REPAIR PARTS LIST ASSEMBLY AND OPERATING INSTRUCTIONS ROME. BH Series. Hinge-Wheel Combination Harrows

REPAIR PARTS LIST ASSEMBLY AND OPERATING INSTRUCTIONS ROME BH Series FORM NO. 00B HingeWheel Combination Harrows BH0 BH0 BH0 BH00 BH0 BH0 Effective Serial BH000 and Up. Effective Serial BH000 and Up. Effective Serial BH000 and Up. Effective Serial BH0000 and Up. Effective Serial BH000 and Up. Effective Serial BH000 and Up. ROME PLOW EQUIPMENT CO.,LLC CEDARTOWN, GEORGIA, USA EFFECTIVE DATE : April 0 PRINTED IN USA

INDEX Number Required Page Group Group Name BH0 BH0 BH0 BH00 BH0 BH0,, 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000 00 00 0 00 00A 00A 00 000 00 000 00 000 00 00 000 000 00 00 00 0 00 00 00 00 00 0 000 000B BAX BAX BAX BAX BAX 0B 00 00 B0D 00A 00A 000A 00A 000A 000 00 00 00 00 00 000 Drawbar Assembly Offset Bar Assembly Offset Bar Assembly Offset Bar Assembly Offset Bar Assembly Front Stabilizer Front Stabilizer Rear Stabilizer Rear Stabilizer Pivot Hinge Pivot Hinge Stabilizer Hinge, Front Group of Parts Group of Parts Larch Support Group Larch Support Group Front Gang Carrier Front Gang Carrier Front Gang Carrier Front Gang Carrier Front Gang Carrier Front Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Disk Blade, x,, Cutout Axle, / x / Axle, / x 0/ Axle, / x / Axle, / x / Axle, / x / Disk Spacer Scraper Group, Front Scraper Group, Rear Tapered Roller Bearing Assembly Transport Group, Complete Transport Group, Complete Transport Group, Complete Transport Group, Complete Transport Group, Complete Hydraulic Angle Control, Short Geo. Hydraulic Angle Control, Long Geo. Hydraulic Cylinder, x Hydraulic Cylinder, / x Hydraulic Cylinder, x Hydraulic Cylinder, x Hydraulic Cylinder, x 0 0 0 0 0

Parts List Table of Contents BH Series Harrow Layout Exploded View 000 Drawbar Assembly 00, 00, 0 and 00 Offset Bar Assemblies.. Front Gang Carriers Complete all Models... 0 Rear Gang Carrier Complete Model BH0.. 0 Rear Gang Carrier Complete Model BH0.. 0 Rear Gang Carrier Complete Model BH0.. 0 Rear Gang Carrier Complete Model BH00.. 0 Rear Gang Carrier Complete Model BH0.. 00 Rear Gang Carrier Complete Model BH0.. Front Gang Carriers all Models. Rear Gang Carriers all Models. Gang Assembly Requirements Front Gang Carriers all Models Gang Assembly Requirements Rear Gang Carriers all Models 0 Gang Assembly Disk... 0 Gang Assembly Disk... 00 Gang Assembly Disk... 0 Gang Assembly Disk... 0 Gang Assembly Disk... 0 Gang Assembly Disk (furrow filler disk) 0 Gang Assembly Disk (furrow filler disk) 0 Gang Assembly Disk (furrow filler disk) B0D Tapered Roller Bearing Assembly.. CWPC Heavy Duty Bearing Wear Plate Standard 00 Extra Heavy Duty Bearing Wear Plate Optional.. 00 Front and 00 Rear Scraper Assemblies.. Total Number of Disk Blade Scrapers Required for BHHarrows.. C0A Bag of Wrenches. 00 and 000 Rear Stabilizers 00A and 00A Front Stabilizers.. 00 Front Stabilizer Hinge TBX Jack Assembly (Tongue).. 0 Safety Chain and Shackle Assembly. 00 and 000 Latch Support Assemblies... Transport Assembly Requirements all Models 00A Single Transport Assemblies 00A Dual Transport Assemblies.. 00 Eight Bolt Hub Assembly Complete 00 Hub Assembly Page, 0 0 0, 0

Table of Contents continued Page 00 and 00 Tire and Wheel Assemblies. AW0 Hydraulic Hose Holder. 00 Leveling Control Group. 000 Hydraulic Angle and Transport Group BH0.. 00 Hydraulic Angle and Transport Group BH0.. 000 Hydraulic Angle and Transport Group BH0 and BH00 00 Hydraulic Angle and Transport Group BH0.. 00 Hydraulic Angle and Transport Group BH0.. 000 Hydraulic Angle Control Short Geometry Reference.. 00 Hydraulic Angle Control Long Geometry Reference.. 00 Hydraulic Cylinder x.. 00 Hydraulic Cylinder / x. 00 Hydraulic Cylinder x 00 Hydraulic Cylinder x 000 Hydraulic Cylinder x 0 Safety Decal Group.. 00 Light Group Assembly Optional.. 00A Rear (Trail) Hitch Assembly Optional. 000 and 00 Groups of Parts. Rome Plow Warranty.,,, 0,, 0,

BH Series Harrow Layout

Ref. 0 0A 0 Part Part Name Ref. Part Part Name Ref. Part Part Name 000 * 00 * 00 * 00 * 0 * 00A ** 00xA ** 00 B000H 00 ** 000 ** 00 B000H 00 00 ** 000 ** 00 00 ** 000 * 00 * AL0ZK AL0ZK 00 00 0000B LW00 NC00 0000B LW00 NC00 00 LW NF TBX * NC0S CK0 FW0 00 Drawbar Assembly Offset Bar Assembly Offset Bar Assembly Offset Bar Assembly Offset Bar Assembly Front Stabilizer Front Stabilizer Bushing, Bronze Bushing Rear Stabilizer Rear Stabilizer Bushing, Bronze Bushing Bushing, Bronze Pivot Hinge Pivot Hinge Bushing, Bronze Stabilizer Hinge, Front Group of Parts Group of Parts Grease Fitting Grease Fitting Pin (000 (Parts) Pin (00 (Parts) Bolt, x Lockwasher, Hex Nut, Bolt, / x Gr. Lockwasher, / Hex Nut, / Bolt, Lockwasher, / Nut, / Tongue Jack Slotted Nut, / Cotter Pin, / x / Flatwasher, / Pin (00 Parts) 0 A 00 * 000 * 0000 00 000 00 AG 00 00 RH0 000 00 00 0000B LW00 NC00 00 NC0S CK0 FW0 000 00 00 B LW 000 ** 00 ** 00 ** 00 ** 0 ** 00 ** B000H 0 ** 00 ** 0 ** 0 ** 0 ** 0 ** Latch Support Assembly Latch Support Assembly Latch Support Latch Support Latch Bar Latch Bar Klik Pin Pin Latch Collar Latch Pin Transport Lock Pin Support Beam Bushing, Bronze Bolt, / x Gr. Lockwasher, / Hex Nut, / Pin Slotted Nut, / Cotter Pin, / x / Flatwasher, / Latch Pivot Bolting Bracket, Pivot Bushing Bolt, / x / Gr. Lockwasher, / Front Gang Carrier Front Gang Carrier Front Gang Carrier Front Gang Carrier Front Gang Carrier Front Gang Carrier Bushing Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier Rear Gang Carrier 0 0 B000H C0A * *** 00 *** 000 B00000H 000 0B LW NC 000 B00000H B000H 000 0000B LW00 NC00 00 CK000 000 NCJ 00 00B FW00 Bushing Bag of Wrenches Transport Assemblies Leveling Group of Parts Cylinder Anchor Bushing Spacer Plate Bolt, / x / Lockwasher, / Hex Nut, / Cylinder Pivot Ear Bushing Bushing Sleeve Bolt, x Gr. Lockwasher, Hex Nut, Pin Cotter Pin, / x Stop Bolt Hex Jam Nut, / Pin Bolt, / x / Gr. Flatwasher, / * See separate page for parts list. ** See Index for requirements for each harrow. *** See page for complete Transport Assembly. BH Series Harrow Layout

Ref. Part Number Part Name 0 00 000 RR0B 000B NC0 LW0 0B NC LW LW NC 00B 0 Drawbar Assembly: Drawbar Plate Hitch Clevis Hex Bolt, / x Gr. Hex Nut, / Lockwasher, / Hex Bolt, / x / Gr. Hex Nut, / Lockwasher, / Lockwasher, / Hex Nut, / Hex Bolt, / x Gr. Safety Chain Ref. 000 Drawbar Assembly, Complete

Number Required Ref. Part Number Part Name 00 00 0 00 00B FW B00 LW NC Offset Bar Offset Bar Offset Bar Offset Bar Hex Bolt, / x Gr. Flatwasher, / Bushing Lockwasher, / Hex Nut, / 00 00 0 00 00, 00, 0 and 00 Offset Bar Assemblies

Part Number Part Name 000 0 * 0 * CWPC * 00 * Front Gang Carrier Gang Assembly Disk Blade Gang Assembly Disk Blade Bearing Wear Plate Front Scraper Assembly 000 Front Gang Carrier Complete Model BH0 Part Number Part Name 00 0 * 0 * CWPC * 00 * Front Gang Carrier Gang Assembly Disk Blade Gang Assembly Disk Blade Bearing Wear Plate Front Scraper Assembly 00 Front Gang Carrier Complete Model BH0 Part Number Part Name 00 0 * 0 * CWPC * 00 * Front Gang Carrier Gang Assembly Disk Blade Gang Assembly Disk Blade Bearing Wear Plate Front Scraper Assembly 00 Front Gang Carrier Complete Model BH0 Part Number Part Name 00 00 * 0 * CWPC * 00 * Front Gang Carrier Gang Assembly Disk Blade Gang Assembly Disk Blade Bearing Wear Plate Front Scraper Assembly 0 00 Front Gang Carrier Complete Model BH00 Part Number Part Name 0 00 * CWPC * 00 * Front Gang Carrier Gang Assembly Disk Blade Bearing Wear Plate Front Scraper Assembly 00 Front Gang Carrier Complete Model BH0 Part Number Part Name 00 00 * 0 * CWPC * 00 * Front Gang Carrier Gang Assembly Disk Blade Gang Assembly Disk Blade Bearing Wear Plate Front Scraper Assembly 0 Front Gang Carrier Complete Model BH0 * See separate page for parts list.

Ref. Part Number Part Name 0 Rear Gang Carrier 0 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade CWPC * Heavy Duty Bearing Wear Plate 00 * Rear Scraper Assembly * See separate page for parts list. 0 Rear Gang Carrier, Complete Model BH0 Ref. Part Number Part Name 00 Rear Gang Carrier 0 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade CWPC * Heavy Duty Bearing Wear Plate 00 * Rear Scraper Assembly * See separate page for parts list. 0 Rear Gang Carrier, Complete Model BH0

Ref. Part Number Part Name 0 Rear Gang Carrier 0 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade CWPC * Heavy Duty Bearing Wear Plate 00 * Rear Scraper Assembly * See separate page for parts list. 0 Rear Gang Carrier, Complete Model BH0 Ref. Part Number Part Name 0 Rear Gang Carrier 00 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade CWPC * Heavy Duty Bearing Wear Plate 00 * Rear Scraper Assembly * See separate page for parts list. 0 Rear Gang Carrier, Complete Model BH00

Ref. Part Number Part Name 0 Rear Gang Carrier 00 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade CWPC * Heavy Duty Bearing Wear Plate 00 * Rear Scraper Assembly * See separate page for parts list. 0 Rear Gang Carrier, Complete Model BH0 Ref. Part Number Part Name 0 Rear Gang Carrier 0 * Gang Assembly Disk Blade 00 * Gang Assembly Disk Blade 0 * Gang Assembly Disk Blade CWPC * Heavy Duty Bearing Wear Plate 00 * Rear Scraper Assembly * See separate page for parts list. 00 Rear Gang Carrier, Complete Model BH0

Front Gang Carrier for Model Part Number Part Name BH0, BH0 B0000H Bushing, Pressed in BH0, BH00 B0000H Bushing, Pressed in BH0, BH0 B0000H Bushing, Pressed in Front Gang Carriers: 000 Model BH0, 00 Model BH0 Front Gang Carriers: 00 Model BH0, 00 Model BH00 Front Gang Carriers: 0 Model BH0, 00 Model BH0 Rear Gang Carrier Part Number Part Name For Model All BH Models B000H Bushing, Pressed in Rear Gang Carriers: 0 Model BH0, 00 Model BH0 Rear Gang Carriers: 0 Model BH0, 0 Model BH00 Rear Gang Carriers: 0 Model BH0, 0 Model BH0 0

Gang Assembly Requirements for Front Gang Carrier Model Part Number and Description BH0 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly BH0 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly BH0 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly BH00 00 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly BH0 00 Disk Blade Gang Assembly BH0 00 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly Gang Assembly Requirements for Rear Gang Carrier Model Part Number and Description BH0 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly BH0 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly BH0 BH00 BH0 BH0 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 00 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 00 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly 00 Disk Blade Gang Assembly 0 Disk Blade Gang Assembly Gang Assembly Requirements

Ref. 0 Part Number Part Name B0D * Bearing Assembly 000B Disk Blade, x., Notched 0B Disk Spacer CA Axle Washer C0B Bumper Washer N0 Axle Nut NLA Axle Nut Lock LW0 Lockwasher, / 00B Hex Bolt, / x / Gr. NC0 Hex Nut, / NC0J Hex Jam Nut, / BAX Axle, / x / FW0H Flatwasher, Hardened, / 000B Hex Bolt, / x Gr. * See separate page for parts list. 0 Gang Assembly Disk

Ref. 0 Part Number Part Name B0D * Bearing Assembly 000B Disk Blade, x., Notched 0B Disk Spacer CA Axle Washer C0B Bumper Washer N0 Axle Nut NLA Axle Nut Lock LW0 Lockwasher, / 00B Hex Bolt, / x / Gr. NC0 Hex Nut, / NC0J Hex Jam Nut, / BAX Axle, / x 0/ FW0H Flatwasher, Hardened, / 000B Hex Bolt, / x Gr. * See separate page for parts list. 0 Gang Assembly Disk

Ref. 0 Part Number Part Name B0D * Bearing Assembly 000B Disk Blade, x., Notched 0B Disk Spacer CA Axle Washer C0B Bumper Washer N0 Axle Nut NLA Axle Nut Lock LW0 Lockwasher, / 00B Hex Bolt, / x / Gr. NC0 Hex Nut, / NC0J Hex Jam Nut, / FW0H Flatwasher, Hardened, / 000B Hex Bolt, / x Gr. BAX Axle, / x / * See separate page for parts list. 0 Gang Assembly Disk

Ref. 0 Part Number Part Name B0D * Bearing Assembly 000B Disk Blade, x., Notched 0B Disk Spacer CA Axle Washer C0B Bumper Washer N0 Axle Nut NLA Axle Nut Lock LW0 Lockwasher, / 00B Hex Bolt, / x / Gr. NC0 Hex Nut, / NC0J Hex Jam Nut, / FW0H Flatwasher, Hardened, / 000B Hex Bolt, / x Gr. 0000B Disk Blade, Furrow Filler, 0 dia. BAX Axle, / x 0/ * See separate* page for parts list. 0 Gang Assembly Disk

Ref. 0 Part Number Part Name B0D * Bearing Assembly 000B Disk Blade, x., Notched 0B Disk Spacer CA Axle Washer C0B Bumper Washer N0 Axle Nut NLA Axle Nut Lock LW0 Lockwasher, / 00B Hex Bolt, / x / Gr. NC0 Hex Nut, / NC0J Hex Jam Nut, / FW0H Flatwasher, Hardened, / 000B Hex Bolt, / x Gr. 0000B Disk Blade, Furrow Filler, 0 dia. BAX Axle, / x / * See separate* page for parts list. 0 Gang Assembly Disk

Ref. 0 Part Number Part Name CC Concave Flange 0B Hex Bolt, / x / Gr. LW0 Lockwasher, / C Bearing Housing Cap C Shim Set CA Grease Seal C Cup C0 Cone B00 * Sleeve Assembly: B Sleeve (not serviced) B0000 Snap Ring Spacer (not serviced) C Snap Ring (not serviced) CA Bearing Housing AL0ZK Grease Fitting, / PP0 Pipe Plug, / CB Convex Flange * Components Not Serviced. Complete assembly must be replaced. B0D Tapered Roller Bearing Assembly 0

Number Required per BH Harrow Model Ref. Part Number CWPC 00 Part Name Heavy Duty Wear Plate Extra Heavy Duty Wear Plate BH0 BH0 0 0 BH0 BH00 BH0 BH0 CWPC Heavy Duty Bearing Wear Plate Standard 00 Extra Heavy Duty Bearing Wear Plate Optional Ref. Part Number Part Name 00 00 CFA CB0000 NC00 LW00 Scraper Blade, Front Scraper Blade, Rear Scraper Clamp Carriage Bolt, / x Hex Nut, / Lockwasher, / 00 00 00, 00 Front and Rear Scraper Assemblies

Number Required per Model Front and Rear Part 00 00 Part Name Front Scraper Assembly Rear Scraper Assembly BH0 BH0 BH0 BH00 0 BH0 BH0 Total Disk Scrapers Needed for BH Harrow Models Ref. Part Part Name Number C Axle Nut Wrench C0A Bag of Wrenches

Ref. Part Number Part Name 00A Front Stabilizer, end pin centers 00A Front Stabilizer, / end pin centers 00 Bushing, Bronze Shoulder B000H Bushing, Pressed in 00A Front Stabilizer, Models BH0 and BH0 00A Front Stabilizer, Models BH0 thru BH0 Ref. Part Number Part Name 00 Rear Stabilizer, / end pin centers 000 Rear Stabilizer, / end pin centers 00 Bushing, Bronze Shoulder 00 Bushing, Bronze Shoulder B000H Bushing, Pressed in 00 Rear Stabilizer, Models BH0 and BH0 000 Rear Stabilizer, Models BH0 thru BH0

Ref. Part Number Part Name 00 Front Pivot Hinge 000 Front Pivot Hinge 00 Bushing, Bronze Shoulder 00 Front Pivot Hinge, Models BH0 thru BH00 000, Front Pivot Hinge, Models BH0 and BH0 Ref. Part Number Part Name 00 Front Stabilizer Hinge 00 Front Stabilizer Hinge, All BH Models

Part Number Part Name TBX Jack Assembly Note: No Repair Parts Available. You must purchase the complete Jack Assembly. TBX Jack Assembly Ref. Part Number Part Name 00 Safety Chain 00 Chain Shackle 0 Safety Chain and Shackle Assembly

00 and 000 Latch Support Assemblies

Ref. 0 0 Part Number 0000 00 000 00 AG 00 00 RH0 000 00 00 0000B LW00 NC00 00 NC0S CK0 FW0 000 00 00 0B LW AL0ZK Part Name Latch Support Latch Support Latch Bar Latch Bar Klik Pin Pin Latch Collar Latch Pin Transport Lock Pin Support Beam Bushing, Bronze Hex Bolt, / x Gr. Lockwasher, / Hex Nut, / Pin Slotted Hex Nut, / Cotter Pin, x / Flatwasher, / Latch Pivot Bolting Bracket, Pivot Bushing Hex Bolt, / x / Gr. Lockwasher, / Grease Fitting, / 00 000 00 Latch Support Assembly Models BH0 and BH0 000 Latch Support Assembly Models BH0 thru BH0

Model BH0 BH0 BH0 BH00 BH0 BH0 Part Number 00A 00 * 000 * 00 * 00A * 00A 00 * 00 * 00 * 00A * 000A 00 * 000 * 00 * 00A * 00A * 000A 00 * 000 * 00 * 00A * 00A * 00A 00 * 00 * 00 * 00A * 000A 00 * 00 * 00 * 00A * Description Transport Group, Complete Tire and Wheel Assembly, ply Hydraulic Angle and Transport Control Leveling Group of Parts Transport Assembly, Single Transport Group, Complete Tire and Wheel Assembly, ply Hydraulic Angle and Transport Control Leveling Group of Parts Transport Assembly, Single Transport Group, Complete Tire and Wheel Assembly, ply Hydraulic Angle and Transport Control Leveling Group of Parts Transport Assembly, Single Transport Assembly, Dual Transport Group, Complete Tire and Wheel Assembly, ply Hydraulic Angle and Transport Control Leveling Group of Parts Transport Assembly, Single Transport Assembly, Dual Transport Group, Complete Tire and Wheel Assembly, ply Hydraulic Angle and Transport Control Leveling Group of Parts Transport Assembly, Dual Transport Group, Complete Tire and Wheel Assembly, ply Hydraulic Angle and Transport Control Leveling Group of Parts Transport Assembly, Dual * See separate page for parts list. Transport Assembly Requirements for BH Harrow Models

Ref. Part Number 00 00 * Part Name Transport Assembly, Single Hub and Spindle Assembly * See separate page for parts list. 00A Single Wheel Transport Assembly Models BH0 thru BH00 Ref. Part Number 0 00 * Part Name Transport Assembly, Dual Hub and Spindle Assembly * See separate page for parts list. 00A Dual Wheel Transport Assembly Models BH0 thru BH0

Ref. Part Number Part Name 000 Spindle 00 * Hub Assembly 00 ** Outer Cup 0000 ** Inner Cup NC00 Hex Nut, / 000B Hex Bolt, / x / Gr. NF00S Slotted Hex Nut, LW00 Lockwasher, / CK000 Cotter Key, / x FW00 Flatwasher, * See separate page for parts list. ** Part of 00 Hub Assembly. 00 Eight Bolt Hub Assembly 0

Ref. Part Number 00 00000 00 0000 0000 00 00 * 0000 * 000 * Part Name Hub Housing with Cups and Studs Dust Cap Outer Cone Grease Seal Inner Cone Lug Nut, / Outer Cup Inner Cup Stud ** Part of 00 Hub Housing. 00 Hub Assembly

Ref. Part Number 00 00 00 AW Part Name Tire,.L, Ply Tire,.L, Ply Wheel Valve Stem 00 Tire and Wheel Assembly Models BH0, BH0 and BH00 00 Tire and Wheel Assembly Models BH0, BH0 and BH0 Ref. Part Number AW LW00 NC00 Part Name Hose Mast Lockwasher, Hex Nut, AW0 Hydraulic Hose Holder

Ref. 0 Part Number Part Name 000 000 000 000 NCJ 000 0000B LW00 NC00 00 CK000 LW NC 0B Cylinder Anchor Pivot Bracket Spacer Stop Bolt, / x Hex Jam Nut, / Sleeve Hex Bolt, x Gr. Lockwasher, Hex Nut, Pin Cotter Key, / x Lockwasher, / Hex Nut, / Hex Bolt, / x / Gr. 00 Leveling Group

000 Hydraulic Angle and Transport Group

Ref. Part Number Part Name 0 0 0 0 0 H0J 000 000 000 H0J 000 00* AW0* TBX0 NC0 LW0 0 0000 000B 000 000 000B H0J0 000 00 00B LW0 000 00 CK000 00** 000 00* H0J 0000 000 000 000 00 000 00A 00B LW00 00 00 00B H0J 00 000B 000 000 00 0 000 000 Hose Ass y, Adapter, Straight Crossover Valve Adapter, 0 degree Hose Ass y Adapter, Straight Hydraulic Cylinder, x Hose Holder Hose Clamp Nut Lockwasher Transport Lock Hose Ass y Bolt Adapter, Restricting Tee Bolt Hose Ass y Adapter Cross Port Relief Valve Bolt Lockwasher Adapter Cylinder Pin Cotter Pin Hydraulic Quick Coupling Adapter, 0 degree Hydraulic Cylinder, / x Hose Ass y Hose Ass y Tee Hose Ass y Hose Ass y Clamp Hose Ass y Hydraulic Cylinder, x Bolt Lockwasher Cylinder Pin Transport Lock Bolt Hose Ass y Pin Bolt Adapter, 0 degree JIC Reducer Pressure Locking Valve Hose Ass y Adapter, Straight Tube Nut *See separate page for parts list. ** Not part of 000 Hydraulic Group. 000 Hydraulic Angle and Transport Group

00 Hydraulic Angle and Transport Group

Ref. Part Number Part Name 0 0 0 0 H0J 000 000 000 H0J 000 00* AW0* TBX0 NC0 LW0 00 0000 000B 000 000 000B H0J0 0000 00 00B LW0 000 00 CK000 000 00* H0J 0000 000 000 000 00 000 00A* 00B LW00 00 00 0B H0J0 00 000B 000 00 000 000 000 0 00** Hose Ass y Adapter, Straight Crossover Valve Adapter, 0 degree Hose Ass y Adapter, Straight Hydraulic Cylinder, x Hose Holder Hose Clamp Nut Lockwasher Transport Lock Hose Ass y Bolt Adapter, Restricting Tee Bolt Hose Ass y Adapter Cross Port Relieve Valve Bolt Lockwasher Adapter Cylinder Pin Cotter Pin Adapter, 0 degree Hydraulic Cylinder, / x Hose Ass y Hose Ass y Tee Hose Ass y Hose Ass y Clamp Hose Ass y Hydraulic Cylinder, x Bolt Lockwasher Cylinder Pin Transport Lock Bolt Hose Ass y Pin Bolt Adapter, 0 degree Pressure Locking Valve Adapter, Straight Tube Nut JIC Reducer Hose Ass y Hydraulic Quick Coupling *See separate page for parts list. ** Not part of 00 Hydraulic Group. 00 Hydraulic Angle and Transport Group

000 Hydraulic Angle and Transport Group

Ref. Part Number Part Name 0 0 0 0 0 H0J 000 000 000 H0J 000 00* AW0* TBX0 NC0 LW0 0 0000 000B 000 000 000B H0J0 0000 00 00B LW0 000 00 CK000 000 00* H0J 0000 000 0000 000 00 000 000A* 00B LW00 00 00 00B H0J0 00 000B 000 00* 00 00 000 000 000 000 0 00 00B Hose Ass y Adapter, Straight Crossover Valve Adapter, 0 degree Hose Ass y Adapter, 0 degree Hydraulic Cylinder, x Hose Holder Hose Clamp Nut Lockwasher Transport Lock Hose Ass y Bolt Adapter, Restricting Tee Bolt Hose Ass y Adapter Cross Port Relief Valve Bolt Lockwasher Adapter Cylinder Pin Cotter Pin Adapter, 0 degree Hydraulic Cylinder, x Hose Ass y Hose Ass y Tee Hose Ass y, / x Hose Ass y, / x Clamp Hose Ass y Hydraulic Cylinder, x Bolt Lockwasher Cylinder Pin Transport Lock Bolt Hose Ass y Pin Bolt Adapter, 0 degree Hydraulic Cylinder, / x Transport Lock Pressure Locking Valve Adapter, 0 degree Adapter, Straight Tube Nut JIC Reducer Hose Ass y Hydraulic Quick Coupling Bolt *See separate page for parts list. ** Not part of 000 Hydraulic Group. 000 Hydraulic Angle and Transport Group

00 Hydraulic Angle and Transport Group 0

Ref. 0 0 0 0 Part Number Part Name H0J Hose Ass y 000 Adapter, Straight 000 Crossover Valve 000 Adapter, 0 degree H0J Hose Ass y 000 Adapter, 0 degree 00* Hydraulic Cylinder, x AW0* Hose Holder TBX0 Hose Clamp NC0 Nut LW0 Lockwasher 0B Bolt 0 Transport Lock 0 Hose Ass y 000B Bolt 000 Adapter, Restricting 000 Tee 000B Bolt H0J0 Hose Ass y 0000 Adapter 00 Cross Port Relief Valve 00B Bolt LW0 Lockwasher 000 Adapter 00 Cylinder Pin CK000 Cotter Pin H0J Hose Ass y 000 Adapter, 0 degree 00* Hydraulic Cylinder, x H0J Hose Ass y 0000 Hose Ass y 000 Tee 000 Hose Ass y, / x 0000 Hose Ass y, / x 00 Clamp 000 Hose Ass y 000A* Hydraulic Cylinder, x 00B Bolt LW00 Lockwasher 00 Cylinder Pin 00 Transport Lock 00B Bolt H0J0 Hose Ass y 00 Pin 000B Bolt 000 Adapter, 0 degree 00 Pressure Locking Valve 000 Adapter, Straight 000 Tube Nut 000 JIC Reducer 0 Hose Ass y 00** Hydraulic Quick Coupling *See separate page for parts list. ** Not part of 00 Hydraulic Group. 00 Hydraulic Angle and Transport Group

00 Hydraulic Angle and Transport Group

Ref. 0 0 0 0 Part Number Part Name H0J Hose Ass y 000 Adapter, Straight 000 Crossover Valve 000 Adapter, 0 degree H0J Hose Ass y 000 Adapter, 0 degree 00* Hydraulic Cylinder, x AW0* Hose Holder TBX0 Hose Clamp NC0 Nut LW0 Lockwasher 0B Bolt 0 Transport Lock 0000 Hose Ass y 000B Bolt 000 Adapter, Restricting 000 Tee 000B Bolt H0J Hose Ass y 00 Adapter 00 Cross Port Relief Valve 00B Bolt LW0 Lockwasher 000 Adapter 00 Cylinder Pin CK000 Cotter Pin 000 Adapter, 0 degree 000 Adapter, 0 degree 00* Hydraulic Cylinder, x H0J Hose Ass y 0000 Hose Ass y 000 Tee H0J0 Hose Ass y 000 Hose Ass y 00 Clamp H0J0 Hose Ass y 000A* Hydraulic Cylinder, x 00B Bolt LW00 Lockwasher 00 Cylinder Pin 00 Transport Lock 00B Bolt H0J Hose Ass y 00 Pin 000B Bolt 000 Adapter, 0 degree 000 Adapter, 0 degree 00 Pressure Locking Valve 000 Adapter, Straight 000 Tube Nut 000 JIC Reducer 0 Hose Ass y 00** Hydraulic Quick Coupling *See separate page for parts list. ** Not part of 00 Hydraulic Group. 00 Hydraulic Angle and Transport Group

Ref. 0 Part Number Part Name AW0 * Hydraulic Hose Holder H0J0 Hose Assembly 0000 Adapter 00 Cross Port Relief Valve 00B Bolt LW0 Lockwasher 000 Hose Assembly 000B Bolt LW0 Lockwasher TBX0 Clamp 00A* Hydraulic Cylinder, x 000 Adapter, 0 degree 00B Bolt FW00 Flatwasher 00 Cylinder Pin 000 Hose Assembly 00 Hydraulic Quick Coupling *See separate page for parts list. ( For Models BH0 and BH0). 000 Hydraulic Angle Control Short Geometry

Ref. 0 Part Number Part Name AW0 * H0J0 0000 00 000B LW0 000 000B LW0 TBX0 000A* 000 00B FW00 00 000 00 Hydraulic Hose Holder Hose Assembly Adapter Cross Port Relief Valve Bolt Lockwasher Hose Assembly Bolt Lockwasher Clamp Hydraulic Cylinder, x Adapter, 0 degree Bolt Flatwasher Cylinder Pin Hose Assembly Hydraulic Quick Coupling *See separate page for parts list. ( For Models BH0 and up). 00 Hydraulic Angle Control Long Geometry

Ref. Part Number Part Name A A C A CD HPK * Tube Assembly Cylinder Rod, / Piston Rod Gland Cylinder Pin with () Clips, x / Seal Kit * HPK Seal Kit Sold as A Complete Kit Only. 00 Hydraulic Cylinder, x

Ref. 0 0 Part Number Part Name A0G0 * Piston Uni Ring A0 * Backup Ring A0 * O Ring A0 * O Ring A0 * Backup Ring A0000 * Loaded UCup A0U00 * Rod Wiper N000CAS Lock Nut PGAAMTSB Piston BAAAUTSQF Barrel Assembly RYAATSSQ Rod M0 Shipping Plug, Plastic D000 Set Screw, NT SH TCSAAESS Threaded Cap HTSABTSS Threaded Cap Head N00 Elastic Lock Nut CFAAAJSH Rod Clevis, Forged D00 Cap Screw, SH JYAAAHHU Clevis Pin D000 Cotter Pin 00 Seal Kit Sold as A Complete Kit Only. * Part of 00 Seal Kit. 00 Hydraulic Cylinder, / x

Ref. 0 Part Number Part Name HPKC Seal Kit Consists of: * # Wear Ring * # Expander Square * # Piston Seal * # O Ring * # Wear Ring * # O Ring * # BackUp Ring 000 Boss Plug, Steel * # UCup * # Cap Screw * # Canned Wiper CD0 Locknut CD0 Piston CD0 Shaft Assembly CD0 Case Assembly CD0 Head 000 Bushing # For Reference Only Seal Kit Sold as A Complete Kit Only. * Part of HPKC Seal Kit. 00 Hydraulic Cylinder, x

Ref. 0 Part Number N00 N0 N0 N0 N N CD0 CD000 CD00 CD Part Name Cylinder Tube, x / Piston Rod, / Piston Head Gland Stop Tube Bushing,. x. x. THD Locknut Grease Fitting, / Set Screw, / x x / Shipping Plug Ref. Only CD0 Seal Kit Sold as A Complete Kit. 00A Hydraulic Cylinder x

Ref. A B C D E F G H I J Part Number 00 00 00 00 00 000 0 00 00 00 000B LW0 FW0 Part Name DANGER Decal WARNING Decal CAUTION Decal ROME Decal Red Reflector Amber Reflector S.M.V. Decal Group Parts Book Holder Hose Clamp ATTENTION Decal Hex Bolt Lockwasher Flatwasher 0 Safety Decal Group

00 Light Group Assembly Optional

Ref. 0 Part Number Part Name 00 Straight Harness 00 Wishbone Harness 0 Light Bracket 000 Dual Lamp, LH 000 Dual Lamp, RH 00 Metal Wire Clamp LW0 Lockwasher NC0 Hex Nut 0B Hex Bolt 000B Hex Bolt 00B Hex Bolt NC0 Hex Nut LW0 Lockwasher 00B Hex Bolt 00 Light Group Assembly Optional Ref. Part Number Part Name 000 Hitch NC0 Hex Nut LW0 Lockwasher 00B Hex Bolt 00A Rear (Trail) Hitch Assembly Optional

Part Number AL0ZK 00 0000B LW00 NC00 0000B LW00 NC00 00 LW NF TBX NC0S CK0 FW0 00B 00 AL0ZK 000 000B 0000 Part Name Grease Fitting Pin Hex Bolt Lockwasher Hex Nut Hex Bolt Lockwasher Hex Nut Hex Bolt, Lockwasher Hex Nut. Tongue Jack Slotted Nut Cotter Pin Flatwasher Hex Bolt Pin Assembly Grease Fitting Wrench Hold Down Plate Hex Bolt Wing Nut Part Number AL0ZK 00 0000B LW00 NC00 00 0000B LW00 NC00 TBX 00 LW NF NC0S CK0 FW0 00B 00 AL0ZK 000 000B 0000 Part Name Grease Fitting Pin Hex Bolt Lockwasher Hex Nut Pin Hex Bolt Lockwasher Hex Nut Tongue Jack Hex Bolt, Lockwasher Hex Nut Slotted Nut Cotter Pin Flatwasher Hex Bolt Pin Assembly Grease Fitting Wrench Hold Down Plate Hex Bolt Wing Nut Models BH0 thru BH00 000 Group of Parts Models BH0 and BH0 00 Group of Parts

Assembly and Operating Instructions Table of Contents Table Of Contents. To The Owner Harrow Layout Exploded and Top View.. Introduction. Receiving Assembly / Instructions. Step. Assembling Gangs. Step. Installing Gangs on Gang Carriers.. Step. Joining and Adjusting Gang Carriers.. Step. Installing Stabilizer Assembly... Step. Installing Latch Support Assembly.. Step. Attaching Offset Bar Assembly Step. Installing Drawbar Assembly Step. Mounting and Adjusting Scrapers Step. Hydraulic Control Group Installation Lubrication.. Maintenance.. Serial Number Location Product Information Mount Wheels and Tires Recommended Spare Parts List. How To Order Parts.. Rome Warranties.. Page, 0, 0 0,,, 0,

TO THE OWNER Rome Plow Equipment Co.,LLC has made every effort to make your new BH Series Harrow dependable and reliable. In order to obtain the best use and value in the years to come, we urge you to read this Repair Parts and Assembling and Operating Instruction Manual very carefully. Keep it in a safe, handy place, for future reference and parts orders. Right and left sides are determined by standing at the rear of the harrow and facing the direction of travel. IMPORTANT BE SURE TO SPECIFY SERIAL NUMBER WHEN ORDERING PARTS. Model Number Serial Number Dealer.. Date of Purchase

Illustration. Exploded View Main Components of a Typical BH Model Harrow

Illustration A. Top View of a Typical BH Model Harrow

Introduction The Rome HingeWheel Combination Harrows are designed for long troublefree operation under rigorous conditions. These harrows combine the superior uniform leveling and mixing capability of the hinge harrow with the transportability of the wheel harrow. A full range of adjustments allow the operator to control depth of penetration. Gang angle of adjustments are from 0 to degrees and can be made on the go with hydraulic control. Tapered roller bearings are greaseable to assure long life with minimal down time and increased productivity. Heavy duty bearing wear plates are standard. If soil conditions are extremely abrasive, an Optional, Extra Heavy Duty Bearing Wear Plate, may be ordered. Receiving Check all parts on the Packing List. See various illustrations and layout for assembly. Assembly For export shipments: Follow steps through. For domestic shipments: Follow steps through. Step Assembling Gangs Mount disk blades on each axle assembly as shown in Illustration. The number of disk blades and disk spacers will vary with each size disk gang assembly. For shipping purposes, the bearings, spacers, axle washer, bumper washer, bumper washer nuts and axle nut locks are preassembled. Disk blades are shipped bundled together. To assemble the gangs, perform the following steps: ) Remove the axle nut on the bumper washer end of the shipping assembly. The bumper washer fits the convex surface of the disk blade. ) Remove all bearings and spacers from the axle; leaving only the axle washer, an axle nut lock and one axle nut on the axle. Caution: Care should be taken to prevent damage to the axle threads as parts are slid on the axle. ) Slide a disk blade down the axle until it contacts the axle washer. Note: The axle washer fits the concave side of the blade. Slide a bearing on the axle and raise the axle to a to a vertical position. Axle, blade and bearing will now stand in an upright position without being held. If axle washer is not snug against the concave side of the blade, it is necessary to tilt axle and disk blade and slide a short x block of wood underneath the disk blade. Be sure to position it between the nut and floor or ground. This assures that the threaded end of the axle will be visible when the gang is completely stacked. Note: If this procedure is not followed, the shaft will be too short and the nut cannot be installed.

Step Assembling Gangs... continued ) Refer to Illustration and continue to slide the bearings, disks and spacers down the the axle exactly in the order shown. Important: Make sure that the concave and convex faces on the bearing assemblies, washers and disk spacers coincide with the faces on the disk blades. Note: Concave and convex flanges on the bearing assemblies are factory mounted to correspond to the front and rear gangs in order to have the grease fittings always facing to the rear. Illustration. Assembling Gangs ) After the last disk blade is in place, mount the axle washer onto axle. Replace the axle nut. Now using the axle nut wenches provided, tighten axle nuts as much as possible. For best results and additional leverage, place a to foot length of diameter pipe on each axle nut wrench to serve as an extension to the handles. Important: Retighten axle nuts after the first 0 to hours of operation. After to 0 hours of operation, retighten again! Now mount nut locks to axle washers and bumper washers with cap screws provided. Step Installing Gangs on Gang Carriers Where lifting facilities are available: ) Position front gang assemblies with concave side of disks to the right, as viewed from the rear. ) Position rear gang assemblies with concave side of disks to theleft, as viewed from the rear. ) Place gang carriers on corresponding gang assemblies and attach with bearing bolts. Where lifting facilities are limited: ) Position gang carriers upside and place gang assemblies on gang carriers and attach with bearing bolts. ) Turn completed assemblies of gangs and gang carriers right side up. 0

Step Joining Gang Carriers Secure the rear gang carriers in the upright position by blocking up under the hitch plates and gang carrier. Attach pivot hinge at the hinge point with the hinge pin. Roll front gang carrier into position and bolt pivot hinge to front gang carrier with x bolts. (See Illustration.) For operation in most soil conditions, it is recommended that the pivot hinge be bolted approximately in the center of the front carrier plate. Do Not Tighten at this time! Adjusting Rear Gang Carriers: The rear gang carrier may be shifted laterally in relation to the front gang carrier to obtain better leveling and filling of the left hand furrow. To accomplish this, place the harrow at a half angle position and block the rear gang. ) Remove the nine bolts attaching the pivot hinge (Illustration ). If the rear gang carrier is to be shifted to the left, reverse the tractor very slowly until the selected bolt holes on the front gang carrier plate are reached. If the rear gang carrier is to be shifted to the right, move the tractor forward slowly. Replace the bolts. Illustration. Joining Gang Carriers

Adjusting Rear Gang Carriers... continued: ) Remove the six bolts attaching the stabilizer hinge (Illustration ), and swing into position corresponding to that of the pivot hinge. This means the last bolt in the pivot hinge is in the third hole from the left end of the front gang carrier bolting plate, the last bolt on the left end of the stabilizer hinge should also in the third hole from the left end of its bolting plate. Step Installing Stabilizer Attach rear stabilizer to rear gang carrier and stabilizer pivot to front stabilizer with the pin provided. Swing stabilizer with stabilizer hinge over right plate on front gang carrier. Bolt into position with x bolts provided to coincide with position of pivot hinge (Illustration ). Pivot hinge and stabilizer hinge should be bolted in the same relative position on front gang carrier bolting plates. Do Not Tighten. Illustration. Stabilizer Assembly

Step Installing Latch Support Assembly The latch support assembly is standard equipment and will work alone or in conjunction with the hydraulic control group. Its function is to maintain the angle between the front and rear gangs when the harrow is in operation and to hold the gangs parallel and to support the front gang during transport. Assembly and Operation: ) Attach the latch support beam to the rear gang carrier with the pin provided. (Refer to Illustration, A and B). ) Attach the opposite end (front) of the latch support beam to the wide end of the latch support with pin. ) A pin with a handle and a klik pin are provided to hold the harrow closed during transport. There are two holes in the latch support for this pin. During the transport (with harrow closed) this pin is placed in the front hole on the latch support assembly. The other hole (on the back side of the latch support) is for storing the pin while the harrow is in operation. Illustration. Latch Support Assembly

Step Attaching Offset Bar Assembly Bolt the offset bar to the hitch plates on the front gang carrier with bolts and bushings provided in the offset bar. (See Illustration ). The hitch plates are provided with three holes. For normal operation in average soil conditions, bolt the offset bar to the center holes; for hard soil and deepest penetration, use upper holes. For light soil and lesser penetration, bolt to the lower holes. Attaching Offset Bat to Hitch Brackets Step Attaching and Adjusting Drawbar Assembly The drawbar is attached to the offset bar with three bolts, nuts and lockwashers. The harrow may be moved laterally behind the tractor by moving the drawbar on the offset bar. For normal operation, the drawbar plates should be bolted near the center of the offset bar. To make major or large offsets, the drawbar plates should be moved on the offset bar. To make minor or small offsets, remove the drawbar positioning bolt, loosen the drawbar pivot bolt and move the drawbar between the plates to the desired position and secure. When properly adjusted, there will be no side draft and the drawbar should be in the approximate line of travel. The trial adjustments should be made after the harrow has been put into operation, observing the proper angle and trailing of the harrow. Attaching and Adjusting the Drawbar

Step Mounting and Adjusting Scraper Assembly Install the scrapers as shown in Illustration. The scraper should be adjusted so that it does not come in contact with the disk blade as it turns. It should be slightly closer at the point so that trash buildup between the scraper and the disk blade is minimal. Illustration. Scraper Installation Step Hydraulic Control Group Installation Four hydraulic cylinders in the hydraulic system are used to control the adjustments to the harrow necessary under different conditions. Two of these (connecting transport to rear frame) are used to raise or lower the transport arms and bring the harrow into transport or working position. These cylinders must extend to lower the transport arms, which will bring the harrow into the transport position, pressing the tires (mounted on transport arms) against the ground and gradually lifting the frame. Retracting the cylinders will lower the frame until the disks rest on the ground. These two cylinders must be fully retracted during working conditions. Note: Do Not Lower the Transport Assembly when the Harrow Angle is Open! The function of the small cylinder (connecting the front frame to the leveler) is to level the harrow relative to the height of the tractor drawbar during transport. Use the adjusting bolt to stop the cylinder pivot (with fully extended cylinder rod) in a position to allow it to reach tractor drawbar with the plunger when the harrow is lifted up and the frame is parallel with ground level. When the bolt is adjusted to the height of the tractor, it must be blocked by tightening the nut on the rear side of the bracket. The system is designed in such a way (using different tractors) that the stop must be adjusted only once. If the harrow is in the working position with the cylinder rod fully retracted, there will always be enough free movement for the cylinder pivot to guarantee good floatation of the harrow. (See Illustration on page and Illustration A on page for assembly). See Hydraulic Control Group Installation, Illustration, on page.

Step Hydraulic Control Group Installation... continued Hydraulic Control Group Assembly A fourth hydraulic cylinder is installed from the rear gang carrier (base end) to the rear stabilizer (rod end) and is used to open or close the angle between the front and rear gangs. Before this can be done, the crossover valve must be manually activated to direct the fluid to the angling hydraulic cylinder. Note: Do Not Open the Harrow with the Wheels Supporting its Weight! To transport the harrow, reverse the manual crossover valve to direct the fluid to the transport and leveling hydraulic cylinders. (See Illustration above for assembly details). Note: If hydraulic angling control is for some reason, used without transport assembly, disregard instructions for the cylinders and valve used with them.

Lubrication There are lubrication fittings at all harrow hinge points. These should be greased as necessary. See following instructions for lubrication of the tapered roller gang bearing assembly. Tapered Roller Gang Bearing Assembly Lubrication: Use a medium consistency pressure grease. Grease the bearings whenever the seals appear dry. Add sufficient grease to force lubricant out under the seal lip. In sandy conditions, the bearings should be lubricated daily to prevent the buildup of sand and grease just outside the sealing surface. Rome tapered roller bearing assemblies are equipped with seals facing outward; therefore no damage can occur due to excessive lubrication. Adjustment: Check the bearings every 00 to 00 hours for proper adjustment. If end play is detected, remove shims from under the bearing cap to eliminate it. However, if too many shims are removed, the bearing will run tight. This is undesirable and will result in accelerated wear of the bearing rollers and races. Caution: The neoprene seals should be watched closely for wear. These seals should last for 000 to00 hours of use. When they become worn, they must be replaced. The successful operation of the bearing depends on keeping it dirt free. Maintenance All nuts and bolts must be kept tight. Special attention must be given to keeping axle nuts tight. Note: Tighten Axle Nuts Again After First 0 to hours of Operation. Then After to 0 Hours of Operation, Tighten Once Again. If these nuts are not kept tight, disks will turn on the axle and all components of the gang will be damaged! Serial Number Location The serial number can be found on the rear gang carrier. Be sure to specify serial number when ordering parts.

Important Information The Eight Bolt Hub has a load rating of 000 lbs. when mounting with a.0 negative offset. The wheel is mounted correctly when the valve stem and the deep dish of the wheel are both facing out and on the lug bolt side of the wheel. WARNING: Reversing the wheels will change the position in which the load is carried on the hub bearing and will reduce bearing life. Always make sure to torque wheel bolts at 0 to 00 ft. lbs. Mount Wheels and Tires Attach wheel and tire assemblies to the hub. Assemblies with lug bolts. Be sure the valve Stem faces to the outside (lug bolt side).

Recommended Spare Parts List BH0, BH0, BH0, BH00, BH0, BH0 Number Required per Model Part Number RR0B RHC RH0A SP0000 B0D CA C C0 C CA B00 C BAX BAX BAX BAX BAX N0 NLA CA C0B 00 00 00 0000 0000 00000 00 00 0B 000B 0000B B000H B000H 00 HPK 00 HPK CD0 CD0 Part Name Hitch Clevis Plunger Plunger Collar Plunger Collar Pin Tapered Bearing (Complete) Bearing Housing Bearing Housing Cap Bearing Cone Bearing Cup Grease Seal Sleeve Assembly Shim Set Axle Axle Axle Axle Axle Axle Nut Axle Nut Lock Axle Washer Bumper Washer Hub (Complete) Hub with Cups and Studs Outer Bearing Cone Inner Bearing Cone Grease Seal Dust Cap Front Scraper (Complete) Rear Scraper (Complete) Spacer x. Disk Blades (Notched) 0 Furrow Filler Disk Blade Bushing Bushing Bushing, Bronze Packing Kit ( x Cylinder) Packing Kit (/ x Cylinder) Packing Kit ( x Cylinder) Packing Kit ( x Cylinder) Packing Kit ( x Cylinder) BH0 BH0 BH0 BH00 0 0 BH0 BH0 0

HOW TO ORDER PARTS Please be sure to furnish the quantity, part number and name of each part wanted. It is also important to give the Serial Number of the machine for which the parts are intended. It is also suggested that the Serial Number of the machine be written in the space below so that it will be readily available when you need it. THIS PARTS BOOK IS FOR MACHINE SERIAL NUMBER Serial Number To insure prompt delivery, please furnish the correct name of the consignee, as well as the street address, town, country, state and zip code to which the parts are to be shipped and indicate whether shipment is to be by truck, UPS, air courier or by other means. ONLY ROME PARTS GIVE ROME PERFORMANCE The same quality and craftsmanship that have made Rome products famous throughout the world are built into all Rome Replacement parts. ROME PLOW EQUIPMENT CO.,LLC Sixth Street, P.O. Box Telephone: (0) 0 Cedartown, Ga. 0, USA Fax: 0 web site: www.romeplow.com email: sarrington.com

ROME AGRICULTURAL/CONSTRUCTION PRODUCTS WARRANTY Rome Plow Equipment Co.,LLC P.O. Box Cedartown, Georgia 0 USA () WHAT IS COVERED BY THIS WARRANTY: Rome Plow Equipment Co.,LLC, hereafter referred to as Rome, warrants, to the original retail purchaser only, or placed in the dealers rental fleet, that all equipment, parts and accessories which it manufactures are free from defects in material or workmanship under normal agricultural/construction use, service, proper setup and adjustment. The duration of this warranty is one () year from date of delivery to original purchaser. If the equipment is used in a construction application, the warranty is six () months. This warranty is limited to the repair or replacement of part or parts to the original purchaser, found by the manufacturer, through the authorized selling dealer, to be defective in material or workmanship in the warranty period. Labor for authorized repairs are covered at dealer registered labor rate based on Rome s published flat rate. Rome reserves the right to have defective parts returned to Rome Plow Equipment Co.,LLC. at Sixth Street, Cedartown, GA 0, prepaid by the dealer or purchaser and accompanied by a completed Warranty Return Authorization Number. Rome shall complete such repair or replacement within a reasonable time after Rome receives the product. Rome may, at its option, authorize its representatives to make adjustments in the field. Consult your dealer before removing any parts or making repairs. For warranty claim, notify the selling dealer. () WHAT IS NOT COVERED BY THIS WARRANTY: Rome, does not warranty: (a) any product component or parts not manufactured by Rome (including, but not limited to tires), (b) repairs made by unauthorized persons, (c) damage caused by use for purposes other than those for which it was designed, (d) damage caused by disasters such as fire, flood, wind, and lightning, (e) damages caused by neglect, abuse, abnormal use, improper or unreasonable use, accident or misuse, (f) damages caused by unauthorized attachments, alterations, or modifications, (g) damages caused by improper service, setup or adjustments, (h) Rome equipment which has had the serial numbers removed or made illegible, (i) normal wear, (j) transportation to and from authorized dealer=s place of business or Rome, (k) dealer travel hours, (l) mileage, (m) labor for unauthorized repairs. () DISCLAIMER OF WARRANTY: The foregoing warranties are in lieu of all other warranties of merchantability and fitness for a particular purpose. Any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of this limited warranty. This warranty gives you specific legal rights and you may have other rights which vary from state to state. () LIMITATION OF REMEDIES: In no case shall Rome be liable for any special, incidental, or consequential damages based on breach of warranty, breach of contract, negligence, strict liability in tort, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of savings and revenue, loss of use of the equipment, or any associated equipment, cost of capital, cost of any substitute equipment, facilities, or services, downtime, the claims of third parties and injury to property. Some states do not allow limitations or incidental of consequential damages, so the above may not apply to you. () NO OTHER WARRANTIES: Unless modified in writing, signed by both parties and approved by the General Manager of Rome, this agreement is understood to be the complete and exclusive agreement between the parties, superseding all prior agreements, oral or written, and all other communications between the parties relating to the subject matter of this agreement. No employee of Rome or any other party is authorized to make any warranty in addition to those made in this agreement. () Rome reserves the right to improve products through modifications and changes in design or material without being obligated to incorporate such changes in products of prior manufacture.

AGRICULTURAL/CONSTRUCTION REPAIR PARTS WARRANTY Rome Plow Equipment Co.,LLC P.O. Box Cedartown, Georgia 0 USA () WHAT IS COVERED BY THIS WARRANTY: Rome Plow Equipment Co.,LLC, hereafter referred to as Rome, warrants, to the original retail purchaser only, or placed in the dealers rental fleet, that all parts and accessories which it manufactures are free from defects in material or workmanship under normal agricultural/construction use, service, proper setup and adjustment. The duration of this warranty is ninety (0) days from date of delivery to original purchaser. This warranty is limited to the repair or replacement of part or parts to the original purchaser, found by the manufacturer, through the authorized selling dealer, to be defective in material or workmanship in the warranty period. Rome reserves the right to have defective parts returned to Rome Plow Equipment Co.,LLC at Sixth Street, Cedartown, GA 0, prepaid by the dealer or purchaser and accompanied by a completed Warranty Return Authorization Number. Rome shall complete such repair or replacement within a reasonable time after Rome receives the product. Rome may, at its option, authorize its representatives to make adjustments in the field. Consult your dealer before removing any parts or making repairs. For warranty claim, notify the selling dealer. () WHAT IS NOT COVERED BY THIS WARRANTY: Rome, does not warranty: (a) any product component or parts not manufactured by Rome (including, but not limited to tires), (b) repairs made by unauthorized persons, (c) damage caused by use for purposes other than those for which it was designed, (d) damage caused by disasters such as fire, flood, wind, and lightning, (e) damages caused by neglect, abuse, abnormal use, improper or unreasonable use, accident or misuse, (f) damages caused by unauthorized attachments, alterations, or modifications, (g) damages caused by improper service, setup or adjustments, (h) normal wear, (I) transportation to and from authorized dealer s place of business or Rome, (j) dealer travel hours, (k) mileage, (l) labor for unauthorized repairs. () DISCLAIMER OF WARRANTY: The foregoing warranties are in lieu of all other warranties of merchantability and fitness for a particular purpose. Any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of this limited warranty. This warranty gives you specific legal rights and you may have other rights which vary from state to state. () LIMITATION OF REMEDIES: In no case shall Rome be liable for any special, incidental, or consequential damages based on breach of warranty, breach of contract, negligence, strict liability in tort, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of savings and revenue, loss of use of the equipment, or any associated equipment, cost of capital, cost of any substitute equipment, facilities, or services, downtime, the claims of third parties and injury to property. Some states do not allow limitations or incidental of consequential damages, so the above may not apply to you. () NO OTHER WARRANTIES: Unless modified in writing, signed by both parties and approved by the General Manager of Rome, this agreement is understood to be the complete and exclusive agreement between the parties, superseding all prior agreements, oral or written, and all other communications between the parties relating to the subject matter of this agreement. No employee of Rome or any other party is authorized to make any warranty in addition to those made in this agreement. () Rome reserves the right to improve products through modifications and changes in design or material without being obligated to incorporate such changes in products of prior manufacture.