $275.00 8 2 ½ x 3½ $237.50 $0.00 6 6.625 6.37 $277.00 $359.50 6 2 ½ x 3½ $243.50 $258.50 8 8.625 13.20 $436.50 $567.50-2 3/₄ x 4½ $267.00 $267.00 Grooved-End ouplings Fittings Outlet oupling Fig. 7042F, 7042M and 7042G PIPE SIZE 1 ½ 2 2 ½ 3 4 6 BRANH Grooved Outlet 7042G 7042G & 7042M EAH (LBS.) Male IPS Outlet 7042M ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. Female IPS Outlet 7042F 7042F GROOVED & MALE THREADED 7042F FEMALE THREADED BRANH WITH E OR T GASKET BRANH WITH E OR T GASKET () () PAINTED GALV. EAH (LBS.) PAINTED GALV. x ½ - - - 2.60 $156.50 $184.50 - x ¾ - - - 2.60 $156.50 $184.50 - x 1 - - - 2.60 $156.50 $184.50 - x ½ - - - 3.30 $159.50 $196.50 - x ¾ - - - 3.30 $159.50 $196.50 - x 1 3.30 $181.00 $239.50 3.30 $159.50 $196.50 - x ½ - - - 4.80 $245.00 $302.00 - x ¾ - - - 4.80 $245.00 $302.00 - x 1 - - - 4.80 $245.00 $302.00 - x 1 ¼ 8.60 $161.00 - - - - - x 1 ½ 8.60 $161.00 $312.00 - - - - x ¾ - - - 7.90 $235.50 $286.50 - x 1 7.90 $374.00 $455.00 7.90 $312.00 $389.00 - x 1 ½ 8.60 $374.00 $455.00 - - - - x ¾ - - - 9.90 $345.50 $429.50 - x 1 9.90 $361.00-11.00 $345.50 $429.50 - x 1 ½ 11.80 $362.50 $696.50 - - - - x 2 11.00 $513.00 $696.50 - - - - x 1 - - - 18.00 $691.00 $897.00 - x 1 ½ 18.00 $726.00-18.00 $691.00 $897.00 - x 2 18.00 $726.00 $1,007.00 - - - - Tools Tools opper Method Plain-End Spare Parts Valves and Accessories 13

STANDARD PRODUTS Price List Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories HPR oupling Fig. 7004 HPR (with Standard Gasket) PIPE OUTSIDE DIAMETER EAH (LBS.) OUPLING OMPLETE WITH EP OR T GASKET () PAINTED GALV. All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. Weights are approximate and subject to change. For pricing on spare parts see pages 30-32. Double Grooved oupling Fig. 7377 PLATED BOLT & NUT SIZE 2 2.375 3.90 $87.50 $126.00-5/8 x 2¾ 2 ½ 2.875 4.85 $100.50 $143.00-5/8 x 3½ 3 3.500 5.33 $111.50 $160.00-5/8 x 3½ 4 4.500 8.93 $162.00 $244.00 - ¾ x 4½ 5 5.563 13.95 $362.50 $449.00-7/8 x 5½ 6 6.625 16.10 $291.00 $443.00-7/8 x 5½ 8 8.625 28.00 $464.50 $707.50-1 x 5½ 10 10.750 39.20 $858.00 $1,244.00-1 x 6½ 12 12.750 43.90 $1,249.00 $1,878.00-1 x 6½ All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. End Guard oupling Fig. 7004 EG (with End Guard Gasket) PIPE OUTSIDE DIAMETER EAH (LBS.) Fig. 7004 EG with EG Gasket OUPLING OMPLETE WITH E OR T GASKET () PAINTED GALV. PLATED BOLT & NUT SIZE 2 2.375 3.56 $263.96 $327.52-5/8 x 2¾ 2 ½ 2.875 4.85 $281.91 $357.43-5/8 x 3½ 3 3.500 4.81 $293.89 $377.61-5/8 x 3½ 4 4.500 8.93 $429.22 $528.66 - ¾ x 4½ 6 6.625 15.09 $755.25 $933.97-7/8 x 5½ 8 8.625 25.10 $1,153.81 $1,567.32-1 x 5½ 10 10.750 39.20 $2,102.72 $3,222.88-1 x 6½ 12 12.750 51.00 $2,724.86 $3,831.55-1 x 6½ All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. ontact Anvil for specific service recommendations. Specify gasket grade when ordering. Use Gruvlok lubricant on gaskets. heck gasket color code to be certain it is recommended for the service intended. PIPE OUPLING OMPLETE OUPLING OMPLETE OUPLING OMPLETE PLATED OUTSIDE WITH END GUARD WITH -STYLE WITH FLH AP BOLT & DIAMETER T GASKET E OR T GASKET E GASKET NUT SIZE EAH (LBS) () () () 6 2.375 42.60 $3,730.00 $3,391.00 $3,730.00-1 x 5½ 8 2.875 72.00 $5,162.00 $4,694.50 $5,162.00-1½ x 6½ 10 3.500 98.30 $6,608.00 $6,009.50 $6,607.50-1½ x 6½ 14

STANDARD PRODUTS Price List ouplings for HPDE Pipe HDPE oupling Fig. 7305 HDPE Transition oupling Fig. 7307 Grooved-End ouplings PIPE SIZE PIPE OUTSIDE DIAMETER EAH (LBS.) EAH (LBS.) Weights are approximate and subject to change. *ontact your Anvil Representative for galvanized pricing. OMPLETE "E" OR "T" GASKET () Flange Adapter for HDPE Pipe, Fig. 7312 HDPE Flange omplete HDPE FLANGE OMPLETE WITH "E" OR "T" GASKET 4 15.00 $855.00-6 22.00 $1,202.00-8 26.00 $1,407.00-2 2.375 4.50 $523.00 12 3 3.500 8.50 $623.50 8 4 4.500 12.00 $685.00-6 6.625 18.00 $952.00-8 8.625 30.00 $1,115.00 2 10 10.750 43.00 $1,282.00-12 12.750 58.00 $1,477.00-14 14.000 86.30 $4,172.00-16 16.000 - $5,566.50-18 18.000 - $6,820.50 - HDPE Flange has ductile iron housing. Not supplied with flange bolts, nuts or gasket. *ontact your Anvil Representative for galvanized pricing. Gruvlok 300# Flange Fig. 7013 PIPE OUTSIDE DIAMETER PIPE OUTSIDE DIAMETER EAH (LBS.) EAH (LBS) OUPLING "E" OR "T" GASKET (PRIE EAH) BOLT SIZE 2 2.375 4.50 $569.00 15 ½ x 23/8 3 3.500 6.00 $665.50 12 ½ x 3 4 4.500 8.50 $776.50 4 ½ x 3 6 6.625 12.50 $1,066.50 3 5/8 x 3½ 8 8.625 20.50 $1,227.00 2 5/8 x 3½ 10 10.750 34.50 $1,692.00-7/8 x 5½ 12 12.750 42.50 $1,935.00-7/8 x 5½ Weights are approximate and subject to change. *ontact your Anvil Representative for galvanized pricing. OUPLING OMPLETE WITH E OR T GASKET () PAINTED GALV. 2 2.375 5.00 $433.00 $508.00-2 ½ 2.875 6.90 $500.50 $598.00-3 3.500 9.40 $684.00 $810.00-4 4.500 14.40 $909.00 $1,101.50-5 5.563 18.30 $1,034.50 $1,249.00-6 6.625 24.90 $1,202.50 $1,472.50-8 8.625 35.40 $1,378.50 $1,737.50-10 10.750 54.00 $2,193.50 $2,726.00-12 12.750 74.80 $2,341.50 $3,021.00 - The Gruvlok 300# Flange bolt hole pattern conforms to lass 300 steel, utilizing standard flange bolts. **Flange Sealing rings are recommended for use between wafer/lug type valves and Gruvlok flanges. Flange Bolts, Nuts and Gaskets not provided. Tools Tools opper Method Plain-End Spare Parts Valves and Fittings Accessories 15

Gruvlok Flange Fig. 7012 STANDARD PRODUTS Price List Gruvlok Flange Adapter Fig. 7788 Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories 16 PIPE SIZE HINGED PIPE SIZE PIPE OUTSIDE DIAMETER EAH (LBS.) EAH (LBS.) PAINTED OUPLING OMPLETE WITH E OR T GASKET () PAINTED GALV. GALV. 2* 2.375 4.05 $346.50 $419.00-2 ½* 2.875 4.68 $430.00 $528.50-3* 3.500 6.00 $464.00 $573.50-4* 4.500 6.51 $618.50 $766.50-5* 5.563 8.87 $718.00 $888.50-6* 6.625 9.53 $783.00 $973.50-8* 8.625 15.32 $884.50 $1,133.00-10* 10.750 18.26 $1,396.50 $1,774.00-12* 12.750 30.37 $1,826.00 $2,345.50 - FOUR PIEE 14* 14.000 52.50 $3,367.00 $4,142.00-16* 16.000 67.00 $3,908.00 $4,843.50-18* 18.000 82.50 $4,809.00 $6,128.00-20* 20.000 106.50 $5,786.00 $7,403.00-24* 24.000 138.50 $7,403.00 $9,550.50-90 Elbows Fig. 7050 Sizes 2"-12" Sizes 14"-24" Fittings for Grooved-End Pipe 1 0.57 $104.50 $138.00-1 ¼ 0.82 $104.50 $138.00-1 ½ 1.08 $104.50 $138.00-2 1.94 $104.50 $138.00-2 ½ 2.80 $104.50 $138.00-3 3.75 $183.50 $229.00-3 ½ 5.89 $212.00 $280.50-4 7.78 $199.50 $279.00-5 11.10 $474.00 $612.00-6 17.40 $557.00 $736.50-8 30.57 $1,157.00 $1,523.50-10 53.50 $2,140.50 $2,676.00-12 86.00 $3,127.50 $4,377.50 - For 14"-24" please see 7050LR list prices. Gruvlok fittings are full flow fittings made of ductile iron. Also available in 304 and 316 Stainless Steel. BOX QTY. PIPE SIZE PIPE SIZE PIPE OUTSIDE DIAMETER EAH (LBS.) EAH (LBS.) PAINTED () PAINTED GALV. GALV. 2 2.375 4.31 $256.00 $303.50-2 ½ 2.875 5.99 $325.00 $396.50-3 3.500 7.00 $344.00 $420.00-4 4.500 10.66 $450.50 $548.50-5 5.563 14.02 $500.50 $605.00-6 6.625 16.49 $500.50 $605.00-8 8.625 24.68 $673.00 $850.00-10* 10.750 36.84 $1,357.50 $1,632.00-12* 12.750 56.43 $2,048.00 $2,545.00-45 Elbows Fig. 7051 1 0.55 $104.50 $131.50-1 ¼ 0.75 $104.50 $131.50-1 ½ 0.84 $104.50 $131.50-2 1.42 $104.50 $131.50-2 ½ 1.85 $104.50 $131.50-3 2.73 $183.50 $216.00-3 ½ 4.57 $212.00 $280.50-4 5.39 $199.50 $258.50-5 9.00 $474.00 $587.00-6 10.95 $557.00 $703.00-8 19.58 $1,157.00 $1,451.00-10 33.71 $1,954.00 $2,313.50-12 50.00 $3,127.50 $3,954.50 - BOX QTY. NOTE: 10" and 12" Flange Adapters have a machine raised face. 2" through 8" Flange Adapters have a cast raised face. The Gruvlok Flange Adapter allows for direct connection of lass 125 or lass 150 flanged components to a grooved piping system. Ductile Iron conforming to ASTM A 536, Grade 65-45-12. For other coating requirements contact an Anvil Representative for more information. The Gruvlok Flange bolt hole pattern conforms to lass 150 steel and lass 125 cast iron flanges utilizing standard flange bolts. *Available with pn 10/16 bolt hole patterns. New Viton Gasket is POA Please check with an Anvil Sales Representative for more Information. Flange Sealing Rings are recommended for use between wafer/lug type valves and Gruvlok Flanges. For applications with wafer valves a latch bolt is recommended on both sides of the flange. (request extra latch bolt) Use: ³ ₈ x 2½ for 2"-6", ½ x 3½ for 8"-12" sizes. For 14"-24" please see 7051LR list prices. Gruvlok fittings are full flow fittings made of ductile iron. Also available in 304 and 316 Stainless Steel.

22¹/₂ Elbows Fig. 7052 EAH (LBS.) PAINTED GALV. 1* 0.50 $659.00 $681.00-1 ¼* 0.70 $115.50 $145.50-1 ½* 0.80 $115.50 $145.50-2 1.50 $115.50 $145.50-2 ½* 1.90 $115.50 $145.50-3 3.20 $165.00 $206.50-3 ½* 4.00 $384.00 $512.50-4 5.25 $218.00 $281.50-5* 7.20 $662.00 $799.00-6 11.00 $607.00 $772.00-8 17.70 $1,261.50 $1,567.50-10* 30.00 $1,664.00 $2,161.00-12* 40.40 $2,249.00 $2,788.00-14* 46.00 $2,017.50 $2,670.50-16* 52.20 $2,418.00 $3,387.00-18* 65.00 $2,928.50 $4,156.00-20* 80.00 $3,676.00 $5,776.00-24* 112.00 $6,271.50 $7,253.00 - (ast) STANDARD PRODUTS Price List *Gruvlok fittings are full flow fittings made of ductile iron except those marked (*) which are full flow 1¹/₂ D fabricated steel. Tees Fig. 7060 (Fabricated) 11¹/₄ Elbows Fig. 7053 EAH (LBS) PAINTED GALV. 1* 0.30 $261.00 $321.00-1 ¼* 0.50 $114.00 $144.00-1 ½* 0.70 $114.00 $144.00-2* 0.90 $263.50 $306.50-2 ½* 1.50 $263.50 $306.50-3* 2.00 $164.00 $203.00-3 ½* 2.80 $384.00 $448.50-4* 3.30 $201.50 $264.00-5* 5.00 $662.00 $771.50-6* 6.50 $607.00 $725.50-8* 10.00 $1,078.00 $1,269.00-10* 14.50 $1,554.00 $1,837.00-12* 18.70 $2,249.00 $2,697.50-14* 32.10 $1,825.00 $2,290.00-16* 42.00 $2,247.50 $2,995.00-18* 53.20 $2,721.00 $3,686.50-20* 65.70 $3,329.00 $4,611.50-24* 96.00 $5,807.50 $5,859.00 - Tees with Threaded Branch*, Fig. 7063 EAH (LBS) PAINTED GALV. EAH (LBS) PAINTED GALV. 1 1.02 $161.50 $210.00-1* 0.90 $246.50 $307.00-1 ¼ 1.27 $161.50 $210.00-1 ¼* 1.40 $339.00 $398.00-1 ½ 1.54 $161.50 $210.00-1 ½* 1.70 $528.00 $622.00-2 2.31 $161.50 $210.00-2* 2.90 $339.00 $398.00-2 ½ 3.97 $161.50 $210.00-2 ½* 4.70 $466.50 $559.50-3 5.74 $220.50 $301.50-3* 8.10 $466.50 $559.50-3 ½* 9.80 $891.50 $1,158.50-4* 13.50 $700.50 $962.00-4 10.42 $335.00 $455.00-5* 16.70 $2,011.50 $1,922.00-5 16.02 $780.00 $989.00-6* 25.60 $1,796.00 $2,112.50-6 25.20 $899.50 $1,227.00-8* 45.00 $2,048.00 $2,873.50-8 40.53 $1,969.50 $2,584.00-10* 73.00 $3,255.00 $4,690.00-10 74.47 $3,870.50 $5,341.50-12* 98.00 $4,883.50 $6,721.50-12 135.00 $5,299.00 $7,344.50 - *Gruvlok fittings are full flow fittings made of ductile iron except those marked (*) which 14* 118.00 $4,560.50 $5,679.00 - are full flow fabricated steel. 16* 146.00 $5,150.50 $6,541.00-18* 218.00 $6,438.00 $8,300.00-20* 275.00 $9,224.00 $11,693.50-24* 379.00 $14,061.50 $18,237.00 - *Gruvlok fittings are full flow fittings made of ductile iron except those marked (*) which are full flow fabricated steel. Also available in 304 and 316 Stainless Steel. 17 Grooved-End ouplings Fittings opper Method Plain-End Spare Parts Valves and Accessories Tools

Reducing Tees Fig. 7061 STANDARD PRODUTS Price List Grooved-End ouplings (ast) (Fabricated) Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories BRANH EAH (LBS) PAINTED GALV. 1 ¼ x 1 ¼ x 1* 1.50 $286.00 $325.00-1 ½ x 1 ½ x 1* 1.80 $397.50 $409.50 - x 1 ¼* 1.80 $302.00 $334.00 - x 1 2.59 $342.50 $400.50-2 x 2 x 1 ¼* 1.70 $426.50 $449.00 - x 1 ½ 2.70 $342.50 $406.50 - x 1* 4.10 $342.50 $400.50-2 ½ x 2 ½ x 1 ¼* 4.20 $515.50 $607.00 - x 1 ½* 4.30 $342.50 $406.50 - x 2* 4.40 $342.50 $406.50 - x 1* 7.00 $302.50 $385.50 - x 1 ¼* 5.80 $424.00 $560.00-3 x 3 x 1 ½* 5.90 $302.50 $389.00 - x 2* 5.91 $302.50 $389.00 - x 2 ½* 6.30 $302.50 $389.00 - x 1* 7.00 $406.50 $508.00 - x 1 ¼* 9.60 $799.00 $930.00-4 x 4 x 1 ½* 10.20 $406.50 $508.00 - x 2 10.30 $406.50 $533.00 - x 2 ½* 10.55 $406.50 $533.00 - x 3 10.40 $406.50 $533.00 - x 1* 13.60 $894.50 $1,101.00 - x 1 ¼* 13.50 $915.50 $1,133.50 - x 1 ½* 13.80 $1,135.50 $1,230.00-5 x 5 x 2* 14.00 $984.00 $1,215.50 - x 2 ½* 14.30 $802.00 $1,009.50 - x 3* 14.60 $802.00 $1,009.50 - x 4* 16.75 $867.50 $1,096.00 - x 1* 20.50 $1,078.00 $1,322.50 - x 1 ¼* 21.00 $1,102.50 $1,407.50 - x 1 ½* 21.00 $1,114.50 $1,525.00-6 x 6 x 2* 23.40 $955.50 $1,254.50 - x 2 ½ 23.20 $955.50 $1,254.50 - x 3 21.06 $955.50 $1,254.50 - x 4 22.10 $955.50 $1,254.50 - x 5 26.40 $955.50 $1,261.50 - x 2* 32.70 $1,376.00 $1,737.50 - x 2 ½* 33.00 $1,376.00 $1,737.50-8 x 8 x 3* 32.50 $1,482.50 $1,771.00 - x 4 38.09 $1,988.00 $2,597.00 - x 5* 34.70 $1,988.00 $2,597.00 - x 6 40.37 $1,988.00 $2,597.00-10 x 10 12 x 12 14 x 14 16 x 16 18 x 18 20 x 20 24 x 24 BRANH EAH (LBS) PAINTED GALV. x 2* 52.20 $2,207.00 $3,349.50 - x 2 ½* 52.60 $2,207.00 $2,781.00 - x 3* 53.00 $2,207.00 $3,510.50 - x 4* 53.60 $2,307.00 $2,948.00 - x 5* 54.20 $2,358.00 $3,010.00 - x 6* 55.00 $2,358.00 $3,828.00 - x 8* 64.70 $2,401.00 $3,846.50 - x 4* 75.10 $3,182.50 $4,476.00 - x 5* 75.60 $3,364.50 $4,370.00 - x 6* 76.20 $3,405.50 $4,995.50 - x 8* 76.30 $3,499.50 $5,292.00 - x 10* 77.60 $3,663.50 $5,695.50 - x 6* 101.00 $2,640.00 $3,386.50 - x 8* 103.00 $2,704.50 $3,442.00 - x 10* 104.00 $2,860.50 $3,646.50 - x 12* 105.00 $3,061.00 $3,920.00 - x 10* 129.00 $3,715.00 $4,706.00 - x 12* 130.00 $3,789.00 $4,813.50 - x 14* 132.00 $4,437.00 $5,517.00 - x 10* 194.00 $4,546.00 $5,855.00 - x 12* 196.00 $4,546.00 $5,912.00 - x 14* 201.00 $5,260.50 $6,763.00 - x 16* 203.00 $5,741.50 $7,251.50 - x 12* 246.00 $6,501.00 $8,302.00 - x 14* 248.00 $7,002.50 $8,914.00 - x 16* 250.00 $7,511.50 $9,521.50 - x 18* 252.00 $8,260.00 $10,443.00 - x 16* 342.00 $10,705.50 $14,677.00 - x 18* 345.00 $10,904.00 $14,979.00 - x 20* 347.00 $11,837.50 $17,356.50 - *Gruvlok fittings are full flow fittings made of ductile iron except those marked (*) which are fabricated steel. Also available in 304 and 316 Stainless Steel. 18

Reducing Tee with Threaded Branch Fig. 7064 STANDARD PRODUTS Price List (ast) (Fabricated) Grooved-End ouplings 2 x 2 2 ½ x 2 ½ 3 x 3 4 x 4 5 x 5 6 x 6 BRANH EAH (LBS) PAINTED GALV. x ¾* 1.60 $396.50 $465.50 - x 1 2.60 $361.50 $424.00 - x 1 ¼* 1.70 $607.00 $649.00 - x 1 ½* 2.70 $361.50 $423.00 - x 1* 4.10 $342.50 $424.00 - x 1 ¼* 3.50 $787.50 $809.50 - x 1 ½* 4.30 $361.50 $429.50 - x 2* 4.40 $361.50 $433.00 - x ¾* 5.70 $661.50 $702.00 - x 1 5.75 $361.50 $451.50 - x 1 ¼* 6.00 $889.50 $945.50 - x 1 ½* 5.30 $361.50 $454.50 - x 2* 5.50 $361.50 $454.50 - x 2 ½* 5.80 $869.00 $940.50 - x ¾* 7.20 $959.50 $1,181.50 - x 1* 7.00 $451.50 $555.00 - x 1 ¼* 8.00 $926.50 $998.00 - x 1 ½* 9.20 $451.50 $565.50 - x 2* 10.20 $451.50 $565.50 - x 2 ½* 11.20 $451.50 $582.00 - x 3* 11.40 $451.50 $582.00 - x 2* 14.50 $964.50 $1,050.50 - x 2 ½* 15.00 $866.50 $1,097.00 - x 3* 16.10 $802.00 $1,009.50 - x 4* 17.90 $866.50 $1,181.50 - x 2* 26.40 $1,124.00 $1,400.00 - x 2 ½* 26.50 $1,124.00 $1,400.00 - x 3* 26.50 $1,125.00 $1,400.00 - x 4* 26.50 $1,421.00 $1,528.00 - x 5* 28.00 $1,125.00 $1,400.00-8 x 8 10 x 10 12 x 12 14 x 14 16 x 16 18 x 18 24 x 24 BRANH EAH (LBS) PAINTED GALV. x 2* 37.50 $1,376.00 $1,897.50 - x 2 ½* 37.90 $1,363.50 $1,843.00 - x 3* 38.70 $1,897.50 $2,460.50 - x 4* 50.00 $1,988.00 $2,569.00 - x 5* 41.00 $1,988.00 $2,584.00 - x 6* 54.00 $2,199.50 $3,021.00 - x 2* 61.80 $2,305.00 $3,367.00 - x 3* 63.00 $2,305.00 $2,859.00 - x 4* 64.00 $2,411.00 $3,081.50 - x 5* 65.10 $2,120.00 $3,145.50 - x 6* 55.00 $2,465.00 $3,187.50 - x 8* 64.70 $3,323.00 $3,714.50 - x 3* 84.90 $3,104.50 $4,007.00 - x 4* 85.80 $3,326.50 $4,271.00 - x 5* 87.00 $3,512.50 $4,566.50 - x 6* 88.30 $3,558.50 $4,609.00 - x 8* 91.20 $3,658.50 $4,715.50 - x 10* 94.80 $3,828.00 $4,722.50 - x 8* 110.00 POA POA - x 10* 114.00 POA POA - x 12* 117.00 POA POA - x 8* 135.00 POA POA - x 10* 139.00 POA POA - x 12* 142.00 POA POA - x 10* 204.00 POA POA - x 12* 209.00 POA POA - x 14* 211.00 POA POA - x 16* 216.00 POA POA - x 8* 334.00 POA POA - x 10* 342.00 POA POA - x 12* 349.00 POA POA - opper Method Plain-End Spare Parts Valves and Fittings Accessories * Gruvlok fittings are full flow fittings made of ductile iron except those marked (*) which are fabricated steel. Tools 19

STANDARD PRODUTS Price List oncentric Reducer Fig. 7072, Groove by Groove (Gr x Gr) Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories 20 (ast) EAH (LBS.) (Weld) PAINTED GALV. 1 ¼ x 1* 0.60 $492.00 $541.00-1 ½ x 1* 0.60 $123.50 $145.00 - x 1 ¼* 0.60 $123.50 $145.00 - x 1 0.66 $123.50 $145.00-2 x 1 ¼ 0.74 $135.00 $157.50 - x 1 ½ 0.75 $123.50 $145.00 - x 1* 1.00 $167.50 $192.50-2 ½ x 1 ¼* 1.00 $123.50 $145.00 - x 1 ½* 1.30 $123.50 $145.00 - x 2 1.07 $123.50 $145.00 - x 1* 1.20 $135.00 $157.00 - x 1 ¼* 1.30 $214.00 $246.50-3 x 1 ½* 1.30 $148.00 $180.00 - x 2 1.40 $109.50 $132.50 - x 2 ½ 1.56 $148.00 $178.50-3 ½ x 3* 1.50 $157.00 $189.00 - x 1* 2.20 $163.00 $200.00 - x 1 ¼* 2.20 $1,237.00 $1,386.50 - x 1 ½* 2.30 $318.00 $350.50-4 x 2 2.25 $145.00 $177.50 - x 2 ½ 2.41 $178.50 $217.00 - x 3 2.42 $178.50 $217.00 - x 3 ½* 3.60 $178.50 $217.00 - x 2* 4.60 $1,739.50 $1,921.00-5 x 2 ½* 4.50 $413.00 $449.50 - x 3* 4.40 $206.50 $255.00 - x 4 4.04 $245.50 $307.00 - x 1* 6.80 $325.00 $405.00 - x 1 ½* 6.90 $1,928.50 $2,198.50 - x 2 4.70 $325.00 $405.00-6 x 2 ½* 6.00 $361.50 $444.00 - x 3 5.40 $325.00 $405.00 - x 4 5.66 $285.00 $367.50 - x 5 6.70 $419.00 $519.50 - *Gruvlok fittings are full flow fittings made of ductile iron except those marked (*) which are fabricated steel. Also available in 304 and 316 Stainless Steel. 8 10 12 14 16 18 20 24 EAH (LBS) EAH (LBS) PAINTED GALV. x 3* 12.00 $578.00 $719.50 - x 4 10.10 $578.00 $719.50 - x 5* 11.50 $578.00 $727.00 - x 6 11.00 $733.00 $917.50 - PAINTED 3 x 2 1.60 $835.00-4 x 2 2.50 $1,110.00-4 x 2 ½ 2.60 $1,005.00-4 x 3 2.60 $934.50-5 x 3 4.50 $1,643.00-5 x 4 4.50 $1,444.00-6 x 4 7.10 $1,250.00-6 x 5 7.40 $1,373.50-8 x 6 12.60 $1,573.50 - x 4* 20.00 $1,314.00 $1,618.00 - x 5* 20.00 $2,890.00 $3,297.50 - x 6 17.43 $1,438.00 $1,791.00 - x 8* 23.90 $1,438.00 $1,822.00 - x 4* 29.00 $6,288.00 $7,483.00 - x 6* 29.00 $1,714.00 $2,118.00 - x 8* 29.00 $2,570.00 $3,034.50 - x 10* 32.40 $2,570.00 $3,181.50 - x 6* 54.30 $7,537.00 $8,516.00 - x 8* 54.50 $4,273.00 $4,727.50 - x 10* 55.70 $3,735.00 $4,167.00 - x 12* 57.30 $4,087.50 $4,609.50 - x 8* 65.40 $6,119.50 $6,673.00 - x 10* 66.70 $5,881.00 $6,673.00 - x 12* 68.10 $5,960.00 $6,711.50 - x 14* 76.00 $5,960.00 $6,794.00 - x 10* 82.30 $8,161.00 $10,560.00 - x 12* 83.60 $8,380.00 $10,937.50 - x 14* 86.20 $6,785.50 $8,548.00 - x 16* 87.20 $6,785.50 $8,548.00 - x 10* 123.00 $12,014.00 $14,461.00 - x 12* 125.00 $9,130.00 $11,065.00 - x 14* 129.00 $9,167.00 $11,085.50 - x 16* 131.00 $7,379.00 $9,092.00 - x 18* 133.00 $7,103.00 $12,172.00 - x 10* 147.00 $26,767.50 $28,621.00 - x 12* 149.00 $26,121.50 $28,621.00 - x 14* 152.00 $22,711.50 $24,348.50 - x 16* 153.00 $17,521.00 $25,386.50 - x 18* 154.00 $16,764.50 $20,236.00 - x 20* 155.00 $13,490.00 $16,979.00 - oncentric Reducer Fig. 7072GF, Groove by Flange (Gr x Flg)

ap Fig. 7074 STANDARD PRODUTS Price List oncentric Reducer Fig. 7076 Groove by Thread (Gr x Thd) Grooved-End ouplings EAH (LBS) PAINTED GALV. 1 0.31 $90.00 $106.50-1 ¼ 0.42 $90.00 $106.50-1 ½ 0.53 $90.00 $106.50-2 0.50 $90.00 $106.50-2 ½ 0.72 $90.00 $106.50-3 1.09 $90.00 $106.50-3 ½ 1.50 $96.50 $126.00-4 2.46 $96.50 $126.00-5 3.74 $222.50 $297.50-6 6.77 $222.00 $297.50-8 12.34 $423.00 $560.00-10 21.62 $888.50 $1,156.50-12 33.72 $1,451.50 $1,847.50-14* 40.00 $2,343.00 $2,681.50-16* 45.00 $2,650.50 $3,165.00-18* 58.00 $3,067.50 $3,625.00-20* 79.00 $3,483.00 $4,160.50-24* 100.00 $4,743.00 $5,485.00 - *Machined dome cap. Fig. 7074T ½", ¾", and 1" tap options available. Also available in 304 and 316 Stainless Steel. Hose Nipple Fig. 7086 Groove by Hose (Gr x Hose) EAH (LBS) PAINTED GALV. 1 0.40 $208.50 $248.00-1 ¼ 0.70 $208.50 $248.00-1 ½ 0.80 $208.50 $248.00-2 1.30 $208.50 $248.00-2 ½ 2.10 $208.50 $248.00-3 3.30 $300.00 $361.00-4 5.50 $519.00 $624.00-5 8.10 $783.00 $975.50-6 13.20 $930.00 $1,179.50-8 24.00 $1,929.50 $2,588.50-10 29.00 $1,895.00 $2,654.50-12 46.00 $2,237.50 $2,959.00 - EAH (LBS) EAH (LBS) PAINTED GALV. 1 ½ x 1*.60 $128.50 $157.00 - x ¾* 1.00 $128.50 $157.00-2 x 1* 0.80 $128.50 $157.00 - x 1 ¼* 1.30 $128.50 $157.00 - x 1 ½* 1.30 $128.50 $157.00 - x 1* 1.00 $173.00 $199.00-2 ½ x 1 ¼* 1.00 $181.00 $222.50 - x 1 ½* 1.30 $189.50 $222.50 - x 2* 1.20 $128.50 $157.00 - x ¾* 1.20 $911.00 $969.50 - x 1* 1.20 $139.00 $168.00-3 x 1 ¼* 1.30 $157.00 $168.00 - x 1 ½* 1.30 $157.00 $188.00 - x 2* 1.30 $157.00 $188.00 - x 2 ½* 1.50 $189.50 $222.50 - x 1* 2.20 $179.50 $217.00 - x 1 ¼* 2.20 $929.00 $953.00-4 x 1 ½* 2.30 $417.50 $545.50 - x 2* 2.40 $190.50 $228.00 - x 2 ½* 2.30 $191.50 $234.50 - x 3* 2.60 $234.00 $276.50-5 x 4* 4.50 $1,319.50 $1,434.50 - x 1* 6.00 $361.50 $444.00 - x 1 ¼* 6.00 $336.50 $459.50-6 x 1 ½* 6.10 $336.50 $459.50 - x 2* 6.00 $361.50 $444.00 - x 3* 6.00 $361.50 $444.00 - x 4* 5.90 $2,166.00 $2,398.50 - *Fabricated Steel Reducer sizes not shown, will be priced on application. Gruvring Fig. 7022 PAINTED GALV. 30 250.00 $5,769.00 $6,922.50-36 290.00 $6,922.50 $8,307.00-42 345.00 $8,907.50 $10,688.50-48 580.00 $9,876.00 $11,851.50-54 650.00 $12,922.00 $15,506.00-60 750.00 $16,798.00 $20,158.00 - Tools opper Method Plain-End Spare Parts Valves and Fittings Accessories 21

Eccentric Reducer Fig. 7073 and Figure 7097 STANDARD PRODUTS Price List Grooved-End ouplings Fig. 7073 GR x GR (Fabricated) Fig. 7097 GR x THD (Fabricated) Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories EAH (LBS) PAINTED GALV. 1 ¼ x 1 1.50 $542.50 $678.50 - x ¾ 1.60 $602.50 $691.50-1 ½ x 1 1.70 $519.00 $607.50 - x 1 ¼ 4.50 $507.50 $634.00 - x ¾ 2.10 $1,151.00 $1,353.00-2 x 1 2.20 $571.50 $641.50 - x 1 ¼ 2.40 $624.00 $772.00 - x 1 ½ 2.50 $128.50 $151.50 - x 1 3.20 $1,345.50 $1,490.00-2 ½ x 1 ¼ 3.40 $623.50 $712.00 - x 1 ½ 3.60 $623.50 $712.00 - x 2 4.00 $255.00 $346.50 - x 1 4.00 $1,444.00 $1,587.50 - x 1 ¼ 4.30 $1,307.50 $1,497.50-3 x 1 ½ 4.50 $718.00 $840.50 - x 2 4.80 $290.50 $397.00 - x 2 ½ 5.60 $290.50 $406.00-3 ½ x 3 6.60 $1,585.50 $1,986.50 - x 1 5.90 $2,921.00 $3,257.50 - x 1 ½ 6.40 $1,767.50 $1,908.00-4 x 2 6.70 $355.00 $495.00 - x 2 ½ 7.30 $355.00 $495.00 - x 3 7.90 $355.00 $495.00 - x 2 9.30 $1,948.50 $2,367.50-5 x 2 ½ 9.90 $1,661.50 $2,068.50 - x 3 10.70 $1,605.50 $1,789.00 - x 4 11.90 $480.50 $678.50 - x 1 12.00 $3,025.00 $3,285.50 - x 2 12.20 $2,760.00 $3,005.00-6 x 2 ½ 12.80 $3,285.50 $3,576.50 - x 3 13.60 $639.00 $895.50 - x 4 14.90 $560.00 $822.50 - x 5 16.20 $671.50 $951.00 - EAH (LBS) PAINTED GALV. x 3 17.90 $3,205.50 $3,491.00-8 x 4 19.70 $2,803.00 $3,198.50 - x 5 21.40 $2,803.00 $3,198.50 - x 6 23.20 $1,129.50 $1,537.00 - x 4 29.70 $5,138.50 $5,934.00-10 x 5 31.70 $4,840.00 $5,485.50 - x 6 34.00 $3,650.50 $4,167.50 - x 8 34.40 $3,091.00 $3,701.50 - x 6 45.20 $4,875.50 $5,656.50-12 x 8 47.70 $4,752.50 $5,476.00 - x 10 52.00 $4,098.50 $4,859.00 - x 6 78.00 $9,204.50 $10,954.50-14 x 8 80.00 $6,970.50 $7,954.00 - x 10 84.00 $6,375.00 $6,972.50 - x 12 88.00 $6,192.50 $6,773.00 - x 8 91.00 $10,166.00 $14,841.50-16 x 10 96.00 $9,392.50 $13,739.50 - x 12 99.00 $9,238.00 $10,104.50 - x 14 104.00 $9,042.50 $10,935.00 - x 10 110.00 $12,775.50 $18,651.50-18 x 12 113.00 $11,996.00 $13,795.50 - x 14 117.00 $10,899.50 $13,182.50 - x 16 121.00 $10,899.50 $13,755.00 - x 10 145.00 $21,690.00 $25,983.50 - x 12 149.00 $12,453.00 $18,670.50-20 x 14 152.00 $12,795.00 $18,354.00 - x 16 156.00 $12,355.50 $14,944.00 - x 18 160.00 $12,355.50 $15,593.50 - x 12 174.00 $31,075.50 $38,844.00 - x 14 184.00 $20,766.50 $25,958.50-24 x 16 189.00 $20,766.50 $25,958.50 - x 18 194.00 $19,586.50 $23,093.00 - x 20 199.00 $19,821.00 $24,478.50 - All fabricated steel. Reducer sizes not shown will be priced on application. Fig. 7073 is also available in 304 and 316 Stainless Steel. 22

90 Long Radius Elbows Fig. 7050 LR (1¹/₂"D) EAH (LBS) PAINTED GALV. 1 0.09 $238.00 $311.00-1 ¼ 1.30 $238.00 $311.00-1 ½ 1.70 $238.00 $311.00-2 2.50 $238.00 $311.00-2 ½ 4.90 $297.00 $341.50-3 6.50 $238.00 $311.00-3 ½ 9.70 $400.00 $437.00-4 11.50 $353.00 $471.00-5 20.90 $1,785.00 $2,045.50-6 29.10 $1,022.50 $1,342.00-8 59.20 $2,441.00 $3,120.00-10 104.00 $5,053.00 $6,090.00-12 147.00 $5,105.50 $6,774.50-14 169.00 $3,531.50 $4,581.50-16 222.00 $4,584.50 $5,929.00-18 280.00 $5,819.00 $7,252.50-20 344.00 $7,669.00 $9,516.00-24 490.00 $11,106.00 $13,825.50 - All fabricated steel fittings. Reducing Base Support Elbows Fig. 7050RF Grooved x Flanged (G x F) EAH (LBS) BLAK 5 x 4 33.00 $2,055.00-6 x 4 38.50 $1,886.50-6 x 5 45.40 $2,136.00-8 x 5 65.50 $3,028.00-8 x 6 73.00 $2,867.50-10 x 6 100.00 $4,534.00-10 x 8 127.00 $4,293.50-12 x 8 155.00 $7,399.00-12 x 10 186.00 $7,399.00 - All fabricated steel fittings. STANDARD PRODUTS Price List 45 Long Radius Elbows Fig. 7051 LR (1¹/₂"D) All fabricated steel fittings. 90 Drain Elbows Fig. 7050DR EAH (LBS) PAINTED GALV. 1 0.70 $206.50 $261.00-1¼ 1.00 $206.50 $261.00-1½ 1.20 $206.50 $261.00-2 1.70 $206.50 $261.00-2½ 2.90 $658.00 $739.00-3 4.30 $206.50 $261.00-3½ 5.00 $437.00 $400.00-4 7.20 $251.00 $333.00-5 12.20 $1,658.00 $1,820.00-6 17.40 $733.50 $940.00-8 34.00 $1,274.50 $1,656.00-10 57.40 $3,790.50 $4,322.50-12 82.60 $4,388.50 $5,388.00-14 92.00 $2,644.50 $3,385.00-16 117.00 $2,976.00 $3,694.00-18 146.00 $3,488.50 $4,275.50-20 179.00 $4,581.50 $5,632.00-24 255.00 $6,959.00 $8,573.00 - EAH (LBS) PAINTED GALV. 1 ¼ 1.50 $245.00 $314.50-1 ½ 1.75 $245.00 $314.50-2 2.76 $245.00 $314.50-2 ½ 4.33 $245.00 $314.50-3 5.60 $312.50 $373.00-4 8.80 $317.50 $430.50-5 13.00 $1,061.00 $1,203.50-6 18.77 $555.00 $790.00-8 32.64 $1,078.00 $1,274.00 - All fabricated steel fittings. 10" and 12" available. ontact your Anvil representative for pricing. Grooved-End ouplings Fittings opper Method Plain-End Spare Parts Valves and Accessories Tools 23

STANDARD PRODUTS Price List Tee WYE Fig. 7066 Lateral Fig. 7069 Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories EAH (LBS) LENGTH PAINTED GALV. 2 x 2 x 2 6.40 $1,084.00 $1,291.00-2 ½ x 2 ½ x 2½ 11.50 $1,084.00 $1,291.00-3 x 3 x 3 16.50 $1,243.00 $1,499.50-3 ½ x 3 ½ x 3½ 22.00 $1,690.00 $2,177.00-4 x 4 x 3 23.00 $1,497.00 $1,811.50 - x 4 26.00 $1,725.00 $2,097.00 - x 3 32.00 $2,166.50 $2,539.00-5 x 5 x 4 35.00 $2,496.50 $2,787.50 - x 5 40.00 $3,668.00 $4,480.00 - x 3 50.00 $1,774.00 $2,290.50-6 x 6 x 4 55.00 $2,162.00 $2,702.00 - x 5 58.00 $3,116.00 $4,106.00 - x 6 60.50 $3,288.50 $4,066.50 - x 3 100.00 $2,112.50 $3,068.00 - x 4 110.00 $2,517.00 $3,468.50-8 x 8 x 5 111.00 $3,330.50 $4,381.00 - x 6 112.00 $3,632.50 $4,750.00 - x 8 120.00 $5,004.50 $6,345.00 - x 3 130.00 $2,802.50 $3,884.50 - x 4 135.00 $3,073.00 $4,219.50-10 x 10 x 5 140.00 $4,242.50 $5,146.50 - x 6 145.00 $4,075.50 $5,406.50 - x 8 150.00 $5,287.00 $6,801.50 - x 10 190.00 $6,904.50 $8,853.00-12 x 12 x 2 240.00 $9,519.00 $12,086.00 - Gruvlok Tee Wyes and Reducing Tee Wye s are fabricated steel. Bullhead Plug Fig. 7075 Galvanized and other sizes priced on application. Fabricated steel. EAH (LBS.) BLAK 2 2.50 $318.00-2 ½ 3.10 $318.00-3 4.40 $464.50-4 7.40 $598.00-5* 12.50 $1,300.00-6 18.50 $1,401.50 - EAH (LBS) PAINTED GALV. 1 1.50 $656.50 $857.50-1 ¼ 2.50 $624.00 $857.50-1 ½ 3.50 $656.50 $857.50-2 4.50 $624.00 $764.00-2 ½ 10.00 $624.00 $764.00-3 11.00 $689.00 $867.50-3 ½ 14.00 $959.50 $1,285.50-4 18.30 $1,059.00 $1,319.50-5 30.00 $1,546.50 $1,941.50-6 46.60 $2,488.50 $2,989.00-8 82.80 $3,580.50 $4,339.50-10 127.00 $4,865.00 $5,643.00-12 165.00 $5,880.50 $7,451.00-14 215.00 $6,696.00 $8,590.50-16 345.00 $8,364.00 $10,743.00-18 425.00 $9,349.00 $12,152.00-20 517.00 $14,179.50 $17,967.00-24 940.00 $22,031.00 $25,672.00 - Gruvlok Laterals are fabricated steel. Female Thread Adapter Fig. 7087 END TO END LENGTH EAH (LBS) PAINTED GALV. 1 2 1/16 0.70 $578.00 $620.00-1 ¼ 2 5/16 1.40 $305.50 $342.50-1 ½ 2 5/16 1.50 $395.50 $422.00-2 2 ½ 1.60 $188.00 $220.00-2 ½ 2 ¾ 1.60 $188.00 $220.00-3 2 ¾ 2.50 $218.00 $265.00-4 3 ¼ 4.50 $331.50 $416.50 - All fabricated steel fittings. 24

Steel ross Fig. 7068 & True Y Fig. 7071 STANDARD PRODUTS Price List STEEL ROSS TRUE Y EAH (LBS) PAINTED GALV. EAH (LBS) PAINTED GALV. 1 1.30 $391.50 $451.00-1.30 $598.50 $795.50-1 ¼ 2.10 $470.00 $547.00-2.10 $598.50 $796.00-1 ½ 2.50 $506.00 $586.50-2.50 $598.50 $712.00-2 2.90 $289.50 $344.50-2.90 $598.50 $712.00-2 ½ 5.20 $289.50 $344.50-5.20 $598.50 $712.00-3 7.50 $514.00 $629.00-7.50 $715.50 $850.50-3 ½ 9.80 $1,032.00 $1,230.00-9.80 $805.50 $1,102.50-4 12.20 $851.50 $1,048.00-12.20 $936.50 $1,125.50-5 17.60 $1,735.00 $2,090.00-17.60 $1,339.50 $1,607.50-6 28.30 $2,225.50 $2,701.50-28.30 $1,653.00 $2,013.50-8 48.00 $2,932.00 $3,627.00-48.00 $2,380.00 $2,925.00-10 70.00 $4,808.50 $5,948.00-70.00 $3,952.00 $4,840.50-12 110.00 $6,939.00 $8,644.00-110.00 $4,364.50 $5,520.50-14 140.00 $5,924.50 $8,106.50-140.00 $4,094.50 $5,110.00-16 170.00 $8,540.50 $9,858.00-170.00 $5,689.00 $6,794.00-18 260.00 $10,417.50 $12,038.00-260.00 $6,633.50 $8,098.50-20 320.00 $12,432.00 $17,873.00-320.00 $8,876.00 $10,985.00-24 585.00 $18,059.50 $25,205.50-585.00 $15,826.50 $16,678.50 - Reducing Lateral Fig. 7070 3 x 3 4 x 4 5 x 5 6 x 6 8 x 8 10 x 10 (Fabricated) LENGTH EAH (LBS) PAINTED GALV. x 2 9.80 $540.50 $674.00 - x 2 ½ 11.50 $540.50 $766.50 - x 2 15.50 $1,059.00 $1,261.50 - x 2 ½ 17.00 $1,059.00 $1,317.50 - x 3 18.50 $1,059.00 $1,317.50 - x 2 22.50 $1,546.50 $2,126.00 - x 3 26.50 $1,546.50 $1,917.50 - x 4 30.50 $1,546.50 $1,948.00 - x 2 30.50 $1,995.50 $2,496.50 - x 3 37.00 $1,995.50 $2,496.50 - x 4 40.00 $1,995.50 $2,514.00 - x 5 45.00 $1,995.50 $2,541.00 - x 4 59.60 $2,879.00 $3,653.50 - x 5 68.00 $2,879.00 $3,686.00 - x 6 75.00 $2,879.00 $3,730.50 - x 4 83.00 $3,150.00 $4,138.00 - x 5 100.00 $3,733.00 $4,583.50 - x 6 105.00 $3,455.00 $4,414.00 - x 8 116.00 $3,519.50 $4,696.50-12 x 12 14 x 14 16 x 16 18 x 18 20 x 20 24 x 24 LENGTH EAH (LBS) Steel ross Fig. 7068 (Fabricated) True Y Fig. 7071 (Fabricated) PAINTED GALV. x 4 116.00 $4,414.00 $5,862.00 - x 5 137.00 $4,083.50 $5,862.00 - x 6 140.00 $4,083.50 $5,820.50 - x 8 147.00 $4,135.50 $5,586.50 - x 10 168.00 $4,190.50 $5,769.00 - x 4 173.00 $2,958.50 $4,450.00 - x 6 185.00 $3,176.00 $4,748.00 - x 8 195.00 $3,416.50 $5,371.50 - x 10 223.00 $4,329.00 $5,673.00 - x 12 240.00 $4,394.00 $6,296.00 - x 6 235.00 $4,603.50 $6,549.00 - x 8 250.00 $4,867.00 $7,833.00 - x 10 263.00 $5,679.50 $7,750.50 - x 12 283.00 $5,920.00 $8,313.00 - x 14 307.00 $5,920.00 $8,313.00 - x 6 275.00 $5,920.00 $8,313.00 - x 8 306.00 $5,920.00 $8,313.00 - x 10 321.00 $8,354.00 $12,590.50 - x 12 333.00 $6,579.50 $9,300.00 - x 14 358.00 $7,875.00 $10,242.50 - x 16 382.00 $8,858.50 $11,442.50 - x 12 390.00 $8,466.00 $12,089.50 - x 14 410.00 $8,727.00 $12,459.00 - x 16 440.00 $10,294.00 $14,308.50 - x 16 725.00 $19,539.50 $25,160.50 - x 20 785.00 $21,255.50 $25,992.00 - Grooved-End ouplings Fittings opper Method Plain-End Spare Parts Valves and Accessories Tools 25

STANDARD PRODUTS Price List Grooved-End ouplings High Pressure Fittings 90 LR Elbow Fig. 7050EG 45 LR Elbow Fig. 7051EG Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories Tee Fig. 7060EG EAH (LBS) PAINTED 2 2.50 $454.50-2 ½ 4.20 $629.00-3 6.00 $454.50-4 11.00 $636.00-6 27.20 $2,326.00 - *8 - POA - *10 - POA - *12 - POA - *ontact your Anvil Representative for pricing. EAH (LBS) PAINTED 2 3.30 $756.00-2 ½ 5.10 $953.00-3 9.30 $1,024.00-4 15.90 $1,169.00-6 38.50 $2,461.00 - *8 0.01 POA - *10 0.01 POA - *12 0.01 POA - ENTER TO END APPROX. EAH (LBS) PRIE EAH QTY. 2 6.5 4.90 $886.00-2 5.0 3.60 $849.50 - *ontact your Anvil Representative for pricing. Header Tee Fig. 7662EG *ontact your Anvil Representative for pricing. ross Fig. 7068EG EAH (LBS) PAINTED 2 1.80 $593.00-2 ½ 2.90 $593.00-3 4.30 $593.00-4 7.50 $786.50-6 16.50 $1,265.50 - *8 - POA - *10 - POA - *12 - POA - EAH (LBS) ontact your Anvil Representative for pricing. PAINTED 2 3.90 POA - 2 ½ 6.80 POA - 3 11.50 POA - 4 19.30 POA - 6 46.00 POA - 8 - POA - 10 - POA - 12 - POA - 26

STANDARD PRODUTS Price List Valve with Nylon oated Body (Grade E or Grade T Disc) Sample Part Number 8" AN7721-3 Valves for Grooved-End Pipe Grooved End Butterfly Valve Series 7700 SIZE (AN7721-3-"E") (AN7711-3-"T") 10 POSITION HANDLE WITH LATH-LOK MEMORY STOP BOX QTY. (AN7722-3-"E") (AN7712-3-"T") GEAR OPERATOR BOX QTY. GEAR OPERATOR WITH HAINWHEEL 2 $852.50 98 $1,556.00 32 + 2 ½ $1,049.50 98 $1,752.00 32 + 3 $1,094.50 98 $1,797.50 32 + 4 $1,307.50 98 $2,011.50 32 + 5 $2,328.00 48 $3,031.50 24 + 6 $2,459.00. 48 $3,132.00 24 + 8 $3,197.50 8 $3,871.00 8 + 10 - - $5,134.50 6 + 12 - - $5,692.00 4 + + Priced on Application. ontact your Anvil Representative for Engineering Assistance. GRUVLOK BUTTERFLY VALVE SERIES 7700 (ORDERING INFORMATION) 8" A N 77 2 1-3 Special Size Body Style Body oating Series Disc oating Operator Stem 2" 12" A N Nylon 77-77XX 1 Nitrile (Grade 0 None 3 416 S.S. SF Silicone Free T) 1 10 Pos. L / Lock 2 EPDM (Grade E) 2 Gear Operator D Infinite Pos. w / Memory Stop 4 Short 10 Pos. L / Lock Operator Gruvlok Butterfly Valve Fig. 8000GR SIZE: 14" 24" SERIES 8000GR BUTTERFLY VALVES (Ordering Information) 18" G - 8 2 8 2-6 Grooved-End ouplings Fittings opper Method Plain-End Spare Parts Valves and Accessories Valve Size 14" 24" Body Style G -Grooved-End Body Material - ast iron Series 8-8000 Seat Material 1 - Nitrile 2 - EPDM Disc Material 0 - Nickel-Plated ductile iron 7-316 S.S. 8 - Bronze (Al-Brz) *ontact your Anvil Representative for Engineering Assistance Operator 0 - None 2 - Gear Operator 3 - Pneumatic 4 - Electric 5 - Spring Return Pneumatic 6 - Square Nut (with Gear Operator) 7 - hain Wheel (with Gear) Stem 6-416 S.S. with RTFE Bearing 7-316 S.S. with RTFE Bearing (LBS.) SIZE VALVE ONLY W/ GEAR OPERATOR WITH GEAR OPERATOR 14 354.00 378.00 $7,841.50-16 428.00 452.00 $10,726.50-18 524.00 548.00 $13,201.50-20 704.00 728.00 $17,863.00-24 1,097.00 1,097.00 $22,745.50 Tools 27

STANDARD PRODUTS Price List Grooved-End ouplings Valves and Accessories Grooved End Butterfly Valve, Series 7600 Grooved End Butterfly Valve, Fig. 70G Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories PIPE SIZE TWO POSITION DETENT HANDLE EAH (LBS.) 2 3.30 $826.00 1 2 ½ 6.40 $1,046.00 1 3 6.80 $1,183.50 1 4 7.50 $1,301.50 1 5 26.10 $2,483.50 1 6 17.10 $2,625.50 1 Gruvlok Ball Valves Fig. 7500 DI Body with 304 Stainless Steel Trim (Example: 7542-2) Sample Part Number 4" GI-7512-2 > SERIES 7500 BALL VALVES (ORDERING INFORMATION) 4" G I - 75 4 2-2 Size onfiguration Body/End Material 2" - 6" G - 2 Way Grooved End Fig. 7500 Sizes 2" - 4" SIZE EAH (LBS.) WITH TWO POSITION LOKING HANDLE 2 7.72 $527.00-3 18.38 $1,853.50-4 33.20 $2,867.00 - I - Ductile Iron ASTM A395 DI Body with 316 Stainless Steel Disc DI Body with 316 Stainless Steel Trim (Example: 7562-2) Note: Stainless Steel available. See Stainless Steel Price Sheet for listing price. Series "E" OR "T" SEAL SIZE EAH (LBS.) 2 3.85 $948.00 3 7.57 $1,272.00 4 12.25 $1,381.00 6 31.61 $2,577.00 SIZE EAH (LBS.) WITH TWO POSITION LOKING HANDLE 2 7.72 $812.00-3 18.38 $2,637.00-4 33.20 $3,589.50-6 83.80 $7,697.00 $7,762.00 Ball and Stem Material 75-7500 4-304 Stainless Steel (2" - 4") 6-316 Stainless Steel Seat Material 2 - RTFE / Flouroelastomer WITH MINING HANDLE (7562-M) Operator 2-2 Position Locking Handle 3 - Bare Stem (6" only) M - Mining Handle 28

STANDARD PRODUTS Price List Gruvlok ircuit Balancing Valves Grooved End Straight GBV-G, End Angle Fig. GBV-A, & Flanged Fig. GBV-F Grooved heck Valve, Fig. 90G Grooved-End ouplings ITEM EAH (LBS.) GBV-G GBV-A GBV-F 2 ½ 25.00 $901.00 $917.50 $1,042.00 3 28.00 $1,401.00 $1,427.50 $1,592.00 4 41.00 $1,936.50 $1,973.00 $2,193.50 5 90.00 $3,503.00 $3,569.50 $3,924.50 6 130.00 $4,692.50 $4,781.50 $5,015.50 8 310.00 $9,996.50 $10,187.00 $10,839.50 10 460.00 $13,115.50 $13,365.50-12 870.00 $28,500.50 $29,043.50 - Silent heck Valve, Fig. 400G Gruvlok End heck Valve, Fig. 7800 EAH (LBS.) LIST PRIE 2 12.00 $1,524.50-2 ½ 15.00 $1,853.50-3 20.00 $2,085.00-4 36.00 $2,759.00-5 50.00 $3,819.50-6 68.00 $4,609.50-8 140.00 $7,868.00-10 198.00 $11,954.00 "E" OR "T" SEAL SIZE EAH (LBS.) 2 11.35 $577.50 2 ½ 21.25 $950.00 3 15.95 $1,104.00 4 33.17 $1,569.00 EAH (LBS.) EPDM LIST PRIE BUNA LIST PRIE 2 7.50 $762.50 $762.50 2 ½ 10.50 $795.00-3 11.50 $939.00 $939.00 4 13.50 $991.50 $991.50 5 19.00 $1,646.00-6 33.50 $1,952.00 $1,952.00 8 59.00 $2,666.00 $2,666.00 10 130.00 $7,133.50-12 183.00 $8,452.50 - The series 7800 Gruvlok heck Valve comes standard with cast ductile iron body, stainlees steel seat ring, hinge pin and closure spring. lapper seat facing of grade E EPDM or grade T (buna) Elastomer. NPT plugs in the body accomodate valve drain-down. Tools opper Method Plain-End Spare Parts Valves and Fittings Accessories 29

STANDARD PRODUTS Price List Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories Suction Diffuser Fig. 7250 GROOVED END INLET X FLANGE LENGTH ADAPTER OUT- LET EAH (LBS) PAINTED 2 ½ x 2½ 2½ x 2½ 36.00 $4,611.50 - BOX QTY. x 2 3 x 2 36.00 $3,843.00-3 x 2½ 3 x 2½ 36.00 $2,763.50 - x 3 3 x 3 37.00 $2,800.00 - x 2 4 x 2 38.00 $3,511.00-4 x 2½ 4 x 2½ 38.00 $3,035.00 - x 3 4 x 3 38.00 $3,274.00 - x 4 4 x 4 72.00 $3,792.50-5 x 4 5 x 4 74.00 $4,227.00 - x 5 5 x 5 75.00 $4,439.50 - x 3 6 x 3 72.00 $5,449.00-6 x 4 6 x 4 72.00 $4,506.50 - x 5 6 x 5 74.00 $5,388.50 - x 6 6 x 6 133.00 $5,595.50 - x 5 8 x 5 118.00 $5,739.50-8 x 6 8 x 6 118.00 $6,052.00 - x 8 8 x 8 190.00 $10,412.50 - x 6 10 x 6 100.00 $10,810.00-10 x 8 10 x 8 203.00 $11,747.50 - x 10 10 x 10 192.00 $14,154.00 - x 8 12 x 8 196.00 $14,821.00-12 x 10 12 x 10 196.00 $16,754.50 - x 12 12 x 12 382.00 $23,301.00 - x 10 14 x 10 382.00 $19,411.50-14 x 12 14 x 12 382.00 $21,684.00 - x 14 14 x 14 467.00 $21,683.50-16 x 14 16 x 14 467.00 $27,101.00 - All fabricated steel. The Fig. 7250 Gruvlok Suction Diffuser comes standard with type 304 stainless steel diffuser and pre-filter screen, ductile or malleable iron access cap and coupling with Grade E EPDM gasket, and plated bolts and nuts. NPT taps and plugs are provided in the body to accommodate drain and gauges. Groove x Groove onnectors lass 150 (AF-21-GG) ANVILFLEX AF-21-GG ANVIL SF-21-GG END TO END END TO END 2 12 12 $487.50-2 ½ 12 14 $590.00-3 12 14 $673.50-4 14 16 $866.00-5 16 17 $1,353.00-6 16 18 $1,494.50-8 16 20 $2,855.50-10 20 24 $4,934.50-2½ - 12" have different end to end dimensions. 12 20 25 $6,965.00 - Groove x Flange onnectors lass 150 (AF-21-GF) ANVILFLEX AF-21-GF ANVIL SF-21-GF END TO END END TO END 2 12 12 $519.00-2 ½ 12 12 $645.50-3 12 13 $769.50-4 12 13 $899.50-5 14 14 $1,429.00-6 14 14 $1,540.50-8 15 15 $2,812.50-10 16 16 $4,979.00-12 17 17 $6,997.00-3" & 4" have different end to end dimensions. Flange x Flange onnectors lass 150 (AF-21-FF) ANVILFLEX AF-21-FF ANVIL SF-21-FF END TO END END TO END 2 9 9 $537.50-2 ½ 9 9 $658.50-3 9 9 $759.00-4 9 9 $923.00-5 11 11 $1,415.00-6 11 11 $1,613.00-8 12 12 $3,378.00-10 13 13 $4,960.00-12 14 14 $7,118.50 - Reducing and combination flex connectors available. ontact your Anvil Representative. 30

STANDARD PRODUTS Price List Gruvlok Air Vent GAV-15 & GAV-30 Grooved-End Strainer Fig. 7260 Grooved-End ouplings SIZE GAV-15 EAH (LBS.) GAV-30 PART NUMBER INLET SIZE PAINTED ½ GAV-15 5.50 ½ $637.00 - ¾ GAV-15 5.50 ¾ $637.00-1 GAV-15 5.50 1 $637.00 - ½ GAV-30 8.00 ½ $965.50 - ¾ GAV-30 8.00 ¾ $965.50 - Fig. 758G Grooved-End WYE Strainer APPROX. EAH (LBS) LIST PRIES PAINTED GALV. 2 12.00 $1,987.00 $2,220.50-2 ½ 18.00 $2,086.00 $2,364.50-3 23.00 $2,343.50 $2,694.00-4 42.00 $2,652.50 $3,136.00-5 80.00 $3,839.50 $4,575.00-6 112.00 $4,167.50 $5,128.00-8 205.00 $6,387.00 $7,995.50-10 277.00 $10,265.50 $12,888.50-12 470.00 $17,931.50 $21,792.00 - Grooved-End WYE Strainer Fig. 768G EAH (LBS.) QTY. PAINTED 2 10.00 $1,892.00-2 ½ 13.99 $1,987.50-3 20.73 $2,231.50-4 33.46 $2,526.00-5 46.00 POA - 6 72.40 $3,967.00-8 162.15 $6,080.00-10 238.71 $9,770.50-12 360.58 $17,062.50 - PIPE SIZE EAH (LBS.) The Fig. 7260 Gruvlok Strainer comes standard with type 304 stainless steel strainer screen, ductile iron access cap and coupling with Grade E EPDM gasket, and plated bolts and nuts. An NPT tap and plugs are provided in the access cap to accommodate a drain or blow-down valve. Additional sizes available, contact your Anvil Representative for engineering assistance. Gruvlok Tri-Service Valve Fig. FTV-S (Straight) or Fig. FTV-A (Angle Body) FTV-S (Straight) PAINTED GALV. 2 6.00 $1,868.50 $2,191.00-2 ½ 8.00 $1,963.50 $2,313.50-3 13.00 $2,203.50 $2,638.00-4 22.28 $2,493.50 $3,055.00-5 30.00 $3,611.00 $4,323.50-6 44.82 $3,917.50 $4,776.50-8 99.00 $6,004.50 $7,383.00-10 136.00 $8,814.00 $10,881.00-12 191.00 $11,347.00 $13,972.50-14 300.00 $35,531.50 POA - 16 350.00 $44,161.00 POA - 18 400.00 $58,081.00 POA - FTV-A (Angle) EAH (LBS.) 2 ½ 24.00 $4,544.00-3 28.00 $4,943.50-4 41.00 $6,775.00-5 81.00 $7,415.00-6 156.00 $11,099.50-8 300.00 $16,477.00-10 392.00 $27,214.00-12 496.00 $38,191.50 Tools opper Method Plain-End Spare Parts Valves and Fittings Accessories 31

Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories 32 lamp-t Outlets Mechanical Tee Product Fig. 7045 lamp-t Female Threaded Outlet PIPE SIZE RUN 2 2 ½ 3 4 5 6 OUTLET EAH (LBS.) lamp T s are available with grooved or female threaded outlet with Grade E or Grade T gasket. Weights are approximate and subject to change. * All bolts and nuts are of track head design and are zinc plated conforming to physical properties of ASTM B-633. ** lamp-t supplied with U-Bolt lower housing. *** Note: 8 x 2 is actually 8 x 2 1/2 bushed down. STANDARD PRODUTS Price List Fig. 7045 (U-Bolt) OMPLETE LAMP-T FEMALE THREADED OUTLET E OR T GASKET *BOLT AND BOX NUT SIZE PAINTED QTY. GALV. QTY. x ½** 2.30 $98.50 - $124.50 - ½ U-Bolt x ¾** 2.20 $98.50 - $124.50 - ½ U-Bolt x 1** 2.07 $98.50 - $124.50 - ½ U-Bolt x 1¼** 2.80 $114.00 - $141.00 - ½ U-Bolt x 1½** 2.56 $114.00 - $142.00 - ½ U-Bolt x ½** 2.60 $98.50 - $124.50 - ½ U-Bolt x ¾** 2.50 $98.50 - $124.50 - ½ U-Bolt x 1** 1.81 $98.50 - $124.50 - ½ U-Bolt x 1¼** 2.32 $138.50 - $169.00 - ½ U-Bolt x 1½** 2.14 $138.50 - $169.00 - ½ U-Bolt x ½** 2.79 $114.00 - $138.50 - ½ U-Bolt x ¾** 2.75 $114.00 - $138.50 - ½ U-Bolt x 1** 2.51 $114.00 - $138.50 - ½ U-Bolt x 1¼ 4.04 $144.00 - $180.00 - ½ U-Bolt x 1½ 3.75 $144.00 - $180.00 - ½ U-Bolt x 2 4.04 $165.50 - $205.50 - ½ U-Bolt x ½** 3.21 $143.50 - $170.50 - ½ U-Bolt x ¾** 3.17 $143.50 - $170.50 - ½ U-Bolt x 1** 3.03 $143.50 - $170.50 - ½ U-Bolt x 1¼ 4.44 $168.00 - $197.50 - ½ U-Bolt x 1½ 4.40 $174.00 - $219.50 - ½ U-Bolt x 2 4.67 $174.00 - $221.00 - ½ U-Bolt x 2½ 5.15 $181.50 - $235.00 - ½ U-Bolt x 3 7.09 $193.50 - $248.00 - ½ U-Bolt x 1¼ 6.34 $164.00 - $267.00 - ½ U-Bolt x 1½ 6.20 $212.50 - $269.50 - ½ U-Bolt x 2 6.61 $212.50 - $269.50 - ½ U-Bolt x 2½ 7.24 $224.00 - $285.50 - ½ U-Bolt x 3 8.50 $238.50 - $306.00 - ½ U-Bolt x 1¼ 7.04 $182.00 - $277.50 - ½ U-Bolt x 1½ 6.86 $218.00 - $278.50 - ½ U-Bolt x 2 7.31 $218.50 - $278.50 - ½ U-Bolt x 2½ 7.80 $234.50 - $303.00 - ½ U-Bolt x 3 9.60 $248.50 -- $320.50 - ½ U-Bolt x 4 12.98 $276.00 - $359.00 - ½ U-Bolt PIPE SIZE RUN 8 OUTLET Mechanical Tee Product Fig. 7046 lamp-t Grooved Outlet PIPE SIZE RUN 2 ½** 3 4 5 6 8 EAH (LBS.) OMPLETE LAMP-T FEMALE THREADED OUTLET E OR T GASKET BOX PAINTED QTY. GALV. QTY. lamp T s are available with grooved Grade E or Grade T gasket. Weights are approximate and subject to change. *All bolts and nuts are of track head design and are zinc plated conforming to physical properties of ASTM B-633. ** lamp-t supplied with U-Bolt lower housing. *BOLT AND NUT SIZE x 2*** 11.36 $379.50 - $478.50 - ½ U-Bolt x 2½ 11.13 $379.50 - $478.50 - ½ U-Bolt x 3 12.40 $400.50 - $508.00 - ½ U-Bolt x 4 16.00 $412.50 - $532.50 - ½ U-Bolt OUTLET EAH (LBS.) OMPLETE LAMP-T GROOVED BRANH* E OR T GASKET BOX PAINTED QTY. GALV. QTY. *BOLT AND NUT SIZE x 1¼ 2.50 $138.50 - $169.00 - ½ U-Bolt x 1½ 2.09 $138.50 - $169.00 - ½ U-Bolt x 1¼ 3.80 $144.00 - $180.00 - ½ x 2¾ x 1½ 3.90 $144.00 - $180.00 - ½ x 2¾ x 2 4.12 $165.50 - $205.50 - ½ x 2¾ x 1¼ 4.41 $168.00 - $197.50 - ½ x 2¾ x 1½ 4.23 $174.00 - $219.50 - ½ x 2¾ x 2 4.60 $174.00 - $221.00 - ½ x 2¾ x 2½ 4.68 $181.50 - $235.00 - ½ x 2¾ x 3 6.75 $193.50 - $248.00 - ½ x 3½ x 1¼ 5.70 $192.50 - $267.50-5 ₈ x 3¼ x 1½ 5.30 $212.50 - $278.50-5 ₈ x 3¼ x 2 6.40 $212.50 - $269.50-5 ₈ x 3¼ x 2½ 6.80 $224.00 - $296.00-5 ₈ x 3¼ x 3 8.40 $238.50 - $306.00-5 ₈ x 3¼ x 1¼ 7.66 $218.50 - $278.50-5 ₈ x 4¼ x 1½ 7.17 $218.50 - $278.50-5 ₈ x 4¼ x 2 7.13 $218.50 - $278.50-5 ₈ x 4¼ x 2½ 7.85 $238.50 - $303.00-5 ₈ x 4¼ x 3 8.37 $248.50 - $320.50-5 ₈ x 4¼ x 4 10.11 $276.00 - $359.00-5 ₈ x 4¼ x 2 11.00 $379.50 - $499.00 - ¾ x 4¼ x 2½ 10.58 $379.50 - $478.50 - ¾ x 4½ x 3 12.20 $400.50 - $508.00 - ¾ x 4½ x 4 13.20 $412.50 - $532.50 - ¾ x 4½

STANDARD PRODUTS Price List Mechanical Tee Product lamp-t ross Fig. 7047, Fig. 7048 and Fig. 7049 Grooved-End ouplings Fig. 7047 Thread x Thread Fig. 7048 Groove x Groove Fig. 7049 Groove x Thread Fittings RUN A 2 ½ 3 44 OUTLET B OMPLETE LAMP-T ROSS WITH E OR T GASKET PAINTED GALV. 1 x 1* $156.00 $199.00-1 x 1¼* $213.00 $275.50-1 x 1½* $213.00 $275.50-1¼ x 1¼* $213.00 $275.50-1½ x 1¼* $213.00 $275.50-1½ x 1½* $213.00 $228.00-1 x 1* $174.00 $224.00-1 x 1¼ $213.00 $213.00-1 x 1½ $213.00 $265.50-1 x 2 $246.00 $304.50-1¼ x 1 $196.00 $244.00-1¼ x 1¼ $213.00 $265.50-1½ x 1¼ $213.00 $265.50-1½ x 1½ $213.00 $265.50-2 x 1¼ $213.00 $304.50-2 x 1½ $246.00 $304.50-2 x 2 $246.00 $304.50-1 x 1 $246.00 $276.50-1 x 1¼ $213.00 $326.50-1 x 1½ $259.00 $324.50-1 x 2 $276.50 $326.50-1¼ x 1 $238.50 $300.50-1¼ x 1¼ $276.50 $324.50-1½ x 1¼ $259.00 $324.50-1½ x 1½ $259.00 $324.50-2 x 1¼ $259.00 $326.50-2 x 1½ $259.00 $326.50-2 x 2 $276.50 $327.50-2½ x 2½ $276.50 $352.00-3 x 1½ $265.50 $343.00-3 x 3 $276.50 $372.50 - RUN A 5 6 8 OUTLET B OMPLETE LAMP-T ROSS WITH "E" OR "T" GASKET PAINTED GALV. 1½ x 1½ $316.00 $400.50-2 x 1½ $333.00 $400.50-2 x 2 $316.00 $400.50-2½ x 1½ $333.00 $424.50-2½ x 2 $333.00 $457.00-2½ x 2½ $333.00 $424.50-3 x 1½ $356.00 $457.00-3 x 2 $356.00 $457.00-3 x 2½ $356.00 $457.00-3 x 3 $356.00 $457.00-1½ x 1½ $323.50 $416.50-2 x 1½ $323.50 $416.50-2 x 2 $337.00 $449.50-2½ x 2½ $347.00 $449.50-3 x 2½ $371.50 $476.00-3 x 3 $371.50 $476.00-4 x 2½ $410.50 $532.50-4 x 3 $410.50 $532.50-4 x 4 $410.50 $532.50-2½ x 2½ $567.50 $716.00 - *Avaiable with Female Threaded outlet only. Always specify gasket grade when ordering. 3 x 2½ $597.00 $758.50-3 x 3 $597.00 $758.50-4 x 2½ $617.50 $797.50-4 x 3 $617.50 $797.50-4 x 4 $617.50 $797.50 Tools opper Method Plain-End Spare Parts Valves and Accessories 33

Grooved-End ouplings Adapter Flanges Flange Nipples, Fig. 7084 (150 lb) & Fig. 7085 (300 lb) STANDARD PRODUTS Price List Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories SIZE Flange by concentric reducer configurations also available. ontact your Anvil Representative for more dimensions and weights or additional details. Spare Parts Flange Parts for Gruvlok Flange Fig. 7012 FLANGE SIZE Note: items listed are non-cancellable and non-returnable 34 FIG. 7084 (150 LB) (Fabricated) FIG. 7085 (300 LB) END TO END PAINTED GALV. PAINTED GALV. 1 x 3 $457.50 $721.00 POA POA - 1 ¼ x 4 $457.50 $721.00 POA POA - 1 ½ x 4 $441.50 $693.50 $507.00 POA - 2 x 4 $441.50 $693.50 $540.50 $635.50-2 ½ x 4 $879.00 $1,035.50 $540.50 $635.50-3 x 4 $900.50 $1,069.50 $750.00 $948.50-3 ½ x 4 $1,068.00 $1,554.50 POA POA - 4 x 6 $1,025.50 $1,495.00 $1,411.50 $1,613.50-5 x 6 $1,420.00 $1,964.00 $1,444.50 POA - 6 x 6 $1,445.00 $1,993.50 $1,444.50 $2,180.00-8 x 6 $1,788.50 $2,660.50 $2,953.00 $3,511.50-10 x 8 $2,700.50 $4,047.00 $3,659.50 $4,658.50-12 x 8 $3,696.00 $5,335.50 $5,492.50 $10,041.00-14 x 8 $6,324.00 $7,034.00 POA POA - 16 x 8 $7,535.50 $8,747.50 POA POA - 18 x 8 $8,341.50 $9,081.00 POA POA - 20 x 8 $8,751.00 $9,468.00 POA POA - 24 x 8 $9,161.50 $9,857.00 POA POA - QTY. PER SET MATING FLANGE BOLT AND NUT SIZE PRIE PER SET PLATED SEAL RING FIG. 7012 2 4 5/8 x 2¾ $87.50 $123.00 4 2 ½ 4 5/8 x 2¾ $87.50 $130.00 4 3 4 5/8 x 2¾ $87.50 $151.50 4 4 8 5/8 x 2¾ $172.00 $176.00 8 5 8 ¾ x 27/8 $186.50 $212.50 8 6 8 ¾ x 31/8 $186.50 $242.50 8 8 8 ¾ x 3¼ $186.50 $306.00 8 10 12 7/8 x 3½ $417.00 $424.00 12 12 12 7/8 x 3¾ $417.00 $618.00 12 14 12 1 x 4¼ $693.00 $674.00 12 16 16 1 x 4¼ $924.50 $1,196.50 16 18 16 11/8 x 4¾ $1,388.00 $1,275.00 16 20 20 11/8 x 4¾ $1,776.00 $1,260.50 20 24 20 1¼ x 5½ $2,210.50 $2,114.50 20 Flange Parts for Gruvlok Flange Fig. 7013 FLANGE SIZE QTY. PER SET MATING FLANGE BOLT AND NUT SIZE PRIE PER SET PLATED SEAL RING FIG. 7013 2 8 5/8 x 3 $87.50 $123.00 8 2 ½ 8 ¾ x 3¼ $87.50 $130.00 8 3 8 ¾ x 3½ $87.50 $151.50 8 4 8 ¾ x 3¾ $172.00 $176.00 8 5 8 ¾ x 4½ $186.50 $212.50 8 6 12 ¾ x 4½ $186.50 $242.50 12 8 12 7/8 x 4¾ $186.50 $306.00 12 10 16 1 x 5 $417.00 $424.00 16 12 16 11/8 x 5¾ $417.00 $618.00 16

STANDARD PRODUTS Price List Flange Gaskets for Fig. 7012 & 7013 Gruvlok Flanges FLANGE SIZE STANDARD GASKETS GRADE "E" OR "T" GASKET ONLY 2 $39.50-2 ½ $46.00-3 $49.50-4 $64.50-5 $77.50-6 $86.50-8 $116.00-10 $146.50-12 $170.50-14 $210.00-16 $232.50-18 $339.00-20 $366.50-24 $406.00 - Note: items listed are non-cancellable and non-returnable. Plated Trackhead Bolts and Nuts for ouplings BOLT AND NUT SIZE 3/8 x 2¼ $27.00-3/8 x 2½ $27.00 - ½ x 2¾ $23.50 - ½ x 3 $23.50 - ½ x 3½ $29.00-5/8 x 2¾ $27.50-5/8 x 3¼ $27.50-5/8 x 3½ $29.50-5/8 x 4¼ $33.00 - ¾ x 4½ $27.50-7/8 x 5 $55.50-7/8 x 5½ $64.50-7/8 x 6 $64.50-1 x 5½ $69.50-1 x 6 $69.50-1 x 6½ $73.50-11/8 x 5½ $94.50 - Note: items listed are non-cancellable and non-returnable. Standard Gaskets for Fig. 7005 & 7305 ouplings SIZE SIZE SIZE STANDARD GASKETS GRADE "E" OR "T" GASKET ONLY EG GASKET GASKET ONLY GRADE "E" EPDM OR GRADE "T" NITRILE 2 $82.00-2 ½ $103.00-3 $111.50-4 $143.50-6 $203.00-8 $273.50-10 $444.00-12 $507.00-2 $60.00-2 ½ $63.50-3 $69.50-4 $100.50-5 $118.50-6 $144.00-8 $187.50-10 $239.50-12 $291.50 - Fig. 7004EG Gasket (Use with 7004EG Housing) Note: items listed are non-cancellable and non-returnable. Standard Gaskets FLH GAP GRADE "E" Reducing oupling Fig. 7010 Loose Gasket PIPE SIZE SPARE PARTS "E" OR "T" GASKET ONLY 2 x 1½ $41.50-2½ x 2 $53.50-3 x 2 $61.00-3 x 2½ $61.00-4 x 2 $71.00-4 x 2½ $71.50-4 x 3 $73.50-5 x 4 $85.50-6 x 4 $97.50-6 x 5 $106.50-8 x 6 $118.00 - GRADE "L" SILIONE GRADE "O" FLUOROELASTOMER 1 $43.00 $80.00 $149.50 $496.00 1 ¼ $45.50 $85.00 $214.00 $476.00 1 ½ $48.00 $86.50 $223.00 $502.00 2 $48.00 $87.50 $138.50 $410.50 2 ½ $56.50 $107.00 $161.00 $464.50 3 $60.50 $107.00 $173.00 $512.50 4 $76.50 $143.50 $251.00 $839.50 5 $97.50 $232.00 $492.50 $899.50 6 $105.50 $258.50 $538.50 $1,101.50 8 $143.50 $267.00 $602.00 $1,261.50 10 $179.50 $317.00 $782.50 $1,643.00 12 $209.00 $376.50 $923.00 $2,431.00 14 $286.00 $424.00 - - 16 $393.50 POA - - 18 $472.50 POA - - 20 $727.50 POA - - 24 $1,006.00 POA - - Grooved-End ouplings Fittings opper Method Plain-End Spare Parts Valves and Accessories Tools 35

STANDARD PRODUTS Price List Grooved-End ouplings Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories Fig. 7045 lamp-t Female Threaded Outlets (Gasket Only) Fig. 7046 lamp-t Grooved Outlets (Gasket Only) Gaskets Only RUN Roughneck Plain-End Products Plain-End oupling Roughneck oupling Fig. 7005 PIPE OUTSIDE DIAMETER OUTLET "E" OR "T" GASKET (GASKET ONLY) 2 2½ x ½ 1 $24.00 2 2½ x 1¼ 1½ $24.00 3 4 x ½ 1½ $24.00 3 8 x 2 $24.00 4 5 x 2½ $27.50 4 8 x 3 $30.00 5 6 x 1¼ 1½ $24.00 6 8 x 2½ $29.00 6 8 x 4 $40.00 EAH (LBS.) OUPLING OMPLETE W/ E OR T GASKET PAINTED GALV. PLATED BOLT AND NUT SIZE 2 2.375 6.58 $222.00 $286.50-5/8 x 3¼ 2 ½ 2.875 7.35 $222.00 $286.50-5/8 x 3¼ 3 3.500 10.56 $324.50 $424.00 - ¾ x 4½ 4 4.500 13.97 $374.50 $496.50 - ¾ x 4½ 5 5.563 23.75 $532.50 $707.00-7/8 x 5 6 6.625 28.00 $649.50 $880.50-1 x 6 8 8.625 36.80 $1,144.50 $1,530.50-7/8 x 5 10 10.750 40.00 $1,485.50 $1,994.50-1 x 6½ 12 12.750 56.00 $1,864.50 $2,570.50-1 x 6½ 14 14.000 88.00 $2,559.00 $3,061.00-1 x 6½ 16 16.000 95.00 $3,501.00 $4,117.50-1 x 6½ All bolts are oval-neck track head design to ASTM A-183, with heavy hex nuts to ASTM A-563, and are zinc plated to ASTM B-633. Weights are approximate and subject to change. Plain End Fittings are manufactured from fabricated steel. Other sizes available. Priced on application. 36

STANDARD PRODUTS Price List DI-LOK DI-Electric Nipple Fig. 7088 (Gr. x Th.) DI-LOK DI-Electric Nipple Fig. 7089 (Gr. x Gr.) Grooved-End ouplings STEEL TUBE LENGTH DI-LOK DI-Electric Nipple Fig. 7090 (Th. x Th.) Insulator EAH (LBS.) PRIE EAH 1 4 0.46 $94.00 25 1 ¼ 4 0.74 $124.50 10 1 ½ 4 0.80 $145.50 10 2 4 1.46 $148.00 10 2 ½ 6 3.10 $200.00 6 3 6 4.46 $358.00 6 4 6 6.10 $478.00 6 LENGTH EAH (LBS.) PRIE EAH ½ 3 0.20 $52.00 25 ¾ 3 0.28 $52.00 25 1 4 0.65 $78.00 25 1 ¼ 4 0.80 $107.50 10 1 ½ 4 0.95 $130.00 10 2 4 1.14 $148.00 10 2 ½ 6 1.60 $200.00 6 3 6 2.00 $358.00 6 STEEL TUBE LENGTH DI-LOK DI-Electric Fittings Fig. 7091 (TS x IPS) Insulator EAH (LBS.) PRIE EAH 2 4 1.46 $149.50-2 ½ 6 3.10 $203.50-3 6 4.46 $368.00-4 6 6.10 $493.00 - LENGTH EAH (LBS.) PRIE EAH 2 4 1.32 $252.00 12 2 ½ 6 2.85 $281.50 6 3 6 4.27 $431.00 6 4 6 5.62 $864.50 4 6 6 9.66 $998.00 2 8 6 20.00 $1,693.00 1 opper Method Plain-End Spare Parts Valves and Fittings Accessories Tools 37

STANDARD PRODUTS Price List Grooved-End ouplings Red-White Valves Hydronic Hook-up Kits The following components are used in hydronic hook-up kits. Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories MBV-9510 MBV-9510 Series Fixed Orifice Static Balancing Valves MBV-9510AB ABV-9900 Series Automatic Balancing Valves Red-White Valve Hook-up Kits integrate the components required to connect piping to hydronic heating system or chiller system equipment. These kits are configured to the system designer's specifications. Hydronic Hook-up Kit - Accessories MBV-9510 Series Fixed Orifice Static Balancing Valves MBV-T-9517 MBV-T-9517AB MBV-S-9519 MBV-S-9519AB ABV-T-9907 ABV-S-9909 ½ $110.50 $152.00 $110.50 $152.00 $279.50 $279.50 ¾ $110.50 $161.50 $110.50 $161.50 $316.00 $316.00 1 $158.50 $176.50 $152.00 $176.50 $354.00 $354.00 1 ¼ $210.00 $235.50 $200.00 $235.50 $654.50 $654.50 1 ½ $245.50 $278.00 $236.00 $278.00 $746.00 $746.00 2 $314.50 $353.50 $299.00 $353.50 $1,753.00 $1,753.00 92ST 92BP 92UN ½ $65.00 $43.00 $33.50 ¾ $78.50 $51.00 $44.50 1 $94.00 $68.00 $49.50 1 ¼ $137.50 POA $60.50 1 ½ $174.00 POA $89.00 2 $258.50 POA $107.50 92HS 24" 36 ½ $53.50 $62.00 ¾ $93.50 $112.50 1 $162.50 $190.50 1 ¼ $252.00 $307.00 1 ½ $303.00 $333.00 2 $433.00 $470.50 92UMA MIRO UNION A $17.00 B $18.50 $34.50 D $40.00 E $66.00 F $87.00 MANOMETER POA 38

Roll Groovers STANDARD PRODUTS Price List Model 1007/3007 Roll Groover SHIPPING ITEM (LBS.) PRIE INLUDES 1007 Roll Groover 550.00 $22,305.00-3007 Roll Groover 330.00 $10,737.50 - Motorized Roll Groover with 2"-12" Steel Rolls losed Wood rate For Ridgid 300 Power Drive Support Legs 2"-12" Steel losed Wood rate Fig. 1007 Grooved-End ouplings Fittings Model 3006 (Steel Roll Groover) for Ridgid 300 Power Drive ITEM ontact your Anvil representative for roll groover parts and accessory pricing. SHIPPING (LBS.) PRIE INLUDES 3006 Roll Groover 170.00 $9,999.00-2"-12" Steel Rolls Hydraulic Pressure Gauge Support Legs losed Wood rate (1 set) Depth Gauges 1"-12" Fig. 3007 opper Method Plain-End Spare Parts Valves and Accessories Tools 39

Grooved-End ouplings STANDARD PRODUTS Price List Expansion Joints for Grooved-End Pipe Fig. 7240 Expansion Joints Fittings Valves and Spare Parts Plain-End opper Method Tools Accessories Pipe Size 2 2 1 /2 3 4 5 6 8 10 12 Nominal Pipe O.D. 2.375 2.875 3.500 4.500 5.562 6.625 8.625 10.750 12.750 oupling Figure 7000 7000 7000 7000 7000 7000 7000 7001 7001 PERFORMANE DATA (Inches) Y 5 1 /2 5 3 /4 6 3 /4 8 1 /8 9 5 /8 11 13 1 /4 17 1 /2 19 1 /2 ompressed Length L 30 30 30 17 1 /2 19 19 22 1 /2 23 1 /2 23 1 /2 Expanded Length L 31 1 /4 31 1 /4 31 1 /4 18 3 /4 20 1 /4 20 1 /4 23 3 /4 24 3 /4 24 3 /4 X 3 1 /2 4 4 5 /8 5 7 /8 7 8 10 3 /8 12 7 /8 15 oupling Movement apability 1 /8 1 /8 1 /8 1 /4 1 /4 1 /4 1 /4 1 /4 1 /4 Number of ouplings 10 10 10 5 5 5 5 5 5 Total Movement apability 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1 1 /4 1 1 /4 When requesting a quotation or placing an order, please complete the following form and fax a copy to 717-684-2131 to the attention of ustomer Service: 1) Size and material of pipe to which the expansion joint will be connected: 2) Factory to preset the Expansion Joint to: Full Expansion Full ontraction Intermediate 3) Total overall movement while in service: inches 4) Pipe material for Expansion Joint (standard is Sch. 40 steel): 5) Finish on pipe (standard is black): 6) Finish on couplings (standard is painted): 7) Gasket material (standard is Grade E EPDM): 8) onnecting pipe ends if different than standard roll or cut groove: 9) Are there any silicone restrictions for the application? Yes No 40

TS opper System STANDARD PRODUTS Price List Rigid oupling Fig. 6400 SlideLOK oupling Fig. 6402 *Gasket olor: opper PIPE OUTSIDE DIAMETER EAH (LBS.) OUPLING OMPLETE WITH E FLH GAP GASKET (PRIE EAH) PAINTED* PLATED BOLT AND NUT SIZE BOX QTY. 2 2.125 1.53 $69.00 42 ³ ₈ x 2¹ ₄ 2 ½ 2.625 1.78 $78.00 30 ³ ₈ x 2¹ ₄ 3 3.125 2.76 $87.50 20 ¹ ₂ x 3 4 4.125 3.27 $130.50 17 ¹ ₂ x 3 5 5.125 4.71 $219.00 10 ⁵ ₈ x 3¹ ₂ 6 6.125 5.24 $288.50 8 ⁵ ₈ x 3¹ ₂ 8 8.125 7.67 $446.50 5 ⁵ ₈ x 3¹ ₂ PIPE OUTSIDE DIAMETER EAH (LBS.) OUPLING OMPLETE WITH EP GASKET (PRIE EAH) PAINTED* PLATED BOLT AND NUT SIZE BOX QTY. 2 2.125 2.00 $73.00 15 ½ x 2¾ 2 ½ 2.625 2.00 $81.50 12 ½ x 2¾ 3 3.125 2.00 $91.50 12 ½ x 3½ 4 4.125 2.00 $137.50 10 ½ x 3½ 5 5.125 2.00 $230.50 8 ⁵ ₈ x 3½ 6 6.125 2.00 $303.50 6 ⁵ ₈ x 3½ 8 8.125 2.00 $470.00 1 ⁵ ₈ x 4¼ 90 Elbow Fig. 6050 (Gr x Gr) 45 Elbow Fig. 6051 (Gr x Gr) Tee Fig. 6060 (Gr x Gr x Gr) PIPE OUTSIDE DIAMETER EAH (LBS.) PRIE EAH 2 2.125 0.80 $131.00 35 2 ½ 2.625 1.26 $142.00 20 3 3.125 2.01 $199.00 12 4 4.125 4.07 $455.50 4 5 5.125 6.94 $1,289.00 2 6 6.125 11.12 $2,057.50 1 8 8.125 21.81 $3,862.50 1 BOX QTY. PIPE OUTSIDE DIAMETER EAH (LBS.) PRIE EAH 2 2.125 0.61 $131.00 44 2 ½ 2.625 1.00 $142.00 25 3 3.125 1.46 $199.00 15 4 4.125 2.99 $455.50 5 5 5.125 4.00 $1,289.00 4 6 6.125 6.16 $2,057.50 2 8 8.125 13.66 $3,862.50 2 BOX QTY. PIPE OUTSIDE DIAMETER EAH (LBS.) PRIE EAH 2 2.125 1.45 $214.50 25 2 ½ 2.625 2.37 $228.00 14 3 3.125 3.38 $339.00 8 4 4.125 5.77 $742.50 4 5 5.125 12.84 $2,075.50 2 6 6.125 21.00 $2,564.50 1 8 8.125 41.66 $4,579.50 1 BOX QTY. ertified to ANSI/NSF 61 ontact an ANVIL representative for details related to these listings. 41

STANDARD PRODUTS Price List opper Reducing Tee Fig. 6061 (Gr x Gr x Gr) opper Reducing Tee Fig. 6064 (Gr x Gr x up) EAH (LBS.) BOX QTY. 2 ½ x 2 ½ x 2 2.54 $339.50 14 3 x 3 x 2 3.06 $437.00 12 x 2 ½ 3.16 $576.00 10 4 x 4 5 x 5 6 x 6 x2 5.36 $975.00 5 x 2 ½ 5.88 $975.00 5 x3 10.06 $975.00 5 x3 10.86 $2,975.00 3 x4 9.42 $2,975.00 2 x 2 ½ 5.14 $3,631.50 2 x3 7.45 $3,631.50 2 x4 9.44 $3,631.50 2 x5 12.73 $3,631.50 2 2 x 2 2 ½x 2 ½ 3 x 3 4 x 4 EAH (LBS.) PRIE EAH x ¾ 0.97 $274.00 35 x1 1.03 $274.00 35 x 1 ¼ 1.12 $274.00 25 x 1 ½ 1.25 $274.00 25 x ¾ 1.25 $348.50 20 x1 1.38 $340.50 15 x 1 ¼ 1.56 $340.50 15 x 1 ½ 1.88 $340.50 15 x ¾ 2.08 $629.50 20 x 1 2.04 $629.50 16 x 1 ¼ 2.13 $629.50 15 x 1 ½ 2.48 $629.50 12 x ¾ 3.63 $744.00 8 x 1 3.94 $975.00 8 x 1 ¼ 4.24 $975.00 6 x 1 ½ 4.47 $975.00 6 oncentric Reducer Fig. 6072 (Gr x Gr) oncentric Reducer Fig. 6075 (Gr x up) SIZE X BRANH OUTLET END TO END EAH PRIE BOX (LBS.) EAH QTY. 2 ½ x 2 3.29 0.58 $188.00 60 3 x 2 2.5 0.58 $188.00 77 x 2 ½ 2.5 0.62 $188.00 72 x 2 4.75 1.71 $384.00 18 4 x 2 ½ 3 1.12 $384.00 30 x 3 3 1.22 $384.00 30 5 x 3 3.88 2.11 $1,078.00 12 x 4 3.88 1.97 $1,078.00 12 x 3 4.38 2.96 $1,167.00 7 6 x 4 3.88 2.87 $1,167.00 8 x 5 3.88 2.78 $1,167.00 8 8 x 6 5 6.60 $2,048.00 4 SIZE X BRANH 2 UP LENGTH EAH (LBS.) OUTLET END TO END PRIE EAH BOX QTY. x 1 2.7 0.91 0.32 $155.50 87 x 1 ¼ 3 0.97 0.38 $155.50 33 x 1 ½ 2.94 1.09 0.38 $155.50 120 x 1 3.25 0.91 0.53 $190.00 66 x 1 ¼ 3.52 0.97 0.59 $190.00 53 2 ½ x 1 ½ 3.45 1.09 0.59 $190.00 66 x 2 3.3 1.34 0.58 $190.00 60 x 1 ½ 3.68 1.09 0.84 $236.00 40 3 x 2 4.10 1.34 0.97 $236.00 40 4 x 2 4.75 1.34 1.76 $438.00 18 ertified to ANSI/NSF 61 ontact an ANVIL representative for details related to these listings. 42

STANDARD PRODUTS Price List ap Fig. 6074 Flange Adapter Fig. 6084 EAH (LBS.) PRIE EAH 2 0.36 $91.00 41 2 ½ 0.50 $134.00 70 3 0.69 $166.50 55 4 1.24 $249.50 30 5 1.97 $280.50 16 6 3.01 $508.50 10 HINGED PIPE OUTSIDE DIAMETER EAH (LBS.) FLANGE () PAINTED 2 2.125 4.60 $531.00 10 2 ½ 2.625 6.20 $552.00 6 3 3.125 6.60 $579.00 5 4 4.125 9.30 $635.00 3 5 5.125 10.20 $853.50 3 6 6.125 12.00 $928.50 2 Fig. 6700 Series Butterfly Valve SIZE PIPE OUTSIDE DIAMETER EAH (LBS.) PRIE EAH 2 ½ 2.625 5.90 $1,353.00 2 3 3.125 6.60 $1,486.50 2 4 4.125 11.00 $1,880.00 2 5 5.125 17.60 $2,391.50 2 6 6.125 21.60 $2,556.00 2 ertified to ANSI/NSF 61 ontact an ANVIL representative for details related to these listings. 43

STANDARD PRODUTS Price List Specialty Fittings for Grooved-End Pipe 90 Adapter Elbows Fig. 7055 45 Adapter Elbows Fig. 7056 Gruvlok Representative. APPROX. EAH (LBS) LIST PRIES Gruvlok Adapter Elbows are fabricated steel. QTY. PAINTED GALV. 1 0.60 $181.50 $225.00-1 ¼ 1.00 $202.50 $225.00-1 ½ 1.20 $259.00 $299.50-2 2.30 $181.50 $225.00-2 ½ 3.70 $314.00 $343.50-3 6.50 $291.50 $356.50-4 11.00 $602.50 $722.50-6 19.80 $899.50 $1,138.00 - Gruvlok Representative. APPROX. EAH (LBS) LIST PRIES Gruvlok Adapter Elbows are fabricated steel. QTY. PAINTED GALV. 1 0.60 $272.50 $297.50-1 ¼ 0.70 $295.00 $315.00-1 ½ 0.80 $297.50 $319.00-2 1.60 $303.50 $371.50-2 ½ 2.20 $307.00 $317.50-3 4.30 $522.50 $560.50-4 7.50 $449.50 $551.00-6 11.10 $1,094.50 $1,211.50 - Reducing Tee Wyes Fig. 7067 Gruvlok Representative. LIST PRIES PIPE SIZE RUN LENGTH EAH (LBS.) PAINTED GALV. QTY. 4 x 3 x 3 16.00 $1,610.50 $1,913.50 - x 4 27.00 $2,287.00 $2,742.00-5 x 3 x 3 25.00 $2,176.00 $2,550.50 - x 5 44.00 $4,104.50 $4,655.00-5 x 4 x 3 21.00 $2,261.50 $2,548.50 - x 4 25.00 $2,597.50 $2,931.50-6 x 4 x 6 61.00 $4,545.50 $5,169.00-6 x 5 x 3 27.00 $2,394.50 $2,724.00 - x 4 31.00 $2,775.50 $3,155.50-8 x 6 x 4 45.00 $4,214.50 $5,113.50 - x 8 95.00 $6,441.50 $7,452.00 - Gruvlok Reducing Laterals are fabricated steel. Additional sizes priced upon request. 44

STANDARD PRODUTS Price List Steel Swaged Nipples Figs. 7077, 7078, and 7079 Gruvlok Representative. Adapter Nipples Figs. 7080, 7081, and 7082 Gruvlok Representative. Fig. 7077 GR x GR 2 2½ 3 Fig. 7078 GR x THD Made of carbon steel conforming to ASTM A106. Fig. 7079 GR x BEV APPROX. EAH (LBS) PAINTED QTY. x 1 2.00 $454.00 - x 1¼ 1.65 $454.00 - x 1½ 2.00 $454.00 - x 1 3.50 $974.50 - x 1¼ 3.50 $974.50 - x 1½ 3.50 $974.50 - x 2 2.85 $866.00 - x 1 5.00 $1,086.00 - x 1¼ 5.00 $1,086.00 - x 1½ 5.00 $1,086.00 - x 2 5.00 $912.00 - x 2½ 5.00 $912.00-3½ x 3 5.25 $2,085.00 - x 1 8.00 $1,543.50 - x 1¼ 8.00 $1,543.50 - x 1½ 8.00 $1,183.50-4 x 2 7.00 $1,183.50 - x 2½ 8.00 $1,356.00 - x 3 8.00 $1,356.00 - x 3½ 7.50 $1,745.50 - x 2 12.00 $1,919.00-5 x 2½ 12.00 $1,919.00 - x 3 11.80 $1,919.00 - x 4 12.00 $1,919.00 - x 1 17.00 $3,824.50 - x 1¼ 17.00 $3,824.50 - x 1½ 20.00 $3,824.50 - x 2 15.20 $3,128.50-6 x 2½ 15.80 $3,128.50 - x 3 15.60 $3,128.50 - x 3½ 19.00 $3,128.50 - x 4 19.00 $1,874.00 - x 5 17.00 $1,874.00 - Fig. 7080 GR x GR Fig. 7081 GR x MPT Fig. 7082 GR x BEV PRIE PER LENGTH - 4 6 8 10 12 ¾ $64.50 $93.00 $115.50 $127.50 $144.00 1 $64.50 $101.00 $110.50 $127.50 $144.00 1 ¼ $64.50 $101.00 $110.50 $127.50 $144.00 1 ½ $64.50 $101.00 $116.50 $133.50 $152.50 2 $64.50 $101.00 $116.50 $133.50 $152.50 2 ½ $74.00 $135.00 $135.00 $156.50 $178.00 3 $145.00 $145.00 $173.50 $202.50 $231.00 4 $146.00 $146.00 $239.00 $282.00 $324.50 5 $300.00 $300.00 $417.00 $514.00 $593.00 6 $384.50 $384.50 $496.00 $576.00 $656.50 8 $430.50 $430.50 $571.50 $784.50 $880.50 10 $555.00 $559.50 $602.50 $928.00 $1,103.00 12 $754.50 $711.50 $754.50 $1,173.50 $1,398.50 Unless otherwise specified, Adapter Nipples for nominal pipe sizes 6" and smaller are made from Schedule 40 pipe; for nominal sizes 8" and larger, from Schedule 30 pipe. For Galvanized or Zinc Plated pricing, add 50% to list price. Special lengths and heavier wall thickness nipples are priced on application. Adapters not shown are available from JB Smith; contact Anvil for availability. Adapter Nipples, Plain End Figs. 7080P, 7081P, and 7082P APPROX. EAH (LBS) PRIE PER LENGTH - 4 6 2 $64.50 $101.00 1.80 2 ½ $74.00 $135.00 0.01 3 $90.00 $145.00 3.70 4 $146.00 $146.00 5.00 6 $384.50 $384.50 9.50 8 $430.50 $430.50 14.27 10 $555.00 $559.50-12 $754.50 $754.50 26.76 45

STANDARD PRODUTS Price List Plain-End Fittings (For use with Fig. 7005 oupling only) 90 Elbows Fig. 7050P APPROX. EAH (LBS) Plain-End Fittings are manufactured from fabricated steel. Other sizes available. Priced on application. Plain-End Fittings (For use with 7005 oupling only) QTY. PAINTED GALV. 2 2.70 $646.50 $712.50-2 ½ 4.80 $756.50 $840.50-3 7.20 $785.00 $878.00-4 12.30 $889.50 $978.00-5 13.40 $1,021.00 $2,048.00-6 31.00 $1,291.00 $1,571.50-8 38.70 $2,424.00 $2,740.50-90 Long Radius Elbows Fig. 7050LRP APPROX. EAH (LBS) QTY. PAINTED GALV. 2 5.10 $669.50 $737.50-2 ½ 9.50 $783.00 $869.50-3 12.80 $813.00 $908.50-4 22.20 $920.50 $1,013.50-5 38.00 $1,058.00 $2,125.00-6 54.00 $1,340.00 $1,629.50-8 92.00 $2,426.00 $2,843.00-45 Elbows Fig. 7051P APPROX. EAH (LBS) PAINTED GALV. 2 2.00 $685.00 $842.50-2 ½ 3.50 $685.00 $842.50-3 4.80 $785.00 $884.50-4 8.00 $818.50 $906.00-5 9.20 $1,022.00 $1,202.50-6 18.50 $1,171.00 $1,374.00-8 24.90 $1,372.00 $1,937.00 - Plain-End Fittings are manufactured from fabricated steel. Other sizes available. Priced on application. Plain-End Fittings (For use with 7005 oupling only) QTY. 45 Long Radius Elbows Fig. 7051LRP APPROX. EAH (LBS) PAINTED GALV. 2 1.80 $711.00 $873.00-2 ½ 3.60 $711.00 $873.00-3 4.50 $815.00 $873.00-4 7.50 $850.00 $938.00-5 13.70 $1,064.00 $1,245.50-6 17.30 $1,218.50 $1,425.50-8 34.00 $1,428.50 $2,009.00 - QTY. Tee Fig. 7060P APPROX. EAH (LBS) PAINTED GALV. 2 3.50 $528.00 $592.00-2 ½ 6.20 $687.50 $778.50-3 8.60 $1,056.50 $1,206.00-4 13.80 $1,512.50 $1,890.50-5 21.70 $2,068.50 $2,465.00-6 30.90 $1,799.50 $2,066.00-8 61.10 $2,593.50 $3,104.00 - QTY. ross Fig. 7068P APPROX. EAH (LBS) Plain-End Fittings are manufactured from fabricated steel. Other sizes available. Priced on application. Plain-End Fittings (For use with 7005 oupling only) PAINTED GALV. 2 4.40 $800.00 $1,006.50-2 ½ 7.80 $800.00 $1,006.50-3 10.70 $949.00 $1,072.00-4 17.00 $1,303.00 $1,464.50-5 26.70 $1,848.50 $2,178.00-6 37.70 $2,440.00 $2,954.00-8 74.60 $3,130.00 $3,820.50 - QTY. 46 Lateral Fig. 7069P APPROX. EAH (LBS) PAINTED GALV. 2 5.10 $712.50 $865.50-2 ½ 9.50 $819.50 $964.50-3 12.80 $973.00 $1,143.50-4 22.20 $1,339.50 $1,499.50-5 38.00 $2,271.00 $2,696.50-6 54.00 $2,343.50 $2,843.00-8 92.00 $3,930.50 $4,628.50 - QTY. True WYE Fig. 7071P APPROX. EAH (LBS) Plain-End Fittings are manufactured from fabricated steel. Other sizes available. Priced on application. Plain-End Fittings (For use with 7005 oupling only) PAINTED GALV. 2 3.50 $704.50 $793.00-2 ½ 6.20 $704.50 $793.00-3 8.50 $791.00 $905.50-4 14.00 $1,173.00 $1,350.00-5 21.60 $1,427.50 $1,676.50-6 31.20 $1,964.00 $2,319.00-8 53.60 $2,543.00 $3,102.50 - QTY. Bull Plug Fig. 7075P APPROX. EAH (LBS) QTY. 2 2.30 $318.00-2 ½ 3.00 $318.00-3 4.50 $464.50-4 7.40 $598.00-5 12.50 $1,300.50-6 17.00 $1,402.50-8 29.00 $2,593.50 -

STANDARD PRODUTS Price List Fabricated Steel Reducing Tees Fig. 7061P LIST PRIES BRANH EAH (LBS.) BLAK GALV. QTY. 3 x 3 x 2 7.10 $476.00 $1,050.50 - x 2 11.30 $656.50 $819.00-4 x 4 x 2½ 11.60 $675.50 $839.00 - x 3 11.90 $675.50 $844.50 - x 2 24.60 $1,148.50 $1,405.00-6 x 6 x 3 25.40 $1,144.50 $1,478.50 - x 4 26.20 $1,214.00 $1,472.50 - x 2 42.00 $1,477.00 $1,884.00 - x 3 44.00 $1,547.50 $1,973.00-8 x 8 x 4 46.00 $1,306.50 $1,988.00 - x 5 48.00 $1,618.00 $2,077.00 - x 6 50.00 $1,524.00 $2,091.50 - x 4 74.00 $2,418.50 $3,020.50-10 x 10 x 6 78.00 $2,459.00 $3,198.50 - x 8 86.00 $2,459.00 $3,257.50 - x 6 112.00 $3,576.50 $4,639.00-12 x 12 x 8 118.00 $3,585.50 $4,684.50 - x 10 130.00 $3,717.50 $4,923.00 - Flange Nipples Fig. 7084P APPROX. EAH (LBS) BLAK GALV. 2 6.00 POA POA - 2½ 9.20 POA POA - 3 10.40 POA POA - 4 19.10 POA POA - 5 23.00 POA POA - 6 29.50 POA POA - 8 43.50 POA POA - ontact your Anvil Representative for pricing. QTY. Flange Nipples Fig. 7085P APPROX. EAH (LBS) BLAK GALV. 2 8.20 POA POA - 2½ 11.90 POA POA - 3 15.50 POA POA - 4 28.00 POA POA - 5 35.00 POA POA - 6 50.00 POA POA - 8 72.00 POA POA - ontact your Anvil Representative for pricing. QTY. 47

STANDARD PRODUTS Price List Stainless Steel Fittings & ouplings Figure 7400SS Rigidlite Type 316 Stainless Steel ouplings PIPE SIZE PIPE OUTSIDE DIAMETER (INHES ) APPROX. EAH (LBS) OUPLING OMPLETE WITH EP OR T GASKET () OUPLING OMPLETE WITH O GASKET (PRIE EAH) All bolts are hex head design Type 316 Grade B-8M lass 1 stainless steel to ASTM A-193. Type 316 Grade 8M stainless steel heavy hex nuts, conforming to ASTM A-194. Weights are approximate and subject to change. BOLTS & NUTS QUANTITY QUANTITY SIZE INHES 1 ¼ 1.660 1.43 40 $272.00 $704.50 2 ³/₈ x 2¼ 1 ½ 1.900 1.69 35 $273.00 $749.00 2 ³/₈ x 2¼ 2 2.375 2.10 28 $305.00 $681.00 2 ³/₈ x 2¼ 2 ½ 2.875 2.37 25 $335.00 $770.50 2 ³/₈ x 2¼ 3 3.500 3.10 18 $374.00 $857.00 2 ½ x 2¾ 4 4.500 4.40 12 $471.50 $1,274.00 2 ½ x 2¾ 6 6.625 7.62 6 $1,087.50 $2,169.50 2 ¾ x 3 8 8.625 12.83 4 $2,265.50 $3,560.00 2 ¾ x 3 Flange Adapter Fig. 7084SS PIPE SIZE SH 10 304 SS SH 10 316 SS 2 $860.00 $876.00 2 ½ $1,210.50 $1,306.50 3 $1,249.00 $1,348.50 4 $1,746.00 $1,885.00 5 $2,154.00-6 $2,350.50 $2,513.50 8 $3,208.50 $3,845.50 10 $4,375.50-12 $7,247.50 - Orders for items in shaded areas cannot be canceled or returned. 48

STANDARD PRODUTS Price List 90 Degree Elbows Fig. 7050SS 45 Degree Elbows Fig. 7051SS SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL 7050SS-1004 A7050SS-1004 7050SS-1016 A7050SS-1016 1 $163.50 $163.50 $171.50 $171.50 1 ¼ $142.00 $142.00 $175.00 $175.00 1 ½ $142.00 $142.00 $175.00 $175.00 2 $191.50 $191.50 $196.50 $196.50 2 ½ $252.50 $252.50 $266.00 $266.00 3 $257.00 $257.00 $318.50 $318.50 4 $366.00 $366.00 $455.50 $455.50 5 $2,440.00 $2,440.00 $2,745.00 $2,745.00 6 $962.50 $962.50 $1,201.50 $1,201.50 8 $1,672.00 $1,672.00 $2,086.50 $2,086.50 10 $3,299.00 $3,299.00 $4,122.00 $4,122.00 12 $5,169.50 $5,169.50 $6,459.50 $6,459.50 Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL 7051SS-1004 A7051SS-1004 7051SS-1016 A7051SS-1016 1 $132.00 $132.00 $156.00 $156.00 1 ¼ $132.00 $132.00 $157.00 $157.00 1 ½ $137.50 $137.50 $159.50 $159.50 2 $168.00 $168.00 $175.50 $175.50 2 ½ $220.00 $220.00 $230.50 $230.50 3 $237.00 $237.00 $293.00 $293.00 4 $338.00 $338.00 $419.50 $419.50 5 $2,934.50 $2,934.50 $3,270.00 $3,270.00 6 $636.00 $636.00 $794.00 $794.00 8 $1,086.50 $1,086.50 $1,357.50 $1,357.50 10 $2,539.50 $2,539.50 $2,970.50 $2,970.50 12 $3,504.50 $3,504.50 $4,381.00 $4,381.00 Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. Stainless Steel aps Fig. 7074SS Tees Fig. 7060SS SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL 7074SS-1004 A7074SS-1004 7074SS-1016 A7074SS-1016 1 $238.50 $238.50 $242.50 $242.50 1 ¼ $250.50 $250.50 $257.00 $257.00 1 ½ $262.50 $262.50 $268.00 $268.00 2 $360.50 $360.50 $368.00 $368.00 2 ½ $334.00 $334.00 $382.50 $382.50 3 $457.50 $457.50 $463.50 $463.50 4 $580.00 $580.00 $591.00 $591.00 5 $1,281.00 $1,281.00 $1,403.00 $1,403.00 6 $701.50 $701.50 $705.50 $705.50 8 $1,586.00 $1,586.00 $1,661.00 $1,661.00 10 $2,165.50 $2,165.50 $2,173.50 $2,173.50 12 $2,501.00 $2,501.00 $2,529.50 $2,529.50 Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL 7060SS-1004 A7060SS-1004 7060SS-1016 A7060SS-1016 1 $511.50 $511.50 $532.50 $532.50 1 ¼ $599.00 $599.00 $824.00 $824.00 1 ½ $475.00 $475.00 $497.00 $497.00 2 $513.00 $513.00 $520.50 $520.50 2 ½ $573.50 $573.50 $634.00 $634.00 3 $657.00 $657.00 $820.50 $820.50 4 $703.50 $703.50 $878.50 $878.50 5 $3,287.50 $3,287.50 $3,757.00 $3,757.00 6 $1,367.00 $1,367.00 $1,916.50 $1,916.50 8 $2,018.00 $2,018.00 $3,562.50 $3,562.50 10 $3,945.50 $3,945.50 $9,098.00 $9,098.00 12 $5,945.50 $5,945.50 $11,598.50 $11,598.50 Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. 49

STANDARD PRODUTS Price List Reducing Tees Fig. 7061SS oncentric Reducers Fig. 7072SS SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL SIZE 7061SS-1004 A7061SS-1004 7061SS-1016 A7061SS-1016 1½ x 1 $449.00 $449.00 $551.50 $551.50 x 1¼ $458.50 $458.50 $564.00 $564.00 2 2½ 3 4 6 8 10 12 x 1 $483.50 $483.50 $569.50 $569.50 x 1¼ $543.50 $543.50 $739.00 $739.00 x 1½ $614.50 $614.50 $739.00 $739.00 x 1 $615.50 $615.50 $755.50 $755.50 x 1½ $694.50 $694.50 $758.50 $758.50 x 2 $730.00 $730.00 $746.50 $746.50 x 1 $616.00 $616.00 $706.00 $706.00 x 1¼ $729.50 $729.50 $869.00 $869.00 x 1½ $758.50 $758.50 $912.00 $912.00 x 2 $812.50 $812.50 $1,159.00 $1,159.00 x 2½ $782.50 $782.50 $974.00 $974.00 x 2 $920.50 $920.50 $1,101.00 $1,101.00 x 2½ $1,031.00 $1,031.00 $1,177.50 $1,177.50 x 3 $1,080.50 $1,080.50 $1,347.50 $1,347.50 x 1½ $2,379.00 $2,379.00 $2,927.50 $2,927.50 x 2 $1,952.00 $1,952.00 $2,297.00 $2,297.00 x 2½ POA - - - x 3 $1,392.50 $1,392.50 $1,737.50 $1,737.50 x 4 $1,725.50 $1,725.50 $2,059.50 $2,059.50 x 4 $4,063.50 $4,063.50 $4,851.50 $4,851.50 x 6 $5,327.00 $5,327.00 $6,530.50 $6,530.50 x 6 $6,499.50 $6,499.50 $8,285.00 $8,285.00 x 8 $6,557.00 $6,557.00 $8,356.50 $8,356.50 x 8 $9,367.00 $9,367.00 $11,691.00 $11,691.00 x 10 $11,197.00 $11,197.00 $13,972.50 $13,972.50 Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL SIZE 7072SS-1004 A7072SS-1004 7072SS-1016 A7072SS-1016 1½ x 1 $318.00 - $369.50 $369.50 x 1¼ $353.00 $353.00 $385.00 $385.00 2 2½ 3 4 5 6 8 10 12 x 1 $257.50 $257.50 $304.00 $304.00 x 1¼ $713.50 $713.50 $902.00 $902.00 x 1½ $305.00 $305.00 $349.50 $349.50 x 1½ $689.00 $689.00 $738.00 $738.00 x 2 $427.00 $427.00 $438.50 $438.50 x 1 $735.50 $735.50 $958.50 $958.50 x 1¼ $1,056.50 $1,056.50 $1,281.00 $1,281.00 x 1½ $719.00 $719.00 $858.00 $858.00 x 2 $229.50 $229.50 $339.50 $339.50 x 2½ $188.50 $188.50 $234.00 $234.00 x 2 $306.00 $306.00 $534.50 $534.50 x 2½ $419.50 $419.50 $788.50 $788.50 x 3 $218.00 $218.00 $272.00 $272.00 x 3 $915.50 $915.50 $1,159.00 $1,159.00 x 4 $1,037.00 $1,037.00 $1,281.00 $1,281.00 x 2 $3,050.00 $3,050.00 $6,710.00 $6,710.00 x 2½ $3,516.00 $3,516.00 $4,444.00 $4,444.00 x 3 $703.50 $703.50 $877.00 $877.00 x 4 $534.50 $534.50 $666.00 $666.00 x 5 $2,048.00 $2,048.00 - - x 3 $4,636.00 $4,636.00 $4,879.50 $4,879.50 x 4 $2,558.50 $2,558.50 $3,197.50 $3,197.50 x 6 $1,343.50 $1,343.50 $1,675.50 $1,675.50 x 4 $4,209.00 $4,209.00 $5,184.50 $5,184.50 x 6 $3,168.50 $3,168.50 $3,960.50 $3,960.50 x 8 $3,540.00 $3,540.00 $4,424.00 $4,424.00 x 6 $6,710.00 $6,710.00 $7,929.50 $7,929.50 x 8 $4,822.00 $4,822.00 $6,026.00 $6,026.00 x 10 $4,431.50 $4,431.50 $5,536.50 $5,536.50 Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. 50

STANDARD PRODUTS Price List Eccentric Reducer Fig. 7073SS High Pressure Rigid oupling Fig. 770 SH 10, 304 SS SH 10, 316 SS DOMESTI GLOBAL DOMESTI GLOBAL SIZE 7073SS-1004 A7073SS-1004 7073SS-1016 A7073SS-1016 1¼ x 1 $1,586.00 $1,586.00 $1,769.50 $1,769.50 1½ x 1 $693.00 $693.00 $796.50 $796.50 x 1¼ $1,769.50 $1,769.50 $1,891.50 $1,891.50 2 x 1 $1,386.50 $1,386.50 $1,386.50 $1,386.50 x 1¼ $1,491.00 $1,491.00 $1,591.00 $1,591.00 x 1½ $787.00 $787.00 $902.00 $902.00 2½ x 2 $956.50 $956.50 $1,166.00 $1,166.00 x 1 $2,622.50 $2,622.50 $2,805.50 $2,805.50 3 4 5 6 8 10 12 x 2 $967.50 $967.50 $1,053.00 $1,053.00 x 2½ $982.50 $982.50 $1,129.00 $1,129.00 x 2 $2,588.00 $2,588.00 $3,752.00 $3,752.00 x 2½ $1,206.00 $1,206.00 $2,048.50 $2,048.50 x 3 $2,009.50 $2,009.50 $2,508.00 $2,508.00 x 3 $3,903.50 $3,903.50 $4,696.50 $4,696.50 x 4 $4,209.00 $4,209.00 $4,696.50 $4,696.50 x 2 $5,123.50 $5,123.50 $5,550.50 $5,550.50 x 2½ $3,516.00 $3,516.00 $4,453.00 $4,453.00 x 3 $5,806.00 $5,806.00 $6,099.50 $6,099.50 x 4 $2,120.50 $2,120.50 $3,101.00 $3,101.00 x 3 $9,027.50 $9,027.50 $10,491.00 $10,491.00 x 4 $8,783.00 $8,783.00 $10,369.00 $10,369.00 x 6 $6,710.00 $6,710.00 $7,197.50 $7,197.50 x 6 $11,039.50 $11,039.50 $12,259.50 $12,259.50 x 8 $11,284.00 $11,284.00 $12,504.50 $12,504.50 x 6 $12,137.50 $12,137.50 $14,638.50 $14,638.50 x 8 $13,418.50 $13,418.50 $15,858.00 $15,858.00 x 10 $12,808.50 $12,808.50 $14,638.50 $14,638.50 PIPE SIZE PAINTED GALVANIED 2 $88.50 $120.00 2 ½ $101.50 $136.50 3 $113.00 $153.00 4 $164.00 $233.50 6 $295.00 $424.00 8 $471.00 $676.50 10 $870.00 $1,190.00 12 $1,266.50 $1,694.50 Orders for items in shaded areas cannot be canceled or returned. Butterfly Valve Fig. B333 SIZE LIST PRIE 14 $7,120.50 16 $9,741.00 18 $11,988.50 20 $16,222.00 24 $20,657.50 Orders for items in shaded areas cannot be canceled or returned. Orders for items in shaded areas cannot be canceled or returned. Some sizes available in Schedule 40 - these orders cannot be canceled or returned. ontact your Sales Representative for more information. 51

STANDARD PRODUTS Price List Low Profile Butterfly Valve Fig. B8101 Grooved Dual Disk heck Valve Fig. V890 SIZE LIST PRIE 2 $740.00 2 ½ $941.00 3 $1,062.50 4 $1,167.50 5 $2,224.50 6 $2,354.00 Orders for items in shaded areas cannot be canceled or returned. SIZE LIST PRIE 14 $7,119.00 16 $9,703.00 18 $12,808.00 20 $16,836.00 24 $21,227.00 Orders for items in shaded areas cannot be canceled or returned. Grooved Ball Valve Fig. BV835 Grooved Butterfly Valve Fig. B8200L SIZE LEVER HANDLE LIST PRIE GEAR OPERATOR LIST PRIE 1 ½ $413.50 $1,096.50 2 $458.50 $1,536.50 2 ½ $998.50 $2,017.50 3 $1,612.00 $2,857.00 4 $2,493.00 $3,639.00 6 $7,645.50 $8,582.00 SIZE LIST PRIE 2 $457.50 3 $598.50 4 $770.00 6 $1,284.00 8 $1,534.50 Orders for items in shaded areas cannot be canceled or returned. 52