APV DELTA SVS1F INSTRUCTION MANUAL BUTTERFLY VALVE. Scan for SV1/SVS1F Valve Maintenance Video

INSTRUCTION MANUAL APV DELTA SVSF BUTTERFLY VALVE FORM NO.: H74933 REVISION: UK-8 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. Scan for SV/SVSF Valve Maintenance Video

UK EU Declaration of Conformity for Valves and Valve Manifolds SPX FLOW TECHNOLOGY GERMANY GMBH Gottlieb-Daimler-Str. 3, D-59439 Holzwickede herewith declares that the APV double seal and double seat valves of the series SD4, SDT4, SDU4, SDMS4, SDMSU4, SDTMS4, SWcip4, DSV, DA3, DA3SLD, DE3, DEU3, DET3, DKR, DKRT, DKRH in the nominal diameters DN 5-50, ISO 6 and Sh5-6 Sh5 APV butterfly valves of the series SV and SVSF, SVL and SVSL in the nominal diameters DN 5-00, DN 5-50 and ISO 4 APV ball valves of the series KHI, KHV in the nominal diameters DN 5-00 APV single seat, diaphragm and spring loaded valves of the series S, SW4, SWhp4, SW4DPF, SWmini4, SWT4, SWS4, MF4, MS4, MSP4, AP/T, CPV, RG4, RG4DPF, RGMS4, RGE4, RGE4DPF, RGEMS4, PR, PRD, SI, UF/R3, VRA/H in the nominal diameters DN 0-50, ISO / 4 and Sh5-6 Sh5 and the valve manifolds installed thereof meet the requirements of the Directives 006/4/EC (superseding 89/39/EEC and 98/37/EC) and ProdSG (superseding GPSG - 9.GPSGV). For official inspections, SPX FLOW presents a technical documentation according to Appendix VII of the Machinery Directive, this documentation consisting of documents of the development and construction, description of measures taken to meet the conformity and to correspond with the basic requirements on safety and health, incl. an analysis of the risks, as well as an operating manual with safety instructions. The conformity of the valves and valve manifolds is guaranteed. Authorised person for the documentation: Frank Baumbach SPX FLOW TECHNOLOGY GERMANY GMBH Gottlieb-Daimler-Str. 3, D-59439 Holzwickede, Germany November 07 Frank Baumbach Regional Engineering Manager, F&B Components

APV UK APV_SVSF_UK-8_0807.qxp Table of Contents Page. General Terms. Safety Instructions - 3 3. Intended Use 3 4. Mode of Operation 4 4.. General terms 5. Auxiliary Equipment 5-7 5.. Valve position indication - actuated valve (proximity switches) 5.. Valve position indication - manually operated valve (proximity switches) 5.3. Handle with adjusting device 5.4. Control Unit 5.5. Adapter for control unit 5.6. Turning actuator for control unit 6. Cleaning 8 7. Installation 8-9 7.. Connections 7.. Welding instructions 8. Dimensions / Weights 0-9. Technical Data - 3 9.. General data 9.. Compressed air quality 9.3. Kvs values 9.4. Opening / closing times 9.5. Torques 9.6. Control air consumption 0. Materials 4. Maintenance 5. Service Instructions 6-8.. Disassembly from the line system.. Disassembly of actuating device.3. Dismantling of inner parts.4. Replacement of seals.5. Installation of seals and bearing bushes.6. Installation of actuating device.7. Installation of feedback units 3. Spare Parts Lists 9 (see attachment) SVSF - FZ CU DN 5-00, -4 - RN 0.038.004 SVSF - H DN 5-00, -4 - RN 0.038.000 - Handle SV-HL valve position indication - RN 0.037.0 DN5-00, - 4 Turning actuator K-80, K-5, K-80 spring/air - RN 0.073 Turning actuator spring/air for feedback unit - RN 0.076 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp. General Terms This instruction manual has to be read carefully and observed by the responsible operating and service personnel. We do not accept any liability for damage or malfunctions resulting from the non-compliance with this instruction manual. Descriptions and data given herein are subject to technical changes.. Safety Instructions The valve must only be assembled, disassembled and reassembled by persons who have been trained in APV valves or by SPX FLOW service team members. If necessary, contact your local SPX FLOW representative. DANGER!!!!!! - The technical safety symbol draws your attention to important directions for operating safety. You will find it wherever the activities described are bearing health hazards or risks for persons or material assets. - Do not reach into the open valve or into the yoke! Risk of ibruising at movable parts of the valve. - In dismantled state there is the risk of injury by sudden valve operation. - Regular maintenance including replacement of seals and bearing bushes must be scheduled for the valve in order to prevent leakages and discharge of liquids. - Before any maintenance of the valve, the line system must be depressurized and discharged if possible. - Electric and pneumatic connections must be separated. - Observe the following Service Instructions to ensure safe maintenance of the valve. Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp. Safety Instructions! - DANGER! Welded actuators are preloaded by spring force. Opening of the actuators is strictly forbidden. Danger to life! Actuators which are no longer used and / or defective must be disposed in professional manner. Defective actuators must be returned to your local SPX FLOW representative for their professional disposal and free of charge for you. Please address to your local SPX FLOW representative. 3. Intended Use The intended use as field of application of the butterfly valve is the shut-off of pipeline sections. Arbitrary, structural changes at the valve may affect safety as well as the intended functionality of the valve and are not permissible. Authorizations and External Approvals: ATEX (Directive 04/34/EU) 3 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 4. Mode of Operation 4.. General terms Use of high-quality stainless steel and seal materials to the specified requirements, the butterfly valve range DELTA SVSF is applicable in the food and beverage industries as well as in the chemical and pharmaceuticl industries. Valves of the series DELTA SVSF can either be operated manually or remote controlled via a pneumatic actuator. Manual operation and pneumatic actuator including add-on pieces are interchangeable. In the standard design NC, the pneumatic turning actuator opens the valve with compressed air. Reset by spring force into the limit position closed. Extension of operating time of actuated valves by pneumatic air throttle or adjusting screw in the control unit to optimize the flow behaviour and to reduce the risk of pressure hammers in installations if necessay. The butterfly valve can also be used in vacuum systems. The valve opens and closes by turning the disc by 90. Smooth valve passage without diversion of line flow. The opening diameter complies with the size of the inner line diameter. Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 4

APV UK APV_SVSF_UK-8_0807.qxp 5. Auxiliary Equipment 5.. Valve position indication - valve with pneumatic actuator Proximity switches to signal the limit position of the valve disc can be installed in the yoke area if required. We recommend to use our APV standard proximity switches. Type: three-wire proximity switch (ref.-no. 08-60-0/93; H63) Operating distance: 4mm / diameter: mm / length: 30 mm. Feedback complete with support and proximity switch (ref.-no. 5-33-03/93; H375) for a limit position. Using a valve position indicator other than APV, we cannot guarantee faultless function. 5.. Valve position indication - valve with manual operation Specific manual actuations with feedback feature are available: a) Feedback of the disc position closed (simple variant). b) Feedback of both disc positions open and closed is possible. 5.3. Manual operation with adjusting device As a special design, a handle is available which provides for the fixation of intermediate positions of the flap beside the two limit positions. 5 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 5. Auxiliary Equipment fig. 5.4. Control Unit CU4 5.4. Control unit (CU, fig. 5.4.) Units with feedback switch and magnet valve for the pneumatic control of the valve for assembly on the actuator are also available in fieldbus technology. The assembly of a control unit on a pneumatic actuator is possible. The following different designs are available: Control Unit CU3 Direct Connect AS-i extended 6 slaves DeviceNet Profibus CU4-T-Direct Connect 08-45 - 0/93; H3046 CU4-T-AS-i extended 08-45 - /93; H30468 CU3 DeviceNet 6-3 - 40/93; H094 CU3 Profibus 08-45 - 00/93; H35495 5.5. Adapter for control unit (fig. 5.5.) CU3 Profibus, CU3 DeviceNet The following adapters are required to install the control unit on the SVSF valve: fig. 5.5. Spare parts for CU adapter Item Pcs. Designation reference No. ID-No. - - CU adapter K080 SVSF, DKR 000 08-48-46/93 H0943 CU operating cam compl. SVS/DKR 000 08-60-779/93 H08853 3 9 4 5 6 8 7 * 3 cyl. screw ISO07 M5x8-A-7 3 adapter set - 4 o-ring 88,6-,78 NBR - 5 o-ring 5,8-,78 NBR - 6 CU adapter for SVS,DKR 7* o-ring 90- NBR * scope of supply actuator 8 o-ring 3,0-,0 NBR 70 9 blind plug G/8" 000 08-60-760/5 H08835 000 08-60-333/93 H3044 000 58-06-387/83 H08639 000 58-06-044/83 H08640 000 08-60-78/93 H08803 000 58-06-46/83 H4335 000 58-06-049/83 H0864 000 08-60-740/93 H0885 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 6

APV UK APV_SVSF_UK-8_0807.qxp 5. Auxiliary Equipment fig. 5.5.. 6 5.5.. Adapter for control unit (fig. 5.6..) CU4-T-Direct Connect, CU4-T-AS-i extended The following adapter is required to install the control unit CU4 on the SVSF valve: Spare parts for CU4 T- adapter 5 7 4 Item Pcs. Designation - - CU4 T-adapter cpl. reference No. ID-No. 000 08-48-60/93 H 30475 8 3 9 CU4 T-adapter 3 3 cyl. screw ISO07 M5x6-A-70 o-ring - NBR 55 Shore A 4 o-ring 6- NBR 5 o-ring 0,7-,6 6 CU4-operating cam complete 7 CU4 SVS, DKR operating rod 8 CU4 clamp halves complete 9 cy. screw ISO 476 M4x40 inner hexagon 000 08-46-57/93 H39875 000 65-05-054/3 H79000 000 58-06-034/83 H3897 000 58-06-059/83 H30505 000 58-06-493/83 H48389 000 08-60-900/93 H30479 000 08-60-905/93 H30480 000 08-46-569/93 H39873 000 65-05-040/3 H30360 5.6. Turning actuator for control unit - For the assembly of a control unit on the butterfly valve a special turning actuator is required. The standard turning actuator must be replaced. Turning actuator for control unit DN 5-00 / K080 F/L Inch - 4 / K080 F/L ref.-no.: 000-5 - 37-070/7 H3937 7 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 6. Cleaning 6.. Cleaning recommendation The valve passage is cleaned by cleaning liquids during cleaning of the connected pipelines. Depending on the degree and constituents of soiling, the cleaning liquids, times and processes must be scheduled for the individual application. The compatibility of the individually selected cleaning processes and liquids with the respectively used seals must be verified. 7. Installation In normal installation position, the actuator is positioned vertically to the top. Depending on the respective application, optional installation positions can, however, also be realized. SVSF valves are equipped for the assembly between FG flanges. Attention: Observe welding instructions. 7.. Connections Standard plain flanges FG between which the valve is installed form part of the scope of supply. The flanges have weld ends in the respective nominal dimension. Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 8

APV UK APV_SVSF_UK-8_0807.qxp 7. Installation 7.. Welding Instructions - Observe the bore position during welding of the mating flanges (see fig. and table). aº aº DN 5 (flange 4 bores) - screws DN 40-65,5-3 (flange 4 bores) - 4 screws DN 80,00 4 (Flange 8 bores) - 6 screws DN Inch aº 5-40,5 8º 50 6º 65,5 4º 3 3º 80, 00 4 45º - Welding may only be carried out by certified welders (DIN EN ISO 9606-). (seam quality DIN EN ISO 587). - The welding of the mating flanges must be effected in such a way that deformation strain cannot be transferred. - TIG orbital welding is the most appropriate method. - Before welding, all sensitive parts must be removed! Dismantle the valve core with seals from between the mating flanges. - After welding of the mating flanges and after work at the pipelines, the corresponding parts of the installation or pipelines must be cleaned from welding residues and soiling. If these cleaning instructions are not observed, welding residues and dirt particles can settle in the valve and cause damage or be carried over to other parts of the installation. - Any damage resulting from the non-observance of these welding instructions is not subject to our guarantee. 9 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 8. Dimensions / Weights SVSF with control unit CU4 Ø 34 SVSF with turning actuator Ø C B Ø C Ø D Ø D B A A Dimensions in mm DN A B B Ø C Ø D Ø E butterfly valve with turning actuator Weights in kg butterfly valve with turning actuator and control unit 5 98 7,5 45,5 85 6 9 5,0 6,0 40 98 80 460 85 38 4 5,7 6,7 50 98 85 465 85 50 53 6,4 7,4 65 98 93,5 473,5 85 66 70 7,0 8,0 80 98 30 48 85 8 85 7,4 8,4 00 98 3 49 85 00 04 8,8 9,8 Inch 98 7,5 45,5 85,6 5 5,0 6,0,5 98 80 460 85 34,8 38 5,7 6,7 98 85 465 85 47,8 5 6,4 7,4,5 98 93,5 473,5 85 60,3 63,5 7,0 8,0 3 98 97 477 85 7,9 76, 7,4 8,4 4 98 3 49 85 97,6 0,6 8,8 9,8 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 0

APV UK APV_SVSF_UK-8_0807.qxp 8. Dimensions / Weights SVSF with manual actuation C Ø E Ø D B Dimensions in mm A DN A B C Ø D Ø E Weights in kg 5 98 88 65 6 9, 40 98 96,5 65 38 4,9 50 98 0,5 65 50 53 3,3 65 98 0 65 66 70 4,0 80 98 7,5 65 8 85 4,8 00 98 7,5 65 00 04 5, Inch 98 88 65,6 5,,5 98 96,5 65 34,8 38,9 98 0,5 65 47,8 5 3,3,5 98 0 65 60,3 63,3 4,0 3 98 3,5 65 7,9 76, 4,8 4 98 7,5 65 97,6 0,6 5, Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 9. Technical Data elbow union - G/8" slewable tightening torque Nm 9.. General data - max. lin pressure : 0bar - max. operating temperature : 35 o C EPDM, HNBR * VMQ, * FPM - short-term load : 40 o C EPDM, HNBR * VMQ, * FPM * (no steam) - vacuum tightness : mbar - opening angle of butterfly valve : 90 o min. air pressure for actuator : 6bar max. air pressure for actuator : 0bar turning actuator K080 F/L - air connection (for hose) : 6x elbow union - G/8" slewable : tightening torque Nm 9.. Compressed air quality: Quality Class acc. to ISO 8573- content of solid particles: Quality Class 3 max. size of solid particles per m³ 0000 of 0,5µm < d,0µm 500 of,0µm < d 5,0µm content of water: Quality Class 3 max. dew point temperature -0 C For installations at lower temperatures or at higher altitudes, additional measures must be considered to reduce the pressure dew point accordingly. content of oil: Quality Class max. 0,0mg/m³ The oil applied must be compatible with Polyurethane elastomer materials. 9.3. kvs values in m³/h DN Inch 5 40 40,5 89 50 60 65,5 50 80 3 440 00 4 630 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 9. Technical Data 9.4. Opening and closing times The actuating times depend on the length of the air line between the magnet valve to the air control and the actuator. For air lines with a length of up to m, the opening time for butterfly valves DN 5/ to DN 00/4 at 6 bar control air pressure amounts to about second. The closing time, after air shut-off, depends on the nominal dimension and amounts to to 3 seconds. If the valves are subject to strong friction, e.g. through dry seals, the actuating times extend accordingly. 9.4.. Opening and closing times for butterfly valves The opening and closing times of valves equipped with a control unit can be adjusted. opening time in sec. control air pres. 6 bar closing time in sec. DN Inch hose length m 5 sec.,5 sec. 40,5 sec.,5 sec. 50 sec.,5 sec. 65,5 sec.,5 sec. 80 3 sec. 3,0 sec. 00 4, sec. 3,5 sec. All time data are approximate values taken from sample measurements. 9.5. Torque Md [Nm] for butterfly valves DN Inch Md [Nm] 5 0 40,5 50 6 65,5 0 80 3 00 4 4 9.6. Control air consumption at 6 bar control pressure turning actuagor K080 (spring/air) per stroke,8 (NL) 3 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp 0. Materials - valve disc.457 /.4404 (DIN EN 0088) - housing flange, mating flange DN 5-00.430 /.4404(DIN EN 0088) - 4.4404 (DIN EN 0088) - SV seal, flange seal standard: option: EPDM HNBR, VMQ, FPM - bearing bush polyamide PA - handle polyamide PA 6.6 Actuator - yoke, actuator.430(din EN 0088) - coupling.4308 (DIN EN 0088) - indicator PE - hard - piston polyacetal POM - spindle bearing polyamide PA - air connection polyamide PA 6.6 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 4

APV UK APV_SVSF_UK-8_0807.qxp. Maintenance Scan for SV/SVSF Valve Maintenance Video - The maintenance intervals depend on the application of the valve and should be determined by the operator carrying out regular checks of the valve. - There are a few wear parts on butterfly valves, principally the SV seal and bearings. - It is recommended that spare seals and bearings are kept by the user. Complete seal kits for the valve service are available (see spare parts lists). - If damaged seals are replaced, generally all seals and bearings should be changed. SV seal grease. - Dismantling and installation of seals according to Service Instructions. - All seals must be slightly greased before their installation. Grease SV seal according to fig. - especially in the cross bores. grease - Assembly of valve and change of valve design NC or NO by installation of the turning actuator according to Service Instructions. - The inner parts of the actuator are maintenance free. grease Attention! Use food-grade special grease being suited for the respective seal material, only. Recommendation: APV assembly grease for EPDM, FPM, HNBR and NBR (0,75 kg /can - ref. No. 000 70-0-09/93; H4738) (60 g /tube - ref. No. 000 70-0-08/93; H4738) or APV assembly grease for VMQ (0,6 kg /can - ref. No. 000 70-0-07/93; H47380) (60 g /tube - ref. No. 000 70-0-06/93; H47379)!!! Do not use grease containing mineral oil for EPDM seals!!!!!! Do not use Silicone-based grease for VMQ seals!!! Less suited grease types can influence the function and life time. 5 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp. Service Instructions.. Dismantling from the line system! Danger!. Shut off connecting lines, let down line pressure and drain pipeline if possible.. Disconnect electric and pneumatic connections. 3. Release clamp connection at support of proximity switches. Pull off proximity switch. 4. Remove the flange screws. 5. Take butterfly valve out of the flanges. Attention! Disassembly from the line system in closed valve state, only!.. Dismantling of the actuating device The item numbers refer to the spare parts drawings. - Manual actuation with limit switch: Screw off fastening screw (4) at the handle () and lift off handle. - Manual actuation with adjusting device: Screw off fastening screw at handle. Release both fastening screws of the scale sheet, lift off handle with indicator and scale. - Pneumatic actuator: Remove the two fastening screws (0) at the yoke (), lift off actuator (7) with yoke to the top. Lift off coupling (6) and position indicator (5). Attention! If valve position indicators are installed, see to the position of the operating cam (see.6. and.7.). - Actuator with control unit: Dismantling of actuator from yoke as described in item Actuator. The control unit needs not be removed from the actuator..3. Dismantling of the inner parts Valve core - Remove all flange passage screws (9) at the circumferences of the valve housing and pull off the valve core. Sealing ring, bearings, valve disc - Remove all fastening screws around the valve housing and part the housing halves (5, 6). - Pull off the inner parts. Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 6

APV UK APV_SVSF_UK-8_0807.qxp. Service Instructions fig. fig. fig. 3 projecting ring on the disc bolt bearing bush bearing bush wrong assembly.4. Replacement of seals. Lift the flange seals (4) out of the groove and replace them. Remove the fastening screws (0) of the valve core and part the housing halves (5, 6).. Turn the disc (8) in the seal ring (7) into open position. 3. Remove the bearing bushes (). 4. By slight pressing, the seal ring (7) is deformed in its longitudinal axis, and, thus, can be pulled off via the short bearing spindle. 5. Pull the seal ring (7) off the actuating spindle. 6. Clean the valve disc (8). 7. Grease the holes of the new seal ring according to chapter 9 and insert the long actuating spindle of the valve disc (8). 8. Turn the disc (8) in the seal ring (7) into open position. 9. With hand pressure the seal ring is deformed in its longitudinal axis, and, thus, can be pushed on via the short bearing spindle..5. Installation of inner parts The current design of the valve disc has a projected ring on the disc bolt (fig. ). The new valve disc can also be installed in old housings.. Place bearings () on the spindle of the disc. The bearing bushes must be flush with the housing flange (fig. ).. Insert the disc (8) in open position with seal ring (7) and bearing bushes () into one housing half (5,6). 3. Assemble the housing halves (5,6) with the screws (6) alternately crosswise. During the assembly of the housing halves, the projecting ring presses into the plastic surface of the bearing bush and secures the bearing bush against longitudinal movement. Attention! Tightening of the screws (0), the valve disc (8) must be in open position. Damage of valve disc seal during assembly in closed position is possible. Bearings must not project the housing flange (fig. 3). bearing bush 7 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

APV UK APV_SVSF_UK-8_0807.qxp. Service Instructions.6. Installation of the actuating device. Observe the steps mentioned in. in reverse order.. With manual butterfly valves, the disc (8) and the handle () are in a line. 3. Attach the position indicator (5) to align with the valve disc onto the square of the actuating spindle of the disc (8). 4. Observe the design of the valve for the installation of the coupling (6) on butterfly valves with feedback: NC = normally closed Valve disc (8) is closed, place coupling (6). The upper operating cam must be adjusted to the upper yoke bore. NO = normally open Valve disc (8) is open, place coupling (6). The lower operating cam must be adjusted to the lower yoke bore. 5. Place actuator (7) with yoke and fasten them with the screws (0)..7. Installation of feedback units (proximity switches) - Valve position indication OPEN: Installation of the feedback unit in the lower yoke bore. - Valve position indication CLOSED: Installation of the feedback unit in the upper yoke bore. - Insert proximity switch support into the yoke bore and fasten it. Introduce the proximity switch into the support until it stops and fix it by the clamp connection. Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8 8

APV UK APV_SVSF_UK-8_0807.qxp 3. Spare Parts Lists The reference numbers of the spare parts for the different valve designs and sizes are included in the attached spare parts drawings with corresponding lists. Please indicate the following data to place an order for spare parts: - number of parts required - reference number - designation. subject to change 9 Butterfly Valve DELTA SVSF Instruction Manual: UK - rev. 8

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF-FZ-CU DN5-00 -4 zoll S Butterfly valve SVSF-A-CU DN5-00 -4 inch S Datum: 9.0.4 Name: Trytko Datum: Name: 30.0.4 06.07.6 Trytko Trytko SPX FLOW Germany Blatt von 7 RN0.038.004 pos. 6 7 Beschreibung description Material material DN5 " DN40,5" ref.-no. ref.-no. ref.-no. ref.-no. 5 Menge quantity item Verschlussstopfen Kunststoff Lock plug Lagerbuchse PA Bearing 30%GF 3 4 08-74-00/93 H6503 08-0-50/93 DN50 ref.-no. H383 09-5-77/4 09-5-308/4 09-5-377/4 09-5-408/4 09-5-47/4 Flansch FG.4404 09-5-458/4 Flange FG matt/satin fin. H87 H873 H8744 H8750 H876 H8767 Flansch FG.430 09-5-77/ 09-5-308/ 09-5-377/ 9-5-408/ 09-5-47/ 09-5-458/ Flange FG matt/satin fin. H870 H874 H8758 Dichtung FGN EPDM 58-3-77/93 58-3-305/93 58-3-377/93 58-3-405/93 58-3-47/93 58-3-455/93 Seal FGN FDA-konform H7780 H7784 H779 H7796 H77303 H77307 Dichtung FGN FPM 58-3-77/73 58-3-305/73 58-3-377/73 58-3-405/73 58-3-47/73 58-3-455/73 Seal FGN FDA-konform H7779 H7783 H779 H7795 H7730 H77306 Dichtung FGN HNBR 58-3-77/33 58-3-305/33 58-3-377/33 58-3-405/33 58-3-47/33 58-3-455/33 Seal FGN FDA-konform H730 H740 H73 H74 H73 H74 Dichtung FGN VMQ 58-3-77/3 58-3-305/3 58-3-377/3 58-3-405/3 58-3-47/3 58-3-455/3 Seal FGN FDA-konform H7778 H778 H7790 H7794 H7730 H77305 Gehäusehälfte I.4404 09-94-84/4 09-94-36/4 09-94-384/4 09-94-46/4 09-94-434/4 09-94-466/4 Housing half I matt/satin fin. x H3553 x H3558 x H3564 x H3576 x H359 x H3599 Gehäusehälfte I.430 09-94-84/ 09-94-36/ 09-94-384/ 09-94-46/ 09-94-434/ 09-94-466/ Housing half I matt/satin fin. x H355 x x H3563 x x H359 x Gehäusehälfte II.4404 09-94-385/4 09-94-47/4 09-94-435/4 09-94-467/4 Housing half II matt/satin fin. x H3566 x H3578 x H3594 x H360 Gehäusehälfte II.430 09-94-385/ 09-94-47/ 09-94-435/ 09-94-467/ Housing half II matt/satin fin. x H3565 x x H3593 x Dichtung SV EPDM 58-33-78/93 58-33-35/93 58-33-378/93 58-33-45/93 58-33-48/93 58-33-475/93 Seal SV FDA-konform H77435 H7745 H77459 H77477 H77484 H7750 Dichtung SV FPM 58-33-78/73 58-33-35/73 58-33-378/73 58-33-45/73 58-33-48/73 58-33-475/73 Seal SV FDA-konform H77433 H77450 H77457 H77475 H7748 H77500 Dichtung SV HNBR 58-33-78/33 58-33-35/33 58-33-378/33 58-33-45/33 58-33-48/33 58-33-475/33 Seal SV FDA-konform H68744 H6863 H68745 H68930 H6886 H6834 Dichtung SV VMQ 58-33-78/3 58-33-35/3 58-33-378/3 58-33-45/3 58-33-48/3 58-33-475/3 Seal SV FDA-konform H7743 H77449 H77456 H77474 H7748 H77499 " ref.-no.

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF-FZ-CU DN5-00 -4 zoll S Butterfly valve SVSF-A-CU DN5-00 -4 inch S Datum: 9.0.4 Name: Trytko Datum: Name: 30.0.4 06.07.6 Trytko Trytko SPX FLOW Germany Blatt 5 von 7 RN0.038.004 pos. item description Menge quantity Verschlussstopfen Kunststoff Lock plug Lagerbuchse Bearing Flansch FG Flange FG 3 Flansch FG Flange FG Dichtung FGN Seal FGN 4 5 6 7 Dichtung FGN Seal FGN PA 30%GF.4404 matt/satin fin..430 matt/satin fin. EPDM FDA-konform FPM FDA-konform Dichtung FGN HNBR Seal FGN FDA-konform Dichtung FGN VMQ Seal FGN FDA-konform Gehäusehälfte I Housing half I Beschreibung Material material.4404 matt/satin fin. Gehäusehälfte I.430 matt/satin fin. DN65,5" 3" ref.-no. ref.-no. ref.-no. 09-5-477/4 09-5-508/4 09-5-55/4 09-5-57/4 09-5-67/4 09-5-658/4 H878 H8790 H8809 H880 H884 H8830 09-5-477/ 09-5-508/ 09-5-55/ 9-5-57/ 09-5-67/ 09-5-658/ H8779 H8798 H88 58-3-477/93 58-3-505/93 58-3-555/93 58-3-57/93 58-3-67/93 58-3-655/93 H7734 H7738 H7733 H7735 H77339 H77343 58-3-477/73 58-3-505/73 58-3-555/73 58-3-57/73 58-3-67/73 58-3-655/73 H7733 H7737 H7733 H7734 H77338 H7734 58-3-477/33 58-3-505/33 58-3-555/33 58-3-57/33 58-3-67/33 58-3-655/33 H733 H743 H744 H734 H735 H745 58-3-477/3 58-3-505/3 58-3-555/3 58-3-57/3 58-3-67/3 58-3-55/3 H773 H7736 H77330 H7733 H77337 H7734 09-94-484/4 09-94-56/4 09-94-566/4 09-94-534/4 09-94-634/4 09-94-666/4 x H369 x H366 x H3649 x H3644 x H3669 09-94-566/ 09-94-534/ 09-94-484/ 09-94-56/ x H368 x DN80 DN00 ref.-no. ref.-no. 08-74-00/93 H6503 08-0-50/93 08-0-5/93 H383 H3833 09-94-634/ x x H3643 x H3668 Housing half I Gehäusehälfte II.4404 09-94-485/4 09-94-57/4 09-94-567/4 Housing half II matt/satin fin. x H36 x H368 x H365 Gehäusehälfte II.430 09-94-485/ 09-94-57/ 09-94-567/ Housing half II matt/satin fin. x H360 x x Dichtung SV EPDM 58-33-478/93 58-33-55/93 58-33-503/93 58-33-58/93 58-33-68/93 58-33-675/93 Seal SV FDA-konform H77509 H7753 H7758 H77539 H77579 H7760 Dichtung SV FPM 58-33-478/73 58-33-55/73 58-33-503/73 58-33-58/73 58-33-6478/73 58-33-675/73 Seal SV FDA-konform H77507 H77530 H7756 H77537 H77577 H77599 Dichtung SV HNBR 58-33-478/33 58-33-55/33 58-33-503/33 58-33-58/33 58-33-68/33 58-33-675/33 Seal SV FDA-konform H6887 H6935 H6936 H6883 H667 H667 Dichtung SV VMQ 58-33-478/3 58-33-55/3 58-33-503/3 58-33-58/3 58-33-68/3 58-33-675/3 Seal SV FDA-konform H77506 H7759 H7755 H77536 H77576 H77598 4" ref.-no. x H367 09-94-666/ x

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF-Handbetätigung Butterfly valve SVSF-handle DN5-00 ; -4 inch +S Datum: 3.0.4 Name: Trytko Datum: Name: 06.07.6 Trytko SPX FLOW Germany Blatt von 5 RN0.038.000- pos. item Kunststoff Lagerbuchse Bearing Flansch FG Beschreibung description PA 30%GF.4404 matt/satin fin. Flange FG H87 H873 H8744 H8750 H876 H8767 Flansch FG.430 09-5-77/ 09-5-308/ 09-5-377/ 9-5-408/ 09-5-47/ 09-5-458/ Flange FG matt/satin fin. H870 H874 H8758 Dichtung FGN EPDM 58-3-77/93 58-3-305/93 58-3-377/93 58-3-405/93 58-3-47/93 58-3-455/93 Seal FGN FDA-konform H7780 H7784 H779 H7796 H77303 H77307 Dichtung FGN FPM 58-3-77/73 58-3-305/73 58-3-377/73 58-3-405/73 58-3-47/73 58-3-455/73 Seal FGN FDA-konform H7779 H7783 H779 H7795 H7730 H77306 Dichtung FGN HNBR 58-3-77/33 58-3-305/33 58-3-377/33 58-3-405/33 58-3-47/33 58-3-455/33 Seal FGN FDA-konform H730 H740 H73 H74 H73 H74 Dichtung FGN VMQ 58-3-77/3 58-3-305/3 58-3-377/3 58-3-405/3 58-3-47/3 58-3-455/3 Seal FGN FDA-konform H7778 H778 H7790 H7794 H7730 H77305 Gehäusehälfte I.4404 09-94-84/4 09-94-36/4 09-94-384/4 09-94-46/4 09-94-434/4 09-94-466/4 Housing half I matt/satin fin. x H3553 x H3558 x H3564 x H3576 x H359 x H3599 09-94-384/ Gehäusehälfte I.430 09-94-84/ 09-94-36/ 09-94-46/ 09-94-434/ 09-94-466/ Housing half I matt/satin fin. x H355 x x H3563 x x H359 x Gehäusehälfte II.4404 09-94-385/4 09-94-47/4 09-94-435/4 09-94-467/4 Housing half II matt/satin fin. x H3566 x H3578 x H3594 x H360 Gehäusehälfte II.430 09-94-385/ 09-94-47/ 09-94-435/ 09-94-467/ Housing half II matt/satin fin. x H3565 x x H3593 x Dichtung SV EPDM 58-33-78/93 58-33-35/93 58-33-378/93 58-33-45/93 58-33-48/93 58-33-475/93 Seal SV FDA-konform H77435 H7745 H77459 H77477 H77484 H7750 Dichtung SV FPM 58-33-78/73 58-33-35/73 58-33-378/73 58-33-45/73 58-33-48/73 58-33-475/73 Seal SV FDA-konform H77433 H77450 H77457 H77475 H7748 H77500 Dichtung SV HNBR 58-33-78/33 58-33-35/33 58-33-378/33 58-33-45/33 58-33-48/33 58-33-475/33 Seal SV FDA-konform H68744 H6863 H68745 H68930 H6886 H6834 Dichtung SV VMQ 58-33-78/3 58-33-35/3 58-33-378/3 58-33-45/3 58-33-48/3 58-33-475/3 Seal SV FDA-konform H7743 H77449 H77456 H77474 H7748 H77499 DN50 ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. " Menge quantity 3 4 5 6 7 Verschlussstopfen Lock plug Material material DN5 " DN40,5" 08-74-00/93 H6503 08-0-50/93 ref.-no. H383 09-5-77/4 09-5-308/4 09-5-377/4 09-5-408/4 09-5-47/4 09-5-458/4

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF-Handbetätigung Butterfly valve SVSF-handle DN5-00 ; -4 inch +S Datum: 3.0.4 Name: Trytko Datum: Name: 06.07.6 Trytko SPX FLOW Germany Blatt 4 von 5 pos. item description Material material Verschlussstopfen Kunststoff Lock plug Lagerbuchse PA Bearing 30%GF Flansch FG.4404 Flange FG matt/satin fin. 3 Flansch FG.430 Flange FG matt/satin fin. Dichtung FGN EPDM Seal FGN FDA-konform DN65,5" 3" ref.-no. ref.-no. ref.-no. Menge quantity 4 5 6 7 Dichtung FGN Seal FGN Dichtung FGN Seal FGN Gehäusehälfte I Housing half I Gehäusehälfte II Housing half II Gehäusehälfte II Housing half II Dichtung SV Seal SV Dichtung SV Seal SV Dichtung SV Seal SV Dichtung SV Seal SV Beschreibung Dichtung FGN FPM Seal FGN FDA-konform HNBR FDA-konform VMQ FDA-konform Gehäusehälfte I.4404 Housing half I matt/satin fin..430 matt/satin fin..4404 matt/satin fin..430 matt/satin fin. EPDM FDA-konform FPM FDA-konform HNBR FDA-konform VMQ FDA-konform 08-74-00/93 H6503 09-5-477/4 09-5-508/4 09-5-55/4 09-5-57/4 09-5-67/4 09-5-658/4 H878 H8790 H8809 H880 H884 H8830 09-5-477/ 09-5-508/ 09-5-55/ 9-5-57/ 09-5-67/ 09-5-658/ H8779 H8798 H88 58-3-477/93 58-3-505/93 58-3-555/93 58-3-57/93 58-3-67/93 58-3-655/93 H7734 H7738 H7733 H7735 H77339 H77343 58-3-477/73 58-3-505/73 58-3-555/73 58-3-57/73 58-3-67/73 58-3-655/73 H7733 H7737 H7733 H7734 H77338 H7734 58-3-477/33 58-3-505/33 58-3-555/33 58-3-57/33 58-3-67/33 58-3-655/33 H733 H743 H744 H734 H735 H745 58-3-477/3 58-3-505/3 58-3-555/3 58-3-57/3 58-3-67/3 58-3-55/3 H773 H7736 H77330 H7733 H77337 H7734 09-94-484/4 09-94-56/4 09-94-566/4 09-94-534/4 09-94-634/4 09-94-666/4 x H369 x H366 x H3649 x H3644 x H3669 x H367 09-94-484/ 09-94-56/ 09-94-566/ 09-94-534/ 09-94-634/ 09-94-666/ x H368 x x x H3643 x H3668 x 09-94-485/4 09-94-57/4 09-94-567/4 x H36 x H368 x H365 09-94-485/ 09-94-57/ 09-94-567/ x H360 x x 58-33-478/93 58-33-55/93 58-33-503/93 58-33-58/93 58-33-68/93 58-33-675/93 H77509 H7753 H7758 H77539 H77579 H7760 58-33-478/73 58-33-55/73 58-33-503/73 58-33-58/73 58-33-6478/73 58-33-675/73 H77507 H77530 H7756 H77537 H77577 H77599 58-33-478/33 58-33-55/33 58-33-503/33 H6887 H6935 H6936 58-33-478/3 58-33-55/3 H77506 H7759 58-33-58/33 H6883 58-33-503/3 58-33-58/3 H7755 H77536 DN80 DN00 ref.-no. ref.-no. 08-0-50/93 08-0-5/93 H383 H3833 58-33-68/33 H667 58-33-68/3 H77576 4" ref.-no. 58-33-675/33 H667 58-33-675/3 H77598