TESTO ITC KORINNA 28mm Allargato SECTIONAL DIRECTIONAL CONTROL VALVES

ESO IC KORINN 8mm llargato SECIONL DIRECIONL CONROL VLVES

SD6 - DLS7 SD6 Simple, compact and heavy duty designed sectional valve from to sections for open and closed center hydraulic systems. H Fitted with a main pressure relief valve and a load check valve on every working section H vailable with parallel, tandem or series circuit. H Optional power beyond port. H wide variety of port and circuit valves. H vailable manual, pneumatic, hydraulic, electro--hydraulic, and remote with flexible cables spool control kits. H Diameter 6 mm (.63 in) interchangeable spools. DLS7 hey are for systems with fixed displacement pumps (open center version), or variable displacement pumps (closed center version), with Load--Sensing signal on each working section to pump flow control valve control. H Load--indipendent flow control. H orts valves and side control kits are the same of SD6 directional valve. H L.S. signal connections on every working section. dditional information his catalogue shows the product in the most standard configurations. lease contact Sales Dpt. for more detailed information or special request. WRNING! ll specifications of this catalogue refer to the standard product at this date. Walvoil, oriented to a continuous improvement, reserves the right to discontinue, modify or revise the specifications, without notice. WLVOIL IS NO RESONSILE FOR NY DMGE CUSED Y N INCORREC USE OF HE RODUC. nd edition December 6: his edition supercedes all prior documents. DU

SD6 - DLS7 Content Working conditions... 4 SD6 directional valve... 7 DLS7 Load Sensing directional valve... 73 Installation and maintenance... 94 ccessories... 98 DU 3

SD6 - DLS7 Working conditions his catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm /s -- 46 cst viscosity at 4 C temperature. SD6 Nominal flow rating 45 l/min US gpm Operating pressure (max.) parallel or tandem circuit 35 bar 46 psi series circuit bar 35 psi ack pressure (max.) on outlet port 5 bar 36 psi Internal leakage () p= bar - 45 psi fluid and valve at 4 C 3cm 3 /min *.8 in 3 /min * DLS7 Nominal flow rating (with 4 on inlet port 75 l/min US gpm bar / psi stand--by) on ports and 6 l/min 6 US gpm Operating pressure (max.) 35 bar 46 psi ack pressure (max.) on outlet port 5 bar 36 psi Internal leakage () p= bar - 45 psi fluid and valve at 4 C 3cm 3 /min *.8 in 3 /min * Fluid Mineral based oil Fluid temperature with NR (UN -N) seals from -- to 8 C from -4 to 76 F with FM (VION) seals from -- to C from -4 to F Viscosity operating range from 5 to 75 mm /s from 5 to 75 cst min. mm /s cst max. 4 mm /s 4 cst Max level of contamination --/9/6 -- ISO 446 NS 638 - class with mechanical devices from --4 to 6 C from -4 to 4 F mbient temperature with pneumatic and hydraulic devices from --3 to 6 C from - to 4 F ie rods tightening torque (wrench 3) NOE (*) - Except differently specified inside the catalog. NOE - For different conditions please contact Sales Dept. with electric devices from -- to 5 C from -4 to F 3 Nm lbft 4 DU

SD6 - DLS7 Standard threads REFERENCE SNDRD S UN -UNF MERIC NF HRED ISO 8/ ISO 63 ISO 6 NSI..3 CCORDING O S 779 NSI. unified CVIY DIMENSION CCORDING O ISO 79 96 9974-- SE J96 J44 J476a DIN 385-- shape X or Y 385-- shape X or Y ORS HREDING SD6 ORS S UN -UNF MERIC Inlet G3/8 3/4--6 (SE 8) M8x.5 Working ports and G3/8 9/6--8 (SE 6) M8x.5 Outlet and carry--over C G/ 3/4--6 (SE 8) Mx.5 ILO ORS Hydraulic ports G/4 9/6--8 (SE 6) G/4 neumatic ports NF /8--7 NF /8--7 NF /8--7 DLS7 ORS S UN -UNF Inlet and outlet G/ 3/4--6 (SE 8) Working ports and G3/8 9/6--8 (SE 6) Load Sensing signal LS G/4 9/6--8 (SE 6) ILO ORS Hydraulic ports G/4 9/6--8 (SE 6) neumatic ports NF /8--7 NF /8--7 DU 5

SD6 - DLS7 6 DU

SD6 Content Content Dimensional data... 8 Hydraulic circuit... 9 erformance data... Ordering codes... Inlet cover ordering codes... 4 dimensional data and hydraulic circuit... 5 inlet relief options... 6 inlet valve options... 7 R commutator configuration... 9 S flow regulator configuration... Working section ordering codes... dimensional data and hydraulic circuit... 4 spools... 5 side spool positioners... 3 side options... 49 complete controls... 54 port valves... 59 Intermediate section CS mid return manifold section... 64 DFG compensated flow divider section... 65 EI service relief valve section... 66 EV9 compensated flow control section... 67 EV3 inlet section with regulated flow... 68 Outlet cover ordering codes... 7 dimensional data and hydraulic circuit... 7 DU 7

SD6 Dimensional data (series or tandem circuit) E F 9 9.4.4 3.8 ower beyond configuration WLVOIL 6 9 MDE IN ILY 9.35 3.8 roduction batch : 6 = production year (6) = progressive number Valve code 87 3.43 96.5 7.74 8 3.5 4.7.5 7.89 4.57 6.5.46 7.5.69 M8 9 36.5.44 WLVOIL 6 MDE IN ILY 4.57 3.79 M8,5 3.85.8 4.5 38 38 4.59.5.5.57 95.5.47 3.76 Fixing bracket available on request 4 YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb SD6/ 8.5 4.66 58.8 5.3.7 SD6/7 346.5 3.65 86.6 9.4 4.8 SD6/ 56.5 6.6 96 3.78 7.6 6.6 SD6/8 384.5 5.5 34.76.7 47.9 SD6/3 94.5 7.66 34 5.8 9.9.8 SD6/9 4.5 6.65 36 4.6 4 53 SD6/4 3.5 9.5 7 6.77. 6.9 SD6/ 46.5 8.5 4 5.76 6.3 58. SD6/5 7.5.65 8.7 4.8 3.6 SD6/ 498.5 9.65 438 7.6 8.6 63. SD6/6 38.5.5 48 9.76 7. 37.7 SD6/ 536.5.5 476 8.76 3.9 68.3 8 DU

SD6 Hydraulic circuit arallel circuit Standard configuration with open center and side inlet and outlet. ort relief valve seat (plugged) Spool side positioner Load check valve Outlet line ort line ressure line Flow through line Inlet cover Outlet cover ort line Main relief valve Working section side lever kit 75 Description example: SD6//C(YG3--)/8L/8L/RC--SE DU 9

SD6 Hydraulic circuit Series -parallel (tandem) circuit It needs a special working section kit (see page ) andem section is fed from thr free flow pressure line; it s excluded when an up strem section is operated. Series circuit It needs a special working section kit (see page ). he return oil from service ports feed the remaining down stream sections. S tandem working section S series working section 75 75 Description example: SD6//C(YG3--)/8L/S--8L/...--SE Description example: :SD6//C(YG3--)/S--8L/--8L/...--SE Right inlet directional valve 75 Description example: SD6//C(YG3--)/8L/8L/RC--SE DU

SD6 erformance data (pressure drop vs. flow) Open center From side inlet to side outlet. 4 (bar) 5 5 (US gpm) 54 (psi) ressure drop 3 sections 8 sections 4 sections section 36 8 4 6 Flow (l/min) Inlet to work port From side inlet to port (spool in position ) or port (spool in position ). 4 (bar) ressure drop 3 ( ) ( ) 5 5 (US gpm) 54 (psi) 36 8 4 6 Flow (l/min) Work port to outlet From port (spool in position ) or port (spool in position ) to side outlet. 4 (bar) 3 5 5 (US gpm) 54 (psi) ressure drop ( ) ( ) 36 8 NOE -- Measured with spool type. 4 6 Flow (l/min) DU

SD6 zzrzzr Codici Ordering di codes6. ordinazione. Description example: standard configuration with side inlet and outlet st section following section SD6 / / C(YG3 -) / - 8L / DFG / - 8L / RC - SF - SE No.ofworking section. It s not necessary to indicate the letter in the complete valve description with parallel circuit (standard); in case of other circuits, they must be specified by the related letter (S, S).. 3. 4. 5. 4. 6... 5. 6. 3. 3. Intermediate section * page 64 YE CODE DESCRIION DFG 643 ressure compensated flow divider section EI(YG3) 645 With direct overpressure relief valve EI(YG3) 6465 With direct overpressure relief valve and auxiliary inlet For special configuration see page 67.. Complete inlet cover * page 4 YE CODE DESCRIION C(JG3 -) 65 Side inlet with VMDJ direct pressure relief valve C(YG3 -) 654 Side inlet with VMDY direct pressure relief valve D(YG3 -) 65 Upper inlet with VMDY direct pressure relief valve For special configuration see page NO G.. Complete working section * page YE CODE DESCRIION -8L 65 arallel circuit, prearranged for port valves, double acting spool with spring return, lever control S -8L 655 s previous with series circuit S -8L 65 s previous with series -parallel (tandem) circuit NOE (*) -- Items are referred to UN- UNF thread. 4. Complete outlet cover * page 7 YE CODE DESCRIION RC 6354 Side outlet RD 635 Upper outlet RE 635 Upper outlet with side carry -over RK 6353 Upper outlet with closed centre 5. Fixing bracket page 99 YE CODE DESCRIION SF 5S6 rackets with fixing screws 6. ssembling kit CODE 5IR87 5IR855 5IR893 5IR83 5IR869 5IR837 5IR8345 5IR8383 5IR84 5IR8459 5IR8497 5IR8535 DIRECIONL VLVE ie rod kit for section valve ie rod kit for sections valve ie rod kit for 3 sections valve ie rod kit for 4 sections valvei ie rod kit for 5 sections valve ie rod kit for 6 sections valve ie rod kit for 7 sections valve ie rod kit for 8 sections valve ie rod kit for 9 sections valve ie rod kit for sections valve ie rod kit for sections valve ie rod kit for sections valve DU

SD6 Ordering codes Description example: configuration with side inlets and mid return manifold: st section following section SD6 / / C(YG3 -) / - 8L / CS / - ED - 8L / C(YG3 -) - SF - SE No.ofworking section.. 8. 9.. 5. 9.. 7. 8... 5. 7. 7. ssembling kit for valve with CS CODE 5IR893 5IR83 5IR869 5IR837 5IR8345 5IR8383 5IR84 5IR8459 5IR8497 DIRECIONL VLVE (with CSM) ie rod kit for sections valve (with CS) ie rod kit for 3 sections valve (with CS) ie rod kit for 4 sections valve (with CS) ie rod kit for 5 sections valve (with CS) ie rod kit for 6 sections valve (with CS) ie rod kit for 7 sections valve (with CS) ie rod kit for 8 sections valve (with CS) ie rod kit for 9 sections valve (with CS) ie rod kit for sections valve (with CS) 8. Return manifold page 64 YE CODE DESCRIION CS 645 Mid return manifold with G/ outlet port 9. Complete right inlet working section * YE CODE DESCRIION -ED-8L 6575 arallel circuit, prearranged for port valves, double acting spool with spring return, lever control S-ED-8L 658 s previous with series circuit S -ED -8L 653 s previous with series -parallel (tandem) circuit.complete right inlet cover * YE CODE DESCRIION C(JG3 -) 65 Side inlet with VMDJ direct pressure relief valve C(YG3 -) 653 Side inlet with VMDY direct pressure relief valve D(YG3 -) 653 Upper inlet with VMDY direct pressure relief valve For special configuration see page NO G. NOE (*) -- Items are referred to UN- UNF thread; sections and covers for right inlet are different from the standard (see ref. e ) because of different components assembling DU 3

SD6 inlet cover Ordering codes7. Description example: FE SD6 / C (YG3 - ) EL - MN/4 - SE - VDC *.. 3.. 3. vailable configurations ressure relief valve setting (bar) C: with side inlet, for left inlet (standard) directional valve D: with upper inlet, for left inlet (standard) directional valve C: with side inlet, for right inlet directional valve D: with upper inlet, for right inlet directional valve See page 5. 3.. MN4 SV. F. Y L EL MN4. SV. Inlet cover body * page 5 CODE DESCRIION 3FI67+3X85 Standard 3FI67+5MN64 With G/4 pressure gauge prearrangement 3. Inlet valve options page 7 YE CODE DESCRIION F 5KI46 Inlet anti -cavitation valve L 5KI467* Hydraulic pilot unloader valve EL 5CR4636 VDC electromagnetic controlled unloader valve 5CR463 4 VDC electromagnetic controlled unloader valve SV X638 Relief valve blanking plug NOE (*) -- Items are referred to UN- UNF thread.. Inlet relief options page 6 YE CODE DESCRIION VMD5/ balanced direct pressure relief valve type Y (YG) 5KI5 Range 63 to 5 bar / 9 to 8 psi standard setting 8 bar / 5 psi (YG3) 5KI53 Range to bar / 45 to 9 psi standard setting bar / 75 psi (YG4) 5KI54 Range 6 to 35 bar / 3 to 46 psi standard setting 5 bar / 36 psi Standard setting is referred to l/min flow. SV X638 Relief valve blanking plug Direct pressure relief valve type J is available on request: contact Customer Service (JG) 5KI54 Range 4 to 8 bar / 58 to 5 psi standard setting 8 bar / 5 psi (JG3) 5KI543 Range 63 to bar / 9 to 9 psi standard setting bar / 75 psi (JG4) 5KI544 Range 6 to 35 bar / 3 to 46 psi standard setting bar / 3 psi 4 DU

inlet cover SD6 Dimensional data and hydraulic circuit For left inlet directional valve (standard) With side inlet, type C llenwrench6 4 Nm / 7.7 lbft Example: C(YG3--)--SE SE8 8.5 3.5 8 3.5 3.8 4.5.59 With upper inlet, type D SE8.39 Directional control valve mounting face 8 3.5 4.4 6.63 9.35.47 M8.3.4 75 llenwrench6 4 Nm / 7.7 lbft Example: D(YG3--)--SE 43.5.7 75 For right inlet directional valve With side inlet, type C llenwrench6 4 Nm / 7.7 lbft Example: C(YG3--)--SE SE8 75 With upper inlet, type D llenwrench6 4 Nm / 7.7 lbft SE8 Example: D(YG3--)--SE 75 DU 5

SD6 inlet cover Inlet relief options Direct overpressure relief valve VMD5 ( Y G 3 - ) ressure setting in bar (for standard value see page 4) djustable spring type (,3,4). djustment type (G, H) djustment type G: with screw H: valve set and locked Wrench - 4 Nm / 3 lbft Wrench3-4Nm/7.7 lbft llenwrench4 Cap code: 3CO76 max. 5.5 64.5 max..3.54 erformance data 4 (bar) 3 Spring nr. (green band) Spring nr. 3 (blue band) Spring nr. 4 (red band) 5 5 (US gpm) 5 5 (US gpm) 5 5 (US gpm) (psi) 4 4 (psi) (bar) (bar) 45 3 45 3 45 ressure 3 5 ressure 3 5 ressure 3 5 4 6 Flow (l/min) 4 6 Flow (l/min) 4 6 Flow (l/min) SV: relief valve blanking plug (% ) 5% ime response llenwrench 4 Nm / 3 lbft ressure 95% 9% % bar 45 psi OVERSHOO 75 bar 5 psi.3 IME RESONSE. RNSIEN RECOVERY IME ime ( ) 6 DU

inlet cover SD6 Inlet valve options Hydraulic pilot unloader valve, type L X Wrench 4 4 Nm / 3 lbft Wrench 4 Nm / 7.7 lbft (bar) ressure 5 5 ressure drop curve 5 5 (US gpm) 5 5 SE6 4.3.59 Operating features Internal leakage... 4 6 Flow (l/min) : cm 3 /min a bar.6 in 3 /min at 45 psi 75 Description example: C(YG3--)L-SE Solenoid pilot unloader valve, type EL With push and twist manual override with detent. ush and twist override Wrench4-4Nm/3 lbft 3Nm/. lbft (bar) ressure 5 5 ressure drop curve 5 5 (US gpm) (psi) 5 5 8 3.5 4 6 Flow (l/min) Operating features VLVE Internal leakage (in excited position): null COIL Depending on model: see features on next page 75 Description example: C(YG3--)EL -VDC--SE DU 7

SD6 inlet cover Inlet valve options Solenoid pilot unloader valve, type EL COILS CODES CONNECION YE M J Voltage ISO44 with diode without diode Deutsch D VDC X43 X435 X43 X434 4 VDC X434 - - X4344 Need connector type (sse page 98) C C8 C8 C9 Coil with ISO44 connector Coil with M J connector Coil with Deutsch D connector Connector side Connector side Connector side Nominal voltage tolerance: ±% ower rating...: 7 W Nominal current...:.58 - VDC :.8-4VDC Coil insulation...: Classe F Weather protection...: I65 Duty cycle...: % Nominal voltage tolerance: ±% ower rating...: 7 W Nominal current...:.3 - VDC :.74-4VDC Coil insulation...: Classe F Weather protection...: I65 Duty cycle...: % NOE: circuit with and without bidirectional diode Nominal voltage tolerance: ±% ower rating...: W Nominal current...:.76 - VDC :.9-4VDC Coil insulation...: Classe H Weather protection...: I67 Duty cycle...: % NOE: circuit with bidirectional diode nticavitation valve type F Wrench 4 4 Nm / 3 lbft Wrench 9 4 Nm / 7.7 lbft (bar) ressure 5 5 ressure drop curve 5 5 (US gpm) 5 (psi) 5 6.5.65 4 6 Flow (l/min) 75 Description example: C(YG3--)F--SE 8 DU

inlet cover SD6 R commutator configuration Manual rotary ackhoe clamp device. Normally mounted on the lever side, into the main relief valve cavity, properly modified. Main relief valve available in the opposite side. vailable for left inlet (standard) and right inlet valve. SE6 os. VMDY direct overpressure relief valve. For information see page 6. X os. 3.8 59.3.7 4.36 8 5 3.5.59 4.37 53.5. 79.5 3.3 X os..47 67.64 59.3 5 os. Hydraulic circuit and ordering codes Left inlet Right inlet X X C(YG3--)R -SE code: 656 C(YG3--)R -SE code: 655 DU 9

SD6 inlet cover S flow regulator configuration. Inlet cover with flow regulator on lever side: prioritary flow to working sections and exceeding flow to tank line. Inlet cover description example : FE SD6 / C (YG3 -) S N - SE 9.35 C.39.. 3.. 4. 7.5.69 Following sections Directional control valve mounting face 5 5.94 9.75 5.5.83. 8 3.5 85.5 3.37 58.8 SE8 3. Wrench 6 4 Nm / 7.7 lbft C-C 4.57 3.8. 4. C 48.89.. Complete inlet cover Hydraulic circuit YE: C(YG3 -)SN -SE CODE: 67 DESCRIION: Side inlet, VMDY overpressure relief valve and N handwheel flow control valve NOE: For other configurations please contact Sales Dept. C R Description example: SD6/4/C(YG3 -)SN/8L/8L/...--SE8()6() Following sections. Inlet cover body CODE: 3FI6775+3X873+3X85 DESCRIION: ype C -D -C -D, port = SE8, prearranged for flow control 3. Inlet relief options Direct overpressure relief valves type Y and J: see page. 4. Flow control valve YE CODE DESCRIION M S Handwheel control N S6363 Handwheel control with detent W S5 VDC proportional solenoid valve DU

inlet cover SD6 S flow regulator configuration Handwheel operated Continuous fine regulation One turn with detent Valve circuit Wrench3-4Nm/7.7 lbft Wrench3-4Nm/7.7 lbft C R 33.5.3 38.5 47.85 9.5 3.64 75 With proportional solenoid control Wrench 3 4 Nm / 7.7 lbft ISO44 connection (needs connector typre C, see page 98) Valve circuit C R 5 4.53 35.38 Emergency push -button Solenoid operating features Nominal voltage.. : VDC ower rating... : 7,4 W Duty cycle... : % otentiometer for valve adjustment 75 Example of solenoid flow control valve connection It s show a configuration with push--button panel type U model U//SC: for information contact Sales Dept. SO o battery Connector ISO44 erformance data 4 (l/min) rioritary flow 3 ressure -flow diagram Qin = 45 l/min 3 (psi) (US gpm) 9 6 3 Flow regulation diagram Qin=45l/min( US gpm) - = bar (45 psi) (l/min) 6 rioritary flow 4.3.6.9. Current () (US gpm) F 5 J Y 5 F Y J Flow control valve type M Flow control valve type N Flow control valve type W 3 9 5 7 ressure (bar) 3 4(n.of turn) 4 8 6 4 (n.of clicks) DU

SD6 working section Ordering codes3. Description example: EL SD6 / - 8 L. (G3-5) - SE * EL SD6 / - M 8IM - SE.. 3. 4. 5. ort valves setting in bar mounted on port. mounted on port. 3 mounted on and port. 6. 3. II 8-5. 4. 9 I U L C SL 8 3 Q. LC 8ED3. II. Working section kit * page 4 YE CODE DESCRIION 5EL67 With paralle circuit S 5EL67 With serie circuit S 5EL367 With serie -parallel (tandem) circuit Include body, seals, rings and load check valve.. Spools page 5 YE CODE DESCRIION 3CU3 Double acting, 3 positions, with and closed in neutral position CS 3CU Double acting, 3 positions, with and closed in neutral position, sensitive type 3CU3 Double acting, 3 positions, with open to tank in neutral position... follow. Spools YE CODE DESCRIION 3CU3 Double acting, 3 positions, with open to tank in neutral position 3CU53 Double acting, 3 positions, with and open to tank in neutral position 3 3CU33 Single acting on, 3 positions, plugged; requires G/ plug (see part I) 4 3CU353 Single acting on, 3 positions, plugged; requires G/ plug (see part I) Special spools for particular positioner kits... page 9 5Y 3CU44 Double acting, 4 positions, float in position 3 with spool in 5Y 3CU433 Double acting, 4 positions, float in position 3 with spool out 8 3CU6 Double acting, 4 positions, regenerative in position 3 DU

working section SD6 4.Ordering codes 3. side spool positioners page 3 YE CODE DESCRIION 7F 5V745 With friction and neutral position sensor 8 5V85 With spring return in neutral position 8D 5V85 s type 8 and pin with M6 female thread for dual control 8D 5V85 s type 8 and pin with 8mm/.3 in radial hole 8D3 5V853 s type 8 and pin with M8 female thread for dual control 8F 5V85 s type 8 and adjustable flow limiter 9 5V95 positions, with spring return in neutral position from position 5V95 positions, with spring return in neutral position from position 9Z 5V9 With detent in position and spring return in neutral position Z 5V With detent in position and spring return in neutral position Z 5V With detent in position and, spring return in neutral position 8MG3(NO) 5V8566 s type 8 and operation with microswitch in positions and, contact normally open 8MG3(NC) 5V8566 s previous, with contact normally closed 8RM 5V8659 s type 8 and VDC electromagnetic detent in position 5V86595 s previous, 4VDC 8MHE3(NC) 5V8654 s type 8 and spool postioning ON/OFF electric signal circuit normally closed 8MHE3(NO) 5V8654 s previous, with circuit normally open 8K 5V875 s type 8 and VDC solenoid lock device 5V8754 s previous 4 VDC 8 5V857 ON/OFF pneumatic kit 8EG3 5V85738 ON/OFF VDC electro -pneumatic kit 5V85743 ON/OFF 4 VDC electro -pneumatic kit 8ED3 5V8535 ON/OFF VDC electro -hydraulic kit 5V8535 ON/OFF 4 VDC electro -hydraulic kit articular positioner kits for special spools... page 45 3NZ 5V335 4 positions with spring return in neutral position and detent in pos.3: for spool 5Y 3QN 5V345 4 positions with spring return in neutral position and detent in pos.3: for spool 5Y 3F 5V356 4 positions with spring return in neutral position: for spool 8 3QNMG3(NO) 5V34566 s type 3QN with microswitch operation in positions and : for spool 5Y 4. side options page 49 YE CODE DESCRIION L 5LEV5 Standard lever box LM 5LEV5 Lever box with M thread LF 5LEV5 Lever box with adjustable flow limiter in pos. LFG5 5LEV58 Cast iron lever box with adjustable flow limiter in positions and L 5LEV35 Steel lever box with pivot placed down L3 5LEV35 Steel lever box with pivot placed above SL - Withou lever box SL 5CO5 Without lever box, with dust -proof plate SLCZ 5CO53 Without lever box, with endcap... follow 4. side options YE CODE DESCRIION LE 5LEV65 Safety lever box LU 5LEV855 Safety lever box, horizontal type Q 5EL5 Flexible cable connection; for CD cables LC 5CLO6 Joystick lever for sections operation 5. ort valves page 59 YE CODE DESCRIION ssembled on section 3 X548 and ports valve blanking plugs C 5KI46 nti -cavitation nti -shock valve (G) 5KI6 From 5 to 5 bar / 75 to 8 psi standard setting 63 bar / 9 psi (G3) 5KI63 From to bar / 45 to 9 psi standard setting bar / 45 psi (G4) 5KI64 From 6 to 35 bar / 3 to 46 psi standard setting bar / 9 psi nti -shock and anti -cavitation valve U(G) 5KI36 From 5 to 5 bar / 75 to 8 psi standard setting 63 bar / 9 psi U(G3) 5KI363 From to 5 bar / 45 to 36 psi standard setting bar / 8 psi U(G4) 5KI364 From 6 to 35 bar / 3 to 46 psi standard setting bar / 9 psi Standard setting is referred to l/min flow. Flange mounted type X673 and S valves blanking plug Direct type 6* lock with valve on port 6* lock with valve on port 3 6* lock with valves on ports and XCR65 Single valve With re -opening S 633* lock with valve on port S 634* lock with valve on port S3 63* lock with valves on ports and S XCR65 Single valve 6. Complete controls page 54 8IM* proportional hydraulic and 8ES -- 8ESN ON/OFF electric control kits. I and ports plug * YE CODE DESCRIION SE6 3X873 lug for single acting spool II Optional handlevers YE CODE DESCRIION L/M8x5 75 For L lever box, L = 5 mm / 5.9 in L/Mx5 75 For LM and LFG5 lever boxes, L = 5 mm / 5.9 in L8/Mx 73 For LC joystick, L = mm / 7.87 in NOE (*) -- Items are referred to UN- UNF thread. DU 3

SD6 working section Dimensional data and hydraulic circuit hey are available with parallel or tandem circuit, with or without ports relief valves prearrangement. arallel circuit SE6 87 3.43 Series circuit 4.7.79 Directional control valve mounting face Description example: -- 8L -- SE 87 3.43 Directional control valve mounting face Series -parallel (tandem) circuit 8.5.33 Description example S-- 8L -- SE 87 3.43 Directional control valve mounting face Description example S-- 8L -- SE 4 DU

working section SD6 Spools ype LC " stroke + 5.5 mm +.in LC ------ closed, with flow through line (LC) open LC stroke - 5.5 mm -. in erformance data 6 (l/min ) Spool metering ().. (in) 5 (US gpm) 6 (l/min ) Spool metering ().. (in) 5 (US gpm) Flow 4 4 Y F J J F 5 Y Qin = 45 l/min / US gpm 5 F (on ports) = 63bar / 9 psi Y (on ports) = bar / 45 psi... 3. 4. 5. 5.5 J (on ports) = 5bar / 36 psi... 3. 4. 5. 5.5 Stroke (mm) Stroke (mm) Flow DU 5

SD6 working section Spools ype CS LC " stroke + 5.5 mm +.in LC ------ closed, with flow through line (LC) open LC stroke - 5.5 mm -. in erformance data 6 (l/min ) Spool metering ().. (in) 5 (US gpm) 6 (l/min ) Spool metering ().. (in) 5 (US gpm) Flow 4 F Y J 5 Qin = 45 l/min / US gpm F (on ports) = 63bar / 9 psi F Y (on ports) = bar / 45 psi... 3. 4. 5. 5.5 J (on ports) = 5bar / 36 psi... 3. 4. 5. 5.5 Stroke (mm) Stroke (mm) Flow 4 Y J 5 6 DU

working section SD6 Spools ype LC -- closed,, with flow through line (LC) open ype LC -- closed,, with flow through line (LC) open ype LC closed, --, with flow through line (LC) open DU 7

SD6 working section Spools ype 3 ort plugged llen wrench 6-4 Nm / 7.7 lbft LC ---- closed, with flow through line (LC) open ype 4 ort plugged llen wrench 6-4 Nm / 7.7 lbft LC ---- closed, with flow through line (LC) open 8 DU

working section SD6 Spools ype 5Y It needs special body with extra machining type -5Y code 5EL633. It must be coupled only with spool positioner 3NZ (see page 45). 3 LC " stroke + 4.5 mm +.8in 3 LC ------ closed flow through line (LC) open 3 LC stroke - 4.5 mm -.8 in 3 LC stroke - 9 mm -.35 in -- (float in detent) erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi.. (in) 6 (l/min ) 5 (US gpm) Flow 4... 3. 4. 5. 5.5 Stroke (mm) 5 ressure 4 (bar) 3 ressure drop in position 3 (last section) 5 5(US gpm) (psi) 5 3 45 6 Flow (l/min) DU 9

SD6 working section Spools ype 5Y It needs special body with extra machining type -5 code 5EL635. It must be coupled only with spool positioner 3QN (see page 45). 3 LC " " stroke + 9 mm +.35in -- (float in detent) 3 LC " stroke + 4.5 mm +.8in 3 LC ------ closed flow through line (LC) open 3 LC stroke - 4.5 mm -.8 in erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi.. (in) 6 (l/min) 5 (US gpm) ressure 4... 3. 4. 5. 5.5 Stroke (mm) 5 ressure drop in position 3 (last section) 5 5(US gpm) (psi) (bar) ressure 5 () 5 5 3 45 6 Flow (l/min) 3 DU

working section SD6 Spools ype 8 It needs special body with extra machining type -8 code 5EL635. It must be coupled only with spool positioner 3F (see page 46). 3 LC " stroke + 5 mm +.in 3 LC ------ closed flow through line (LC) open 3 LC stroke - 5 mm -. in 3 LC stroke - 8.5 mm -.33 in + (rigenerativo) erformance data Spool metering Qin = 45 l/min - US gpm / (on ports) = bar - 45 psi.. (in) 6 (l/min ) 5 (US gpm) Flow 4... 3. 4. 5. 5.5 Stroke (mm) 5 ressure ressure drop in position 3 (last section) 5 5(US gpm) (psi) (bar) 5 5 5 3 45 6 Flow (l/min) DU 3

SD6 control kits side spool positioners With spring return 8kit It s supplied with standard spring type D (see force--stroke diagram). It s available with lighter spring type C (8MC code: 5V85) or heavier type E (8ME code: 5V845). llenwrench4 6.6 Nm / 4.9 lbft llenwrench5 9.8 Nm / 7. lbft 36.5.44 Force -stroke diagram -. -... (in) 3 (lbf) (N) E 6 D 4 C Force - C - D - - 4 E - 6-3 - 6-5 - 4-3 - - 3 4 5 6 Stroke (mm) 8D kit It s available with lighter spring type C (8DMC code: 5V85); see previous diagram. Spool end joint code XER354 is available on request in order to screw onto pin. Spool end joint dimension llenwrench4-6.6nm/4.9 lbft Wrench 9-9.8 Nm / 7. lbft.47 5h.59 4.6.39.79 8.3 M6.43 M6 36.5.44 44.73 8.3 8.7 4.57 8D kit llenwrench4-6.6nm/4.9 lbft Wrench 9-9.8 Nm / 7. lbft.43 M8 4 36.5.57 84.44 3.3 3 DU

control kits SD6 side spool positioners With spring return 8D3 kit Chiave 4-6,6 Nm Chiave - 9,8 Nm M8 48,5 36,5 8F kit With spool stroke adjustment in position ( ). llen wrench 5-9.8 Nm / 7. lbft llenwrench4-6.6nm/4.9 lbft Wrench 3 4 Nm / 7.7 lbft llenwrench4 M8x 36.5.44 5.5.3 9 kit kit llenwrench4-6.6nm/4.9 lbft llenwrench5 9.8 Nm / 7. lbft llenwrench4-6.6nm/4.9 lbft llenwrench5 9.8 Nm / 7. lbft 36.5.44 36,5.44 DU 33

SD6 control kits side spool positioners With detent and sprimg return to neutral from either directions 9Z kit llenwrench4-6.6nm/4.9 lbft Wrench 5-9.8 Nm / 7. lbft 7.5.85 3 (N) Force - Force -Stroke diagram ort ort -. -. Detent area - - 4-3 - 6-6 - 5-4 - 3 - - 3 4 5 6 Stroke (mm) - 5.5.. (in) Detent force: N / 7 lbf ±% / Release force: 3 N / 5.7 lbf ±% 3.3 5.5 (lbf) 6 4 - Z kit llenwrench4-6.6nm/4.9 lbft Wrench 5-9.8 Nm / 7. lbft 7.5.85 3 (N) Force - Force -Stroke diagram ort ort -. -. Detent area - - 4-3 - 6-6 - 5-4 - 3 - - 3 4 5 6 Stroke (mm) - 5.5-3.3.. (in) Detent force: N / 7 lbf ±% / Release force: 3 N / 5.7 lbf ±% 5.5 (lbf) 6 4 - Z kit llenwrench4-6.6nm/4.9 lbft Wrench 5-9.8 Nm / 7. lbft 7.5.85 3 (N) Force - Force -Stroke diagram ort ort -. -. - - 4-3 - 6-6 - 5-4 - 3 - - 3 4 5 6 Stroke (mm) - 5.5-3.3 Detent area.. (in) Detent force: N / 7 lbf ±% / Release force: 3 N / 5.7 lbf ±% 3.3 5.5 (lbf) 6 4-34 DU

control kits SD6 side spool positioners 8MHE3 kit: with spring return in neutral position and spool positioning ON/OFF signal his module supplies two different ON/OFF signals, related to the direction of the spool. It has two separate contacts which can be normally open or normally closed. It can be used with standard spools and working section (working section kit without ring on side ) Notch - 6.6 Nm / 4.9 lbft llenwrench4 6.6 Nm / 4.9 lbft llenwrench5 9.8 Nm / 7. lbft Female connector HIRSHMNN on request (see type C at page 98) Connector wiring osition signal 33.5.3 3 4 Operating features ower supply range : / 4 VDC Max. output current. : 5 m Weather protection. : I65 44.5.75 8 3.9 See view Wrench 9 9.8 Nm / 7. lbft osition signal 8MHE3(NC) kit 8MHE3(NO) kit 4 3 4 3 Configuration with normally closed circuit Configuration with normally open circuit View View Mobile contact Fixed contact Mobile contact Fixed contact (VDC) % -. Ouput signal with NC circuit olerance range -... (in) (VDC) % -. Ouput signal with NO circuit olerance range -... Voltage Voltage -6-5 -4-3 - - 3 4 5 6 Stroke (mm) -6-5 -4-3 - - 3 4 5 6 Stroke (mm) DU 35

SD6 control kits side spool positioners With microswitch type 8MG3 With spring return in neutral position and microswitch operated in both directions. lso available 8MG(NO) configuration, code 5V8567 (microswitch operated in position ) and 8MG(NO) configuration, codice 5V8568 (microswitch operated in position ); dimensions are the same of 8MG3 configuration. heese configurations are available also with nornally closed (NC) contact. Microswitch with connector Wrench 9.8 Nm / 7. lbft llenwrench4 6.6 Nm / 4.9 lbft Wrench 4 Nm / 3 lbft Kit 8MG3(NO) Other configurations Kit 8MG(NO) llenwrench5 9.8 Nm / 7. lbft 66.5.6 llenwrench4 6.6 Nm / 4.9 lbft Operating features MICROSWICH Mechanical life... : 5x 5 operations Electric life (resistive load) : 5 oper. - 7 / 3.5VDC :5x 4 oper. - / VDC :5x 4 oper. - 3 / 8VDC Kit 8MG(NO) COMLEE CONROLS CODES CONROL YE Need Contact 8MG3 8MG 8MG connector type NO 5V8566 5V8568 5V8567 C7 see page NC 5V8566 5V8568 5V8567 C7 98 36 DU

control kits SD6 side spool positioners With microswitch type 8MG3 More configurations and spare parts It s possible to obtain further configurations of complete control, using the MG kit, microswitches and 3 positions side spool positioner, as following draw. Standard microswitches: Flying leads with connector Microswitch Normally open (NO) code 4MIC73 with CKRD W -CK female connector with male end Normally closed (NC) code 4MIC74 with CKRD W -CK male connector with female end 84.5 8 3.33 5.4 3 positions side spool positioner type 9,,. (see page 34) Kit MG Wrench 4 Nm / 3 lbft Wrench 4 Nm / 3 lbft Kit MG3 code: 5KI85 Kit MG code: 5KI85 Kit MG code: 5KI85 Special microswitches: moulded -in connector Normally open (NO) code 4MIC73 or normally closed (NC) code 4MIC74 With CKRD W -CK female connector with female end Wrench 4 Nm / 3 lbft 33.3 he microswitches with moulded -in connector are not interchangeable with the flying leads ones since these need a different connector: type C4 (see page 98). DU 37

SD6 control kits side spool positioners Solenoid lock device type 8K With spring return and spool electromechanical lock in neutral position; when coil is feeded the spool can be moved. Operating features CUOR Lock stroke... : 3.5 mm /.4 in COIL Depending on model: see following features Coil with ISO44 connector llenwrench4 6.6 Nm / 4.9 lbft Wrench 4 9.8 Nm / 7. lbft 84.5 3.33 Wrench 9.8 Nm / 7. lbft llenwrench5 9.8 Nm / 7. lbft llenwrench4 6.6 Nm / 4.9 lbft 8.5 3. 3.6 Nom. voltage tolerance... : ±% ower rating... : 8 W Nominal current... :.58 - VDC :.8-4VDC Coil insulance... : Class F Weather protection... : I65 Duty cycle... : % Coil with Deutsch D connector COMLEE CONROL CODES CONNECION YE ISO44 Deutsch D ackard M -ack CONROL YE Voltage 8K 8K4 8K6 VDC 5V876 5V8764 5V8766 4 VDC 5V8764 5V87644 5V87664 Need connector type (see page 98) C C9 C Nom. voltage tolerance... : ±% ower rating... : W Nominal current... :.9 - VDC :.95-4VDC Coil insulance... : Class H Weather protection... : I65 Duty cycle... : % Coil with ackard M -ack connector 49.93 634 4.96 Nom. voltage tolerance... : ±% ower rating... : 8 W Nominal current... :.58 - VDC :.8-4VDC Coil insulance... : Class F Weather protection... : I65 Duty cycle... : % 38 DU

control kits SD6 side spool positioners Solenoid lock device type 8K More configurations and spare parts It s possible to obtain further configurations of complete control, using the K kit, coils and 3 positions side spool positioner, as following draw: for information contact Sales Department. Coil COIL CODES CONNECION YE Voltage ISO44 Deutsch D ackard M -ack VDC X43 X434 YSOL33 4 VDC X434 X436 YSOL35 Fitted with actuator: code: 5KI86 3 positions side spool positioner type 9Z, Z, Z. (see page 34) Kit K 8 ON/OFF pneumatic control Wrench 9.8 Nm / 7. lbft N /8 nr. threads V V llenwrench4 6.6 Nm / 4.9 lbft V 5.5.3 3.9 V Operating features ilot pressure... : min 5.5 bar / 8 psi : max bar / 45 psi Wrench 9.8 Nm / 7. lbft 8 4.65 llenwrench4 6.6 Nm / 4.9 lbft DU 39

SD6 control kits side spool positioners Electromagnetic detent type 8RM With electromagnetic detent in position and spring return to neutral position. Needs special working section body kit without washer on positioner side. Solenoid kit with connector Notch. mm /.47 in 6.6 Nm / 4.9 lbft Wrench - 9.8 Nm / 7. lbft 88.5 3.48 8 4.5 Operating features COIL Niminal voltage... : / 4 VDC ± % ower rating... : 5.5 W Resistance ( C)... : 6. / 5 Ohm Min. release force... : N -.5 lbf Duty cycle... : % llenwrench4-6.6nm/4.9 lbft COMLEE CONROL CODES CONNECION YE Deutsch D M ackard M -ack CONROL YE Voltage 8RM 8RM() 8RMM(35) VDC 5V8659 5V8659 5V86593 4 VDC 5V86595 5V86596 5V86598 Need connector type (see page 98) C9 C C Coil with Deutsch D connection 6 3.6 Coil with M Fastin -Faston connection 7.87 COIL CODES CONNECION YE Voltage Deutsch D M ackard M -ack VDC YSOL53455 YSOL5345 YSOL5345 4 VDC YSOL53456 YSOL53458 YSOL53457 Coil with ackard M -ack connection 374 4.7 4 DU

control kits SD6 side spool positioner 8E3 ON/OFF electro -pneumatic control g9 Wrench 5-6.6 Nm / 4.9 lbft 43 57.69.4 Scheme V V llenwrench4 6.6 Nm / 4.9 lbft 3.5 4.47 V V Scheme ISO 9 4.65 Ø6 Ø.4 V V llenwrench4 6.6 Nm / 4.9 lbft 9 4.69 47 5.79 Wrench 3 4 Nm / 7.7 lbft Wrench 9 Special wrench - 9.8 Nm / 7. lbft COMLEE CONROL CODES CONNECION YE ISO695 CONROL YE Flying leads Voltage 8EG3 8EG35 VDC 5V85738 5V85736 4 VDC 5V85743 5V8574 Need connector type (see page 98) C (included) / Operating features CONROL ilot pressure... : 6 bar / 87 psi : (max.5 bar / 8 psi) COIL Nominal voltage tolerance... : ±% ower rating... : 8 W Nominal current... :.67 - VDC :.33-4VDC Coil insulation... : Class H Weather protection... : I65 Duty cycle... : % Voltage COIL CODES CONNECION YE ISO695 Flying leads * VDC X X 4 VDC X4 X4 * Several type of connectors can be wired on request: contact Sales Department. Coil with ISO695 connector Coil with flying leads 7.87 DU 4

SD6 control kits side spool positioner 8ED3 ON/OFF electro -hydraulic control ON/OFF electro--hydraulic control with external pilot and drain. Chiave - 5 Nm 39 5.47 4 59.65.3 L V Scheme /.39 Coil 39.5 5.49 Solenoid valve: wrench 4-9.8 Nm / 7. lbft Wrench -4Nm/7.7 lbft Scheme ISO 9 Collettore V L Wrench 6 4.57 33 5.4 llenwrench4-6.6nm/4.9 lbft llenwrench4-6.6nm/4.9 lbft Special wrench 9.8 Nm / 7. lbft Operating features CONROL ilotpressure... :min.bar/45 psi : max. 5 bar / 75 psi Max backpressure on drain L... : 5 bar / 36 psi COIL Nominal voltage tolerance... : ±% ower rating... : W Nominal current... :.75 - VDC /.87-4VDC Coil insulation... : Class F Weather protection... : depending on coil connector Duty cycle... : % COMLEE CONROL CODES ISO44 CONNECION YE without diode M J CONROL YE with diode Deutsch D Voltage 8ED3 8ED3 8ED3D 8ED34 VDC 5V8535 5V855 5V858 5V8545 4 VDC 5V8535 5V855 5V858 5V8545 Need connector type (see page 98) C C8 C8 C9 4 DU

control kits SD6 side spool positioner 8ED3 ON/OFF electro -hydraulic control COIL CODES CONNECION YE M J Voltage ISO44 without diode with diode Deutsch D VDC X4 X4 X4 X44 4 VDC X44 X44 X44 X444 Coil with ISO44 connection (weather protection: I65) Coil with M J connection (weather protection: I65) Coil with Deutsch D connection (weather protection: I67) 45 5.7 3.94 Collector kit for external pilot and drain V L SE 6 V L bar 9 psi 59 6.6 Collector 75 COLLECOR KI CODES Description example: SD6//C(YG3--)/8ED3L/8ED3L/RC--KES -SE -4VDC ype Code * Description KES 5KES7 Kit one section KES 5KES7 Kit for sections KE3S 5KE3S7 Kit for 3 sections KE4S 5KE4S7 Kit for 4 sections KE5S 5KE5S7 Kit for 5 sections KE6S 5KE6S7 Kit for 6 sections KE7S 5KE7S7 Kit for 7 sections (*) codes are referred to UN -UNF thread DU 43

SD6 control kits side spool positioners 8ED3 ON/OFF electro -hydraulic control Kit collettore con linee di pilotaggio e drenaggio he kit include collector, VR pressure reducing valve and pipes. Wrench 9 4 Nm 7.7 lbft.5 3.96 VR Code: S88VL Collector 44.73 llenwrench6 4 Nm / 7.7 lbft VR Wrench 7 Drain 5 Inlet line Wrench 4 4 Nm / 3 lbft C Wrench 4 4 Nm / 7.7 lbft C 75 VRE Outlet cover with VRE backpressure valve (not included in the collector kit) power beyond. Description example: SD6//C(YG3--)/8ED3L/8ED3L/RV -KER3 -SE -4VDC Description type for outlet Operating features cover with VRE valve. VR VLVE Outlet pressure...: 5 bar / 363 psi Max. flow...: 8 l/min Filtering...: 8 µ COLLECOR KI CODES ype Code * Description KER 5KER37 Kit one section KER 5KER37 Kit for sections KE3R 5KE3R37 Kit for 3 sections KE4R 5KE4R37 Kit for 4 sections KE5R 5KE5R37 Kit for 5 sections KE6R 5KE6R37 Kit for 6 sections (*) codes are referred to UN -UNF thread VRE backpressure valve Valve is assembled on flow through passage of outlet cover; it s necessary to provides pilot pressure to the actuator. RV complete (with backpressure valve and tapered plug) outlet cover code: 6356 Valve VRE code: X5978 Wrench3-4Nm/3 lbft 4 (bar) 3 ressure drop C 5 5 (US gpm) (psi) 48 C SE8 ressure 3 6 apered plug DIN96 -G/4 code: 443 llen wrench 7-4 Nm / 7.7 lbft 73.5.89 33.5.3 4 6 Flow (l/min) 44 DU

control kits SD6 side spool positioners articular positioner kits for special spools 3NZ kit Detent in 4 th position with spool in: available only for spool type 5Y (see page 9). llenwrench4 6.6 Nm / 4.9 lbft Wrench 6 9.8 Nm / 7. lbft 7.5.85 3 Special section body kit Force 4 (N) 3 Floating Force -stroke diagram ort ort -.3 -. -.. -.7 - - 3-6 -4-9 -8-7 -6-5 -4-3 - - 3 4 5 Stroke (mm) - 6.8 -.8-4.5 Detent area Locking force: 8 N / 63 lbf ±% Release force: 3 N / 67.4 lbf ±% (in).7 4.5 (lbf) 6 3 3QN kit Detent in 4 th position with spool out: available only for spool type 5Y (see page 3). 7.5.85 3 llenwrench4 6.6 Nm / 4.9 lbft Wrench 6 9.8 Nm / 7. lbft Kit elemento speciale Forza 4 (N) Force -stroke diagram ort ort -.8 - - 3-6 -4-5 -4-3 - - 3 4 5 6 7 8 9 Stroke (mm) - 4.5 -. Detent area Locking force: 36 N / 8 lbf ±% Release force: 39 N / 87.7 lbf ±% 4.5 Floating...3.8.7 6.8 3 (in) (lbf) 6 3 DU 45

SD6 control kits side spool positioners articular positioner kits for special spools 3F kit 4 th position with spool in and spring return to neutral position. valable only for spool type 8 (see page 3). 3 llenwrench4 6.6 Nm / 4.9 lbft llenwrench.8 Nm /.59 lbft 8.5 3.5 llenwrench5-9.8nm/7. lbft 3QNMG3(NO) kit Detent in 4 th position with spool out, spring return to neutral position and microswitch operation in both directions. he microswitch can be configured with NO (normally open) or NC (normally closed) contact vailable only for spool type 5Y (see page 3). Wrench -4Nm/3 lbft Microswitch with connector Wrench 9.8 Nm / 7. lbft llenwrench4 6.6 Nm / 4.9 lbft 3 Wrench 6 9.8 Nm / 7. lbft.5 4.4 llenwrench4 6.6 Nm / 4.9 lbft Codes COMLEE CONROL CODES Contact type Need connector type 5V34566 NO C7 see page 5V34566 NC C7 98 Operating features MICROSWICH Mechanical life...: 5x 5 operations Electric life (resistive load)..: 5 operations - 7 / 3.5VDC :5x 4 operations - / VDC :5x 4 operations - 3 / 8VDC 46 DU

control kits SD6 side spool positioners articular positioner kits for special spools 3QNMG3(NO) kit Spare parts Standard microswitches: Flying leads with connector Microswitch Normally open (NO) code 4MIC73 with CKRD W -CK female connector with male end Normally closed (NC) code 4MIC74 with CKRD W -CK male connector with female end 84.5 8 3.33 5.4 Kit MG Wrench 4 Nm / 3 lbft Wrench 4 Nm / 3 lbft Kit MG3 code: 5KI85 Special microswitches: moulded -in connector Normally open (NO) code 4MIC73 or normally closed (NC) code 4MIC74 With CKRD W -CK female connector with female end Wrench 4 Nm / 3 lbft 33.3 he microswitches with moulded -in connector are not interchangeable with the flying leads ones since these need a different connector: C4 (see page 98). DU 47

SD6 control kits side spool positioners articular positioner kits for special spools With electromechanical lock he positioners for special spools (3NZ, 3QN), are also available with spool electromechanical lock in neutral position; if coil is excited the spool can be operated. For kit K, coils features and dimensions, see page 38: for informations contact Sales Department. COIL CODES Coil CONNECION YE Voltage ISO44 Deutsch D ackard M -ack VDC X43 X434 YSOL33 4 VDC X434 X436 YSOL35 Need connector type (see page 98) C C9 C 3NZ positioner kit (see page 45) for spool type 5Y 3QN positioner kit (see page 45) for spool type 5Y Kit K Complete actuator kit, code: 5KI86 Special section body kit depending on used spool: for information contact Sales Department. 48 DU

control kits SD6 side options Lever controls Ltype luminium lever pivot box with protective rubber bellow; it can be rotated 8 (configuration L8). Vertical handlever assembly 3 4 M8 Horizontal handlever assembly Configuration L8.79 53.7. 65.5.58.79 44.73 llenwrench4 6.6 Nm / 4.9 lbft 35.5.4 LM type LF type 54.3 7.5.8 3.7.93 o be use with M handlever. It can be rotated 8 (configuration LM8). With spool stroke adjustment in position ( ). It can be rotated 8 (configuration LF8). M M8 M.79.79 53.7. 65.5.58.79 44.73 llenwrench4 6.6 Nm / 4.9 lbft.79 44.73 max66 max.6 llen wrench.5 llenwrench4-6.6nm/4.9 lbft Wrench3-4Nm/7.7 lbft DU 49

SD6 control kits side options Lever control LFG5 type Cast iron lever pivot box with protective rubber bellow; it s complete of two screws for spool stroke adjusting in both directions. It can be rotated 8 (configuration LFG58). Vertical handlever assembly Horizontal handlever assembly M Stroke end screw for position ( ):allenwrench.5 Fixing nut: wrench 8-6.6 Nm / 4.9 lbft Stroke end screw for position ( ):allenwrench.5 Fixing nut: wrench 8-6.6 Nm / 4.9 lbft 46,5 L type Steel construction, with pivot placed down. ssembling with 5 and 5Y type spool is not possible. L3 type Steel construction, with pivot placed above. ssembling with 5, 5Y type spool and with port valves on port, is not possible llenwrench3 6.6 Nm / 4.9 lbft M8 Vertical handlever assembly Horizontal handlever assembly Vertical handlever assembly M8 Horizontal handlever assembly 7.5.5.8.8 57.4 39.5.56 48.5.9 66.5.6.79 65.5.58 8.5 3. 53,4 max.79 5.5. 3.5.8 llenwrench3 6.6 Nm / 4.9 lbft.79 9.4 Lever Spool Lever Spool ivot ivot 5 DU

control kits SD6 side options Safety lever control Safety levers with lock in neutral complete with handlever; lift handlever knob to operate. LE type lack VC standard knob 5. Stroke to ulocking Locking bush Wrench 3 4 Nm / 7.7 lbft 3 5.5.8.79.3 4 9.53 Directional control valve mounting face llenwrench4.79 44 6.6 Nm / 4.9 lbft.73 LU type vailable as LU(R5) configuration, with lenght L = 5 mm / 5.9 in and red knob: code 5LEV85. Wrench3-4Nm/7.7 lbft.79 M8 L = L = 8.66 65.56 53.7..83 lack plastic standard knob Stroke to unlocking.47 Locking bush llenwrench4-6.6nm/4.9 lbft 5.8.8 DU 5

SD6 control kits side options Controls prearrangement SL type SL type SLCZ type 9.4.79.3 8 llenwrench4 6.6 Nm / 4.9 lbft.87 9H8.35 9.35 5.59 8.3 Mechanical control with dust--proof plate kit. 7.5.85 llenwrench4-6.6nm/4.9 lbft rotection cap usable with pneumatic, electropneumatic, and electrohydraulic spool positioners. Q cable remote control kit Waterproof cap prearranged for remote control with flexible cable. Example of cable control llenwrench4-6.6nm/4.9 lbft Wrench - 9.8 Nm / 7. lbft Wrench4-4Nm/7.7 lbft CD flexible cables 8 3.9 Flexible cable NOE - For further information about remote cable control, require related documentation. SCF3 remote control Q kit SD6/ directional control valve without lever boxes 5 DU

control kits SD6 side options LC joystick nd section spool Execution LC4 st section spool ivot Wrench3-4Nm/7.7 lbft Wrench llenwrench4 6.6 Nm / 4.9 lbft llenwrench4-6.6nm/4.9 lbft Wrench3-4Nm/7.7 lbft Wrench3-4Nm/7.7 lbft llenwrench5-9.8nm/7. lbft NOE - he handlever must be ordered separately (see page 3). Dimensions and movement scheme Execution LC pivot placed down on the left Execution LC pivot placed down on the right st section axis nd section axis - - - - 36.4 - - - M 8.39. - 6.63 76.5 3. Execution LC3 pivot placed above on the left Execution LC4 pivot placed above on the right - - - - - - - - NOE - Due to limited space in case of LC3 or LC4 configuration the assembly of ports service relief valves is not possible. DU 53

SD6 control kits Complete controls8. 8ESN solenoid control Direct control by double solenoid with spring return to neutral position, available with emergency manual override. It s necessary special spool and standard body (body kit without spool seals). Description example: EL SD6 / - 8ESN LES (G3-5) - SE - 4VDC.. 3. 4. 5. 6. 7.. 7. 4. 6. 5. LES.. Complete working section * YE CODE DESCRIION -8ESNLES -4VDC 647 arallel circuit, double acting spool, solenoid control with lever 3. CE. Working section kit * YE CODE DESCRIION /IM -ES 5EL67 arallel circuit 3. Spools YE CODE DESCRIION (ESN) 3CU5 Double acting, 3 positions, with and closed in neutral position (ESN) 3CU55 Double acting, 3 positions, with and open to tank in neutral position 4. Connection kit YE CODE DESCRIION 8ESN 5V8 For solenoid joint, with spring return in neutral position 5. side options YE CODE DESCRIION LES 5LEV64 Safety lever pivot box for manual operation CE 5CO6 Endcap 6. ort relief valves For codes please refer to page 3. 7. Solenoid YE CODE DESCRIION.5VDC XSOL343 Nominal voltage.5vdc VDC XSOL343 Nominal voltage VDC 4VDC XSOL3434 Nominal voltage 4VDC 9VDC XSOL349 Nominal voltage 9VDC; (for VC supply) NOE (*) - Codes are referred to UN- UNF threads. 54 DU

control kits SD6 Complete controls 8ESN solenoid control Electric wiring example 8ESNLES kit with safety lever pivot box 3 8ESNCE kit with encadp Connector -- o battery + Operating condition diagram 4 6 8 (US gpm) 4 (bar) (psi) 3 45 Operating features CONROL Internal leakage () ( p = bar - 45 psi /=4 C) : cm 3 /min -.6 in 3 /min COIL Nominal voltage tolerance... : +% ower rating... : 65 W Coil insulance... : class H Duty cycle... : % ressure 3 Operation area 5 5 3 45 Flow (l/min) LES Manual operation: lift the bush to lever unlocking Wrench 4 4 Nm / 7.7 lbft W Connection ISO44 (needs C3 connector for VDC supply or C5 connector for VC supply; see page 98) llenwrench4 6.6 Nm / 4.9 lbft W 3 llenwrench4 6.6 Nm / 4.9 lbft 66.5.6 llenwrench4 6.6 Nm / 4.9 lbft Wrench 4-9.8 Nm / 7. lbft Spool: Wrench 9 CE llenwrench4 6.6 Nm / 4.9 lbft 6 6.38 5.59 DU 55

SD6 control kits Complete controls 8ES solenoid control Solenoid direct control with spring return to neutral position; it needs special spools and standard working section body (body kit without seals on spool). Description example: EL SD6 / - 8ES3 4 (G3 - ) - SE - VDC. 3. 4. 6. 5. 6.. 6.. 5. 4. 8ES3 8ES. 8ES3 8ES 4. 8ES 4.. Complete working section * YE CODE DESCRIION -8ES3 -VDC 659 arallel circuit, double acting spool, double acting ON/OFF solenoid control. Working section kit * YE CODE DESCRIION /IM -ES 5EL67 Distribuzione in parallelo 8ES 4. 5. ort valves For codes please refer to page 3. 6. 3. Spools YE CODE DESCRIION (ES) 3CU5 Double acting, 3 positions, with and closed in neutral position (ES) 3CU55 Double acting, 3 positions, with and open to tank in neutral position 4. Control kit YE CODE DESCRIION 8ES 5CN86, with spring return to neutral position 8ES 5CN86, with spring return to neutral position 8ES3 5CN87 Double acting with spring return to neutral position 6. Coils YE CODE DESCRIION With ISO44 connector.5vdc 4SOL4 Nominal voltage.5vdc VDC 4SOL4 Nominal voltage VDC 4VDC 4SOL44 Nominal voltage 4VDC With Deutsch series D connector 4 -.5VDC 4SOL4 Nominal voltage.5vdc 4 -VDC 4SOL4 Nominal voltage VDC NOE (*) - Codes are referred to UN- UNF thread. 56 DU

control kits SD6 Complete controls 8ES solenoid control Electric wiring example 8ES3 kit double acting 8ES kit singleactingon 8ES kit singleactingon Connector Connector -- o battery Operating features CONROL Internal leakage () ( p = bar - 45 psi /=4 C) : 5 cm 3 /min -.9 in 3 /min COIL Nominal voltage tolerance... : +% ower rating... : 36 W Coil insulance... : class H Duty cycle... : % + ressure Operating condition diagram 4 6 8 (US gpm) 4 (bar) (psi) 3 45 3 Operation area 5 5 3 45 Flow (l/min) Wrench 4 Nm / 7.7 lbft llenwrench4 6.6 Nm / 4.9 lbft llen wrench 4-6.6 Nm / 4.9 lbft Wrench8-4Nm/7.7 lbft 3..9 Emergency manual override 93.5 3.68 7Nm 5. lbft Spool Coil with ISO44 connector (need connector type C: see page 98) Coil with Deutsch D connector (need connector typr C9: see page 98) DU 57

SD6 control kits Comandi completi 8IM proportional hydraulic kit:: code 5IDR67 It can be used with special spools and body kit without seals and ring on spool (standard body) code: 5EL67. It saldoavailablein8imf3 -SD6 configuration with screws for spool stroke adjustment, codie: 5IDR67. 38.5 V 37.5.48 V V SE6 V (bar) 5 5 ilot pressure ilot pressure - stroke diagram ort ort -. -... (in) 4.6 (psi) llenwrench4 6.6 Nm / 4.9 lbft 7 8.54 48.5.9-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) Spool overlap area Metering zone vailable spools YE CODE DESCRIION IM 3CU4 Double acting, 3 positions, with and closed in neutral position IM 3CU54 Double acting, 3 positions, with and open to tank in neutral pos. Operating features ilot pressure... : max. 5 bar / 73 psi Internal leakage () ( p = bar - 45 psi /=4 C -4 F)... : max. 6 cm 3 /min -.37 in 3 /min Connection example SVM4 hydraulic pilot control valve V V V V ilot pressure 3 (bar) 5 5.33.85 8IM control kit curve 75 with step.. (in).3.. 4. 6. Stroke.9 8 7.5 4 (psi) 3 7.5 7.6 (mm) 58 DU

port valves SD6 ntishock valves ( G 3 - ) ressure setting in bar. Spring type (,3,4). djustment type (G,H,Z). 3 mounted on port. mounted on port. 3 mounted on porta and. djustment type G: with screw H: valve set and locked Z: tamper proof configuration Wrench 4 Nm / 3 lbft Notch.5 mm /.59 in erformance data Spring nr. (green band) Spring nr. 3 (blue band) Standard setting: 63 bar / 9 psi Standard setting: bar / 45 psi 5 5 (US gpm) 5 5 (US gpm) 4 4 (bar) (psi) (bar) (psi) 3 45 3 45 ressure 3 5 ressure 3 5 4 6 Flow (l/min) 4 6 Flow (l/min) Spring nr. 4 (red band) Standard setting: bar / 9 psi 5 5 (US gpm) 4 (bar) (psi) 3 45 (% ) 5% ime response ressure 3 5 4 6 Flow (l/min) ressure 95% 9% %,3 IME RESONSE 5 bar 8 psi ime ( ) DU 59

SD6 port valves nti -shock and anti -cavitation valves U ( G 3 - ) ressure setting in bar. Spring type (,3,4). djusting type (G, H). U U U3 mounted on port. mounted on port. 3 mounted on ports and. djusting type G: with screw H: valve set and locked Wrench 4 Nm / 3 lbft Notch.5 mm /.59 in erformance data Spring nr. (green band) Spring nr.3 (blue band) Spring nr.4 (red band) Standard setting: 63 bar / 9 psi Standard setting: bar / 45 psi Standard setting: bar / 9 psi 5 5 (US gpm) 5 5 (US gpm) 5 5 (US gpm) 4 4 4 (bar) (psi) (bar) (psi) (bar) (psi) 3 45 3 45 3 45 ressure 3 5 ressure 3 5 ressure 3 5 4 6 Flow (l/min) 4 6 Flow (l/min) 4 6 Flow (l/min) (% ) 5% ime response (bar) 9 ressure drop 5 5 (US gpm) (psi) 5 ressure 95% 9% 5 bar 8 psi ressure 6 3 5 %, IME RESONSE ime ( ) 4 6 Flow (l/min) 6 DU

port valves SD6 nti -cavitation valves C mounted on port. mounted on port. 3 mounted on ports and. C C C3 Wrench 4 4 Nm / 3 lbft erformance data 3 (bar) ressure ressure drop 5 5 (US gpm) 4 (psi) 3 4 6 Flow (l/min) Valve blanking plug mounted on port. mounted on port. 3 mounted on ports and. 3 llenwrench8 4 Nm / 3 lbft DU 6

SD6 port valves ilot check valves Cast iron block with pilot check valves. S mounted on port. mounted on port. 3 mounted on ports and. S direct type with pre -opening 3 S S S3 36.4 G3/8 66.6 9.5.5.37.85 WLVOIL MDE IN ILY 7.76 6.5.46 4.3 93.56 = 3.66 = 97.5 = 3.84 =.6 = 4.79 =.39 7.5.69 Cast iron block Valve (on side) Mounting flange Example of extra machining on working section body 9±..4±.39 6±..±.39 Scale : 74.9.6 Milled surface with fixing threaded holes 58±..8 ±.39.47 M5 Nr.4 holes 9.35.47 6 DU

port valves SD6 ilot check valves configuration Example of pressure on port and port to tank Wrench 7 4 Nm / 3 lbft 3 configuration Example of pressure on port and port to tank Wrench 7 4 Nm / 3 lbft Wrench 9 4 Nm / 3 lbft Example of pressure on port and port to tank Example of pressure on port and port to tank erformance data ressure 4 (bar) 3 valve pressure drop 5 5 (US gpm) 5 5 (US gpm) 4 (psi) ilot ratio (bar) (psi) 45 ype With Main 3 45 pre--opening 3 3 / :5.3 4 6 Flow (l/min) 5 S :6 :3. ressure S valve pressure drop 4 6 Flow (l/min) 5 DU 63

SD6 intermediate section CS mid return manifolds Mid return manifolds for directional valve with left and right inlet both; they allow indipendent circuits with common outlet. C C-C SE8.5.89 6.5.46 C 38.5 85 3.35 Directional control valve mounting face Hydraulic circuit 75 75 Description example: SD6//C(YG3--)/8L/CS/8L/C(YG3--)--SE 64 DU

intermediate section SD6 DFG pressure compensated flow divider section he flow on the downstream sections can be adjusted from to 4 l/min ( to.6 US gpm) by means of graduated handwheel; flow exceeding setting goes to tank. C-C C M5 85 3.35 Compensator kit Code: 5CS3638 Wrench -4Nm/7.7 lbft 6.5.46 DFG section Code: 3EL46 6.63 C 38.5 Directional control valve mounting face 69.7 3.5 5.4 Flow control valve Code: XCR76 Wrench 7-4 Nm / 7.7 lbft Hydraulic circuit 75 Description example: SD6//C(YG3--)/8L/DFG/8L/RC--SE Flow regulation diagram Q in =45l/min/ US gpm - ut = bar / 45 psi rioritary flow (l/min) 4 3 (US gpm) 9 6 3 5 (l/min) 4 rioritary flow 3 ressure -flow diagram Q in =45l/min/ US gpm 3 (psi) (US gpm) 8 4 6 (bar) in - out 4 ressure drop 4 8 (US gpm) (psi) 8 6 4 3 4 5 Nr. of handwheel turn 5 5 5 ressure (bar) 3 4 5 rioritary flow (l/min) DU 65

SD6 intermediate section EI service relief valve section he operation of up stream section exclude the EI downstream section. he pressure of the downstream sections should be adjusted at least bar / 9 psi below the relief valve setting. Execution EI is prearranged for a second inlet. Execution EI Directional control valve mounting face C-C lug code 3X85 Wrench 6-4 Nm / 7.7 lbft C 85 3.35 Hydraulic circuit revious sections Following sections revious sections 75 Following sections C 38.5 Description example: SD6//C(YG3--75)/8L/EI(YG3 -)/8L/RC--SE EI section kit Code: 5EL4673 4 4.49 Direct overpressure relief valve ype: Y(G3) Code: 5KI53 Wrench9-4Nm/3 lbft For other types see page Execution EI 9.75 D D-D Schema elemento revious sections.5.89 Following sections 7.5.69 SE8 revious sections 75 Following sections D 38 Description example: SD6//C(YG3--75)/8L/EI(YG3 -)/8L/RC--SE 66 DU

intermediate section SD6 EV3 inlet section with regulated flow Intermediate inlet section with regulated flow prioritary valve and exceeding flow in pressure. From EV3, the regulated flow is supplied to left side working sections while the exceeding flow is supplied to right side working section. On EV3 is incorporate the main relief valve; the regulated flow is adjustable also with the circuit under pressure. he working sections are assembled with two end cover, the left one is plugged (type R code 63), while the right one has the tank port technical data: Max. inlet flow = 6 l/min (6 US gpm), max. regulated flow = 4 l/min (.6 US gpm). C Directional control valve mounting face 95 3.74 SE8 C-C SE6 joint kit Code: 5GIU6338 Wrench 3 4 Nm / 3 lbft 9 7.48 7.76 4.33 Service relief valve ype: (G3 -)/SD8 Code: 3XCR83 Wrench 4 4 Nm / 3 lbft EV3 section body Code: 3EL4633 Flow control valve Code: 5CR8633 Wrench3-4Nm/3 lbft C 38.5 Complete section SD6/EV3(G3 -) -SE Code: 6437 3.8 R cover Hydraulic circuit Standard outlet cover 5 5 (US gpm) 3 (bar) 4 (psi) 45 3 ressure Service relief valve performance data 4 6 Flow (l/min) Description example: SD6//R/8L/EV3(G3 -)/8L/RC--SE DU 67

SD6 intermediate section EV9 pressure compensated flow control section4. Section with pressure compensated 3--ways flow control cartridge valve. he regulated flow is supplied to down stream sections, while the exceeding flow goes to tank. max. inlet flow is 45 l/min, max. regulated flow is 3 l/min. Description example: complete working section EL SD6 / EV9.. 3. 38.5.83 C C-C 85 3.35 revious sections Following sections 5.59 4.33. 3. 8.7 C.3. Direct control valve mounting face Series circuit section Hydraulic circuit arallel circuit section. Complete section YE CODE DESCRIION EV9 64353 Fine handwheel operated EV9 6435 One turn with detent handwheel EV93 6435 With VDC proportional solenoid valve revious sections E C R Description example: SD6/4/C(JG3--)/.../S--8L/EV9/8L/.../RC--SE Following sections. Section body kit YE CODE DESCRIION EV9 5EL463 Include body and seals 3. Flow control valve YE CODE DESCRIION S Fine handwheel operated valve S6366 Valve with one turn with detent handwheel 3 S VDC proportional solenoid valve 68 DU

intermediate section SD6 EV9 pressure compensated flow control section Handwheel operated Continuous fine regulation One turn with detent Valve circuit Wrench 7 4 Nm / 7.7 lbft 33.3 Wrench 7 4 Nm / 7.7 lbft 38.5 E R C 44.73 94.5 3.7 With proportional solenoid control ISO44 connection (needs connector typre C, see page 98) Valve circuit 35.38 Solenoid operating features Nominal voltage.. : VDC ower rating... : 8 W Duty cycle... : % E R C Wrench 7 4 Nm / 7.7 lbft 94 3.7 Emergency push -button otentiometer for valve adjustment Example of solenoid flow control valve connection It s show a configuration with push--button panel type U model U//SC: for information contact Sales Dept. SO o battery Connector ISO44 erformance data 4 (l/min) riority flow 3 ressure -flow diagram Qin=45l/min( US gpm) Flow regulation diagram Qin=45l/min( US gpm) - = bar (45 psi) 3 (psi).3.6.9. Current () (US gpm) (l/min) 4 (US gpm) 9 F 9 3 6 3 riority flow J Y 6 3 F Y J Flow control valve type Flow control valve type Flow control valve type 3 3 9 5 7 ressure (bar) 3 4 (n.of turn) 4 8 6 4 (n.of clicks) DU 69

SD6 outlet section Ordering codes Ordering example: FS SD6 / RC - SE * vailable configurations RC: side outlet RD: upper outlet RE: upper outlet with side carry--over RK: upper outlet and closed centre See page 6.. 4. options RE -RK 3.. Outlet section parts Nr. CODE QY DESCRIION. 3FI67 Outlet cover body *. 3X85 SE8 plug * 3. 4GU48 6 4x,78 NR 7 SH O -ring seal Circuit options Nr. CODE QY DESCRIION 4. 443 G/4 plug for carry -over (RE) and closed centre (RK) options NOE (*) -- Items are referred to UN- UNF thread. 7 DU

outlet section SD6 Dimensional data and hydraulic circuit ype RC llen wrench 6-4 Nm / 7.7 lbft 9 4.9.5. 9.75 4.94.47 9.35 84.5 3.33 8 3.5 SE8 Directional control valve mounting face 3.8 8 3.5 M8 3. 4.57 ype RD SE8 llenwrench6 4 Nm / 7.7 lbft.5. ype RE DIN96 -G/4 tapered plug llenwrench7 4 Nm / 7.7 lbft C C ype RK DIN96 -G/4 tapered plug llenwrench7 4 Nm / 7.7 lbft llenwrench6 4 Nm / 7.7 lbft DU 7

SD6 7 DU

DLS7 Content Content Dimensional data... 74 Hydraulic circuit... 75 erformance data... 76 Ordering codes... 77 Inlet and outlet cover ordering codes... 78 dimensional data and hydraulic circuit... 79 Working section ordering codes... 79 dimensional data and hydraulic circuit... 8 spools... 83 side spool positiones... 85 side options... 87 complete controls... 9 port valves... 59 Return cover... 93 DU 73

DLS7 Dimensional data (with inlet flow control valve) 9.5.6 E F 38 3.5..5.98.39 36.4 94 3.7 7.83 65.56 4.5.57 3.9 4.7 45.77 9 3.58,5 3.8 M8.5.4 4.5.57 36.5.44 WLVOIL 6 MDE IN ILY 3.8 56.5. M 48.5 38 38 37.9.5.5.46 6.5.79 7.5.4 4.63 3 Code WLVOIL 6 MDE IN ILY roduction batch : 6 = production year (6) = progressive number YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb DLS7/ 4.76 69.7 6.4 4. DLS7/6 3.4 59. 9. 4. DLS7/ 59 6.6 7 4. 8.9 9.6 DLS7/7 349 3.74 97.7.7 47.8 DLS7/3 97 7.76 45 5.7.5 4.4 DLS7/8 387 5.4 335 3. 4.3 53.5 DLS7/4 35 9.5 83 7. 4 3.9 DLS7/9 45 6.73 373 4.7 6.9 59. DLS7/5 73.74 8.7 6.6 36.6 DLS7/ 463 8.3 4 6. 9.5 64.9 74 DU

DLS7 Hydraulic circuit Fixed displacement pump (open center) LS 75 Z Z Description example: DLS7//M(G3--)/6S8MCLFG/6S8MCLFG/RF--SE Variable displacement pump with load -sensing compensator (closed center) LS LS Z Z Description example: DLS7//(SV)/6S8MCLFG/6S8MCLFG/RF--SE Configuration with L.S. relief valve is also available. LS 75 Z Z Description example: DLS7//N(G3--)/6S8MCLFG/6S8MCLFG/RF--SE DU 75

DLS7 erformance data (pressure drop vs. flow) Open center From inlet to outlet. ressure drop 4 (bar) 3 5 5 (US gpm) 54 (psi) 36 8 5 5 75 Flow (l/min) Inlet to work port From inlet to port (spool in position ) or port (spool in position ). ressure drop 4 (bar) 3 5 5 (US gpm) 54 (psi) ( ) ( ) 36 8 4 6 Flow (l/min) Work port to outlet From port (spool in position ) or port (spool in position ) to outlet. ressure drop 4 (bar) 3 5 5 ( ) ( ) (US gpm) 54 (psi) 36 8 NOE -- Measured with spool type 6S. 5 5 75 Flow (l/min) 76 DU

DLS7 Codici di ordinazione. Description example of standard configuration: a section following section 39.Ordering codes DLS7 / / M(G3 -) / 6V8MCLFG / 6V8MCLFG / RF - SE Nr.ofworking section.. 3. 3. zzrzzr 4... 4.. Complete inlet / outlet cover * page 78 YE CODE DESCRIION M(G3 -) 637 With flow control valve and L.S. overpressure relief valve (SV) 6373 Without flow control valve and L.S. overpressure relief valve N(G3 -) 637 Without flow control valve, with L.S. overpressure relief valve. Complete working section * page 8 YE CODE DESCRIION 6V8MCLFG 67 arallel circuit, double acting spool with spring return, lever control 6V8IMF3 67 arallel circuit, double acting spool, proportional hydraulic control with spool stroke adjusting NOE (*) -- Items are referred to UN- UNF thread. 3. Return cover * page 93 YE CODE DESCRIION RF 647 Standard type RH 6433 With L.S. signal carry -over 4. ssembling kit CODE 5IR86 5IR866 5IR84 5IR84 5IR88 5IR838 5IR8356 5IR8394 5IR843 5IR847 5IR858 5IR8546 DESCRIION tie rods with nuts for sections tie rods with nuts for sections tie rods with nuts for 3 sections tie rods with nuts for 4 sections tie rods with nuts for 5 sections tie rods with nuts for 6 sections tie rods with nuts for 7 sections tie rods with nuts for 8 sections tie rods with nuts for 9 sections tie rods with nuts for sections tie rods with nuts for sections tie rods with nuts for sections DU 77

DLS7 inlet and outlet cover Ordering codes4. Description example: FE DLS7 / M (G3 - ) - SE.. ressure relief valve setting (bar). Cover body kit * CODE DESCRIION 5FI377 standard type. Inlet options page 79... On Load -sensing signal IO CODICE DESCRIZIONE M(G3) 5KI73* Compensator kit with overpressure valve (from 8 to 35 bar / 5 to 46 psi, standard setting bar / 75 psi) (SV) 5KI73 Compensator and overpressure valve blanking kit N(G3) 5KI73 Compensator blanking kit with overpressure valve (from 8 to 35 bar / 5 to 46 psi, standard setting bar / 75 psi). NOE (*) -- Codes are referred to UN- UNF thread. Dimensional data and hydraulic circuit It s shown an M inlet and outlet cover. SE8 9 3.54 36.4 36.4 8.5.33 Directional control valve mounting face 3.5.53 M8 4.5.57 65.56 38 4.7.5 5.98 89 3.5 G/ 48.5.9 38.5.5 9 C LS C 86 max. 7.3 max. 78 DU

inlet and outlet cover DLS7 ype M with flow control valve and L.S. overpressure relief valve Dimensional data and hydraulic circuit For systems with fixed displacement pumps (open center version); see page 75. Wrench 3 llenwrench4 6.6 Nm / 4.9 lbft C-C LS llen wrench 6-4 Nm / 7.7 lbft llenwrench4-6.6nm/4.9 lbft Wrench 3 4 Nm / 7.7 lbft llenwrench4 Hydraulic circuit LS.5mm.59 in Compensator kit (M) Overpressure relief valve llenwrench3 llenwrench4-6.6nm/4.9 lbft mm.39in 75 ype without flow control valve and L.S. overpressure relief valve For systems with variable displacement pumps (closed center version); see page 75. llenwrench4 6.6 Nm / 4.9 lbft C-C LS llenwrench4 6.6 Nm / 4.9 lbft Hydraulic circuit LS llenwrench6 4 Nm / 7.7 lbft LS (N -) compensator blanking kit llenwrench4-6.6nm/4.9 lbft Overpressure valve blanking kit ype N without flow control valve, with L.S. overpressure relief valve For systems with variable displacement pumps (closed center version); see page 75. llenwrench4 6.6 Nm / 4.9 lbft C-C LS llenwrench4-6.6nm/4.9 lbft Wrench 3 4 Nm / 7.7 lbft Hydraulic circuit LS llenwrench4.5mm.59 in (N -) compensator blanking kit llenwrench3 llenwrench4-6.6nm/4.9 lbft Overpressure relief valve 75 DU 79

DLS7 working section Ordering codes4. Description example: EL DLS7 / 6V 8MC LFG. 3 (G3-5) - SE * mounted on port. mounted on port. 3 mounted on and ports... 3. 4. 5. ort relief valve setting in bar EL DLS7 / 6V 8IMF3 - SE * 6. 3. 7F 5. 8MC U 8DMC. C 4. I 3 8Z LFG SL. Q 8 DU

working section DLS7 43.Ordering codes. Working section kits * page 8 YE CODE DESCRIION - 5EL577 arallel circuit with port valves prearrangement Include body, seals, rings and load check valve.. Spools page 83 YE CODE DESCRIION l/min.6 US gpm l/min 5.3 US gpm 3 l/min 7.9 US gpm 4 l/min.6 US gpm 5 l/min 3. US gpm 6 l/min 5.6 US gpm D V Q C S Nominal flow with 4 bar / 3 psi stand -by 6 3CU3 3CU3 3CU33 3CU34 3CU35 3CU36 Double acting, 3 position, with and closed in neutral position 7 3CU35 3CU35 3CU353 3CU354 3CU355 3CU356 Double acting, 3 position, with and to tank in neutral position 3. side spool positioners page 85 YE CODE DESCRIION 7F 5V745 With friction 8MC 5V85 With spring return in neutral position 8DMC 5V85 s type 8 and pin with M8 female thread for dual control 8Z 5V8579 roportional pneumatic kit 8IZ 5V868 roportional hydraulic kit 4. side options page 87 YE CODE DESCRIION LFG 5LEV78 Zama (zic alloy) lever with with adjustable flow limiters SL - Without leve box SL 5CO7 Without lever box, with dust -proof plate SLCZ 5CO53 Without lever box, with endcap. Q 5EL7 Flexible cable connection; for CD cables LC 5CLO Joystick lever for sections operation 6. Complete controls * page 9 8IMF3 proportional hydraulic control kit with flow limiter. I Optional handlevers YE CODE DESCRIION L/Mx5 75 For LFG lever box, L = 5mm / 5.9 in L8/Mx 73 For LC joystick, L = mm / 7.87 in 5. ort valves page 59 YE CODE DESCRIION ssembled on section 3 X548 and ports valve blanking plugs C 5KI46 nti -cavitation nti -shock valve (G) 5KI6 From 5 to 5 bar / 75 to 8 psi standard setting 63 bar / 9 psi (G3) 5KI63 From to bar / 45 to 9 psi standard setting bar / 45 psi (G4) 5KI64 From 6 to 35 bar / 3 to 46 psi standard setting bar / 9 psi nti -shock and anti -cavitation valve U(G) 5KI36 From 5 to 5 bar / 75 to 8 psi standard setting 63 bar / 9 psi U(G3) 5KI363 From to 5 bar / 45 to 36 psi standard setting bar / 8 psi U(G4) 5KI364 From 6 to 35 bar / 3 to 46 psi standard setting bar / 9 psi Standard setting is referred to l/min flow. Flange mounted type X673 and S valves blanking plug Direct type 6* lock with valve on port 6* lock with valve on port 3 6* lock with valves on ports and XCR65 Single valve With re -opening S 633* lock with valve on port S 634* lock with valve on port S3 63* lock with valves on ports and S XCR65 Single valve NOE (*) -- Items are referred to UN- UNF thread. DU 8

DLS7 working section Dimensional data and hydraulic circuit Working section kit is fitted with body (), washer (), spool O--ring seals (3), load chek valve (4), assembling O--ring seals (5), plug on L.S. signal (6) and ball on shuttle valve (7). Working sections are supplied with port valve prearrangement. Drawing shows a complete working section, type DLS7/--7S8MCLFG--SE. D 94 3.7 58.8 4.37 Hydraulic circuit D 3 36.5 3.44 4.7.8 C C 38.5 Z 37.5 45.48.77 8.66 D-D C-C Z llen wrench 6.6 Nm / 4.9 lbft 4.5.8 8 DU

working section DLS7 Spools ype 6S LS " stroke + 5.5 mm +.in LS ---- closed LS stroke - 5.5 mm -. in ype 7S LS " stroke + 5.5 mm +.in LS closed, and to tank LS stroke - 5.5 mm -. in DU 83

DLS7 working section Spools Spool metering with M inlet cover and 4 bar / 3 psi standard stand -by 8 (l/min) 6 6S 6C 6Q -. -.5 -. -.5.5..5. (in) 6S 6C 6Q (US gpm) 5 Flow 4 6 6V 6D 6 6V 6D 5-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) Spool metering with N inlet cover With bar / 45 psi L.S. pump stand -by 8 (l/min) Flow 6 4 6S 6C 6Q 6 6V -. -.5 -. -.5.5..5. (in) 6S 6C 6Q 6 6V (US gpm) 5 6D 6D 5-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) With bar / 9 psi L.S. pump stand -by 8 (l/min) 6 6S 6C 6Q -. -.5 -. -.5.5..5. (in) 6S 6C 6Q (US gpm) 5 Flow 4 6 6V 6D 6 6V 6D 5-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) 84 DU

control kits DLS7 side spool positioners With friction type 7F llenwrench4-9.8nm/7. lbft Wrench 34 4 Nm / 7.7 lbft llenwrench4 69.5.74 llenwrench4-6.6nm/4.9 lbft With spring return 8MC kit llenwrench4 6.6 Nm / 4.9 lbft llenwrench5 9.8 Nm / 7. lbft 36.5.44 3 (N) Force - Force -stroke diagram -. -... (in) (lbf) 6 - - 4-3 - 6-6 -5-4 -3 - - 3 4 5 6 Stroke (mm) 4-8DMC kit Spool end joint code XER354 is available on request in order to screw onto pin. llenwrench4-6.6nm/4.9 lbft Spool end joint dimension Wrench 9-9.8 Nm / 7. lbft.47.43 M6 36.5.44 44.73 5h.59 4.6 8.3.39.79 8.3 8.7 4.57 M6 DUF 85

DLS7 control kits side spool positioners 8Z proportional pneumatic control Special wrench - 4 Nm / 7.7 lbft V V NF -/8 n. ports 43 57.69.4 V V llenwrench4-6.6nm/4.9 lbft 33.3 9 4.69 Wrench 9-4 Nm / 7.7 lbft Wrench3-4Nm/7.7 lbft llenwrench4-6.6nm/4.9 lbft Operating features Max. pilot pressure... : bar / 45 psi -. -... (in) 8 (psi) (bar) 6 9 5.8 84 ilot pressure 4 ilot pressure - stroke diagram ort ort - 6-5 - 4-3 - - 3 4 5 6 Stroke (mm) 6 3 Spool overlap area Metering zone 8IZ proportional hydraulic control It can be used with body kit without seals and ring on spool (standard body) on side code: 5EL573. llenwrench4 6.6 Nm / 4.9 lbft SE6 nr. ports V 4 4.94.57 V V V 34.5.36 6.63 Wrench 3 84 3.3 96.5 3.8 Notch.6 mm /.63 in 4 Nm / 7.7 lbft Operating features Max. pilot pressure... : 5 bar / 75 psi 4 (bar) ilot pressure 3 ilot pressure - stroke diagram ort ort -. -... (in) 35-6 - 5-4 - 3 - - 3 4 5 6 Stroke (mm) (psi) 45 3 5 Spool overlap area Metering zone 86 DUF

control kits DLS7 side options Lever controls LFG type Cast iron lever pivot box with protective rubber bellow; it s complete of two screws for spool stroke adjusting in both directions. It can be rotated 8 (configuration LFG8). Vertical handlever assembly Horizontal handlever assembly M8.79 65.5.58 8.5 3. Stroke end screw for position : allen wrench.5 Fixing nut: wrench 8-6.6 Nm / 4.9 lbft Stroke end screw for position : allen wrench.5 Fixing nut: wrench 8-6.6 Nm / 4.9 lbft 3.8 56.5. 63.4 max..5 max. Controls prearrangement SL type SL type SLCZ type 38.5 3.8.3 8 llenwrench4 6.6 Nm / 4.9 lbft llenwrench4 6.6 Nm / 4.9 lbft.83 8.3. 7.5.44.85 9H8.35 5.59 Mechanical control with dust--proof plate kit. rotection cap usable with pneumatic 8, electro--pneumatic 8E3, and electro--hydraulic 8ED3 spool positioners. DUF 87

DLS7 control kits side options Q cable remote control kit Waterproof cap prearranged for remote control with flexible cable. llenwrench4-6.6nm/4.9 lbft Wrench 3 Wrench - 9.8 Nm / 7. lbft Wrench4-4Nm/7.7 lbft 9 3.58 Flexible cable NOE - For further information about remote cable control, require related documentation. Example of cable control SCF3 remote control Q kit CD flexible cables DLS7/ directional control valve without lever boxes 88 DUF

control kits DLS7 side options LC joystick nd section spool st section spool Execution LC llenwrench3-9.8nm/7. lbft Wrench3-4Nm/3 lbft llenwrench6 4 Nm / 7.7 lbft ivot Wrench 3 Wrench 4 NOE - he handlever must be ordered separately (see page 8). Dimensions and movement scheme Execution LC pivot placed down on the left Execution LC pivot placed down on the right st section axis nd section axis - - - - - - - M 8.39. - 9.75 87 3.43 43.69 Execution LC3 pivot placed above on the left Execution LC4 pivot placed above on the right - - - - - - - - NOE - Due to limited space in case of LC3 or LC4 configuration the assembly of ports service relief valves is not possible. DUF 89

DLS7 control kits Complete controls47. 8ESF solenoid control Solenoid direct control with spring return to neutral position; it needs special spools and standard working section body (body kit without seals on spool); fitted with screws for spool stroke adjusting in booth directions. Description example: EL DLS7 / - 6V 8ES3F3 (G3-5) - SE - VDC.. 3. 4. 5. 6. 4. 6. 5.. 4.. Complete working section * YE: -6V8ES3F3 -SE -VDC CODE: 67 DESCRIION: arallel circuit, double acting spool, double acting ON/OFF solenoid control 3. 6.. Working section kit * YE CODE DESCRIION /ES 5EL5778 arallel circuit NOE (*) - Codes are referred to UN- UNF thread. 3. Spools YE CODICE DESCRIION from5tol/min from.3 to 5.3 US gpm from to 4 l/min from 5.4 to.6 US gpm from 4 to 6 l/min from.7 to 6 US gpm V Q S Nominal flow with 5 bar / 8 psi stand -by 6 3CU3 3CU34 3CU36 Double acting, 3 pos., with and closed in neutral 7 3CU35 3CU354 3CU356 Double acting, 3 pos., with and to tank in neutral 4. Control kit YE CODE DESCRIION 8ES3F3 5CN8 Double acting with spring return to neutral position 5. ort valves For codes please refer to page 8. 6. Coils YE CODE DESCRIION With ISO44 connector.5vdc 4SOL4 Nominal voltage.5vdc VDC 4SOL4 Nominal voltage VDC 4VDC 4SOL44 Nominal voltage 4VDC With Deutsch series D connector 4 -.5VDC 4SOL4 Nominal voltage.5vdc 4 -VDC 4SOL4 Nominal voltage VDC 9 DUF

control kits DLS7 Complete controls 8ESF solenoid control Electric wiring example 8ES3F3 kit double acting Connector Connector -- o battery + Operating features CONROL Internal leakage () ( p = bar - 45 psi /=4 C) : 5 cm 3 /min -.9 in 3 /min COIL Nominal voltage tolerance... : ±% ower rating... : 36 W Coil insulance... : class H Duty cycle... : % Wrench 3 4 Nm / 7.7 lbft Wrench 9.8 Nm / 7. lbft Wrench 3 4 Nm / 7.7 lbft 3.94 3.6 llenwrench3 llenwrench4 6.6 Nm / 4.9 lbft Spool Coil with ISO44 connector (need connector type C: see page 98) Coil with Deutsch D connector (need connector typr C9: see page 98) DUF 9

DLS7 control kits Complete controls 8IMF3 proportional hydraulic kit With screws for spool stroke adjusting in both directions, code 5IDR7. It can be used with special spools and body kit without seals and ring on spool (standard body) code: 5EL577. llenwrench4 V 3.6 46.8 58 max..8 max. V V SE6 V llenwrench4-6.6nm/4.9 lbft Wrench 3-4 Nm / 7.7 lbft 36 9.9 7,6 (bar) 5 ilot pressure 5 3 ilot pressure - stroke diagram Max. pilot pressure 5 bar -- 75 psi. ort ort -. -... (in) -6-5 -4-3 - - 3 4 5 6 Stroke (mm) Spool overlap area Metering zone vailable double acting spools YE CODES DESCRIION l/min.6 US gpm Connection example l/min 5.3 US gpm 3 l/min 7.9 US gpm 4 l/min.6 US gpm 5 l/min 3. US gpm 6 l/min 5.6 US gpm Nominal flow with 4 bar / 3 psi stand -by D V Q C S 6 3CU33 3CU33 3CU333 3CU334 3CU335 3CU336 3 pos., with and closed in neutral pos. 7 3CU335 3CU335 3CU3353 3CU3354 3CU3355 3CU3356 3 pos., with and to tank in neutral pos. (psi) V V SVM4 hydraulic pilot control valve ilot pressure 8IMF3 control kit: curve 75 with step 3 (bar) 5 5.33.85.. (in).3.. 4. 6. Stroke.9 8 7.5 4 (psi) 3 7.5 7.6 (mm) V V 8IMF3 control kit: curve 78 without step ilot pressure 3 (bar) 7 6.5.33.85.. (in).3.3 5.8.. 4. 6. Stroke 47 94 4 (psi) 3 7.6 (mm) 9 DUF

return section DLS7 Dimensional data and hydraulic circuit ype RF standard llen wrench 6-4 Nm / 7.7 lbft Hydraulic circuit.47 35.5.4 6.5.4 33.3.39 44.5.75 9.5 3.56 M8 9 4.9 9 9.35 3.58 Directional control valve mounting face ype RH With L.S. signal power beyond, for two DLS7 directional valve connection: dimensions are the same of RF return cover. LS 4.5.57 SE6 Hydraulic circuit example LS LS 5 5 8 8 LS Z Z Z DU 93

SD6 - DLS7 Installation and maintenance he SD6 and DLS7 valves sre assembled and tested as per the technical specification of this catalogue. efore the final installation on your equipment, follow the below recommendations: -- the valve can be assembled in any position; in order to prevent working section deformation and spool sticking mount the product on a flat surface; -- in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly on the valve; -- prior to painting, ensure plastic port plugs are tightly in place. SD6 DLS7 C LS Configuration with powe beyond Configuration with N inlet cover Fitting tightening torque - Nm / lbft SD6 DLS7 HRED YE port ports. ports C, ports, ports, LS signal S G3/8 G3/8 G/ G/ G3/8 G/4 With O--Ring seal 35 / 5.8 35 / 5.8 5 / 36.9 5 / 36.9 35 / 5.8 / 5.7 With copper washer 4 / 9.5 4 / 9.5 6 / 44.3 6 / 44.3 4 / 9.5 5 / 8.4 With steel and rubber washer 3 /. 3 /. 6 / 44.3 6 / 44.3 3 /. 6 /.8 UN--UNF 3/4--6 (SE 8) 9/6--8 (SE 6) 3/4--6 (SE 8) 3/4--6 (SE 8) 9/6--8 (SE 6) 9/6--8 (SE 6) With O--Ring seal 5 / 36.9 3 /. 5 / 36.9 5 / 36.9 3 /. 3 /. MERIC M8x.5 M8x.5 Mx.5 With O--Ring seal 35 / 5.8 35 / 5.8 5 / 36.9 With copper washer 4 / 9.5 4 / 9.5 6 / 44 With steel and rubber washer 4 / 9.5 4 / 9.5 6 / 44.3 NOE -- hese torque are recommended. ssembly tightening torque depends on many factors, including lubrication, coating and surface finish. he manufacturer shall be consulted. 94 DU

SD6 Installation and maintenance It s shown a section of SD6//C(YG3--75)/8L/8L/RC--SE valve. Washer chamfer Sealing edge Callout ) Inlet cover ) Overpressure relief valve 3) Working section 4) Spool: normally spools are inter_ changeable, verify the smoothness during the assembly 5) side spool positioner 6) Lever pivot box 7) ort relief valve prearrangement 8) Load check valve 9) Outlet cover )Holding O -Ring washer ) 6.6x.8 arback seal code: 4NE8634 ) 5.88x.6 O -ring seal code: 4GU596 NOE -- ll moving parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI Malfunction Cause Remedy External leakage pivot box lever or control kit side. Excessive internal leakage on and ports. Dropping load during transition while raising. Worn spool seal due to mechanical actuation or high back pressure. Increase clearance between spools and body due to high wear. High leakage on the load check valve. Locate the leakage and replace the seal. Check back pressure level. Replace the working section and check the oil contamination level. Remove the load check valve and clean the seat, verifing it s not dented. Inability to build pressure on and ressure relief valve blocked open. Remove and clean or replace the valve. ports. Low pump pressure and flow. Check the pump and circuit. DU 95

DLS7 Installation and maintenance It s shown a section of DLS7//M(G3--)/6V8MCLFG/6V8MCLFG/RF--SE valve. Washer chamfer Sealing edge Callout ) Inlet and outlet cover ) Compensator kit 3) L.S. overpressure relief valve 4) Working section 5) Spool: normally spools are inter_ changeable, verify the smoothness during the assembly 6) side spool positioner 7) Lever pivot box 8) ort relief valve prearrangement 9) Load check valve ) Return cover ) Holding O -Ring washer ) 5.88x.6 O -ring seal code: 4GU596 NOE -- ll moving parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI 96 DU