INSTALL GUIDE DOCUMENT NUMBER 5699 REVISION DATE 7 FIRMWARE OL-HA(RS)-HA6P-[OL-RS-HA6] HARDWARE OL-RS-HA6 ACCESSORIES OL-LOADER (REQUIRED) RF-0/0/50-EDP (OPTIONAL) LINKR (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 7 BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE OF 6 DOC.: #5699 7 VEHICLE LIST - OF FEATURES NOTES MODEL YEAR DATA IMMOBILIZER BYPASS X LOCK START/STANDALONE MOD. ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* AUTOLIGHT CTRL TACHOMETER OUTPUT BRAKE PEDAL STATUS -5 Accord PTS AT* -7 Accord Hybrid PTS AT* -7 Civic PTS AT* -5 CR-V PTS AT* 5-6 CR-V Touring PTS AT* 5-6 Crosstour PTS AT* -5 INSTALL TYPE MAKE RLX PTS AT* HONDA ACURA * WARNING: - No takeover available. Upon opening vehicle door engine will shutdown. - All doors must be closed to remote start vehicle. *Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 7
PAGE OF 6 DOC.: #5699 7 BOX CONTENTS - OF BOX CONTENTS MODULE 0 PIN CONNECTOR T-HARNESS VS LED BLUE BLACK BLACK 6 5 6 8 0 6 8 0 5 7 9 5 7 9 6 8 0 5 7 9 PROGRAMMING BUTTON LED A VS G F B E BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK 9 0 7 8 5 6 VS VS AFTERMARKET HOOD SWITCH AND CABLE MS C D PIN CONNECTOR MS WHITE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 7
PAGE OF 6 DOC.: #5699 7 COMPATIBLE ACCESSORIES - OF RF KIT (accessories sold separately) OMEGA RF KIT (NC) MODULE RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) CARLINK OLCLLINK MODULE TELEMATIC PORT (NC) TELEMATIC KIT (accessories sold separately) LINKR MODULE TELEMATIC PORT (NC) Automotive Data Solutions Inc. 7
PAGE 5 OF 6 DOC.: #5699 7 MODULE LOCATION COMPONENT LOCATOR -5 POLARITY 5-6 WIRE COLOR Civic PTS AT -5 POSITION CR-V/ CR-V Touring PTS AT -7 CONNECTOR TYPE Crosstour PTS AT -7 CONNECTOR COLOR HONDA Accord Hybrid PTS AT -5 CONNECTOR NAME Accord PTS AT YEAR MODEL RLX PTS AT WIRE DESCRIPTION ACURA MAKE TYPE - WIRE CHART - OF Parking Light Blue pin Pink Parking light switch (left of steering column) Horn A0 Orange Steering wheel clock spring connector PTS Harness Smart PCU, under dash, left of steering column Ignition Harness Smart PCU, under dash, left of steering column Parking Light Blue pin Gray Parking light switch (left of steering column) Horn A LtBlue Steering wheel clock spring connector PTS Harness Smart PCU, under dash, left of steering column Ignition Harness Smart PCU, under dash, left of steering column Parking Light Blue pin Gray Parking light switch (left of steering column) Horn A LtBlue Steering wheel clock spring connector PTS Harness Smart PCU, under dash, left of steering column Ignition Harness Smart PCU, under dash, left of steering column Parking Light Blue pin Gray Parking light switch (left of steering column) Horn A LtBlue Steering wheel clock spring connector PTS Harness Smart PCU, under dash, left of steering column Ignition Harness Smart PCU, under dash, left of steering column Parking Light Gray pin Blue Parking light switch (left of steering column) Horn PTS Harness Smart PCU, behind glove box Ignition Harness Smart PCU, behind glove box Parking Light Gray pin Gray Parking light switch (left of steering column) Horn A Orange Steering wheel clock spring connector PTS Harness Smart PCU, under dash, above and right of steering column* Ignition Harness Smart PCU, under dash, above and right of steering column* * If vehicle is equipped with an OEM amplifier, it has to be removed to access Smart PCU. Automotive Data Solutions Inc. 7
PAGE 6 OF 6 DOC.: #5699 7 TYPE - WIRING DIAGRAM - OF MODULE SMART PCU (SEE WIRE CHART FOR LOCATION) VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT 8 PIN PTS CONNECTOR E C VS D 8 PIN PTS HARNESS A 6 5 MS RELAY VS PIN IGNITION CONNECTOR VS B PIN IGNITION HARNESS PARKING LIGHT SWITCH (LEFT OF STEERING COLUMN) 6 8 0 6 8 0 5 7 9 5 7 9 C 6 5 8 7 0 9 PARKING LIGHT - MS BROWN/BLACK - PARKING LIGHT OUTPUT GRAY (NC) EMPTY EMPTY 05 EMPTY 06 PURPLE/GREEN (NC) 07 EMPTY BLUE/GREEN (NC) 09 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN (NC) OPTIONAL 7 8 9 0 5 6 HORN D 6 8 0 5 7 9 GRAY/WHITE - HOOD STATUS INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc. 7
MODULE PROGRAMMING PROCEDURE - OF Set ignition to ON position. ACC ON START 07 ENGINE START STOP Set ignition to ON position. ACC ON START ENGINE START STOP PAGE 7 OF 6 DOC.: #5699 7 ACC Wait, LED will flash GREEN rapidly. Set ignition to position. 09 ON START ENGINE START STOP Wait, LED will turn solid GREEN for seconds. Set ignition to position. ACC ON START ENGINE START STOP WARNING: Disconnect power last. Disconnect module from vehicle. 0 Press UNLOCK on the OEM remote. 05 Connect module to computer and proceed with extended programming. >> If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 06 Connect power first. Connect module to vehicle. Module Programming Procedure completed. Automotive Data Solutions Inc. 7
VALET MODE PROGRAMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. ACC ON START >> PAGE 8 OF 6 DOC.: #5699 7 To exit valet mode: repeat steps to 5. Cycle ignition ON five times [5x /ON] rapidly. ENGINE START STOP Wait, LED will turn solid RED for seconds. Set ignition to position. ACC ON START ENGINE START STOP 05 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 7
AFTERMARKET REMOTE PROGRAMMING - OF PAGE 9 OF 6 DOC.: #5699 7 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. Automotive Data Solutions Inc. 7
PAGE 0 OF 6 DOC.: #5699 7 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP [X] Automotive Data Solutions Inc. 7
PAGE OF 6 DOC.: #5699 7 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN ON ON ON ON FORCE UNLOCK ALL ON FIRST PRESS 05 06 DISABLE LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK MIN 05 MIN 0 MIN 5 MIN 05 5 MIN 06 0 MIN 07 5 MIN 5 MIN SEC 05 SEC SEC 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 0 SEC 07 [Z] SETTINGS MODULE NAVIGATION CHART - OF FACTORY KEYLESS RS SEQUENCE CONFIGURATION 09 MODULE RUN TIME WAIT TO START DELAY 0 *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7
PAGE OF 6 DOC.: #5699 7 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES [Z] SETTINGS MODULE NAVIGATION CHART - OF HORN EVENT TRIGGER CONFIGURATION 5-07 Technical Support only HORN CHIRPS WIDTH DOUBLE LOCK LOCK + UNLOCK LOCK + UNLOCK + START DOUBLE LOCK + START 0 msec 5 msec 60 msec *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. Foot brake is ON. Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 0 5 6 CAN communication failure during RS sequence. REMOTE STARTER ERROR CODES: NOTES Automotive Data Solutions Inc. 7 PAGE OF 6 DOC.: #5699 7
I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Automotive Data Solutions Inc. 7 DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE OF 6 DOC.: #5699 7
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. Disconnect the BLACK 0-PIN connector. Repeat programming procedure. PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed. Automotive Data Solutions Inc. 7 PAGE 5 OF 6 DOC.: #5699 7
INSTALLATION CHECKLIST - OF PAGE 6 OF 6 DOC.: #5699 7 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. 5 Enter vehicle and close the doors. Question : Does the driver side sliding door open? 6 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. 6 YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Question 0: Does the vehicle shut down? Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. Automotive Data Solutions Inc. 7