Specification sheet of T8 LED Tube Brief Introduction Special designed lockable 90-180 degree rotating end caps Lighting efficiency up to 100-110lm/W, Saves up to 70% Energy, Good a l t e rn at i ve to replace traditional fluorescent tubes. Just replace fluorescent tube starter with BES LED starter bef ore replacement. Advantages 1. Lockable 0-180 rotating end caps 2. Lifespan:>50,000hrs 3. Saves up to 70% Energy, Lighting efficiency up to 100-110lm/W 4. All LED tube s are qualified with TUV,SAA,CB,C -Tick Certificates TUV/CE/RoHS/CB/ SAA/C -Tick Features 5 Years W a rra n t y. Light Source: Ever Light SMD 3528 Single End Power Wiring -Safe Application Material: AL + Strong PC cover Easy Installation: BES LED tubes fit well into conventional T8 fluorescent fittings. More features are as follows. Extended Life The ballast c a n b e bypassed or removed completely No Buzzing Environmentally friendly and with no Mercury No Radio Frequency Interference No Flickering Fast Return on Investment
Application Hotels Conference rooms / meeting rooms Factories / Offices Commercial Properties Residential dwellings Schools, colleges and universities Hospitals Supermarkets Warehouses Railway Stations Airports Dimension (Unit: mm) 588
Technical Specification A: Technical Parameter Item BES.T8.03.06.01 BES.T8.03.09.01 BES.T8.03.12.01 BES.T8.03.15.01 Dimension 588x 26mm 895x 26mm 1198x 26mm 1498x 26mm (2FT) (3FT) (4FT) (5FT) Voltage AC85V - 265V 50/ 60HZ Power 10W 14W 20W 24W LED Type SMD 3014 LED Quantity 96pcs 132pcs 192pcs 240pcs Lumen (±10%) 1000lm 1400lm 2000lm 2400lm Colour Temperature (CCT) 2800-3500K, 4000-4500K, 5500-6500K Beam Angle 140-180 Color Rendering Index (CRI) Ra >80 Power Supply Efficiency >90% LED Luminous Efficiency Up to 100lm/W Power Factor (PF) >0.95 Total Harmonic Distortion(THD) 15% IP Rating IP 50 Certificate CB,C-TICK,SAA,TUV B: Mechanical S p e c i f i c a t i o n s LED Transformer Type End Cap Type Pin Type Material Optional Cover Isolated LED Transformer 180 degree lockable Rotatable End Cap T8-G13 Aluminum housing, PC cover Clear & Frosted Cover C. Environmental Temperat ure Range Operating -20 to 40 Humidity Range Operating 10% to 80% Temperat ure Range Storage -40 to 65 Humidity Range Storage 10% to 80%
Plane Isolux Curve& Illumination Cone Curve A: 60cm, 10W, BES.T8.03.06.01, 6000K, Frosted Cover B: 90cm, 14W, BES.T8.03.09.01, 6000K, Frosted Cover
C: 120cm, 20W, BES.T8.03.12.01, 6000K, Clear Cover D: 150cm, 24W, BES.T8.03.15.01, 6000K, Clear Co ver
Installation Installation Guide for Single-end Input LED Tube 1. Inductive Fixture (Magnetic Ballast) Starter A: Traditional fluorescent tube with inductive fixture. (Magnetic Ballast) L N AC110V/220V Ballast Way 1: Replace with Remove LED starter Starter Way2: Remove Starter L N AC100V-254V ballast L N Add wire AC100V/240V Ballast Remove Turn off the power, remove fluorescent tube remove fluorescent starter and replace with LED starter. Place LED tube into position. Turn off the power, remove fluorescent tube and fluorescent starter. Bypass magnetic ballast (Qualified Electrician ONLY). Replace with LED tube. 2.Electronic Fixture (Electronic Ballast) Way 1: ballast Ballast Remove AC110V-220V L N AC100V-240V L N Add link Add link B: Traditional fluorescent tube with electronic fixture. (Electronic Ballast) Turn off the power, remove fluorescent tube. Qualified Electrician needs to bypass or remove the electronic ballast, reconnect for single ended power input, and then replace with LED tube. Warning: Please use the product within the specified range of voltage Please follow the correct installation steps to install the product, and Do Not touch the tube when it is working. Please cut the power off when install and remove the products to avoid risk of electric shock. Do not look directly at LED light source for long p e r i o d s of time Ensure Electronic components are not exposed to rain or other liquids. If any Lamps release gas, abnormal sound or unusual flashes, this means the shell has been broken and should be removed under controlled measures.
Compliance and Standards 1. Insulation Resistance The IR shall be at least 50MΩ when apply 500Vdc between primary and secondary 2. Dielectric Strength (Hi-pot) Input to Output 3750Vac 60Hz 1minute 3MA. When the AC voltage of 3.75KV is applied, and the voltage applied to the insulation under test it is gradually raised from zero to the prescribed voltage in 1s, and held at that value for 60s between the inputs and output and between the input and housing, the current sensitivity shall be less than 5mA. After this test, the adapter shall exhibit no electrical and mechanical abnormalities. 3. Leakage Current The leakage current shall be less than 0.25m A for class II when power supply is operated maximum voltage and maximum load. 4. Safety Standard 34A - 1501NP IEC: 60598-1:2008 IEC61347-1/A1:2010 IEC61347-2-13:2006 IEC62031:2008 IEC62471:2006 IEC62471-2:2009: Passed EN60598-1/A 11:2009 EN61347-2-13:2006 EN61347-1/A1:2011 EN62031:2008 EN62471:2008 EN61195:1999 E N 6 2 4 9 3 : 2 0 1 0 : Passed 5. EMI/EMS Standard EN55015: Passed EN61000-3 - 2: Passed EN61000-4- 2: Passed 6. Certificates TUV/CE/RoHS/CB/ SAA/C-Tick Packaging A: Packaging I n f o r ma t i o n LED Tube Single Box Packing Carton Package Length QTY Size mm G.W. Volume QTY Size(mm) G.W. Volume Weight Weight 60cm 1pc 34*38*630 0.33kg 0.57 kg 25 pcs 495*218*220 9.0kg 4.74kg 90cm 1pc 34*38*930 0.45kg 0.84 kg 25 pcs 945*218*220 12.0kg 9.06 kg 120cm 1pc 34*38*1230 0.58kg 1.12 kg 25 pcs 1245*218*220 15.0kg 11.94 kg 150cm 1pc 34*38*1530 0.70kg 1.39 kg 25 pcs 1545*218*220 20.0kg 14.82 kg
B: Packaging Images Warranty A 5-year warranty from the date of purchase is offered for BES LED panels. Under the terms of this warranty, if the product has a failure occurring under normal usage within the warranty period, BES will provide a free maintenance service based on the proof of documents and the invoice (copy) along with the failed product. BES will provide maintenance at a fee if it falls under the below conditions set out within the warranty. Failure or damage due to force or misuse. Failure or damage due to transportation or unloading. Failure or damage due to incorrect usage or failing to comply with the User's Guide and Cautions. Failure or damage due to demolition, repair, alteration without the Manufacturer's authorization. Please deliver the failed product within the original packing to qualify for the free maintenance service; BES will not be responsible for any failure or damage in transportation if the customer uses the non-original packaging or improper packaging. BES reserves the rights for final explanation of aforesaid terms. Caution: BES will not be responsible for any other failure or damage caused by incorrect usage. Remarks: For more information please consult BES by mail: sales@brightenergysolutions.co.uk Or call the BES sales team on 0203 397 8785